Regina Plus 40T
Regina
Plus
90T
A190146
A190196
V1/0814
A190146
A190196
Ø 220
Ø 2
70
312
420
460
360
②
⑦
⑨
④
⑤
⑧
⑥
③
①
⑬ ⑩
⑪
⑫
- 19 -
ENGLISH
Translation
of the original instruction manual
Read these instructions before using and keep
them available at all times!
1. General information ................................................................................................ 20
1.1 Information about the instruction manual ............................................................ 20
1.2 Key to symbols .................................................................................................... 20
1.3 Liability and Warrantees ...................................................................................... 21
1.4 Copyright protection ............................................................................................ 21
1.5 Declaration of conformity ..................................................................................... 21
2.Safety ........................................................................................................................ 22
2.1 General information ............................................................................................. 22
2.2 Safety instructions for use of the device .............................................................. 22
2.3 Intended use ....................................................................................................... 23
3. Transport, packaging and storage......................................................................... 24
3.1 Delivery check ..................................................................................................... 24
3.2 Packaging ........................................................................................................... 24
3.3 Storage ................................................................................................................ 24
4. Technical data ......................................................................................................... 25
4.1 Technical specification ........................................................................................ 25
4.2 Overview of parts ................................................................................................ 26
5. Installation and operation ....................................................................................... 27
5.1 Safety instructions ............................................................................................... 27
5.2 Installation and connection .................................................................................. 27
5.3 Operation ............................................................................................................ 28
6. Cleaning and maintenance ..................................................................................... 31
6.1 Safety advice ....................................................................................................... 31
6.2 Cleaning and descaling ....................................................................................... 32
6.3 Safety instructions for maintenance .................................................................... 35
7. Possible Malfunctions ............................................................................................ 35
8. Waste disposal ........................................................................................................ 36
Bartscher GmbH
Franz-Kleine-Str. 28
D-33154 Salzkotten phone: +49 (0) 5258 971-0
Germany fax: +49 (0) 5258 971-120
GB/UK
- 20 -
1. General information
1.1 Information about the instruction manual
This instruction manual contains information about the installation, operation and
maintenance of the device and should be consulted as an important source of
information and reference guide.
Awareness of the safety instructions and instructions for use in this manual will ensure
the safe and correct use of the device.
In addition to the information given here, you should comply with any local Health and
safety Controls and generally applicable safety regulations.
The instruction manual forms part of the product and should be kept near the device
and easily accessible for anyone carrying out the installation, servicing, maintenance or
cleaning.
1.2 Key to symbols
In this manual, symbols are used to highlight important safety instructions and any
advice relating to the device. The instructions should be followed very carefully to avoid
any risk of accident, personal injury or material damage.
WARNING!
This symbol highlights hazards, which could lead to injury.
Please follow the instructions very carefully and proceed with particular attention
in these cases.
WARNING! Electrical hazard!
This symbol draws attention to potential electrical hazards. If you do not follow
the safety instructions, you may risk injury or death.
CAUTION!
This symbol highlights instructions, which should be followed to avoid any risk of
damage, malfunctioning and/or breakdown of the device.
NOTE!
This symbol highlights tips and information, which have to be followed for
an efficient and trouble-free operation of the device.
WARNING! Hot surface!
This symbol is a warning that the device surface is hot when in use. Ignoring this
warning may result in burns!
- 21 -
1.3 Liability and Warrantees
All the information and instructions in this manual take into account standard safety
regulations, current levels of technical engineering as well as the expertise and
experience we have developed over the years.
The instruction manual was translated with all due care and attention. However, we do
not accept liability for any translation errors. The German version of this instruction
manual is definitive.
If the delivery consists of a special model, the actual scope of delivery may differ from
the descriptions and illustrations in this manual. This is also the case for special orders
or when the device has been modified in line with new technology.
NOTE!
Read this manual carefully and thoroughly before any operation of the device,
and especially before turning it on!
Manufacturer is not liable for any damages or faults caused by:
- violation of advice concerning operation and cleaning;
- use other than designed;
- alterations made by user;
- use of inadequate spare parts.
We reserve the right to make technical changes for purposes of developing and improving
the useful properties.
1.4 Copyright protection
The instruction manual including any texts, drawings, images or other illustrations is
copyright. No part of this publication may be reproduced, transmitted or used in any
form or by any means without permission in writing from the manufacturer. Any person
who commits any unauthorized act in relation to this publication shall be liable to claims
for damages. All rights reserved.
NOTE!
The contents, texts, drawings, pictures and any other illustrations are copyright
and subject to other protection rights. Any person unlawfully using this
publication is liable to criminal prosecution.
1.5 Declaration of conformity
The device complies with the current standards and directives of the EU.
We certify this in the EC declaration of conformity. If required we will be
glad to send you the according declaration of conformity.
- 22 -
2.Safety
This section provides an overview of all important safety aspects.
In addition every chapter provides precise safety advice for the prevention of dangers
which are highlighted by the use of the above mentioned symbols.
Furthermore, attention should be paid to all pictograms, markers and labels on the
device, which must be kept in a permanent state of legibility.
By following all the important safety advice you gain an optimal protection against all
hazards as well as the assurance of a safe and trouble-free operation.
2.1 General information
This device is designed in accordance with the presently applicable technological
standards. However, the device can pose a danger if handled improperly and
inappropriately.
Knowing the contents of the instruction manual as well as avoiding mistakes and thus
operating this device safely and in a fault-free manner is very essential to protect
yourselves from the hazards.
To prevent hazards and to ensure optimum efficiency, no modifications or alterations to
the device that are not explicitly approved by the manufacturer may be undertaken.
This device may only be operated in technically proper and safe condition.
2.2 Safety instructions for use of the device
The specifications regarding the industrial safety are based on the Regulations of the
European Union applicable at the time of manufacturing the device.
If the device is used commercially, the user is obliged to ensure that the said industrial
safety measures concur with the state of the rules and regulations applicable at the time
in question for the entire period of use of the device and to comply with the new
specifications.
Outside the European Union, the industrial safety laws applicable at the place of
installation of the device and the regional territorial provisions must be complied with.
Besides the industrial safety instructions in the instruction manual, the general safety and
accident prevention regulations as well as environment protection regulations applicable
for area of application of the device must be followed and complied with.
CAUTION!
o The device can be used by children 8 years and up, as well as by people with
disabilities and those with limited experience/knowledge as long as they are under
supervision or have been instructed on proper use of the device and its possible
dangers.
- 23 -
o Children should not play with the device.
o Cleaning and maintenance cannot be performed by children younger than 8 years
old and must be done under supervision.
o Children under the age of 8 years old must be kept away from the device and its
power cord.
o Please keep these instructions and give them to future owners of the device.
o All people using the device should follow the instructions and tips contained in these
instructions.
o Only use the device indoors.
2.3 Intended use
Safe operation is only guaranteed when using the device for its intended purpose.
Any technical interventions, as well as assembly and maintenance are to be made by a
qualified customer service only.
The device is intended for home use or in similar places such as:
- in kitchens for store or office employees or in other service locations;
- in suburban properties;
- by guests of hotels, motels and other places of accommodation;
-
in Bed & Breakfasts.
The coffee maker with round filter is only intended for the preparation of coffee
and warm or hot water using cold water.
Do not use the coffee maker with round filter for:
- preparing other beverages;
- heating or cooking liquids containing sugar, sweetener,
acid, lye or alcohol;
- filling and heated liquids and other substances that are combustible,
harmful to the health or quickly become volatile.
CAUTION!
Any use going beyond the intended purpose and/or any different use of the
device is forbidden and is not considered as conventional.
Any claims against the manufacturer or his authorized representative as a
consequence of experiencing damages resulting from unconventional use are
impossible.
The operator is liable for all damages resulting from inappropriate use.
- 24 -
3. Transport, packaging and storage
3.1 Delivery check
Please check the delivery upon completeness and transport damage immediately
after receipt. In case of visible damage do not accept or accept the delivery with
reservation only.
Note the extent of damage on the carrier’s bill of delivery. Trigger off the complaint.
Hidden damages should be reclaimed immediately after notice, as claims for damages
can only be asserted within the effective period for complaints.
3.2 Packaging
Please do not throw away the covering carton of your device as it might be useful for
storage purposes, when moving or, in case of damages, when the device must be sent
back to a repair center. The outer and inner packing material should be removed
completely from the device before installation.
NOTE!
If you liked to dispose the packing, consider the regulations applicable in your
country. Supply re-usable packing materials to the recycling.
Please inspect the device upon completeness. In case any part is missing please
contact our customer service center immediately.
3.3 Storage
Keep the package closed until installation and under consideration of the outside
indicated positioning- and storage markings.
Packages should be stored under consideration of the following:
- Do not store outdoors.
- Keep it dry and dust-free.
- Do not expose it to aggressive media.
- Do not expose it to direct sunlight.
- Avoid mechanical shocks and vibration.
- In case of longer storage (> 3 months) make sure you check
the state of the packaging and the parts regularly.
If required refresh or renew.
- 25 -
4. Technical data
4.1 Technical specification
Name
Coffee maker with round filter
Model:
Regina Plus 40T Regina Plus 90T
Code-No:
A190146 A190196
Material: stainless steel housing; plastic base and lid
Capacity: 6.8 litres 15.0 litres
Brewing time for
maximum capacity:
approx. 45 minutes approx. 60 minutes
Minimum brewed
amount:
3.0 litres (20 cups) 4.5 litres (30 cups)
Power supply: 1,2 kW / 220-240 V 50/60 Hz 1,6 kW / 220-240 V 50/60 Hz
Abmessungen: Ø 220 mm, H 420 mm Ø 270 mm, H 460 mm
Gewicht: 3.1 kg 4.1 kg
We reserve the right to make technical changes!
Additional equipment (not included in the delivery!)
Round paper filter
Regina Plus 40T
(250 pieces per package)
Code-No.:A190009250
Round paper filter
Regina Plus 40T
(1000 pieces per package)
Code-No.: A190009
Round paper filter
Regina Plus 90T
(250 pieces per package)
Code-No.: A190011250
Round paper filter
Regina Plus 90T
(1000 pieces per package)
Code-No.: A190011
Quick descaler
for coffee makers
(30 bags 15 g each)
Code-No.: 190065
- 26 -
4.2 Overview of parts
NOTE!
On the folded page of the instruction manual is listed
the most important components of the coffee maker.
This page should always be opened when reading
the instruction manual.
①
Cover handle
②
Cover
③
Water container handle
④
Water container
⑤
ON/OFF switch with integrated indicator light (red)
⑥
Indicator light for maintaining hot water (green)
⑦
Descaling indicator (red)
⑧
Faucet
⑨
Fill level indicator
⑩
Filter basket
⑪
Riser pipe
⑫
Heating hole
⑬
Scale deposit scraper
- 27 -
5. Installation and operation
5.1 Safety instructions
• Never allow the power cable to come into contact with heat sources or sharp edges.
The power cable should not hang over the side of the working surface. Ensure that
no one can step on or trip over the cable.
• The power cable must not be folded, bent or tangled, and must always remain fully
unrolled.
• Never place the device or other objects on the power cable.
• Do not lay the cable over carpets or heat insulations. Do not cover the cable.
Keep away the cable from operating range and do not dunk it into water.
• Do not use the device in case it does not function properly, has been damaged or
dropped.
• Do not use any accessory or spare parts that have not been recommended by the
manufacturer. These can be dangerous for the user or lead to damages of the
device or personal injury, and further, the warranty expires.
• Protect the device from frost and moisture.
• Never use the device with wet or moist hands.
• Never leave the device unattended when in use.
• Never fill hot water into the cold water tank.
• Do not fill water into the hot device; wait until it has cooled down.
• Do not move or tilt the device when in operation.
WARNING! Hot surface!
During operation some parts of the device become very hot. In order to avoid
injuries do not touch any hot parts!
5.2 Installation and connection
• Unpack the device and remove all packing material.
• Put the device in a safe place that can support its weight and is not heat sensitive.
• Never place the device on a combustible surface.
• Never place the device at the edge of a table to avoid accidents.
• Never put the device in a moist or wet area.
• Do not place the device near an open flame, electric heater or other heat source.
- 28 -
WARNING! Hazard via electrical current!
The device can cause injuries due to improper installation!
Before installation the local power grid specification should be compared with
that of the device (see type label).
Connect the device only in case of compliance! Take note of the security advice!
The device must only be connected to a properly installed single socket with
protective contact.
Never remove the power cable by pulling the cable itself; always grab the plug
housing.
• The electrical circuit of the socket must be secured to at least 16A. Only connect
the device to a wall outlet; do not use any extension cords or power strips.
• Place the device so that the plug is easily accessible so as to quickly disconnect the
device if the need arises.
5.3 Operation
Preparing the device
• Remove the cover and then remove the filter basket together with the riser pipe
from the water container.
• Before the first use clean the filter basket, cover and water container interior with
warm water and a mild detergent. Rinse thoroughly with clean water to remove
remnants of detergent.
ATTENTION!
Do not immerse the bottom of the device in water!
• Clean the riser pipe with warm water and a mild detergent. Rinse thoroughly with
clean water.
• To assemble the device, insert the riser pipe in the filter basket opening, and then
both parts insert together into the container. Please remember that the riser pipe
should be inserted into the heating hole in the bottom of the container in the center.
- 29 -
Brewing coffee
• Fill the water container with cold water (the necessary amount of water can be read
from the filling indicator level).
• Observe the minimum amount of coffee for brewing. It is:
for device A190146 → 20 cups → about 3.0 liters
for device A190196 → 30 cups → about 4.5 liters
ATTENTION!
Do not fill the coffee maker with water above the highest marks!
Never use warm water to brew coffee!
• Place the filer basket assembly into the coffee maker so that the riser pipe is inserted
into the heating hole in the bottom of the container in the center. Do not force the
riser pipe into position.
• Insert a round paper filter into the filter basket.
NOTE!
Only round paper filters should be used with the coffee maker with round filter
We recommend using BARTSCHER round paper filters numbers A190190 or
A190009250 for models Regina Plus 40T (A190146) and round paper filters numbers
A190011 or A190011250 for models Regina Plus 90T (A190196).
• Pour ground coffee (about 6 grams per cup) into the filter basket.
NOTE!
The recommended amount of coffee may be increased or decreased according to
one's preferences.
• Close to coffee maker cover. When closing follow the instructions given on the cover.
WARNING!
During operation, never open the cover. There is a danger of burns!
- 30 -
• Start the coffee maker by switching the ON/OFF switch to position „I“. During the
boiling process the red operation control light in the switch will come on.
• The green heat retention light will come on when the boiling process has completed.
As soon as the brewing process is finished, the temperature is reduced automatically
and the coffee is kept at temperature proper for serving until the power plug is
disconnected from power supply or the ON/OFF switch is set to „O“.
NOTE!
To heat the coffee, remove the riser pipe and filter basket. Turn on the device.
The container must contain the amount of coffee for at least 12 cups.
• Unplug the cord when no liquid flows from the faucet of the standing device.
• The device is equipped with a heat/boil-dry protection. If the device is accidentally
turned on with little or no liquid, the protection device trips and the device switches
off automatically.
ATTENTION!
In the event that the overheating protection turns on,
disconnect the device from the power source (pull the
plug!) and leave to cool.
Press the RESET button on the bottom of the device
quickly several times.
The coffee maker is now ready for use.
Serving coffee
• Place the cup or glass under the drain valve, press the valve slightly down and hold
until the cup is filled with required amount of coffee.
• Release the drain valve which is closed automatically.
• In order to obtain full flow press the valve lever fully down.
NOTE!
The drain valve is located a little higher, therefore the dregs remain on the water
tank bottom and do not enter the served coffee.
• When the device is placed in normal position and the coffee does not flow, remove
the plug and fill the device with fresh water after cooling down, when required.
- 31 -
Instructions and advices
NOTE!
The best results can be achieved when coffee is prepared for at
least 20 or 30 cups at once.
Remove the filter basket and coffee grounds immediately after the
brewing process. Thanks to this the coffee's flavor is maintained.
WARNING! Danger of burns!
Elements of the filter basket and grounds are very hot.
During removal, use appropriate protective equipment!
• Before starting the next batch of coffee, you should thoroughly rinse the coffee
brewer with cold water.
• Any drops arising from removing the filter basket and the wet coffee grounds should
be wiped clean.
• In order to re-heat cold coffee you should remove the filter basket and riser pipe
before connecting the device to the power.
• The coffee machine can also be used to heat water. Fill the cleaned water container
with cold water; insert the riser pipe and cleaned filter basket. Turn on the device, as
in brewing coffee.
• Set the ON/OFF switch to position „O“ when the heating is finished.
• Pull the power plug as soon as less than four cups of water are left in the water tank.
NOTE!
If the device will not be used, remove the riser pipe, otherwise it might get stuck
in the heating hole.
6. Cleaning and maintenance
6.1 Safety advice
o Before beginning with repair or cleaning works make sure the device has been
disconnected from power supply and has cooled down.
o Do not use any acid agents and make sure no water ingresses the device.
o To protect yourself from electric shock, never immerse the device, its cables and
the plug in water or other liquids.
CAUTION!
The device is not suited for direct washing via water jets.
Therefore, you must not use any kind of pressure water jet for cleaning the device!
- 32 -
6.2 Cleaning and descaling
Daily cleaning
o Clean the device after each use.
o After use, wash the device with hot water and a mild, commercially available
detergent for coffee makers. Clean also the filter basket, riser pipe and cover.
Please observe the instructions of the manufacturer.
o Dry these items with a soft cloth.
o The water container should be cleaned of all sediments and coffee remnants.
It can be cleaned with a mild abrasive cleaner and cleaning pan.
o Wipe the surface of the coffee maker with a damp cloth and then dry with a soft cloth.
o To clean the faucet after use, fill the coffee maker with warm water and drain it
through the faucet.
Weekly cleaning
o If the device is used daily, it is necessary to thoroughly clean the spout mechanism
once weekly, or less frequently in case of less intensive use.
o In order to clean the device unscrew the tap lid and remove the closing cone. Wash all
parts in warm water with the gentle washing agent. Use appropriate bottlebrush to
clean the tap and its connection with the coffee maker.
CAUTION!
You must not insert the brush into the assembled tap as it may damage the
closing cone.
o All parts of the tap should be rinsed with cleaned water and thoroughly dried.
Reassemble the tap.
o
When required, the
level indicator (a)
may be cleaned
with use of appropriate bottlebrush.
Unscrew the upper screw (d), disconnect the glass
pipe (b) and remove the upper seal (c). Insert the
bottlebrush to the glass pipe (b) and clean it
thoroughly with use of warm water and gentle washing
agent. Thoroughly rinse with clean water.
Then reassemble the level indicator. Pay attention to
correct positioning of the lowe and upper seal (c).
a
b
d
c
c
- 33 -
CAUTION!
Check if the glass pipe is correctly positioned in the seal.
Tighten the fitting gently, otherwise the glass pipe may break.
o Tighten the screw (d) of the level indicator.
Cleaning the heating hole
o The heating hole must be thoroughly cleaned every week, especially if used daily.
o Included in the coffee maker packaging is a scale deposit scraper for cleaning the
heating hole at the bottom of the coffee maker.
NOTE!
Only the attached scale deposit scraper should be used!
o Place a cloth soaked with soapy
steel wool or a thin cloth for
scrubbing over the heating hole.
o Insert the narrow end of the
scraper into the heating hole.
o By rotating repeatedly clean
heating hole.
o When the heating hole is clean,
the metal will shine.
o After completion of cleaning, thoroughly rinse the water container in order to remove
all residues of soaps and cleaning detergents.
Heating hole
Scale deposit
scraper
- 34 -
Descaling
ATTENTION!
In order to extend the use of the device and to ensure good quality coffee, the
coffee maker should be descaled regularly!
Claims will not be accepted if the coffee maker will not be descaled regularly,
as described in the instruction manual.
Such claims are not covered under the warranty!
o The device is equipped with red descaling indicator. Depending on the hardness of
used water the indicator may be activated after some brewing cycles, which indicates
that the device must be descaled. At the same time the overheating protection is
activated and the device is turned off.
o After descaling the coffee maker must be turned on only after pressing the RESET
button in the base. When the device is turned on after descaling, the indicator is not
activated.
o For descaling the device we recommend "Rapid descaler for coffee makers"
that we have tested.
Code-No.: 190065; packing unit: (30 bags 15 g each).
o Dissolve the content of the bag (15 g) in approximately 5 liters of water.
o Push the riser pipe through the center of the filter basket and place it in the water
container. Make sure that the riser pipe has been carefully inserted in the heating hole.
o Pour the descaling mixture into the water container of the coffee maker. Place the
cover on the water container and turn on the device.
o Start the brewing process and leave the coffee maker on for about 15 minutes.
o Turn off the device and drain the descaling mixture from the water container through
the faucet.
o After descaling, perform the brewing process at least three times to remove all
remnants of the descaling mixture.
o Rinse thoroughly with warm water the water container, riser pipe, filter basket and
drain this water through the faucet.
o The coffee maker is now ready for use.
WARNING!
Do not leave the coffee maker without supervision while descaling!
During descaling use gloves and goggles!
o After descaling carefully wash your hands.
- 35 -
6.3 Safety instructions for maintenance
o Inspect the power cable regularly for damage. Never use the device if the cable is
damaged. If the power cable is damaged, have an authorised service center or
qualified electrician replace it.
o In case of damage or malfunction, please contact your stockist or our customer
service centre. Pay attention to the troubleshooting tips in pt. 7.
o Only a qualified technician and using original spare parts and accessories should
carry out repairs and maintenance of the device. Do not attempt to repair the
device yourself.
7. Possible Malfunctions
Problem Cause Solution
The device is turned on,
but the red indicator light
does not turn on.
• The power plug is not
properly inserted into
the socket.
• Disconnected fuse.
• Damaged indicator light.
• Damaged switch.
• Properly insert the plug
into the socket.
• Check the fuse.
• Check the device in
another socket.
• Contact a salesperson.
Red descaling indicator is
on during the operation.
• The device is scaled.
• Remove the plug. Leave
the device until cooling
down, then descale it
according to section
6.2 „Cleaning and
descaling“
The device is turned on,
the ON/OFF switch
indicator is on, but the
device is not heating.
• Damaged heating
element.
• Damaged thermostat.
• Contact a salesperson.
• Contact a salesperson.
The device turns off.
• The overheating
protection was
triggered.
• The device is scaled.
• Remove the plug. Wait until
the device cools down and
press the RESET button in
the base. Maintain appropriate filling level.
Descale the device
according to section
6.2 „Cleaning and
descaling“
- 36 -
Problem Cause Solution
The green indicator light
does not turn on.
• The brewing / heating
process is not completed yet.
• Damaged indicator light.
• Damaged thermostat.
• Wait until the brewing /
heating process will be
completed
• Contact a salesperson.
• Contact a salesperson.
The fuse blows immediately after turning on.
• Electrical short circuit. • Contact a salesperson.
The above cases are only for illustration and should be used for better orientation.
If the same or similar problems occur, immediately turn off the device and do not
use it. If you cannot remedy the source of the fault yourself according to the above
examples, you should contact customer service or the salesperson.
8. Waste disposal
Discarding old devices
At the end of its service life the discarded device has to be disposed in accordance with
the national regulations. It is advisable to contact a company which is specialized in
waste disposal, or just contact the local disposal service in your community.
WARNING!
To exclude any abuse and the dangers involved make the waste device unfit for
use before disposal. For that purpose disconnect device from mains supply and
remove mains connection cable from the device.
NOTE!
For the disposal of the device please consider and act
according to the national and local rules and
regulations.
Bartscher GmbH
Franz-Kleine-Str. 28
D-33154 Salzkotten phone: +49 (0) 5258 971-0
Germany fax: +49 (0) 5258 971-120
Loading...