Page 1
GB
GSI 4743
Rinse aid level indicator
Add rinse aid.
Salt level indicator
Add regeneration salt; only add regeneration
salt immediately before starting a wash
programme.
Quick Reference Guide
Further indications are given in the pages to follow and in the user instructions.
Programme progress indicator
Pre-rinse /
Preliminary
washing
Washing
Options
Delayed start button
The wash cycle can be programmed to start after 3-6-9
hours. Then press the Start button.
The dishwasher will start at the set time.
Drying
Programme end
Start button
Indicator lamp lit while the dishwasher is
operating.
Flashes when a fault occurs.
Switches off at the end of the programme.
Off (Programme selector)
On (Programme selector)
Place the detergent into the:
Programme Symbol
and Temperature
Pre-rinse
Rapid 40° C
Bio-Normal 50° C2)
Normal 65° C
1) Values may vary in relation to usage, e.g.: different loads,
water temperatures - above or below 15° C - as well as water hardness and power supply voltage.
2) Programme recommended when using detergents of type B (enzyme-based detergents). Reference programme on the energy label.
3) Programme recommended when using detergents of type A (non enzyme-based detergents).
3)
Crockery to be washed later.
lightly soiled crockery with no dried-on food.
Normally or heavily soiled crockery with dried-on food.
Normally or heavily soiled crockery.
Programme selection and
recommended load type
small
compartment
- - 5.0 0.02 9
- X 13.0 0.85 30
X X 16.0 1.03 120
X X 16.0 1.55 86
compartment
(We reserve the right to make technical modifications)
large
Consumption1)
Normal load
Water
(Liter)
Energy
(kWh)
5019 100 90212
Time
(Min.)
Page 2
B
A
C
How to use the dishwasher
1. After loading the dishwasher, close the
door properly and open the water
supply tap.
2. The dishwasher switches on
automatically as soon as the progra mme
selector knob is turned.
programme indicator lamps will
illuminate.
3. Turn the selector knob to select the
desired programme.
corresponding indicator lamp lights
If required, select options
up.
(if supplied).
4. Press the Start button to start the
selected wash programme.
indicator lamp will illuminate.
set, the programmed data cannot be
altered by turning the programme
selector knob.
once the Start button has been
Note:
pressed, the dishwasher memorises the
last programme selected. This
information remains in the memory even
during interruption of the power supply.
To change the selected
programme, press the Start
button for about 5 seconds,
the Start indicator lamp
switches off.
programme using the
programme selector knob and
press the Start button.
If the dishwasher is switched off
Note:
during a wash programme, when
switched on again the dishwasher
resumes the wash cycle from where it
was interrupted.
Only open the dishwasher door if
strictly necessary during a wash
cycle and exercise maximum
caution. Danger of scalding from
5. To indicate the end of the programme,
steam.
the Start indicator lamp switches off
and
the End indicator lamp (if fitted)
switches on
(for about 30 min.)
The
Select a new
One of the
The Start
Once
.
6. Turn the programme selector knob
counter clockwise to the “0” position to
switch off the dishwasher (only after the
Start indicator lamp has switched off).
All the indicator lamps switch off.
7. Open the door (warning: beware of hot
steam). Unload the lower rack before
the upper one. Close the water tap.
Upper rack
.
until
Rack height adjustment:
(The dishwasher is delivered with the upper
rack in the top position).
The rack height can also be changed
when loaded.
Upper and lower rack
• To lower: pull out the
handles and gently lower the rack.
• To raise: pull up the
until the rack clicks into place.
• The rack must be level on both sides.
Crockery Holders:
•Down:
cups and long-stemmed glasses.
•
Up: plates.
“Vario Organizer” Multi-purpose
support:
• To be used, for example, for longhandled utensils
with the blade facing downwards),
cups and glasses.
• May be used in three different
positions (see also “Dishwasher
loading instructions” on Page 4).
1. Upon the left-hand side of the rack.
2. Upside-down, towards the centre of
the rack.
3. Upside-down, towards the left side.
Glass holder:
two
side handles
two
(arrange knives
side
Lower rack
B
A
C
Plate holders:
• May be lowered to increase
available space (A).
• May be removed to increase available
space(B). To remove: pull the handle
upwards.
Cutlery basket:
The cutlery basket (C) may be removed
to increase available space.
Please read the user instructions carefully.
Page 3
• Arrange crockery so that items do not
touch each other. Arrange large
crockery in the lower rack and smaller
crockery in the upper rack.
• Load cups at an angle to facilitate
water drainage.
• Generally speaking, place cutlery in the
basket with the handles positioned
downwards, but ensure that any sharp
knives and forks that might cause
injury are placed in the basket with the
handles positioned upwards.
• Make sure the water jet can reach all
loaded items and that the spray arms
turn freely.
Important
• Fill the detergent dispenser and check
the salt and rinse aid level.
• Do not use the appliance for items not
suitable for washing in a dishwasher,
for example: wooden items, aluminium,
plastic utensils, tin, hand-decorated
crockery (unglazed), silver cutlery.
• Do not put liquid fat in the dishwasher
(e.g. oil used for frying) or candle wax.
• If a fault occurs or you wish to change
the current programme, press the
“START” button for about 5 seconds
until the Start indicator lamp switches
off.
• If regeneration salt is to be added
Tips and advice
immediately
in order to eliminate any residual salt
(rinsing alone is not sufficient).
• If a regeneration salt i s to be added,
IMMEDIATELY start a wash
programme, in order to eliminate any
residual salt (rinsing alone is not
sufficient).
start a wash programme
• Before starting a wash programme,
make sure that the spray arms can turn
freely and are not blocked by crockery
or cutlery.
Switch off the dishwasher once the
•
“Start” indicator lamp has switched off.
If you switch off the dishwasher during
a wash cycle, when switched on again
the dishwasher resumes the cycle from
where it was interrupted without having
to start it again
If a fault occurs, before contacting our
After-Sales Service, make the following
checks to try and remedy the problem:
The dishwasher is not working:
• Is the plug properly inserted in the wall
socket?
• Is there a power failure?
• Is the dishwasher switched on?
• Has the Start button been pressed?
• Has the delayed start timer been set
(if fitted)?
• Is the water supply tap on?
• Is the flow of water obstructed by impurities?
If so, close the water supply tap, detach the
water hose and clean the filter. Then
re-connect the water hose to the tap and
open the water tap once again.
• Are the filters clogged?
(See “Care and maintenance” chapter in
the user instructions).
• Is the door closed properly?
• Is a fault indicated?
(The Start indicator lamp flashes).
Start the programme again from the
beginning: Press the Start button for
about 5 seconds, until the Start indicator
lamp switches off.
Select a new programme and press the
Start button.
.
Troubleshooting Guide
Crockery still dirty after washing:
• Was the crockery loaded properly?
• Crockery must be loaded facing
downwards; make sure, especially for
large crockery.
• The water jets must spray the entire
surface of all items.
• Make sure that crockery and cutlery are
arranged properly.
• Have you selected the correct programme?
• Did you use too much or too little
detergent? (The use of poor quality
detergents result in less effective
washing).
• Are the filters clogged or incorrectly
assembled? (See “Care and
Maintenance” chapter in the user
instructions).
• Are the spray arms blocked or the nozzles
clogged? (See “Care and Maintenance”
chapter in the user instructions).
• Is the lower spray arm correctly fitted?
• Is the salt container cap (water softening
system) screwed down?
Marked crockery:
• Is the water hardness level selector not
properly adjusted? See (“Filling the salt
container” in the user instructions).
• Is the salt container empty?
(See “Filling the salt cont ainer” in the user
instructions).
• Was insufficient detergent used?
(See “Filling the detergent dispenser ” in
the user instructions).
Marked glasses and cutlery:
• Was too much rinse aid used?
(See “Filling the rinse aid dispenser” in the
user instructions).
Note:
With some models, when the Start
button is pressed a pre-wash cycle precedes
the actual wash programme; This
regenerates the water softening system.
AFTER-SALES
SERVICE
If, after carrying out the above checks the
malfunction persists or appears again,
turn the appliance off and turn off the
water supply tap, then call our After-Sales
Service (see guarantee). Please specify:
• The nature of the fault.
• The appliance type and model.
• The service code (the number after
the word Service on the
adhesive rating plate) inside the door on
the right-hand side.
Your full address and telephone number.
•
Please read the user instructions carefully.
Page 4
Dishwasher loading instructions
UPPER RACK
LOWER RACK
Depending on the model, rack features may vary (see “Upper and lower rack” description).
Loading...