Page 1
4 Setting temporary IP address
using ARP command
This pro cedure will work onl y in a local n etwork.
After th is proced ure the temp orary IP w ill be acti ve
only until restar t/rebo ot. After a res tart the p rocedur e
has to be repeated.
STEP 1
Either u se a networ k cable to li nk the Exstr eamer an d
the PC directly, or connect the Exstreamer to the PC
via your n etwork sw itch and powe r the devic e. Make
sure that you have a valid s tatic IP add ress conf igured on
your PC (e.g. 192.168.0.2)
STEP 2
Window s : For a comma nd window. cli ck on «Star t», click
on «Run..», in the «O pen» fie ld type cm d , click on «OK».
OSX / Linu x : Open a term inal window.
STEP 3
Please proceed to step 4 if you linked the PC dire ctly to
the devi ce in step 1. To ensure tha t you use a free I P
addres s (not already used by another devi ce in the net work)
please use the Ping command. To verify availability in
this example we assu me the PC to have th e IP addres s
«192.168.0.2» and want to ch eck if «192.168.0.6» is fre e.
Typ e p in g 1 92.168.0.6 and hit the «Enter» key. You
should get no reply w hich give s you reaso nable ass ertion
that the «p inged» IP i s availabl e.
STEP 4
Look for th e Exstrea mer’s MAC addre ss printe d on a
label o n the bottom of t he device (12 hex dig its, separated
by a hyphe n every 2 digits). Type into the wi ndows
command window
arp -s 192.168.0.6 00-08-E1-00-B1-77
or on a OSX or L inux syste m type into th e termina l
arp -s 1 92.168.0.6 0 0:08:E1:00:B 1:77
and hit th e «Enter» key (replace the dig its according to your
devices MAC address). You must have administrative rights
to be able to d o so (sudo on OSX / L inux).
STEP 5
Now we have to ma ke the Exstr eamer lis ten to the IP
addres s «192.168.0.6» using the Telnet comman d. To do so
type into the comma nd window telnet 192.168.0.6 1
and hit th e «Enter» key (the n umber «on e» must be there
for this c ommand to wor k correc tly !!!). The Exstreame r will
immediately refuse the connection on port 1, but will be
available for brows er acces s as long as th e device stays
powered.
STEP 6
To check if the E xstreamer is respo nding you c an use
the ping c ommand ag ain. To do so type p in g 1 92.168 .0.6
and hit th e «Enter» key. If you do ge t a reply the IP a ddress
192.168.0.6 can be u sed to acce ss the Ex stre ame r using a
web brows er. Please go back to section «2 Network configura-
tion by web b rowser» to confi gure a static IP address . If you do
get «req uest time d out» then ple ase repea t step 5 caref ully (you
most like ly misty ped the tel net comma nd) or repe at the entire
procedure. If the AR P method does not work for you, refer to
the user manual for further methods.
5 Troubleshooting
• If the displ ay (C) stays dark ch eck the p ower
cabling (installation step 3).
• Check if the green L INK LED (I ) is lit, i f it is not then
check your network cabling (network port G).
• If you have dou bts abou t the cur rent device sett ings
you can revert the de vice to its factory defaults by
press ing the Reset but ton (A) un til the re d status L ED (C)
blinks r apidly (takes about 10 seconds). The d evice wil l
reboot o nce the but ton is released..
For information about our products, manuals, technical
documentation, latest firmware, support and access to
the user forum please visit www.barix.com.
EXSTREAMER
110
Quick Install Guide
Version 3.1
Multiformat IP Audio Decoder
Package contents
a Exstreamer 110
b Power supply
c RCA Stereo cable
d IR remote control
e Batteries (2 x AAA)
Cable Set AUDIO (not included)
f Earphone
g RCA Stereo cable
h Network cable
i Serial cable
Firmware
This device comes preloaded with standard firmware.
Alternative firmware can be downloaded from www.barix.com.
Barix AG, Seefeldstrasse 303, CH-8008 Zürich
P +41 43 433 22 11
info@barix.com, www.barix.com
2007_4161_Exstreamer_110_Quick_Install_Guide_31.indd 2-3 03/03/15 15:32
Support
For support please contact your local dealer or visit www.barix.com.
© Barix AG 3/2015, all r ights reser ved. All informati on is subjec t to change with out notice. A ll mentione d trademar ks belong
to their res pective own ers and are us ed for refere nce only. Barix , Exstreame r and SonicI P are tradema rks of Barix AG, S witzerl and,
and are reg istered in ce rtain cou ntries.
Page 2
Front view
E
BA
C
A Rese t button
A brief press of the bu tton will re set the device.
Holding the reset b utton pres sed in for approximate ly
10 seconds will reset the device a nd restore th e factory
defaul t setting s when the bu tton is rel eased.
B E XT.
USB inter face solely for fl ash memor y sticks
(not supplied)
C LCD
Status display
D Headphone out
Stand ard stereo mini jack (3.5 m m)
E IR sensor
USB inter face solely for fl ash memor y sticks
(not supplied)
F Line ou t
Stereo RCA line outputs
G RS-232 serial port (DSub 9 pin male)
Pin Description
1 Relay common
2 Re ceive Dat a [RxD]
3 Transm it Data [ TxD]
4 V+ 12V*, 100mA max
5 Gro und [GND]
6 Not connected
7 Re ady to Send [RTS]
8 Cle ar to Sen d [CTS]
9 Relay Normally Open
* Pin 4 wi ll provide 2.6V le ss than the supplied voltage on Vin+
(H) but not m ore than 12V.
D
Rear view
1
5
6
9
F G H I
H LAN po rt 10/100 (RJ45)
Standard RJ45 Eth ernet socket
Pin Description
1 Tx +
2 Tx -
3 Rx +
4 Not supported*
5 Not supported*
6 Rx -
7 Not supported*
8 Not supported*
* do not c onnect PoE p ower at this pi n
I Power (6 Watt ma x.)
Pin Description
1 Vin - (ri ng)
2 Vin+ (ce nter pin)
9..30 VDC
12..24 VAC
J LAN s tatu s LEDs
Green LED for Link, yell ow LED for Activit y
1 Installation
STEP 1
Plug a standard (straight) network cable (h, not included)
into the network por t (H) of the E xstreame r and the
J
18
other en d into your hub o r switch. You can al so use
a crosso ver networ k cable (not i ncluded) for a direc t
connection to your PC.
STEP 2
i) Plug standard headphones or the earphone (f, not
included) into the he adphone output (D) and li sten.
ii) Plug the RCA cable (c) into the L INE OUT out puts
(F) and connect the cable to in puts of your m ixing
console or monitoring device and listen.
2 Network configuration
by web browser
Most Barix applictaions require no configuration but use
DHCP to configu re network setti ngs dyna micall y.
If you nee d to use static ( fixed) network set tings foll ow
steps 1 to 3, oth erwise c ontinue f rom step 4.
STEP 1
Open your web browse r.
STEP 2
Enter the I P address th at was anno unced by the E xstream er
and press Enter. Examp le: 192.168.0.12 Clic k on the
Configuration button, then on Advances Settings/Network.
STEP 3
Conne ct the Power su pply (b) to the d evice (soc ket I)
and then to an appropriate elec trical ou tlet.
STEP 4
i) The E xstreame r will now ac quire an IP ad dress and
anno unce it over the sp eaker ou tput (if no DHCP
server is availa ble this ca n take up to 5 minu tes).
ii) If you did not c onnect an y audio outp uts in step 2,
either see the next page for the ARP command
proce dure, or use the “Barix Discover y Tool” Java
application (download the latest version from www.
barix.c om) on your co mputer (Windows, Ma c or
Linu x) and cl ick the “Get” but ton to fi n d out wh ich
IP addre ss the devi ce has obtained (see pi cture at the
bottom of the page). Make su re that the Eth ernet
addres s (MAC) matches your devi ce (see lab el on the
bottom of the device).
STEP 3
In order to m ake the appl ication wo rk the follo wing para meters
must be set (check with your netwo rk admini strator):
• static IP add ress (the default «0.0.0.0» sets automati c
discove ry: Bo otP, DHC P) and net mask
If your devices are c onnected via router s also:
• Gateway IP addr ess
Hit the «A pply» but ton to save all ch anges. The device w ill
reboot w ith the conf igured IP a ddress.
STEP 4
Now that yo u know the IP ad dress proceed to the nex t
sectio n “Network conf iguratio n by web b rowser”.
If you were n ot able to obta in the device’s current
IP addre ss with the p revious ste ps see sec tion
”Troubleshooting”.
To complete the application setup, download the firmware
documentation from www.barix.com. Download the product
manual for additional information about the hardware instal-
lation, te chnica l and mecha nical de tails as wel l as instru ctions
on updat ing or chan ging the lo aded appl ication fir mware.
3 Infared remote control
STEP 1
Inser t the batte ries (e) into the remote contr ol (d),
observing the polarity requirements.
STEP 2
Read the f irmware u ser manua l for inform ation abo ut
configuration of the IR sensor and the supported
functions of the IR remote control.
2007_4161_Exstreamer_110_Quick_Install_Guide_31.indd 4-5 03/03/15 15:33
Loading...