BT6.3GL/BT6.3BGL
BT7.3GL/BT7.3BGL
BT9.3GL/BT9.3BGL
BT10.3GL/BT10.3BGL
Glass chimney hood
User Manual for your Baumatic
BT6.3GL/BT6.3BGL
BT7.3GL/BT7.3BGL
BT9.3GL/BT9.3BGL
BT10.3GL/BT10.3BGL
Cooker Hood
Glass chimney hood
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
GS 23/08/13
2
Contents Page
Environmental note 4
IMPORTANT SAFETY INFORMATION 5 – 7
Specifications of your cooker hood 8 - 11
BT6.3GL / BT6.3BGL 8
BT7.3GL / BT7.3BGL 9
BT9.3GL / BT9.3BGL 10
BT10.3GL / BT10.3BGL 11
Using your Baumatic cooker hood 12 - 13
Before first use 12
To use your cooker hood 12 – 13
Cleaning your Baumatic cooker hood 13 – 14
Cleaning 13
The grease filter 14
Maintenance 14 - 16
Removing and cleaning the grease filter 14
Changing a light bulb 15
Fitting the carbon filters 16
Installation 17 - 26
Electrical connection 17 – 18
Before beginning installation 18 – 19
Installing your cooker hood 19 – 21
Connecting to external ducting 22
Fitting the chimney section 22 – 24
Attaching the glass canopy 25
Completing the installation 26
Extraction mode or recirculation mode? 26
Troubleshooting 27 – 28
Baumatic consumables 29
Contact details 30
3
ENVIRONMENTAL NOTE
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any
plug useless. Cut the cable off directly behind the appliance to
prevent misuse. This should be undertaken by a competent
person.
CONFORMITY TO W.E.E.E. DIRECTIVE
4
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of the information contained in
this booklet, please contact the Baumatic Customer
Care Department.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
o The hood must be installed in accordance with the installation
instructions and all measurements followed.
o If the cooker hood is installed for use above a gas appliance then
the provision for ventilation must be in accordance with the Gas
Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural
Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation &
Use) Regulations, the Building Regulations issued by the
Department of the Environment, the Building Standards
(Scotland) (Consolidated) Regulations issued by the Scottish
Development Department.
o It is dangerous to alter the specifications or to modify this
product in any way. Do not tamper with or attempt to modify
the appliance in any way.
o When installing the hood, ensure that the following
recommended distances are observed between the highest point
on the hob top (including the burners) and the bottom of the
cooker hood:
Electric cookers: 700 mm
Gas cookers: 700 mm
Coal/ oil cookers: 800 mm
IMPORTANT: DO NOT SET YOUR COOKER HOOD LESS
THAN 700mm ABOVE YOUR COOKER.
o When installed between adjoining wall cabinets, the cabinets
must not overhang the hob.
5
o The edges of the cooker hood are sharp – be mindful of this as
you handle your appliance, especially during installation and
cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTER!
o If the room where the cooker hood is to be used contains a fuel
burning appliance such as a central heating boiler then its flue
must be of the sealed or balanced flue type.
o If other types of flue or appliances are fitted, ensure that there is
an adequate supply of air in the room.
o When the hood is being used in extraction mode, ensure that the
ducting is fire retardant and that there are no bends greater
than 90 degrees as this will reduce the efficiency of the hood.
o Ensure the ducting for the extractor mode has the same
diameter as the outlet hole all the way through.
o Keep young children from using, playing with
or tampering with the cooker hood. Older
children and infirm persons should be
supervised if they are using the cooker hood.
o Your cooker hood is for domestic use only.
o Please dispose of the packing material carefully – children are
especially vulnerable to it.
o Dirty oil is an even greater fire risk.
o Always put lids on pots and pans when cooking
on a gas cooker.
o The manufacturer refuses to accept any responsibility for
damages arising to the hood or for it catching on fire, from a
failure to observe the fire safety advice contained in these
instructions.
6
o Remember that when in extraction mode, your cooker hood is
removing air from your room. Ensure that proper ventilation
measures are being observed.
o Note that the cooker hood removes odours from your
kitchen, not steam.
o Warning - Always ensure that the cooker
hood has been disconnected from the
power supply before carrying out any work
on the hood, including cleaning and
replacing light bulbs.
o Do not connect the ducting system of this appliance to an
existing ventilation system being used for any other purpose.
o Do not install above a cooker with a high level grill.
o Never leave frying pans unattended during use
as overheated fats and oils might catch fire.
o The cooker hood should not be exposed to a direct heat source
from the cooking device underneath it, i.e. naked flame from a
gas burner or heat from electric hob zones without a pan on
them.
o Do not attempt to use the cooker hood if it is damaged in any
way. Never attempt to use it without the grease filter fitted or if
the filter is excessively greasy!
o Never flambé cook under this cooker hood.
o The lights on this appliance should only be used during operation
of the cooker hood. They should not be left on permanently and
used as a lighting source. THE LIGHTS ON THIS APPLIANCE ARE
NOT INTENDED FOR ROOM ILLUMINATION.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY IN THE EVENT OF FAILURE
TO OBSERVE THE INSTRUCTIONS GIVEN
HERE, FOR INSTALLATION, MAINTENANCE
AND SUITABLE USE OF THE HO
OD.
7
Specifications of your cooker hood
BT6.3GL / BT6.3BGL
Dimensions:
Width (canopy): 600 mm
Height (with chimney): 583 – 1063 mm
Depth (canopy): 500 mm
Dimensions of the chimney section:
303 mm x 276 mm
Specifications:
o High extraction tangential motor
o Pushbutton control operation
o 3 Speeds
o 1 x Washable metallic grease filter
o 2 x Halogen lights
o Extraction capacity:
o Noise level min/max: 61 – 66 dB
o Optional Extra
for air recirculation mode
(available from the Baumatic
Spares Department).
: 1 x S1 pair of carbon filters
500 m³/hr
8
BT7.3GL / BT7.3BGL
Dimensions:
Width (canopy): 700 mm
Height (with chimney): 583 – 1063 mm
Depth (canopy): 500 mm
Dimensions of the chimney section:
303 mm x 276 mm
Specifications:
o High extraction tangential motor
o Pushbutton control operation
o 3 Speeds
o 1 x Washable metallic grease filter
o 2 x Halogen lights
o Extraction capacity:
o Noise level min/max: 61 – 66 dB
o Optional Extra: 1 x S1 pair of carbon filters
for air recirculation mode
(available from the Baumatic
Spares Department).
500 m³/hr
9
BT9.3GL / BT9.3BGL
Dimensions:
Width (canopy): 900 mm
Height (with chimney): 583 – 1063 mm
Depth (canopy): 500 mm
Dimensions of the chimney section:
303 mm x 276 mm
Specifications:
o High extraction tangential motor
o Pushbutton control operation
o 3 Speeds
o 2 x Washable metallic grease filters
o 2 x Halogen lights
o Extraction capacity:
o Noise level min/max:
o Optional Extra: 1 x S1 pair of carbon filters
for air recirculation mode
(available from the Baumatic
Spares Department).
500 m³/hr
61 – 66 dB
10
BT10.3GL / BT10.3BGL
Dimensions:
Width (canopy): 1000 mm
Height (with chimney): 593 – 1073 mm
Depth (canopy): 500 mm
Dimensions of the chimney section:
303 mm x 276 mm
Specifications:
o High extraction tangential motor
o Pushbutton control operation
o 3 Speeds
o 2 x Washable metallic grease filters
o 2 x Halogen lights
o Extraction capacity: 500 m³/hr
o Noise level min/max: 54 – 62 dB
o Optional Extra
for air recirculation mode
(available from the Baumatic
Spares Department).
: 1 x S1 pair of carbon filters
11
Using your Baumatic cooker hood
Before first use
IMPORTANT: THIS PROCESS MUST BE FOLLOWED BEFORE
THE COOKER HOOD IS USED FOR THE FIRST TIME.
o You should use a good quality stainless steel cleaner on ALL of
the stainless steel areas of your cooker hood, before it is used
for the first time.
o This will help to leave a silicone water-resistant film to protect
the stainless steel surfaces.
To use your cooker hood
o Make sure that it has been installed by a suitably qualified
person, as per the information contained in Baumatic’s
installation instructions.
o Find the control panel, which is located at the front right of the
canopy.
o There are several buttons on the control panel, which perform
separate functions.
o A = Speed selection buttons
= Low speed
= Medium speed
= High speed
o B = Light on/off button
12
IMPORTANT: IDEALLY YOU SHOULD TURN ON YOUR
HOOD TEN MINUTES BEFORE YOU START TO COOK,
OR AT THE VERY LEAST WHEN YOU BEGIN COOKING.
YOU SHOULD ALSO RUN YOUR HOOD FOR TEN
MINUTES AFTER YOU HAVE FINISHED COOKING.
Cleaning your Baumatic cooker hood
IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE
THAT YOU HAVE SWITCHED YOUR COOKER HOOD
OFF AT THE OMNI-POLAR SWITCH, SET AT THE
WALL FROM THE CABLE.
Cleaning
o Clean the external parts of your cooker hood with mild liquid
detergent and a new damp cloth.
o Never use abrasive powder, corrosive solvents or brushes.
o Never insert pointed objects into the motor’s protective grid.
o Only clean the control panel and grease filter grill with mild liquid
detergents and a new damp cloth.
o If you are using the appliance in recirculation mode, then be
sure to replace the carbon filters at the recommended interval
(see section on “Fitting the carbon filter”). A build up of grease
could cause a fire hazard.
o Never attempt to clean the area above the grease filter.
o IMPORTANT: You should regularly use a good quality
stainless steel cleaner to maintain the shine and finish on
the stainless steel areas of your cooker hood.
o This will help to leave a silicone water-resistant film to protect
the stainless steel surfaces and keep them in good condition for
the life of the product.
13
The grease filter
o Your cooker hood includes a grease filter which helps to absorb
grease particles to protect your kitchen & furniture from greasy
residues.
o The metallic filter may become flammable if it becomes
saturated with this greasy residue.
o To prevent this fire hazard, the filter should be cleaned regularly.
Depending on use, this should be done every 10-15 days or at
least once a month, using hot water and normal washing-up
detergent.
o DO NOT WASH THE GREASE FILTER IN A DISHWASHER.
Maintenance
Removing and cleaning the grease filter
o First remove the grease filter by
pulling down on the handle, and then
pull it away from the main body of the
cooker hood.
o Soak the grease filter in hot water and
washing up liquid for about an hour.
o Rinse it off thoroughly with hot water.
o Repeat the process if required.
o Refit the grease filter once it has dried.
o IMPORTANT: Let the grease filter dry thoroughly before
refitting it in the cooker hood.
14
Changing a light bulb
IMPORTANT: BEFORE ATTEMPTING TO CHANGE A
LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE
DISCONNECTED THE COOKER HOOD FROM YOUR
MAINS SUPPLY.
o Prior to touching the light bulbs ensure that they have cooled
down.
o Find the bulb that requires
replacement. You will find it
located in the light fixture which is
located under the canopy.
o Use a screwdriver to remove the
glass cover that sits over the bulb.
o Insert the screwdriver into the
slots around the bracket
surrounding the glass.
o Apply a little pressure to
lever out the lighting cover
from the securing clips and
then pry away from the
fixture.
o Remove the light bulb that needs to
be replaced and insert a new G4
20W (max) bulb. Then replace the
glass cover.
o IMPORTANT: Defective bulbs should be replaced immediately.
o If the lights still do not work, make sure that the bulbs are fitted
properly into their housings before you call for technical
assistance.
15
Fitting the carbon filter
If the appliance is going to be used in recirculation mode then it is
necessary to fit carbon filters. This will help to absorb unpleasant
odours caused by cooking.
IMPORTANT: BEFORE ATTEMPTING TO FIT OR
REMOVE THE CARBON FILTERS, YOU MUST
ENSURE THAT YOU HAVE DISCONNECTED THE
COOKER HOOD FROM YOUR MAINS SUPPLY.
1) Remove the grease filter.
2) Hook the carbon filter over
the pins that are located at the
end of the motor.
3) Turn the carbon filter anticlockwise, until you feel
it click into place.
o Repeat this process for the second carbon filter. You need to
place a carbon filter at either end of the motor.
o Refit the grease filter.
o The carbon filters should be replaced every three months, or if
they show signs of damage.
16
Installation
IMPORTANT: Before installation and usage read
all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
the rating plate are exactly the same as the
voltage and frequency in your home. The rating
plate can be found behind the grease filter.
The manufacturer declines all responsibility in the event of the installer
failing to observe all the accident prevention regulations in force,
which are necessary for normal use and the regular operation of the
electric system.
Electrical connection
YOUR COOKER HOOD IS INTENDED FOR FITTED AND
PERMANENT INSTALLATION.
o The cooker hood’s power cable must be fitted upstream from the
electrical connection, using an omni-polar switch with a contact
distance of at least 3 mm. THE FUSE MUST BE RATED AT 3
AMPS.
WARNING: THIS APPLIANCE MUST BE EARTHED. It should
only be connected by a competent person, using fixed wiring
via a double pole switched fused spur outlet.
We recommend that the appliance is connected by a qualified
electrician, who is a member of the N.I.C.E.I.C. and who will comply
with the I.E.E. and local regulations. The wires in the mains lead are
coloured in accordance with the following UK code:
Blue = Neutral, Brown = Live, Green/Yellow = Ground
If you only find two wires in the main’s lead (blue and brown),
then neither must be connected to the earth terminal.
o As the colours of the wires in the appliance’s mains lead may not
correspond with the coloured markings identifying the terminals
in your spur box, please proceed as follows:
(UK ONLY).
17
o The blue wire must be connected to the
terminal marked “N” (neutral), or coloured
black.
o The brown wire must be connected to the
terminal marked “L” (live), or coloured red.
Before beginning installation
o Check that the product purchased is of a suitable size for the
chosen installation area. In addition check whether there is an
electrical socket available that will be accessible once the hood is
mounted. If the product is going to be used in extraction mode,
then there should also be space to connect a ducting hose to the
outside.
o Carry out all necessary masonry work prior to the fitting of the
cooker hood.
o Ensure that all electrical connections are carried out by a suitably
qualified person.
o Before commencing installation of the cooker hood the grease filter
should be removed.
o Check inside the product and ensure that there is no transit
packaging or any other materials, such as packets of screws,
guarantees etc. These should be removed and kept for future use.
o If possible, disconnect and move freestanding or slot-in cookers
from their position, to provide easier access to the rear wall and
ceiling. If this is not possible, then a thick, protective covering
should be placed over the worktop, hob top or cooker. This will help
to protect these surfaces from damage and debris.
o Select a flat surface for assembling the cooker hood. Cover that
surface with a protective covering and place all cooker hood parts
and fittings on it.
o Rawl plugs are provided to secure the hood to most types of walls
and ceilings. However a qualified technician must verify the
suitability of the materials, in accordance with the type of wall and
ceiling. The wall and ceiling must be strong enough to take the
weight of the hood.
o Do not tile, grout or silicone this appliance to the wall. This
appliance is designed to be surface mounted only.
18
Installing your cooker hood
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
INSTALLING YOUR COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
MODE. PLEASE TURN TO PAGE 26 NOW TO
UNDERSTAND THE DIFFERENCES BETWEEN THESE
TWO MODES.
o We recommend that at least two people install this hood.
IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO
YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION
PROCESS HAS BEEN COMPLETED.
1) Remove the metal grease filter.
2) Position the hood against the wall that you are intending to
install it on and mark the position of the support holes that are
to be drilled (as shown in the figure below).
19
2a) The support screw holes are indicated by figure A in this drawing
and the anchoring screw holes are indicated by figure B.
3) Using a drill bit with an 8 mm
diameter, make holes in the wall on the
positions that you have marked in step
2.
4) Insert rawl plugs into all of the holes that you have drilled.
5) Fasten the support screws halfway in, leaving them 10 mm out of
the wall.
20
6) Hang the hood onto the support
screws.
7) Fully tighten the support screws (A) and then screw the anchoring
screws (B) through the relevant holes in the cooker hood. Tighten the
anchoring screws fully into the wall.
21
Connecting to external ducting
8) Connect the coupling to the top of the cooker hood, and then
connect a 125 mm ducting hose to the coupling (please note that
the ducting hose is not supplied with the appliance).
o The other end of the ducting hose should be connected to a
discharge outlet that is suitable for cooking vapours. It should
have a cross section of at least 150 cm².
o The maximum distance between the coupling and your discharge
outlet should be 3 metres, with one 90 degree bend.
Fitting the chimney
9) Take the two chimney
sections (C and D).
o Rest the bottom of
chimney section C on the
top of the hood. You
should take care to
position the tabs on the
chimney section into the
rear of the hood.
o Mark the side
measurement of both
sides of chimney section C
on the wall with a pencil.
22
10) Lift chimney section D upwards until it reaches the ceiling. You
must ensure that it is perpendicular to the hood.
o Mark the side measurements of both sides of chimney section D
on the wall with a pencil and then remove chimney section D.
11) Take the fixing bracket (E) and place it between the two pencil
marks that you made in step 9.
o Keeping the bracket in contact with the wall, use a pencil to
mark on the wall the anchoring holes that are cut out of the
bracket
23
12) Using an 8 mm drill bit, drill out two holes on the pencil markings
that you made in step 11. Insert rawl plugs into the holes and then
use a screwdriver to secure the fixing bracket to the wall.
o Refit chimney section C to the hood and fix it onto the hood
using the two screws that are supplied.
o Secure the top of chimney section C to the fixing bracket, using
the screws provided.
o Slide chimney section D inside of chimney section C. Then
secure the upper bracket to the wall, using the same method as
you have just used to secure the lower bracket.
13) Lift chimney section D up to the ceiling and secure it to the fixing
bracket using the screws provided.
24
Attaching the glass canopy
o The anchoring bolts (F) should be found with the other brackets
and screws provided with the cooker hood. If you find them
already attached to the cooker hood, then you should unscrew
them.
o Carefully place the glass section (Q) on the upper surface of the
cooker hood and then slide it back towards the wall.
o Screw the anchoring bolts (F) through the relevant holes in the
glass section (Q).
o IMPORTANT: You must ensure that the glass section is securely
held in place by the anchoring bolts. However the anchoring
bolts must not be over tightened, otherwise excessive pressure
could be placed on the glass section.
25
Completing the installation
If you are setting the appliance to recirculation mode, then you should
now fit the two carbon filters. See the “Fitting the carbon filters”
section on pages 16.
The electrical connection must correspond to the electrical requirement
noted on the rating plate, which is placed inside the cooker hood. The
appliance should now be connected to the electrical supply. See pages
17 – 18 for detailed information on the electrical connection.
Use a stainless steel cleaner on the stainless steel sections of the
appliance.
Refit the grease filter and then switch on the mains supply
to the appliance. Check that the appliance is operating
correctly by selecting each speed and switching the light
bulbs on and off.
Extraction mode or recirculation mode?
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
INSTALLING YOUR COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
MODE.
What is the difference between extraction and recirculation
modes?
In extraction mode, the stale air will be taken via the grease filter and
out of the room via external ducting.
In recirculation mode stale air is taken via the grease filter, and passed
through charcoal filters for purification. The air then re-enters the
kitchen via an opening in the hood
.
For optimum performance, we recommend that the cooker hood is
used in extraction mode and connected to external ducting.
Unfortunately if you live in a flat or the hood is too far from an outside
wall, this may not be possible. The only alternative is to recirculate the
air.
Do I need a charcoal filter?
All cooker hoods have a grease filter but if you are using your cooker
hood in recirculation mode, then a charcoal filters must be fitted in
addition to the grease filter.
26
Troubleshooting
IMPORTANT: If your cooker hood appears not to be
operating properly, before contacting the Baumatic
Customer Care Department, please refer to the
checklist below.
My cooker hood will not start.
o Check that the hood is connected to the electricity supply
o Check that the fan speed control is set correctly.
My cooker hood is not working effectively.
o The fan speed is not set high enough
o The grease filter is dirty and requires cleaning.
o The kitchen is not well ventilated enough.
o If the hood is set up for recirculation mode, check that the
carbon filters do not need replacing.
o If the hood is set up for extraction mode, check that the ducting
hose and discharge outlet are not blocked.
My cooker hood has switched off during operation.
o The safety cut-out device has been tripped.
o Turn off the hob and then wait for the safety cut-out device to
reset.
o IMPORTANT: If you have installed your cooker hood too low,
the safety cut-out device will frequently trip. Your cooker hood
may become damaged if the safety cut-out device is tripped
frequently.
27
IMPORTANT: If your appliance appears not to be
operating correctly, then you should disconnect it
from your mains supply and then contact the
Baumatic Customer Care Department on
telephone number (0118) 9
DO NOT ATTEMPT TO REPAIR THE APPLIANCE
YOURSELF.
Please note that if an engineer is asked to attend whilst the product is
under guarantee and finds that the problem is not the result of an
appliance fault, then you may be liable for the cost of the call out
charge.
The appliance must be accessible for the engineer to perform
any necessary repair. If your appliance is installed in such a
way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then they will not complete a
repair.
This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance, like plinths. Or any installation other
than the one specified by Baumatic Ltd. has been completed.
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance when it is delivered.
33 6911.
28
Baumatic Consumables
o BC001 Degreaser for Dishwashers (200 g)
o BC002 Descaler for Washing Machines and Dishwashers (200 g)
o BC003 Ceramic Hob Cleaner (250 ml)
o BC004 Oven Cleaner (250 ml)
o BC005 Stainless Steel Cleaner and Protector (250 ml)
o BC007 E-Cloth – General Purpose Cloth
o BC008 Microwave Cover
To order a Baumatic consumable product please call 0123 5437 244
and quote the product code. You can also order online from
eshop.baumatic.co.uk
29
United Kingdom
Baumat
Baumat
6 Bennet Road,
Readin
RG2 0Q
United
Sales Telephone
(01
Sales Fax
(0118) 931 0035
Customer Care Telephone
(01
Customer Care Fax
(01
Spares Telephone
(01235) 437244
Advice Line Telephone
(01
E-mail:
sale
customercare@baumatic.co.uk
spares@baumatic.co.uk
technical@baumatic.co.uk
Website:
www.baumatic.
Facebook:
www.facebook.com/baumatic.uk
Republic of Ireland
Service Telephone
1
-890 812 724
Spares Telephone
091 756 771
ic Ltd.,
ic Buildings,
g, Berkshire
X
Kingdom
18) 933 6900
18) 933 6911
18) 986 9124
18) 933 6933
s@baumatic.co.uk
co.uk
Czech Re
Baumat
Lípov
46
0 01 Liberec 4
Czech
Panens
1 03 Bratislava - Staré Mesto
81
Slova
0 483 577 200 (CZ)
+42
1 255 640 618 (SK)
+42
www.baumatic.
www.baumatic.
Germa
public/Slovakia
ic s.r.o.
á 665/1
Republic
ká 34
kia
cz
sk
ny
Kundendienst & Ersatzteile
Deutschland 0049(0)180-5888975
Oesterreich +43 (0) 820 / 420423
www.baumatic.de
Italy
Baumat
Via Ga
35
+3
www.baumatic.it
Holland
Baumat
Dukdal
13
Nederland
+31(
www.baumatic.nl
ic Italia S.R.L.
lvani N.3
011 Campodarsego (PD)
904 9920 2297
ic Benelux B.V.
fweg 15d
32 BH ALMERE
0)36 549 1553/1555
30
31
32
Loading...