Barcus Berry C5200 User Manual
Specifications for the 3000 Piezo Buffer Preamp with EQ
Input (EQ Flat)
Input Interface = RCA unbalanced
Input Impedance = 2.2 Meg Ohms
Maximum Input Level = 2.0 vrms
Output (EQ Flat, Volume Max)
Output Interface = 1/4" unbalanced
Output Impedance = 2K Ohms
THD = .008% @ 1kHz
Noise = -92dBu
S/N = 100dBu
Bass = +/- 12dB @ 50Hz
Treble = +/- 12dB @ 10kHz
Frequency Response = 5Hz - 30kHz (+/- 1dB)
Power Supply
Power Source = 9 Volts @ 380 Microamps
Battery Life = Approximately 1,000 hours
Made In The U.S.A.
This Barcus-Berry product is designed to satisfy
the most rigorous demands of the professionalmusician and the precision manufacturing
techniques employed provide assurance of
long-continued, trouble-free service. For
outstanding performance and dependability, you
can always rely upon BARCUS-BERRY— the
world’s leading name in musical instrument
transducers, pickups and microphones.
Limited Warranty
This Barcus-Berry product is warranted for a period
of one (1) year from the date of purchase against
defects in workmanship and parts.
Woodwind & Brass System
InstallatIon InstructIons
for
W o o d W I n d & B r a s s t r a n s d u c E r s Y s t E M
model no.
ö
C5200
õ
P.O. Box 63366
N. Charleston, SC 29419-3366
www.barcusberry.com
6525
Installation
Congratulations on your purchase of the C5200 Barcus-Berry Electret Mic System
for Woodwind and Brass Instruments
This model has been specifically engineered for use with saxophone and clarinet, but is not limited to these instruments. It is ideal
for both ensemble and solo applications. The microphone itself utilizes an exclusive Barcus-Berry design which offers superior
audio performance, and the adhesive mounting makes attachment to or removal from quick and easy. The system has wide-band
frequency response, excellent dynamic range, and provides clean, faithful reproduction of the acoustic sound.
Remove the protective paper covering from the pickup. The
following will provide you with recommended starting points for
positioning of the microphone. Critical placement on any given
instrument may require a slight variation as to mounting loca-
tion, but the instructions given here can be expected to pro-
duce excellent results for quick attachment in most instances.
Harmonica - The microphone can be quickly attached to and
removed from the comb of any harmonica. The configuration,
size, and weight of the sensor make its presence
unobtrusive both in use and appearance.
Important
Before you begin, please check within the box to insure that it contains the
following items:
(A) • One (1) Barcus-Berry Barcus-Berry dedicated electret microphone pickup
for woodwind and brass instruments
• Extra adhesive strips for microphone.
(B) • One (1) Barcus-Berry 3000 Piezo Buffer Preamp with EQ.
• One set of rubber feet (four each).
•Attachable belt clip with “dual lock” fastening strips.
• Installation Instructions for Model C5200.
If any of these items are found to be damaged or missing, immediately
contact the Barcus-Berry dealer from whom the unit was purchased.
(B)
(A)
Note: When removing any advhesive from an instrument, care
must be taken so as not to damage the finish of the instrument.
Alto/Tenor Sax - Position the microphone on the backside of
the bell (between the bell and the keys) just below the flair of
the bell.
Soprano Sax - Position the microphone on the backside of the
instrument, one inch below the thumbrest and slightly to the
right of the center.
Clarinet - Position the microphone on the backside of the lower
section, four inches below the thumbrest.
Operation
Once the microphone has been attached, it can be plugged
into the 3000 Piezo Buffer Preamp with EQ with the furnished
cable. Any connecting cord with 1/4” phone plugs can be used
to interface the system with standard high impedance inputs
of 10K ohms or more. The 3000 utilizes a 9V battery and has
volume, treble and bass controls. Access for replacement
of the battery, when necessary, is obtained by removing the
screws which retain the wrap around the chassis cover.
Loading...