Barranca Diamond 6-inch TS6 Trim Saw User Manual

6-inch TS6 Trim Saw
Owner’s Manual and Operating Instructions
Revision 101 07.2009
Manual Part No. 167892
Caution: Read all safety and operating instructions before using this equipment. This manual MUST accompany the equipment at all times.
Barranca Diamond 22815 Frampton Avenue Torrance, CA 90501 Phone: (310) 523-5867 Toll Free: (800) 630-7682 Fax: (310) 257-3063 www.barrancadiamond.com
TS6
We at Barranca Diamond Products want to thank you for selecting the Barranca Diamond TS6 6-inch Trim Saw (part # 8300017). We are certain that you will be pleased with your purchase. Barranca Diamond takes pride in producing top quality and dependable products for both hobby and commercial lapidary users throughout the world.
Operated correctly, your TS6 6-inch Trim Saw should provide you with years of quality service. In order to help you, we have included this owner’s manual. This owner’s manual contains information neces­sary to operate and maintain your TS6 6-inch Trim Slab Saw safely and correctly. Please take the time to familiarize yourself with the TS6 6-Trim Saw by reading and understanding this manual.
If you should have questions concerning your TS6 6-Trim Saw, please feel free to call Barranca Dia­mond at (310) 523-5867 or toll free (800) 630-7682.
TABLE OF CONTENTS
SAFETY
Safety Precautions 3-6 California Proposition 65 Warning 6 Electrical Requirements & Grounding Instructions 7-8 Product Specications 9
OPERATION, ADJUSTMENT & MAINTENANCE
Assembly 10 Motor Mount 11 Power Switch 12 Cutting 13 Maintenance 14 V-Belt 15 Blade Assembly 16 Main Motor 17 Diamond Blade 18 Installation & Removal 19
ACCESSORIES
Accessories List 19
EXPLODED VIEW AND PART LIST
Exploded View 20 Part List 21 Service and Warranty 22
2
TS6 SAFETY
SAFETY PRECAUTIONS
Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to you or others. Failure to read and follow these instructions could also result in damage and/or reduced equipment life. In order to prevent injury, the following safety precautions should be followed at all times!
READ OWNERS MANUAL BEFORE USE
Before using this equipment, ensure that the person operating this machine has read and understands all of the instructions in the manual. Precaution is the best insurance against accidents. Read and understand all safety precautions, messages, warnings and hazard symbols. You are responsible for your own safety.
ALWAYS USE SAFETY GLASSES
Safety glasses should always be worn when working around power tools. In addition, a face, dust mask or respirator should be worn if a cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses and may not prevent eye injury - they are NOT safety glasses.
USE PROPER APPAREL
Do not wear loose clothing, gloves, neckties, rings, bracelets or other jewelry that may be caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair. Hand protection (plastic gloves) and a shop bib are recommended during sawing to prevent stains to clothing. Avoid prolonged exposure of skin to the sawing lubricant and wash skin immediately after contact. Do not touch the work material until the motor is off and the machine has come to a complete stop.
ALWAYS USE HEARING PROTECTION
To reduce the possibility of hearing loss, always use hearing protection when operating power equipment.
KEEP GUARDS IN PLACE
In order to prevent injury, never operate the saw without the guards in place!
REMOVE ADJUSTING KEYS AND WRENCHES
Form a habit of checking to see that keys and adjusting wrenches are removed from the power tool before it is turned on.
ELECTRICAL SHOCK
Never touch electrical wires or motor components while the motor is running. Exposed, frayed or worn electrical wiring and plugs can be sources of electrical shock that could cause severe injury or burns. Use the GFCI (Ground Fault Circuit Interrupter) Switch, included with the unit, attached to the main motor power cord plug and keep plugged into the power receptacle outlet source.
DISCONNECT TOOLS
Power tools should always be disconnected before servicing or when changing accessories, such as blades, bits, cutters and the like.
3
TS6 SAFETY
REDUCE THE RISK OF UNINTENTIONAL STARTS
Make sure the ON/OFF switch is in the OFF position before plugging in a power tool.
ROTATING OR MOVING PARTS
Keep hands, feet, hair, and clothing away from all moving parts to prevent injury. Never operate the motor with covers, shrouds or guards removed.
MAINTAIN TOOLS WITH CARE
Keep tools clean for the best and safest performance. Always follow maintenance instructions for lubricating and when changing accessories.
KEEP WORK AREA CLEAN
Cluttered work areas and benches invite accidents.
DO NOT USE IN DANGEROUS OR HAZARDOUS ENVIRONMENTS
Do not operate equipment in dangerous or hazardous environments. Do not use power tools in damp or wet locations nor expose them to rain. Always keep the work area well lighted. Always work in a well ventilated area.
KEEP CHILDREN AWAY
All visitors and children should be kept a safe distance from the work area. Keep power cords disconnected when tool is not in use.
MAKE THE WORKSHOP KID-PROOF
Make the workshops kid-proof by using padlocks, master switches and by disconnecting all power cords.
USE THE RIGHT TOOL Do not force a tool or an attachment to do a job that it was not designed to do.
SECURE WORK
Clamps or a vise should be used to hold work whenever practical. Keeping your hands free to operate a power tool is safer.
DO NOT FORCE THE TOOL
A power tool will do a better job and operate more safely at the feed rate for which it was designed.
USE THE RIGHT TOOL TO SERVICE THE SAW
Do not force a tool or an attachment when servicing or operating this power tool. Use the correct tools for service or adjustments.
DO NOT OVERREACH
Keep proper footing and balance at all times by not overreaching.
4
TS6 SAFETY
DO NOT OPERATE A TOOL WHEN TIRED
When tired, take a break and relax.
DIRECTION OF FEED
All blades, grinding wheels or polishing belts should always be installed such that rotation is in the direction of the arrow imprinted on the blade, wheel or belt.
ONLY OPERATE AT THE PROPER SPEED
Severe personal injury and damage to the motor or equipment can result if operated at speeds above maximum.
NEVER LEAVE A TOOL RUNNING UNATTENDED – TURN POWER OFF
Do not leave a tool until it comes to a complete stop. Always turn the tool off, and disconnect the power cord to its source, when leaving the work area or when work is finished. Do not leave extension cords attached to the power cord or power receptacle (wall outlet) when leaving the work area.
CHECK FOR DAMAGED OR WORN PARTS
Before using a power tool, check for damaged parts. A guard or any other part that is damaged should be carefully checked to determine if it would operate properly and perform its intended function. Always check moving parts for proper alignment or binding. Check for broken parts and mountings and all other conditions that may affect the operation of the power tool. A guard, or any damaged part, should be properly repaired or replaced.
USE RECOMMENDED ACCESSORIES AND PARTS
Consult the owner’s manual for recommended accessories and parts. Using improper parts and accessories may increase the risk of personal and/or bystander injury.
USE THE PROPER EXTENSION CORD If using an extension cord, make sure it is in good condition first. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage that will result in a loss of power and overheating. TABLE 1, shows the correct AWG (American Wire Gauge) size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
USE A GROUND FAULT CIRCUIT INTERRUPTER
Use of a Ground Fault Circuit Interrupter (GFCI) between the end of power cord and wall outlet is required at all times.
USE THE PROPER POWER SOURCE
This tool is only to be used with a 120 volt 60 HZ power source. Ensure power source is at least 15 amps and 110 to 120 volts. Low voltage current can adversely effect electric motor performance and overall life.
5
TS6 SAFETY
USE THE RECOMMENDED COOLING AND LUBRICATING FLUIDS
Never operate a tool dry that requires coolant or lubricant. This can lead to shortened tool life, tool damage and personal injury.
MAINTAIN TOOLS
Keep the diamond blade sharp, the sawing lubricant clean and reservoir filled to the correct level for the best and safest performance. Always follow the maintenance instructions for sharpening the blade, lubricating and servicing the saw.
CAUTION
Sawing, grinding and drilling generates dust. Excessive airborne particles may cause irritation to eyes, skin and respiratory tract. To avoid breathing impairment, always employ dust controls and protection suitable to the material being sawed, ground or drilled; (See OSHA 29 CFR Part 1910.1200). Diamond Blades improperly used are dangerous. Comply with American National Standards Institute Safety Code, B7.1 and Occupational Safety and Health Act covering Speed, Safety Guards, Flanges, Mounting Procedures, General Operating Rules, Handling, Storage and General Machine Conditions.
WARNING
CALIFORNIA PROPOSITION 65 MESSAGE
Some dust created by power sanding, sawing, grinding, drilling and other activities contain chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• Lead, from lead-based paints
• Crystalline silica, from bricks and cement and other masonry products and natural stone
• Arsenic and chromium, from chemically treated lumber
• Asbestos forming minerals
For further information, consult the following sources:
http://www.osha.gov/SLTC/silicacrystalline/index.html http://www.oehha.org/prop65/out_of_date/6022kLstA.html
Your risk from these exposures varies depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
6
Grounding Pin
Grounding Pin
(A)
(C)
(B)
(D)
ADAPTER
Grounding
Means
Metal Screw
Cover of Grounded
Outlet Box
Figure 1
TS6 SAFETY
ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS
In order to prevent potential electrical shock and injury, the following electrical safety precautions and symbols should be followed at all times!
In case of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
• Do not modify the plug provided – if it will not fit the outlet; have the proper outlet installed by a qualified electrician.
• Improper connections of the equipment-grounding conductor can result in a risk of electric shock. The equipment-grounding conductor is the wire that has a green outer surface, with or without yellow stripes. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
• Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.
• Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug.
• Repair or replace a damaged or worn cord immediately.
This tool is intended for use on a circuit that has an outlet that looks like the one shown in Sketch A of Figure 1. The tool has a grounding plug that looks like the plug illustrated in Figure 1. A temporary adapter, which looks like the adapter illustrated in sketches B and C, may be used to connect this plug to a 2-pole receptacle as shown in Sketch B, if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like, extending from the adapter, must be connected to a permanent ground such as a properly grounded outlet box.
NOTE: Use of a temporary adapter is not permitted in Canada.
Figure 1
To reduce the risk of electrocution, keep all connections dry and off the ground.
A Ground Fault Circuit Interrupter (GFCI) should be provided on the circuit(s) or outlet(s) to be used for this machine. Receptacles are available, having built-in GFCI protection, and may be used for this measure of safety.
When using an extension cord, the GFCI should be installed closest to the power source, followed by the extension cord, and lastly, the saw.
7
TS6 SAFETY
Supporting Surface
Power Tool
Drip Loop
Power
Cord
ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS (continued)
To avoid the possibility of the appliance plug or receptacle getting wet, position the saw to one side of a wallmounted receptacle. This will prevent water from dripping onto the receptacle or plug. A "drip loop," shown in FIGURE 2, should be arranged by the user to properly position the power cord relative to the power source.
The "drip loop" is that part of the cord below the level of the receptacle, or the connector, if an extension cord is used. This method of positioning the cord prevents the travel of water along the power cord and coming in contact with the receptacle. If the plug or receptacle gets wet, DO NOT unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the tool. Then unplug and examine for presence of water in the
Figure 2: Drip Loop
receptacle.
Use only extension cords that are intended for outdoor use. These extension cords are identified by a marking "Acceptable for use with outdoor appliances; store indoors while not in use." Use only extension cords having an electrical rating not less than the rating of the product. Do not use damaged extension cords. Examine extension cords before using and replace if damaged. Do not abuse extension cords and do not yank on any cord to disconnect. Keep cords away from heat and sharp edges. Always disconnect the extension cord from the receptacle before disconnecting the product form the extension cord.
To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch the plug with wet hands.
Use of under-size extension cords result in low voltage to the motor that can result in motor burnout and premature failure. Barranca Diamond warns that equipment returned to us showing signs of being run in a low voltage condition, through the use of undersized extension cords will be repaired or replaced totally at the customer's expense. There will be no warranty claim.
To choose the proper extension cord:
• Locate the length of extension cord needed in TABLE 1 below.
• Once the proper length is found, move down the column to obtain the correct AWG size required for that length of extension cord.
Extension Cord Minimum Gage for Length
Volts Total Length of Cord in Feet
120 v 25 ft. 50 ft. 100 ft. 150 ft.
AWG AWG AWG AWG
14 12 Not Recommended
Table 1
8
Loading...
+ 16 hidden pages