Page 1
IMPORTANT!
PLEASE READ THIS MANUAL AND KEEP IT FOR FUTURE REFERENCE!
THIS MANUAL CONTAINS SECTIONS OF SAFETY INSTRUCTIONS, OPERATING INSTRUCTIONS
& TROUBLESHOOTING TIPS, ETC.
BAUMATIC
BDW2W / BDW2SS DISHWASHER
60CM FULL HEIGHT DISHWASHER
INSTRUCTION MANUAL
CAREFULLY READING IT BEFORE USING THE DISHWASHER WILL HELP
YOU USE AND MAINTAIN THE DISHWASHER PROPERLY.
09/01/06
Page 2
BAUMATIC BDW2W / BDW2SS dishwasher user manual
CONTENTS
2
BEFORE CALLING
FOR SERVICE
REVIEWING THE SECTION ON
TROUBLESHOOTING TIPS WILL
HELP YOU SOLVE SOME
COMMON PROBLEMS WITHOUT
THE NEED TO ASK FOR HELP
FROM PROFESSIONAL
TECHNICIANS.
PLEASE NOTE:
THE MANUFACTURER
RESERVES THE RIGHT TO MAKE
MODIFICATIONS TO PRODUCTS
WITHOUT GIVING PRIOR NOTICE.
• SAFETY FIRST!
SAFETY INFORMATION .……………..…….……3
*Please read this before using your dishwasher!
• KNOWING YOUR
DISHWASHER
CONTROL PANEL ………………………..….…..…4
DISHWASHER FEATURES …………..…….…….4
• USING YOUR DISHWASHER
WATER SOFTENER …………………..………...5-6
DETERGENT ………………..............................6
RINSE AID ………………….............................7
LOADING YOUR DISHWASHER…..….......8-11
STARTING A WASH CYCLE ……………….12-13
UNLOADING AT THE END OF A CYCLE…....14
FILTERING SYSTEM ………………..…….…….15
CLEANING AND MAINTAINING
YOUR DISHWASHER …………………….…15-17
• BEFORE YOU CALL FOR
SERVICE…
TROUBLESHOOTING ………………….…18-22
• MISCELLANEOUS
CHARACTERISTICS ………….………….……...23
HOW TO INSTALL ……….…….…..……....24-31
FINAL CHECKLIST BEFORE STARTING…….32
CONDITIONS OF GUARANTEE………………..33
CONTACT DETAILS…………………………..…..34
2
Page 3
BAUMATIC BDW2W / BDW2SS dishwasher user manual
3
IMPORTANT SAFETY INFORMATION
READ BEFORE USING!
ELECTRICAL SAFETY
• NOTE
• Manufacturer declines all respo nsibili ty for any
• DURING THE GUARANTEE PERIOD ONLY BAUMATIC
• DO NOT USE IF THE SUPPLY CORD IS DAMAGED.
• FOR INSTALLATION PROCEDURE PLEASE CONSULT
- This appliance must be grounded. In
the event of a malfunction or breakdown,
grounding will reduce the risk of electric sho ck
by providing a path of least resistance of
electrical current. You will be able to tell if it is
because a non-grounded appliance will give off
an electrical discharge.
damage due to non-grounding of appliance.
SERVICE ENGINEERS OR AN AUTHORISED AGENT
OF BAUMATIC SHOULD CARRY OUT REPAIRS ON
THIS UNIT.
PAGES 24 – 31.
BEFORE USING
IN YOUR DISHWASHER. PLEASE SEE PAGE 8 FOR A LIST
OF THESE ITEMS.
1) Keep sharp items like knives away from the door seal.
2) Load sharp knives with the handles up to prevent
injuries.
DETERGENT, NOT SOAP OR LAUNDRY DETERGENT.
NEVER USE SOLVENTS AS THIS COULD RESULT IN AN
EXPLOSION!
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY BEFORE
SOME ITEMS ARE UNSUITABLE FOR WASHING
DO NOT TAMPER WITH THE CONTROLS.
WHEN LOADING ITEMS TO BE WASHED:
ONLY USE AUTOMATIC DISHWASHER
USING YOUR DISHWASHER FOR THE FIRST TIME!
• DO NOT ABUSE OR FORCE THE DISHWASHER.
• KEEP CHILDREN AWAY FROM DETERGENT,
• SUPERVISE YOUNG CHILDREN TO ENSURE
• SUPERVISE INFIRM PERSONS IF THEY MUST
• REMOVE THE DOOR TO WASHING
CHILD SAFETY
DO NOT SIT ON OR STAND ON ITS DOOR OR
DISH RACKS – TIPPING HAZARD.
RINSE AID AND THE OPEN DOOR OF THE
DISHWASHER AS THERE COULD BE
DETERGENT LEFT INSIDE.
THEY DO NOT PLAY WITH THE APPLIANCE.
USE THE APPLIANCE.
COMPARTMENT OF YOUR OLD APPLIANCE
BEFORE DISCARDING IT.
DURING USE
• DO NOT TOUCH THE HEATING ELEMENT
DURING OR IMMEDIATELY AFTER USE.
• DO NOT USE YOUR DISHWASHER UNLESS
ALL ENCLOSURE PANELS ARE PROPERLY IN
PLACE. OPEN THE DOOR VERY CAREF UL LY
IF THE DISHWASHER IS OPERATING.
THERE IS A RISK OF WATER SQUIRTING
OUT.
AFTER USE
• ALWAYS KEEP THE DOOR CLOSED TO AVOID DANGER
OF TRIPPING.
• CHECK THAT THE DETERGEN T DISPENSER IS EMPTY
AFTER COMPLETION OF WASH CYCLE.
• IF LEAVING UNUSED FOR A LONG TIME, DISCONNECT
THE WATER SUPPLY (SEE PP. 17, 28).
3
Page 4
BAUMATIC BDW2W / BDW2SS dishwasher user manual
CONTROL PANEL
4
1 POWER / ON Light: Comes on when the ON / OFF Button is pressed down.
2 Rinse Aid Warning Light: Comes on when rinse aid needs to be refilled.
3 Salt Warning Light: Comes on when the softener needs to be refilled.
4 ON / OFF Button: Turns on/off the power supply.
5 Rapid Button: Only used with cycle ‘
6 Plus Button: Only used with cycle ‘
7 Door Handle: Pull it to open the door.
8 Washing Program Selector: Turn the knob clockwise to select the wash cycles.
’.
’.
DISHWASHER FEATURES
1 ADJUSTABLE UPPER BASKET
2 SPRAY ARMS
3 LOWER BASKET
4 WATER SOFTENER
5 MAIN FILTER
6 DETERGENT DISPENSER
7 CUP & GLASS SHELF
(ADJUSTABLE)
8 CUTLERY BASKET
4
9 COARSE FILTER
10 RINSE AID DISPENSER
11 DRAIN PIPE CONNECTOR
12 INLET PIPE CONNECTOR
Page 5
BAUMATIC BDW2W / BDW2SS dishwasher user manual
5
Note on chemicals used by the dishwasher
• Your dishwasher is equipped with an adjustable rinse aid and salt container. Using individual detergents,
rinse aid and salt will give the best possible results as this will give the correct dosage of each chemical to
suit your needs. Using Two-in-One or Three-in-One tablets may not give the best results when used in
your appliance, and may not be suitable for the type of water supply in your home, as they contain
pre-determined quantities of salt, rinse aid and detergent and cannot be adjusted to the individual
requirements.
If you are going to use 3-in-1 (or 2-in-1) tablets, we suggest that you contact the manufacturer before use or
if you experience poor results in the wash performance and ask for assistance from them.
WATER
SOFTENING
FEATURE
THE LIME IN HARD WATER MAKES DEPOSITS FORM ON
DISHES AND UTENSILS. YOUR DISHWASHER HAS A
SPECIAL SOFTENING FEATURE THAT USES SALT
SPECIFICALLY DESIGNED TO ELIMINATE LIME AND
MINERALS FROM THE WATER
.
WARNING!
ONLY USE DISHWASHER SALT IN YOUR
DISHWASHER.
NOTE:
IF YOU USE 3-IN-1 OR 2-IN-1 TABLETS, BE
SURE NOT TO ADD SALT AND/OR RINSE AID
TO THE APPLIANCE AS THESE TABLET
TYPES ALREADY CONTAIN SALT AND/OR
RINSE AID. ADDING SALT AND RINSE AID
TO YOUR DISHWASHER’S COMPARTMENTS
IN A CYCLE INVOLVING A 3-IN-1 OR 2-IN-1
TABLET WILL RESULT IN OVERDOSING OF
INDIVIDUAL CHEMICALS AND MAY CAUSE
OVERFLOWING OF WATER AND SUDS.
LOADING SALT INTO THE SALT CONTAINER
• REMOVE THE LOWER BASKET & THEN
UNSCREW AND REMOVE THE CAP FROM
THE SALT CONTAINER.
• IF YOU ARE FILLING THE CONTAINER
FOR THE FIRST TIME, FILL WITH
APPROX. 1 LITRE OF WATER.
• PLACE THE END OF THE SUPPLIED
FUNNEL INTO THE HOLE & ADD 1.2 Kg
OF SALT. NOTE
SMALL AMOUNT OF WATER TO COME
OUT OF THE CONTAINER.
: IT IS NORMAL FOR A
5
Page 6
BAUMATIC BDW2W / BDW2SS dishwasher user manual
SETTING THE WATER SOFTENER LEVEL
YOU CAN ADJUST THE AMOUNT OF SALT USED BY THE DISHWASHER TO SOFTEN WATER TO GET THE
ADJUSTMENTS SHOULD BE MADE ACCORDING TO THE TABLE BELOW:
Clarke Degrees
BEST WASHING RESULTS, BASED ON THE HARDNESS OF WATER IN YOUR AREA.
1 UNSCREW THE CAP FROM THE SALT
CONTAINER.
2 THERE IS A RING ON THE NECK OF THE
CONTAINER. ROTATE THE RING IN AN
ANTICLOCKWISE DIRECTION FROM THE “-”
SETTING TOWARDS THE “+” SETTING
ACCORDING TO THE HARDNESS OF W A TER IN
USE. SEE TABLE BELOW.
1. THE SALT CONTAINER MUST BE REFILLED WHEN THE
SALT WARNING LIGHT COMES ON. ALTHOUGH THE
SALT CONTAINER MAY BE FULL, THE INDICATOR LIGHT
MAY NOT GO OUT UNTIL THE SALT HAS DISSOLVED.
2. IF THERE ARE SALT SPILLS, A SOAK PROGRAM CAN
BE RUN TO WASH AWAY SPILLAGE BEFORE USING THE
MACHINE.
3. CLEAR ANY SALT GRANULES AWAY FROM THE
CONTAINER OPENING.
WATER H ARDNESS
Salt con sum ption
(gra m/cycle)
dH
mmol /l
Select o r Po siti o n
NOTE
6
Au to nomy
(cycles/1.2kgs)
0~14 0~18 0~ 1. 8
14~36 18~44 1.8~4.4
/
-
0
20 60
/
36~71 44~89 4. 4~ 8.9 ME D 40 30
71 89 8. 9
+
60 20
Contact your local water board for information on the hardness of your water supply.
DETERGENT “How much do I use?”
To OPEN the DETERGENT DISPENSER DOOR, use the CATCH on its LOWER SIDE.
*NOTE: SEE P.13 – WASH CYCLE TABLE for AMOUNT of DETERGENT to use.
NOTE:
THE HARDER YOUR WATER, THE MORE DETERGENT
YOU MAY NEED. ADJUST THE DOSE JUST BY SMALL
AMOUNTS UNTIL YOU FIND THE CORRECT AMOUNT OF
DETERGENT TO USE.
• ALWA YS CHECK THE WASH CYCLE T ABLE FOR
DOSAGE ADVICE. NEVER OVERFILL THE
DISPENSER.
• DO NOT OVERDOSE TO PREVENT THE
FORMATION OF DEPOSITS (THE WATER
SOFTENING FEATURE ALREADY TAKES CARE
OF THIS!).
6
Page 7
BAUMATIC BDW2W / BDW2SS dishwasher user manual
FINAL RINSE TO PREVENT WATER FROM
FORMING DROPLETS ON YOUR DISHES THAT
RINSE AID
• TO OPEN THE DISPENSER, TURN THE CAP TO
THE ‘OPEN’ (LEFT) ARROW AND LIFT IT OUT.
• POUR THE RINSE AID INTO THE DISPENSER.
BE CAREFUL NOT TO OVERFILL.
• REPLACE CAP BY INSERTING IT ALIGNED WITH
‘OPEN’ ARROW & TURN IT TO THE CLOSED
(RIGHT) ARROW.
• THE RINSE AID IS RELEASED DURING THE
NEED RINSE AID FOR IT MAY CAUSE A WHITE FILM TO
CAN CAUSE SPOTS AND STREAKS. IT ALSO
IMPROVES DRYING BY ALLOWING WA TER T O
• YOUR DISHWASHER IS DESIGNED TO USE
NOTE
LIQUID RINSE AIDS. THE RINSE AID
DISPENSER CAN BE FOUND INSIDE THE
DOOR NEXT TO THE DETERGENT DISPENSER.
TO FILL THE DISPENSER, OPEN THE CAP AND
POUR THE RINSE AID INTO THE DISPENSER
UNTIL THE LEVEL INDICATOR TURNS
COMPLETELY BLACK. THE DISPENSER
HOLDS ABOUT 100ML OF LIQUID RINSE AID.
• BE CAREFUL NOT TO OVERFILL THE
DISPENSER – THIS COULD CAUSE FROTHING.
WIPE AWAY SPILLS WITH A DAMP CLOTH.
DON’T FORGET TO REPLACE THE CAP
BEFORE YOU CLOSE THE DISHWASHER
: IF YOU HAVE SOFT WATER, YOU MAY NOT
7
FALL OFF THE DISHES.
DOOR.
DEVELOP ON YOUR DISHES.
ADJUSTING THE RINSE AID DISPENSER
As with detergent, the amount of rinse
aid needed for your dishes depends on
the hardness of the water in your area.
Too much rinse aid can result in foaming
and cause cloudiness or streaks on your
dishes. If your water is very soft, you
may not need rinse aid. You can always
dilute the rinse aid with an equal
amount of water.
The rinse aid dispenser has six settings. ALWAYS START WITH THE DISPENSER SET ON “1”. IF SPOTS & POOR
DRYING ARE A PROBLEM, INCREASE THE AMOUNT OF RINSE AID DISPENSED BY REMOVING THE DISPENSER LID
AND ROTATING THE DIAL TO “2”. IF THE DISHES ARE STILL NOT DRYING PROPERLY OR ARE SPOTTED, ADJUST
THE DIAL TO THE NEXT HIGHER NUMBER UNTIL YOUR DISHES ARE SPOT-FREE.
***
NOTE: Please read the notes for detergent use on p. 13.
WHEN TO REFILL THE RINSE
AID DISPENSER - If the rinse
aid warning light (
can judge the rinse aid level by looking at the
black dot on the rinse aid dispenser . As the rinse
aid level decreases, the black dot shrinks. Never
let the rinse aid get below ¼ full.
SEE control panel) is not on, you
As the rinse aid diminishes, the size of the black dot on the r inse
aid level indicator changes, as illustrated below.
Full
3 / 4 fu ll
1 / 2 fu ll
1 / 4 fu ll - Should re fill to eliminate spotting
Empty
7
Page 8
BAUMATIC BDW2W / BDW2SS dishwasher user manual
8
LOADING
YOUR
DISHWASHER
BEFORE LOADING!
• REMOVE ALL SCRAPS OF FOOD.
• EMPTY DRINKS & LIQUIDS FROM CUPS.
• SOFTEN BURNT-ON FOOD IN PANS BY SOAKING.
NOTE:
FOR BEST PERFORMANCE, FOLLOW THESE
LOADING GUIDELINES. FEATURES AND
APPEARANCE OF RACKS & CUTLERY
BASKETS MAY VARY FROM YOUR MODEL.
DO NOT PUT THESE ITEMS IN YOUR DISHWASHER:
•
BRONZE
CUTLERY
• SAUCEPANS
WITH
WOODEN
HANDLES
• CUTLERY WITH
WOODEN,
HORN, CHINA
OR MOTHER
OF PEARL
HANDLES
• PLASTIC
ITEMS THAT
ARE NOT HEAT
RESISTANT
• OLDER
CUTLERY WITH
GLUED PARTS
• BONDED
CUTLERY
ITEMS OR
DISHES
• PEWTER OR
COPPER ITEMS
• LEAD CRYSTAL
GLASS
• STEEL ITEMS
SUBJECT TO
RUSTING
• WOODEN
PLATTERS
• ITEMS MADE
FROM
SYNTHETIC
FIBRES (eg.
SPONGES)
• DELICATE,
REPAIRED OR
PAINT /
PATTERN
OVERLAID
CHINA
8
Page 9
BAUMATIC BDW2W / BDW2SS dishwasher user manual
1
2
9
Note:
Do not wash stainless steel and silver cutlery together. Iron objects can rust
and stain other items. Aluminium tends to go black. Copper, pewter & brass
stain.
HOW TO USE THE UPPER RACK
THE UPPER RACK IS FOR MORE DELICATE
AND LIGHTER DISHWARE SUCH A S GLASSE S,
COFFEE & TEA CUPS, SAUCERS, PLATES,
BOWLS, AND SHALLOW PANS (PROVIDED
THESE ARE NOT TOO DIRTY).
NOTE:
YOUR DISHWASHER COMES WITH AN
ADJUSTABLE TOP RACK (BASKET) –
PICTURED AT RIGHT. ITS HEIGHT CAN
BE ADJUSTED BY UNDOING THE FRONT
RAIL CLIPS, REMOVING THE RACK
COMPLETELY AND LATCHING THE
WHEELS OF THE LOWER LEVEL
(POSITION ‘1’ IN THE FIGURE ON THE RIGH T) OR
THE HIGHER LEVEL
FIGURE ON THE RIGHT) IN THE GROOVE OF
THE RAIL.
(POSITION ‘2’ IN THE
POSITION THE DISHES AND
COOKWARE SO THAT THEY DO NOT
GET MOVED BY THE SPRAY OF WATER.
ALWAYS PLACE GLASSES, CUPS &
BOWLS UPSIDE DOWN.
LOADING GUIDE (UPPER RACK):
9
Page 10
BAUMATIC BDW2W / BDW2SS dishwasher user manual
***NOTE***: THE UPPER RACK HAS
SIDE FLAPS (PICTURED AT LEF T ABOVE BASKET).
THERE ARE 4 (2 ON EACH SIDE).
THESE CAN BE ADJUSTED INTO 2
POSITIONS = POSITION 1 (HIGH) AND
POSITION 2 (LOW).
10
TO MOVE THE FLAPS BETWEEN THESE
POSITIONS, FIND THE LARGE HINGES
CLASPING EACH FLAP TO THE UPPER
RACK. THERE ARE TWO OF THESE AT
EITHER END OF EACH FLAP. GENTLY PULL
BOTH CLASPS OFF THE WIRE RACK AND
MOVE THE FLAP TO THE DESIRED POSI TION.
BE CAREFUL IF YOU HAVE LONG
FINGERNAILS!
POSITION 1
THE UPPER POSITION WILL ACCOMMODATE ITEMS SUCH AS GLASS TUMBLERS
(PLACED BENEATH FLAP) AND WINE GLASSES. WINE GLASSES CAN BE PLACED
UPSIDE DOWN SO THAT THE NECK NESTLES SNUGLY IN THE GROOVES AT SIDE OF
FLAP WITH THE BASE OF THE GLASS FACING UPWARD.
POSITION 2
WHEN THE FLAPS ARE MOVED T O THE LOWER POSITION, THEY CAN B E USED TO HOLD
ADDITIONAL TUMBLERS, CUPS AND MUGS. ALWAYS CHECK THAT YOU ARE ONLY
PLACING ITEMS ON THE FLAPS THAT WILL CLEAR THE CEILING HEIGHT OF YOUR
DISHWASHER WHEN YOU PUSH THE RACK BACK IN. BE PARTICULARLY CAREFUL
WITH LONG-STEMMED GLASSWARE SUCH AS CHAMPAGNE GLASSES – BREAKAGE
HAZARD!
HOW TO LOAD THE LOWER RACK:
PLACE LARGE ITEMS THAT ARE HARD TO CLEAN IN THE LOWER RACK: eg. POTS, PANS,
LIDS, SERVING DISHES, BOWLS.
• POTS, SERVING BOWLS, ETC. MUST ALWAYS BE PLACED UPSIDE DOWN.
• DEEP POTS SHOULD BE SLANTED TO LET WATER FLOW OUT.
• THE BOTTOM RACK FEATURES FOLD DOWN BASKETS SO THAT LARGER OR MORE POTS &
PANS CAN BE LOADED.
10
Page 11
BAUMATIC BDW2W / BDW2SS dishwasher user manual
1
2
3
4
5
11
CUTLERY BASKET
CUTLERY SHOULD BE PLACED IN THE CUTLERY BASKET WITH HANDLES ALWAYS POINTING
DOWNWARD (AT THE BOTTOM). VERY LONG UTENSILS (LADLES, etc.) SHOULD BE PLACED
HORIZONTALLY AT THE FRONT OF THE UPPER RACK.
Forks
Soup Spoons
Dessert Spoons
Teaspoons
Knives
6 Serving Spoons
7 Gravy Ladle
8 Serving Fork
NOTE
• WHEN YOU ARE SATISFIED YOU HAVE LOADED ALL THE UTENSILS AND
DISHES YOU WANT TO WASH AND HAVE ADDED THE PROPER AMOUNT OF
DETERGENT TO THE DISPENSER
FOR THE DOSE THAT’S RIGHT FOR THE WASHING CYCLE YOU WANT),
THE RACKS ARE PUSHED ALL THE WAY BACK INTO YOUR DISHWASHER AND
CLOSE THE DOOR.
• YOU ARE NOW READY TO START A WASH CYCLE (SEE NEXT PAGE).
(REMEMBER TO CHECK THE TABLE ON PAGE 13
:
ENSURE
11
Page 12
BAUMATIC BDW2W / BDW2SS dishwasher user manual
STARTING A WASH CYCLE
12
.
Intensive
(strong) 120
mins.
1) MAKE SURE THAT THE PLUG OF THE APPLIANCE IS INSERTED INTO THE WALL SOCKET.
2) MAKE SURE THAT THE WATER SUPPLY IS TURNED ON TO FULL PRESSURE.
3) LOAD THE DISHWASHER (SEE THE SECTION ENTITLED ‘LOADING YOUR DISHWASHER’).
4) POUR IN DETERGENT (SEE THE SECTION ENTITLED ‘SALT, DETERGENT & RINSE AID’).
5) TURN THE KNOB LOCATED ON THE RIGHT OF THE CONTROL PANEL CLOCKWISE UNTIL
THE DIAL POINTS TO THE SYMBOL FOR THE CYCLE SETTING. SEE THE ‘WASH CYCLE
TABLE’ ON THE NEXT PAGE.
6) PRESS THE ON/OFF BUTTON – THE ON/OFF LIGHT WILL TURN ON. AT THIS POINT, THE
WASH CYCLE WILL BEGIN.
Approximate Timing of Wash Cycles
Normal
114
mins.
Economy
mins.
93
Rinse
80
mins.
Glass
53
mins.
Rapid
30
mins.
Soap
7
mins.
12
Page 13
BAUMATIC BDW2W / BDW2SS dishwasher user manual
(
)
(
)
5 grams (pre)
/ 22 grams
main
5 grams (pre)
/ 22 grams
main
22 grams
13
15 grams
15 grams
• PLUS BUTTON
Press this button to give a ‘SUPER’ Wash (on table as ‘INTENSIVE’ Wash) when you have to wash pots and pans
with dry, caked-on food (always soak extreme cases of burnt-on food, etc. first). Turn the knob to ‘NORMAL’ to
begin this cycle. A SUPER CYCLE will start.
You should not use the PLUS BUTTON when washin g delicate items. The high temperature used in this wash
could damage delicate items over time.
• RAPID BUTTON
Press this button to give a ‘QUICK’ Wash (on table as ‘RAPID’ Wash) when you want to wash items quickly.
This cycle uses a lower temperature (50
) and has no drying phase.
OVERFLOW PROTECTION
YOUR BAUMATIC DISHWASHER HAS AN OVERFILL PROTECTION DEVICE WHICH AUTOMATICALLY SHUTS OFF
THE INLET VALVE AND STARTS THE DRAIN PUMP IF THE WATER OVERFLOWS. IF THIS OCCURS THEN TURN
OFF THE MAINS WATER SUPPLY BEFORE CALLING THE SERVICE DEPARTMENT. IF THERE IS WATER IN THE
BASE PAN BECAUSE OF AN OVERFILL OR SMALL LEAK, THE WATER SHOULD BE REMOVED BEFORE
RESTARTING THE DISHWASHER.
13
Page 14
BAUMATIC BDW2W / BDW2SS dishwasher user manual
14
FORGET TO ADD A DISH?
A FORGOTTEN DISH CAN BE ADDED AT ANY TIME BEFORE THE DETERGENT
DISPENSER OPENS.
• OPEN THE DOOR A LITTLE TO STOP THE WASHING.
• WAIT ABOUT TEN SECONDS. AFTER THE SPRAY ARMS STOP WORKING,
YOU CAN OPEN THE DOOR COMPLETELY.
• ADD FORGOTTEN DISHES.
• CLOSE THE DOOR, THE DISHWASHER WILL WORK AFTER TEN SECONDS.
NEED TO INTERRUPT A CYCLE?
If an emergency arises, you can stop the machine at any time by pressing the
ON/OFF button. R emember to wait approx. 10 seconds
as the spray arms continue to turn after the power has been cut and could spray hot
water up at you. DO NOT TURN THE KNOB AHEAD AS THIS WILL AFFECT THE
WASHING RESULT! YOU ALSO COULD JUST PULL THE DOOR OPEN – DO NOT
If you need to change a cycle, you can as long as the dishwasher has only been
running for a short time. Just press the ON/OFF button so the ON light goes out, turn
the knob to the setting you want then turn th e dishwasher back on with the ON/OFF
button.
However, if it’s been a long time since the old cycle began, the detergent may have
already been released and the wash water drained out. Yo u’ll need to start a new cycle
altogether so press the ‘ON/OFF’ button to switch the dishwasher off, wait until the inside
cools before you refill the detergent dispenser, close the door and then turn the knob to
the cycle setting you want before you turn your dishwasher back on.
TOUCH ANY BUTTONS!
NOTE:
before you open the door fully ,
WASHING. THE HOT WATER MAY SCALD YOU!
AT THE END OF THE WASH CYCLE
When the knob stops turning and lines up with the STOP mark (see figure), the
cycle has finished. Turn the dishwasher off using the ON/OFF button and open the door of the
dishwasher. Wait a few minutes before unloading the dishwasher so the dishes can cool down.
This will make them less breakable and allow them to dry better.
TAKE CARE WHEN OPENING THE DOOR DURING
14
Page 15
BAUMATIC BDW2W / BDW2SS dishwasher user manual
S
R
R
15
FILTERING SYSTEM
THE FILTER REMOVES BITS OF FOOD TRAPPED IN THE FILTER FROM THE WASH W ATER SO IT CAN BE RECIRCULATED
FOR YOUR CONVENIENCE, WE HAVE PLACED THE FILTERING SYSTEM WITHIN EASY REACH INSIDE THE TUB.
DURING THE CYCLE. THERE ARE THREE PARTS TO THE FILTERING SYSTEM: 1) The Main Filter, 2) The Coa rse
Filter & 3) The Fine Filter.
1 MAIN FILTER
Food and soil particles trapped by this filter are
pulverized by a special jet on the lower spray arm and
washed down the drain.
2 COARSE FILTER
Larger items, such as pieces of bone or glass that could
clog the drain are trapped in the coarse f ilter . To remov e
an item caught in this filter, gently squeeze the tabs
on top of this filter and lift it out.
3 FINE FILTER
This filter holds soil and food residue in the sump area
and prevents it from being re-deposited on the dishes
during a cycle.
Caring for your Dishwasher
CLEANING THE OUTSIDE SURFACES OF YOUR APPLIANCE
• TO CLEAN THE EXTERIOR OF YOUR DISHWASHER (INCLUDING THE CONTROL PANEL), USE A LIGHTLY
DAMPENED CLOTH THEN DRY THOROUGHLY. NEVER USE SHARP OBJECTS, SCOURING PADS OR
HARSH CLEANERS ON ANY PART OF THE APPLIANCE. SOME PAPER TOWELS CAN SCRATCH.
• TO CLEAN THE EDGE AROUND THE DOOR,
ONLY EVER USE A SOFT WARM, DAMP R AG.
DO NOT USE A SPRAY CLEANER HERE OR
WHEN CLEANING THE DOOR PANEL AS THIS
MAY HARM THE DOOR LOCK AND ELECTRICAL
PARTS.
CLEANING THE SPRAY ARMS
THE SPRAY ARMS NEED REGULAR CLEANING AS HARD WA TER RESIDUES WILL CLOG THEIR JET
& BEARINGS. TO REMOVE THE SPRAY ARM, SCREW OFF THE NUT TO TAKE OUT THE WASHE
ON TOP OF THE SPRA Y ARM AND REMOVE THE ARM. WASH THE ARMS IN SOAPY WARM W A TE
& USE A SOFT BRUSH TO CLEAN THE JETS. REPLACE THE SPRAY ARM AFTER RINSING IT
THOROUGHLY.
15
Page 16
BAUMATIC BDW2W / BDW2SS dishwasher user manual
16
CLEANING THE FILTERS
• THE FILTER ASSEMBLY MUST BE KEPT CLEAN FOR BEST PERFORMANCE. You should remove the
larger bits of food trapped in the filter after each wash cycle by rinsing the semicircular filter and cup
under running water. To remove the filter assembly, pull up on the cup handle.
• The entire filter assembly should be cleaned at least once a month.
• T o clear the coarse filter and the fine filter, use a cleaning brush. Then, reassemble the filter parts as
shown in the figure above and reinsert the entire assembly in the dishwasher in its seat & press
downward to secure it.
• Improper replacement of the filter may impair appliance performance and damage dishes and
utensils.
• Warning - never
run the dishwasher without the filters in
place!
• Warning - Before clea ning the inner cavity of the appliance
always allow 30 minutes for the Element to cool down to avoid
injury!
16
Page 17
BAUMATIC BDW2W / BDW2SS dishwasher user manual
HOW TO KEEP YOUR DISHWASHER IN SHAPE
17
AFTER EVERY WASH, leave the door slightly ajar so that moisture and odours are not trapped
inside.
REMOVE THE PLUG before cleaning or performing maintenance. Never run the risk of electric
shocks.
DO NOT USE SOLVENTS OR ABRASIVE CLEANING AGENTS to clean the exterior and the rubber parts
of the dishwasher . Only use a cloth and w arm soapy water . T o remov e spots or stains from the
surface of the interior, use a cloth dampened with water and a little white vinegar, or a cleaning
product made specifically for dishwashers.
WHEN YOU GO ON HOLIDAY, run a wash cycle with the dishwasher empty. Then unplug it, turn
off the water supply and leave the door slightly ajar to prevent odours and mould from
developing.
MOVING THE APPLIANCE is possible but KEEP IT UPRIGHT.
SEALS can trap food, which in turn will caus e odours. Periodic cleaning with a damp cloth or
sponge will prevent this from becoming a problem.
PROTECTING YOUR DISHWASHER AGAINST FREEZING
If your dishwasher is left in an unheated place d uring the winter, ask a service
technician to:
Cut off electrical power to the dishwasher. Remove fuses or trip circuit
1)
breaker.
2) Turn off the water supply and disconnect the water inlet pipe from the water
valve & discharge hoses.
3) Drain water from the inlet pipe and water valve (Use a pan to catch the water).
4) Reconnect the water inlet pipe to the water valve.
5) Remove the plastic sump cover in the tub bottom and use a sponge to soak up
water in the rubber boot.
17
Page 18
BAUMATIC BDW2W / BDW2SS dishwasher user manual
BEFORE YOU CALL FOR SERVICE …
CHECKING AGAINST THE CHARTS BELOW MAY FIX YOUR PROBLEM.
PROBLEM POSSIBLE CAUSES WHAT TO DO
• Replace fuse or res et circ uit bre ake r.
• Fuse blown, or the
circuit breaker acted
• Remove any other appliances
feeding from the same socket as the
dishwasher.
18
Dishwasher
doesn’t run!
Drain Pump
doesn’t stop!
• Power supply is not
turned on
• Water pressure is low
• Overflow
• Make sure the dishwasher is turned
on and the door is closed securely.
• Check that the water supply is
connected properly and the water is
turned on.
• The system is designed to detect an
overflow. When it does, it shuts off
the circulation pump and turns on
the drain pump. Call a Baumatic
Ltd approved technician.
18
Page 19
BAUMATIC BDW2W / BDW2SS dishwasher user manual
PROBLEM POSSIBLE CAUSES WHAT TO DO
19
Noise!
Suds in the Tub!
• Some audible sounds
are normal
• Utensils are not secure
in the baskets or
something small has
dropped into the
basket and is loose
• Motor Hums
• Improper detergent
• Sound from soft food shredding
action and detergent cup opening.
This is not a problem.
• Ensure everything is placed securely
in the dishwasher.
• Dishwasher has not been used
regularly. If you do not use it often,
remember to set it to fill and pump
out every week. (See Wash Cycle
table). This will h elp keep the seal
moist.
• Use only special dishwasher
detergent to avoid suds.
• Spilled rinse agent
• Always wipe up rinse agent spills
immediately.
Stained tub
Interior!
Dishes are not
dried!
• Detergent with
colorant was used
• Rinse agent dispenser
is empty
• Make sure you use detergent without
colorant.
• Make sure that the rinse agent
dispenser is filled.
Dishes and
Flatware not
• Improper program • Select stronger program.
Clean!
19
Page 20
BAUMATIC BDW2W / BDW2SS dishwasher user manual
g
g
PROBLEM POSSIBLE CAUSES WHAT TO DO
20
Spots and Filmin
on Glasses and
Flatware!
Cloudiness on
glass!
• Improper rack loading
To remove spots from glassware:
• Extremely hard water
• Low inlet temperature
• Overloading the
dishwasher
• Improper loading
• Old or damp powder
detergent
• Empty rinse agent
dispenser
• Incorrect dosage of
detergent
• Combination of soft
water and too much
detergent
1. Take all metal utensils out of the
dishwasher.
2. Do not add detergent.
3. Choose the longest cycle.
4. Start the dishwasher and let it to run for 18
- 22 minutes, then it will be in the main wash.
5. Open the door and pour 2 cups of white
vinegar into the bottom of the dishwasher.
6. Close the door and let the dishwasher
complete the cycle.
7. If the vinegar does not work, repeat as
above, only use ¼ cup (60ml) of citric acid
crystals instead of vinegar.
• Make sure there are no large dishes
blocking the action of the detergent
dispenser and the spray arms.
• Use less detergent if you have soft
water and select a shorter cycle to
clean the glassware.
Yellow or brown
film on inside
surfaces!
White film on
inside surface!
Deter
ent cup lid
won’t latch!
• Tea or coffee stains
• Iron deposits in water
can cause an overall
film
• Hard water minerals
• Button is not in the
‘OFF’ position
• Use a solution of ½ cup of bleach and
3 cups warm water to remove the
stains by hand. Rinse thoroughly.
• You have to call a water softener
company for a special filter.
• To clean the interior, use a damp
sponge with dishwasher detergent
and wear rubber gloves. Never use
any other cleaner than dishwasher
detergent for the risk of foaming or
suds.
• Turn the Button to ‘OFF’ position and
slide the door latch to the left.
20
Page 21
BAUMATIC BDW2W / BDW2SS dishwasher user manual
PROBLEM POSSIBLE CAUSES WHAT TO DO
21
Detergent left in
dispenser cups!
Steam!
Black or grey
marks on dishes!
Water standing in
the bottom of the
tub!
• Dishes block detergent
cups
• Normal phenomenon
• Aluminium utensils
have rubbed against
dishes
• This is normal
• Reload the dishes properly.
• There is some steam coming through
the vent by the door latch during
drying and water draining.
• Use a mild abrasive cleaner to
eliminate those marks by hand.
• A small amount of clean water
around the outlet on the tub bottom
at the back of the tub keeps the
water seal lubricated. No action
needed.
Dishwasher leaks!
• Be careful not to overfill the rinse aid
dispenser.
• Overfilled dispenser or
rinse aid has spilled
• Dishwasher isn’t level • Make sure the dishwasher is level.
• 3-in-1 Tablets
• Spilled rinse aid could cause
oversudsing and lead to overflowing.
• Wipe away any spills with a damp
cloth.
• Make sure if you’re using 3-in-1
tablets that you do not put rinse aid
and salt into the appliance as well.
21
Page 22
BAUMATIC BDW2W / BDW2SS dishwasher user manual
g
PROBLEM POSSIBLE CAUSES WHAT TO DO
• Level appliance & ensure top screws
• Appliance not level
attaching appliance to work surface
are not lifting the weight of the
dishwasher.
22
Door poppin
open!
• Door not fitted
correctly
• Door tension not
adjusted
• Door lock failure –
Weight of door
• See pages 26-27 for information
about correct fitting of door.
• Adjust tension page 28.
• Refer to service. Maximum weight
of the door is 4.5 kg - 5 kg.
IF OVERFLOW OCCURS, TURN OFF THE MAIN WATER SUPPLY BEFORE CALLING A SERVICE
TECHNICIAN. IF THERE IS WATER IN THE BASE OF THE TANK P AN BECA USE OF AN O VERFILL OR
SMALL LEAK, THE WATER SHOULD BE REMOVED BEFORE RESTARTING THE DISHWASHER.
WARNING!
22
Page 23
BAUMATIC BDW2W / BDW2SS dishwasher user manual
23
DISHWASHER CHARACTERISTICS
The BAUMATIC BDW2W / BDW2SS dishwasher models are based firmly on convenience.
Apart from having the same general workings as other household dishwashers, they
have several extra features.
Performance of
Dishwasher -
a B rated wash performance, B rated drying
performance and A rated energy efficiency.
Your dishwasher has
basket -
you can load the dishes by adjusting the
basket.
Adjustable upper
Even if the dishware is lar ge,
Overflow protection - Your
dishwasher has an overfill protection program
which could automatically shut off the inlet
valve and start the drain pump if the water
Overflows.
Indicator -
this signal will light up on the control panel
to alert you to top the salt level up so the
machine can keep at its optimum
performance level.
Salt Warning
If the salt is running lo w,
Rinse aid Warning
Stainless steel tub-
You need not worry about stains to the tub.
Indicator -
low, this signal will light up on the control
panel, alerting you to top the rinse aid level
up so the machine can keep at its optimum
performance level.
If the rinse aid is running
7 wash programs -
You can choose desired program according
to the soiled level. Such as, intensive
wash, normal wash, economy, rinse, glass,
rapid and pre-wash, etc.
12 place settings -
Normal wash load of 12 place settings.
Broad applied
voltage -
(alternating current) voltage. Please be
aware that this will make its operation
vulnerable to uneven current in your home
and power surges.
This appliance uses AC
INSTALLATION INSTRUCTIONS
23
Page 24
BAUMATIC BDW2W / BDW2SS dishwasher user manual
24
NOTE: APPLIANCE SHOULD ONLY BE FITTED BY
INSTALLING YOUR DISHWASHER
a) PREPARATION
Before you install your appliance, make sure that the place you have chosen to
fit it is:
• Near the existing power socket.
• So that you can choose one side of the cabinet cavity to easily
connect the dishwasher’s drain hoses.
• Near your sink so you have easy access to the water inlet and drain
hoses.
• If dishwasher is to be installed at the corner of cabinet area, make
A TRAINED TECHNICIAN
sure you have enough space when the door is opened.
Is structured so that you have less than 5 mm between the top of the
•
dishwasher and cabinet. Also check that the outer door is aligned to
cabinet. (See figures below).
b) PLACING AND FITTING YOUR DISHWASHER’S
OPTIONAL FURNITURE DOOR
1 The furniture door (an optional accessory fitted to match your kitchen décor
24
Page 25
BAUMATIC BDW2W / BDW2SS dishwasher user manual
available from your kitchen unit dealer) can be attached to the front of the
dishwasher according to the following diagram. (Measurement is in millimetres):
•
•
NOTE: THE MAXIMUM WEIGHT OF THE DOOR IS 4.5-5 KILOGRAMS. IN THE FIGURE
BELOW
, IT IS REFERRED TO AS ‘THE AESTHETIC PANEL’.
• DO NOT INSTALL WITH SCREWS THROUGH THE DOOR ONLY.
• ONLY USE THE 2 SCREW HOLES AND BRACKETS AVAILABLE.
• FAILURE TO INST ALL DOOR CORRECTLY CAN CAUSE PROBLEMS WITH THE
DOOR / PERFORMANCE OF YOUR APPLIANCE.
25
Installing the furniture door
2 Install the hook on the furniture door and put the hook into the slot of the outer
door of the dishwasher
Back of the furniture door Front of the dishwasher door
.
25
Page 26
BAUMATIC BDW2W / BDW2SS dishwasher user manual
26
After positioning the panel, fix it onto the outer door using screws and bolts (see above
figure).
1. Take away the cover. 2. Affix the screw. 3. Replace the cover.
c) TENSION ADJUSTMENT OF THE DOOR SPRING
Your dishw asher’s outer door is attached to springs. These are set at the factory to
ensure they’re at the proper tension so that the door can open and close smoothly
and conveniently.
Note: If you have installed a cover panel ov er the door, you will have to adjust the
26
Page 27
BAUMATIC BDW2W / BDW2SS dishwasher user manual
27
door spring tension.
• Using an Allen key, rotate the adjusting screw to tighten or slacken
the steel cable. You must do this or damage to your dishwasher
may result.
The door’s spring tension is good when the door remains horizontal in the fully
opened position, yet rises to a close with the slight lift of a finger.
Warning: failure to adjust the door spring
tension could result in damage to your
dishwasher!
d) NEXT, CONNECT THE WATER INLET
BELOW):
Connect the cold water supply hose to a threaded
¾ inch connector and make sure that it is
fastened tightly in place.
Attach tube C
If the water pipes are new or have not been used
for a long time, let the water run to make sure
that the water is clear and free of impurities. The
water inlet may get blocked and damage the
appliance.
to the cold water supply A.
(SEE FIGURE
Make sure the water pressure is the same a s the
range indicated on the data tag.
DO NOT CONNECT TO THE HOT
If your appliance is fitted with an aqua stop
system then this must be fitted vertically
(pointing upwards) not downwards or sideways
27
WATER SYSTEM!
.
Page 28
BAUMATIC BDW2W / BDW2SS dishwasher user manual
28
e) THEN, CONNECT THE DRAIN HOSE (SEE FIGURE
BELOW):
The curved end of the drainage hose should be hooked into the drainage stand pipe or , alternatively , over the
edge of your sink.
During installation, make sure that:
• The drainage hose is not kinked or crushed.
• The hose end, relative to the top surface of the dishwasher (SEE FIGURE BELOW), must be placed
at a height between 32cm and 80cm.
• The end of the hose must never be immersed in water.
• The drainage hose must not be extended to more that a maximum length of 1 metre. The
extension must have the same internal diameter. Furthermore, the maximum height at which the
hose end can be placed (in the case of an extended tube) must be reduced from 80cm to 50cm.
• The drainage stand pipe must have an internal diameter of no less than 4 cm.
NOTE: DO NOT EXTEND THE DRAIN HOSE AS THIS CAN AFFECT THE PERFORMANCE OF
THE DISHWASHER.
28
Page 29
BAUMATIC BDW2W / BDW2SS dishwasher user manual
29
f) NOW YOU ARE READY TO CONNECT THE
POWER CORD.
WARNING!
ELECTRICITY CAN BE DANGEROUS. PLEASE READ THE FOLLOWING
CAREFULLY
:
ELECTRICAL CONNECTION
Electrical Requirements
The dishwasher is designed for operation on an adequately wired individual 220-240V AC, 50Hz
system. The required fuse rating is 13amp. Fused electrical supply is required – copper wire
only. Time delay fuse or circuit breaker is recommended. Make sure that this appliance
runs off its own separate circuit. Outlet should be placed in adjacent cabinet.
WARNING – ENSURE PROPER GROUND EXISTS BEFORE
USE.
After making sure that the voltage and the frequency values for the current in your home
correspond to those on the rating plate and that the electrical system is sized for the maximum
voltage on the rating plate, insert the plug into an electrical socket which is earthed properly. If
the electrical socket to which the appliance must be connected is not right for the plug, replace
the socket, rather than using adaptors of the like as they could cause overheating and fire.
g) NOW, PUT THE DISHWASHER ON THE SLIDE
RAILS (These are supplied so your appliance can be pushed into place
easily and to protect your floor surface from pressure points). See figure at
bottom of page.
29
Page 30
BAUMATIC BDW2W / BDW2SS dishwasher user manual
E
A
T
A
y
30
h) THEN, APPLY THE CONDENSATION STRIP.
The Condensation Strip must be fitted to the
underside of the worktop above your dishwasher
to protect it against any moisture. Its purpose is
to deflect steam rising from your appliance to
protect your worktop’s underside.
• The strip is located inside your
dishwasher.
• Ensure the surface is clean prior to
sticking to underside of the worktop.
• Separate the backing paper from the
strip.
• Stick to the underside of the worktop.
Note
: Failure to attach strip could
result in damage to the underside of
your work surface!
i) NOW YOU ARE READY TO PUSH THE DISHWASHER
INTO POSITION
NOTE –
MAKE SURE YOU HAVE TH
DISHWASHER ON ITS SLIDE RAILS
(See figure on right).
THEN MOVE IT INTO THE CABINET
RECESS (AS PICTURED ON RIGHT).
ENSURING THAT IT IS BACKED UP
GAINST THE WALL. ATTACH THE
FURNITURE DOOR (STEP 1 AS
PICTURED ON RIGHT) IF YOU HAVE
NOT ALREADY DONE SO.
YOU ARE NOW READY TO SECURE
YOUR APPLIANCE TO THE CABINE
REA (STEP 5 AS PICTURED ON
RIGHT).
*
Note: The ‘Aesthetic Panel’ is
the furniture door which you ma
have already installed (see pp.
25-26).
j) NOW GET THE DISHWASHER LEVEL.
NOTE: YOUR
DISHWASHER MUST BE
LEVEL FOR PROPER
DISH RACK OPERATION
(SEE FIGURE BELOW):
AND WASH
PERFORMANCE.
WARNING!
30
Page 31
BAUMATIC BDW2W / BDW2SS dishwasher user manual
BE CAREFUL WHILE YOU ARE
LEVELLING YOUR DISHWASHER
IN PLACE – IT COULD TIP OVER
AND INJURE YOU!
CONSULT THE FIGURE BELOW
FOR HELP!
31
THE REAR FEET CAN BE ADJUSTED FROM THE FRONT OF THE DISHWASHE R BY TURNING THE SC REWS ON THE LEFT
AND RIGHT HAND SIDES OF THE CABINET. TO ADJUST THE FRONT FEET, USE A WRENCH / SPANNER AND TURN THE
FRONT FEET UNTIL THE DISHWASHER IS LEVEL (PLEASE SEE ‘REMARK B’ IN THE ABOVE FIGURE).
WHEN YOU ROTATE THE ADJUSTER POLE CLOCKWISE, THE BACK FOOT WILL DRIVE UP THE DISHWASHER.
(PLEASE SEE ‘REMARK A’ IN THE ABOVE FIGURE).
k) THE DISHWASHER MUST NOW BE SECURED IN
PLACE
SURFACE. REMEMBER THAT YOUR DISHWASHER’S WEIGHT MUST REST ON ITS FEET. THE
FASTENINGS AT ITS TOP ARE TO GIVE STABILITY AND WILL PREVENT IT FROM TIPPING
FORWARD:
. THERE ARE TWO WAYS TO DO THIS, DEPENDING ON YOUR TYPE OF WORK
NORMAL WORK SURFACE
WOODSCREWS ENSURING THAT THE DISHWASHER CAN OPEN AND CLOSE COMFORTABLY.
MARBLE OR GRANITE WORK TOP
THE TOP OF THE DISHWASHER TO THE UNDERSIDE OF THE SPECIAL WORK SURFACE. BECAUSE OF
THIS, YOU WILL HAVE TO SECURE THE BRACKET TO THE SIDE PANELS OF THE DISHWASHER
CABINET AND SECURE THE DISHWASHER TO THE FURNITURE HOUSING. PUT THE RUBBER CAP
OVER THE SCREW.
NOTE: DO NOT PUT ANY WEIGHT FROM THE DISHWASHER ON THESE SCREWS – ENSURE
YOUR DISHWASHER’S WEIGHT RESTS ENTIRELY ON ITS FEET.
- SECURE TO THE WORK SURFACE’S UNDERSIDE BY USING TWO
– FOR THESE WORKTOPS, YOU WILL NO T BE ABLE TO SECURE
31
Page 32
BAUMATIC BDW2W / BDW2SS dishwasher user manual
FINAL CHECKLIST BEFORE OPERATING
NOTE: BEFORE
PLEASE MAKE SURE YOU HAVE CHECKED
• WHETHER THE DISHWASHER IS LEVEL AND FIXED.
• WHETHER THE INLET VALVE IS OPENED.
• WHETHER THERE IS LEAKAGE AT THE
• WHETHER THE WIRES ARE TIGHTLY CONNECTED.
• WHETHER THE POWER IS SWITCHED ON.
• WHETHER THE INLET AND DRAIN HOSES ARE
• WHETHER ALL PACKING MATERIALS & PRINTED
YOU START USING YOUR DISHWASHER,
:
CONNECTIONS OF THE CONDUCTS.
KNOTTED / KINKED.
MATTER HAVE BEEN REMOVED FROM THE
DISHWASHER.
32
PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE
BAUMATIC LTD. - CONDITIONS OF GUARANTEE.
Dear Customer,
32
Page 33
BAUMATIC BDW2W / BDW2SS dishwasher user manual
The conditions of guarantee which apply to your Baumatic appliance are as follows: This product is
guaranteed for 12 months from the date of original purchase.
Baumatic Ltd will repair any defect that arises due to faulty materials or workmanship free of charge during
this period.
In addition, your appliance is covered by a 5 year parts warranty. Baumatic Ltd will provide free of charge
the parts required to repair the appliance, only if they are fitted by a Baumatic engineer, for any defect that
arises due to faulty materials or workmanship within a period of 5 years from the original purchase date.
An additional and annually renewable insurance scheme for labour is available should you wish to extend the
warranty period.
Should any person other than an authorised representative of Baumatic Ltd interfere with the appliance, the
policy is negated and Baumatic Ltd will be under no further liability.
The guarantee covers the appliance for normal domestic use only, unless otherwise stated.
Any claims made under the terms of the guarantee must be supported by the original invoice/bill of sale
issued at the time of purchase.
This guarantee is transferable only with the written consent of Baumatic Ltd.
If the appliance fails and is considered either not repairable or uneconomical to repair between twelve months
and five years from purchase date, a free of charge replacement will not be offered.
The guarantee for any replacement will only be for the remainder of the guarantee on the original product
purchased.
This guarantee does not cover:
• Sinks and taps
• Failure to comply with the manufacturer’s instructions for use.
• The replacement of cosmetic components or accessories.
• Accidental damage or wilful abuse.
• Subsequent loss or damage owing to the failure of the appliance or electrical supply.
• Incorrect installation.
• Losses caused by Acts of God, civil war, failure to obtain spare parts, strikes or lockouts.
• Filters, fuses, light bulbs, external hoses, damage to bodywork, paintwork, plastic items, covers,
baskets, trays, shelves, burner bases, burner caps, decals, corrosion, rubber seals, refrigeration
system blockage.
In the course of the work carried out it may be necessary to remove the appliance from its operating position.
Whilst all reasonable care will be taken, Baumatic L td cann ot accept r esp onsib i lity for d amage susta in ed to
any property whatsoever in this process.
This guarantee is in addition to and does not diminish your statutory or legal rights.
33
Contacting Baumatic.
SALES
TEL: 0118 933 6900
FAX: 0118 931 0035
SERVICE
For mainland UK and Northern Ireland, please co nta ct one of the above numbers for further information or
any other query you may have.
For ROI (Republic of Ireland), please contact one the numbers below:
TEL: 01-4030501 FAX: 01-4030503
Thank you for buying Baumatic.
TEL: 0118 933 6911
FAX: 0118 986 9124
SPARES
TEL: 0118 933 6922
FAX: 0118 933 6942
TECHNICAL / ADVICE
TEL: 0118 9336933
FAX: 0118 9336942
33
Page 34
BAUMATIC BDW2W / BDW2SS dishwasher user manual
Baumatic Ltd
Make-up for your kitchen
Headquarters
Baumatic Buildings,
6 Bennet Road,
RG2 0QX, United Kingdom
Sales Telephone
+44 118 933 6900
+44 118 931 0035
Service Telephone
+44 118 933 6911
+44 118 986 9124
Spares Telephone
+44 118 933 6922
Technical / Advice Telephone
+44 118 933 6933
sales@baumatic.co.uk
technical@baumatic.co.uk
Http (Internet site):
www.baumatic.com
Baumatic UK/cod. 1230000666
This appliance is marked according to the European
Directive 2002/96/EC on Waste Electrical and Electronic
Equipment(WEEE).
This guideline is the frame of a Europeanwide validity of return
and recycling on Waste Electrical and Electronic Equipment.
Baumatic Ltd.
Reading,
Berkshire
Sales Fax
Service Fax
E-mail
:
34
34
Page 35
BAUMATIC BDW2W / BDW2SS dishwasher user manual
35
35
Page 36
BAUMATIC BDW2W / BDW2SS dishwasher user manual
36
36
Loading...