Page 1
BTC6530BL/SS
BTC9530BL/SS
Cooker Hood
Page 2
User Manual for your Baumatic
BTC6530BL/SS
BTC9530BL/SS
Cooker Hood
60 cm Cooker hood in black
60 cm Cooker hood in stainless steel
90 cm Cooker hood in black
90 cm Cooker hood in stainless steel
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
DD 24/01/08
2
Page 3
Contents Page
Environmental note 4
IMPORTANT SAFETY INFORMATION 5 – 7
Specifications of your BTC6530BL/SS cooker hood 8
Specifications of your BTC9530BL/SS cooker hood 9
Using your Baumatic cooker hood 10
Before first use 10
To use your cooker hood 10 - 11
Cleaning your Baumatic cooker hood 11
The grease filters 11
Maintenance 12 - 14
Removing and cleaning the grease filters 12
Changing a light bulb 13
Fitting the carbon filters 14
Installation 15 - 23
Electrical connection 15 - 16
Before beginning installation 16 - 17
Installing your cooker hood 17 –19
Connecting to external ducting 20
Fitting the chimney 20 – 22
Completing the installation 23
Extraction mode or recirculation mode? 23
Troubleshooting 24 - 25
Contact details 26
3
Page 4
ENVIRONMENTAL NOTE
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any
plug useless. Cut the cable off directly behind the appliance to
prevent misuse. This should be undertaken by a competent
person.
CONFORMITY TO W.E.E.E. DIRECTIVE
4
Page 5
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of the information contained in
this booklet, please contact the Baumatic Technical
Department.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
o The hood must be installed in accordance with the installation
instructions and all measurements followed.
o If the cooker hood is installed for use above a gas appliance then
the provision for ventilation must be in accordance with the Gas
Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural
Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation &
Use) Regulations, the Building Regulations issued by the
Department of the Environment, the Building Standards
(Scotland) (Consolidated) Regulations issued by the Scottish
Development Department.
o It is dangerous to alter the specifications or to modify this
product. Do not tamper with it or attempt to modify the
appliance in any way.
o When installing the hood, ensure that the following
recommended distances are observed between the highest point
on the hob top (including the burners) and the bottom of the
cooker hood:
¾ Electric cookers: 700 mm
¾ Gas cookers: 700 mm
¾ Coal/ oil cookers: 800 mm
IMPORTANT: DO NOT SET YOUR COOKER HOOD LESS
THAN 700mm ABOVE YOUR COOKER.
o When installed between adjoining wall cabinets, the cabinets
must not overhang the hob.
5
Page 6
o The edges of the cooker hood are sharp – be mindful of this as
you handle your appliance, especially during installation and
cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS!
o If the room where the cooker hood is to be used contains a fuel
burning appliance such as a central heating boiler then its flue
must be of the sealed or balanced flue type.
o If other types of flue or appliances are fitted, ensure that there is
an adequate supply of air in the room.
o When the hood is being used in its extractor function, ensure
that the ducting is fire retardant and that there are no bends
sharper than 90 degrees as this will reduce the efficiency of the
hood.
o Ensure the ducting for the extractor function has the same
diameter as the outlet hole all the way through.
o Keep young children from using, playing with
or tampering with the cooker hood. Older
children and infirm persons should be
supervised if they are using the cooker hood.
o Your cooker hood is for domestic use only.
o Please dispose of the packing material carefully – children are
especially vulnerable to it.
o Dirty oil is an even greater fire risk.
o Always put lids on pots and pans when cooking
on a gas cooker.
o The manufacturer refuses to accept any responsibility for
damages arising to the hood or it catching on fire, from a failure
to observe the fire safety advice contained in this instruction
booklet.
6
Page 7
o Remember that when in extraction mode, your cooker hood is
removing air from your room. Ensure that proper ventilation
measures are being observed.
o Note that it removes odours from your room, not steam.
o Warning - Always ensure that the cooker
hood has been disconnected from the
power supply before carrying out any work
on the hood, including replacing light bulbs.
o Do not connect the ducting system of this appliance to any
existing ventilation system which is being used for any other
purpose.
o Do not install above a cooker with a high level grill.
o Never leave frying pans unattended during use
as overheated fats and oils might catch fire.
o Do not leave naked flames under the cooker
hood.
o Do not attempt to use the cooker hood if it is damaged in any
way. Never attempt to use it without the grease filters fitted or
if the filters are excessively greasy!
o Never flambé cook under this cooker hood.
o The lights on this appliance should only be used during operation
of the cooker hood. They should not be left on permanently and
used as a lighting source.
o The cooker hood should not be exposed to a direct heat source
from the cooking device underneath it, i.e. a naked flame from a
gas burner or heat from electric hob zones without a pan on
them.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY IN THE EVENT OF FAILURE TO
OBSERVE THE INSTRUCTIONS GIVEN HERE, FOR
INSTALLATION, MAINTENANCE AND SUITABLE
USE OF THE HOOD.
7
Page 8
Specifications of your BTC6530BL/SS cooker hood
Congratulations on purchasing a Baumatic cooker
hood!
PRODUCT DIMENSIONS
Height: 680 mm – 1040 mm
Width: 600 mm
Depth: 500 mm
DIMENSIONS OF CHIMNEY SECTION:
226 mm x 256 mm
Your stainless steel cooker hood is fitted with:
o High extraction tangential motor
o Push button control operation
o 3 Speeds
o 1 Metallic grease filter
o 2 halogen lights
Extraction capacity: 500 m³/hr
Noise level min/max: 54 – 62 dB
MODEL NUMBER CARBON FILTER REQUIRED
BTC6530BL/SS S1
8
Page 9
Specifications of your BTC9530BL/SS cooker hood
Congratulations on purchasing a Baumatic cooker
hood!
PRODUCT DIMENSIONS
Height: 704 mm – 1064 mm
Width: 900 mm
Depth: 543 mm
DIMENSIONS OF CHIMNEY SECTION:
226 mm x 256 mm
Your stainless steel cooker hood is fitted with:
o Superior extraction tangential motor
o Push button control operation
o 3 Speeds
o 2 Metallic grease filters
o 2 halogen lights
Extraction capacity: 500 m³/hr
Noise level min/max: 54 – 62 dB
MODEL NUMBER CARBON FILTER REQUIRED
BTC9530BL/SS S1
9
Page 10
Using your Baumatic cooker hood
Before first use
IMPORTANT: THIS PROCESS MUST BE FOLLOWED
BEFORE THE COOKER HOOD IS USED FOR THE FIRST
TIME.
o You should use a good quality stainless steel cleaner on ALL of
the stainless steel areas of your cooker hood, before it is used
for the first time.
o This will help to leave a silicone water-resistant film to protect
the stainless steel surfaces.
To use your cooker hood
o Make sure that it has been installed by a suitably qualified
person, as per the information contained in Baumatic’s
installation instructions.
o Find the control panel, which is located in the centre of the
canopy.
o There are several buttons on the control panel, which perform
separate functions.
o A = ON/OFF button
o B = Speed selection buttons
= Low speed
= Medium speed
= High speed
o C = Light on/off button
10
Page 11
IMPORTANT: IDEALLY YOU SHOULD TURN ON YOUR
HOOD TEN MINUTES BEFORE YOU START TO COOK,
OR AT THE VERY LEAST WHEN YOU BEGIN COOKING.
YOU SHOULD ALSO RUN YOUR HOOD FOR TEN
MINUTES AFTER YOU HAVE FINISHED COOKING.
Cleaning your Baumatic cooker hood
IMPORTANT: BEFORE CLEANING, ALWAYS
ENSURE THAT YOU HAVE SWITCHED YOUR
COOKER HOOD OFF AT THE OMNI-POLAR
SWITCH, SET AT THE WALL FROM THE CABLE.
Cleaning
o Clean the external parts of your cooker hood with mild liquid
detergent and a new damp cloth.
o Never use abrasive powder, corrosive solvents or brushes.
o Never insert pointed objects into the motor’s protective grid.
o Only clean the control panel and grease filter grill with mild liquid
detergents and a new damp cloth.
o If you are using the appliance in recirculation mode, then be
sure to replace the carbon filter at the recommended interval
(see section on “Fitting the carbon filter”). A build up of grease
could cause a fire hazard.
o Never attempt to clean the area above the grease filters.
The grease filters
o Your cooker hood includes grease filters which help to absorb
grease particles to protect your kitchen & furniture from greasy
residues.
o These metallic filters may become inflammable if they become
saturated with this greasy residue.
o To prevent this fire hazard, the filters should be cleaned
regularly. Depending on use, this should be done every 10-15
days or at least once a month, using hot water and normal
washing-up detergent.
o DO NOT WASH THE GREASE FILTERS IN A DISHWASHER.
11
Page 12
Maintenance
Removing and cleaning the grease filters
o First remove the grease filters by
pulling down on the handle and
pulling them away from the
cooker hood.
o Soak the grease filter in hot water and washing up liquid for
about an hour.
o Rinse them off thoroughly with hot water.
o Repeat the process if required.
o Refit the grease filters once they
have dried.
o IMPORTANT: Let the grease filters dry thoroughly before
refitting them in the cooker hood.
12
Page 13
Changing a light bulb
IMPORTANT: BEFORE ATTEMPTING TO CHANGE
A LIGHT BULB, YOU MUST ENSURE THAT YOU
HAVE DISCONNECTED THE COOKER HOOD FROM
YOUR MAINS SUPPLY.
o Remove the grease filter (as
described on page 12).
o Prior to touching the light bulbs ensure that they have cooled
down.
o Find the bulb that requires replacement, you will find it located in
the light fixture which is inside the exposed section of the
canopy.
o Use a screwdriver to remove the glass cover that sits over the
bulb. Unscrew the light bulb that needs to be replaced and insert
a new G4 20W (max) bulb. Then replace the glass cover.
o IMPORTANT: Defective bulbs should be replaced immediately.
o If the lights still do not work, make sure that the bulbs are fitted
properly into their housings before you call for technical
assistance.
o Refit the grease filter.
13
Page 14
Fitting the carbon filters
If the appliance is being used to be used in recirculation mode then it
is necessary to fit carbon filters. This will help to absorb unpleasant
odours caused by cooking.
IMPORTANT: BEFORE ATTEMPTING TO FIT OR
REMOVE THE CARBON FILTERS, YOU MUST
ENSURE THAT YOU HAVE DISCONNECTED THE
COOKER HOOD FROM YOUR MAINS SUPPLY.
1) Remove the grease filters.
2) Hook the carbon filter over
the pins that are located at the
end of the motor.
3) Turn the carbon filter anticlockwise, until you feel
it click into place.
o Repeat this process for the second carbon filter. You need to
place a carbon filter at either end of the motor.
o Refit the grease filters.
o The carbon filters should be replaced every three months or if
they show signs of damage.
14
Page 15
Installation
IMPORTANT: Before installation and usage read
all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
the rating plate are exactly the same as the
voltage and frequency in your home. The rating
plate can be found behind the grease filter.
The manufacturer declines all responsibility in the event of the installer
failing to observe all the accident prevention regulations in force,
which are necessary for normal use and the regular operation of the
electric system.
Electrical connection
YOUR COOKER HOOD IS INTENDED FOR FITTED AND
PERMANENT INSTALLATION.
o The cooker hood’s power cable must be fitted upstream from the
electrical connection, using an omni-polar switch with a contact
distance of at least 3 mm. THE FUSE MUST BE RATED AT 3
AMPS.
WARNING: THIS APPLIANCE MUST BE EARTHED. It
should only be connected by a competent person, using
fixed wiring via a double pole switched fused spur outlet.
(UK ONLY).
We recommend that the appliance is connected by a qualified
electrician, who is a member of the N.I.C.E.I.C. and who will comply
with the I.E.E. and local regulations. The wires in the mains lead are
coloured in accordance with the following UK code:
Blue = Neutral, Brown = Live, Green/Yellow = Ground
If you only find two wires in the main’s lead (blue and brown),
then neither must be connected to the earth terminal.
15
Page 16
o As the colours of the wires in the appliance’s mains lead may not
correspond with the coloured markings identifying the terminals
in your spur box, please proceed as follows:
o The blue wire must be connected to the
terminal marked “N” (neutral), or coloured
black.
o The brown wire must be connected to the
terminal marked “L” (live), or coloured red.
Before beginning installation
o Check that the product purchased is of a suitable size for the
chosen installation area. In addition check whether there is an
electrical socket available that will be accessible once the hood is
mounted. If the product is going to be used in extraction mode,
then there should also be space to connect a ducting hose to the
outside.
o Carry out all necessary masonry work prior to the fitting of the
cooker hood.
o Ensure that all electrical connections are carried out by a suitably
qualified person.
o Before commencing installation of the cooker hood the grease
filters should be removed.
o Check inside the product and insure that there is no transit
packaging or any other materials, such as packets of screws,
guarantees etc. These should be removed and kept for future
use.
o If possible, disconnect and move freestanding or slot-in cookers
from their position, to provide easier access to the rear wall and
ceiling. If this is not possible, then a thick, protective covering
should be placed over the worktop, hob top or cooker. This will
help to protect these surfaces from damage and debris.
o Select a flat surface for assembling the cooker hood. Cover that
surface with a protective covering and place all cooker hood
parts and fittings on to it.
o Rawl plugs are provided to secure the hood to most types of
walls and ceilings. However a qualified technician must verify the
suitability of the materials, in accordance with the type of wall
and ceiling. The wall and ceiling must be strong enough to take
the weight of the hood.
16
Page 17
o Do not tile, grout or silicone this appliance to the wall. This
appliance is designed to be surface mounted only.
Installing your cooker hood
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
INSTALLING YOUR COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
MODE. PLEASE TURN TO PAGE 23 NOW TO
UNDERSTAND THE DIFFERENCES BETWEEN THESE
TWO MODES.
o We recommend that at least two people install this hood.
IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO
YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION
PROCESS HAS BEEN COMPLETED.
1) Remove the metal grease filters.
2) Position the hood against the wall
that you are intending to install it on and
mark the position of the support holes
that are to be drilled (as shown in the
figure opposite).
17
Page 18
2a) The support screw holes
are indicated by figure A in
this drawing and the
anchoring screw holes are
indicated by figure B.
3) Using a drill bit with a 6 mm
diameter, make holes in the wall on the
positions that you have marked in step
2.
4) Insert rawl plugs into all of the holes that you have
drilled.
18
Page 19
5) Fasten the support screws
halfway in, leaving them 10 mm
out of the wall.
6) Hang the hood onto the
support screws.
7) Fully tighten the support screws (A) and then screw the anchoring
screws (B) through the relevant holes in the cooker hood. Fully
tighten the anchoring screws into the wall.
19
Page 20
Connecting to external ducting
8) Connect the coupling to the top of the cooker hood, and then
connect a 125 mm ducting hose to the coupling (please note that
the ducting hose is not supplied with the appliance).
o The other end of the ducting hose should be connected to a
discharge outlet that is suitable for cooking vapours. It should
have a cross section of at least 150 cm².
o The maximum distance between the coupling and your discharge
outlet should be 3 metres, with one 90 degree bend.
Fitting the chimney
9) Take the two chimney
sections (C and D).
o Rest the bottom of
chimney section C on the
top of the hood. You
should take care to
position the tabs on the
chimney section into the
rear of the hood.
o Mark the side
measurement of both
sides of chimney section C
on the wall with a pen
cil.
20
Page 21
0) Lift chimney section D upwards until it reaches the ceiling. You
1
must ensure that it is perpendicular to the hood.
o Mark the side measurement of both sides of chimney section D
on the wall with a pencil and then remove chimney section D.
1) Take the fixing bracket (E) and place it between the two pencil
1
marks that you made in step 9
o Keeping the bracket in contact with the wall, use a pencil to
mark on the wall the anchoring holes that are cut out of the
bracket
21
Page 22
2)
1 Using a 6 mm drill bit, drill out two holes on the pencil markings
at you made in step 11. Insert rawl plugs into the holes and then
th
se a screwdriver to secure the fixing bracket to the wall.
u
o Refit chimney section C to the hood and fix it onto the hood
using the two screws that are supplied.
o Secure the top of chimney section C to the fixing bracket, usi
ng
the screws provided
o Slide chimney section D inside of chimney section C. Then
secure the upper brac
ket to the wall, using the same method as
you have just used to secure the lower bracket.
3) Lift ch cure it to the fixing
1 imney section D up to the ceiling and se
racket using the screws provided.
b
22
Page 23
ompleting the installation
C
you are setting the appliance to recirculation mode, then you should
If
now fit the two carbon filters. S
ection on page 14.
s
The electrical connection must correspond to the electrical require
noted on the rating p
ppliance should now be connected to the electrical supply. See page
a
15 – 16 for detailed information on the electrical connection.
Use a stainless steel cleaner on the stainless steel sections of the
appliance.
Refit the grease filter and then switch on the mains su
to the appliance. Check that the appliance is operating
correctly by selecting each speed and switching the light
bulbs on and off.
late, which is placed inside the cooker hood. The
ee the “Fitting the carbon filters”
ment
pply
Extraction mode or recirculation mode?
What is the difference between extraction and recirculation
modes?
To get optimum performance from your cooker, the air will be taken
out of the
Unfortunately if you live in a flat or the hood is too far from an outsid
wall, this may not be possible. The only alternative is to recirculate the
ir.
a
In recirculation mode stale air is taken via the grease filter, and passed
ugh a charcoal filter for purification. The air then re-enters the
thro
itchen via an opening in the hood
k
What is a charcoal filter and do I need one?
ll cooker hoods have a grease filter but if you are using your cooker
A
hood in recirculation mode, then a charcoal filter m
ddition to the grease filter.
a
room via external ducting.
.
ust be fitted in
e
23
Page 24
roubleshooting
T
MPORTANT: If your cooker hood appears not to be operating
I
properly, before con
lease refer to the checklist below.
p
My cooker hood will not start.
o Ch ck that the hood is connected to th
o Check that the fan speed control is set correctly.
o Th fan speed is not set high enough
o The grease filters are dirty and require cleaning.
o The kitchen is not well ventilated enough.
o
o If the hood is set up for extraction mode, check that the duc
o Th safety cut-out device has been tripped.
o Turn off the hob and then wait for the safety cut-out device to
o IMPORTANT: If you have installed your cooker hood too low,
e e electricity supply
My cooker hood is not working effectively.
e
If the hood is set up for recirculation mode, check that the
carbon filters do not need replacing.
hose and discharge outlet are not blo
My cooker hood has switched off du
e
reset.
the saf
may become dama
frequently.
ety cut-out device will frequently trip. Your cooker hood
tacting the Baumatic Service Department,
cked.
ring operation.
ged if the safety cut-out device is tripped
ting
24
Page 25
IMPORTANT: If your appliance appears not to be
operating correctly, then you should disconnect it
from your mains supply and then contact the
Baumatic Service Department on telephone
number (0118) 933 6911.
DO NOT ATTEMPT TO REPAIR THE APPLIANC
E
YOURSELF.
Please note th t if an engineer is asked to attend whilst the product
under guarante at the problem is not the result of an
ppliance fault, then you may be liable for the cost of the call out
a
a is
e and finds th
charge.
The appliance must be accessible for the engineer to perfor
any nec
ay that an engineer is concerned that damage will be caused
w
essary repair. If your appliance is installed in such a
m
to the appliance or your kitchen, then he will not complete a
repair.
This includes situations where appliances have been tiled in,
sealed in
ont of the appliance, like plinths. Or any installation other
fr
with sealant, have wooden obstructions placed in
than the one specified by Baumatic Ltd. has been completed.
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance.
25
Page 26
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berksh
RG2 0QX
United Kingdom
Sales Tele
(0118) 933 6900
S
ales Fax
(0118) 931 0035
Service Telephon
(0118) 933
Service Fax
(0118) 986 9124
Spares Telephone
(01235) 4372
Technical Advice
(0118) 933 6933
E-mail:
sales@baumatic.co.uk
te
chnical@baumatic.co.uk
Website:
www.baumatic.co.uk
Republic o
01- 6266 798
ire
phone
e
6911
44
Telephone
f Ireland
Czech Republic
B
aumatic CR spol s.r.o.
A
mperova 495
4
6215, Librec
C
zech Republic
+420 800 185 263
www.baumatic.c
Slovak Republi
B
aumatic Slovakia, s.r.o.
Skultetyho 1
8
31 04 Bratislava 3
Slovakia
+421 255 640 618
Germany
Baumatic Gmbh
Janderstra
M
annheim, 68199
Germany
+4962 112
www.baumatic.d
Italy
B
aumatic Italia S.R.L.
Via Caltana 129
C
ampodarsego (Padova), 35011
Italy
+3904
www.baumatic.it
Holla
B
aumatic Benelux B.V.
Grindzuigerstraat 2
1
333 MS ALMERE
The Netherlands
+3136 54
www.baumatic.nl
sse 9
9920 2297
nd
9 1555
z
c
9190
e
2
26
Page 27
27
Page 28
28
Loading...