Bauknecht GSI 110 ECO IN, GSI 110 ECO WS Quick Reference Guide

.
Quick reference guide
PROGRAMME SELECTION BUTTON
(See “Table of programmes” below)
START BUTTON
The indicator lights up during operation, flashes when a fault occurs, and goes off at the end of the programme.
START BUTTON RESET FUNCTION:
Press this button for at least 2 seconds; the selected programme and options will be cancelled. Main failure displays (repeated flashing of the START indicator lamp) can be cancelled by RESETTING. Detailed instructions are given in chapter “What to do if...”.
START
MULTI
DELAY
ZONE
option
(see at right for options description)
ON/OFF
BUTTON
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE INSTALLATION INSTRUCTIONS! THE GUARANTEE IS NOT APPLICABLE IF FAULTS ARE CAUSED BY INCORRECT USE OF THE APPLIANCE.
Options and display description
SALT INDICATOR
When lit, the salt reservoir needs to be refilled.
FAULT INDICATION AND WASH TIME DISPLAY
In normal operation it indicates the remaining time (h:mm), whereas with “Delayed start” selected it indicates the time remaining until programme start (hh). If “F..” appears on the display, see chapter “What to do if...”.
Chart
Table of programmes
Detergent
X 7-17 0.99-1.75 65-220
X 10.0 0.85 100
X*10.0 0.65 30
X 13.0 1.50 115
X 13.0 1.20 290
50°C
Available
options
Delay
Multizone
Delay
Multizone
Delay
Multizone
Delay
Multizone
Delay
Multizone
Delay
Multizone
Delay
Multizone
Loading instructions Litres kWh
Normally or heavily soiled crockery, including pots and pans. Thanks to steam action, soaking or hand pre­treatment is no longer needed. In addition hygiene is ensured due to the high temperature steam.
Crockery to be washed later. 4.0 0.03 14
Light soiling, for example glasses and cups.
Lightly soiled crockery, with no dried-on
* Use of tablets not
food.
recommended.
Normally soiled crockery. X 13.0 0.93 200
Normally or heavily soiled crockery , with additional antibacterial wash. Progra mme interruption (e.g. due to door opening) can compromise elimination of germs.
Normally soiled crockery, gentle and quiet thanks to the lower spray pressure (39 dbA).
P
1
2 3 4 5
6 7
1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of the appliance’s automatic calibration system
2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
Programmes
Steam Sensor + 40-70°C
Pre-Wash cold
Glasses 40°C
Quickwash 40°C
Bio Normal
Antibacterial
Overnight 55°C
2)
3)
Consumption
Minutes
1)
RINSE AID INDICATOR
When lit, the rinse aid dispenser needs to be refilled.
DELAYED START BUTTON
Press the button (repeatedly) to delay the start of the programme. Adjustable from 1 to 24 hours. With each press of the button, the delayed start indicator increases by one hour and after 24 restarts from 00. Then press the START button. The dishwasher will start after the set time.
HALF LOAD/ MULTIZONE
Allows you to choose the washing zones. Press this button to select the wash zones:
both racks
only upper rack
only lower rack
5019 496 01609GSI 110 Eco
GB
-1-
How to set detergent type: powder/gel/tablet (if option is available)
First time use
In order to always ensure the best cleaning results, you NEED to set: DETERGENT type and WATER HARDNESS.
1- salt reservoir 2- rinse aid dispenser 3- detergent dispenser 4- racks system 5,6,7,8- available functions on the panel 9- filters 10- spray arms
1.
Select 3rd programme (see Table of programmes
- page 1)
2.
Press START button for 7 seconds
3a.
Check your detergent type...
Detergent
types
Powder or gel
(factory setting)
Tablet 2 in 1
Tablet 3 in 1
Tablet All in 1
For models without “detergent type” option, the salt and rinse aid indicators will be lit when tablets are used.
How to set water hardness
Switch on the appliance
*
before the first wash
only
water hardness has been changed
1.
Ask your water supply company what the
German
degrees °dH
0 - 5 0 - 9 0 - 6.3 Soft 1 1x
6 - 10 10 - 18 7 - 12.6 Medium 2 2x 11 - 15 19 - 27 13.3 - 18.9 Average 3 3x 16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4 4x 22 - 28 38 - 50 26.6 - 35 Hard 5 5x 29 - 35 51 - 63 35.7 - 44.1 Very hard 6 6x
36 - 60 64 - 107 44.8 - 74.9
French
degrees °fH
or if the
degrees °eH
English
- Select the 2nd programme “P2” - consult the table of programmes.
- Press the START button for at least 5 seconds until the START indicator lamp flashes.
- The water hardness setting is shown on the display (if present) or the START button flashes.
- With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again.
- The appliance must be switched off to memorise the new setting.
water hardness
is...2....enter this value on your
dishwasher
Water
hardness
Extremely
hard
Dishwasher
with display:
insert value in
the display
7 7x
3b.
...and set it on your dishwasher
using the START button
(as per table below)
Dishwasher models
model without
display
3h 6h 9h
Dishwasher
without
display: count
START button
led flashes
model with display
Suggestions for detergent use
Gel or Powder
(rinse aid and
salt)
go to step 1
(see “Daily
check”)
4.
Remember to use salt and rinse aid when needed (as indicated below)
no symbol add salt add rinse aid
add salt
salt
Tablets
rinse aid
rinse aid
Water hardness level is factory set for medium hard water (a number “4” is shown on the display or the START indicator lamp flashes 4 times).
if extra salt is needed go to
step 1
(see “Daily
check”)
Even if you use tablets which include salt, you must still add salt since such detergents are not effective enough at softening hard water.
5.
Switch off and switch on again to save setting
GB
-2-
1
Filling the salt reservoir -
Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Daily check
The salt level indicator lamp may remain lit for the duration of several wash cycles. If the water hardness level falls within category (soft),
Adding rinse aid
(not necessary when you use tablets). How to adjust the rinse aid dosage regulator
2
Rinse aid indicator (depending on model)
Only use rinse aids recommended for use in domestic dishwashers. If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly d ry : incr e a s e the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid
setting will not improve the situation. Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend
to form excess suds.
Adding detergent -
3
S
E
L
Visual indicator (depending on model). Unscrew cap.
Visual indicator
If required, open the cover B (press right button).
no
salt is required.
The indicator lamp on the control panel lights up when RINSE AID NEEDS TO BE ADDED.
Immediately
Fill the salt reservoir with water before the first wash only.
S
E
L
Salt indicator
(depending on
the model)
Add rinse aid to the max. line ~150 ml
wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.
The indicator lamp on the control panel lights up when SALT NEEDS TO BE ADDED.
Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Tablet / gel / powder
Use only one tablet per one
Open the cover A (press left button).
Only fill the detergent dispenser prior to starting a wash programme.
cycle, only placed in detergent dispenser.
All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory.
S
Add salt
(never add detergent!). min. 1.5 kg
S
max. 2 kg
E
L
orange: OK. clear: NEEDS TO BE ADDED
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.
dark: OK. clear: NEEDS TO BE ADDED
By pressing dedicated ribs shut the cover.
E
L
Visual indicator (depending on model). Screw on the cap. Salt residues around cap need to be removed.
Daily use
GB
-3-
Loading...
+ 5 hidden pages