Baumatic BE2SS User Manual

BE2SS 30 cm 2 Solid plate
electric domino hob

1

ELECTRIC

HOBS

USER AND INSTALLATION

INSTRUCTIONS

For future reference please record the following information which can be
found on the Rating Plate and the date of purchase which can be found in the
invoice:

Model Number .

Serial Number .

Date of Purchase .

TECHNICAL DATA

ELECTRICAL DETAILS

Rated Voltage: 230V ac 50Hz

Supply Connection: Switched Double-pole Isolator with 3mm contact separation

POWER INPUTS AND PROTECTION RATING

Model Max Total Min Fuse

kW Amps Protection Rating

B65 6.0 26.1 30A

BE2SS 3.5 15.2 16A

BVC2SS 2.9 12.6 16A

Mains Supply Connection Cable: 3 x 2.5mm2 Type H05 RR-F <HAR> marked

NOTE:

For cable connection details, see diagram on appliance base plate.

2

CONTENTS

General Information page 4

Warning and Safety Instructions page 5

Instructions for Use pages 6 —

7

Instructions for Installation Pages 8 — 1

0

Technical Data Page 11

Conditions of Guarantee Back cover

3

GENERAL INFORMATION

Please read this booklet thoroughly before you use this appliance. It is important that you
understand all the control functions before commencing to cook with your Baumatic appliance.

Please remember the advice and warnings shown on page 5 which is headed

IMPORTANT — Warning and Safety Instructions .

This appliance is designed for domestic household use when built into kitchen worktop.
NOTE: The housing, adjacent furniture and all materials used in the installation must be able to
withstand a minimum temperature rise of 85°C above ambient during periods of operation. This
information is for guidance only and the actual withstand temperature will depend on the
performance rating for the surface finish of the worktop.
Certain types of kitchen furniture surface finishes are particularly prone to heat damage or
discolouration at temperatures lower than the above guidelines.
Installing the appliance in contravention of the guidance given will be at the liability of the
owner.

The use for any other purpose or in any other environment without the express agreement of
Baumatic Ltd, would invalidate any warrantee or liability claim.

Your new appliance is guaranteed against electrical or mechanical defects subject to certain
exclusions noted in Baumatic Ltd Conditions of Guarantee.
The aforegoing does not affect your statutory rights.

The Warrantee applies to Great Britain and Northern Ireland only.
In the event that you require any After Sales Service or advice, please contact the Baumatic
Service Department on telephone number — 0118 933 6911.

Before using this appliance ensure that any protective packaging or coatings have been removed.
To aid the protection of the environment, please sort the packing materials into different types
and dispose of them in accordance with the local waste disposal laws.
Any further information on waste disposal can be obtained from your local Environment Agency office.
When first used, an odour may be emitted by any residual protective finish or moisture, which
will cease after a short period of time.

This appliance has been constructed and distributed in compliance with the essential requirements
of the following EEC DIRECTIVES and EUROPEAN NORMS:

CE Marking — 93/68 Low Voltage — 73/23 EMC — 89/336
Materials that can touch food — 89/109.
Safety Standards — EN 60 335-1, EN 60 335 — 2 — 6.

As Baumatic have a policy of continued product improvement, the right is reserved to adjust and
make any modifications deemed necessary without notification.

INSTALLATION INSTRUCTIONS

9

INSTALLATION NOTES

1 Cut the aperture to the dimensions shown in the table below or use the template provided on

the packaging.

2 Invert the hob and apply the sealing agent provided to match the outer perimeter edge.
3 If the sealing agent is a strip type, the protective covering must be removed from both sides.

Do not leave a gap in the sealing agent or overlap the thickness.
NOTE: do not use any Silicone based sealant, as this can damage the worktop surface if

repairs are required.

4 Insert the appliance into the aperture and fix into position via the clamps & screws, tightening

the screws evenly (see Fig.3).

Fig.3

HOB APERTURE DIMENSIONS

MODEL A B C D E

B65

500

585 480

560

30

BE2SS

510

290 480

285

30

BV2SS

510

290 490

270

40

4