Bauknecht GSI 5599/1 G IX, GSI 5599/1 G WS, GSI 5599/1 G SW Quick Reference Guide

4GB96016.fm Page 1 Wednesday, September 15, 2004 5:16 PM

Before using the dishwasher, read the user instructions!

GCI 5599 G IX

Programme ON/OFF selector knob

First press and release the selector knob to access it,
and then turn it to select the desired programme;
the dishwasher switches on.
To switch off the dishwasher when the programme
has finished, turn the selector knob to off.

Start button

Press to start the wash cycle and keep pressed until
an acoustic signal confirms the start of the wash
cycle. The display shows the approximate duration
of the wash cycle.

the light above the start button blinks during

Note:

the wash cycle.
The light stops blinking and remains alight to indicate
the cycle has ended (“End” on the display) or has

been interrupted due to a fault (“E1, E2....” on the

display).

Indicators

Add rinse aid

Add regeneration salt

Only add regeneration salt immediately before

starting a wash programme.

Quick Reference Guide

Options

Antebacterial rinse (Sani-Rinse option)

This function executes an antibacterial rinse at the
end of the wash cycle, thereby further reducing
bacteria levels. The lamp will light up when the
function is activated. If the temperature is not
maintained during the antibacterial cycle
(e.g. if the door is opened or a power failure
occurs), the lamps will start blinking to indicate
that the antibacterial action is not guaranteed.

Half load function

Recommended when the dishwasher is not full to
save water and electricity. Press the button to
wash the top rack. Press the button to wash the
bottom rack. Press the button again to deactivate
the function. The indicator light and display show
that only one rack is selected.

WARNING:

switched off.

“Delayed start” button

The wash cycle can be programmed to start after
1-12 hours. Then press the Start button. After a
prewash the set delay will start.

Display

The display shows all the information relating to
the selected functions and the indication about all
functional failures (see table on the “Instructions
for Use” manual).

GB

This function remains selected until

Programme chart

Programmes Loading instructions

P1
P2

P3

P4

P5

1) Reference programme for energy label in compliance with
EN 50242;

Black process 45.0° 100.0 LPI

Pre-Rinse cold

Rapid 30 min 45°C

Eco

1)

55°C

Normal 65°C

Intensive 70°C

Detergent

A B Litres kWh Minutes

Crockery to be washed later. - - 6.0 0.02 15

Lightly soiled crockery with no dried-on
food.

Normally soiled crockery. X - 14.0 1.05 180

Normally or heavily soiled crockery. X - 17.0 1.28 90

Recommended programme for heavily
soiled crockery, especially suitable for pans
and saucepans.

2) Programme data obtained in conformity with European standard
EN 50242. Values may vary in relation to usage, e.g.: different loads,
water temperatures - above or below 15° C - as well as water
hardness and power supply voltage, etc.

X - 13.0 0.80 45

X X 20.0 1.60 110

Consumption

2)

5019 496 96016

(We reserve the right to make technical modifications)

D

4GB96016.fm Page 2 Wednesday, September 15, 2004 5:16 PM

How to use the appliance

Further indications are given in the single chapters and in the user instructions.

Open the door

How to fill the

detergent dispenser

Check the rinse aid level

Check the

regeneration salt level

Load the racks

Close the door,

select a programme

Select

additional options

Turn on the water tap

Press the Start button

to start the programme

(during the cycle the

Start indicator blinks)

Wash cycle

Large compartment

A

C

AB

Small compartment

Mechanical indicator lamp C.
Electric indicator on control panel (if provided).

On models with water softener system
only.

Mechanical indicator lamp D.
Electric indicator on control panel
(if provided).

Refer to the dishwasher loading instructions.

Press and turn the selector knob to select the desired programme and
switch on the appliance.

If necessary (and if provided).
The corresponding indicator lamp lights up.

“Cancel”

Press and hold the “Start” button

until the indicator lamp stops
blinking and stays on.

Press and hold the “Start” button

for 10 seconds. “P0” will appear on
the display and the programme will
stop.

B

“Change programme in
progress”

Press and hold the “Start” button
until the indicator lamp stops blinking
and stays on.

Select and start the programme as

described previously.

- Only open the dishwasher if
necessary (Warning: beware of
hot steam).

- If the appliance is switched off
during a wash cycle, when
switched on again it will resume
the cycle from where it was
interrupted.

Black process 45.0° 100.0 LPI

Switch off the appliance

Turn off the water

tap, unload the racks

To switch off the dishwasher turn the selector knob to off.
All the indicator lamps and the display switch off.

Warning: When the door is opened steam comes out!

Unload the appliance, starting from the lower rack.