YOUR SAFETY AND SAFETY
OF OTHERS IS VERY IMPORTANT.
This manual and the appliance
itself provide important safety
warnings, to be read and
observed at all times.
This is the safety alert symbol.
This symbol alerts you to
potential hazards that can kill
or hurt you and others.
All safety messages will follow
the safety alert symbol and
either the word DANGER or
WARNING. These words mean:
DANGER
Indicates a hazardous situation
which, if not avoided, will
cause serious injury.
WARNING
Indicates a hazardous situation
which, if not avoided, could
cause serious injury.
All safety warnings give specic details of the potential risk
presented and indicate how to
reduce risk of injury, damage
and electric shock resulting
from improper use of the
appliance. Carefully observe
the following instructions.
Failure to observe these instructions may lead to risks.
The manufacturer cannot be
held liable for any damage
resulting from failure to respect this guide.
The Manufacturer declines any
liability for injury to persons or
animals or damage to property
if the above advice and precautions are not respected.
Keep these instructions close
at hand for future reference.
Do not store explosive substances such as aerosol cans
and do not place or use gasoline or other ammable materials in or near the appliance.
When scrapping the appliance,
make it unusable by cutting o
the power cable and removing
the doors and shelves (if present) so that children cannot
easily climb inside and become
trapped.
This appliance does not contain CFCs. The refrigerant
circuit contains R600a (HC).
Appliances with Isobutane
(R600a): isobutane is a natural
gas without environmental
impact, but is ammable.
Therefore, make sure the
refrigerant circuit pipes are not
damaged. Keep special attention in case of damaged pipes
emptying the refrigerant
circuit.
C-Pentane is used as blowing
agent in the insulation foam
and it is a ammable gas.
WARNING
Do not damage the appliance
refrigerant circuit pipes.
WARNING
Do not use mechanical, electric
or chemical means other than
those recommended by the
Manufacturer to speed up the
defrost process.
WARNING
Do not use or place electrical
devices inside the appliance
compartments if they are not
of the type expressly authorised by the Manufacturer.
WARNING
Ice makers and or water dispencers not directly connected
to the water supply must be
lled with potable water only.
4
EN
WARNING
Keep ventilation openings, in
the appliance enclosure or in
the built-in structure, clear of
obstruction.
WARNING
Automatic ice-makers and/or
water dispensers must be
connected to a water supply
that delivers potable water
only, with main water pressure
between 0,17 and 0,81 MPa (1,7
and 8,1 bar).
To guarantee adequate ventilation, leave a space on both
sides and above the appliance.
The distance between the rear
of the appliance and the wall
behind the appliance should
be at least 50mm.
A reduction of this space will
increase the Energy consumption of product.
INTENDED USE
OF THE PRODUCT
This appliance is designed
solely for use as domestic
usage. To aim the appliance as
professional use is forbidden.
The manufacturer declines
allresponsibility for innapropiate use or incorrect setting of
the controls.
The appliance is not intended
to be operated by means of an
external timer or separate
remote control system.
Do not use the appliance
outdoors.
This appliance is intended to
be used in household and
similar
applications such as:
– sta kitchen areas in shops,
oces and other working
environments;
– farm houses and by clients in
hotels, motels and other residential type environments;
– bed and breakfast type
environments;
– catering and similar nonretail applications.
The bulb used inside the appliance is specically designed for
domestic appliances and is not
suitable for general room
lighting within the home (EC
Regulation 244/2009).
INSTALLATION
Only activate the appliance
when the installation procedure has been completed.
Installation and repairs must
be carried out by a qualied
technician, in compliance with
the manufacturer’s instructions
and local safety regulations. Do
not repair or replace any part
of the appliance unless specically stated in the user manual.
Use protective gloves to perform all unpacking and installation operations.
The appliance must be disconnected from the power supply
before carrying out any installation operation.
After unpacking the appliance,
make sure that it has not been
damaged during transport. In
the event of problems, contact
the dealer or your nearest
After-sales Service.
During installation, make sure
the appliance does not dam-
age the power cable.
The appliance must be handled and installed by two or
more persons.
When installing the appliance
make sure that the four feet are
stable and resting on the oor,
adjusting them as required,
and check that the appliance is
perfectly level using a spirit
level.
Wait at least two hours before
switching the appliance on, to
ensure that the refrigerant
circuit is fully ecient.
Make sure the appliance is not
near a heat source.
ELECTRICAL WARNINGS
Make sure the voltage specied on the rating plate corresponds to that of your home.
The power supply ranges are
indicated on the rating plate.
Regulation require that the
appliance is earthed.
For installation to comply with
current safety regulations, an
omnipolar switch with minimum contact gap of 3mm is
required.
If the power cable is damaged
it must be replaced with an
identical one. The power cable
must only be replaced by a
qualied technician in compliance with the manufacturer
instruction and current safety
regulations. Contact an authorized service center.
The electrical components
must not be accessible to the
user after installation.
5
The power cable must be long
enough for connecting the
appliance, once tted in its
housing, to the main power
supply.
Do not use extension leads.
Do not pull the power supply
cable.
Do not use multiple plug
adaptors if the appliance is
tted with a plug.
For appliances with tted plug,
if the plug is not suitable for
you socket outlet, contact a
qualied technician.
Do not touch the appliance
with any wet part of the body
and do not operate it when
barefoot.
ELECTRICAL CONNECTION
FOR GREAT BRITAIN AND
IRELAND ONLY
Fuse replacement.
If the mains lead of this appliance is tted with a BS 1363A
13amp fused plug, to change a
fuse in this type of plug use an
A.S.T.A. approved fuse to BS
1362 type and proceed as
follows:
Socket outlet / plug (valid for
both countries)
If the tted plug is not suitable
for your socket outlet, please
contact After-sales Service for
further instruction. Please do
not attempt to change plug
yourself. This procedure needs
to be carried out by a qualied
technician in compliance with
the manufactures instructions
and current standard safety
regulations.
CORRECT USE
Use the refrigerator compartment only for storing fresh
food and the freezer compartment only for storing frozen
food, freezing fresh food and
making ice cubes.
Do not operate this appliance
if it has a damaged mains cord
or plug, if it is not working
properly, or if it has been
damaged or dropped. Do not
immerse the mains cord or
plug in water. Keep the cord
away from hot surfaces.
When using a residual current
circuit breaker (RCCB), only use
a model marked with
.
The appliance is arranged for
operation in places where the
temperature comes within the
following ranges, according to
the climatic class given on the
rating plate.
The appliance may not work
properly if it is left for a long
time at a temperature outside
the specied range.
Climatic Class Amb. T. (°C)
SN From 10 to 32
N From 16 to 32
ST From 16 to 38
T From 16 to 43
1. Remove the fuse cover (A)
and fuse(B).
2. Fit replacement 13A fuse into
fuse cover.
3. Ret both into plug.
Important:
The fuse cover must be retted
when changing a fuse and if
the fuse cover is lost the plug
must not be used until a correct replacement is tted.
Correct replacement are identied by the colour insert or the
colour embossed in words on
the base of the plug.
Replacement fuse covers are
available from your local electrical store.
For the Republic of Ireland
only
The information given in
respect of Great Britain will
frequently apply, but a third
type of plug and socket is also
used, the 2-pin, side earth
type.
Avoid storing unwrapped food
in direct contact with internal
surfaces of the refrigerator or
freezer compartments.
Appliances could have special
compartments for food storage.
In case not dierently specied
in the specic booklet of
product, they can be removed,
maintaining equivalent performances.
Do not swallow the contents
(non-toxic) of the ice packs (in
some models).
Do not eat ice cubes or ice
lollies immediately after taking
them out of the freezer since
they may cause cold burns.
For products designed to use
an air lter inside an accessible
fan cover, the lter shall be
always in position when the
refrigerator is in function.
Do not store glass containers
6
EN
with liquids in the freezer
compartment since they may
break.
Do not obstruct the fan (if
available) with food items.
After placing the food check if
the door of compartments
closes properly, especially the
freezer door.
Damaged gasket must be
replaced as soon as possible.
CHILDREN SAFETY
Very young (0-3 years) and
young children (3-8 years) shall
be kept away unless continuously supervised.
Childern from 8 years old and
above and persons with reduced physical, sensory or
mental capabilities or lack of
experience and knowledge can
use this appliance only if they
are supervised or have been
given instructions on safe
appliance use and if they
understand the hazards involved. Children shall not play
with the appliance. Cleaning
and user maintenance shall not
be made by childern without
supervision.
Keep the packaging materials
(plastic bags, polystyrene
parts, etc.) out of reach of
children.
CLEANING
AND MAINTENANCE
The appliance must be disconnected from the power supply
before carrying out any cleaning or maintenance operation.
Never use steam cleaning
equipment
SAFEGUARDING
THE ENVIRONMENT
DISPOSAL OF PACKAGING
MATERIALS
The packaging material is
100% recyclable and is marked
with the recycle symbol:
The various parts of the
packaging must therefore be
disposed of responsibly and in
full compliance with local
authority regulations
governing waste disposal.
SCRAPPING OF
HOUSEHOLD APPLIANCES
This appliance is manufactured
with recyclable or reusable
materials. Dispose of it in
accordance with local waste
disposal regulations.
For further information on the
treatment, recovery and
recycling of household
electrical appliances, contact
your competent local
authority, the collection service
for household waste or the
store where you purchase the
appliance.
This appliance is marked in
compliance with European
Directive 2012/19/EU, Waste
Electrical and Electronic
Equipment (WEEE).
By ensuring this product is
disposed of correctly, you will
help prevent potential
negative consequences for the
environment and human
health, which could otherwise
be caused by inappropriate
waste handling of this product.
This symbol on the
product or on the
accompanying
documentation indicates that
it should not be treated as
7
domestic waste but must be
taken to an appropriate
collection centre for the
recycling of electrical and
electronic equipment.
ENERGY SAVING TIPS
Install the appliance in a dry,
well ventilated room far away
from any heat source (e.g.
radiator, cooker, etc.) and in a
place not exposed directly to
the sun. If required, use an
insulating plate.
To guarantee adequate
ventilation follow installation
instructions. Insucient
ventilation on back of the
product increases energy
consumption and decreases
cooling eciency.
The internal temperatures of
the appliance may be aected
by the ambient temperature,
frequency of door opening, as
well as location of the
appliance. Temperature setting
should take into consideration
these factors.
Reduce to a minimum door
opening.
When thawing frozen food,
place them in the refrigerator.
The low temperature of the
frozen products cools the food
in the refrigerator.
Allow warm food and drinks to
cool down before placing in
the appliance.
Positioning of the shelves in
the refrigerator has no impact
on the ecient usage of
energy. Food should be placed
on the shelves in such way to
ensure proper air circulation
(food should not touch each
other and distance between
food and rear wall should be
kept).
You can increase storage
capacity of frozen food by
removing baskets and, if
present, Stop Frost shelve,
maintaining an equivalent
energy consumption.
High energy class products are
tted with high eciency
motors that remain operational
for longer, but have a low
power consumption. Do not
worry if the engine continues
to run for longer periods.
DECLARATION
OF CONFORMITY
This appliance has been
designed for preserving food
and is manufactured in
compliance with Regulation
(CE) No . 1935/2004 .
This appliance has been
designed, manufactured and
marketed in compliance with:
› safety objectives of the “Low
Voltage” Directive 2006/95/CE
(which replaces 73/23/CEE and
subsequent amendments);
› the protection requirements
of Directive “EMC” 2004/108/
EC. Electrical safety of the
appliance can only be
guaranteed if it is correctly
connected to an approved
earthing system.
Whirlpool Europe S.r.l. - Socio
Unico, hereby declares that this
Wi-Fi enabled home appliance
is in compliance with the
essential requirements and
other relevant provisions of
Directive 1999/5/EC of 9 March
1999 on radio equipment and
telecommunications terminal
equipment and the mutual
recognition of their conformity
(the R&TTE Directive).
A copy of the full original
declaration of conformity with
the R&TTE Directive can be
obtained contacting the Aftersales Service (see warranty for
contacts).
8
EN
The following statements refer to the
portions of this software based in part on
FreeRTOS v7.0.2, http://www.freertos.org.
The use of this software is governed by the
terms of GNU General Public License v. 2,
which is available at: http://www.gnu.org/
licenses/gpl-2.0.html. A copy of the source
code may be obtained by written request
for the software by name to opensource@
whirlpool.com, along with the address for
delivery.
The following statements refer to those
portions of the software copyrighted by
Eclipse Foundation, Inc.
Copyright (c) 2007, Eclipse Foundation, Inc.
and its licensors.
All rights reserved.
Redistribution and use in source and binary
forms, with or without modication, are
permitted provided that the following
conditions are met:
• Redistributions of source code must retain
the above copyright notice, this list of
conditions and the following disclaimer.
• Redistributions in binary form must
reproduce the above copyright notice,
this list of conditions and the following
disclaimer in the documentation and/
or other materials provided with the
distribution.
• Neither the name of the Eclipse
Foundation, Inc. nor the names of its
contributors may be used to endorse
or promote products derived from this
software without specic prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDERS AND CONTRIBUTORS
“AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT
OWNER OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY
OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING
IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Portions of this software are copyright (c)
Sawtooth Consulting Ltd. 2006-2015 All
rights reserved.
Portions of this software are copyright (c)
Arrayent, Inc. 2015 All rights reserved.
The following statements refer to those
portions of the software copyrighted by
Swedish Institute of Computer Science.
Copyright (c) 2001-2004 Swedish Institute of
Computer Science.
All rights reserved.
Redistribution and use in source and binary
forms, with or without modication, are
permitted provided that the following
conditions are met:
1. Redistributions of source code must
retain the above copyright notice, this list of
conditions and the following disclaimer.
2. Redistributions in binary form must
reproduce the above copyright notice,
this list of conditions and the following
disclaimer in the documentation and/
or other materials provided with the
distribution.
3. The name of the author may not be used
to endorse or promote products derived
from this software without specic prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE
AUTHOR “AS IS”’ AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE AUTHOR BE
LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
The following statements refer to those
portions of the software copyrighted by
Marvell International Ltd.
Copyright (c) Marvell International Ltd.
All rights reserved.
DISCLAIMER. THIS SOFTWARE IS PROVIDED
BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE
COPYRIGHT OWNER OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
9
Use and Care guide
11
12
14
21
10
25
PRODUCT
DESCRIPTION
APPLIANCE
2
3
13
4
6
5
7
8
9
22
23
24
16
17
18
19
15
20
1. Control panel
Refrigerator compartment
2. LED lighting
3. Fan
4. Fan cover and antibacterial
lter area
5. Shelves
1
6. Bottle rack
7. Multi-ow cold air area
8. Cheese box + Lid
9. Sensor cover
10. Zero0 BioZone compartment
(to keep foods fresher for longer)
11. Rating plate with commercial
name
12. Fruits and vegetables crisper
13. Fridge drawer divider
14. Door reversibility kit
15. Door trays
16. Egg tray
17. Small items half balcony
18. Bottle separator
19. Bottle balcony
20. Door seal
Freezer compartment
20. Door seals
21. Freezer drawers
22. Quick Ice / Eutetic
23. Middle drawer: coolest zone
best for freezing fresh food
24. Freezer drawer divider
25. Shelves
10
CONTROL PANEL
4
1216
14
19
2311
13
20
21
22
15
18
17
2
1
3
Menu
5
EN
1. FRIDGE TEMPERATURE button/indicator
9
7
6
10
8
2. FRIDGE TEMPERATURE DISPLAY (°C)
3. VACATION MODE indicator
4. TEXT DISPL AY
5. FREEZE CONTROL indicator
6. FREEZER TEMPERATURE DISPLAY (°C)
7. FREEZER TEMPERATURE button
8. ANTIBACTERIAL AIR FILTER alarm indicator
9. BLACK-OUT ALARM indicator
10. MALFUNCTION ALARM indicator
11. ON/STAND-BY button/indicator
12. FAST COOL button/indicator
13. ZERO0 BIOZONE button/indicator
14. NIGHT TARIFF indicator
15. MENU button (to access additional
function as: Language, Party Mode, Vacation,
Smart display, Freeze control, Night tari,
Live)
16. PRO FRESH CONTROL indicator
17. CONNECTION STATE indicator
18. 0K button
19. PARTY MODE indicator
20. KEY LOCK button/indicator
21. FAST FREEZE button/indicator
22. STOP ALARM button/indicator
23. DOOR OPEN ALARM indicator
This control panel has an innovative technology that will drive you are setting your fridge. When un option
or a function is activated the indicator is fully lit on; when a option is available but not selected is partially
lit on.
NOTE: when you are setting temperature or interacting with the control panel, all the buttons are switched
on. when you are not using the control panel, in order to save energy it will show you only the relevant
information (the temperature set, the activated options).
Every time you want to use the control panel and see all the functions, you just need to touch any button
to wake up the panel.
11
TECHNICAL
DATA
PRODUCT DIMENSIONS
Height 1885mm
Width595mm
Depth655mm
NET VOLUME FRIDGE L 186L
NET VOLUME CHILL COMPARTMENT L16L
NET VOLUME FREEZER L 94L
DEFROST SYSTEM
FridgeAutomatic
FreezerAutomatic
RISING TIME H22h
FREEZING CAPACITY KG/24H15. 5Kg/24h
ENERGY CONSUMPTION KWH/24H0.46Kwh/24h
NOISE LEVEL DBA39dba
ENERGY CLASSA+++
12
DOOR
DOOR REVERSIBILITY Note: The direction of door opening can be
changed. If this operation is performed by Aftersales Service it is not covered by the warranty.
Is recommended to reverse door swing by two
persons.
Follow instruction in Installation Guide.
REFRIGERATOR LIGHT
EN
The light system inside the fridge compartment
uses LEDs light, allowing a better lightning as well
as very low energy consumption.
If the LED light system does not work, please
contact the Service to replace it.
Important: The refrigerator compartment light
switches on when the refrigerator door is opened. If
the door is kept open for more than 10 minutes the
light will be automatically switched o.
SHELVES
All shelves, aps and pull-out baskets are
removable.
FAN + ANTIBACTERIAL AIR FILTER
The Fan improves temperature distribution inside
the product, allowing better preservation of stored
food.
Note: Do not obstruct the air intake area with food
items.
If the appliance has the Fan it can be equipped with
the antibacterial lter.
Remove it from the box placed in the crisper drawer
and insert into the fan cover - as in the picture.
The replacement procedure is included in the lter
box.
The air lter symbol is lit on to
indicates that it is expired and
need to be replaced. The lter
expires in 6 months. The User
Interface gives a visual feedback,
without acoustic alarm. On text
display show message “Replace air
lter ”.
After replaced the lter, press Stop Alarm button to
reset message on the text display/antibacterial air
lter indicator.
NO-FROST REFRIGERATOR
COMPARTMENT
Refrigerator compartment defrosting is completely
automatic.
The defrost water is automatically run into a drain
hole hiden behind Multi-ow and collected in a
container, where it evaporates.
13
NO-FROST FREEZER
COMPARTMENT
No Frost freezers provide chilled air circulation
around the storage areas, and prevent the
formation of ice, thereby completely eliminating
the need for defrosting.
Frozen items don’t stick to the walls, labeling stays
legible and storage space remains neat and clear.
After plugging in the appliance to the mains, press
the On/Standby button to switch on. When
switched on for the rst time, the display will guide
you to basic conguration (Set Language): a
message in dierent languages is displayed in loop;
Use the Menu button to scroll the list of languages
and conrm the language by pressing OK button.
CONNECTIVITY PRE-REQUISITE
When the refrigerator is connected to
Internet,You can always monitor and operate
remotely the appliance.
To use this feature You need to own:
- a smart phone running Android 4.3 (or higher)
with a 1280x720 (or higher) screen or a tablet or
a smart phone running iOS 8 (or higher);
- a wireless router 2.4Ghz WiFi b/g/n connected
to internet (verify with your smart device that
the signal strength of your home wireless
network close to the appliance is good).
Important in order to use App, You have to :
- Check if the room in which your smart
After set language, the control panel will be turned
on default status. The default value settings are
displayed for refrigerator (5 °C) and for Freezer
compartment (-18°C).
After starting the appliance, wait at least 4-6 hours
before placing food into the appliance.
The default (factory) values of the fridge
compartment settings light-up.
appliance is installed is covered by the signal of your
home wireless network.
- Own a IOS device (Ipad/Iphone) or Android
(Smartphone)
– Download the free “Live” app from the reference
App store or Google play of your smart device and
install it on your device.
– Subscribe (legal terms) to the service to be able to
benet of the features provided through the app.
– Register your refrigerator and connect it to your
home wireless network.
Find detailed information on connectivity setup in
the App.
TEMPERATURE SETTING
FRIDGE TEMPERATURE
To adjust the Fridge Temperature, press the Fridge °C
button
adjusted between +2°C and + 8°C, as shown by the
Fridge Temperature Display (°C).
. The Fridge Temperature can be
FREEZER TEMPERATURE
To adjust the Freezer Temperature, press the Freezer
°C button . The Freezer Temperature can be
adjusted between -16°C and -24°C, as shown by the
Freezer Temperature Display (°C).
15
Loading...
+ 34 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.