Battery Tender PN 022-0179 Installation
WARNING–RISK OF EXPLOSIVE GASES
WORKING WITH LEAD ACID BATTERIES AND BATTERY CHARGERS:
All lead acid batteries have the potential to emit gasses that may combine
into a combustible or explosive mixture. In many cases, it is possible that
lead acid batteries will emit these gasses during normal discharge and
charging operations. Because of this potential danger, it is important that
you follow the precautions recommended by both the battery and battery
charger manufacturers before using either one
.
WARNING
WHEN YOU WORK NEAR LEAD-ACID BATTERIES:
1. Someone should be within range of your voice or close enough to come to your
aid if you have an accident;
2. Have plenty of fresh water and soap nearby in case battery acid contacts skin,
clothing, or eyes;
3. Wear complete eye protection and protective clothing. Avoid touching your
eyes while working near a battery. If battery acid contacts your skin or
clothing, wash immediately with soap and water. If acid enters an eye,
immediately flood the eye with running cold water for at least 10 minutes and
get medical attention as soon as possible;
4. Be extra cautious when handling metal tools around a battery. If you drop a
metal tool near a battery it might spark or create a short circuit between the
battery terminals and some other metal part. Either event may cause a
dangerous electrical shock hazard, a fire, or even an explosion;
5. Remove all personal metal items such as rings, bracelets, necklaces, and
watches when working with a lead-acid battery. A lead-acid battery can
produce a short-circuited current high enough to weld a metal ring or other
piece of jewelry, causing a severe burn.
DELTRAN CORPORATION
801 International Spee
dway Blvd.
DeLand, Florida 32724
Phone 386-736-7900 FAX 386-736-0379
www.batterytender.com
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS:
This manual contains
important safety and operating instructions for the DELTRAN
BATTERY TENDER® POWER PRO Modular Marine Charger
CAREFULLY READ THESE INSTRUCTIONS BEFORE USING
THIS DEVICE.
WARNING AND CAUTION LABEL DEFINITIONS:
WARNING indicates a potentially hazardous situation, which, if
not avoided, could result in serious injury or death.
CAUTION indicates a potentially hazardous situation, which, if
not avoided, may result in minor or moderate injury.
CAUTION used without the safety alert symbol indicates a
potentially hazardous situation that if not avoided, may result in
property damage.
GENERAL PRECAUTIONS
WARNING
Battery posts, terminals and related accessories contain lead and
lead components, chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm. Always
wash your hands after handling these devices.
POWER PRO Modular Marine Battery Charger Assembly Instructions
The Battery Tender Power Pro Modular Marine Charging system components are sold separately. The three different components are
shown in Fig. 1-3. The modular base plate (three position or four position), the modular charger assembly, and the modular cover plate.
POWER PRO Modular Marine Charger
WARNING
CAUTION
CAUTION
Modular base plate
1 Base plate w/ power cord
3 bank P/N 024-0003
4 bank P/N 024-0005
1 Instruction manual
WARNING
Outlets on base plate
will only accept plug from modular
charger, never attempt to plug other
devices into base plate.
Suggested mounting hardeware:
1/4"-5/16" hex bolt or machine screw with hex nut and washers,
or 1/4"-5/16" lag bolt with washer.
Fig. 1
Modular charger assembly
1 Charger assembly w/ 6ft output cable
P/N 022-0179
2 M8 x 1.25 x 25mm bolt
2 M8 internal tooth lock washer
CAUTION
Maximum torque for
M8 x 1.25 x 25mm bolts is 10 ft-lbs.
Fig. 2
Modular cover plate
1 Cover plate
P/N 400-0221
2 M8 x 1.25 x 25mm bolt
2 M8 internal tooth lock washer
CAUTION
Cover plate must be installed in
all unused charger positions to prevent
shock hazard and damage to base plate
Fig. 3
WARNING
Never plug base plate into wall outlet during assembly.
Never attempt to plug a Modular charger assembly directly into a wall outlet.
Never plug anything other than a modular charger assembly or cover plate into the base plate.
Materials Required
1 Modular marine base plate 3 bank or 4 bank
1 or more Modular charger assemblies
Cover plates to cover any unused positions
Example: 4 bank base plate w/ 3 charger assemblies
1 Modular marine 4 bank base plate
3 Modular marine charger assemblies
1 Modular cover plate
Fig. 4
Assembly steps
1. Unpackage all components.
2. Verify all components present as listed in Fig. 1-3
3. Insert modular charger assembly plug into base plate socket. Fig. 4
4. Install M8 x 1.25 bolts w/ supplied washers into mounting tabs and torque to 10 ft-lbs.
5. Repeat step 4 for remaining modular charger assemblies.
6. In all base plate positions that remain unused install
modular cover plate. Fig. 4
7. Install M8 x 1.25 bolts w/ supplied washers into modular
cover plate and torque to 10 ft-lbs.
8. Mount base plate to solid surface with hardware suggested
in Fig. 2, allow for 4" of clearance from surfaces of charger
to allow for proper cooling.
9. Connect charger leads to battery/batteries, red lead to
positive terminal, black lead to negative terminal of each
battery. If batteries are wired in series make sure each DC
output is connected across only one battery. See Fig. 5 for
detail.
10. Connect power cord from POWER PRO Modular Marine
Battery Charger to an AC receptecal and allow batteries
time to charge.
Pos.
Neg.
Fig. 5
123
Loading...