Batribike 50930, 50713, 50935, 50707-2,50930,50935,50713 Display UPGRADES Options

batribike.com
Hand Built in Europe
ELECTRIC BICYCLES
Display Options
UPGRADES
Centre LCD
LED Display
Mini LCD
50713
50707-2
50930
50935
2
D E
A L
E R
S T A
M P
IMPORTANT PLEASE READ THIS MANUAL FULLY BEFORE USE
DISPLAY TYPE:-
LED
MINI LCD
CENTRE LCD
/
/
FITMENT DATE:-
DAY MONTH YEAR
BICYCLE SERIAL :-
FITTED and TESTED BY:-
3
Thank you for purchasing a Display Option for
your BATRIBIKE Electric Bicycle
This manual contains brief fitting notes intended for the Dealer and
User Instructions for each display type.
This manual should be left with the User after fitting.
Contents
Parts Identification ............................................ PAGE 4
Fitting Instructions ............................................ PAGE 6
Operating Instructions ...................................... PAGE 8
LED Option ............................................ PAGE 10
Mini LCD Option .................................... PAGE 14
Centre LCD Option ................................ PAGE 22
Troubleshooting ................................................ PAGE 31
Warranty ........................................................... PAGE 34
4
PARTS IDENTIFICATION
We continually strive to ensure that we provide you with the best possible products, therefore
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
1234567891011
Lights ON/OFF Button
Mode Button
Power Assistance Level Indication
Power UP Button
Charging Socket
Battery Charge Level Indication
Walk Assist (6 Km/h) Button
LCD Information Area
Throttle (Pedalling Only) / Walk Assist
Power ON/OFF Button
Power DOWN Button
1652347
FITTED AS STANDARD ON:-
OMEGA ALPHA SIGMA QUINTESSENTIAL
LED
CONNECTS TO BIKE WIRING HARNESS
PRODUCT PART NUMBERS
The following shows the ProMovec part numbers required for each display type and bike model.
Please ensure you select the correct size bracket if fitting a Centre Display
50713
50707-2
50930
50935
50937
50938
Centre LCD Bracket for handlebar diameter 32 mm
Centre LCD Bracket for handlebar diameter 22 mm
LED Display Unit
Centre LCD without Charging Socket (All models except PERDU)
Mini LCD without Charging Socket (All models except PERDU)
Centre LCD with Charging Socket (For PERDU)
5
Centre LCD
518
9
3
FITTED AS STANDARD ON:-
TEN
7
10
CONNECTS TO BIKE WIRING HARNESS
SWITCH UNIT
CONNECTION
5
718931011
ONLY USED ON PERDU
FITTED AS STANDARD ON:-
PERDU DELTA
Mini LCD
CONNECTS TO BIKE WIRING HARNESS
ON REAR
PERDU ONLY
11
PERDU
VERSION
STANDARD
VERSION
50930
50935
6
Dealer Instructions
Fitment of Display Upgrade
These instructions are designed to be used by Authorised BATRIBIKE Dealers and competent personnel.
It is important that you ensure that the existing display is operating correctly with no errors prior to fitting a display upgrade. Any errors or malfunctions must be rectified before following this procedure.
1. Trace the display connection cable from the display to where it enters the frame.
2. Gently unwrap the cable cover/spiral wrap to release the display cable.
3. Carefully remove plastic shroud from frame aperture using small flat bladed screwdriver inserted into rear of shroud to release the clip.
4. Gently pull the display cable from the frame aperture until the plug and socket can be seen.
5. Unplug the connecting plug from the wiring harness.
6. Remove the existing display from the handlebars. (It may be necessary to first remove the grip, brake lever etc.)
7. Depending upon display type is to be fitted:-
EITHER, for LED and Mini LCD
a. Fit the new display onto the handlebars (and then refit brake
lever, grip etc. as necessary).
OR, for Centre LCD
b. Fit the switch unit onto the handlebars, fit the centre display
onto the middle of the handlebars, connect the switch unit lead and the centre display taking care to use the correct plug, (and then refit brake lever, grip etc. as necessary).
7
8. Plug the new display cable into the wiring harness.
9. Test for correct operation.
10. Gently push the cable back into the frame aperture.
11. Refit plastic shroud ensuring the clip secures the shroud into the
frame aperture.
12. Refit the cable cover/spiral wrap.
13. Ensure that the user is provided with this instruction manual.
PLUG & SOCKET
PLASTIC SHROUD
DISPLAY
SPIRAL WRAP
AROUND
WIRING
HARNESS
INSIDE
FRAME
APERTURE
EXISTING
GENTLY INSERT SCREWDRIVER BLADE HERE
ALPHA MODEL USED AS EXAMPLE
OTHER MODELS SIMILAR
PLUG ON
DISPLAY
CABLE
SOCKET ON
WIRING
HARNESS
8
User Instructions
Your BATRIBIKE electric bicycle has a choice of display upgrade available. Refer to the following sections for Operating Instructions for each display type.
LED Display
See page 10 for operation.
The operation of the LED system provides adjustable SPEED in five selectable steps. Level 1 powers up to 6 mph, whilst level 5 powers up to 15 mph. Each level operates at up to full power, and power cuts out at the selected speed level.
9
Mini LCD
See page 14 for operation.
The operation of the Mini LCD system has four selectable POWER levels. Level 1 gives 25% of the power, level 2 - 50% up to level 4, 100% power. Speed range is from 0 to 15 mph in all levels. This is available as an easy to fit upgrade.
Centre LCD
See page 22 for operation.
The Centre LCD system provides more power levels than the Mini LCD and a larger display makes it easier to read. This is available as an easy to fit upgrade.
10
LED Operation
To use under electric power, switch on at the battery if required, (bike model specific), then press and hold the DOWN button on the handlebar LED display until the blue lights are seen.
Switching On
To turn off the LED and the power to the bike, press and hold the DOWN button for 2 seconds.
If the power is left on for an extended period and the bike is not used, then the power will automatically be turned off.
To fully turn off the power, switch off at the battery if required, (bike model specific).
Switching Off
Control Buttons
By means of the three buttons, UP, DOWN and 6 Km/h, on the handlebar mounted display unit, the various functions of the power controller can be utilised.
See the following sections for details.
11
Bicycle Lights
If your BATRIBIKE Electric Bicycle is supplied with lights on the front and rear, then these are switched on by pressing the LIGHT button on the handlebar display. To turn the lights off, again press the LIGHT button.
The top row of LEDs show the charge remaining in the battery. The indicators will gradually go out as the battery power is used up. Refer to the table below for details.
Battery Meter
70 - 100%
SYMBOL
DISPLAYED
CHARGE
REMAINING
BATTERY METER DISPLAYS THE CHARGE REMAINING IN THE BATTERY
BATTERY IS
EXHAUSTED AND
SHOULD BE
RECHARGED AS
SOON AS POSSIBLE
50 - 70%
30 - 50%
15 - 30%
0 - 15%
EMPTY
OR
First Light Flashes 8 Times
12
There are 5 levels of pedal assistance available from the motor. Using the UP and DOWN buttons you can select from Level 1 (Lowest), to Level 5 (Highest). The motor will then be activated upon pedalling.
Pedal Assistance
Please remember that the above values are provided as a guide. Due to manufacturing tolerances the performance may vary.
PEDAL ASSISTANCE FROM THE MOTOR
LEVEL
RANGE / SPEED
Provides maximum power when negotiating hills and head winds.
Great when needing to simply get from A to B as fast as possible.
Great for commuting to work.
EXAMPLE OF USAGE
Normal Use Mode.
These are the levels to use for everyday cycling. Gives good performance whilst maximising usable range per charge.
Best for Leisure Use.
Use these lower power levels when negotiating busy cycle paths and crowded areas. Also use when setting off and gradually increase through the levels for a smoother performance.
Ideal for negotiating obstacles.
up to 28 miles / 15 mph
up to 32 miles / 12 mph
up to 48 miles / 8 mph
up to 60 miles / 6 mph
up to 38 miles / 10 mph
up to 45 km / 25 km/h
up to 50 km / 20 km/h
up to 60 km / 16 km/h
up to 77 km / 13 km/h
up to 100 km / 10 km/h
RANGE VALUES
QUOTED ASSUME THAT
THE STANDARD SIZE
BATTERY IS FITTED
13
Weather and terrain will affect the performance. In hilly areas, or when the bike is heavily loaded, there will be a significant increase in the power used from the battery and hence the range will decrease accordingly. A lightly loaded bike will achieve higher performance levels. (These results were obtained by test riders in optimal conditions - 75kg rider, level ground, no wind).
Your BATRIBIKE bicycle has a Walk Assist Mode. This is designed to propel the bike under power at a low speed of 6 km/h (4 MPH) and is ideal to help you when pushing the bike up steep hills. It is not designed for prolonged use or whilst riding.
This feature only operates whilst the button is pressed.
Assisted Walking Mode (6 km/h)
THEN HOLD
If the assistance level is set to ZERO, then the motor will not be turned on. Your BATRIBIKE will now act and feel like a normal bicycle. This is useful when you are feeling fit at the start of a journey or using your bike for exercise purposes. Power is still only a button press away.
No Assistance - Normal Pedal Bicycle
14
Mini LCD Operation
To use under electric power, switch on by pressing and holding the POWER button on the handlebar unit until the display lights.
Switching On
To turn off the LCD and the power to the bike, press and hold the POWER button for 2 seconds.
If the power is left on for an extended period and the bike is not used, then the power will automatically be turned off.
Switching Off
Control Buttons
By means of the three buttons, UP, DOWN and MODE, on the handlebar mounted display unit, the various functions of the power controller can be utilised.
See the following sections for details.
15
Bicycle Lights
If your BATRIBIKE Electric Bicycle is supplied with lights on the front and rear, then these are switched on by pressing and holding the LIGHT button. The LCD backlight will also dim when the lights are on so as not to be too bright at night.
To turn the lights off, again press and hold the LIGHT button.
To the left of LCD is the battery meter which shows the charge remaining in the battery. The indicators will gradually go out as the battery power is used up. Refer to the table below for details.
Battery Meter
70 - 100%
SYMBOL
CHARGE REMAINING
BATTERY METER DISPLAYS THE CHARGE REMAINING IN THE BATTERY
BATTERY IS
EXHAUSTED AND
SHOULD BE
RECHARGED AS
SOON AS POSSIBLE
50 - 70%
30 - 50%
15 - 30%
0 - 15%
EMPTY
16
There are 4 levels of pedal assistance available from the motor. Using the UP and DOWN buttons you can select from Level 1 (Lowest), to Level 4 (Highest). The motor will then be activated upon pedalling.
Pedal Assistance
Please remember that the above values are provided as a guide. Due to manufacturing tolerances the performance may vary.
PEDAL ASSISTANCE FROM THE MOTOR
LEVEL / RANGE
Provides maximum power when negotiating hills and head winds.
Great when needing to simply get from A to B as fast as possible.
Great for commuting to work.
EXAMPLE OF USAGE
Normal Use Mode.
These are the levels to use for everyday cycling. Gives good performance whilst maximising usable range per charge.
Best for Leisure Use.
Use these lower power levels when negotiating busy cycle paths and crowded areas. Also use when setting off and gradually increase through the levels for a smoother performance.
Ideal for negotiating obstacles.
up to 28 miles
up to 35 miles
up to 60 miles
up to 45 miles
up to 45 km
up to 55 km
up to 70 km
up to 100 km
Full Power
75% Power
50% Power
25% Power
RANGE VALUES
QUOTED ASSUME THAT
THE STANDARD SIZE
BATTERY IS FITTED
17
Weather and terrain will affect the performance. In hilly areas, or when the bike is heavily loaded, there will be a significant increase in the power used from the battery and hence the range will decrease accordingly. A lightly loaded bike will achieve higher performance levels. (These results were obtained by test riders in optimal conditions ­75kg rider, level ground, no wind).
Your BATRIBIKE bicycle has a Walk Assist feature which utilises a twist grip throttle. This is designed to propel the bike under power at a low speed of 6 km/h (4 MPH) and is ideal to help you when pushing the bike up steep hills.
It is also designed to be used to control the power whilst pedalling right up to the maximum of 15 mph, regardless of the level selected. If the rider is not pedalling this will only work up to 4 mph.
Throttle Mode - Assisted Walking (6 km/h)
If the assistance level is set to ZERO, then the motor will not be turned on. Your BATRIBIKE will now act and feel like a normal bicycle. This is useful when you are feeling fit at the start of a journey or using your bike for exercise purposes. Power is still only a button press away.
No Assistance - Normal Pedal Bicycle
BS EN15194 Compliance
The Throttle Operation conforms to BS EN15194.
DECREASE
INCREASE
T
W
I
S
T
18
CYCLE COMPUTER
The BATRIBIKE mini LCD has useful Cycle Computer functions built in.
When first turned on the display shows the Speed in the top of the display, and the Total Distance (ODO) in the lower part.
The assistance level is set to the lowest level (1) at initial power on.
Initial Display (SPEED and ODO)
To change the display to show the Trip Distance, simply press the MODE button. Repeat to return to the ODO display.
Trip Distance
19
To reset the Trip Distance at the start of a journey simply press and hold the MODE button until the Trip display resets to zero.
Resetting the Trip
The Odometer distance displays the total distance travelled by the bicycle since leaving the factory and cannot be reset.
The display can be changed to show distances and speeds in Miles or Kilometres. To change simply press and hold the DOWN button for 10 seconds. Repeat to change the units back again.
Setting Distance Units (Miles or Km)
20
TOGETHER
When you change the display the tyre size will need to be set to suit the tyre circumference. This will ensure that the speed and distance readouts are as accurate as possible.
Setting Wheel Size (Circumference)
Value needs to be set according to the chart opposite.
OR
Set first digit
Set second digit
Set third digit
Confirm to return to normal display
Values can range from L150 to L250
21
Start with the valve at the bottom.
Roll the wheel along the ground and
measure the distance when the valve
returns to the bottom again.
CIRCUMFERENCE VALUE (in cm)
Measuring the Circumference
If you have a non-standard tyre fitment you can determine the value to use by measuring the circumference as follows:-
Circumference Settings for BATRIBIKE Models
with Standard Tyres fitted
OMEGA
TYRE SIZE (Inches)
STANDARD TYRE DESCRIPTION
VALUE
ALPHA
26 x 2.10
Schwalbe 54-559 Smart Sam Sport
L204
QUINTESSENTIAL
29 x 2.25
Schwalbe 57-622 Rapid Rob
L230
DELTA
26 x 1.75
Schwalbe 47-559 Road Cruiser PP
L200
PERDU
28 x 1.60
Schwalbe 42-622 Road Cruiser PP
L220
SIGMA
28 x 1.60
Schwalbe 42-622 Road Cruiser PP
L220
MODEL
20 x 2.00
Schwalbe 50-406 Big Apple
L150
22
Centre LCD Operation
To use under electric power, switch on at the battery if required, (bike model specific), then press and hold the POWER button on the handlebar unit until the display lights.
Switching On
To turn off the LCD and the power to the bike, press and hold the POWER button for 2 seconds.
If the power is left on for an extended period and the bike is not used, then the power will automatically be turned off.
To fully turn off the power, switch off at the battery if required, (bike model specific).
Switching Off
Control Buttons
By means of the three buttons, UP, DOWN and MODE, on the handlebar mounted display unit, the various functions of the power controller can be utilised.
See the following sections for details.
23
Bicycle Lights
If your BATRIBIKE Electric Bicycle is supplied with lights on the front and rear, then these are switched on by pressing and holding the LIGHT button. The LCD backlight will also dim when the lights are on so as not to be too bright at night.
When the lights are ON the LIGHT symbol will be displayed.
To turn the lights off, again press and hold the LIGHT button.
To the left of LCD is the battery meter which shows the charge remaining in the battery. The indicators will gradually go out as the battery power is used up. Refer to the table below for details.
Battery Meter
85 - 100%
SYMBOL and CHARGE REMAINING
BATTERY METER DISPLAYS THE CHARGE REMAINING IN THE BATTERY
BATTERY IS
EXHAUSTED AND
SHOULD BE
RECHARGED AS
SOON AS POSSIBLE
70 - 85%
55 - 70%
40 - 55%
0 - 15%
EMPTY
25 - 40%
15 - 25%
OR
24
There are 5 levels of pedal assistance available from the motor. Using the UP and DOWN buttons you can select from Level 1 (Lowest), to Level 5 (Highest). The motor will then be activated upon pedalling.
Pedal Assistance
Please remember that the above values are provided as a guide. Due to manufacturing tolerances the performance may vary.
PEDAL ASSISTANCE FROM THE MOTOR
RANGE / SPEED
Provides maximum power when negotiating hills and head winds.
Great when needing to simply get from A to B as fast as possible.
Great for commuting to work.
EXAMPLE OF USAGE
Normal Use Mode.
These are the levels to use for everyday cycling. Gives good performance whilst maximising usable range per charge.
Best for Leisure Use.
Use these lower power levels when negotiating busy cycle paths and crowded areas. Also use when setting off and gradually increase through the levels for a smoother performance.
Ideal for negotiating obstacles.
up to 28 miles / 15 mph
up to 32 miles / 12 mph
up to 45 km / 25 km/h
up to 50 km / 20 km/h
RANGE VALUES
QUOTED ASSUME THAT
THE STANDARD SIZE
BATTERY IS FITTED
up to 48 miles / 8 mph
up to 38 miles / 10 mph
up to 60 km / 16 km/h
up to 77 km / 13 km/h
up to 60 miles / 6 mph
up to 100 km / 10 km/h
25
Weather and terrain will affect the performance. In hilly areas, or when the bike is heavily loaded, there will be a significant increase in the power used from the battery and hence the range will decrease accordingly. A lightly loaded bike will achieve higher performance levels. (These results were obtained by test riders in optimal conditions ­75kg rider, level ground, no wind).
Your BATRIBIKE bicycle has a Walk Assist feature which utilises a twist grip throttle. This is designed to propel the bike under power at a low speed of 6 km/h (4 MPH) and is ideal to help you when pushing the bike up steep hills.
It is also designed to be used to control the power whilst pedalling right up to the maximum of 15 mph, regardless of the level selected. If the rider is not pedalling this will only work up to 4 mph.
Throttle Mode - Assisted Walking (6 km/h)
If the assistance level is set to ZERO, then the motor will not be turned on. Your BATRIBIKE will now act and feel like a normal bicycle. This is useful when you are feeling fit at the start of a journey or using your bike for exercise purposes. Power is still only a button press away.
No Assistance - Normal Pedal Bicycle
BS EN15194 Compliance
The Throttle Operation conforms to BS EN15194.
DECREASE
INCREASE
T
W
I
S
T
26
CYCLE COMPUTER
The BATRIBIKE Centre LCD has useful Cycle Computer functions built in.
Within a couple of seconds it then shows the Speed in the lower part of the display, and the Trip Distance in the upper part.
The assistance level is set to the lowest level (1) at initial power on.
Initial Display (SPEED and TRIP DISTANCE)
When first turned on the display briefly shows the current value of the Wheel Size Setting. (See page 29 for details).
27
To change the display to show the Total Distance, simply press the MODE button. Repeat to return to the Trip Distance display.
Trip Distance
To reset the Trip Distance at the start of a journey simply press and hold the MODE button until the Trip display resets to zero.
Resetting the Trip
The Odometer distance displays the total distance travelled by the bicycle since leaving the factory and cannot be reset.
28
When you change the display the tyre size will need to be set to suit the tyre circumference. This will ensure that the speed and distance readouts are as accurate as possible.
Setting Wheel Size (Circumference)
The display can be changed to show distances and speeds in Miles or Kilometres. To change simply press and hold the UP button for 10 seconds. Repeat to change the units back again.
Setting Distance Units (Miles or Km)
Press and hold the MODE button for 10 seconds to display the currently set value.
29
Value needs to be set according to the chart overleaf.
OR
Set first digit
Set second digit
Set third digit
Confirm to return to normal display
To change the value, press the MODE button once more to set the first digit.
Set fourth digit
Enter Setting Mode
Use UP and DOWN
buttons to change value
30
Start with the valve at the bottom.
Roll the wheel along the ground and
measure the distance when the valve
returns to the bottom again.
CIRCUMFERENCE VALUE (in mm)
Measuring the Circumference
If you have a non-standard tyre fitment you can determine the value to use by measuring the circumference as follows:-
Circumference Settings for BATRIBIKE Models
with Standard Tyres fitted
OMEGA
TYRE SIZE (Inches)
STANDARD TYRE DESCRIPTION
VALUE
ALPHA
26 x 2.10
Schwalbe 54-559 Smart Sam Sport
2040
QUINTESSENTIAL
29 x 2.25
Schwalbe 57-622 Rapid Rob
2300
DELTA
26 x 1.75
Schwalbe 47-559 Road Cruiser PP
2000
PERDU
28 x 1.60
Schwalbe 42-622 Road Cruiser PP
2200
SIGMA
28 x 1.60
Schwalbe 42-622 Road Cruiser PP
2200
MODEL
20 x 2.00
Schwalbe 50-406 Big Apple
1500
31
TROUBLESHOOTING
All display types can also show diagnostic information in the event of a malfunction.
LED style display
If an error occurs the LED display will show a code by flashing the first battery light. Make a note of the number of flashes and turn off the bicycle power at both the LCD and the battery switch. After 2 minutes turn on the power again. If the code re-occurs contact your dealer for assistance.
Diagnostic Error Messages
First Light Flashes
Number of
Flashes
Error Type
Action
Required
2
Motor Error
Check Motor Plug, if all OK contact Dealer for Assistance
3
Controller Error
Contact Dealer for Assistance
4
Display Error
5
Brake Sensor Error
8
Low Battery Voltage
Charge the Battery
Contact Dealer for Assistance
Check brake lever returns fully, if all OK contact Dealer for Assistance
32
Error Number Shown
Mini LCD style display
If an error occurs the Mini LCD display will show a code as in the example shown. Make a note of the error number and turn off the bicycle power at both the LCD and the battery switch. After 2 minutes turn on the power again. If the code re-occurs contact your dealer for assistance.
Error No.
Error Type
Error Type
E02
Motor Error
Check Motor Plug, if all OK contact Dealer for Assistance
E03
Controller Error
Check throttle returns correctly, if all OK contact Dealer for Assistance
E04
Throttle Error
E05
Brake Sensor Error
E08
Low Battery Voltage
E09
Battery Error
Contact Dealer for Assistance
Charge the Battery
Contact Dealer for Assistance
Check brake lever returns fully, if all OK contact Dealer for Assistance
33
Centre LCD style display
If an error occurs the Centre LCD display will show a code as in the example shown. Make a note of the error number and turn off the bicycle power at both the LCD and the battery switch. After 2 minutes turn on the power again. If the code re-occurs contact your dealer for assistance.
Error No.
Error Type
Error Type
2
Power Consumption Error
Contact Dealer for Assistance
3
Controller Error
Check throttle returns correctly, if all OK contact Dealer for Assistance
4
Throttle Error
5
Brake Sensor Error
8
Low Battery Voltage
9
Battery Error
Contact Dealer for Assistance
Charge the Battery
Contact Dealer for Assistance
Check brake lever returns fully, if all OK contact Dealer for Assistance
34
WARRANTY CONDITIONS
The following warranty conditions are in addition to your legal rights and apply to Display Options when FITTED BY AUTHORISED BATRIBIKE DEALERS only.
Requirements for Warranty
As the makers, we guarantee against possible material or construction defects. Provided the following conditions are satisfied :
Please retain your receipt as this is your proof of purchase and entitlement to Warranty. The guarantee starts on the date of original purchase.
Your new Display Option is guaranteed for 2 years from date of fitting by an Authorised BATRIBIKE Dealer.
Exclusions from Warranty
When the bicycle is used negligently or suffers accidental damage.
Damage ascribed to normal wear and tear.
Poor maintenance, or modifications that no longer comply with
regulations or original technical specifications.
Damage due to external causes.
The bicycle is put up for hire.
Compensatory costs arising from damages or accidents.
Cost incurred by loss of the bicycle’s usage.
WARRANTY
YEAR
O
P
T
I
O
N
A
L
D
I
S
P
L
A
Y
S
2
35
In the event of a Warranty claim
In the event of warranty repairs becoming necessary you should return your bicycle to your Authorised Batribike Dealer, (where you originally purchased your Batribike).
Original defective parts that are sent to the manufacturer for assessment will be replaced by the same or equal value part.
Delivery and collection charges are not included. These are borne by the owner.
Fallowgate Limited exclusively makes the decision whether or not the warranty applies.
----- UPGRADES - DISPLAY OPTIONS - ISSUE 2 - ©2018 Batribike Limited -----
Batribike Limited Unit 4, Ingleby Grange Ingleby Lincoln LN1 2PQ
Phone: 01427 787774 E-mail: support@batribike.com
www.batribike.com
BATRIBIKE are Members of the Bicycle Association of Great Britain
Loading...