Network information ................................................................................................................................................. 19
Management system ................................................................................................................................................20
New apartment........................................................................................................................................................... 24
Common settings....................................................................................................................................................... 26
Open lock...................................................................................................................................................................... 27
Server manage access ............................................................................................................................................. 28
New identifier .............................................................................................................................................................. 28
New restriction ........................................................................................................................................................... 30
New forward queue .................................................................................................................................................. 33
Working principle ......................................................................................................................................................49
Mobile access with UKEY applicationhttps://wiki.bas-ip.com/basipidapp ........................................ 49
Triple-clicking setup with UKEY Cfghttps://wiki.bas-ip.com/display/BASIPCONFIGID/
The "2" button moves the cursor up, the "8" button moves the cursor down. To confirm the
values, press the "#" button and the "*" button to go back.
Mode: select operation mode of the panel.
Configuration through graphical interface– 12
Information about operation modes
If you select the "Wall" mode, you must enter 4 digits of the building number, 2 digits of
the unit number, 2 digits of the floor number, and 2 digits of the apartment number to
call the desired monitor.
If you select the "Unit" mode, youmust enter only 2 digits of the floor number and2
digits of the apartment number to call the desired monitor.
You shouldn't select individual opreration mode for these panels. It is used only for
individual panels.
Language: Select interface language.
Building: Number of the building.
Unit:Unit number.
Index:Device number of the outdoor panel.
Password: System password to enter settings or WEB interface.
Volume: Loudspeaker volume of the outdoor panel.
Size:Select the camera stream resolution of the outdoor panel.
The number of the building and the unit should correspond to values of the internal
monitor that willreceive an incoming call from the outdoor panel. If you have several
outdoor panels with the same logical address, then in the Index field you should specify
values 2, 3, 4, 5 etc., up to 9. If the logical addressing of the outdoor panel corresponds
to the address of the monitor, and the IP addresses of the devices are in the same
network segment, the devices will find each other and the call will be correct.
Network settings
Main network settings are configured in this tab.
Configuration through graphical interface– 13
DHCP: Enable/disable mode to get network settings automatically.
IP: IP address ofoutdoor panel.
By default the outdoor panel can have a static IP address 192.168.68.90 or 192.168.1.90.
Mask: Subnet mask.
Gateway: Default gateway.
DNS: Address of the DNS server.
Server:IP address of your PC or server, where Management Software or Link software is
installed.
Access settings
When you switch to Access settings menu, the following interface will be displayed:
Configuration through graphical interface– 14
Timeout: Time when contacts of the panel relay will be closed or open.
Delay: Time after which contacts of the panel relay will be closed or open (delay before
unlocking).
Elev Refer: Floor number where the panel is installed (using elevator control module EVRC-IP,
optional).
Password: Password to open the lock by entering the unlocking code on the panel keypad. To
enter the password input mode, press the "#" key, type the password and press "#" again.
Access pasword could be from 1 to8 digits
Additional settings
When you switch to Additional settings, the following interface will be displayed:
Configuration through graphical interface– 15
RoomNum: Apartment number to which access card must be linked.
Adding cards through graphical interface:
Enter the desired apartment number and wave the card in front of the area of the
reader. A signal will sound from the panel, confirming that the card is registered, and a
card number will be displayed in theCard field.
Reboot:Restart outdoor panel. To restart outdoor panel, it is necessary to enter"#", press"1",
and then press "#" again.
Default: Reset panel settings to factory settings. To reset outdoor panel, it is necessary to
enter"#", press"1", and then press"#"again.
Note that all cards will be removed from the panel memory when it is factory reset.
About system
After switching to About system menu, the following interface will be displayed:
Configuration through graphical interface– 16
This window displays the current status of the SIP connection, the current IP address, the MAC
address, and the current firmware version.
Loading...
+ 37 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.