Please read these instructions carefully before starting
installation and keep in a safe place for future reference.
Check the contents of the pack carefully before installation.
Bauhaus will not be held responsible for any de-t / re-t costs
where faulty product has been tted.
If any fault is found with materials or workmanship, it must be
reported immediately to the manufacturer. Remedial action will be
taken, based on information received, on condition that:
1. Full details are supplied to the manufacturer; 2. The product
has not been modied or tampered with; 3. The manufacturer is
informed of any damage/shortages prior to installation.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Advice & Safety
This product should only be installed by a suitably qualied
Plumber/installer. Should the installation be completed by a
non-qualied person any product guarantee maybe considered
invalid. For a claim made under our warranty written certication
of your installers qualications can be required.
It is advised that all doors and drawers are removed prior to tting
to avoid unnecessary damage occurring.
Ensure the room is well heated and ventilated.
It is recommended that walls are fully tiled before furniture and
accessory installation. This ensures that the product is installed
at to the tile face and allows product to be easily removed if
required in the future.
These instructions have been prepared for your guidance, you
must exercise due care at all times.
Please note that some units are heavy. Always take care when
lifting, and follow health and safety guidelines. It is recommended
that 2 people carry out the installation of larger basin/vanity units.
Handle glass with care. Although the glass supplied is toughened
safety glass (to BS6206), impacts can damage both the glass and
the furniture.
Warning! Please check for any hidden pipes or electrical cables
before drilling holes in the oor or walls.
When using power tools always follow the manufacturer’s user
instructions.
Care & Cleaning
NEVER use products containing bleach, cleaners of a gritty or
abrasive nature or so called “glass and mirror” cleaning products
Use a well wrung chamois leather or micro bre cloth for furniture
carcasses.
Resin wash basins should only be cleaned with a mild detergent
or warm soapy water; in hard water areas a good quality limescale remover can be applied.
Clean mirrors only with a micro bre cloth.
If any maintenance is required then it must be carried out by a
qualied Plumber.
IMPORTANT - Advice and safety - Please read before installation
Tools & equipment needed: Drill, 8mm Suitable drill bit, Phillips screwdriver, Spirit level, Ruler/tape measure, Pencil,
Silicone sealant (clear).
BATHROOM FURNITURE RANGE
ELITE
INSTALLATION INSTRUCTIONS
Including 4 pre-fitted shelves Including 1 pre-fitted shelves Including 2 pre-fitted shelf
Tower Storage Unit
Short Storage Unit
EL3514FEL3548F
Half Tower Storage Unit
EL3580F
x2x2
x2
2
380mm 390mm
Plan unit position
We suggest positioning the
tower unit so it is level with
any other unit that has been
installed.
Step 2
Step 3
Remove the doors before installation.
a: Lift the tab (shown) on all 4 hinges, to release.
b: Pull doors back.
ba
Step 1
a: Use the measurements opposite to
position the ‘hanging hooks’ on to the wall.
b: Mark the xing hole positions onto the
wall.
Drill Ø 8mm holes, insert the wall plugs
and the ‘hanging hooks’.
c: The ‘hanging hooks’ should protrude
from the wall by 5-7mm.
Position the unit on the ‘hanging hooks’.
a b
b
c
Step 4
a: Check the unit is level.
If leveling is required: inside
the unit, use a screwdriver to
adjust the hanging position.
d: To lift or lower the unit
adjust the screw shown.
c: To move the unit closer or
further from the wall adjust the
screw shown.
a
280mm
35
mm
Back
of unit
35
mm
280mm
5-7mm
c
Storage Unit installation - Half Tower Storage Unit is shown as a typical example
3
If changing the door opening side or the door alignment needs adjusting, follow the
instructions on the next page.
Step 5
Note: Only re-t doors now if not changing the opening side.
Re-t doors:
a: Reposition of hinges onto the hinge plates.
b: Push the front until the hinge ‘clicks’ into position.
ba
For any further information please contact
Bauhaus on: 0845 873 8840
Or visit our web-site at:
www.bauhaus-bathrooms.co.uk
The manufacturer reserves the right to make technical
modications without prior notice.
To move door up or down: Turn screw
shown to move door up or down to suit.
To move door in or out: Turn screw
shown to move door in or out to suit.
To move door left or right: Turn screw
shown to move door left or right to suit.
a: Lift tab (shown) on all hinges, to release.
b: Pull door back. c: Lift the hinge plate tabs.
d: Remove the hinge plates. e: Re-t hinge plates on the
opposite side. f: Fold hinge plate tabs back.
g: Rotate door, so hinges on the door are now on the same
side as the hinge plates.
h: Reposition all hinges onto the hinge plates.
i: Push the front until the hinge ‘clicks’ into position.
Changing door opening side
Hinge adjustment
a b
c
d
Remove
e f
Re-t
h
i
g
Loading...