Bartscher MultiTherm, A200050 Instruction Manual

Bedienungsanleitung

Instruction manual

Mode

d’emploi

Gebruiksaanwijzing

Instrukcja

obsługi

V

6/0814

„MultiTherm“

A200050

Glühweintopf

Seite 1 bis 14

Mulled wine pot

from page 15 to 28

Marmite à vin chaud

de page 29 à page 42

D/A/CH

GB/UK

F/B/CH

Glühwein ketel

blz. 43 t/m 56

Warnik do grzanego wina

strony od 57 do 70

NL/B

PL

GB/UK

ENGLISH
Translation
of the original instruction manual

Read these instructions before using and keep
them available at all times!

1. General information ................................................................................................ 16

1.1 Information about the instruction manual ............................................................ 16

1.2 Key to symbols .................................................................................................... 16

1.3 Liability and Warrantees ...................................................................................... 17

1.4 Copyright protection ............................................................................................ 17

1.5 Declaration of conformity ..................................................................................... 17

2.Safety ........................................................................................................................ 18

2.1 General information ............................................................................................. 18

2.2 Safety instructions for use of the device .............................................................. 18

2.3 Intended use ....................................................................................................... 19

3. Transport, packaging and storage......................................................................... 20

3.1 Delivery check ..................................................................................................... 20

3.2 Packaging ........................................................................................................... 20

3.3 Storage ................................................................................................................ 20

4. Technical data ......................................................................................................... 21

4.1 Overview of parts ................................................................................................ 21

4.2 Technical specification ........................................................................................ 22

5. Installation and operation ....................................................................................... 23

5.1 Safety instructions ............................................................................................... 23

5.2 Installation and connection .................................................................................. 23

5.3 Operation ............................................................................................................ 24

6. Cleaning and maintenance ..................................................................................... 26

6.1 Safety advice ....................................................................................................... 26

6.2 Cleaning .............................................................................................................. 26

6.3 Safety instructions for maintenance .................................................................... 27

7. Possible Malfunctions ............................................................................................ 27

8. Waste disposal ........................................................................................................ 28

Bartscher GmbH
Franz-Kleine-Str. 28
D-33154 Salzkotten phone: [phone]
Germany fax: [phone]

- 15 -

1. General information

1.1 Information about the instruction manual

This instruction manual contains information about the installation, operation and
maintenance of the device and should be consulted as an important source of
information and reference guide.

Awareness of the safety instructions and instructions for use in this manual will ensure
the safe and correct use of the device.

In addition to the information given here, you should comply with any local Health and
safety Controls and generally applicable safety regulations.

The instruction manual forms part of the product and should be kept near the device
and easily accessible for anyone carrying out the installation, servicing, maintenance or
cleaning.

1.2 Key to symbols

In this manual, symbols are used to highlight important safety instructions and any
advice relating to the device. The instructions should be followed very carefully to avoid
any risk of accident, personal injury or material damage.

WARNING!

This symbol highlights hazards, which could lead to injury.
Please follow the instructions very carefully and proceed with particular attention
in these cases.

WARNING! Electrical hazard!

This symbol draws attention to potential electrical hazards. If you do not follow
the safety instructions, you may risk injury or death.

CAUTION!

This symbol highlights instructions, which should be followed to avoid any risk of
damage, malfunctioning and/or breakdown of the device.

NOTE!

This symbol highlights tips and information, which have to be followed for
an efficient and trouble-free operation of the device.

WARNING! Hot external surface!

This symbol is a warning that the device surface is hot when in use. Ignoring this
warning may result in burns!

- 16 -

1.3 Liability and Warrantees

All the information and instructions in this manual take into account standard safety
regulations, current levels of technical engineering as well as the expertise and
experience we have developed over the years.

The instruction manual was translated with all due care and attention. However, we do
not accept liability for any translation errors. The German version of this instruction
manual is definitive.

If the delivery consists of a special model, the actual scope of delivery may differ from
the descriptions and illustrations in this manual. This is also the case for special orders
or when the device has been modified in line with new technology.

NOTE!

Read this manual carefully and thoroughly before any operation of the device,
and especially before turning it on!

Manufacturer is not liable for any damages or faults caused by:

- violation of advice concerning operation and cleaning;

- use other than designed;

- alterations made by user;

- use of inadequate spare parts.

We reserve the right to make technical changes for purposes of developing and improving
the useful properties.

1.4 Copyright protection

The instruction manual including any texts, drawings, images or other illustrations is
copyright. No part of this publication may be reproduced, transmitted or used in any
form or by any means without permission in writing from the manufacturer. Any person
who commits any unauthorized act in relation to this publication shall be liable to claims
for damages. All rights reserved.

NOTE!

The contents, texts, drawings, pictures and any other illustrations are copyright
and subject to other protection rights. Any person unlawfully using this
publication is liable to criminal prosecution.

1.5 Declaration of conformity

The device complies with the current standards and directives of the EU.
We certify this in the EC declaration of conformity. If required we will be
glad to send you the according declaration of conformity.

- 17 -

2.Safety

This section provides an overview of all important safety aspects.
In addition every chapter provides precise safety advice for the prevention of dangers

which are highlighted by the use of the above mentioned symbols.
Furthermore, attention should be paid to all pictograms, markers and labels on the

device, which must be kept in a permanent state of legibility.
By following all the important safety advice you gain an optimal protection against all

hazards as well as the assurance of a safe and trouble-free operation.

2.1 General information

This device is designed in accordance with the presently applicable technological
standards. However, the device can pose a danger if handled improperly and
inappropriately.

Knowing the contents of the instruction manual as well as avoiding mistakes and thus
operating this device safely and in a fault-free manner is very essential to protect
yourselves from the hazards.

To prevent hazards and to ensure optimum efficiency, no modifications or alterations to
the device that are not explicitly approved by the manufacturer may be undertaken.

This device may only be operated in technically proper and safe condition.

2.2 Safety instructions for use of the device

The specifications regarding the industrial safety are based on the Regulations of the
European Union applicable at the time of manufacturing the device.

The user is obliged to ensure that the said industrial safety measures concur with the
state of the rules and regulations applicable at the time in question for the entire period
of use of the device and to comply with the new specifications.

Outside the European Union, the industrial safety laws applicable at the place of
installation of the device and the regional territorial provisions must be complied with.

Besides the industrial safety instructions in the instruction manual, the general safety and
accident prevention regulations as well as environment protection regulations applicable
for area of application of the device must be followed and complied with.

CAUTION!

o The device can be used by children 8 years and up, as well as by people with

disabilities and those with limited experience/knowledge as long as they are under
supervision or have been instructed on proper use of the device and its possible
dangers.

o Children should not play with the device.

- 18 -

o Cleaning and maintenance cannot be performed by children younger than 8 years

old and must be done under supervision.

o Children under the age of 8 years old must be kept away from the device and its

power cord.

o Please keep these instructions and give them to future owners of the device.
o All people using the device should follow the instructions and tips contained in these

instructions.

2.3 Intended use

Safe operation is only guaranteed when using the device for its intended purpose.
Any technical interventions, as well as assembly and maintenance are to be made by a

qualified customer service only.
The device is not adapted for use with an external timer or remote control.
The device is intended for home use or in similar places such as:

- in kitchens for store or office employees or in other service locations;

- in suburban properties;

- by guests of hotels, motels and other places of accommodation;

-

in Bed & Breakfasts.

Mulled wine pot „MultiTherm“ is meant only for heating up and keeping the heat of
liquids suitable for drinking, such as e.g. heated wine, tea and for preparing hot water.

Do not use the mulled wine pot „MultiTherm“ for:

- cooking food;

- warming up or heating of inflammable, volatilizing,

noxious or similar fluids or materials.

CAUTION!

Any use going beyond the intended purpose and/or any different use of the
device is forbidden and is not considered as conventional.
Any claims against the manufacturer or his authorized representative as a
consequence of experiencing damages resulting from unconventional use are
impossible.
The operator is liable for all damages resulting from inappropriate use.

- 19 -

3. Transport, packaging and storage

3.1 Delivery check

Please check the delivery upon completeness and transport damage immediately
after receipt. In case of visible damage do not accept or accept the delivery with
reservation only.

Note the extent of damage on the carrier’s bill of delivery. Trigger off the complaint.
Hidden damages should be reclaimed immediately after notice, as claims for damages

can only be asserted within the effective period for complaints.

3.2 Packaging

Please do not throw away the covering carton of your device as it might be useful for
storage purposes, when moving or, in case of damages, when the device must be sent
back to a repair center. The outer and inner packing material should be removed
completely from the device before installation.

NOTE!

If you liked to dispose the packing, consider the regulations applicable in your
country. Supply re-usable packing materials to the recycling.

Please inspect the device upon completeness. In case any part is missing please
contact our customer service center immediately.

3.3 Storage

Keep the package closed until installation and under consideration of the outside
indicated positioning- and storage markings.

Packages should be stored under consideration of the following:

- Do not store outdoors.

- Keep it dry and dust-free.

- Do not expose it to aggressive media.

- Do not expose it to direct sunlight.

- Avoid mechanical shocks and vibration.

- In case of longer storage (> 3 months) make sure you check

the state of the packaging and the parts regularly.
If required refresh or renew.

- 20 -

4. Technical data

4.1 Overview of parts

①

⑩

⑨

⑧

①

Lid

②

⑦

④

⑤

⑥

③

Handle of lid

②

Container handle

③

Container

④

Temperature control

⑤

Green keeping warm control lamp

⑥

Orange heating up control lamp

⑦

Socket

⑧

Drainer / Placing platter for glass/cup

⑨

Tap/faucet

⑩

- 21 -

Heat

-

retaining lid for

cups

4.2 Technical specification

Description:

Mulled wine pot „MultiTherm“

Code-No.:

A200050

Material: Body and lid: stainless steel
Connection: 2000 W / 220-240 V 50/60 Hz
Temperature control:

stepless, 30 °C - 90 °C

Capacity: 20 litres
Dimensions: Ø 270 mm, height 610 mm
Weight: 4.8 kg
Accessories:

3 labels: Glühwein, Jagertee, hot water - Tea

We reserve the right to make technical changes!

Accessories

(not included in the packaging)

Suitable for approx. 10 - 15 cups
Material: stainless steel
Ø 354 mm, Rim height: 40 mm
Weight: 0.78 kg

Code-No.: 200058

- 22 -

5. Installation and operation

5.1 Safety instructions

• Never allow the power cable to come into contact with heat sources or sharp edges.
The power cable should not hang over the side of the working surface. Ensure that no
one can step on or trip over the cable.

• The power cable must not be folded, bent or tangled, and must always remain fully
unrolled.

• Never place the device or other objects on the power cable.

• Do not lay the cable over carpets or heat insulations. Do not cover the cable. Keep

away the cable from operating range and do not dunk it into water.

• Do not use the device in case it does not function properly, has been damaged or
dropped.

• Do not use any accessory or spare parts that have not been recommended by the
manufacturer. These can be dangerous for the user or lead to damages of the
device or personal injury, and further, the warranty expires.

• Protect the device from rainwater, moisture and dampness.

• Do not move or tilt the device when in operation.

WARNING! Hot surface!

During operation some elements of the device very become hot.
To avoid burns, do not touch hot elements!

5.2 Installation and connection

• Discard the complete packing material after unpacking the device.

• Place the device on top of an even and safe surface which supports the weight of

the device and is not heat sensitive.

• Not at any time should you place the device on an inflammable surface.

• You must not position the device near open fireplaces, electric ovens/arc furnaces,

furnaces/electric heaters or other heat sources.

• Do not place any acid chemicals, gases or other, easily inflammable materials near
this device.

- 23 -

WARNING! Hazard via electrical current!

The device can cause injuries due to improper installation!
Before installation the local power grid specification should be compared with

that of the device (see type label). Connect the device only in case of compliance!
The device must only be connected to a properly installed single socket with

protective contact.
Never remove the power cable by pulling the cable itself; always grab the plug

housing.

• The electrical circuit in the socket must be secured to at least 16A. Only connect the
device directly to the wall socket; do not use any extension cords or power strips.

• Place the device so that the plug is easily accessible and can be quickly removed
from its socket in case of necessity.

5.3 Operation

• Before using the device, clean it in accordance with the instructions contained in

6.2 „Cleaning“.

• Turn the temperature control with the red dot all the way to the left.

• Plug the power plug into the socket (the green control lamp lights up).

CAUTION!

It is important that there is always drinkable liquid in the container before
engaging the device. You must not pour undrinkable liquids such as acids,
bases or leys, oils, nitrates etc. in the mulled wine pot.

• Pour the desired drinkable liquid in the mulled wine pot.
Minimum filling quantity of 2 litres.

WARNING!

During operation it must be ensured that no liquids can spill over as this can
cause short-circuits in the electronic control. Personal injury can be the result.

• The temperature control is infinitely variable between approx. 30 °C - 90 °C.

- 24 -

NOTE!

The heat is created via a heating coil in the bottom part of the mulled wine pot.
The electric temperature control with the temperature sensor are placed here
as well. The adjustment of temperature is done via the thermostat switch.

• Turn the temperature control with the red dot rightwards and set it to the desired
temperature (the orange control lamp flashes up). When the desired (set)
temperature is reached the orange control lamp switches off and the green control
lamp flashes up (warm keeping mode).

NOTE!

The heating time depends on the liquid and the amount. When the desired liquid
temperature is reached the thermostat shuts off automatically.
In case the liquid temperature drops below the desired temperature the
thermostat switches on to keep the liquid at the set temperature over a larger
period of time.

• For tapping/drawing liquid turn the handle of the stop valve
to the front. After finishing the tapping of liquid turn back
the stop valve to its original position.

• Conditional on the system a quantity of approx. 1 litres
remains in the container. This quantity can be slightly
reduced by carefully tilting the container forward.

WARNING! Danger of burn!

While operating the mulled wine pot the surface of the container will be heated up
according to the adjusted temperature! Do not touch hot surface!

• When the device is not in use, make sure you the temperature controller is turned all
the way to the left as far as it will go, pull the power plug out of the socket, let the
liquid drain and clean the container after it has cooled off.

• The device is equipped with protection against overheating. If the device happens
to be empty when turned on, the overheating protection will be activated. Remove
the plug from its socket and leave the device to cool for approx. 30 minutes.
Let the liquid drain. Pull the device with the drainer upward out of the socket.

Next, press the RESET button located at the bottom of the device. The device is
ready for use. In case the device does not work properly afterwards, contact you
customer service.

- 25 -

6. Cleaning and maintenance

6.1 Safety advice

o Before beginning with repair or cleaning works make sure the device has been

disconnected from power supply and has cooled down.

o Do not use any acid agents and make sure no water ingresses the device.
o To protect yourself from electric shock, never immerse the device, its cables and

the plug in water or other liquids.

CAUTION!

The device is not suited for direct washing via water jets.
Therefore, you must not use any kind of pressure water jet for cleaning the device!

6.2 Cleaning

o The device should be cleaned regularly.
o The surface of the device should be cleaned with a damp cloth. For tenacious stains

a mild detergent can be used. Do not use any sprays or aggressive detergents.

o Clean the device thoroughly inside and rinse it with clean water.
o Only use a soft cloth and make sure you never use any kind of abrasive agents or

pads which could scratch the surface.

o Do not use steel wool for cleaning purposes. Parts of the steel wool can loosen and

settle in the stop valve and lead to damages of the seal faces.

o If the device is used daily the whole faucet mechanism has to be cleaned once a week.

If the device is used less often, it may be cleaned less frequently. For cleaning the
faucet bonnet unscrew bonnet, remove silicone seat cup and wash the parts in warm
soapy water. Clean the inside of the faucet and the connection to the device by using a
small bottle brush.

CAUTION!

Never insert the brush in the assembled faucet since it will puncture the seat cup.

o Never use any kind of inflammables for cleaning purposes as, in case of

reconnection, this increases the risk of fire and explosion.

o In the case of water containing lime, a calcareous layer, which can have an influence

on the heating power of the device appears in the container, particularly at the bottom
of it. It is possible to remove this residue carefully by adding to water a drop of vinegar
or a lime remover available on the market and by boiling this solution for a short time.

- 26 -

Problem

Please

check:

•

o After removing lime rinse the container with clean water.
o After cleaning you should apply a soft, dry cloth in order to wipe dry and polish the

surface.

CAUTION!

Complaints will not be accepted if the device is not decalcified regularly as
described in the instruction manual.

Such complaints are no cases of warranty!

6.3 Safety instructions for maintenance

o Inspect the power cable regularly for damage. Never use the device if the cable is

damaged. If the power cable is damaged, have an authorised service center or
qualified electrician replace it.

o In case of damage or malfunction, please contact your stockist or our customer

service centre.

o Only a qualified technician and using original spare parts and accessories should

carry out repairs and maintenance of the device. Do not attempt to repair the

device yourself.

7. Possible Malfunctions

Control lamp do not flash
up after switching into
temperature stage

Device does not work

• If power plug is plugged in properly

• If the socket works properly ((main) fuse and/or

residual current circuit breaker are OK)

The protection against overheating will be

activated was released because of overheating

If you cannot eliminate the malfunction:

- Disconnect the device from the power supply (pull the plug!),

- Do not open the housing,

- Notify customer service or contact a dealer.

- 27 -

8. Waste disposal

Discarding old devices

At the end of its service life the discarded device has to be disposed in accordance with
the national regulations. It is advisable to contact a company which is specialized in
waste disposal, or just contact the local disposal service in your community.

WARNING!

To exclude any abuse and the dangers involved make the waste device unfit for
use before disposal. For that purpose disconnect device from mains supply and
remove mains connection cable from the device.

NOTE!

For the disposal of the device please consider
and act according to the national and local
rules and regulations.

Bartscher GmbH
Franz-Kleine-Str. 28
D-33154 Salzkotten phone: [phone]
Germany fax: [phone]

- 28 -