Before using the appliance
carefully read these safety
instructions.
Keep them close at hand for
future reference.
These instructions and the
appliance itself provide
important safety warnings, to
be observed at all times.
The manufacturer declines any
liability for failure to observe
these safety instructions,
for inapropriate use of the
appliance or incorrect setting
of controls.
Remove the transport bolts.
The washing machine is tted
with transport bolts to avoid
any possible damage to the
interior during transport.
Before using the machine, it is
imperative that the transport
bolts are removed.After their
removal, cover the openings
with the 4 enclosed plastic
caps.
Never open the door forcibly
or use it as a step.
SAFETY WARNINGS
Very young (0-3 years) and
young children (3-8 years)
shall be kept away from the
appliance unless continuously
supervised.
Children from 8 years old
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge
can use this appliance only if
they are supervised or have
been given instructions on
safe use and understand the
hazards involved. Children
must not play with the
appliance. Cleaning and
user maintenance must not
be carried out by children
without supervision.
PERMITTED USE
CAUTION: The appliance is
not intended to be operated
by means of an external timer
or separate remote controlled
system.
This appliance is solely for
domestic, not professional use.
Do not use the appliance
outdoors.
Do not store explosive or
ammable substances such
as aerosol cans and do not
place or use gasoline or other
ammable materials in or
near the appliance: a re may
break out if the appliance is
inadvertently switched on.
This washing machine is
exclusively destined to treat
machine washable laundry in
quantities which are usual for
private households.
INSTALLATION
The appliance must be
handled and installed by
two or more persons. Use
protective gloves to unpack
and install the appliance.
Installation and repairs must
be carried out by a qualied
technician, in compliance
with the manufacturer’s
instructions and local safety
regulations. Do not repair
or replace any part of the
appliance unless specically
stated in the user manual.
Children should not perform
installation operations.
Keep children away during
installation. Keep the
packaging materials (plastic
bags, polystyrene parts, etc.)
out of reach of children, during
and after the installation.
After unpacking the appliance,
make sure that it has not been
damaged during transport. In
the event of problems, contact
the dealer or your nearest
After-sales Service.
The appliance must be
disconnected from the power
supply before any installation
operation.
During installation, make
sure the appliance does not
damage the power cable.
Only activate the appliance
when the installation has been
completed.
After installation of the device
to wait a few hours before
starting it, to acclimatize to the
environmental conditions of
the room.
Do not install your appliance
where it may be exposed to
extreme conditions, such
as: poor ventilation, high
temperature or below 5°C or
above 35°C.
When installing the appliance
make sure that the four feets
are stable and resting on
the oor, adjusting them as
required, and check that the
appliance is perfectly level
using a spirit level.
In case of wooden or so-called
“oating oors” (for instance
certain parquet or laminate
oors), place the appliance
5
on a sheet of plywood at least
60 x 60 cm wide/ deep and
at least 3 cm thick which is
secured to the oor.
Use only new hoses to connect
the appliance to the water
supply. Used hoses must
not be used and should be
discarded.
Move the appliance without
lifting it by the worktop.
Connect the water inlet
hose(s) to the water supply
in accordance with the
regulations of your local water
company.
For models dedicated only for
cold water: Do not connect to
the hot water supply
For models with hot ll: the
hot water inlet temperature
must not exceed 60 °C.
Make sure that the ventilation
openings in the base of your
washing machine (if available
on your model) are not
obstructed by a carpet or other
material.
The supply water pressure
must be in range 0.1 -1 MPa.
If you want to place a dryer
on top of your washing
machine, rst contact our
After-Sales Service or your
specialist dealer to verify if
this is possible. This is only
admitted if the dryer is xed
on the washing machine by
using an appropriate stacking
kit available through our AfterSales Service or your specialist
dealer.
ELECTRICAL WARNINGS
For installation to comply with
current safety regulations,
an omnipolar switch with
minimum contact gap of
3 mm is required and the
appliance must be earthed.
If the power cable is damaged,
replace with an identical one.
The power cable must only
be replaced by a qualied
technician in compliance with
the manufacturer instruction
and current safety regulations.
Contact an authorized service
center.
If the tted plug is not suitable
for your socket outlet, contact
a qualied technician.
The power cable must be
long enough to connect the
appliance, once tted in its
housing, to the main power
supply. Do not pull the power
supply cable.
Do not use extension leads,
multiple sockets or adapters.
Do not operate this appliance
if it has a damaged mains
cord or plug, if it is not
working properly, or if it has
been damaged or dropped.
Keep the cord away from hot
surfaces.
The electrical components
must not be accessible to the
user after installation.
Do not touch the appliance
with any wet part of the body
and do not operate it when
barefoot.
CORRECT USE
Do not exceed the maximum
load allowed. Check the
maximum load allowed in the
programme chart.
Turn o the tap when not in
use.
Do not use any solvents
(e.g. turpentine, benzene),
detergents containing solvents,
scouring powder, glass or
general purpose cleaners,
and ammable uids; do not
machine wash fabrics that have
been treated with solvents or
ammable liquids.
CLEANING AND
MAINTENANCE
Never use steam cleaning
equipment.
Wear protective gloves for
cleaning and maintenance.
The appliance must be
disconnected from the
power supply before any
maintenance operation.
6
SAFEGUARDING
THE ENVIRONMENT
EN
DISPOSAL OF PACKAGING
MATERIALS
The packaging material is 100%
recyclable and is marked with
the recycle symbol . The
various parts of the packaging
must therefore be disposed
of responsibility and in full
compliance with local authority
regulations governing waste
disposal.
SCRAPPING OF HOUSEHOLD
APPLIANCES
When scrapping the appliance,
make it unusable by cutting o
the power cable and removing the
doors and shelves (if present) so that
children cannot easily climb inside
and become trapped.
This appliance is manufactured
with recyclable or reusable
materials. Dispose of it in
accordance with local waste
disposal regulations.
For further information on the
treatment, recovery and recycling
of household electrical appliances,
contact your competent local
authority, the collection service for
household waste or the store where
you purchase the appliance.
This appliance is marked in
compliance with European Directive
2012/19/EU, Waste Electrical and
Electronic Equipment (WEEE).
By ensuring this product is disposed
of correctly, you will help prevent
potential negative consequences for
the environment and human health,
which could otherwise be caused by
inappropriate waste handling of this
product.
The symbol
or on the accompanying
documentation indicates
that it should not be treated
as domestic waste but must
be taken to an appropriate
collection center for the
recycling of electrical and
electronic equipment.
on the product
DECLARATION
OF CONFORMITY
Whirlpool Europe S.r.l. - Socio
Unico, hereby declares that this
Wi-Fi enabled home appliance is
in compliance with the essential
requirements and other relevant
provisions of Directive 1999/5/EC of
9 March 1999 on radio equipment
and telecommunications terminal
equipment and the mutual
recognition of their conformity (the
R&TTE Directive).
A copy of the full original
declaration of conformity with the
R&TTE Directive can be obtained
contacting the After-sales Service
(see warranty for contacts).
7
The following statements refer to the
portions of this software based in part on
FreeRTOS v7.0.2, http://www.freertos.org.
The use of this software is governed by the
terms of GNU General Public License v. 2,
which is available at: http://www.gnu.org/
licenses/gpl-2.0.html. A copy of the source
code may be obtained by written request
for the software by name to opensource@
whirlpool.com, along with the address for
delivery.
The following statements refer to those
portions of the software copyrighted by
Eclipse Foundation, Inc.
Copyright (c) 2007, Eclipse Foundation, Inc.
and its licensors.
All rights reserved.
Redistribution and use in source and binary
forms, with or without modication, are
permitted provided that the following
conditions are met:
• Redistributions of source code must retain
the above copyright notice, this list of
conditions and the following disclaimer.
• Redistributions in binary form must
reproduce the above copyright notice,
this list of conditions and the following
disclaimer in the documentation and/
or other materials provided with the
distribution.
• Neither the name of the Eclipse
Foundation, Inc. nor the names of its
contributors may be used to endorse
or promote products derived from this
software without specic prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDERS AND CONTRIBUTORS
“AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT
OWNER OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY
OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING
IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Portions of this software are copyright (c)
Sawtooth Consulting Ltd. 2006-2015 All
rights reserved.
Portions of this software are copyright (c)
Arrayent, Inc. 2015 All rights reserved.
The following statements refer to those
portions of the software copyrighted by
Swedish Institute of Computer Science.
Copyright (c) 2001-2004 Swedish Institute of
Computer Science.
All rights reserved.
Redistribution and use in source and binary
forms, with or without modication, are
permitted provided that the following
conditions are met:
1. Redistributions of source code must
retain the above copyright notice, this list of
conditions and the following disclaimer.
2. Redistributions in binary form must
reproduce the above copyright notice,
this list of conditions and the following
disclaimer in the documentation and/
or other materials provided with the
distribution.
3. The name of the author may not be used
to endorse or promote products derived
from this software without specic prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE
AUTHOR “AS IS”’ AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE AUTHOR BE
LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
The following statements refer to those
portions of the software copyrighted by
Marvell International Ltd.
Copyright (c) Marvell International Ltd.
All rights reserved.
DISCLAIMER. THIS SOFTWARE IS PROVIDED
BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE
COPYRIGHT OWNER OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
8
Use and Care guide
PRODUCT
DESCRIPTION
APPLIANCE
EN
1.
2.
7.
1. Worktop
3.
2. Detergent dispenser
3. Control panel
4. Door handle
5. Door
4.
6. Water filter / Emergency drain hose (if available)
- behind plinth -
7. Plinth (removable)
8. Adjustable feet (4)
5.
6.
8.
9
DETERGENT DISPENSER
AutomAticdosing:
imPoRtAnt: Only use liquid detergent to ll the
detergent tanks (“1” and “2”); never use powder
detergent.
• Liquid detergent (generic or specic detergent
such as colour, wool or sport detergent)
Maximum lling quantity: 400ml.
Choose your preferred conguration among those
mentioned in section AUTO DOSING - FIRST USE in
the USE AND CARE GUIDE. The labels on the tank
aps can be turned or exchanged to remind you
the chosen conguration.
1
2
Softener
3
1
2
Softener
mAnuAl dosing:
3. Detergent compartment for manual
dosing
• Powder or liquid detergent
• Additives
If you use powder detergent, make sure to ll the
compartment only up to the “max” mark.
4. Release button
Press down to remove the detergent dispenser for
cleaning.
deteRgentRecommendAtions
foRvARioustyPesoflAundRy
Type of laundryTemperature range Recommended type of detergent
White robust laundry(cold-95°C)Heavy duty detergents
White delicate laundry(cold-40°C)
Light/pastel- shaded colours(cold-60°C)
Intensive colours(cold-60°C)
Black/dark colours(cold-60°C)Special detergents for black/dark laundry
* Find water softener appropriate for your washing
machine under www.bauknecht.eu.
Colour detergents without whitener / optical
brighteners
10
CONTROL PANEL
EN
17.
1.
2.8.3.9.4.5.6.10.11.
7.
1. On/Off button
(Reset/Drain if pressed and held down)
2. Settings button
3. Auto dosing / Tank 1
4. Auto dosing / Tank 2
5. Remote control button
6. Sensing indicator
7. Finish in button
8. Temperature button
9. Spin Speed button
10. Options button
(Key lock if pressed and held down)
11. Start / Pause button
12. OK key (to confirm)
13. UP key
14. DOWN key
15. Display
16. Option indicators
17. Programme keys
16.15.
12.
13.
14.
TECHNICAL DATA FOR WATER
CONNECTION
WATER CONNECTION
WATER SUPPLYCold
WATER TAP3/4” threaded hose connector
MINIMUM WATER SUPPLY PRESSURE100 kPa (1 bar)
MAXIMUM WATER SUPPLY PRESSURE1000 kPa (10 bar)
11
DOOR
To open the door, pull the handle
DRUM LIGHT (if available)
• During programme selection: the light goes on
for laundry loading.
• After programme start, the light fades on and o
while the laundry load is detected.
To close the door, hold the handle and push so that
you can hear it click shut.
• After programme end, when you open the door,
the light goes on for a while for unloading the
laundry. Then it goes o to save energy; touch
any button to switch it on again.
ACCESSORIES
Contact our After-Sales Service to check if the
following accessory is available for your washing
machine (and dryer) model.
B-LIVE FEATURE
Thanks to the B-Live feature, your appliance can be
connected to the Internet.
Using the B-Live app on your smartphone / tablet,
you can:
• monitor the status of the appliance
• get informed on the programme status
• set and start a programme
• change, modify, or reset a running programme
• access additional contents.
STACKING KIT SHELF
by which your dryer can be xed on top of your
washing machine to save space and to facilitate
loading and unloading your dryer in the higher
position.
• For Android users: a smart phone running
Android 4.3 (or higher) with a 1280x720 screen
resolution (or higher).
• For iOS users: a smart phone or a tablet running
iOS8 (or higher).
In order to use this feature you need to download
and install the B-Live app on your external device,
register your washing mashine using the application and connect it to your home wireless network.
Technical requirements:
• A wireless router 2.4Ghz WiFi b/g/n connected to
the Internet. Please note that the appliance has
to be installed in a place well covered by your
wireless network (good signal strength).
12
Find detailed information on how to use the B-Live
feature in the "B-Live Feature / Setup procedure"
section or in the B-Live app.
HOW TO USE
THE APPLIANCE
FIRST TIME USE
EN
If you plug in the washing machine, it will switch on
automatically. You will be asked to set the desired
language for the display.
Press the UP or DOWN key to select the desired
language, and conrm by pressing the OK key.
Afterwards you can adapt the water hardness
setting of your washing machine to your regional
water hardness. This is recommended in order
to optimize the Auto dosing function. Choose
between soft / medium / hard and conrm by
pressing the OK key.
Finally determine if you want to use Tank2 of the
Auto dosing system for softener or detergent (refer
to sections AUTO DOSING).
All settings which you do during the initial set-up
can be changed again later, if needed.
To remove any residues from the manufacturing
process:
1. Select programme “Cotton” with temperature
95°C.
AUTO DOSING FUNCTION
The detergent dispenser of the washing machine is
equipped with a two tanks system for the automatic
dispensing of liquid detergent and softener.
Before using this function, follow the instructions
in the USE AND CARE GUIDE/AUTO DOSING – FIRST
USE to:
1. Set the correct water hardness level
2. Set tank 2 content. By default, Tank
detergent (your main detergent), and Tank2 is set
for fabric softener. If you do not use fabric softener,
set Tank2 for another detergent.
3. Check/adjust the preset dosing quantities.
By default, the system comes with the following
dosing values:
• 80
ml detergent for Tank1
• 30ml softener for Tank2
You need to adjust these preset dosing values to
the dosing values reported on the detergent and
softener package that you intend to use.
After the Auto Dosing function is set for use, ll the
tanks with the appropriate content and install the
labels on the tanks accordingly, as explained in the
USE AND CARE GUIDE / AUTO DOSING – FIRST USE.
1 is set for a
2. Add a small amount of detergent to the
manual dosing compartment of the detergent
dispenser (maximum 1/3 of the quantity the
detergent manufacturer recommends for lightly
soiled laundry).
Deactivate the buttons for Auto dosing (Tank1 and
Tank2): press them so that the button light goes
o.
3. Start the programme without adding any
laundry.
See section “DAILY USE” for more information on
how to select and start a programme.
13
DAILY USE
SORTING YOUR LAUNDRY
1. REMOVE ALL OBJECTS FROM
POCKETS
• Coins, pins etc. can damage your
laundry as well as parts of the
washing machine.
• Objects like paper handkerchiefs will tear into
small pieces which must be removed manually
after the wash.
2. CLOSE ZIP FASTENERS,
BUTTONS OR HOOKS. TIE
LOOSE BELTS OR RIBBONS
TOGETHER.
• Wash small items (e.g. nylon stockings, belts etc.)
and items with hooks (e.g. bras) in a laundry bag
or pillow case with zip fastener. Always remove
curtain rings, or wash curtains with the rings
safely tied inside a cotton bag.
3. SORT ACCORDING TO TYPE O TYPE OF
FABRIC / CARE LABEL SYMBOL
Cottons, mixed bres, easy care / synthetics, wool,
handwash items.
• Colour
Separate coloured and white items. Wash new
coloured articles separately.
• Size
Wash items of dierent sizes in the same
wash load, to improve washing eciency and
distribution of the articles in the drum.
• Delicates
Wash delicate items separately; they require
gentle treatment.
14
HOW TO USE THE WASHING MACHINE
EN
1.LOAD LAUNDRY
• Open the door and load the laundry.
Load the articles one at a time loosely
into the drum, without overlling. Observe the
load sizes given in the programme chart.
Overloading the machine will result in
unsatisfactory washing results and creased
laundry.
2.CLOSE DOOR
• Make sure that no laundry gets
stuck between door glass and
rubber seal.
• Close the door so that you can hear it click shut.
3. OPEN WATER TAP
• Make sure that the washing machine is
connected to the mains.
• Open the water tap.
4.SWITCH ON WASHING MACHINE
• Press the On/O button. An animation
appears, and there is a sound. When the
display indicates a programme, the washing
machine is ready to be operated.
• The programme setting which you used last
appears on the control panel.
Change spin speed, if needed
Press the Spin button; the display indicates
that the spin speed can be set.
• Press the Spin button repeatedly
• or press the UP or DOWN key
until the desired spin speed, or Rinse hold, appears
on the display.
If you select spin speed “0”, the programme ends
with draining the rinse water. No nal spin cycle
will be applied.
If you select “Rinse hold”, the programme will
stop after the rinse phase. The laundry will
remain immerged in the last rinse water. See
more information in section PROGRAMMES AND
OPTIONS / Rinse hold.
Select options, if needed
Press the options button. The options which
are selectable for the programme appear on
the display.
• Press the UP or DOWN key to navigate through
the list of options.
5. SET THE DESIRED PROGRAMME
Select programme
Press the programme symbol on the control panel.
Programme name, default duration, temperature
and spin speed as well as maximum laundry load
appear on the display.
Find more information regarding programmes in
section PROGRAMMES AND OPTIONS and in the
Daily Reference Guide.
Change temperature, if needed
Press the temperature button; the display
indicates that the temperature can be set.
• Press the temperature button repeatedly,
• or press the UP or DOWN key until the desired
temperature appears on the display.
• Press the OK key to select an option; the option
symbol lights up on the control panel.
Options may not be combinable with each other.
When selecting an option, the non-combinable
option will be deactivated automatically if this is
the case.
Some options / functions can be selected by
directly pressing the button:
12
If such an option is not selectable for the
programme, it switches o automatically when the
button is pressed.
Refer to section PROGRAMMES AND OPTIONS for
more information.
15
6. ADD DETERGENT
• If you want to add the detergent
manually, pull out the detergent
dispenser and add detergent (and additives) now,
as indicated in section DETERGENT DISPENSER.
Observe the dosing recommendations on the
detergent pack. If you have selected PREWASH
or FINISH IN, observe the instructions in section
PROGRAMMES AND OPTIONS, and FUNCTIONS.
Afterwards carefully close the detergent
dispenser.
• If you want the washing machine to dose the
detergent automatically, simply make sure the
Auto Dosing function is activated (refer to section
OPTIONS, FUNCTIONS AND INDICATORS / Auto
dosing). The detergent is added by the Auto
dosing system after programme start.
To assure correct dosage, make sure that the Auto
dosing system is adapted to your detergents /
softener (refer to AUTO DOSING / AILY USE).
Correct dosing of detergent / additives is
important, because
• it optimizes the cleaning result
• it avoids irritating residues of surplus detergent in
your laundry
• it saves money by avoiding waste of surplus
detergent
• it protects the washing machine by avoiding
calcication of components
• it respects the environment by avoiding
unnecessary environmental burden
Refer to section Troubleshooting for more
information on unbalance in the laundry load.
8. CHANGE THE SETTINGS OF A RUNNING
PROGRAMME, IF NEEDED
You can still change the settings while a
programme is running. The changes will be
applied, provided the respective programme phase
has not nished yet. If the change is not possible,
there will be an error sound when pressing the
button.
• To change temperature or spin
speed:
Press the Temperature or Spin
speed button; the display indicates that
temperature or spin speed can be set. Press
the button repeatedly, until the desired
value appears on the display. Or select the
desired value by pressing the UP or DOWN
key.
• To add or remove an option:
Press the Options button; the display
indicates the options which are selectable
for the programme. Press the OK key to
select or deselect an option.
For options directly selectable by a button,
press the button to select or deselect the option.
12
7. START PROGRAMME
• Press and hold “Start/Pause” until the
button lights up solidly; the programme
starts.
• The drum turns, and the load is detected. The
display indicates the load sensing, while on the
control panel an animation occurs.
• The remaining programme duration which is
indicated on the display can vary. Factors like
unbalance in the wash load, or foam formation,
can have an eect on the programme duration.
Whenever the remaining programme duration
is calculated newly, the display indicates the
sensing, and an animation occurs on the control
panel.
• If the washing machine detects an unbalance
in the laundry load, the washing machine
automatically tries to create a balance. The
display indicates the load balancing.
16
• To change the “Finish in” delay:
Press the Finish in button; the selected
delay blinks on the display. While blinking,
the value can be changed by pressing the
UP or DOWN key.
The programme proceeds automatically after the
setting has been changed. To prevent that a
running programme is changed by accident (for
instance by children), use the “Key lock” (see
section FUNCTIONS).
To change the settings of a running programme,
you can also
• Press “Start/Pause” to put the running
programme on pause
EN
• Change your settings
• Press “Start/Pause” again to continue the
programme.
If you have changed the programme, do not add
detergent for the new programme.
9. PAUSE A RUNNING PROGRAMME AND
OPEN THE DOOR, IF NEEDED
After programme start, the display indicates when
the programme can still be paused to add
garments.
• Press and hold “Start/Pause” to pause a
running programme
• Provided water level or temperature is not
too high, the “door open” indicator lights
up. You can open the door, for example
to add more laundry, or to remove laundry
which was loaded by mistake.
• Press “Start/Pause” to proceed with the
programme
10. RESET A RUNNING PROGRAMME, IF
NEEDED
• Press and hold the “On/O” button until
the display indicates that the programme
is cancelled. The water drains. The
programme is ended, and the door unlocks.
11. SWITCH OFF THE WASHING MACHINE
AFTER PROGRAMME END
• The display indicates that the cycle is
nished, and the “Door open” indicator
lights up – you can take out your laundry.
• Press “On/O” to switch o the washing
machine. If you do not switch it o,
the washing machine will switch o
automatically about a quarter of an hour after
programme end, to save energy.
• Leave the door ajar, so that the inside of the
washing machine can dry.
17
PROGRAMMES
AND OPTIONS
For choosing the appropriate programme for your
kind of laundry, always respect the instructions on the
care labels of the laundry.
PROGRAMMEType of Wash
and Recommendations
ECO COTTON
Normally soiled cotton laundry.
At 40 °C and 60 °C standard cotton
programme and most favourable
programme in terms of combined
water and energy consumption. Basis
for the values indicated on the Energy
Label.
COTTON
Normally to heavily soiled robust
laundry made of cotton and linen, such
as towels, underwear, table, bed linen
etc.
MIXED
Lightly to normally soiled robust
laundry made of cotton, linen, articial
bres and their blends.
Eective one-hour programme. Only
wash similar colours together in one
wash load.
SYNTHETICS
Normally soiled laundry made
of articial bres (like polyester,
polyacrylics, viscose etc.) or their
blends with cotton.
DELICATES
Fine laundry made of delicate fabrics,
which needs gentle treatment.
Care
Labels
Settings
max. load max
temperaturerange
Cold to 60°C
maxspinspeed max
selectableoptions Intensive
Rinse, Rapid, Colours 15°,
Fresh Care
max. load max
temperaturerange
Cold to 95°C
maxspinspeed max
selectableoptions Prewash,
Hot nish, Bio Stain 15°,
Heavy soil, Intensive rinse,
Rapid, Colours 15°, Fresh
care
max. load 7.0 kg
temperaturerange
Cold to 60°C
maxspinspeed max
selectableoptions Hot Finish,
Bio Stain 15, Intensive
Rinse, Rapid, Colours 15°,
Fresh Care
max. load 4.0 kg
temperaturerange
Cold to 60°C
maxspinspeed max
selectableoptions Prewash,
Bio Stain 15, Heavy Soil,
Intensive Rinse, Rapid,
Colours 15°, Fresh Care
max. load 3.0 kg
temperaturerange
Cold to 40°C
maxspinspeed 1000
selectableoptions Prewash,
Rapid, Colours 15°, Fresh
Care
18
EN
PROGRAMMEType of Wash
and Recommendations
WOOL
Woolens, labeled with the Woolmark
and identied as machine washable, as
well as textiles made of silk, linen, wool
and viscose marked as handwashable.
Respect the manufacturers
recommendations on the care label.
RAPID 30’
Lightly soiled laundry without stains,
made of cotton and/or synthetics.
30’
Refresh programme.
COLOURS
Lightly to normally soiled laundry
made of cotton, synthetics or their
blends; also delicates.
Helps preserving the colours of your
laundry. Take care to use detergent
which is appropriate for the colours of
your laundry load.
SPIN
Separate intensive spin programme.
Suitable for robust laundry.
RINSE&SPIN
Separate rinse and intensive spin
programme. Suitable for robust
laundry.
DRAIN
Separate programme to drain the
water, without spinning. Can be
selected if your laundry is in Rinse
hold, and you want to drain the water
without spinning the wet laundry. As
an alternative to the Drain programme,
you can select spin speed “0” to
terminate the Rinse hold without
spinning. Appropriate for delicate
laundry like ne garments or curtains.
Care
Labels
Settings
max. load 2.0 kg
temperaturerange
Cold to 40°C
maxspinspeed 1000
selectableoptions Rapid,
Colours 15°, Fresh Care
max. load 3.0 kg
temperaturerange
Cold to 30°C
maxspinspeed max
selectableoptions Colours 15°,
Fresh Care
max. load 7.0 kg
temperaturerange
Cold to 60°C
maxspinspeed 1000
selectableoptions Prewash,
Bio Stain 15, Heavy Soil,
Rapid, Colours 15°, Fresh
Care
max. load max
temperaturerange Cold
maxspinspeed max
selectableoptions Fresh Care
max. load max
temperaturerange Cold
maxspinspeed max
selectableoptions Intensive
Rinse, Fresh Care
19
PROGRAMMEType of Wash
and Recommendations
Care
Labels
Settings
SPECIAL
PROGRAMMES
To set one of the following
programmes, select the special
programmes position. Press the DOWN
and UP keys to select one of the
programmes mentioned below.
The selected programme is marked
with “ > “.
Press the OK key to conrm the
selected programme.
SHIRTSShirts, blouses and ne business
clothes made of cotton, synthetics or
their blends.
Provides gentle treatment for ne
garments.
DUVETBig items such as sleeping bags,
washable blankets, bathmats, pillows
and duvets lled with feathers or
synthetic material.
Adapted to wash and spin big laundry
items.
Respect the manufacturer’s
recommendations on the care label of
the laundry
BED LINENWhite or coloured bed linen made of
cotton and synthetic bers, or blends
of both.
Reduces microbes and gently cleans,
also delicate bed linen. A thorough
rinse phase helps to prevent detergent
and pollen residues.
CASHMEREHigh-quality cashmere garments
identied as machine washable or
hand washable.
Use liquid detergent for woolen
laundry. Respect the manufacturer’s
recommendations on the care label of
the laundry.
max. load 3.0 kg
temperaturerange
Cold to 40°C
maxspinspeed 1000 rpm
selectableoptions Prewash,
Colours 15°, Rapid, Fresh
Care
max. load 3.5 kg
temperaturerange
Cold to 60°C
maxspinspeed 1000 rpm
selectableoptions
Prewash,BioStain 15,
Intensive rinse, Hot nish,
Colours 15°, Rapid, Fresh
Care
max. load 3.5 kg
temperaturerange
Cold to 95°C
maxspinspeed max
selectableoptions Prewash,
BioStain 15, Intensive
Rinse, Hot nish, Colours
15°, Rapid, Fresh Care