Bauer NE User Manual

Bauer Products, Inc.

702 Evergreen St SE
Grand Rapids, MI 49507
1-866-68-BAUER(22837)
[phone]
[phone] fax

BP

Bauer NE

Thank You for purchasing the
convenience and security. We are a family owned company with over 50 years of service in the locking
hardware industry, and we are grateful for the opportunity to serve you. Please review and follow the
Installation, Programming, and Operating Instructions to ensure proper function.

Bauer NE

.. We have developed the

Bauer NE

with the idea to increase your

The

Bauer NE

 The first self-contained electronic RV latch with Capacitive Touch Technology.
 An integral touch pad to the latch which controls the dead bolt.
 It is powered by 4 AA batteries.
 Is retrofitable in most RV entry doors, and is easy to install.
 Programmable with a 4 digit PIN number.
 The large buttons are easy to see and use.
 Proximity sensing which illuminates the buttons.
 An Intelligent Keyless Entry System which knows the position of the deadbolt and indicates low

 The key will always be able to operate the paddle or dead bolt lock in case of the user forgetting the

Bauer NE

features:

battery strength, as well as providing audible feedback to successful locking and unlocking functions.

code or dead battery

Installation Instructions:

 The following steps are graphically shown on the enclosed

1. Remove old lock.

2. Clean cut-out. Remove any dirt, loose material, etc.

3. Install outside housing (the portion that includes the Touch Pad) with the dead bolt in the

unlocked position.

4. Attach the (2) 8x32 screws into the portion of the handle that has the Plunger and Dead

Bolt. This is on the edge of the door.

5. Plug wire from Inside Plate Assembly into the receptacle on the housing. DO NOT PICK UP

INSIDE PLATE ASSEMBLY BY PLUG. Make sure to align the tab on the plug properly with
the slot on the receptacle. The plug should make a slight click when properly engaged.

6. Tuck Battery Wires into pocket next to Stamped Steel Plate. Do not allow Battery Wires to

get between Inside Plate Assembly and Stamped Steel Plate as it will cause the motor to
bind.

7. Align the Dead Bolt Knob in the unlocked position. The Red Dots on the Dead Bolt Knob

and the Inside Plate Assembly should be aligned to indicate the unlocked position of the
Dead Bolt. Slide Dead Bolt Knob over D-Stem and align the 4 screw bosses on the housing
with the attaching holes on the Inside Plate Assembly. When Inside Plate Assembly is in

position with Housing install the (4) 8x32 Screws. Secure but do not over tighten screws.

Bauer NE

Installation schematic.

 Page 2 March 23, 2015

BP

BP

Battery Installation:

The

Bauer NE

application. Batteries not included.

Fresh batteries should be installed as necessary. Battery Life is highly dependent upon battery quality, usage,
and environment (temperature). Remove batteries if the lock will not be used for extended periods of time.

The following steps are shown on the enclosed Battery Installation schematic.

1. Loosen (2) 6x32 Captured screws on Battery Compartment Lid. These screws are captured to the

2. Install the AA batteries in accordance with the orientation shown in the Battery Compartment. The

3. Install Battery Compartment Lid by aligning the (3) tabs on the lid with the (3) slots on the Inside

4. Tighten the (2) 6x32 Captured screws back to attach the Battery Compartment Lid to the Inside

uses 4 AA batteries for operation. We do not recommend zinc carbon batteries for this

Battery Compartment Lid so they will not fall out.

batteries will fit tightly. Please verify the batteries are touching the contacts on both sides in the
Battery Compartment.

Plate Assembly. These tabs act as a hinge for closing the Battery Compartment Lid.

Plate Assembly.

Bauer NE

Description

The

“5|6”, “7|8”. The button labeled “1|2” is the same button whether the number 1 or 2 is desired. Please note this

handle uses Touch Technology. The buttons are activated by Touch and does not require pressing the
buttons. Touch the button and lift finger from button for proper code entry.

Operation

The
the lock you first must “wake up” the lock. To “wake up” the lock you must touch the area next to the
buttons. The buttons will illuminate once the Touch Pad is wakened. This indicates that the Touch Pad is
ready for the code to be entered.

Preset Factory Code

The

with the symbol is the Enter button, and is required to be touched after the code is entered. The
factory code resets every time the batteries are removed for at least 10 seconds.

Programming New Code

To set a new code, touch and hold the “3|4” button and the Enter Buttons for 2 seconds. The
provide three short beeps, indicating it is ready to accept a new code. Enter the new 4 digit code followed by

the . The
the new 4 digit code is entered there will be a long beep indicating the new code is accepted. The new code
can be entered now and will activate the dead bolt.

To reset the code, remove the batteries for at least 10 seconds. Re-install the batteries; and follow the steps to
Programming New Code.

Operation and Programming Guide:

Bauer NE

Bauer NE

Bauer NE

is a 4 touch pad button programmable deadbolt lock. The 4 buttons are labeled “1|2”, “3|4”,

incorporates proximity sensing to determine when you want to activate the lock. To operate

has a factory set code of 3,7,1,5 followed by the Enter button. The button

Bauer NE

will provide four short beeps to indicate new code has been entered. The first time

Bauer NE

will

 Page 3 March 23, 2015

BP

Quick Lock Feature – Look for Sticker Indicating this feature on Battery Compartment Lid

Once your personal code has been entered the
the “7|8” and the . Please note this feature is only activated once the personal code is entered.

Bauer NE

can be locked by simultaneously touching both

Please Enter Personal Code upon Installation of
Lock to prevent inadvertent programming.

Bauer NE

Action

Ready to Accept New Code Three short beeps

New Code Entered Four short beeps

Wrong Code Entered One long beep

Dead Bolt Locks Two short beeps

Dead Bolt Unlocks Two short beeps

Fault Logic

Bauer NE

Response

Dead Bolt fails to Lock One long beep

Dead Bolt fails to Unlock One long beep

Low Battery Button Lights Blink during “wake up” and

One Long beep after the Lock/Unlock beeps

The lock will cycle up to 10 more times once the low battery indication occurs. After this the final electric
function in a low battery condition will be unlock and not lock until the batteries have been replaced. Please
note that if the deadbolt is in the locked position and the batteries die the deadbolt will remain locked. The
key will always be able to activate the deadbolt lock.

General Maintenance and Operating Guidelines

 Install fresh batteries as necessary. The

with fresh, high quality AA batteries. Battery life is highly dependent upon battery quality, usage,
and environment (temperature).

 Make sure there are no obstructions in the door frame to prevent Dead Bolt extension.
 Do not wash with power washer or high pressure cleaner. The Bauer NE is designed to resist water

intrusion to protect its electrical components from normal water encounter such as rain.

 The

Bauer NE

uses Touch Technology. The buttons are activated by touching not pressing.

Bauer NE

is designed to function for months of normal usage

 Remove batteries when storing or not using this lock for extended periods of time.

Installation and Operation Videos available at

www.bauerproducts.com

 Page 4 March 23, 2015

BP

BP

Rain Sensing Technology

The

Bauer NE

up the touch pad and illuminate the Buttons. After a few seconds of contact from rain (water) the lights will
turn off, but a code still can be entered and the lock will function normally. The same effect will occur if the
operator continues to touch the touch pad for a prolonged period of time. Initially the Buttons will
illuminate, but then turn off. Again the lock will function normally in this case as well.

Additional Security Feature

The

Bauer NE

you enter your code you can continue to enter digits after the first four prior to touching the enter button
For example, if your code is 8,1,3,9 and you felt as if you were being watched you would enter 8,1,3,9 then

continue to touch additional digits prior to touching the enter button and the lock will operate.

Troubleshooting

Problem Possible Fixes

After Installation the Touch Pad does not work -Batteries are dead

-Batteries are not installed properly

-Plug not engaged properly

Dead Bolt not engaging into Door Frame -Obstruction in Door Frame

Code not working -Remove Batteries for 10 seconds then
Program New Code

Inside Paddle not Opening Latch -Inside screws are not secured to the
Housing.

Buttons Light but Dead Bolt does not activate -Replace Batteries

If the problem is not found on this list please call 1 866 682 2837 for assistance.

Limited Warranty

BAUER’S WARRANTY IS LIMITED. AT ITS SOLE DISCRETION, BAUER MAY EITHER REPLACE OR
REPAIR ANY DEFECTIVE PARTS. IN NO EVENT SHALL BAUER HAVE ANY LIABILITY TO
CUSTOMER FOR PAYING INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING
(WITHOUT LIMITATION) DAMAGES RESULTING FROM PERSONAL OR BODILY INJURY OR
DEATH OR DAMAGES TO, OR LOSS OF USE OF, ANY PROPERTY. NOTWITHSTANDING ANY
PROVISION TO THE CONTRARY, THIS LIMITED WARRANTY IS MADE UPON THE EXPRESS
UNDERSTANDING THAT IT SHALL APPLY IN CONNECTION WITH THE SALE OF THE
PRODUCT BY BAUER AND IS IN LIEU OF ALL OTHER WARRANTIES (EXPRESS, IMPLIED OR
STATUTORY) INCLUDING THE SEPARATE WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE OR USE.

possesses Rain Sensing Technology in order to preserve battery life. Please note rain will wake

recognizes the first four digits entered as the code. However, if you feel someone is watching

 Page 5 March 23, 2015

Installation and Operation Videos available at

www.bauerproducts.com

 Page 6 March 23, 2015

Installation and Operation Videos available at

www.bauerproducts.com