Page 1
BO616SS 60 cm Built in fan oven
BO628SS 60 cm Built in
multifunction oven
BO636SS / R/ W 60 cm Built in
multifunction oven
1lxa,
Page 2
User Manual for your Baumatic
BO616SS 60 cm Built in fan oven
BO628SS 60 cm Built in multifunction oven
BO636SS/R/W 60 cm Built in
multifunction oven
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
DD 22/02/12
2
Page 3
Contents
Environmental note 4
Important safety information 5 – 7
Specifications 8 – 12
BO616SS 8 - 9
BO628SS 9 - 10
BO636SS/R /W 10 - 11
Cooling fan 11
Control panel 11
Oven programmer/timer 12
Initial set up of your oven 12 – 13
Setting the time of day 12
Before first use 13
Timer functions 14 – 19
The minute minder function 14
The semi-automatic cooking function 15
The end of cooking function 16
The automatic cooking function 17 – 18
Cancelling the semi-automatic and automatic function 18
Cancelling the minute minder function 18
Adjusting the volume of the audible signal 18
Changing the time of day 19
Using your oven 19 - 22
Selecting an oven function 19 - 20
Thermostat control knob 20
Oven operating light 21
Cooking guidelines 21 - 22
Warnings 22
Cleaning and maintenance 23 - 27
Replacing the oven bulb 24
Removing the oven door for cleaning 25
Removing the inner door glass for cleaning 26 - 27
Installation 27 - 31
Electrical connection 27 - 28
Positioning the appliance 29
Ventilation requirements 30
Installing the oven into the housing unit 31
My appliance isn’t working correctly 32 – 33
Baumatic consumables 34
Contact details 35
3
Page 4
Environmental note
o The packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
o Please discard all packaging material with due regard for the
environment.
4
Page 5
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
booklet, please contact the Baumatic Customer Care
Department.
General Information
o This appliance is designed for domestic household use and can
be built into a standard kitchen cabinet or housing unit.
o IMPORTANT: The adjacent furniture or housing and all
materials used in the installation must be able to withstand a
minimum temperature of 85°C above the ambient temperature
of the room it is located in, whilst in use.
o Certain types of vinyl or laminate kitchen furniture are
particularly prone to heat damage or discolouration at
temperatures below the guidelines given above.
o Any damage caused by the appliance being installed in
contravention of this temperature limit, or by placing adjacent
cabinet materials closer than 4mm to the appliance, will be the
liability of the owner.
o The use of this appliance for any other purpose or in any other
environment without the express agreement of Baumatic Ltd.
will invalidate any warranty or liability claim.
o Your new appliance is guaranteed against electrical or
mechanical defects, subject to certain exclusions that are noted
in Baumatic’s Conditions Of Guarantee. The foregoing does not
affect your statutory rights.
o Repairs may only be carried out by Baumatic service
engineers or their authorised service agent.
Warning and safety instructions
o This appliance complies with all current European safety
legislation. Baumatic do wish to emphasise that this compliance
does not remove the fact that the appliance surfaces will
become hot during use and retain heat after operation.
5
Page 6
Child Safety
o Baumatic strongly recommend that babies and young children
are prevented from being near to the appliance and not allowed
to touch the appliance at any time.
o If it is necessary for younger family members to be in the
kitchen, please ensure that they are kept under close supervision
at all times.
General Safety
o Do not place heavy objects on the oven door or lean on the
oven door when it is open, as this can cause damage to the oven
door hinges.
o Do not leave heated oil or fat unattended, as this is a fire risk.
o Do not place pans or baking trays directly on the base of the
oven cavity, or line it with aluminium foil.
o Do not allow electrical fittings or cables to come into contact
with areas on the appliance that get hot.
o Do not use the appliance to heat the room it is located in or to
dry clothing.
o Do not install the appliance next to curtains or soft furnishings.
o Do not attempt to lift or move cooking appliances by using the
oven door or handle, as this may cause damage to the appliance
or result in injury to the person lifting the appliance.
Cleaning
o Cleaning of the oven should be carried out on a regular basis.
o Great care should be taken whilst using this appliance and when
following the cleaning procedure.
o IMPORTANT: The appliance must be disconnected from the
mains before following the cleaning procedure.
6
Page 7
Installation
This appliance must be correctly installed by a
suitably qualified person, strictly in accordance
with the manufacturer’s instructions.
o Baumatic Ltd. declines any responsibility for injury or
damage, to person or property, as a result of improper
use or installation of this appliance.
o Heat, steam and moisture will be created during use of the
appliance, take care to avoid injury and ensure that the room is
adequately ventilated. If the appliance is going to be used for
prolonged periods of time, then additional ventilation may be
required.
o Please consult with your qualified installer if you are in any doubt
about the amount of ventilation that you will require.
Declaration of conformity.
This appliance complies with the following European Directives:
- 2006/95/EC regarding “low voltage”
- 2004/108/EC regarding “electromagnetic disturbances”#
- Regulation (EC) N° 1935/2004 regarding “materials in contact
with food”
o The above directives comply with 93/68/EEC regarding CE
marking.
o The manufacturer declares that the oven is built using certified
materials and requires the appliance to be installed in
accordance with the standards currently in force. This appliance
must be used by a trained person for domestic purposes only.
7
Page 8
Specifications
BO616SS
Product Dimensions
Height: 600 mm
Width: 598 mm
Depth: 565.5 mm
Aperture Dimensions
Height: 583 mm – 585
mm
Width: 560 mm
Depth: 560 mm
Product specifications
o 4 function fan oven
o Energy efficiency class: A
o Oven capacity (net): 61 litres
o Oven capacity (gross): 68 litres
o LED full programmer
o Oven light
o Cooling fan
o Thermostatically controlled grill
o Double-glazed removable door
o Removable inner door glass
Standard accessories
o Enamelled baking tray with handle
o Safety shelf
o Trivet
Optional extra
o BPS2 Pizza stone
Electrical details
Rated Voltage: 220 - 240 V~ 50/60 Hz
Supply Connection: 13 A (double pole switched fused
outlet with 3mm contact gap)
Max Rated Inputs: 1.70 – 1.95 kW
Mains Supply Lead: 3 x 1.5mm²
8
Page 9
BO628SS
Product Dimensions
Height: 600 mm
Width: 598 mm
Depth: 565.5 mm
Aperture Dimensions
Height: 583 mm – 585
mm
Width: 560 mm
Depth: 560 mm
Product specifications
o 5 function multifunction oven
o Energy efficiency class: A
o Oven capacity (net): 61 litres
o Oven capacity (gross): 68 litres
o LED full programmer
o Oven light
o Cooling fan
o Thermostatically controlled grill
o Double-glazed removable door
o Removable inner door glass
Standard accessories
o 2 x Enamelled baking tray
o Safety shelf
Optional extra
o BPS2 Pizza stone
Electrical details
Rated Voltage: 220 - 240 V~ 50/60 Hz
Supply Connection: 13 A (double pole switched fused
outlet with 3mm contact gap)
Max Rated Inputs: 1.95 – 2.30 kW
Mains Supply Lead: 3 x 1.5mm²
9
Page 10
BO636SS/R/W
Product Dimensions
Height: 600 mm
Width: 598 mm
Depth: 565.5 mm
Aperture Dimensions
Height: 583 mm – 585
mm
Width: 560 mm
Depth: 560 mm
Product specifications
o 7 function multifunction oven
o Energy efficiency class: A
o Oven capacity (net): 61 litres
o Oven capacity (gross): 68 litres
o LED full programmer
o Oven light
o Cooling fan
o Thermostatically controlled grill
o Double-glazed removable door
o Removable inner door glass
Standard accessories
o Enamelled baking tray with handle
o Safety shelf
o Trivet
Optional extra
o BPS2 Pizza stone
Electrical details
Rated Voltage: 220 - 240 V~ 50/60 Hz
Supply Connection: 13 A (double pole switched fused
outlet with 3mm contact gap)
Max Rated Inputs: 2.15 – 2.55 kW
Mains Supply Lead: 3 x 1.5mm²
10
Page 11
Cooling fan
o A tangential cooling fan is fitted inside of these appliances, to
make the internal temperature of the oven stable and the
external surface temperature lower.
o After you have finished cooking and switched off the oven, the
cooling fan will continue to run for a period of time afterwards.
The length of time will depend on how long the oven has been
switched on for and at how high a temperature.
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate for your oven can be
located by opening the oven door and looking on the right hand side of
the oven chassis.
Model Number ……………………………….
Serial Number ……………………………….
Date of Purchase ……………………………….
Control Panel
1) Oven function selector knob
2) Thermostat control knob
3) Power indicator light
4) Oven operating light
5) LED display
6) Oven programmer/timer
11
Page 12
Oven programmer/timer
1 = Automatic cooking symbol
2 = Oven in use symbol
3 = Decimal point symbol
4 = Minute minder symbol
5 = Minus button
6 = Programme button
7 = Plus button
Initial set-up of your oven
Setting the time of day
After your appliance is connected to your mains supply for the first
time, you must set the time of day before you can use the oven.
o When the oven is connected to your mains supply for the first
time (or after a power cut), the digits on the LED display and
the automatic cooking symbol (1) will flash.
o Press and hold down the programme button (6) for a couple of
seconds. The automatic cooking symbol will go out and the
digits will remain steady.
o Whilst the decimal point symbol (3) is flashing, use the plus (7)
and minus (5) buttons to set the correct time of day.
o When the correct time of day is shown on the LED display,
release the plus and minus buttons and wait a few seconds. The
decimal point symbol will stop flashing and the oven is ready to
use.
12
Page 13
Before first use
o To remove any residue from the oven that may have been left
from the manufacturing process, you should select the fan oven
function (conventional oven for BO628SS) and set the
thermostat to its maximum temperature setting.
o It is perfectly normal for a smell to be produced during this
process.
o You should make sure that any windows in the room are left
open during this process.
o It is advisable for you not to remain in the room whilst the
burning off process is taking place.
o You should leave the oven on maximum setting for 30 – 40
minutes.
o After the oven cavity has cooled, it should then be cleaned with
warm soapy water, using either a sponge or soft cloth. No
abrasive cleaners should be used.
o Outer parts of the oven should be cleaned with warm soapy
water, using either a sponge or soft cloth. No abrasive cleaners
should be used.
o We would recommend that an appropriate stainless steel cleaner
and polish is regularly used on the stainless steel surfaces of this
appliance.
13
Page 14
Timer functions
The minute minder function
The minute minder function is a countdown time that can be set on the
oven programmer/timer. When the countdown time has finished, an
audible signal will sound.
o Press and hold down the programme button (6) until the
decimal point starts to flash to enter programming mode.
o Use the plus (7) and minus (5) buttons to set the countdown
time that you require.
o The maximum countdown time that can be set is 23 hours and
59 minutes.
o When the correct countdown time appears on the LED display,
release the plus and minus buttons and the countdown will start
immediately.
o The oven in use symbol (4) will appear on the LED display to
show that a countdown time is in progress.
o After a few seconds the LED display will return to showing the
time of day.
o At the end of the countdown time, an audible signal will sound
and the oven in use symbol will go out. The audible signal will
sound for 7 minutes before switching off or you can silence it by
pressing any of the oven programmer/timer buttons.
o IMPORTANT: If the oven is in use whilst using the minute
minder function, the oven WILL NOT switch off at the end of the
countdown time. YOU MUST turn the oven function selector
knob and the thermostat control knob to their OFF positions.
14
Page 15
The semi-automatic cooking function
This function will allow you to set a countdown time similar to the
minute minder function, however the oven will switch off at the end of
the cooking time.
o Place the food that you want to cook inside of the oven and
close the door.
o Select an oven function and cooking temperature using the
relevant control knobs.
o Press and hold down the programme button (6) until the
decimal point starts to flash to enter programming mode, the
oven in use symbol (4) will appear on the LED display.
o Release the programme button and then press it again. The
automatic cooking symbol (1) will flash and “dur” will appear
briefly on the LED display before showing “0.00”.
o Use the plus (7) and minus (5) buttons to set the cooking time
that you require.
o The maximum countdown time that can be set is 10 hours.
o When the correct countdown time appears on the LED display,
release the plus and minus buttons. Cooking will begin
immediately, after a few seconds the countdown time will start.
o The automatic cooking symbol and the oven in use symbol (2)
will appear on the LED display.
o At the end of the cooking time, an audible signal will sound and
the automatic cooking symbol will flash on the LED display.
o To reset the oven and cancel the audible alarm, press the
programme button until the oven in use symbol appears on the
LED display and the automatic cooking symbol goes out.
o IMPORTANT: If you have not turned the oven function selector
knob and thermostat control knob to their OFF positions, when
you reset the oven it will continue to heat.
15
Page 16
The end of cooking function
This function is similar to the semi-automatic function, however
instead of setting a countdown time, you select the time of day that
you want the oven to switch off at.
o Place the food that you want to cook inside of the oven and
close the door.
o Select an oven function and cooking temperature using the
relevant control knobs.
o Press and hold down the programme button (6) until the
decimal point starts to flash to enter programming mode, the
minute minder symbol (4) will appear on the LED display.
o Release the programme button and then press it again. The
automatic cooking symbol (1) will flash and “dur” will appear on
the LED display.
o Release the programme button and then press it for a third
time, “end” will appear briefly on the LED display before
showing “0.00”.
o Use the plus (7) and minus (5) buttons to set the time of day
that you want the oven to switch off at.
o The maximum countdown time that can be set is 10 hours.
o When the correct time of day appears on the LED display,
release the plus and minus buttons. Cooking will begin
immediately, after a few seconds the countdown time will start.
o The automatic cooking symbol and the oven in use symbol (2)
will appear on the LED display.
o At the end of the cooking time, an audible signal will sound and
the automatic cooking symbol will flash on the LED display.
o To reset the oven and cancel the audible alarm, press the
programme button until the oven in use symbol appears on the
LED display and the automatic cooking symbol goes out.
o IMPORTANT: If you have not turned the oven function selector
knob and thermostat control knob to their OFF positions, when
you reset the oven it will continue to heat.
16
Page 17
The automatic cooking function
This function will allow you to set the time of day that you want the
oven to switch off at and how long you want the oven to cook for.
o Place the food that you want to cook inside of the oven and
close the door.
o Select an oven function and cooking temperature using the
relevant control knobs.
o Press and hold down the programme button (6) until the
decimal point starts to flash to enter programming mode, the
minute minder symbol (4) will appear on the LED display.
o Release the programme button and then press it again. The
automatic cooking symbol (1) will flash and “dur” will appear
briefly on the LED display before showing “0.00”.
o Use the plus (7) and minus (5) buttons to set the cooking time
that you require.
o The maximum countdown time that can be set is 10 hours.
o When the correct countdown time appears on the LED display,
release the plus and minus buttons.
o IMMEDIATELY press the programme button, “end” will appear
briefly on the LED display before showing “0.00”.
o Use the plus (7) and minus (5) buttons to set the time of day
that you want the oven to switch off at.
o The automatic cooking symbol and the time of day will appear
on the LED display.
o The appliance will automatically calculate what time of day it
needs to switch the oven on at, so that it runs for the cooking
time that you set.
o When the oven switches on, the oven in use symbol (2) will
appear on the LED display, as well as the automatic cooking
symbol.
o At the end of the cooking time, an audible signal will sound and
the automatic cooking symbol will flash on the LED display.
17
Page 18
o To reset the oven and cancel the audible alarm, press the
programme button until the oven in use symbol appears on the
LED display and the automatic cooking symbol goes out.
o IMPORTANT: If you have not turned the oven function selector
knob and thermostat control knob to their OFF positions, when
you reset the oven it will continue to heat.
Cancelling the semi-automatic and automatic function
o Press and hold down the minus (5) and plus (7) button
simultaneously, until the automatic cooking symbol (1) goes out
and the oven in use symbol (2) is lit.
o IMPORTANT: If you do not turn the oven function selector
knob and thermostat control knob to their OFF positions, when
you reset the timer function, it will continue to heat.
Cancelling the minute minder function
o Press and hold down the programme button (6) until the
decimal point starts to flash to enter programming mode.
o Press and hold down the minus (5) and plus (7) buttons
simultaneously.
o The minute minder symbol (4) will go out.
o IMPORTANT: If you do not turn the oven function selector
knob and thermostat control knob to their OFF positions, when
you reset the timer function, it will continue to heat.
Adjusting the volume of the audible signal
The volume of the audible signal has 3 levels, low, medium and high.
To adjust the volume, you should proceed as follows:-
o IMPORTANT: The oven timer/programmer must not be in any
form of countdown mode and the oven in use symbol (2) must
be lit.
o Press and hold down the minus (5) and plus (7) buttons
simultaneously until the decimal point starts to flash.
o Press the programme button (6)
and the LED display will show
“n” followed by a number. 1 is the loudest volume, 2 is the
middle volume and 3 is the quietest volume.
o Use the minus button to select the volume level that you desire.
18
Page 19
Changing the time of day
o IMPORTANT: The oven timer/programmer must not be in any
form of countdown mode and the oven in use symbol (2) must
be lit.
o Press and hold down the minus (5) and plus (7) buttons
simultaneously until the decimal point starts to flash.
o Release these buttons and then use the minus and plus buttons
to alter the time of day.
Using your oven
Selecting an oven function
The oven function selector knob should be used to select the particular
mode of cooking that you require. The appliance will utilise different
elements within the oven cavity, depending on the oven function that
you select. When a function is selected, the power indicator light will
come on and the oven light.
Oven functions
OVEN LIGHT (BO616SS): Separate light control which
allows the light to be switched on, even when the oven is not
in use.
CONVENTIONAL OVEN (BO628SS, BO636SS/R/W): This
method of cooking provides traditional cooking, with heat from
the top and lower elements. This function is suitable for
roasting and baking on one shelf only.
FAN OVEN (BO616SS, BO636SS/R/W): This method of
cooking uses the circular element while the heat is distributed
by the fan. This results in a faster and more economical
cooking process. The fan oven allows food to be cooked simultaneously
on different shelves, preventing the transmission of smells and tastes
from one dish onto another.
GRILL MODE (BO616SS, BO636SS/R/W): This method of
cooking utilises the inner sections of the top element, which
directs heat downwards onto the food. This function is suitable
for grilling portions of bacon, toast and meat etc.
FULL GRILL (BO636SS/R/W): This method of cooking
utilises the inner and outer parts of the top element, which
directs heat downwards onto the food. This function is
19
Page 20
suitable for grilling medium or large portions of sausages, bacon,
steaks, fish etc.
DEFROST MODE (BO616SS, BO636SS/R/W): The fan runs
without heat to reduce the defrosting time of frozen foods. The
time required to defrost the food will depend on the
room temperature, the quantity and type of food. Always
check food packaging for the defrosting instructions.
LOWER ELEMENT ONLY (BO628SS): This method of
cooking uses the lower element to direct heat upward to the
food. This function is suitable for slow-cooking recipes or for
warming up meals.
CONVECTION OVEN AND FAN (BO628SS): This method of
cooking provides traditional cooking with heat from the top
and the lower element, it also utilises the circulation fan. This
ensures a fast and even distribution of the heat. Suitable for
light and delicate baking, such as pastries.
FAN AND FULL GRILL (BO636SS/R/W): This method of
cooking utilises the top element in conjunction with the fan,
which helps to provide a quick circulation of heat. This
function is suitable where quick browning is required and
“sealing” the juices in, such as steaks, hamburgers, some
vegetables etc.
FAN AND HALF GRILL BO628SS): This method of cooking
utilises the top element in conjunction with the fan, which
helps to provide a quick circulation of a gentle heat. This
function is suitable where browning is required and “sealing”
the juices in, such as steaks, hamburgers, some vegetables
etc.
FAN AND LOWER ELEMENT (BO628SS, BO636SS/R/W):
This method of cooking utilises the bottom element in
conjunction with the fan, which helps to circulate the heat.
This function is suitable for sterilizing and preserving jars.
Thermostat control knob
The oven thermostat control knob sets the
required temperature of the oven. It is
possible to regulate the temperature within
a range of 50 - 250°C.
20
Page 21
Oven operating light
This light will come on to indicate that the
oven’s heating elements are in operation.
The light will turn off when the temperature
set on the thermostat control knob has
been reached. It will cycle on and off
throughout the cooking time.
You should not place food inside the
cavity, until the correct cooking
temperature has been reached.
Cooking guidelines
o Please refer to the information given on food packaging for
guidance on cooking temperatures and times. Once familiar with
the performance of your appliance, temperatures and times can
be varied to suit personal preference.
o When using the fan oven function you should follow the
information given on the food packaging for this particular mode
of cooking.
o You should pre-heat the oven and not place food inside of it until
the oven operating light has gone off. You can choose not to preheat when using the fan oven mode; however you should extend
the cooking time given on the food packaging by at least ten
minutes.
o IMPORTANT: You should ALWAYS pre-heat the oven if you are
baking.
o If there is no guidance given on the food packaging specifically
for cooking in fan oven mode, you can generally reduce the
cooking time and temperature by 10% from the information
given for conventional oven cooking.
o Make sure that frozen foods are thoroughly thawed before
cooking, unless the instructions on the food packaging advise
that you can “cook from frozen”.
o Before cooking, check that any accessories that are not required
are removed from the oven.
o Place cooking trays in the centre of the oven and leave gaps
between the trays to allow air to circulate.
o Try to open the door as little as possible to view the dishes.
21
Page 22
o The oven light will remain on during cooking.
Warnings
o Keep the oven door closed when using any of the cooking
functions, including all grill functions.
o Do not use aluminium foil to cover the enamelled baking tray or
heat items wrapped in aluminium foil under the grill. The high
reflectivity of the foil could potentially damage the grill element.
o You should also never line the base of your oven with aluminium
foil.
o During cooking, never place pans or cookware directly onto the
bottom of your oven. They should always be placed on the
shelves provided.
o The grill heating element and other internal components of the
oven become extremely hot during operation, avoid touching
them inadvertently when handling the food which you are
grilling.
o Important: Be careful when opening the door, to avoid contact
with hot parts of the oven and steam.
o Warning: Accessible parts may become hot during use. Young
children should be kept well away from the oven when it is in
use.
o The enamelled baking tray handle should only be used to
reposition the tray and NOT for removing it from the oven
cavity. When removing the enamelled baking tray, you should
ALWAYS use an oven glove.
o The enamelled baking tray handle should not be left in position
when the appliance is switched on.
22
Page 23
Cleaning and maintenance
Cleaning operations must only be carried out
when the oven is cool.
The appliance should be disconnected from your
mains supply before commencing any cleaning
process.
o The oven should be thoroughly cleaned before it is operated for
the first time and after each use. This will avoid residual food
stuffs becoming baked on the oven cavity. After residues have
been baked on several times, they are far more difficult to
remove.
o Never clean the oven surfaces by steam cleaning.
o The oven cavity should only be cleaned with warm soapy water,
using either a sponge or soft cloth. No abrasive cleaners should
be used.
o Any stains that may appear on the bottom of the oven will have
originated from food splashes or spilt food, these splashes occur
during the cooking process. These could possibly be a result of
the food being cooked at an excessively high temperature or
being placed in cookware that is too small.
o You should make sure that the cooking temperature that is
selected is appropriate for the food that you are cooking. You
should also ensure that the food is placed in an adequately sized
dish and use the enamelled baking tray where appropriate.
o Outer parts of the oven should only be cleaned with warm soapy
water, using either a sponge or soft cloth. No abrasive cleaners
should be used.
o We would recommend that an appropriate stainless steel cleaner
and polish is regularly used on the stainless steel surfaces of this
appliance.
o If you use any form of oven cleaner on your appliance, then you
must check with the manufacturer of the cleaner that it is
suitable for use on your appliance.
o Any damage that is caused to the appliance by a cleaning
product will not be fixed by Baumatic free of charge, even
if the appliance is within the guarantee period.
23
Page 24
Replacing the oven bulb
IMPORTANT: The oven must be disconnected from
your mains supply before you attempt to either
remove or replace the oven bulb.
o Remove all oven shelves and the
enamelled baking tray.
o Remove the light cover by turning it
anti-clockwise.
o Unscrew the bulb clockwise and remove
it from its holder.
o Replace the bulb with a 25 W/300°C, screw type pygmy.
o Do not use any other type of bulb.
o Place the lamp cover back into position.
24
Page 25
Removing the oven door for cleaning
To facilitate the cleaning of the inside of the oven and the outer frame
of the oven, the door can be removed as follows:-
o The hinges (A) have two movable bolts on them (B).
o If you raise both of the movable bolts (B), then the hinges (A)
are released from the oven housing.
o You should grip the sides of the door at the centre and then
incline it slightly towards the oven cavity and then pull it gently
away from the oven cavity.
o IMPORTANT: You should make sure that the door is supported
at all times and that you place the door on some padded
material whilst cleaning it.
o The oven door and door glass should only be cleaned using a
damp cloth and a small amount of detergent. The cloth MUST
NOT have come into contact with any form of cleaning product
or chemical previously.
o To refit the door you should slide the hinges back into their slots
and open the door fully.
o IMPORTANT: The movable bolts (B) must be closed back into
their original positions before closing the door.
o Take care not to dislodge the hinge
locking system when removing the door,
as the hinge mechanism has a strong
spring.
o Do not immerse the door in water at any
time.
25
Page 26
Removing the inner door glass for cleaning
o To facilitate cleaning, the door glass can be lifted out.
o Open the door of the oven to
a 45° angle.
o There is a plastic sealing
section at the top of the oven
door, which has 4 small slots
in it.
o Place a coin horizontally into one of the small slots and rotate
the coin clockwise. You will feel part of the plastic sealing section
disengage from the door.
o Repeat this process for the
other three slots and you will
be able to lift the plastic
sealing section away from
the top of the door.
o This will allow you to access the inner door glass. Carefully lift
the door glass slightly at the top of the oven door and then slide
the door glass towards you, removing it from the oven door.
26
Page 27
o IMPORTANT: Be careful to note which way around the
oven door glass sits inside the oven door. YOU MUST put
the door glass back into the oven door the same way
around.
o IMPORTANT: Care must be taken when cleaning between
the door glasses, and inside the inner frame as some of
the edges maybe sharp due to the manufacturing process.
o Do not use any abrasive cleaner that could cause damage.
o Remember that if the surface of the glass panel becomes
scratched, this could lead to a dangerous failure.
o When refitting, slide the inner door glass back into the oven
door. IMPORTANT: Ensure that the glass sits properly in the
recess at the base of the oven door and that it is the same way
around as it was originally.
o Refit the plastic sealing section to the top of the oven door,
pushing it downwards to clip it back into position.
INSTALLATION
The installation must be carried out by a suitably
qualified person, in accordance with the current
version of the following.
o UK Regulations and Safety Standards or their European
Norm Replacements.
o Building Regulations (issued by the Department of the
Environment).
o Building Standards (issued by the Scottish Development
Department).
o IEE Wiring Regulations.
o Electricity At Work Regulations.
Before connecting the appliance, make sure that the supply voltage
marked on the rating plate corresponds with your mains supply
voltage.
WARNING: THIS APPLIANCE MUST BE EARTHED.
o This appliance should be wired into a 13 A double pole switched
fused spur outlet, having 3 mm contact separation and placed in
an easily accessible position adjacent to the appliance. The spur
outlet must still be accessible even when your oven is located in
its housing.
27
Page 28
o To connect the oven power cord, loosen and remove the cover
on the terminal block, in order to gain access to the contacts
inside. Make the connection, securing the cord in place with the
cable clamp provided and then immediately close the terminal
block cover again.
o If you have to change the oven power cord, the earthing
(yellow/green) conductor must always be 10 mm longer than the
line conductors.
o Care must be taken to ensure that the temperature of the mains
supply cable does not exceed 50°C.
o If the mains supply cable is damaged, then it must be replaced
by an appropriate replacement which can be obtained from the
Baumatic Spares Department.
28
Page 29
Positioning the appliance
o Ensure that the aperture that you will be fitting the oven into is
of the size given in the above diagram.
o The oven must be fitted into an oven housing with the ventilation
cut-outs shown in the “Ventilation requirements” section on the
next page.
o Ensure that the rear panel of the furniture housing unit has been
removed.
29
Page 30
Ventilation requirements
(Figure shows the ventilation and cut-out requirements for the
installation of the appliance into a standard kitchen unit).
(Figure shows the
ventilation and cutout requirements for
the installation of the
appliance into a tall
housing unit).
30
Page 31
Installing the oven into the housing unit
o IMPORTANT: Before installing the appliance into the housing
unit, YOU MUST attach the “drip catcher” to the lower front edge
of the oven using the 3 screws supplied. The above line drawing
shows how you attach the “drip catcher”.
o Ensure that the oven has been securely fixed into the housing
unit. The fixing of the oven into the housing is made by using
four screws and caps, which are supplied with the oven.
o Open the door of the oven and then screw through the four holes
on the edge of the oven cabinet into the housing unit.
31
Page 32
My appliance isn’t working correctly
o The oven isn’t coming on.
* Check that you have selected a cooking function and a cooking
temperature.
* Check that the automatic cooking symbol (1) isn’t lit on the LED
display.
o There appears to be no power to the oven and grill.
* Check that the appliance has been connected to the electrical
mains supply correctly.
* Check that the mains fuses are in working order.
o The grill function works but the main oven does not.
* Check that you have selected the correct cooking function.
o The grill and top oven element is not working, or cuts out
for long periods of time during use.
* Allow the oven to cool for approximately 2 hours. Once cool,
check whether the appliance is again working properly.
o My food is not cooking properly.
* Ensure that you are selecting the correct temperature and the
correct cooking function for the food that you are cooking. It
may be appropriate to adjust your cooking temperature by plus
or minus 10°C, to achieve the best cooking results.
o My food is not cooking evenly.
* Check that the oven has been installed correctly and is level.
* Check that the correct temperatures and shelf positions are
being used.
o The oven light is not working.
* Refer to page 23 and follow the “Replacing the oven bulb”
section.
32
Page 33
o I am getting condensation in my oven.
* Steam and condensation is a natural by product of cooking any
food with high water content, such as frozen food, chicken etc.
* You may get condensation in the oven cavity and forming
between the oven door glasses. This is not necessarily a sign
that the oven is not working correctly.
* Do not leave food in the oven to cool after it has been cooked
and the oven has been switched off.
* Use a covered container, where practical, when cooking to
reduce the amount of condensation that forms.
IMPORTANT: If your appliance appears not to be
operating correctly, then you should disconnect it
from your mains supply and then contact
Baumatic Customer Care on telephone number
(0118) 933 6911.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE
YOURSELF.
Please note that if an engineer is asked to attend whilst the product is
under guarantee and finds that the problem is not the result of an
appliance fault, then you may be liable for the cost of the call out
charge.
The appliance must be accessible for the engineer to perform
any necessary repair. If your appliance is installed in such a
way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then he will not complete a
repair.
This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance, like plinths. Or any installation other
than the one specified by Baumatic Ltd. has been completed.
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance.
IMPORTANT: Baumatic Ltd. operates a policy of continuous
improvement and reserves the right to adjust and modify its
products without prior notification.
33
Page 34
Baumatic Consumables
o BC001 Degreaser for Dishwashers (200 g)
o BC002 Descaler for Washing Machines and Dishwashers (200 g)
o BC003 Ceramic Hob Cleaner (250 ml)
o BC004 Oven Cleaner (250 ml)
o BC005 Stainless Steel Cleaner and Protector (250 ml)
o BC007 E-Cloth – General Purpose Cloth
o BC008 Microwave Cover
To order a Baumatic consumable product please call 0123 5437 244
and quote the product code. You can also order online from
eshop.baumatic.co.uk
34
Page 35
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Customer Care Telephone
(0118) 933 6911
Customer Care Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Advice Line Telephone
(0118) 933 6933
E-mail:
sales@baumatic.co.uk
customercare@baumatic.co.uk
spares@baumatic.co.uk
technical@baumatic.co.uk
Website:
www.baumatic.co.uk
Facebook:
www.facebook.com/baumatic.uk
Republic of Ireland
Service Telephone
1-890 812 724
Spares Telephone
091 756 771
Czech Republic
Baumatic CR s.r.o.
Lípová 665
460 01 Liberec 4
Czech Republic
+420 483 577 200
www.baumatic.cz
Slovakia
Baumatic Slovakia, s.r.o.
Galvániho 7/D
Slovakia
+421 255 640 618
Germany
Baumatic Gmbh
Bachstr.10-12
D-32 257 Bünde
Deutschland
+49 (0) 5223 99408 0
www.baumatic.de
Italy
Baumatic Italia S.R.L.
Via Galvani N.3
35011 Campodarsego (PD)
+3904 9920 2297
www.baumatic.it
Holland
Baumatic Benelux B.V.
Dukdalfweg 15d
1332 BH ALMERE
Nederland
+31(0)36 549 1553
www.baumatic.nl
35
Page 36
36
Loading...