Bar Maid BLE-310 Installation Manual

INSTRUCTION MANUAL

3HP COMMERCIAL BLENDER BLE-310

BLENDER SAFETY

DANGER Electricity GENERAL Caution

DANGER Risk of Electrical Schock DANGER Keep Hands Clear

WARNING WARNING

Electrical Shock Hazard Moving Parts!

Plug into a grounded outlet.

Do not remove ground.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can
result in death, fire or electrical shock.

Always cover the lid on the container when
blending.

Do not put hands. spoons or other utensils in
container when blending.

Failure to fol low these instructions can result
in broken bones, cuts or other injuries.

FAILURE TO ADHERE TO THESE WARNINGS CAN RESULT IN FIRE,

SERIOUS INJURY, ELECTRICAL SHOCK AND/OR DEATH

For Warranty Assistance:

1-866-531-6243

For Parts or Technical Assistance:

[phone]

1-800-526-5278

1.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic
safety precautions should always be
followed, including the following:

1. Read all the instructions before using
the blender.

2. Plug into a grounded outlet.

3. Do not remove ground.

4. Do not use an adapter.

5. Do not use an extension cord.

6. To protect against risk of electrical shock,
do not put the blender in water or other
liquid.

7. Close supervision is necessary when any
appliance is used near Children.

8. Unplug from outlet when not in use, before
putting on or taking off parts, and before
cleaning.

9. Avoid contact with moving parts, especially
blades.

10. Do not operate any appliance with a
damaged cord or plug or after the
appliance malfunctions, or is dropped or
damaged in any manner. Return
appliance to the nearest authorized
service facility for examination/repair
/electrical or mechanical adjustment, or
contact your distributor.

11. Caution: Keep hands and utensils out of
container while blending to reduce the risk
of severe injury to persons or damage to
the blender. If scraping, folding, etc. Is
necessary, turn off and unplug the
blender, and use a rubber spatula only.

12. Warning; Blades are sharp. Handle
carefully.

13. To reduce personal injury, never
place cutting blades on base without jar
properly attached.

14. If so equipped, screw on locking ring
firmly. Injury can result if moving blades
accidentally become exposed.

15. Always operate blender with lid in place.

16. WARNIING: When blending hot liquids,
place a hand towel over the cover. Do not
fill blender container beyond 2/3 full.
Always begin processing at the lowest
speed setting. Keep hands, arms and
face away from the feeder cup opening to
prevent possible burns.

17. Do not use outdoors.

18. Do not let cord hang over edge of table
or counter, or touch hot surfaces.

19. Do not leave blender unattended while it
is operating.

20. The use of attachments not approved by
BarMaid may cause injuries.

21. The capacity may be substantially less
than normal with thick mixtures.
Do not overfill.

22. Inspect the container assembly daily. Do
not use a broken, chipped or cracked
container. Check cutter for wear, nicks or
broken blade for wear.

23. This blender is intended for short periods
of operation, with an average rated
operating time of approximately 3
minutes.

24. This appliance is not intended for use by
persons (Including Children) with reduced
physical, sensory or mental capabilities or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the
appliance by a person responsible for
their safety. Children should be
supervised to ensure they do not play with
the appliance.

2.

BLENDER OPERATION

To operate the blender, proceed as follows:

1. Before the initial use, wash container assembly and lid thoroughly.
(Refer to “Cleaning Instructions") DO NOT PUT THE CONTAINER ASSEMBLY &

BLENDER BASE ASSEMBLY IN THE DISHWASHER.

2. Place the blender on a dry, clean, level surface, and press OFF.

3. Place the container onto the motor base. Make sure it rests securely on the base.

4. Plug the blender into an electric outlet.

S. Place the ingredients into the container.

4. Place the lid and feeder cap tightly on the container.

7. Select the desired speed and time by rotating dials.

8. Press ON.

NOTES

Pulse Button - Pressing the pulse button will cause the motor to run for as long as the

button is depressed. Removing your finger from the button will cause the motor to stop
running and the blades to stop turning.

Infinity Button-Pressing this button will cause the motor to run at alternating RPM until
the timer expires to thoroughly blend most mixtures.

BLENDING TIPS

1. Processing hot liquids

● Always cover the lid and feeder cap before blending hot liquids or mixtures.

● Use the feeder cap to add liquids to the container while the unit is running.

● Never stand with your face directly over the container when you are putting
ingredient through the feeder cap.

2. Blending icy mixtures

● Steps for blending ice:

1. Pour in liquid, and then add ice.

2. Place the lid and feeder cap tightly on container.

3. Set to desired speed and time.

4. Use the feeder cap to add liquids or ingredients to the container while the unit
is running.

3.

CLEANING INSTRUCTIONS

The BLE-310 blender container parts are corrosion resistant, sanitary
and easily cleaned. Do not put the container assembly or blender base
assembly in the dishwasher.

1. Before first use and after every use, separate container from the base.

2. To clean the container: Use a washing solution of tepid water (less than 115°F/46°C)
and a non-sudsing detergent.

3. Scrub and flush out the container interior lid and feeder cap to remove food residue.
Empty container.

4. Fill container 1/4 full with fresh washing solution and place it on the base.

5. Replace the lid and feeder cap on the container and run the blender on high speed
for 2 minutes.

6. Repeat step 4 using clean rinse water (95°F/35°C).

7. Wipe down the outside of container, feeder cap, and lid with a soft cloth or sponge,
dampened with fresh washing solution.

8. Wipe the exterior of the base with a damp cloth or sponge. The base contains
electrical components: do not immerse. use a high-pressure washer, or use a
dishwasher to clean the base.

BLENDER CARE

For best results:

1. Periodically check all parts before reassembly. Use of damaged or non-recommended
parts could result in severe personal injury and/or damage to the blender.

2. Blades:
If the processing blades are stuck or difficult to turn. DO NOT USE BLENDER.
Remove container from the base. Check by carefully turning the blades in a counter­ clockwise direction, where the opposite edges are sharp. Blades should turn freely.
If not. call for service or replace container.

3. Container:
If the EASTMAN TRITAN container is cracked, DO NOT USE BLENDER, further use
could result in the container breakage during use.

4. Blender Base:
Never immerse the blender base in water. To clean, unplug base and use a damp
cloth.

5. Motor:
The motor is permanently lubricated and does not require any additional lubrication.

4.

TROUBLESHOOTING

Problem

1. Blender fails to start

2. Stopped

3. Ingredients do not mix properly

Solution

1. Place container properly on the base.

2. Check to ensure controls are clean
and moving freely.

3. Double-check to ensure power cord is
securely plugged into the electric outlet.

4. Check to see if the circuit breaker has
tripped or if the fuse for the electric
outlet has blown.

5. Check the onboard reset switch located
at the rear of the blender base.

1. Check the onboard reset switch located
at the rear of the blender base.

2. Unplug blender and wait 5 minutes.

3. Plug the blender back in and resume
operation.

1. Container is too full.

2. Cutter unit blades are not sharp
enough or are damaged.

3. Solid pieces are bigger than 1"
(25mm) cubes.

4. Check the speed to create a fluid
blend.

5. Check to see if enough liquid has
been added to the ingredients. Mixture
should be fluid and free-running at all
times.

5.

MAINTENANCE

Inspect the blender and its various parts and replace as follows:

1. Unplug the blender and remove the
container from the base.

Daily

Weekly

2. Inspect the container blades for wear,
nicks, and broken or loose blades.
Replace if necessary.

1. Unplug the blender.

2. Inspect the power cord insulation and
power plug for cracks. Refer to
"Technical Service" for repair or
replacement.

1. Review the condition of the container

Quarterly

assembly and Mushroom Clutch Set at
least every 90 days.

2. Replace if necessary.

Replacement Part

For replacement parts, call toll free: # 1-800-526-5278

6.

BAR MAID CORPORATION

2950 NW 22nd Terrace,

Pompano Beach, FL 33069

www.barmaidwashers.com