Mobile Computing
User Manual
Mobile Computer MC 75Axex-NI and Mobile Computer MC 75A6exHF-NI
Type B7-A27.-..../........
ATEX / IECEx Zone 2 and 22 UL Class I, II, III Division 2
BARTEC GmbH
Contact:
Max-Eyth-Straße
16
Phone.
: +49 7931 597
-0
Service
-
mobilecomputing@bartec.de
97980 Bad
Mergentheim
Fax: +49 7931 597
-
119 Download:
Germany
www.bartec.de/automation
-
download
User Manual - TRANSLATION
Mobile Computer
MC 75Axex-NI and MC 75A6ex HF-NI
Type B7-A27.-…./…….
ATEX Zone 2 and Zone 22
UL Class I, II Division 2
UL Class III
Document No.: B1-A275-7D0002
Status: 27 April 2015 / Revision A
Reservation: Technical data subject to change without notice. Changes, errors and
misprints may not be used as a basis for any claim for damages.
Content Page
Germany 1 - 58
Annex Declaration of Conformity
Certificate of Compliance
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Subject to technical changes.
04/2015
- Empty Page -
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Table of content
Subject to technical changes.
04/2015
1. Basic Safety Instructions.................................................................................................................... 1
1.1 Notes on this manual ................................................................................................................ 1
1.1.1 Languages ................................................................................................................................ 2
1.1.2 Changes to the document ......................................................................................................... 2
1.1.3 Handling the Product................................................................................................................. 2
1.2 Use in Accordance with the Intended Purpose ......................................................................... 2
1.2.1 Exclusive Purpose..................................................................................................................... 2
1.2.2 Improper Use ............................................................................................................................ 2
1.3 Owner’s/Managing Operator’s Obligations ............................................................................... 3
1.4 Safety Instructions..................................................................................................................... 3
1.4.1 General Safety Instructions ....................................................................................................... 3
1.5 Safety Instructions for Operation............................................................................................... 3
1.5.1 Maintenance.............................................................................................................................. 3
1.5.2 Inspection .................................................................................................................................. 4
1.5.3 Repairs ...................................................................................................................................... 4
1.5.4 Commissioning.......................................................................................................................... 4
1.6 Ex Protection Type, Certification and Standards ...................................................................... 4
1.7 Warranty.................................................................................................................................... 4
1.8 Co-applicable documents – Set of documents.......................................................................... 6
1.9 Configuration ............................................................................................................................. 7
2. Product Description ............................................................................................................................ 8
2.1 Definition ................................................................................................................................... 8
2.2 Operation .................................................................................................................................. 9
3. Technical Data ................................................................................................................................... 10
3.1 Explosion protection ................................................................................................................ 10
3.2 Other applicable standards ..................................................................................................... 11
3.3 Features .................................................................................................................................. 12
3.3.1 Performance features.............................................................................................................. 12
3.3.2 Physical features ..................................................................................................................... 12
3.3.3 User environment .................................................................................................................... 13
3.3.4 Application development ......................................................................................................... 13
3.3.5 Voice and data transmission Wireless LAN ............................................................................ 14
3.3.6 Voice and data transmission Wireless WAN ........................................................................... 14
3.3.7 Voice and data transmission Wireless PAN ............................................................................ 14
3.3.8 RFID HF .................................................................................................................................. 15
3.3.9 Decodable barcode types ....................................................................................................... 16
3.4 Battery ..................................................................................................................................... 17
3.5 External interfaces .................................................................................................................. 17
3.6 ATEX product labelling............................................................................................................ 18
3.7 Laser labels ............................................................................................................................. 19
4. Transport and Storage ...................................................................................................................... 20
4.1 Transport ................................................................................................................................. 20
4.2 Storage.................................................................................................................................... 20
5. Commissioning.................................................................................................................................. 21
5.1 Requirements in potentially explosive atmosphere ................................................................. 22
5.2 First steps................................................................................................................................ 23
5.3 Structure.................................................................................................................................. 23
5.4 Handling accessories .............................................................................................................. 24
5.4.1 Insert battery ........................................................................................................................... 25
5.4.2 Charge battery ........................................................................................................................ 26
5.4.3 Remove battery ....................................................................................................................... 28
5.4.4 Charge the battery in charger ................................................................................................. 28
5.4.5 Insert Micro SD card ............................................................................................................... 29
5.4.6 Insert SIM card (MC 75A6ex-NI only) ...................................................................................... 30
5.4.7 Remove/replace screen protector ........................................................................................... 31
Table of content
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Subject to technical changes.
04/2015
5.4.8 Insert SAM card (MC 75A6
ex
HF-NI only) ................................................................................ 32
5.4.9 Remove SAM card (MC 75A6exHF-NI only) ............................................................................ 33
5.5 Connection to a PC ................................................................................................................. 34
5.5.1 Active Sync ............................................................................................................................. 34
5.5.2 Windows Mobile Device Center .............................................................................................. 34
6. Operation............................................................................................................................................ 35
6.1 Final inspection ....................................................................................................................... 35
6.2 Handling .................................................................................................................................. 35
6.3 Care and cleaning ................................................................................................................... 36
6.3.1 Care ....................................................................................................................................... 36
6.3.2 Cleaning .................................................................................................................................. 36
6.3.3 Suitable materials.................................................................................................................... 37
6.4 Operation recommendations and requirements ...................................................................... 38
6.4.1 Basic safety and health protection requirements .................................................................... 38
6.4.2 Equipment of the laser devices ............................................................................................... 41
6.4.3 Restrictions to wireless devices .............................................................................................. 41
6.5 Electromagnetic fields ............................................................................................................. 44
6.5.1 International ............................................................................................................................ 44
6.5.2 Portable devices...................................................................................................................... 44
6.5.3 Handheld devices.................................................................................................................... 44
6.6 Optimise operating times/change energy settings .................................................................. 45
6.6.1 Automatic shutdown in the case of lengthy standby periods .................................................. 45
6.6.2 Change display backlight (increases the operating time of the battery).................................. 45
6.6.3 Change keypad background lighting (increases the operating time of the battery) ................ 46
6.6.4 Switch off radio connections ................................................................................................... 47
6.7 Software versions.................................................................................................................... 47
6.7.1 OEM ....................................................................................................................................... 47
6.7.2 Storage battery........................................................................................................................ 48
6.7.3 Bluetooth ................................................................................................................................. 48
6.7.4 “Fusion”software ..................................................................................................................... 49
6.7.5 “Phone” software ..................................................................................................................... 49
7. Faults and Troubleshooting ............................................................................................................. 50
7.1 Resetting the Mobile Computer MC 75Axex-NI ....................................................................... 50
7.1.1 Windows Mobile 6.x devices ................................................................................................... 50
7.1.2 Perform a warm boot............................................................................................................... 50
7.1.3 Perform a cold start ................................................................................................................. 51
7.1.4 Clean boot ............................................................................................................................... 52
8. Service, Inspection, Repair............................................................................................................... 53
8.1 Service intervals ...................................................................................................................... 53
8.2 Inspection ................................................................................................................................ 53
8.3 Service and repair work .......................................................................................................... 53
8.3.1 Information on sending in for repairs....................................................................................... 54
9. Disposal.............................................................................................................................................. 55
10. Dispatch and Packaging Information .............................................................................................. 55
11. Accessories ....................................................................................................................................... 56
12. Order Numbers .................................................................................................................................. 57
13. Additional Information ...................................................................................................................... 58
13.1 Links ....................................................................................................................................... 58
Appendix - Declaration of conformity
Certificate of compliance
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Basic
Safety Instructions
Subject to technical changes.
04/2015
1/58
1. Basic Safety Instructions
1.1 Notes on this manual
Please read carefully before commissioning the devices.
The user manual is a constituent part of the product. It must be kept in the direct vicinity
of the device and accessible at all times to installation, operating and maintenance
personnel.
It contains important notes, safety instructions and test certificates which are necessary
for perfect functioning when the devices are being operated and handled.
The user manual is written for all people who carry out handling, commissioning,
operation and maintenance work on the product, whereby the directives and standards
applicable to areas with a gas or dust atmosphere (99/92/EC, EN 60079-17, EN 6007919, IEC 60079-17, IEC 60079-19) must be observed when doing such work.
Familiarity with and strict adherence to the safety instructions and warnings in this
manual are essential for safe handling and commissioning. Careful handling and
consistent observation of these instructions can prevent accidents, personal injuries
and damage to property.
The illustrations in these operating instructions serve to make the information and
descriptions more clear. They are not necessarily true to scale and may deviate slightly
from the actual construction of the device.
Safety instructions and warnings are specially highlighted in this manual and marked by
symbols.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in minor
or moderate injury.
ATTENTION
ATTENTION identifies a potentially damaging situation which, if not avoided, could
damage the equipment or something in its environment.
Important instructions and information on effective, economical and environmentally
compatible handling.
Basic
Safety Instructions
Mobile Computer MC 75Axex-NI and MC 75A6ex-HF-NI
Type B7-A27.-…………
2/58
Subject to technical changes.
04/2015
1.1.1 Languages
The original user manual is written in German. All other available languages are
translations of the original user manual.
The user manual is available in German and English. If you require any other languages,
please ask BARTEC or request them when placing the order.
1.1.2 Changes to the document
BARTEC reserves the right to alter the contents of this document without notice. No
guarantee is given for the correctness of the information. In case of doubt, the German
safety instructions shall apply because it is not possible to rule out errors in translation or
in printing. In the event of a legal dispute, the “General Terms and Conditions” of the
BARTEC group shall apply in addition.
The respective up-to-date versions of data sheets, manuals, certificates, EC Declaration
of Conformity may be downloaded at
www.bartec-group.com under products and solutions
in the area “Automatic Technology” or ordered directly from BARTEC GmbH.
1.1.3 Handling the Product
The product described in these user manual has been tested and left the factory in perfect
condition as regards meeting safety requirements. To maintain this condition and ensure
that this product operates perfectly and safely, it may be used only in the manner
described by the manufacturer. Appropriate transportation, suitable storage and careful
operation are also essential for the perfect and safe operation of this product. The Mobile
Computer must be installed properly and securely if it is to work perfectly and correctly.
The safe and perfect mounting of the Mobile Computer is a precondition for faultless and
correct operation.
1.2 Use in Accordance with the Intended Purpose
1.2.1 Exclusive Purpose
The Mobile Computer MC 75Axex-NI is a handheld piece of electrical equipment. It serves
the purpose of the mobile recording, processing and radio transmission of data within
potentially explosive atmospheres.
It is used exclusively in combination with devices which comply with the requirements
placed on the overvoltage category I.
The admissible operating data of the device used must be considered.
1.2.2 Improper Use
Any other use is not in accordance with the intended purpose and can cause damage and
accidents. The manufacturer will not be liable for any use beyond that of its exclusive
intended purpose.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Basic
Safety Instructions
Subject to technical changes.
04/2015
3/58
1.3 Owner’s/Managing Operator’s Obligations
The owner/managing operator undertakes to restrict permission to work with the Mobile
Computers to people who:
are familiar with the basic regulations on safety and accident prevention and have
been instructed in the use of the Mobile Computer;
have read and understood the documentation, the chapter on safety and the
warnings.
The owner/managing operator must check that the safety regulations and accident
prevention rules valid for the respective application are being observed.
1.4 Safety Instructions
1.4.1 General Safety Instructions
Take the device out of the hazardous area before wiping it with a dry cloth or
cleaning it!
Do not open devices in a hazardous area.
The general statutory regulations or directives relating to safety at work, accident
prevention and environmental protection legislation must be observed, e.g. the
German industrial health and safety ordinance (BetrSichV) or the applicable national
ordinances.
In view of the risk of dangerous electrostatic charging, wear appropriate clothing and
footwear.
Avoid the influence of heat that is higher or lower than the specified temperature
range.
Protect the device from external influences! Do not expose the device to any
caustic/aggressive liquids, vapours or mist! In the event of malfunctioning or damage
to the enclosure, take the device out of the potentially explosive area immediately
and bring it to a safe place.
1.5 Safety Instructions for Operation
For electrical systems the relevant installation and operating regulations must be complied
with (e.g. Directive 99/92/EC, Directive 94/9/EC and the national applicable ordinances
EN 60079-14 and the DIN VDE 0100 series)!
The disposal of this equipment must comply with the national regulations on the disposal
of waste.
1.5.1 Maintenance
Regular servicing is not necessary if the equipment is operated correctly in accordance
with the installation instructions and environmental conditions. In this context, please refer
to Chapter "Maintenance, Inspection, Repair".
Basic
Safety Instructions
Mobile Computer MC 75Axex-NI and MC 75A6ex-HF-NI
Type B7-A27.-…………
4/58
Subject to technical changes.
04/2015
1.5.2 Inspection
Under IEC 60079-19 and EN 60079-17, the owner/managing operator of electrical
installations in hazardous areas is obliged to have these installations checked by a
qualified electrician to ensure that they are in a proper condition.
1.5.3 Repairs
Repairs on explosion-protected operating equipment may be done only by authorised
persons working in accordance with the latest developments in technology and using
original spare parts. The applicable regulations must be observed.
1.5.4 Commissioning
Before commissioning, check that all components and documents are there.
1.6 Ex Protection Type, Certification and Standards
Markings specifying Ex protection and certification are put on the device. For Ex
protection markings, see Chapter 3 "Technical Data".
The Mobile Computers conform to Directive 94/9/EC for devices and protective systems
for use to their intended purpose in potentially explosive areas (ATEX Directive). For the
standards conformed to, see Chapter 3 "Technical Data".
1.7 Warranty
WARNING
It is not permissible to make any modifications or implement any conversions unless
the manufacturer gives his approval in writing.
If components other than those specified are used, protection against explosion can no
longer be assured. It cannot be guaranteed that parts procured from other suppliers
have been designed and produced in conformance to safety requirements and with the
necessary stress tolerance.
Contact the manufacturer to obtain approval before making any modifications or
conversions. Use only original spare parts and original expendable parts.
The manufacturer grants a complete warranty only and exclusively for the spare parts
ordered from him, the manufacturer.
As a fundamental rule, our “General Conditions of Sale and Delivery” apply. These are
made available to the owner/managing operator at the latest on formation of a contract.
Guarantee and liability claims for personal injury and damage to property are excluded if
they are due to one or more of the following reasons:
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Basic
Safety Instructions
Subject to technical changes.
04/2015
5/58
Unintended use of the Mobile Computers.
− Incorrect handling, commissioning, operation and servicing.
− Failure to observe the information in the User Manual with respect to transport,
storage, assembly, handling, commissioning, operation and service.
− Independent structural changes.
− Faulty monitoring of parts subject to wear and tear.
− Incorrectly performed repairs.
− Cases of disaster through the impact of foreign bodies and force majeure.
We grant a warranty period of one year starting from the date of delivery from the Bad
Mergentheim factory on the Mobile Computers and their accessories (exception: battery 6
months). This warranty covers all parts of the delivery and shall be restricted to the free
replacement or repair of the defective parts in our Bad Mergentheim factory. For this
purpose, any packaging supplied must be kept where possible. In the case of warranty,
the goods must be returned to us after written agreement. There shall be no claim to
repair at the sight of erection.
The versions, components, monitors and windows shown in this User Manual are merely
examples and may deviate from the actual display.
The information contained herein refers to the explosion-protected version of series
MC 75Ax
ex
-NI.
This User Manual contains all important information on the subject of explosion protection.
The original user manuals and product information of ZEBRA with information on handling
and commissioning are also available. In the case of overlaps, the information in this User
Manual shall take priority and shall supersede the information from ZEBRA.
Basic
Safety Instructions
Mobile Computer MC 75Axex-NI and MC 75A6ex-HF-NI
Type B7-A27.-…………
6/58
Subject to technical changes.
04/2015
1.8 Co-applicable documents – Set of documents
BARTEC
− User Manual to the Mobile Computer series MC 75Ax
ex
-NI – the use of the explosionprotected version of the Mobile Computer series MC 75Axex-NI is described in this
User Manual.
− Technical datasheet for the explosion-protected version of the Mobile Computer
series MC 75Ax
ex
-NI – This technical datasheet contains the most important
explosion-relevant technical data as well as general technical data.
ZEBRA
The set of documentation of the MC75Ax contains information on the respective user
requirements and covers the following:
− Rapid Start Instructions for the MC 75Ax (MC75A Quick Start Guide) – The
commissioning of the Mobile Computer MC75Ax is described in this User Manual.
− User Manual for the Enterprise Digital Assistant MC75Ax (MC75A User Guide) – The
use of the Mobile Computer MC75Ax is described in this User Manual.
− Integration Manual for the Enterprise Digital Assistant MC75Ax (MC75A Integrator
Guide) – The setting up of the Mobile Computer MC75Ax including accessories is
described in this User Manual.
− User Manual for Microsoft® applications for Windows Mobile® 6 for Enterprise
Mobility devices – The use of Microsoft applications is described in this User Manual.
− Manual for Enterprise Mobility applications – The use of example applications is
described in this Manual which have been developed using Enterprise Mobility.
− EMDK Help File (Enterprise Mobility Developer Kit) – This help file contains API
information on the writing of applications.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Basic
Safety Instructions
Subject to technical changes.
04/2015
7/58
1.9 Configuration
This Manual refers to the following configurations:
Configuration Radio link Display Memory Data entry
Operating
system
Keypad
MC 75A0ex-NI
WLAN: 802.11 a/b/g
WPAN: Bluetooth
3.5"-VGA colour display
256 MB RAM/1 GB flash memory
Laser scanner
or
2D Imager
or
1D Laser
scanner and
camera
or
2D Imager and
camera
Windows Mobile® 6.5
Classic
Numerical or QWERTY
MC 75A6ex-NI
WLAN: 802.11 a/b/g
WPAN: Bluetooth
WWAN: HSDPA
GPS: SiRF III
Windows Mobile® 6.5
Professional
MC 75A8ex-NI
WLAN: 802.11a/b/g
WPAN: Bluetooth
WWAN: EvDO *
GPS: SiRF III
Windows Mobile® 6.5
Professional
MC 75A6
ex
HF-
NI
WLAN: 802.11a/b/g
WPAN: Bluetooth
WWAN: HSDPA
GPS: SiRF III
2D Imager
and
camera
and
RFID HF reader
Windows Mobile® 6.5
Professional
Numerical
* Sprint or Verzion
Other specific information on the keypad is provided under Technical Data or in the
ZEBRA documentation.
Product Description
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
8/58
Subject to technical changes.
04/2015
2. Product Description
2.1 Definition
The Mobile Computer MC 75Axex-NI and the Mobile Computer MC 75A6
ex
HF-NI are
3.5G Worldwide Enterprise Digital Assistant (EDA) devices and have been modified by
BARTEC for use in potentially explosive atmospheres of
− ATEX/IECEx Zone 2 and Zone 22 and
− UL Class I, II, Division 2 and
− UL Class III
The extensive communication options which are otherwise standard are therefore
available to the user also in the potentially explosive atmosphere.
Its ergonomic design and ease of operation make it an ideal support to achieve fast data
availability in corporate processes. A keypad in different versions is available for manual
data entry.
Further options for the entry of data are provided by the integrated 1D- or 1D-/2D-Scan
Engine for the entry of barcodes. A 3.2 megapixel camera and/or a RFID HF-Reader
(13.56 MHz) are available for data entry as an option.
Thanks to the ergonomically positioned scan trigger on the MC 75Axex-NI, data may be
easily entered with one hand. Several technologies are available for data communication
with other systems and corporate areas.
− Wireless WAN (WWAN)
− Wireless LAN (WLAN),
− Wireless PAN (WPAN) (Bluetooth)
− IrDA connection
Thanks to the integrated modules in the device, smooth voice and data transmission is
possible with simple integration into the corporate network.
Further advantages of use are its heavy-duty design, easy-to-read 3.5'' VGA colour
display with Touch technology and a high performance lithium-ion battery.
In the MC 75Axex-NI, the PXA320 processor with 806 MHz ensures the fast speed of
processes and the operating system Microsoft® Windows Mobile® 6.5 in connection with
the Enterprise Mobility Developer Kits (EMDK) from ZEBRA ensures simple application
development.
There is an integrated 256 MB RAM in the device for storage and 1 GB Flash to store
user-defined applications and data. BARTEC offers Micro SD memory cards for larger
applications and data volumes.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Product Description
Subject to technical changes.
04/2015
9/58
2.2 Operation
The Mobile Computer MC 75Axex-NI is a handheld electrical device. It serves the
purposes of the mobile entry, processing and radio transmission of data within potentially
explosive atmospheres.
It is used exclusively in combination with devices which comply with the requirements
placed on the overvoltage category I.
The Mobile Computer MC 75Ax
ex
-NI and the Mobile Computer MC 75A6ex HF-NI,
Type B7-A27.-…./…… have been modified for use in the following potentially explosive
atmospheres
− ATEX/IECEx Zone 2 and Zone 22
− UL Class I Division 2 Groups A, B, C and D
− UL Class II Division 2 Groups F and G
− UL Class III
The Mobile Computer MC 75Axex-NI and the Mobile Computer MC 75A6ex HF-NI,
Type B7-A27.-…./…….. may not be used in the following zones:
− ATEX/IECEx Zone 0
− ATEX/IECEx Zone 1 and Zone 21
− UL Class I Division 1
− UL Class II Division 1
Technical Data
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
10/58
Subject to technical changes.
04/2015
3. Technical Data
3.1 Explosion protection
ATEX Zone 2 and Zone 22
Type
MC 75Axex-NI and MC 75A6
ex
HF-NI
B7-A273-…S/W…..
Ex protection
II 3G Ex ic IIC T6 Gc
II 3D Ex ic IIIC T80°C Dc
Certificate
EPS 12 ATEX 1 481 X
Standards
EN 60079-0:2012
EN 60079-11:2012
IECEx
Type
MC 75Axex-NI and MC 75A6
ex
HF-NI
B7-A273-…S/W…..
Ex protection
Ex ic IIC T6 Gc
Ex ic IIIC T80°C Dc
Certificate
IECEx EPS 12.0029X
Standards
IEC 60079-0:2011 Edition 6
IEC 60079-11:2011 Edition 6
ATEX and IECEx Directives
ATEX 94/9/EC
EMV 2004/108/EC
R&TTE 1999/5/EC
RoHS 2002/95/EC
Product labelling
0168
UL Division 2
Type
MC 75Axex-NI
B7-A272-…S/W…..
Ex protection
Class I Division 2 Groups A, B, C and D
Class II Division 2 Groups F and G
Class III
Type
MC 75A6
ex
HF-NI
B7-A271-64CS/WRRAAR00
Designation
Class I Division 2 Groups A, B, C and D
Certificate USA and Canada
E321557
Standards
ISA 12.12.01-2007
UL 60950-1 1st edition
C22.2 No. 213-M1987
C22.2 No. 60950-1-03 1st edition
Further approvals
China
CNEx12.1429X
South Africa
S-XPL/13.0306X
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Technical Data
Subject to technical changes.
04/2015
11/58
3.2 Other applicable standards
Electrical safety
EN 60950-1:2006+A11:2009
Setting up of IT safety Part 1. General requirements
IEC 60950-1:2005 Ed. 2.0
EMC
GSM Digital Cellular Radio EN 301 489-1 V1.8.1, EN301 489-7 V1.3.1
UMTS Digital Cellular EN 301 489-1 V1.8.1, EN 301 489-24 V1.4.1
Radio Wideband Systems EN 301 489-1 V1.8.1, EN 301 489-17 V2.1.1
Short Range Devices (SRD) EN 301 489-1 V1.8.1, EN 301 489-3 V1.4.1
IT Emissions EN55022:2006 +A1:2007 (Class B)
Harmonic Current Emissions EN 61000-3-2:2006 (Class A)
Voltage Fluctuation & Flicker EN 61000-3-3:2008
Radio Frequency Devices 47 CFR Part 15, Subpart B, Class B
Digital Apparatus ICES 003 Issue 4, Class B
Radio
GSM Essential Requirements EN 301 511: V9.0.2
GSM Conformance Specification 3GPP TS 51.010-1 v.4.9.0 (GSM 11.10-1)
UMTS Essential Requirements
Spurious Emissions
EN 301 908-1 V3.2.1
UMTS Essential Requirements
Transmitter / Receiver
EN 301 908-2 V3.2.1
UMTS RF 3GPP TS 34.121
UMTS Protocol 3GPP TS 34.123
Wideband 2.4 GHz Systems EN 300 328 V1.7.1
Broadband Radio Access (5 GHz) EN 301 893 V1.5.1
Short Range devices (1-40 GHz) EN 300 440-2 V1.3.1
SAR
EN 50360:2001
(Max average 10g SAR 0.992 W/Kg)
EN 50371:2002
EN 62311:2008
FCC 47CFR Part2; OET Bulletin 65c
RSS 102 Issue 3
Laser Products
IEC Class 2 Laser Product
EN 60825-1:2007
IEC 60825-1:2007
21CFR1040.10 Class IIa or II
Technical Data
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
12/58
Subject to technical changes.
04/2015
3.3 Features
3.3.1 Performance features
CPU
PXA320 Processor with 806 MHz
Operating system
MC 75A0
ex
-NI
MC 75A6ex-NI, MC 75A8ex-NI
Windows Mobile 6.5
Classic
Professional
Memory
256 MB RAM; 1 GB Flash
Extension slot
Micro SD slot with SDHC support
(up to 32 GB)
Optionally extendable with Micro SD card:
1 GB Order number 17-C1Z0-0007
2 GB Order number 17-C1Z0-0008
4 GB Order number 17-28BE-F006/000A
8 GB Order number 17-28BE-F006/000B
Interfaces
RS232
USB
3.3.2 Physical features
Dimensions in mm/inch
WWAN:
WLAN:
RFID:
Height x width x depth
178 x 84 x 44 mm 7 x 3.3 x 1.7 inch
152 x 84 x 44 mm 6 x 3.3 x 1.7 inch
178 x 84 x 48 mm 7 x 3.3 x 1.9 inch
Weight including battery 1.5x
WWAN:
WLAN:
RFID:
Depends on version and configuration
approx. 423 g approx. 15 oz
approx. 398 g approx. 14 oz
approx. 467 g approx 16.5 oz
Display
Transflective 3.5"-VGA colour display
640 x 480 pixels
Touchscreen
Analogue-resistive glass touchscreen
Background lighting
LED technology
Network connections
Ethernet (via charge station);
Full-Speed USB, Host or Client
Notification
Vibration function and LED
Keypad versions
Numerical, QWERTY
Audio
VoWWAN; VoWLAN,
compatible with TEAM Express,
Support of hardwired and wireless headsets
(Bluetooth), mode for headset, earphones and
hands-free set
Interactive sensor technology
Three-axes accelerometer for motion sensor
application for dynamic screen orientation, power
monitoring and recognition of free fall
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Technical Data
Subject to technical changes.
04/2015
13/58
3.3.3 User environment
Operating temperature
-10 °C to +50 °C +14 °F to +122 °F
Operating temperature
during charging
0 °C to +40 °C +32 °F to +104 °F
Storage temperature
(without battery)
-40 °C to +70 °C -40 °F to +158 °F
Air humidity
5 % to 95 % (non-condensing)
Class of protection (EN 60529)
IP 54
3.3.4 Application development
PSDK (Platform Software Development Kit) and EMDK (Enterprise Mobility Developer
Kit) is available via the ZEBRA Website under SUPPORT & DOWNLOADS.
Available for
− C
− Java
− .Net
Browser support:
Pocket Browser or “RhoMobile Suite” for application development is available via the
ZEBRA Website under PRODUCTS / SOFTWARE / RhoMobile.
RhoMobile Suite Toolkit
consists of:
− RhoMobile Suite
− RhoConnect
− RhoElements
− RhoStudio
Technology-independent applications are prepared
using this toolkit. Device type, operating system
and screen size no longer play a role.
RhoMobile applications run simply on all popular
mobile devices used in your company.
Further applications are
available from ZEBRA, e.g.
HF RFID API
− with demo for application development.
Rem Capture
− for the processing of registration files.
Application Launcher
− for the classification of applications in categories
and access regulation for individual applications
or operating system.
Data Wedge
− Barcodes in applications can be read such as
Excel or Word using.
AppCenter
− to define access regulations for the applications.
Technical Data
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
14/58
Subject to technical changes.
04/2015
3.3.5 Voice and data transmission Wireless LAN
WLAN radio module
Radio standard
Tri Mode IEEE 802.11a/b/g
Data rate
IEEE802.11a: up to 54 Mbit/sec.
IEEE802.11b: up to 11 Mbit/sec.
IEEE802.11g: up to 54 Mbit/sec.
Frequency range
(country-dependent)
IEEE802.11a: 5 GHz
IEEE802.11b: 2.4 GHz
IEEE802.11g 2.4 GHz
Operating channels
IEEE802.11a
IEEE802.11b/g
Channel 8 - 165 5040 MHz - 5825 MHz
Channel 1 - 13 2412 MHz - 2472 MHz
Channel 14 2484 MHz Japan only
The actual operating channels and frequencies are
subject to the applicable rules and the certification
authorities
Safety
WPA2, WEP (40 or 128 Bit), TKIP, TLS, TTLS (MSCHAP), TTLS (MS-CHAP Ver. 2), TTLS (CHAP),
TTLS-MD5, TTLS PAP, PEAP TLS, PEAP (MSCHAP v2), AES, LEAP, CCXv4 Certification, FIPS140-2 Certification
Spread procedure
DSSS (Direct Sequence Spread Spectrum) and
Orthogonal Frequency Division Multiplexing
Voice communication
Voice-over-IP integrated and prepared
(P2P, PBX, PTT), WLAN according to IEEE 802.11
a/b/g,
WI-Fi™ Certification and DSSS
Antenna
internal
3.3.6 Voice and data transmission Wireless WAN
WWAN radio module
GSM
optional
HSDPA (850, 900, 1800, 1900 and 2100 MHz)
CDMA
optional
EVDO Rev. A (800 and 1900 MHz);
Verizon or Spirit
GPS
(only MC 75A6ex-NI and
MC 75A8ex-NI)
Integrated independent or Assisted-GPS
(A-GPS) via SUPL, chip set SiRFstarIII GSC 3f/LP
Antenna
external
3.3.7 Voice and data transmission Wireless PAN
Bluetooth Class II, Version 2.1 with EDR
Maximum data rate Up to 2.1 Mbit/s
Antenna
Internal chip antenna
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Technical Data
Subject to technical changes.
04/2015
15/58
3.3.8 RFID HF
RFID Radio 13.56 MHz
Read range 0 to 5 cm (0 to 1.96 inch)
SAM card ISO 7816 in line with encryption
Supported RFID types
ISO 14443-A:
MIFARE™ (Classic, UltraLight,DESFire)
ISO 14443-B:
Calypso® (GTML, GTML2, CD21, CD Light, CDS3,
CD97, CD97BX, TanGO, Celego-Citi, CT2000), ASK
CTS256 and CTS512, STMicroelectronics SRI
FeliCa®
ISO15693:
NXP I.Code SLI, TI Tag-it
3.3.8.1 Colour camera (optional)
Resolution
3.2 megapixel
Exposure
Flash (can be controlled by user)
Object lens
Autofocus
3.3.8.2 SE950 1D Standard Range Scan Engine
Range at 100 % UPC-A
approx. 60 cm
Resolution
4 mil minimum width
Roll
± 35° from the vertical
Pitch angle
± 65° from the starting position
Skew tolerance
± 50° from the starting position
Ambient light
107.640 lux
Scan rate
104 (± 12) scans/sec. (bi-directional)
Scan angle
47° ± 3 ° standard
35° ± 3° reduced
Laser power
1.0 mW nominal value
Technical Data
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
16/58
Subject to technical changes.
04/2015
3.3.8.3 SE4500 1D/2D Imager Engine
Reader range
Approx. 6 cm to 50 cm
approx. 2.3 inch to 19 inch
Focus distance
From centre of the scanner window
SR --- 19 cm
Resolution
752 x 480 Pixel HxV (grey phase)
Roll
360°
Pitch angle
± 60° from the starting position
Skew tolerance
± 60° from the starting position
Ambient light
96.900 lux
Aiming element (VLD)
655 Nm ± 10 nm
Illumination element (LED)
625 Nm ± 5 nm LEDs (2x)
Field of view
Horizontal 40 °
Vertical 25 °
3.3.9 Decodable barcode types
SE950
1D-Standard Range Scan Engine
SE4400
1D/2D Imager Engine
Only decodable by 2D Imager
1D Codes 2D Codes
Code 11 Interleaved 2 aus 5 Aztec Micro PDF-417
Code 39 MSI Australian 4-state Micro QR
Code 93 RSS-14 Canadian 4-state Maxi Code
Code 128 RSS-Limited Composite AB PDF-417
Codabar RSS-Expanded Composite C QR Code
Coupon code Trioptic 39 Data Matrix TLC39
Chinese 2 from 5 UPCA Dutch Kix UK 4-state
Discreet 2 from 5 UPCE Japanese 4-state US Planet
EAN-8 UPC/EAN add-ons Macro PDF-417 US Postnet
EAN-13 Webcode
(Macro) Micro
PDF-417
USPS 4-state
(US4CB)
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Technical Data
Subject to technical changes.
04/2015
17/58
3.4 Battery
Battery
− Type B7-A2Z0-0007
− Type B7-A2Z0-0008
(only rechargeable in safe range)
Lithium-ion battery 3.7 V/3600 mAh
Lithium-ion battery 3.7 V/4800 mAh
Operating temperature
− During charging
− During discharging
0 °C to +40 °C +32 °F to 104 °F
-10 °C to +50 °C +14 °F to 122 °F
Storage temperature -20 °C to +50 °C -4 °F to 122 °F
Relative air humidity 20 % - 95 % (non-condensing)
Backup battery Ni-MH battery 2.4 V/15 mAh (rechargeable)
Integrated in the device and only replaceable in the
factory.
Battery performance
Standby time
Talk time
depends on the device settings
approx. 150 hours
approx. 5 hours
3.5 External interfaces
Restrictions:
− The 16-pole data interface should only be used outside the potentially explosive
atmosphere and exclusively with the devices stated by the manufacturer!
− The headset connection should only be used outside the potentially explosive
atmosphere and exclusively with the devices stated by the manufacturer!
PIN Description PIN Description
1 Power GND 9 RS232_TxD
2 Cradle_Detect 10 RS232_RxD
3 RS232_DCD/Trigger 11 RS232_RTS
4 USB_D- 12 RS232_CTS
5 USB_D+ 13 RS232_DTR
6 USB_GND 14 RS232_DSR
7 USB_Vbus 15 External_5.0V_Out
8 USB_ID 16 External_DC_In_5.4V
Technical Data
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
18/58
Subject to technical changes.
04/2015
3.6 ATEX product labelling
Labelling plate ATEX
Labelling plate UL
Warning: laser
See also Chapter 3.7
Type plate ATEX and UL
Warning: battery for ATEX
Not for UL
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Technical Data
Subject to technical changes.
04/2015
19/58
3.7 Laser labels
In compliance with IEC 60825 and EN 60825, Clause 5 the following information is
provided:
DEUTSCH
KLASSE 1 KLASSE 1 LASER PRODUKT
KLASSE 2 LASERLICHT
NICHT IN DEN LASERSTRAHL SEHEN
KLASSE 2 LASER PRODUKT
ENGLISH
CLASS 1 CLASS 1 LASER PRODUCT
CLASS 2 LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
FRENCH / FRANÇAIS
CLASSE 1 PRODUIT LASER DE CLASSE 1
CLASSE 2 LUMIERE LASER NE PAS REGARDER LE
RAYON FIXEMENT
PRODUIT LASER DE CLASSE 2
ITALIAN / ITALIANO
CLASSE 1 PRODOTTO AL LASER DI CLASSE 1
CLASSE 2 LUCE LASER
NON FISSARE IL RAGGIOPRODOTTO
AL LASER DI CLASSE 2
PORTUGUESE / PORTUGUÊS
CLASSE 1 PRODUTO LASER DA CLASSE 1
CLASSE 2 LUZ DE LASER NÃO FIXAR O RAIO
LUMINOSO
PRODUTO LASER DA CLASSE 2
DUTCH / NEDERLANDS
KLASSE 1 KLASSE-1 LASERPRODUKT
KLASSE 2 LASERLICHT
NIET IN STRAAL STAREN
KLASSE-2 LASERPRODUKT
DANISH / DANSK
KLASSE 1 KLASSE 1 LASERPRODUKT
KLASSE 2 LASERLYF
SE IKKE IND I STRÅLEN
KLASSE 2 LASERPRODUKT
NORWEGIAN / NORSK
KLASSE 1 LASERPRODUKT, KLASSE 1
KLASSE 2 LASERLYS IKKE STIRR INN I
LYSSTRÅLEN
LASERPRODUKT, KLASSE 2
FINNISH / SUOMI
LUOKKA 1 LUOKKA 1 LASERTUOTE
LUOKKA 2 LASERVALO
ÄLÄ TUIJOTA SÄDETTÄ
LUOKKA 2 LASERTUOTE
Transport and Storage
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
20/58
Subject to technical changes.
04/2015
4. Transport and Storage
4.1 Transport
Report any transport damage or incomplete deliveries immediately after receipt in
writing to the forwarding company and BARTEC GmbH.
Any damage caused through incorrect storage shall not be covered by the warranty
provisions of BARTEC GmbH.
4.2 Storage
ATTENTION
Property damage through incorrect storage!
Observe storage temperatures.
Keep humidity away from the Mobile Computers.
Additional information on the batteries
The batteries of BARTEC (Type B7-A2Z0-….) are developed and manufactured in
accordance with the highest industrial standards. The operating time or storage period of
a battery is restricted, however. The actual life of a battery is influenced by different
factors, e.g. hot, cold, rough operating environment and falling from a great height. If a
battery is kept longer than six months, the performance may be impaired on a permanent
basis. Keep the batteries in a dry, cool place. For longer periods of storage, remove the
batteries from the device to prevent self-discharge, rusting of metallic parts and the
escape of electrolyte.
Batteries kept for the duration of 6 months or longer should be charged and then
discharged again at least every 3 months. If electrolyte has escaped, do not touch the
areas affected and dispose of the batteries as prescribed. Replace the battery if the
operating time has shortened considerably.
The standard warranty period for all BARTEC batteries is 6 months, whereby it is
irrelevant whether the battery was acquired separately or was contained in the scope of
delivery of the MC 75A
ex
-NI.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Commissioning
Subject to technical changes.
04/2015
21/58
5. Commissioning
Before you assemble the device, make sure that all components and documents exist.
Scope of delivery:
1 x MC 75Axex-NI
1 x Lithium-ion battery
1 x Battery cover
1 x Screen protector
1 x Stylus
1 x User Manual
Optional:
Authorised accessories from BARTEC:
− Micro SD card
− Replacement stylus
− Battery 1.5x and 2.5x
− Battery cover 1.5x and 2.5x
− Charging station
− Cradle
− Screen protector
Accessories:
− SIM card
− SAM card (for MC 75A6
ex
HF-NI only)
DANGER
Avoid electrostatic charging in potentially explosive atmosphere.
Risk of fatal injury in an explosive atmosphere!
Do not dry wipe or clean the devices.
Wear suitable clothing and shoes.
Do not use rubber gloves or similar.
DANGER
Unintended use endangers explosion protection.
Risk of fatal injury in an explosive atmosphere!
Do not make any changes to the Mobile Computer.
In the case of functional disturbances or damage to the enclosure, the device
should be removed immediately from the potentially explosive atmosphere to a
safe place. Remove battery to decommission the device!
Do not use any battery replicas or batteries from other manufacturers.
Commissioning
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
22/58
Subject to technical changes.
04/2015
5.1 Requirements in potentially explosive atmosphere
Mobile Computer
1. The Mobile Computer may not be opened.
2. Do not use, swap or replace any non-specified components.
3. Do not retrofit any components to the internal plugs or slots.
4. Protect the Mobile Computer from impact!
5. Do not expose the Mobile Computer to caustic/aggressive liquids, vapours, mists!
6. Avoid the impact of moisture outside the specifications.
7. Avoid thermal impact outside the specified temperature range.
8. Use the 16-pole data interface only outside the potentially explosive atmosphere and
exclusively with the devices specified by the manufacturer!
9. Use the headset connection only outside the potentially explosive atmosphere and
exclusively with the devices specified by the manufacturer!
Battery
1. The battery may not be opened.
2. Only charge the battery outside the potentially explosive atmosphere.
3. Only use the battery for the purpose listed in this User Manual. Is only suitable for
the Mobile Computer MC 75Axex-NI (Type B7-A27.-…./……..).
4. There is a danger of burning if used incorrectly. Do not expose the battery to
temperatures of more than +50 °C (122 °F).
5. Battery acid may escape from the cells and cause burning in the case of damage.
6. Defective batteries must be disposed of immediately, whereby the provisions on
battery disposal applicable in the respective region must be observed.
7. The battery may explode if it catches fire!
8. Do not short circuit the battery!
Accessories
1. Only install or replace accessories outside the potentially explosive atmosphere.
2. Use accessories exclusively which have been tested or certified by BARTEC for this
purpose.
3. The end user can replace the Micro SD card, SIM card or SAM card (only for
MC 75A6ex HF-NI) himself.
4. The end user cannot replace the keypad himself. The devices are adjusted to the
selected keypad version.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Commissioning
Subject to technical changes.
04/2015
23/58
5.2 First steps
Unpack the Mobile Computer.
Insert the battery into the Mobile Computer.
Charge the battery on the cradle.
Switch on the Mobile Computer.
Optional:
Charge the battery in a charger.
Insert a Micro SD card.
Insert a SIM card (only possible with MC 75A6
ex
-NI).
Insert a SAM card (only possible with MC75A6
ex
HF-NI).
The individual steps are explained on the following pages.
5.3 Structure
Commissioning
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
24/58
Subject to technical changes.
04/2015
5.4 Handling accessories
DANGER
Non-certified accessories endanger explosion protection.
Risk of fatal injury in an explosive atmosphere!
Only use original accessories from BARTEC / ZEBRA.
Only permitted outside the potentially explosive atmosphere:
Charge battery.
Insert/replace SIM card (MC75A6
ex
-NI only).
Insert/replace Micro SD card.
Insert/replace SAM card (MC75Ax
ex
HF-NI only).
Remove/replace screen protector.
Further information is also provided by the ZEBRA documentation.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Commissioning
Subject to technical changes.
04/2015
25/58
5.4.1 Insert battery
Depending on configuration, the MC 75Axex-NI is supplied with a 3600 mAh or 4800 mAh
battery.
Type Order number Charge time
Battery 1.5x
Lithium-ion battery 3.7 V /3800 mAh
Accompanying battery cover: ATEX
UL
B7-A2Z0-0007
03-9860-0082
03-9860-0072
Less than 8 hours
Battery 2.5x
Lithium-ion battery 3.7 V /4800 mAh
Accompanying battery cover: ATEX
UL
B7-A2Z0-0008
03-9860-0083
03-9860-0081
Less than 8 hours
Work steps:
1. Only charge, install or replace the battery outside the potentially explosive
atmosphere.
2. Use batteries exclusively which have been tested or certified by BARTEC for this
purpose.
3. Insert the battery, top first, into the battery compartment on the rear side of the
Mobile Computers MC 75Axex-NI.
4. Ensure that the charge contacts of the battery agree with the charge contacts in the
battery compartment.
5. Press the battery down into the battery compartment until the battery release latch
snaps into place.
6. With the battery cover latches open, insert the cover, bottom first, then press down
on the top of the cover.
7. Close the battery cover latches on either side of the battery cover.
8. Feed the handstrap through the slot provided for it and pull the handstrap fastener
downwards.
9. Secure the handstrap.
Commissioning
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
26/58
Subject to technical changes.
04/2015
5.4.2 Charge battery
1. Place the Mobile Computer with battery inserted into the cradle.
2. Connect the charge cable of the cradle with a suitable power ssource.
3. The charge process starts automatically and is shown by an orange flashing light
at the LED. The battery charges completely in less than 8 hours.
4. The charge process of the battery is completed once the LED permanently lights
up orange.
Single Slot USB Cradle Set
(without USB cable and appliance coupler)
03-9015-0015
4-slot cradle set
(without applicance coupler)
03-9015-0014
The charge process of MC 75Axex-NI is activated and deactivated at short time intervals
to keep battery temperature within the admissible range.
The MC 75Axex-NI shows by LED when the charge process has been deactivated due
to high temperature.
Further information is provided by the ZEBRA documentation.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Commissioning
Subject to technical changes.
04/2015
27/58
LED charge status Meaning
Slow orange flashing light
(1 flash signal every 2 sec.)
The MC 75Axex-NI is being charged.
Orange coloured permanent
light
The charge process has been completed.
N.B.:
When the battery is inserted into the MC 75AxexNI for the first time, the yellow LED display lights
up once if the charge status of the battery is too
low or the battery is not inserted correctly.
Fast orange flashing light
(2 flash signals every sec.)
Charge error!
Possible causes:
− The temperature is too high or too low.
− The charge process takes too long without
having been completed (usually 8 hours).
Off No charge process
− The MC 75Ax
ex
-NI is not charging.
− The MC 75Ax
ex
-NI is not inserted correctly in
the cradle.
− The MC 75Ax
ex
-NI is not connected with any
power source.
− The charger/cradle is not powered.
Individual orange flash signal
(if power button has been
pressed)
The battery is discharged.
Orange flashing light (if power
button has been pressed)
The battery is overheated.
The MC 75Axex-NI is equipped with a backup battery which is automatically charged if
the main battery is completely charged.
When the MC 75Axex-NI is put into operation for the first time, the backup battery needs
approximately 36 hours to be fully charged. This is also the case even if the main
battery has been removed for several hours, causing the backup battery to discharge.
The backup battery ensures that the data in the main memory are maintained for at
least 15 minutes after the main battery of the MC 75Axex-NI has been removed. When
the MC 75Axex-NI reaches a low state of charge, the data are maintained in the main
memory for at least 48 hours as a result of the combination of main battery and backup
battery.
Further information is provided in the ZEBRA documentation.
Commissioning
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
28/58
Subject to technical changes.
04/2015
5.4.3 Remove battery
Work steps
1. Only remove the battery outside the potentially explosive atmosphere .
2. Press the red “ON/OFF” button to switch off the Mobile Computer.
3. Wait until the red status LED lights up and goes out again.
4. Press the battery release latch on the buttom of the battery to unlook.
5. Lift the top of the battery cover and remove the cover.
6. Press the battery down into the battery compartment until the battery release latch
snaps into place.
7. Remove the battery.
5.4.4 Charge the battery in charger
Work steps
1. Only charge the battery outside the potentially explosive atmosphere.
2. Insert the battery into the single slot cradle.
3. Charging starts automatically when connected to a power source.
4. The battery is usually completely charged in less than 8 hours.
5. Charging for battery is completed when the LED lights up permanently.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Commissioning
Subject to technical changes.
04/2015
29/58
5.4.5 Insert Micro SD card
ATTENTION
Damage to the SD card through electrostatic discharges!
Use an antistatic base.
Ensure that the operator is correctly earthed.
Work steps
1. Only install or replace the Micro SD card outside the potentially explosive
atmosphere.
2. Only use Micro SD cards which have been tested and certified by BARTEC for this
purpose.
3. Press the red “ON/OFF” button to switch off the Mobile Computer.
4. Unlook the two screws of the side memory card cover.
5. Ensure that the card contacts are facing up.
6. Insert the Micro SD card until you feel a click.
7. Tigthen both screws of the memory card cover.
8. Press the red “ON/OFF” button on the Mobile Computer.
9. In the File Explorer or settings of the memory, check that the Micro SD card has
been recognised.
Commissioning
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
30/58
Subject to technical changes.
04/2015
5.4.6 Insert SIM card (MC 75A6
ex
-NI only)
The use of SIM cards can result in additional costs, which must be borne by the
purchaser (customer) of the devices. The seller will not cover any additional costs
incurred when these devices are used. Nor will the seller pay any other costs incurred
when this device is used in one of the customer´s applications.
Work steps
The slot for the SIM card is located beneath the battery.
1. Only install or replace the SIM card outside the potentially explosive atmosphere.
2. Press the red “ON/OFF” button to switch off the Mobile Computer.
3. Remove the battery.
4. Slide the SIM card cover to the left to unlook.
5. Lift the SIM card cover using the stylus tip.
6. Insert the SIM card with the cut edge of the card facing out and the contacts facing
down.
7. Lower the SIM card cover and using the stylus tip, slide in place.
8. Insert the battery.
9. Close the battery cover.
After installing the MC 75Axex-NI for the first time or after replacing the SIM card:
1. ress the red “ON/OFF” button to switch off the Mobile Computer.
2. On the Today screen, tap the Antenna icon.
3. Select Wireless Manager in the dialog box and check that the phone function is
activated.
4. Press the red “ON/OFF” button on the MC 75Ax
ex
-NI to set the MC 75Axex-NI to
standby mode.
5. Perform a warm boot.
6. Make a call to verify cellular connection.
The ZEBRA User Manual on the Integration of the Mobile Computers of MC 75Ax
(MC75A User Guide) contains detailed information on WWAN activation and the
settings.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Commissioning
Subject to technical changes.
04/2015
31/58
5.4.7 Remove/replace screen protector
The screen protector protects the touchscreen and improves the user friendliness of the
device. With its relatively hard surface, the screen protector offers a mechanical protection
against scratches for example and reduces disturbing light reflections.
ATTENTION
Incorrect handling may cause damage to property!
Use a screen protector so as not to impair the device warranty.
Only use screen protector (Type B7-A2Z0-0016) from BARTEC.
Observe the installation instructions for the screen protector.
Do not use any sharp objects to remove the screen protector!
Work steps
1. Only remove or replace the screen protector outside the potentially explosive
atmosphere.
2. Lift a corner of the screen protector and remove it from the display.
3. Attach the screen protector in accordance with the “Screen protector installation
instructions”.
Commissioning
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
32/58
Subject to technical changes.
04/2015
5.4.8 Insert SAM card (MC 75A6
ex
HF-NI only)
The provider’s documentation has further information on SAM cards.
ATTENTION
Damage to the SD card through electrostatic discharges!
Use an antistatic base.
Ensure that the operator is correctly earthed.
Work steps
1. Only insert the SAM card outside the potentially explosive atmosphere.
2. Only use SAM cards which have been specified by ZEBRA for this purpose.
3. Press the red “ON/OFF” button to switch off the Mobile Computer.
4. Remove the four screws of the cover plate/RFID antenna antenna using a torx (T5)
screwdriver.
5. Lift RFID anmtenna from the reverse side of the enclosure and remove.
6. Open the cover of the SAM card.
7. Insert the SAM card into the opening with the contacts facing down.
8. Close the cover of the SAM card.
9. Click-in the RFID antenna on the reverse side of the enclosure.
10. Tighten the four screws using a torx (T5) screwdriver.
11. Perform a warm boot.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Commissioning
Subject to technical changes.
04/2015
33/58
5.4.9 Remove SAM card (MC 75A6
ex
HF-NI only)
Work steps
1. Only remove the SAM card outside the potentially explosive atmosphere.
2. Press the red “ON/OFF” button to switch off the Mobile Computer.
3. Remove the four screws of the cover plate/RFID antenna using a torx (T5)
screwdriver.
4. Lift RFID antenna from the reverse side of the enclosure and remove.
5. Open the cover of the SAM card and remove the SAM card.
6. Close the cover of the SAM card.
7. Click-in the RFID antenna on the reverse side of the enclosure.
8. Tighten the four screws using a torx (T5) screwdriver.
9. Perform warm boot.
Commissioning
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
34/58
Subject to technical changes.
04/2015
5.5 Connection to a PC
The MC 75Axex-NI series is supplied with the Microsoft WM 6.5 or higher operating
system. Microsoft provides software free of charge for connection to a PC for
synchronisation, installation and data exchange.
5.5.1 Active Sync
It is recommended to install ActiveSync (Version 4.5 or higher) on the host computer for
communication with different computers installed under Windows XP or earlier
operating systems.
ActiveSync synchronises the information from the Mobile Computer with the host
computer. Changes made on the Mobile Computer or the host computer exist on both
devices after synchronisation.
ActiveSync is available for download as freeware at www.microsoft.com.
Supporting operating system: Windows XP or earlier operating systems
More information on ActiveSync is available in the ZEBRA Integration Manual or on the
Microsoft website.
5.5.2 Windows Mobile Device Center
It is recommended to install the Windows Mobile Device Center on the host computer
for the communication with different host computers installed under Windows Vista,
Windows 7 or Windows 8.
The Windows Mobile Device Center synchronises the data from the Mobile Computer
with the host computer. Changes made on the Mobile Computer or the host computer
exist on both devices after synchronisation.
The Windows Mobile Device Center is available for download as freeware at
www.microsoft.com.
Supporting operating systems: Windows Vista, Windows 7 or Windows 8
More information on Windows Mobile Device Center is available in the ZEBRA Integration
Manual or on the Microsoft website.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Operation
Subject to technical changes.
06/2013
35/58
6. Operation
The operator using an electric system in a potentially explosive environment must keep
the accompanying operation equipment in a good condition, operate and monitor it
correctly and conduct the requisite services and repairs. Before commissioning the
devices, it must be checked that all components and documents are available.
6.1 Final inspection
The following aspects must be checked before putting the device into operation:
Is there any damage to the display, scanner window or enclosure?
Is the battery used certified?
Is the battery compartment cover closed?
Does the screen protector (if used) have the requisite certification?
Is the Micro SD card specified for the MC 75Ax
ex
-NI?
6.2 Handling
Optimum standby position
Right:
The Mobile Computer is protected from damage.
Wrong:
The Mobile Computer can be damaged by objects on the surface or may fall down.
Operation
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
36/58
Subject to technical changes.
04/2015
6.3 Care and cleaning
We recommend that the devices be cleaned regularly depending on use and also treated
with care to ensure smooth and trouble-free operation.
6.3.1 Care
Recommendation
Display
− Only use with supplied stylus for the touchscreen
− Use screen protector
− Use a soft cloth to clean and do not use aggressive cleaners
Enclosure
− Protect device from impacts
− Do not expose to extreme load, e.g. strong knocks and falling
from great heights
Environment
− Do not expose to extreme temperatures and
− Do not leave in dirty, moist or wet environment
Battery
− Change regularly
− Discharge and charge regularly (every 3 months)
6.3.2 Cleaning
DANGER
Risk of fatal injury in an explosive atmosphere!
Only clean the devices and the accessories outside the potentially explosive
atmosphere.
ATTENTION
Devices and accessories can be destroyed if handled incorrectly.
The following precautionary measures should be taken for your own safety and
to ensure the operational safety of the device:
Generally separate the charger from the power supply.
Only clean the cradle contacts if the battery has been removed.
There should be no residue, e.g. fluff on the contacts.
There should be no moisture residue on the contacts.
Heed the safety precautions when drying with compressed air.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Operation
Subject to technical changes.
04/2015
37/58
6.3.3 Suitable materials
− Alcohol cleaning cloths
− Lens cleaning cloths
− Cotton swabs
− Isopropanol
− Compressed air spray with tube
Suitable cleaning agent
Enclosure − With alcohol cleaning cloths
Keys and intermediate spaces − With alcohol cleaning cloths
Screen − With alcohol cleaning cloths
Avoid collections of fluid and rub with smooth cloths
Scanner window − Cleaning agent for optical devices
Battery contacts
Remove the battery from the device to clean.
− Soak the cotton swabs in an alcohol solution to remove all grease
and dirt deposits on the contacts.
− Repeat cleaning several times
Before replacing the battery, the contacts must be completely dry and
no fluff should remain.
Cradle contacts
To clean the cradle contacts, remove the battery from the device and
close the battery compartment.
− Soak the cotton swabs in an alcohol solution to remove all grease
and dirt deposits on the contacts.
− Repeat cleaning several times
Before the device is replaced in the cradle, the cradle contacts must be
completely dry and no fluff should remain.
Charger plug-in connector
Separate the charger from the power supply to clean the charger
contacts.
− Soak the Q-Tips in an alcohol solution to remove all grease and dirt
deposits on the contacts.
− Repeat cleaning several times
Before the charger is reconnected to the power supply, the contacts
must be completely dry and no fluff should remain.
Operation
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
38/58
Subject to technical changes.
04/2015
6.4 Operation recommendations and requirements
6.4.1 Basic safety and health protection requirements
Consult your local health and safety officer to ensure that you are acquainted with the
safety regulations in your company which serve to protect employees at the work place.
6.4.1.1 Ergonomic recommendation
The following recommendations should be considered for everyday work at the
workplace:
− Avoid one-sided, constantly repetitive movements.
− Body posture should be as neutral as possible.
− Avoid exercising great force.
− Keep objects which are used frequently within a functional distance.
− Adjust the working height to the body height and type of work.
− Erect objects without vibration.
− Avoid the exercise of direct pressure.
− Ensure that tables and chairs are adjustable.
− There must be sufficient room for body movements.
− Ensure that the working environment is suitable.
− Optimise workflows.
− Alternate between the left and right hand as frequently as possible when conducting
repetitive tasks.
6.4.1.2 Vehicle installation
RF signals may impair incorrectly installed or inadequately shielded electronic systems in
vehicles (including safety systems). If you have any questions on your vehicle, get in
touch with the manufacturer or a sales person. You can also learn from the manufacturer
whether additional equipment has been fitted to the vehicle. An airbag has a strong
impact. Do NOT place objects, such as installed or portable radio equipment, in the area
above the airbag or in the area of deployment of the airbag. If the radio equipment was
not correctly installed in the vehicle, severe injuries may result if the airbag is triggered.
Position the device within good range. Ensure that you have access to the device without
having to take your eye off the road.
It is not permitted to connect a warning device which leads to horn sounds or light
signals when receiving a call in road traffic.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Operation
Subject to technical changes.
04/2015
39/58
Road traffic safety
Do not take any notes and do not use the device when driving. Making a list of to-do’s or
browsing through the address book when driving has a negative influence on safe driving.
When driving on the roads, you must primarily think of your safety and that of the other
road users. You should therefore concentrate completely on the road. Check the legal
provisions on the use of wireless devices in road traffic of the respective region. Always
observe these. If you use a wireless device during driving, rely on your good judgment
and remember the following:
1. Become acquainted with the wireless device and its functions such as the shortcut
dialing or dial repetition. These functions may prove to be useful if you would like to
make a call without taking your eye off the road.
2. Where possible, use hands-free equipment.
3. Let your dialogue partner know that you are behind the steering wheel. Where
necessary, discontinue the call in dense traffic or poor weather conditions. Rain,
sleet, snow, ice and even very dense traffic represent dangers.
4. Dial the required numbers carefully and estimate the traffic situation. Make your calls
when you have brought your car to a stop or before you leave. Plan your calls such
that they can be made when the car is parked. If you really must make a call during
the trip, only dial a part of the number, check the road and look in the rear view
mirror and then dial the rest of the number.
5. Do not surccumb to stressful and emotional telephone conversations which could
take your attention from the road. Let your dialogue partner know that you are in a
car and refrain from conversations which could take your attention away from the
road.
6. Call for help using your mobile device if necessary. Dial the emergency services
(911 in the USA and 112 in Europe) or other local emergency service numbers in the
event of fire, accidents or medical emergences. Remember that these calls are free
of charge on the wireless device! The call can be made independently of security
code or networks with or without the SIM card.
7. Help your fellow humans in emergency situations with your mobile device. If you
witness a serious accident, crime or other emergency, call the emergency service
(911 in the USA and 112 in Europe) or another local emergency service number
because you could be the one who needs help next time.
8. Call the breakdown service or a special mobile radio number for support if you
encounter problems on the road. If you pass a car with a breakdown, which does not
represent a serious impediment to traffic, pass traffic lights which do not function, a
traffic accident with slight damage and without injured people or a possibly stolen
car, please get in touch with the road police or another special mobile radio number
for support.
9. “The mobile communication industry requests you to give safety priority when using
your device/telephone.”
Operation
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
40/58
Subject to technical changes.
04/2015
6.4.1.3 Information for the use of wireless devices
Heed all warnings referring to the use of wireless devices.
6.4.1.4 Safety in aircraft
Switch off the wireless device when asked to do so by the ground staff and by employees
of the airline. If your device has a flight mode or a similar function, find out about its
correct use from the aircraft staff.
6.4.1.5 Safety in hospitals
Wireless devices emit radio frequencies and can cause disturbances to medical technical
electrical devices. Wireless devices should be switched off on request when you are in
hospitals, clinics or health establishments. This is intended to avoid any possible
interference with sensitive medical equipment.
6.4.1.6 Heart pacemakers
Manufacturers recommend that a minimum distance of 15 cm be observed between a
wireless handheld device and a pacemaker to avoid potential interference. This guideline
is in line with independent research results and recommendations of Wireless Technology
Research.
− Wearers of heart pacemakers
− Persons with heart pacemakers should ALWAYS keep at least 15 cm away from the
activated device.
− The device may not be worn by these persons in the breast pocket.
− The device should be held to the ear which is furthest away from the heart
pacemaker.
− If you have reason to assume that interference has arisen, you should SWITCH OFF
the device immediately.
6.4.1.7 Hearing aids
The wireless device may cause disturbances to hearing devices. Get in contact with the
manufacturer of your hearing device in the case of disturbances to ask about possible
solutions.
− The device may not be worn in the breast pocket of these persons.
− The device should be held to the ear which is furthest away from the heart
pacemaker.
− If you have reason to assume that interference has arisen, you should SWITCH OFF
the device immediately.
6.4.1.8 Other medical equipment
Ask your doctor or the manufacturer of the medical device to determine whether putting
the wireless product into operation impairs the medical device.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Operation
Subject to technical changes.
04/2015
41/58
6.4.2 Equipment of the laser devices
Devices from BARTEC/ZEBRA equipped with lasers comply with the Guidelines
21CFR1040.10 and 1040.11. (with the exception of the deviations set out in the Laser
Notice No. 50 dated 24 June 2007) and EN 60825-1:2007 and IEC 60825-1 (Ed. 2)
The classification of the laser device is stated on a plate attached to the device.
Laser devices of Class 2 work with a visible low volt light emitting diode. As for every
bright light source, for example the sun, you should not look directly into the light beam.
There is no information about the hazards of being briefly exposed to the laser light of a
laser scanner of Class 2.
The use of control elements, adjustments or the application of procedures which do not
comply with the instructions described here may lead to hazardous exposure to beams.
6.4.3 Restrictions to wireless devices
The use of wireless devices is possibly forbidden or restricted. This applies primarily on
board aircraft, in hospitals, in the vicinity of explosive substances or under other
hazardous conditions. If you are not sure which regulations apply to the use of the
device, ask permission before switching it on.
Country-specific roaming
This device has the International Roaming function (IEEE802.11d) which ensures that the
device is used on the channels prescribed for the respective country.
Ad-hoc operation
The ad-hoc operation is restricted to the channels 36–48 (5150–5250 MHz). The use of
this bandwidth is restricted to indoor areas; use outdoors is not permitted.
Operation
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
42/58
Subject to technical changes.
04/2015
FCC requirements to protect against high-frequency interference
This device has been tested and satisfies the limit values for a digital device of Class B
according to Part 15 of the FCC Guideline. These limit values were stipulated to
guarantee appropriate protection against disturbances if the device is used in residential
areas. The device generates and uses radio frequency energy and may emit this
energy. This can have a disturbing effect on other radio frequencies if the device is not
connected and used in accordance with the operating instructions. A guarantee that no
interference will arise for a certain installation cannot be given. If the device causes
interference to the radio or TV reception which can be recognised by switching the
device on and off, the interference should be eliminated by one or several of the
following measures:
− Re-alignment or moving of the receiving antenna
− Enlarging the distance between device and receiver
− Connecting the device to a different socket than the one to which the receiver is
connected
− Advice from the dealer or a radio/television technician
Radio transmission devices (Part 15)
This device satisfies the requirements of Part 15 of the FCC Guidelines. The operation of
the device is based on the following two conditions:
− The device may not cause any damaging interference
− The device must absorb all receiving interference including interference which may
lead to undesirable operation.
Requirements placed on the protection from high frequency interference - Canada
This digital device of Class B satisfies the Guidelines of the Canadian standard ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Radio transmission devices
This device corresponds to RSS 210 (Industry & Science Canada). The operation of the
device is based on the following two conditions:
− The device may not cause any damaging interference
− The device must absorb all receiving interference including interference which may
lead to undesirable operation.
Label symbol: “IC:” before the radio certification means that the technical data of Industry
Canada have been satisfied.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Operation
Subject to technical changes.
04/2015
43/58
Country approvals
Test symbols are attached to the device which show that the radio modules are approved
for use in the following countries: USA, Canada and Europe.
Detailed information on the test symbol for other countries is provided in the EC
declaration of conformity.
− N.B. 1: For 2.4-GHz-products: Europe covers Belgium, Bulgaria, Denmark, Germany,
Estonia, Finland, France, Greece, Great Britain, Ireland, Iceland, Italy, Latvia,
Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Austria, Poland,
Portugal, Romania, Sweden, Switzerland, Slovakia, Slovenia, Spain, Czech Republic,
Hungary and Cyprus.
European Economic Area
The operation of RLAN device (2.4 GHz) is subject to the following restrictions in the
European Economic Area (EEA):
− The 2.4 GHz devices may not excced a radiation of 100 mW EIRP and must be
within the frequency range of 2.400 and 2.4835 GHz.
− In France, devices used outdoors must be between 2.4 and 2.454 GHz.
− In Italy, a user licence is necessary for use outdoors.
The use of Bluetooth® Wireless Technology is subject to the following restrictions in the
European Economic Area (EEA):
− The 2.4-GHz devices may not exceed a radiation of 100 mW EIRP and must be
within the frequency range of 2.400 and 2.4835 GHz.
− In France, the devices used outdoors are restricted to 10mW EIRP.
− In Italy, a user licence is necessary for use outdoors.
Other countries:
− Mexico: Devices must be within the frequency range of 2.450 and 2.4835 GHz.
− Sri Lanka: Devices must be within the frequency range of 2.400 and 2.430 GHz.
Radio transmitters for RLAN devices
The operation of RLAN devices (5 GHz) is subject to the following restrictions in Canada:
− Frequency range restricted to 5.60 GHz to 5.65 GHz
− This device corresponds to the radio standard RSS 210 of the Industry & Science
Canada.
The following two conditions apply to operation:
− The device may not cause any damaging interference.
− The device must absorb all received interference, also interference which can lead to
undesired functions.
Labelling: the abbreviation “IC:” in front of the radio certification merely states that the
technical requirements of Industry Canada have been satisfied.
Operation
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
44/58
Subject to technical changes.
04/2015
6.5 Electromagnetic fields
6.5.1 International
The device satisfies internationally recognised standards for the exposure of humans to
electromagnetic fields of radio devices.
Reduction in high frequency energy – intended use
Only use device in compliance with the supplied instructions and the normal operating
position.
6.5.2 Portable devices
This device has been specially tested for operation in direct body proximity. Use
exclusively belt clips, holsters and similar accessories which have been tested and
approved by BARTEC to ensure compliance with the FCC regulations. Belt clips, holsters
and similar accessories of third manufacturers may not satisfy the FCC requirements for
the recommended maximum values for electromagnetic fields and should not therefore be
used.
The MC 75Aex-NI should only be worn on the body when switched off.
6.5.3 Handheld devices
To comply with the FCC guidelines for high frequency devices, the antenna of the
transmitter should be used in the direct vicinity of, or in an operation unit with, other
transmitters/antennas with the exception of those approved in this document.
SIM card
GSM telephone services require a SIM card (Subscriber Identification Module) or chip
card. A variety of service providers offer these cards. The card is used in the MC 75Aex-NI
and can contain the following information:
− Mobile telephone account details of the service provider.
− Information on the service settings and access to the services.
− Contact information which can be moved to the Contacts area on the MC 75A
ex
-NI.
− Any additional services which you have subscribed to.
Micro SD card
The Micro SD card slot provides a secondary, non-volatile memory. The slot is located at
the side of the MC 75Aex-NI (see figure). Further information is provided in the
documentation supplied with the card. Observe the manufacturer’s recommendations on
use.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Operation
Subject to technical changes.
04/2015
45/58
6.6 Optimise operating times/change energy settings
Factory settings of the MC 75Axex-NI for the WWAN and WLAN radio devices: ON.
6.6.1 Automatic shutdown in the case of lengthy standby periods
Symbols
In the start menu under:
> Settings symbol
> System symbol
> Power symbol
> Advanced tab
> Activate “Turn off device if not
used for” box and select a value
from the dropdown list.
> Confirm selection with “OK”.
6.6.2 Change display backlight (increases the operating time of the battery)
Symbols
In the start menu under:
> Settings symbol
> System symbol
> Backlight symbol
> Battery Power tab
> Activate “Disable backlight if
device is not used for” box and select
a value from the dropdown list.
> Brightness tab
> Select Disable backlight option. The
brightness of the backlight can be
regulated with a controller.
> Confirm selection with “OK”.
Operation
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
46/58
Subject to technical changes.
04/2015
6.6.3 Change keypad background lighting (increases the operating time of the battery)
Symbols
In the start menu under:
> Settings symbol
> System symbol
> Keylight symbol
> Battery Power tab
Activate “Disable keylight if device if
not used for” option and select a value
from the dropdown list.
> Advanced tab
Select “Disable keylight” option. The
brightness of the backlight can be
regulated with a controller or
switched off.
> Confirm selection with “OK”.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Operation
Subject to technical changes.
04/2015
47/58
6.6.4 Switch off radio connections
Products with Bluetooth® Wireless technology:
This device is an approved Bluetooth® product. Further information is available at
http://www.bluetooth.org/tpg/listings.cfm Manufacturer: ZEBRA
Symbols
Windows Mobile 6 devices have a simple
and central possibility in the form of the
Wireless Manager to deactivate and
configure all wireless functions of the
device.
In the start menu under:
> Settings symbol
> System symbol
> Connections symbol
> Wireless Manager symbol
Activate/deactivate wireless connection:
> activate respective button.
> All button
Wireless connections depend on the configuration.
6.7 Software versions
Existing software versions and operating systems in the MC 75Axex-NI:
The software is not relevant to the explosion protection of the device.
See the ZEBRA documentation for further information.
6.7.1 OEM
Symbols
In the start menu under:
> Settings symbol
> System symbol
> System Info symbol
> System tab
Operation
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
48/58
Subject to technical changes.
04/2015
6.7.2 Storage battery
Symbols
In the start menu under:
> Settings symbol
> System symbol
> About symbol
> Version tab
The last part of the build number contains
storage battery number.
6.7.3 Bluetooth
Symbols
In the start menu under:
> BT Information symbol
The “BTExplorer” application is only available if the “StoneStreet One Bluetooth Stack”
function is activated. Further information is provided in the ZEBRA “User Manual on
Integration” (MC75A User Guide).
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Operation
Subject to technical changes.
04/2015
49/58
6.7.4 “Fusion”software
Symbols
In the start menu under:
> Wireless Companion symbol
> Wireless Status symbol
> Point 7 “Versions”
6.7.5 “Phone” software
Is only possible with inserted SIM card.
Symbols
In the start menu under:
> Phone symbol
> Menu > Options
> Phone Info tab
Faults and
Troubleshooting
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
50/58
Subject to technical changes.
04/2015
7. Faults and Troubleshooting
DANGER
Risk of fatal injury in an explosive atmosphere!
Examine defective devices and any accessories only outside the potentially
explosive atmosphere.
Information on fault rectification is provided in the User Manual or the Integration
Manual from ZEBRA.
https://www.zebra.com
ZEBRA website for the MC 75Ax manuals for the non-Ex protected version
− SUPPORT & DOWNLOADS
− Support Portal
− Select your product to find manuals, software, and FAQ.
7.1 Resetting the Mobile Computer MC 75Ax
ex
-NI
7.1.1 Windows Mobile 6.x devices
It is recommended to restart the Mobile Computer MC 75Ax
ex
-NI if the applications do not
function in operation.
There are two restart functions: warm boot and cold start. If this does not function, the
MC 75Axex-NI can be reset to the factory settings using the Clean Boot.
7.1.2 Perform a warm boot
Data in flash memory or on a memory card are not lost.
The MC 75Axex-NI is restarted through a warm boot. The data records and entries
stored remain intact. If the MC 75Axex-NI does still not react following a warm boot,
perform a cold start.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Faults and
Troubleshooting
Subject to technical changes.
04/2015
51/58
The MC 75Axex-NI is restarted and all active programs shut down.
Works steps:
− Keep the ON/OFF button pressed for approx. 5 seconds.
− Release the ON/OFF once the warm boot commences.
7.1.3 Perform a cold start
Only perform a cold start if no improvement has been achieved with the warm boot.
The MC 75Axex-NI is restarted and all active programs are closed. The real-time clock
(RTC) is reset.
Work step:
− Keep the ON/OFF button and buttons 1 and 9 pressed simultaneously for
1 second.
The MC 75Ax
ex
-NI is initialised.
Further information is provided in the MC75A User Guide from ZEBRA.
Faults and
Troubleshooting
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
52/58
Subject to technical changes.
04/2015
7.1.4 Clean boot
ATTENTION
Incorrect handling may cause damage to property!
The Clean Boot must be conducted by an authorised systems administrator.
During the complete clean boot the MC 75Ax
ex
-NI must be provided with an
external voltage supply (e.g. cradle or charging cable) also.
A Clean Boot resets the MC 75Axex-NI to the factory settings.
Work steps:
1. Download the “Clean Boot Package” file from the ZEBRA SUPPORT website
(http://www.zebra.com/support) and install on the MC 75Axex-NI.
2. Copy the files in the download file according to the instructions to the Micro SD card
or the MC 75Axex-NI.
3. Press the ON/OFF button and the buttons 1 and 9 together.
4. Before the device restarts (before the Splashscreen appears), press the left scan
button.
5. Insert the MC 75Ax
ex
-NI into a cradle, which must be connected to an external
voltage supply. The MC 75Ax
ex
-NI starts to upload and reboot.
6. Recalibrate the touchscreen so that the MC 75Ax
ex
-NI is in the Todayscreen.
Further information is provided in the MC75A Integrator Guide from ZEBRA.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Service, Inspection, Repair
Subject to technical changes.
04/2015
53/58
8. Service, Inspection, Repair
Commissioning and service of Mobile Computers may be conducted exclusively by
trained and qualified staff! The staff is familiar with the installation, assembly,
commissioning and operation of the Mobile Computers, has been informed about the risks
and has the qualifications necessary for this work.
8.1 Service intervals
The mechanical state of the device should be regularly checked. The service intervals will
depend on the ambient conditions. We recommend that a service be conducted at least
once a year. Regular servicing is not necessary if the device is correctly operated in
accordance with the installation instructions and under appropriate consideration of the
ambient conditions.
DANGER
Prevent electrostatic charging in potentially explosive atmospheres.
Risk of fatal injury in an explosive atmosphere!
Do not dry wipe or clean devices.
8.2 Inspection
According to EN 60079-17 and EN 60079-19, the owner/operator of electrical plants in
potentially explosive atmospheres is obliged to have these plants checked by an
electrician to ensure that they are in a correct condition.
8.3 Service and repair work
In addition to Directive 99/92/EC, the standards EN 60079-17 and EN 60079-19 also
apply to the servicing and repair as well as the testing of accompanying operating
devices.
Work connected with assembly/dismantling, operation and servicing may only be
conducted by qualified staff. All statutory requirements and other binding guidelines on
occupational health and safety, accident prevention and environmental protection must be
observed.
Service, Inspection, Repair
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
54/58
Subject to technical changes.
04/2015
8.3.1 Information on sending in for repairs
The following information is required for the repair.
− Series number of the device (see manufacturer’s label)
− Model number or product name (see manufacturer’s label)
− Software type and version number (see Chapter 6.7)
Only ZEBRA may repair the devices!
Information on the Returns centres can be found on the
ZEBRA Homepage via
https://www.zebra.com
− SUPPORT & DOWNLOADS
− Support Portal
− Request a Repair
which contains the following information broken down by region:
Australia, China, Hong Kong, India, Indonesia, Japan, Korea South, Malaysia, New
Zealand, Philippines, Singapore, Taiwan and Thailand.
Central and South America
Argentina, Chile, Colombia, Ecuador, Mexico, Peru and Venezuela.
Europe, Middle East and Africa (EMEA)
Austria, Belgium, Croatia, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Ireland, Italy, Netherlands, Norway, Poland, Portugal, Romania, Russia, Slovak
Republic, South Africa, Spain, Sweden, Turkey and the United Kingdom.
United States & Canada
US and Canada.
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Disposal,
Dispatch and Packaging
Subject to technical changes.
04/2015
55/58
9. Disposal
The Mobile Computers contain metallic and plastic parts and electronic components.
The statutory requirements for electrical scrap must be observed for disposal, e.g.
disposal by an authorised disposal company.
10. Dispatch and Packaging Information
ATTENTION
Sensitive devices! Damage may be caused by incorrect packaging!
Use original packaging for transport.
Accessories
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
56/58
Subject to technical changes.
04/2015
11. Accessories
Accessories for use in the Ex area
Accessories for use in the non-Ex area
Mobile Computer MC 75Axex-NI and MC 75A6ex-HF-NI
Type B7-A27.-…………
Order Numbers
Subject to technical changes.
04/2015
57/58
12. Order Numbers
Mobile Computer MC 75A0ex-NI without WWAN option
Mobile Computer MC 75A6ex-NI with GSM HSDPA (WWAN) option
Mobile Computer MC 75A6ex-NI with EVDO (Verizon) option
Additional Information
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
58/58
Subject to technical changes.
06/2013
13. Additional Information
13.1 Links
http://www.bartec-group.com BARTEC website
https://www.zebra.com ZEBRA Homepage
The ZEBRA page for the MC75Ax User Manuals and software of the non-explosion
protected version
SUPPORT & DOWNLOADS
Support Portal
Select your product to find manuals, software, and FAQ
The ZEBRA product information page for the SCAN Engine, which is used in the
explosion protected version of the MC75A6exHF-NI.
PRODUCTS
OEM
OEM SCAN ENGINES
OEM ARRAY IMAGER
OEM ARRAY IMAGER SCAN ENGINES
SE4500 OEM ARRAY IMAGER SCAN ENGINE
or
PRODUCTS
OEM
OEM SCAN ENGINES
OEM LASER SCAN ENGINES
SE95x OEM LASER SCAN ENGINE
http://www.microsoft.com
Microsoft page for Active Sync or
Windows Mobile Device Center
Notice
Declaration of Conformity
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Declaration of Conformity
Certificate of Compliance
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
Certificate of Compliance
Certificate of Compliance
Mobile Computer MC 75Axex-NI and MC 75A6
ex
HF-NI
Type B7-A27.-…………
EN_B1-A275-7D0002/Revision A-04/2015-Automation Technology-305169
BARTEC GmbH
Germany
Max-Eyth-Straße 16
97980 Bad Mergentheim
Phone: +49 7931 597-0
Fax: +49 7931 597-119
info@bartec.de
www.bartec-group.com
BARTEC protects
people and
the environment
by the safety
of components,
systems
and plants.
Loading...