Baumatic BDW1460 Instruction manual
BDWI460 45 cm Fully
integrated full height
electronic dishwasher
USER MANUAL FOR YOUR BAUMATIC
BDWI460 45 cm Fully
integrated full height electronic
dishwasher
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
JW 20/11/12
2
Contents
Environmental note 4
Important safety information 5 – 7
Specifications 8 – 10
Product and aperture dimensions 8
Product specifications 8 – 9
Electrical details 9
Description of the appliance 10
Control panel 10 - 10
Using your dishwasher 11 - 23
Before first use 11
Filling with dishwasher salt 11 – 12
Setting the water softener level 12 - 13
Filling with rinse aid 13
Setting the rinse aid level 14
Filling with dishwasher detergent 14 - 15
Loading the upper basket 15
Adjusting the upper basket 16 - 17
Loading the lower basket 17 - 18
The cutlery basket 18
Loading dishes and cutlery 19 - 20
Program table 20 - 21
Setting a wash program 21 - 22
Changing a wash program 22
At the end of a wash program 22
Adding an item to the wash 23
Setting a delay start 23
Rinse aid and salt indicator neons 24
Saving energy using your dishwasher 24
Cleaning and maintenance 25 - 28
The filter system 25
Cleaning the filters 26
Cleaning the spray arms 27
Cleaning the control panel 27
Cleaning the door 27
Error code failure system 28 – 29
General troubleshooting 29 – 30
Installation 31 - 40
Aperture requirements 31 - 32
Preparing and connecting the furniture door 33 - 34
Adjusting the tension of the door spring 35
Connecting to the mains water supply 36
Connecting to the water outlet 36
Connecting to the power supply 37
Applying the condensation strip 38
Positioning the dishwasher 39
Levelling the appliance 39
Securing the dishwasher 40
Before first use 40
My appliance isn’t working 41
Baumatic consumables 42
Technical data 43
Contact details 47
3
ENVIRONMENTAL NOTE
Note
disconnect it from the power supply. Cut off and render any plug
useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person. Disable
the door lock to make sure that children cannot get stuck inside
the appliance.
: Before discarding an old appliance, switch off and
o The packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
o Please discard all packaging material with due regard for the
environment.
4
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
booklet, please contact the Baumatic Advice Line.
General Safety
o Repairs to your appliance must only be carried out by a
Baumatic engineer or one of its authorised service agents. Any
attempt by an inexperienced person to repair the appliance,
could result in injury or damage to your dishwasher.
o If you notice that the mains cable is damaged. The appliance
must not be used. The same applies if you notice that the
worktop, control panel or base area is damaged. As this could
allow access to the internal components of the machine.
o The appliance should be turned off and isolated from the mains
supply, before either cleaning or maintenance work is attempted.
o The mains cable must not be used to pull the plug out of the
electrical socket.
o The machine should not be sprayed with water.
o The external surface of the appliance may become hot whilst
your dishwasher is in use.
o It is possible for small animals to chew either mains cables or
water hoses, which could cause an electric shock hazard.
Installation
o The installation instructions contained within this user manual
should be followed.
o It is obligatory for the completed installation to comply with all
relevant building regulations and local water authority
requirements.
o Before the first use of the appliance, you should follow the
steps listed in the “Before first use” section on page 11
and page 40 of this manual.
5
o Care should be taken not to trap the power supply cable
underneath the appliance whilst installing it.
o No attempt should be made to alter or modify the specifications
of this appliance.
In daily use
o This appliance is only designed to wash normal domestic wash
loads. If you use your dishwasher in any other way or it is
incorrectly used, then Baumatic accepts no liability for any
damage that might be caused and any guarantee will be void.
o It is recommended that the appliance is unplugged and the
water supply is turned off after the machine is used.
o The detergents, rinse aid and salt that you place in this appliance
should be suitable for automatic dishwashers. With regards to
dosage levels, the detergent manufacturer’s recommendations
should be followed.
o Sharp knifes or ones with long blades are a potential safety
hazard when placed in an upright position in the cutlery basket.
We would recommend that these items are placed horizontally in
the upper basket.
o You should not wash any items that have come into contact
with corrosive, acidic or alkaline chemicals, paint, petrol, iron or
steel debris.
o You should not open the door whilst the appliance is set on a
wash program. Depending on which stage that the wash
program is at, hot water could escape the machine.
o You should not leave the door of the appliance open, unless
you are loading or unloading the dishwasher.
o You should not stand or sit on the door when it is open.
6
Child Safety
o Your dishwasher should only be used by adults. You should not
allow children in the area of the machine unsupervised. You
should not let them touch the controls or play with the appliance.
o It could be possible for a child or pet to gain access to the
dishwasher if the door is left open. Therefore please check the
inside of the appliance before setting it on a wash cycle.
o Any packaging that is removed from the machine should be kept
away from children.
o All detergents should be kept out of children’s reach in a safe
place.
o Some water will remain inside the dishwasher when it has
completed a wash cycle. This water is not suitable for drinking
and may contain residues from the detergents that are used in
the appliance.
Declaration of conformity
This appliance complies with the following European Directives:
-73/23 dated 19/02/1973 Low Voltage Directive and subsequent
modifications.
-89/336 dated 03/05/1989 Electromagnetic Compatibility Directive and
subsequent modifications.
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate of your dishwasher is
located on the right hand side of the drop down door.
Model Number ……………………………….
Serial Number ……………………………….
Date of Purchase ……………………………….
7
Specifications
Product dimensions
Height: 815 - 865 mm
Width: 448 mm
Depth: 550 mm
Aperture dimensions
Height: 815 mm (min)
Width: 450 mm
Depth: 580 mm (min)
Product specifications
o 10 Place settings
o 6 functions: Normal
Intensive
Economy
Glass
Rapid
1 Hour
o 6 temperatures: 40°C, 45°C, 50°C, 55°C, 60°C, 65°C
8
o Delay timer
o LED display
o Self-cleaning stainless steel micro-filter
o Anti-leak device
o Anti-flood device
o Height adjustable upper basket
o Collapsible plate racks
o Pull out cutlery drawer
o Adjustable feet
o Residual drying
o Concealed heating element
o Half load
o Low water consumption (9 litres)
Energy efficiency details
Energy efficiency class: A+
Washing performance class: A
Drying performance class: A
Power consumption
Off mode: 0.45 W
Left on mode: 0.49 W
Electrical details
Rated voltage: 230 Vac 50 Hz
Supply connection: 13 A (double pole switched fused outlet with
3 mm contact gap)
9
Description of the appliance
1) Top spray arm
2) Cutlery rack
3) Upper basket
4) Inner pipe
5) Lower basket
6) Salt dispenser / Water softener
Control panel
7) Detergent dispenser
8) Cup shelf
9) Bottom spray arm
10) Main filter
11) Inlet pipe connector
12) Drain pipe connector
1) ON/OFF button
2) Delay start button
3) ON/OFF indicator neon
4) Delay start indicator neons
5) Rinse aid and salt indicator neons
6) Half-load indicator
7) Program indicator neons
8) Half-load button
9) Program selection button
10
Using your dishwasher
Before first use
o Install the appliance as per the installation instructions contained
within this booklet.
o Add 1.5Kg specialist dishwasher salt to the dishwasher water
softener compartment and then fill with tap water. After this you
should set the water softener level.
o Fill the rinse aid dispenser and then set the rinse aid dosage.
Filling with dishwasher salt
IMPORTANT: You should only use salt that is specially
designed for use in a dishwasher. If any other type of salt is
used in the appliance (in particular table salt), it will damage
the water softener.
o Ideally you should fill the water softener with salt, just before you
are about to run a wash program. This will help to clear any salt
that may have overflowed from the water softener during the salt
filling process.
o Open the door of the dishwasher and
then remove the lower basket. The
basket should be empty when you
remove it.
o Turn the water softener cap
anticlockwise and remove it.
IMPORTANT: It is only necessary to do this when you fill the
container with salt for the first time.
o Pour salt into the water softener
compartment using the funnel that is
supplied with the appliance. You should
add approximately 1.5 kg of salt into the
water softener.
o Then pour tap water into the water
softener until it fills.
11 12
o It is perfectly normal for a small amount of water to come out of
the water softener compartment.
o Refit and fully tighten the water softener cap.
o The salt required warning light will go out approximately 2-6 hours
after you have filled the water softener with salt. When the salt
indicator neon lights on the control panel in the future, you should
follow the filling with dishwasher salt procedure again.
o IMPORTANT: You do not need to pour additional water into
the container when you subsequently fill the water softener
with salt.
Setting the water softener level
It is possible to regulate the amount of salt that the water softener will
release during a wash cycle. The water softener should be set to a
level that is appropriate for the hardness of your water (please refer to
the table below).
WATER HARDNESS
Clarke
degrees
0-6 0-5 0-9 Rapid 0 /
7-14 6-11 10-20 1 Hour 20 60
15-21 12-17 21-30 Rapid + 1 Hour
22-28 18-22 31-40 Glass 40 40
29-42 23-34 41-60 Rapid + Glass 50 30
43-69 35-55 61-98 1 Hour + Glass
dH°
German
degrees
°TH
French
degrees
Water
hardness
selection
Grams of
salt used
per cycle
30 50
60 20
Approximate
number of cycles
per 1kg of salt
To alter the amount of salt that is released by the water softener, you
should:-
o Open the door and switch on the appliance.
o Press and hold the program button for more than 5 seconds to
enter the water hardness selection mode. You must enter the water
hardness selection mode within 60 seconds of turning on the
appliance.
o The salt and rinse aid neons will flash on the control panel
o Press the program button to scroll through the water harness
selection options. Please see the table above for full details.
o When you have selected the correct water hardness level, you
should press the power button to complete set up.
o IMPORTANT: If you are using 3 in 1 dishwasher tablets and live in
a medium or hard water area, then you should still fill the water
softener with salt.
Filling with rinse aid
The rinse aid is released during the final rinse and it helps
to prevent water from forming droplets on your dishes.
These droplets will lead to spots and streaks being left on
items after the wash program has completed.
o Your dishwasher is designed to utilise liquid rinse aid.
o The rinse aid dispenser is located inside the drop down door, next
to the detergent dispenser.
To access the rinse aid dispenser, you should turn the cap
anticlockwise and it will pop out of the hole (1). Then slowly pour in
liquid rinse aid (2), the rinse aid dispenser will hold approximately 110
ml of rinse aid.
o You should continue to fill with rinse aid, until the level indicator
turns completely black.
o Be careful not to overfill the dispenser, as this could cause
oversudsing when a wash program is selected. Wipe away any rinse
aid excess or spillages with a damp cloth.
o Replace the cap and turn it clockwise until it locks into position (3).
o You should refill the rinse aid dispenser when the rinse aid indicator
neon lights on the control panel.
o IMPORTANT: If you are using 3 in 1 dishwasher tablets then you
should still fill the rinse aid dispenser.
13
Setting the rinse aid level
The amount of rinse aid that the dishwasher requires also depends on
the hardness of your water. You should experiment with the rinse aid
setting, until you find a level that gives the best results.
o On the first wash cycle, we would
recommend that the rinse aid level is set
to number 4.
o If you get water spots and poor drying
performance, then you should turn the
arrow anticlockwise and increase the
setting to the next number.
o You should continue to adjust the rinse aid level upwards until
you get no water spots.
o If you get cloudiness or streaking on your dishes, the rinse aid
level is set too high and it is causing foaming during the wash
cycle. Turn the arrow clockwise and lower the setting to the next
number.
Filling with dishwasher detergent
The detergent dispenser must be refilled at the start of each wash
cycle (apart from the Rinse wash program).
o Open the lid that closes over the detergent dispenser (1) and
place the detergent inside of the dispenser (2).
14
o The left section displayed in the
diagram (A) is for the main wash
cycle detergent. Only one
detergent tablet should be placed
in the dispenser at any one time.
If you are using detergent powder
or liquid, you should follow the
detergent manufacturer’s
recommendations.
o The right section displayed in the diagram (B) can have separate
detergent placed in it for any wash cycle that has a pre-wash
element to it, however this is optional. This must be a liquid or
powder detergent, not another detergent tablet.
o Shut the detergent dispenser lid firmly to ensure that it clips into
place
o At the relevant stage of a wash cycle the lid will open and the
tablet/powder/liquid will enter the dishwasher.
Loading the upper basket
The upper basket is most suited to washing delicate and light
dishware, such as glasses, cups & mugs, saucers, plates, bowls and
shallow pans (that are not heavily soiled).
1. Cups
2. Saucers
3. Glasses
4. Dessert dishes
5. Serving bowl
o You should position the dishes and cookware in such a way that
they are not moved by the spray of water during the wash cycle.
o Use the diagram above as a guide to the most appropriate way to
load the upper basket.
15
Loading...