BP95S
COD. 208398-00 - 12.06.2012
INSTRUCTIONS FOR THE INSTALLATION AND USE
OF BUILT-IN &22.723
MODEL: BP64S
MODEL: BP75S
MODEL: BP95S
Baumatic
Dear Customer,
Congratulations on purchasing your new product from Think Appliances.
To register your parts and labour warranty (some conditions apply please refer to
your warranty card for more details) please contact out Customer Care team on:
1800 444 357
Our Customer Care centre is there to ensure you get the most out of your
appliance. For example, should you want to learn more about recommended
cooking temperatures, the various cooking functions available, how to set and
program your LED clock, and importantly taking care of your appliance when
cleaning, please call us because we are here to help you.
It is important that you read through the following use and care manual thoroughly
to familiarize yourself with the installation and operation requirements of your
appliance to ensure optimum performance.
We also carry a complete range of spare parts for all Think products. For all your
spare parts enquiries please contact our team at Pronto Parts on:
1300 306 973
Again, thank you for choosing an appliance brought to you by Think Appliances and
we look forward to being of service to you.
Kind regards
Management
Think Appliances
3
GENERAL NOTICE
We invite you to read this instruction booklet carefully, before installing and using the equipment.
It is very important that you keep this booklet together with the equipment for any future
consultation.
If this equipment should be sold or transferred to another person, make sure that the new
user receives the booklet, so that they can learn how to operate the appliance and read the
corresponding notice.
This is a Class 3 appliance.
This appliance complies with the following Directives:
EEC 2009/142/CE (Gas) EEC 2004/108/CE (Electromagnetic Compatibility)
EEC 2006/95/CE (Low Voltage) EEC 89/109 (Contact with foods)
WARNING
– The installation must be carried out by authorised personnel, in conformity with the regulations in force.
– CAUTION: The surface temperature of underbench components exceeds 95°C. To avoid a hazard,
underbench access must be restricted. Refer to the installation instructions.
– This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
– Children should be supervised to ensure that they do not play with the appliance.
– Before powering the equipment, check that it is properly adjusted for the type of gas at disposal (see the
“installation” paragraph).
– If the supply cord is damaged it must be replaced by a special cord or assembly available from the
manufacturer or its service agent.
– Before carrying out the maintenance or cleaning the equipment, cut off power supply and allow it cool
down.
– Make sure that air circulates around the gas equipment. Insufficient ventilation produces a lack of oxygen.
– In case of an intense or prolonged use of the equipment, it may be necessary to improve aeration, for
example by opening a window or increasing rangehood venting power, if it exists.
– The products of combustion must be discharged outside through a suction hood or an electric fan (see
the “installation” paragraph).
– For any possible operation or modification, apply to an authorized Technical Assistance Centre and
demand original spare parts.
– Where this appliance is installed in marine craft or in caravans, it shall not be used as a space heater.
– Not for use in marine craft, caravans or mobile homes unless each burner is fitted with a flame safeguard.
– Do not spray aerosols in the vicinity of the appliance while it is in operation.
– Do not store or use flammable materials or items in the vicinity of this appliance.
DO NOT MODIFY THIS APPLIANCE.
Servicing shall be carried out only by authorised personnel.
The product label, with the serial number, is fixed to the underside of FRRNWRS.
An additional label should be adhered to adjacent cabinetry for easy access- refer installation
instructions.
The manufacturer refuses all responsibility for possible damages to things or people, resulting
from incorrect installation or from an improper, incorrect or unreasonable use of this equipment.
4
It is necessary that all the operations regarding the installation, adjustment and
adaptation to the type of gas available are carried out by authorised personnel, in
conformity with the regulations in force. The specific instructions are described in the
booklet section intended for the installer.
Conditions of Use.
This appliance is intended to be used IRUGRPHVWLFKRXVHKROGXVHRQO\
7KLVDSSOLDQFHVLVQRWWREHXVHGIRUFRPPHUFLDOSXUSRVHV
INSTRUCTIONS FOR THE USER
USING THE BURNERS
The silk-screen V\PEROVprinted on the side of the
knob indicate the correspondence between the
knob and the burner.
Automatic start-up with valves
Turn the corresponding knob anticlockwise up
to the maximum position (large flame, fig. 1) and
press the knob.
Once the burner has been started up, keep the
knob pressed for about 6 seconds.
ATTENTION: the triple ring burner switches on
only RQ the maximum flame position
Using the burners
In order to obtain the maximum yield without
waste of gas, it is important that the diameter of
the pot is suitable for the burner potential (see the
following table), so as to avoid that the flame going
out (fig. 2SDJH).
Use the maximum capacity to quickly make
liquids reach boiling temperature, and the reduced
capacity to heat food or maintain boiling. All of the
operating positions must be chosen between the
maximum and the minimum ones, never between
the minimum position and the closing point.
The gas supply can be interrupted by turning
the knob clockwise up to the closing position. If
there is no power supply, it is possible to light the
burners with matches, setting the knob to the start-
up point (large flame, fig. 1SDJH).
BURNERS
Power (MJ/h)
Ø of
cookware (*)
NG LPG
Auxiliary 3,4 3,4 10 - 14 cm
Semi-rapid 6,3 5,6 16 - 18 cm
Rapid 11,5 9,6 20 - 22 cm
Triple crown 13,0 12,0 24 - 26 cm
Double crown 10,3 9,6 24 - 26 cm
(*) For cookware with diameter 120mm or
below use mini-trivet supplied, refer fitment
instructions on page 13.
It is important to use cookware with the sizes
specified and ensure the cookware is always
correctly centred over the burner. Using
oversize cookware can potentially cause heat
damage to your benchtop and/or control knobs
which will not be covered under warranty.
Notice
– When the equipment is not working, always
check that the knobs are in the closing position
(see fig.1SDJH).
– If the flame should blow out accidentally, the
safety valve will automatically stop the gas
supply, after a few seconds. To restore operation,
set the knob to the lighting point (large flame, fig.
1) and press.
– While cooking with fat or oil, pay the utmost
attention as these substances can catch fire
when overheated.
– Do not place unstable or deformed pots on the
burner, so as to prevent them from overturning or
overflowing.
– Handles should be turned away from the front of
the bench to avoid accidents.
– When the burner is started up, check that the
flame is regular and, before taking pots away,
always lower the flame or put it out.
5
INSTRUCTIONS FOR THE USER
1 Burner
2 Flame safeguard sensor (where fitted)
3 Injector
4 Ignition spark plug
If you have a problem with the cooktop, check the table below. You may be able to solve the problem and
this will save you from paying for a service call. You will have to pay for a service call even in the warranty
period if the problem is one listed below
FAULT POSSIBLE CAUSES REMEDY
Burner will not light
even though the LJQLWLRQ
VSDUNis working.
Knob not held down long enough in
‘High’ position for flame safeguard
(where fitted) to engage
Repeat lighting procedure and hold knob
down for 6 seconds in ‘High’ position (refer
page 3)
Gas supply valve turned off Turn on gas supply to appliance
Wrong knob turned Ensure the knob you are turning
corresponds to the burner you want to light
%lockage in ignition area Ensure that ports in ignition area are clean
and dry
Ignition spark plugs wet or dirty Dry or clean ignition spark plugs
No spark is obtained
when control knob is
activated
Electricity supply is disconnected or
switched off"
Switch on electricity or check fuses
Ignition spark plugs wet or dirty Dry or clean ignition spark plugs
Flames uneven or
tending to lift
Flame ports blocked or wet Clean or dry flame ports
Burner incorrectly fitted Ensure this component is fitted correctly
Flames not staying on
when knob released
Knob not held down long enough
in ‘High’ position for flame safeguard
(where fitted) to engage
Repeat lighting procedure and hold knob
down for 6 seconds in ‘High’ position
(refer page 3)
Knob not set between ‘High’ and
‘Low’
Knob MUST be set between these
positions
Dirt or spillage on flame safeguard
sensor (where fitted)
Clean flame safe guard sensor tip
Low heat, slow
cooking
Incorrect cooking pot or pan being
used
Refer to table page 3
Benchtop or knobs
overheating
Incorrect cooking pot or pan used Check table on page 3 for correct pot or
pan to be used
Pot or pan not located on burner
properly
Ensure pot or pan is centrally located
on burner
If the above points have been checked and there is still a problem with the cooktop, please call the Service
Centre.
Loading...