Bauknecht GSI 5570/1 WS, GSI 5570/1 SW, GSI 5570/1 IN INSTALLATION
Before using the dishwasher, read the
installation and maintenance instructions carefully!
GSI 5570
GB
1. OVERVIEW
Programme selector
START button
Switches “on” when the dishwasher is operating. Flashes when a
fault occurs. Switches off at the end of the programme.
START button RESET fun ctio n:
Press this button for at least 2 seconds; the selected programme
and options are cancelled. Main failure displays (repeated flashing
of the START indicator lamp) can be cancelled by RESETTING.
Detailed instructions are given in chapter 5 “What to do if...”.
Rinse aid level indicator and salt level indicator
They light up when rinse aid or salt need to be added.
Add just before starting a wash cycle.
Fault indication and wash time display
With normal operation, the display indicates residual time (h:mm),
while with the “Delayed start” function selected it indicates time
remaining until the start of the programme (hh).
Detergent setting upon initial use and when using a different type of detergent
1. Select the third programme in the relative table.
2. Press the START button for approx. 7 sec. to change the display.
3. Using the START button, select the desired detergent:
4. Switch the appliance off and then switch it on again. The selected detergent
If “F..” appears on the display, see chapter 5 “What to do if.. .”.
Display shows: 2 -1 = 2 in 1, 3 -1 = 3 in 1, 4 -1 = other combined action
detergents (in this way, the rinse aid and/or salt indicator is deactivated).
Display shows OFF = Powder detergent (factory setting).
(rinse aid level and salt level indicator activated).
type will be indicated on the display for approx. 3 seconds.
Table 1.1.
“Delayed start” button
Press the button as required to delay the start of the programme.
Adjustable from 1 to 24 hours. With each press of the button, the
delayed start indicator increases by one hour and after 24 restarts
from 00. Then press the START button. The dishwasher will start
after the set time.
Half Load / Multizone Button”
The half load cycle can be used for the upper or lower rack. Select
the required programme then press the “Half load” button. The
light comes on and goes off at the end of the programme.
This function can be used with the programmes indicated in table 1.1.
Antibacterial rinse
This function activates an antibacterial rinse at the end of the wash
cycle, guaranteeing a further reduction of bacteria. Press the button to
activate or deactivate the function. This function can be used with
those programmes marked with the relative symbol in table 1.1.
The dishwasher door must be kept shut for the entire duration of
the programme in order to guarantee reduction of bacteria. If the
door is opened the indicator lamp starts flashing.
On / Off Button
3)
Table of programmes
P
1
2
3
4
5
1) Program data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g. different loads,
options, different sensor settings (only with sensor programmes), different water supply temperatures, as well as water hardness
and power supply voltage.
2) Energy label programme in compliance with EN 50242. - Information for Test Laboratories:
the EN comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been shown in collaboration with the Pasteur Institute, Lille (France), in conformity with.
Standard NF EN 13697 - November 2001.
Programmes
Pre-Rinse cold
Quickwash 40°C
Bio
2)
50°C
Daily 60°C
Intensive 70°C
Available
options
— Crockery to be washed later . — — 4.0 0.03 14±
—
Loading instructions
Lightly soiled crockery, without dry
residuals.
Normally soiled crockery. Ener gy-saving
programme.
Normally or heavily soiled crockery. X X 13.0 1.25 120 ±
Recommended programme for heavily
soiled crockery, especially suitable for
pans and saucepans.
Detergent
dispenser
large small Litres kWh Minutes
X — 10.0 0.65 30±
X X 12.0 1.05 165 ±
X X 14.0 1.55 155 ±
for more detailed information on
Consumption
1)
5019 496 01102
1)
1)
1)
1)
1)
1
2. QUICK REFERENCE GUIDE
Detailed instructions are given on the following pages; also see section “5. What to do, in case of...”
1. Switch on the
appliance
2. Select a programme
3. Select the type of
detergent
4. Fill in the detergent
5. Check the rinse aid
level
6. Check the salt level
Press the
Press the button “Select programme” or the programme selector to display the
selected programme. If required, select possible options.
The detergent selection procedure varies depending on the dishwasher model.
Chapter “1. Overview” provides instructions for selecting detergent type.
4a. Powder/gel/tabs
Fill the detergent dispenser compartments in
accordance with the wash programme selected.
Large compartment A for every wash cycle, additional
small compartment B for programmes with pre-wash
(see table 1.1.).
4b. Combined action detergents (2 in 1/3 in 1/... etc.)
Place the detergent in compartment A, as per the
manufacturer's recommendations.
Depending on the model:
/OFF button.
ON
ACB
Visual indicator in dispenser
dark
clear
The indicator lamp on the control panel lights up when rinse aid
needs to be added. Not all models are equipped with such an
indicator.
window in salt reservoir cap on bottom of appliance inside
orange
clear
The indicator lamp on the control panel lights up when salt needs
to be added. Even once salt has been added, the indicator lamp
only switches off after several wash cycles!
sufficient rinse aid present,
➯
add rinse aid (approx. 150 ml).
➯
when sufficient salt is present,
➯
when salt needs to be added.
➯
C
7. Load the racks
8. Open the water tap
and close the door
9. Start the appliance
Wash cycle
10.End of programme
11.Switch off the
appliance
12.Turn off the water
tap, unload the racks
2
Make sure that the spray arms can turn freely and are not impeded by crockery
or cutlery in the racks.
Detailed instructions on loading the racks are given in chapter “3. How to use
the appliance”, under “How to load the racks”.
Changing the programme
in progress:
Press the START button.
If the appliance is switched off during a
wash cycle, when switched on again it will
resume the cycle from where it was
interrupted. Care must be taken when
opening the door, as steam will escape!
The START indicator lamp switches off at the end of the programme.
Press the
Unload the appliance, starting from the lower rack in order to avoid any
residual drips of water falling onto crockery below.
button. All the indicator lamps switch off.
OFF
- Keep the START button pressed
for about 2 seconds until the
START indicator goes off.
- (Water drains for up to 60
seconds).
- Select the programme again.
- Press the Start button.
3. HOW TO USE THE APPLIANCE
PROGRAMME SELECTION
Press the button “Select programme” or the programme selector to display the selected programme. The
appliance must be switched on. If required, select possible options. The corresponding indicator lights up. The
correct programme and the selectable functions are given in table 1.1 on page 1.
Programme times stated in the table were obtained under normal conditions and may vary
depending on conditions. Differences of up to 20 minutes are possible with sensor programmes
as a result of the appliance's automatic calibration system.
HOW TO FILL THE DETERGENT DISPENSER
Only fill the detergent dispenser prior to starting a wash programme.
specially recommended for dishwashers, observing the manufacturer's recommended dosage.
Observe the manufacturer's safety warnings!
Open the detergent dispenser compartments by pushing the left button (button 1) of the dispenser.
a. Powder/gel/tabs
Fill the detergent dispenser compartments in accordance with the wash programme selected (table 1.1).
Programmes without pre-wash:
pour the entire recommended dosage into compartment A.
Programmes with pre-wash:
pour 2/3 of the recommended dosage into the large compartment
and 1/3 into the small compartment B.
A
Dishwasher tabs should be placed, according to the
manufacturer's recommendations, in compartment A.
If the “Half load” option is selected, detergent dosage should be
reduced by approximately 1/3.
b. Combined action detergents (2 in 1/3 in 1/... etc.)
Combined action detergents should be placed, according to the
manufacturer's recommendations, in compartment A.
Firmly close and press the detergent compartment lid shut after filling.
Detergents with rinse aid incorporated may be effective only with longer programmes. In the
case of shorter programmes, detergent residue may be a problem (if necessary, use powder
detergent). Detergents with rinse aid incorporated tend to form excess suds.
The guarantee is not applicable if faults are caused by the use of these products.
Large
compartment
A
use detergents
Only
button
1
compartment
Small
B
HOW TO CHECK/FILL/ADJUST RINSE AID
Not necessary when using a combined action detergent.
a. How to check the rinse aid level
Check the visual indicator C on the rinse aid dispenser: dark = sufficient rinse aid, clear = add rinse aid.
In the case of appliances with an electric indicator on the
control panel, the rinse aid indicator lamp lights up red
when rinse aid needs to be added.
b. How to fill the rinse aid dispenser
Open the rinse aid dispenser by pressing the right button
(button 2) of the dispenser.
Fill the dispenser with rinse aid up to the “max” line
(approx. 150 ml).
Shut the lid again.
Only use rinse aids recommended for use in domestic dishwashers.
any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault
function of the appliance.
Immediately
wipe away
Indicator
max
button
C
2
3
Loading...