BW 1000W
BW 1200W
BWD 1300W
2
This appliance complies with the provisions of the 89/336/EC Directive
regarding electromagnetic compatibility and the 73/23/EC directive Low
Voltage regarding electrical safety and the 93/68/EC Directive for CE
marking.
3
1-SPECIFICATION
2- INSTALLATION
3- HANDLING
4- MAINTENANCE
5- CAUTIONS AND ADVICE
6- SAFETY FEATURES
7- CONTROLS
8- WASH PROGRAMME TABLE
INDEX
- Dimensions...........................................Height..................................85 cm
1 - SPECIFICATION
1.1 - Technical data
Width...................................60 cm
- Washing/Drying capacity.......................Cotton.....................5,5 kg/2,75 kg
Depth...................................55 cm
- Power supply voltage (m.f.)...............................................230 V ~ 50 Hz
- Maximum power consumption-washing/Drying................2.200 W/ 1.450 W
1.2 -Description of the washing machine & Washer-Dryer
- Water consumption, cotton
wash at 60ºC (without pre-w.)
- Energy consumption, cotton
wash at 60ºC (without pre-w.)
- Spin speed........................................................................
B- Detergent drawer
H- Filter door
L- Pilot lamp
P- Programme selector
T- Temperature selector
C- No spin push-button
R- 550/1000-1300 rpm push-button
U- Door opening handle
I- Adjustable feet
Y- Extra rinse push-button
- Energy consumption, drying (cotton 2,75 kg)...................................2 kWh
- Water consumption, drying (cotton 2,75 kg)........................................50 l
S- Drying time selector
X- ON/OFF push-button
4
Ap. 7 CONTROLS
M- Half load push-button
V- Spin speed selector
A- Rinse hand hold push-button
Wash/Dry
Synthetics...............2,75 kg/1,5 kg
Wool...........................1 kg
1 wash cycle + drying .................................................5,03 kWh
{
200 wash cycles + drying..........................................1.006 kWh
1 wash cycle + drying..................................................150 l
200 wash cycles + drying.........................................30.000 l
{
1300
9.800 l
rpm
206
kWh
1 cycle of wash...........
{
200 cycles of wash......
1 cycle of wash...........
200 cycles of wash.......
{
1,03
kWh
49 l
- Energy consumption
wash + 2 drying cycles
- Water consumption
wash + 2 drying cycles
1200
9.800
206
1,03
49
1000
9.800
206
1,03
49
- Models............................................................................
BW 1000W BW 1200W BWD 1300W
B
U
H
I
2- INSTALLATION
2.1 - Removing transit bolts
Proceed as follows:
-Let the water run for a while before connecting the hose.
-Connect the water inlet hose applying the rubber joint provided in the fittings
equipment bag.
-Position the drainage hose inside a hose of a larger diameter, or rest it well
fastened against any kind of drain at the height indicated.
-Neither of the hoses should be twisted or kinked.
2.) Push with a screwdriver at an angle
in the screw holes until the four spacers
(H) fall.
2.2 -Plumbing connection
The "H" connection can only
be applied in those machines
f itted for this (Bithermical).
H- Hot water connection.
C- Cold water connection.
After removing the external packing
the drum must be released before the
machine is used.
This is done in the following manner:
1.) Unscrew and remove the four
screws A-B-C-D.
3.) It is very important to recover these
four spacers (H) because they could
cause damage if they remain inside the
machine and also because they will be
required to move the machine in the
case of moving house.
The user will require a tap with a 3/4" gas screwthread outlet and a drain
situated between 50 and 80 cms. above floor level. The watermain pressure
must be between 0,4 and 10 bar inclusively.
5
These must be recovered and kept.
C
H
Max.80 cm.
Min.50 cm.
C
H
THERMO
D
C
B
A
H
- Use new tubes for connecting to the water supply.
6
In order to prevent noise and vibration,
ensure that the machine is not touching any
nearby walls or furniture.
2.3 - Levelling
2.4 -Electrical connection
For the appliance to work under optimum conditions, it needs to be levelled
perfectly, i.e.horizontal and stable.
Once the levelling is done, block the
adjustable feet by tightening the nut "J".
That the power supply, is single-fhase 220-
230 V ~ (230-240 ~ for UK).
That the user's meter, limiter, fuses, power
socket and installation are of an adequate
output for the power indicated on the
characteristics plate of this washing machine.
10 A 250 V fuse (13 A 250 V for UK).
If the wall socket does not have an earth
connection, you must connect the central
earth connection of the washing machine to
good ARTIFICIAL EARTH (consult your
dealer).
THE WASHING MACHINE MUST BE WELL EARTHED.
NOTE: If the power supply cable is damaged, it should be substituted by
a specially prepared replacement cable, to be supplied by the
manufacturer, or by the off icial after salesTechnical Service Organisation.
Use a wall socket with an earth connection.
Make periodic checks that the machine is
levelled by repeating these operations if
necessary.
Before connecting the washing machine to the power supply, the following
points should be checked through:
The manufacturer declines all responsibility for any accidents on ocurrences
caused by a defective earth connection or lack thereof.
I
J
The wasing machine's plug guarantees the
machine's earthing.
Once the machine has been positioned in ist
place, work the adjustable feet "I" at the
front of the washing machine, until it is
horizontal and the four feet are resting
f irmly on the floor.
Loading...