195 Plus - 220 Plus - 250 Plus -
275 Plus - 300 Plus
174196-174221-174251-174276-174301
Bartscher GmbH
Franz-Kleine-Str. 28
D-33154 Salzkotten
Germany
Phone: +49 5258 971-0
Fax: +49 5258 971-120
Technical Support Hotline: +49 5258 971-197
www.bartscher.com
Version: 4.0
Date of preparation: 2023-10-25
EN
2
Original instruction manual
1 Safety ............................................................................................................ 2
1.1 Explanation of Signal Words .................................................................... 2
1.2 Safety instructions.................................................................................... 3
1.3 Intended Use ........................................................................................... 5
1.4 Unintended Use ....................................................................................... 5
2 General information ....................................................................................... 6
2.1 Liability and Warranty .............................................................................. 6
2.2 Copyright Protection ................................................................................ 6
2.3 Declaration of Conformity ........................................................................ 6
3 Transport, Packaging and Storage ................................................................ 7
3.1 Delivery Check ......................................................................................... 7
3.2 Packaging ................................................................................................ 7
3.3 Storage .................................................................................................... 7
4 Technical Data ............................................................................................... 8
4.1 Technical Specifications .......................................................................... 8
4.2 List of Components of the Appliance ..................................................... 11
4.3 Functions of the Appliance ..................................................................... 13
4.4 Protective Elements of the Appliance .................................................... 14
5 Installation and operation ............................................................................ 16
5.1 Installation .............................................................................................. 16
5.2 Operation ............................................................................................... 17
6 Cleaning and Maintenance .......................................................................... 22
6.1 Safety Instructions for Cleaning ............................................................. 22
6.2 Cleaning ................................................................................................. 23
6.3 Maintenance .......................................................................................... 26
7 Possible Malfunctions .................................................................................. 27
8 Disposal ....................................................................................................... 28
174196 1 / 28
Safety
EN
Read this instruction manual before using and keep it available
at all times!
DANGER!
The signal word DANGER warns against hazards that lead to severe
injuries or death if the hazards are not avoided.
WARNING!
The signal word WARNING warns against hazards that may lead to
moderate or severe injuries or death if the hazards are not avoided.
Diese Bedienungsanleitung beschreibt di e Installation, Bedienung und Wartung d es Geräts und gilt als wichtige Infor mationsquelle und Nachschlagewer k. Die Kenntnis aller enthaltenen Sicherh eitshinweise und Handlungsanweisu ngen schafft die Voraussetzung f ür das sichere und sachgerechte Ar beiten mit dem Gerät. Darüber hinaus müssen die für den Einsatzbereic h des Geräts geltenden örtlichen Unfall verhütungsvorschriften und allgemeine n Sicherheitsbestimmungen eingehalten werden. Diese Bedienungsanleitung is t Bestandteil des Produkts und muss in unmittelbarer Nähe des Geräts für das In¬stallations-, Bedienu ngs-, Wartungs- und Reinigungspers onal jederzeit zugänglich auf¬bewahrt werd en. Wenn das Gerät an eine dritt e Person
weitergegeben wird, muss die Bedienungsa nleitung mit ausgehändigt werden.
This instruction manual contains information about installation, operation and
maintenance of the appliance and constitutes an important source of information
and reference guide. The knowledge of all operational and safety instructions
included in this manual is a prerequisite for safe and proper handling of the
appliance. Additionally, accident prevention, occupational health and safety, and
legal regulations in force in the area the appliance is used apply.
Before you start using the appliance, especially before turning it on, read this
instruction manual in order to avoid personal injuries and property damages.
Improper use may cause damage.
This instruction manual forms and integral part of the product and must be stored in
an immediate vicinity of the appliance and be available at all times. The instruction
manual should be transferred together with the appliance.
1 Safety
This appliance has been manufactured in accordance with technical standards
currently in force. However, the appliance may be a source of hazards if used
improperly or contrary to its intended purpose. All persons using the appliance must
consider information included in this instruction manual and observe safety
instructions.
1.1 Explanation of Signal Words
Important safety instructions and warning information are indicated in this
instruction manual with appropriate signal words. You must strictly follow the
instructions, to prevent accidents, personal injuries and property damages.
2 / 28 174196
Safety
EN
CAUTION!
The signal word CAUTION warns against hazards that may lead to
light or moderate injuries if the hazards are not avoided.
IMPORTANT!
The signal word IMPORTANT indicates possible property damages,
which may occur if safety instructions are not observed.
NOTE!
The symbol NOTE indicates subsequent information and guidelines
for the user on usage of the appliance.
, die
1.2 Safety instructions
Electrical Current
• Too high a mains voltage or incorrect installation may cause electric shock.
• The appliance may be connected only if data on the rating plate correspond with
the mains voltage.
• To avoid short-circuit, the appliance should be kept dry.
• If there are malfunctions during operation, disconnect the appliance from the
power supply.
• Do not touch the appliance’s plug with wet hands.
• Never take hold of the appliance if it has fallen into water. Immediately
disconnect the appliance from the power supply.
• Any repairs or housing opening may be carried out by professionals and
relevant workshops only.
• Do not transport the appliance, holding it by the power cord.
• Do not allow the power cord to come into contact with heat sources or sharp
edges.
• Do not bend, pinch nor knot the power cord.
• Always completely unwind the power cord.
• Never place the appliance or other objects on the power cord.
• Always take hold of the plug to disconnect the appliance from the power supply.
174196 3 / 28
Safety
EN
• Check the power cord regularly for damage. Do not use the appliance if the
power cord is damaged. If this cable is damaged, it must be replaced by
customer service or a qualified electrician in order to avoid dangers.
Safety During Operation of the Slicer
• Never put hands between the pusher handle and the blade or the movable slice
thickness partition until they are completely secured (slice thickness adjustment
knob set to “0” position).
• During slicing operation keep hands away from the blade in order to avoid cuts
and accidents. In order to avoid accidents, always use the pusher handle to
push the product to be sliced to the movable slice thickness partition.
• The blade is very sharp; caution is advised when checking the blade sharpness.
During operation wear cut protection gloves class 5 of DIN EN 388 standard!
• During operation, the operator should wear safety clothing that meets local
sanitary standards.
Supervised Usage only
• Only supervised appliance may be used.
• Always remain in an immediate vicinity of the appliance.
Operating Personnel
• The appliance may only be operated by qualified personnel and trained
specialist personnel.
• This appliance may not be operated by persons (including children) with limited
physical, sensory or mental capabilities, nor by persons with limited experience
and/or limited knowledge.
• Children should be supervised to ensure that they are not playing with or
switching on the appliance.
4 / 28 174196
Safety
EN
Improper Use
• Unintended or prohibited use may cause damage to the appliance.
• The appliance may only be used when its technical condition is flawless and
allows for safe operation.
• The appliance may only be used when all connections are executed according
to rules of law in force.
• The appliance may only be used when it is clean.
• Use only original spare parts. Never attempt to repair the appliance on your own.
• Do not introduce any changes in the appliance nor modify it.
1.3 Intended Use
As described below, every use of the appliance for a purpose differing and/or
diverging from its intended standard use, is prohibited and considered to be an
unintended use.
The following is an intended use:
– Slicing sausages
1.4 Unintended Use
An unintended use may lead to personal injuries or property damages caused by
hazardous voltage, fire or high temperature. The appliance may only be used to
perform tasks described in this instruction manual.
The following is an unintended use:
– Cutting of products that are not food products.
– Cutting products with bones.
– Cutting frozen products.
174196 5 / 28
General information
EN
2 General information
2.1 Liability and Warranty
All information and instructions in this instruction manual account for legal
regulations in force, current level of technical engineering knowledge as well as our
expertise and experience, developed over the years. If special models or additional
options are ordered, or state-of-the-art technical solutions were implemented, the
actual scope of delivery of the appliance may, in some circumstances, differ from
descriptions and numerous drawings in this instruction manual.
The manufacturer is not liable for any damages nor faults stemming from:
– failure to observe instructions,
– unintended use,
– technical alterations introduced by the user,
– usage of unapproved spare parts.
We reserve the right to introduce technical modifications to the product, intended for
improvement of the appliance and its performance.
2.2 Copyright Protection
This instruction manual, and texts, drawings and images included in it, as well as its
other components are copyright protected. It is prohibited to reproduce this
instruction manual (including its excerpts), in any form and by any means, and to
use and/or transfer its content to third parties without manufacturer’s written
permission. Violation of the above results in obligation to pay compensation. We
reserve the right to claim further damages.
2.3 Declaration of Conformity
The appliance meets the currently applicable standards and guidelines of the
European Union. We confirm the above in the EC Declaration of Conformity. We
may provide relevant Declaration of Conformity upon request.
6 / 28 174196
Transport, Packaging and Storage
EN
3 Transport, Packaging and Storage
3.1 Delivery Check
Immediately upon reception, check the delivery for completeness and possible
shipping damage. In the case of visible transport damage refuse to accept the
appliance or accept it conditionally. Mark and note the scope of damage in shipping
documents/consignment list of the shipping company and lodge a complaint.
Concealed damage must be reported immediately upon its discovery, as
compensation claims may only be filed within applicable time limits.
If you find that parts or accessories missing, please contact our Customer Service
Department.
3.2 Packaging
Do not dispose of the appliance cardboard box. It may be used to store the
appliance when relocating or when shipping the appliance to our service point in the
case of any damages.
The packaging and its elements are made of recyclable materials. Particularly,
these are: plastic films and bags, cardboard box.
When disposing of the packaging, observe applicable domestic regulations.
Recyclable packaging materials should be recycled.
3.3 Storage
Leave the packaging closed until installation of the appliance; observe external
indications concerning method of placing and storage. Store the packaging in the
following conditions only:
– in closed rooms;
– in dry and dust-free surrounding;
– away from aggressive agents;
– in a location protected against sunlight;
– in a location protected against mechanical shocks.
In the case of extended storage (over three months), make sure you check the
condition of the packaging and the parts regularly. If needed, replace the packaging
with a new one.
174196 7 / 28
Technical Data
EN
Name:
Slicing machine 195 Plus
Art. No.:
174196
Material:
aluminium, plexiglas, plastic
Blade diameter, in mm:
195
Maximum rotational speed, in RPMs:
277
Slicing thickness range, in mm:
1 - 12
Slicing length, in mm:
185
Slicing height, in mm:
130
Degree of protection:
IPX3
Connected load:
0,11 kW | 230 V | 50 Hz
Dimensions (W x D x H), in mm:
335 x 440 x 340
Power cord length, in mm:
1,4
Weight, in kg:
11,2
4 Technical Data
Version / Characteristics
• Oblique cutter / gravity slice
• Carriage: removable (except art. No. 174196), 2 handles
• Designed for: sausages
• Pusher
• Slice guide
• Sharpener
• Blade guard: double
• Magnetic switch
• Control: button
• ON/OFF switch
• Indicator light: ready for operation
4.1 Technical Specifications
8 / 28 174196
Technical Data
EN
Name:
Slicing machine 220 Plus
Art. No.:
174221
Material:
aluminium, plexiglas, plastic
Blade diameter, in mm:
220
Maximum rotational speed, in RPMs:
191
Slicing thickness range, in mm:
1 - 12
Slicing length, in mm:
205
Slicing height, in mm:
135
Degree of protection:
IPX3
Connected load:
0,13 kW | 230 V | 50 Hz
Dimensions (W x D x H), in mm:
410 x 475 x 360
Power cord length, in mm:
1,4
Weight, in kg:
14,0
Name:
Slicing machine 250 Plus
Art. No.:
174251
Material:
aluminium, plexiglas, plastic
Blade diameter, in mm:
250
Maximum rotational speed, in RPMs:
190
Slicing thickness range, in mm:
1 - 12
Slicing length, in mm:
195
Slicing height, in mm:
140
Degree of protection:
IPX3
Connected load:
0,13 kW | 230 V | 50 Hz
Dimensions (W x D x H), in mm:
435 x 510 x 385
Power cord length, in mm:
1,4
Weight, in kg:
14,8
174196 9 / 28
Technical Data
EN
Name:
Slicing machine 275 Plus
Art. No.:
174276
Material:
aluminium, plexiglas, plastic
Blade diameter, in mm:
275
Maximum rotational speed, in RPMs:
190
Slicing thickness range, in mm:
1 - 12
Slicing length, in mm:
180
Slicing height, in mm:
150
Degree of protection:
IPX3
Connected load:
0,13 kW | 230 V | 50 Hz
Dimensions (W x D x H), in mm:
435 x 520 x 385
Power cord length, in mm:
1,4
Weight, in kg:
16,9
Name:
Slicing machine 300 Plus
Art. No.:
174301
Material:
aluminium, plexiglas, plastic
Blade diameter, in mm:
300
Maximum rotational speed, in RPMs:
186
Slicing thickness range, in mm:
1 - 15
Slicing length, in mm:
230
Slicing height, in mm:
175
Degree of protection:
IPX3
Connected load:
0,2 kW | 230 V | 50 Hz
Dimensions (W x D x H), in mm:
480 x 630 x 461
Power cord length, in mm:
1,4
Weight, in kg:
20,8
10 / 28 174196
Technical Data
EN
Fig. 1
4.2 List of Components of the Appliance
174196 11 / 28
Technical Data
EN
1. Blade
2. Blade protective ring
3. Blade guard
4. Pusher handle with pusher
5. Food tray
6. Carriage
7. Carriage lock knob (except for
model No. 195 Plus, art. No.
174196)
8. Slice thickness adjustment knob
9. ON/OFF switch with indicator light
10. Feet (4 pcs)
11. Handle with hand protection
12. Slice tray
13. Movable slice thickness partition
14. Pusher handle guard
15. Sharpener
16. Slice guide
17. Sharpener retaining screw
18. Blade guard retaining screw
19. Power cord
20. Blade protection device
Basic blade
Material: high-alloy steel
Application: sausages
Compatible model:
195 Plus
220 Plus
250 Plus
275 Plus
300 Plus
Diameter (mm):
195
220
250
275
300
Dimensions (mm):
W 195
D 195
H 15
W 220
D 220
H 16
W 250
D 250
H 18.2
W 275
D 275
H 22
W 300
D 300
H 21
Weight (kg):
0,69
0,79
0,98
1,5
1,6
Art. No.:
174060
174061
174062
174063
174064
Description for Fig. 1
Accessories (included in the scope of delivery!)
12 / 28 174196
Technical Data
EN
Blade with corrugated cutting edge
Material: steel, hard chrome-plated
Compatible model:
195 Plus
220 Plus
250 Plus
275 Plus
300 Plus
Diameter (mm):
195
220
250
275
300
Dimensions (mm):
W 195
D 195
H 13
W 220
D 220
H 15
W 250
D 250
H 18
W 275
D 275
H 22
W 300
D 300
H 23
Weight (kg):
0,64
0,67
1,17
1,47
2,13
Art. No.:
174050
174052
174054
174056
174058
Blade, non-stick coating
Material: stainless steel, Teflon-coated
Compatible model:
195 Plus
220 Plus
250 Plus
275 Plus
300 Plus
Diameter (mm):
195
220
250
275
300
Dimensions (mm):
W 195
D 195
H 13
W 220
D 220
H 15
W 250
D 250
H 18
W 275
D 275
H 22
W 300
D 300
H 23
Weight (kg):
0,64
0,67
1,17
1,47
2,13
Art. No.:
174051
174053
174055
174057
174059
Zu
Accessories (not included in the delivery!)
4.3 Functions of the Appliance
With this slicing machine you can quickly cut sausages into slices of various
thicknesses.
174196 13 / 28
Technical Data
EN
3
Blade guard
4
Pusher handle with pusher
9
ON/OFF switch
(after a power failure, the appliance can
only be switched on again by pressing the
white START button in the appliance
ON/OFF switch)
14
Pusher handle with grip and hand
protection (11)
Carriage locking device (Fig. 3).
(Models 174221, 175251, 174276,
174301; model 174196 — non-removable
carriage)
The carriage can only be removed for
cleaning when the slice thickness
adjustment knob is undone beyond the
zero setting and the carriage is pulled
towards the slice thickness adjustment
knob:
– In doing so, the carriage lock knob
must be loosened. If it cannot be
completely loosened, pull the carriage
again in the direction of the carriage
lock knob until the safety device
audibly engages.
– Fully loosen the carriage lock knob and
remove the carriage from the appliance
by pulling it upwards.
Fig. 2
Fig. 3
4.4 Protective Elements of the Appliance
14 / 28 174196
Technical Data
EN
15
Sharpener serving as the upper
blade guard
There is a magnetic connector (a) on the
sharpening tool: the appliance operates
only when the sharpener is properly
positioned.
When the sharpener is removed during
operation the appliance stops. Once the
sharpener is properly repositioned the
appliance does not start automatically but
it needs to be switched on again with the
white START button in the ON/OFF switch
(B, Fig. 7).
Fig. 4
Residual Risks
Despite all mechanical and electrical protective means the appliance is equipped
with according to the regulations (both in the operational phase and during cleaning
and maintenance), residual risks exist that cannot be completely precluded. In this
instruction manual they are indicated by the warning word WARNING. Observe also
warning indications on warning stickers placed on the appliance.
Residual risks (e.g., danger of injury) may be present also when slicing smaller
pieces or pushing residues. To this end, the appliance is equipped with the pusher
handle with pusher.
After disassembly of the appliance for cleaning, pay particular attention to the blade,
as with the sharpener removed, part of the blade is exposed.
174196 15 / 28
Installation and operation
EN
CAUTION!
Choking hazard!
Prevent children from accessing package materials, for instance: plastic
bags and EPS.
5 Installation and operation
5.1 Installation
Unpacking / Positioning
• Unpack the appliance, remove all external and internal packaging elements and
shipment safeguards.
• If the appliance is covered with a protective film, remove it. Remove the film
slowly, so no glue residues are left. Remove any glue residues with the use of a
suitable solvent.
• Be careful not to damage the rating plate and warning labels fixed on the
appliance.
• Never place the appliance in humid or wet environment.
• Place the appliance in a way making the connections easily accessible, so that
they may be quickly disconnected if such a need arises.
• The appliance should be placed on surfaces that are:
– even, with sufficient bearing capacity, resistant to water, dry and resistant
to high temperatures;
– sufficiently large, and thus enabling usage of the appliance with no
problems;
– easily accessible;
– well ventilated.
• Maintain sufficient clearance from table edges. The appliance might turn over
and fall down.
• When selecting the place to set the appliance in, consider the dimensions of the
appliance (section 'Technical Specification'). Provide enough space to securely
operate the appliance.
• Operation location must be well lit.
• Put the slicing machine in such a way that the person operating it could stand
straight and stable in front of the appliance. The operator has to be able to
constantly see the ON/OFF switch and the slice thickness adjustment knob.
16 / 28 174196
Installation and operation
EN
2. Fit the enclosed slice guide (16).
3. To this end, loosen the lower screw (f) of the
previously installed blade protection device (20)
on the rear of the appliance with a suitable
screwdriver.
4. Attach the slice guide (16) to the blade
protection device (20) using the loosened screw
(f).
Fig. 5
To securely use the slicing machine, keep at least 20 cm clearance from the slicing
machine and walls, objects, cupboards, etc.
• The clearance from the floor should be approx. 80 cm.
• Place the appliance in a room, in which temperature ranges from +5°C do +32
°C, and the maximum moisture level should be 70%.
Power supply connection
• Verify if technical data of the appliance (see rating plate) correspond with the
local electric power grid specification.
• Connect the appliance to a single, properly grounded mains socket with
protective contact. Do not connect the appliance to a multi-socket.
• The power cord should be laid in a way preventing anyone from threading on it
or tripping against it.
5.2 Operation
Before First Use
1. Thoroughly clean the appliance and equipment before first use observing
instructions in section 6 'Cleaning and Maintenance'.
174196 17 / 28
Installation and operation
EN
– whether the appliance is connected to a
grounded single socket.
– whether the carriage (6) is firmly
connected to the carriage lock knob (7).
– the movement of the carriage (6) and
that no obstacle is blocking and no
object is on the carriage tray (5).
– lifting and lowering of the pusher
handle (4) without any obstacles during
its movement.
– hole of the cut thickness movable
partition (13) with the slice thickness
adjustment knob (8), rotating it
clockwise and counter-clockwise.
– whether the sharpener (15) is correctly
mounted and that there is the possibility
of removing it without any problems.
Fig. 6
Fig. 7
Check before starting the appliance:
ON/OFF Switch
18 / 28 174196
Installation and operation
EN
Correct stance
Incorrect stance
Fig. 8
Appliance Operation (Fig. 6, 7)
1. Plug the appliance into a suitable single socket.
2. To switch the appliance on, press the white START button (B) in the appliance
ON/OFF switch (9).
The indicator lamp (C) lights up and remains lit during operation.
3. Leave the appliance on for 2–3 minutes in order to make sure it operates
correctly (without slicing products).
4. Switch the appliance off with the black STOP button (A) in the appliance
ON/OFF switch (9).
5. Set the slice thickness adjustment knob (8) in '0' position.
6. Lift the pusher handle (4) and place the cut goods on the carriage tray (5) so
that they are between the movable slice thickness partition (13) and the pusher
handle with the pusher (4).
WARNING!
In order to avoid accidents, always use the pusher handle (4) to push the
product to be sliced to the movable slice thickness partition (13)!
7. Adjust slice thickness: rotate the slice thickness adjustment knob (8) counterclockwise until it reaches the desired position.
8. Assume correct stance at the slicing machine (Fig. 8). Put right hand on the
pusher handle, left next to the slice tray so as not to touch the blade; the body
must be straight and vertical towards the worktop.
WARNING!
Risk of injury through contact with the blade!
Never assume a stance with hands, fingers or other parts of the body that might
come into contact with the blade!
9. Switch the appliance on with the white START button (B) in the appliance
ON/OFF switch (9).
174196 19 / 28
Installation and operation
EN
10. Move the carriage (6) slowly and steadily towards the blade (1) using the pusher
handle (4).
11. The best slicing results are obtained when the pusher handle (4) is slightly
pushed towards the movable slice thickness partition (13).
The product to be sliced encounters the blade (1), the sliced product is separated
and falls onto the tray (12), which is located on the back of the movable slice
thickness adjustment partition (13).
Do not remove the pusher handle with the pusher (4) unless the food product to be
sliced is of unusual size or shape.
12. After cutting, the carriage (6) is to be put into initial position and the slice
thickness adjustment knob (8) should be set to '0' position.
13. Switch the appliance off with the black STOP button (A) in the appliance
ON/OFF switch (9). Do not allow the appliance to run idle.
14. The sliced good can be now removed from the slice tray.
WARNING!
Cut wounds hazard!
Never operate the appliance with wet or moist hands.
Never put hands between the blade (1) and the pusher handle (4) or the
movable slice thickness partition (13) until they are fully closed (slice thickness
adjustment knob (7) set to '0' position).
During operation keep hands away from the blade in order to avoid cuts and
accidents. Use the handle of the pusher (4).
WARNING!
Never use the appliance for more than 15 minutes in order to avoid motor
overheating. After a short break the appliance may be switched on again.
20 / 28 174196
Installation and operation
EN
2. Loosen the fixing screw (a) of the sharpener
(15) on the back side of the appliance (Fig. 9).
3. Remove the sharpener (15) and rotate it by
180°.
4. Put the sharpener (15) into the special guide
rail and tighten the fixing screw (a).
5. Make sure the surface of the sharpener is
close to the edge of the blade. Otherwise
correct it.
6. Connect the appliance to a grounded single
socket and switch it on with the white START
button (B).
Fig. 9
Fig. 10
Blade Sharpening
If the surface of a sliced product becomes frayed or coarse and the cutting
operations become cumbersome, the blade must be sharpened.
1. Pull the plug out from the socket and clean the blade edges before sharpening
using alcohol in order to degrease them.
7. Hold the depressed button (b, Fig. 10) of the sharpener on the back of the
sharpener (1) and leave the appliance switched on for approx. 60 seconds, until
the blade is burred.
8. Then hold the (c) button in the front and the (b) button at the back of the
sharpener simultaneously for approx. 3–4 seconds to sharpen the blade and
remove the burr. Release both buttons simultaneously.
ATTENTION!
Do not exceed the above mentioned sharpening time of 3–4 seconds so as
not to cause the so-called 'zero grind'.
9. Switch the appliance off with the black STOP button (A) in the appliance
ON/OFF switch (9).
174196 21 / 28
Cleaning and Maintenance
EN
10. Check if the blade is sharp enough.
11. Continue until the desired sharpening level is reached.
WARNING! Cut wounds hazard!
The blade is very sharp!
Be very careful when checking the sharpness of the blade!
During operation wear class 5 cut resistant protective gloves of DIN EN 388
standard!
12. After sharpening clean the blade and sharpener elements. In order to ensure it
will operate correctly, keep the sharpener in a good condition. Observe
instructions in sections 6 'Cleaning and Maintenance'.
13. Set the sharpener back to its initial position. Follow the assembly instruction in
reverse order.
ATTENTION!
In order to keep the blade in the optimum condition and maintain safety, it
should be replaced when its height is reduced by approx. 5–7 mm.
6 Cleaning and Maintenance
6.1 Safety Instructions for Cleaning
• Before cleaning, disconnect the appliance from the power supply.
• Leave the appliance to cool down completely.
• Make sure water does not enter the appliance. Do not immerse the appliance in
water or other liquids during cleaning. Do not clean the appliance with a
pressurized water jet.
• Do not use any sharp or pointed, nor metal implements (knife, fork, etc.). Sharp
or pointed implements may damage the appliance, and when in contact with live
parts, they may cause electric shock.
• For cleaning, do not use any scouring agents that contain solvents nor corrosive
cleaning agents. They may damage the surface.
22 / 28 174196
Cleaning and Maintenance
EN
CAUTION!
During maintenance works and cleaning (when the protective elements
are removed) check for any possible hazards.
Unplug the appliance from a socket.
Ensure that the slice thickness adjustment knob is in '0' position.
Move the carriage towards the slice thickness adjustment knob.
ATTENTION!
Never wash removable elements in a dish-washer.
Fig. 11
6.2 Cleaning
1. At the end of each working day, and more frequently if needed, thoroughly clean
all parts of the appliance that come into contact with food products.
2. Carry out the cleaning of the individual groups observing the instructions below.
Carriage and Pusher Handle
1. To clean, remove the carriage (6) from the appliance.
NOTE!
The carriage can only be removed when the slice thickness adjustment
knob is undone beyond the zero setting and the carriage is pulled towards
the slice thickness adjustment knob.
2. In doing so, the carriage lock knob must be loosened. If it cannot be completely
loosened, pull the carriage again in the direction of the carriage lock knob until
the safety device audibly engages.
174196 23 / 28
Cleaning and Maintenance
EN
1. Remove the sharpener from the appliance (Fig. 9).
2. In order to remove the blade guard (3) for cleaning
loosen the fixing screw (d) at the back of the
appliance (Fig. 12) and push it towards the blade
guard (3).
3. Remove the blade guard (3) from the appliance.
Fig. 12
4. To remove the blade (1) undo 3 locking screws
(e) using a suitable screwdriver (Fig. 13).
5. Carefully detach the blade (1).
6. Clean the blade guard (3) and blade (1) in
warm water and a neutral cleaning agent. Use a
sponge, suitable cleaning brush or soft cloth.
Rinse in fresh water.
Fig. 13
3. Fully loosen the carriage lock knob and remove the carriage from the appliance
by pulling it upwards.
ATTENTION!
The 195 Plus model / art. No. 174196 does not have a carriage lock knob.
The carriage of the appliance is not removable.
4. Clean the carriage (6) with guard (14), carriage tray (5) and pusher handle with
pusher (4) in warm water with a soft cloth and neutral cleaning agent.
5. Rinse with fresh water to remove remains of the cleaning agent.
6. Allow cleaned components to air dry or dry thoroughly before reassembling
them in the appliance.
Blade and Blade Cover
WARNING! Cut wounds hazard!
The blade is very sharp!
Never touch the blade edge with bare hands.
During cleaning of the blade wear class 5 cut resistant protective gloves of DIN
EN 388 standard!
24 / 28 174196
Cleaning and Maintenance
EN
Fig. 14
7. Clean the blade protection ring (2) in warm water and a neutral cleaning agent.
Rinse in fresh water. Leave the cleaned parts for drying or wipe them with a dry
cloth.
8. After cleaning install the blade (1) with the use of three adjustment screws (e) —
maintaining correct stance — and the blade guard (3) with the use of the screw
(d).
Blade Protection Device and Slice Guide (Fig. 14)
1. Loosen the lower screw (f) of the protection device (20) at the rear side of the
appliance. Remove the slice guide (16).
2. Loosen the upper screw (f) and remove the protection device (20) for cleaning.
3. Clean removed parts in warm water with a neutral cleaning agent.
4. Rinse in fresh water.
5. Thoroughly dry all cleaned elements.
174196 25 / 28
Cleaning and Maintenance
EN
Sharpener (Fig. 15)
1. Remove the complete sharpener assembly from
appliance (fig. 9).
2. After sharpening, clean the sharpener elements
(g) with a cleaning brush soaked in alcohol.
Fig. 15
1. Lubricate the carriage regularly with a foodgrade machine grease.
2. To do this, lay the slicing machine on its
side.
3. Apply some machine oil to both ends of the
carriage axle (i) (Fig. 16).
4. Move the carriage forward and backward in
order to distribute the grease evenly.
5. Remove the excess grease with a cloth.
Fig. 16
Slice Tray and Housing (Fig. 14)
1. Clean the slice tray (11) and housing with the use of a moist, soft cloth and
neutral cleaning agent.
2. Wipe it with a clean, soft cloth.
3. Dry completely after cleaning.
4. Then reattach the protection device (20) and then the slice guide (16) to the
appliance with the use of screws.
6.3 Maintenance
Regular Lubrication / Greasing
26 / 28 174196
Possible Malfunctions
EN
Problem
Possible cause
Solution
Appliance does not
work
No power
Check the electric power
supply
Damaged electrical
installation
Contact the supplier
Damaged switch
Contact the supplier
Damaged motor
Contact the supplier
The blade does not cut
or the slices are fuzzy
and/or irregular
Blade is not sharpened
Sharpen the blade (section
'Blade Sharpening')
Blade excessively worn
Replace the blade
The blade sharpening
is not satisfactory
Position is not correct
Fit the sharpener correctly
(section 5.2 'Operation')
Sharpening stones are
soiled
Clean the sharpening
stones
The carriage runs with
difficulties
Carriage axle not greased
enough
Grease the carriage axles
(section 6.3
'Maintenance')
The motor does not
work
Sharpener is not attached
properly in the holder
Check the sharpener
attachment
7 Possible Malfunctions
Mögliche
The table below contains descriptions of possible causes and solutions to
malfunctions or errors during operation of the appliance. When malfunction cannot
be removed, contact the technical service.
In such a case, provide article number, model name and serial number. These data
may be found in the rating plate.
174196 27 / 28
Disposal
EN
Electric appliances are marked with this symbol. Electrical
appliances must be disposed of and recycled in a correct
and environmentally friendly manner. You must not dispose
of electric appliances with household waste. Disconnect the
appliance from the power supply and remove power cord
from the appliance.
8 Disposal
Electrical Appliance
Electrical appliances should be returned to designated collection points.
28 / 28 174196
Loading...