CompactLink
Installation manual
R9853320
R9853340
R9853323
R5976867/02
12/04/2007
Barco nv Events
aan 5, B-8520 Kuurne
Noordl
Phone: +32 56.36.89.70
Fax: +32 56.36.88.24
sales.events@barco.com
E-mail:
Visit us at the web: www.barco.com
PrintedinBelgium
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall n ot otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Guarantee and Compensation
Barco provides aguaranteerelatingtoperfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for damage incurred during transport, as wellas for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to c ompensation for direct or
indirectdamage, and also damage attributed to the operationof software as well asto other services provided by Barco, being a component
ofthe system or independent service, will be deemed invalid p rovided the damage is not proven to beattributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,
in particular if the systems are commissioned operated incorrectly or if, after the transfe
agreed upon in the contract, all guarantee claims of the purchaser will be rend ered invalid. Not included in the guarantee coverage are
system failures which a re attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as
well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as wellas the servicing and maintenance regulations specified in the this manual must be complied with by
the customer.
r of risks, the goods are subject to influences not
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments o
the products or their manufactures.
r examples and are not to be understood as advertising for
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied w arranties or merchantability an d fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this p ublication.
1. INTRODUCTION
Purpose of the CompactLink
The CompactLink allows to have a bigger distance between the digitizer and the LEDwall or between to parts of a LEDwall.
1.1 Overview of the different kits
The order numbers of the kits
1. Introduction
Order number
R9853320
R9853340
R9853323
Description
CompactLink 50 (complete kit)
CompactLink cable interface kit
CompactLink 50 without cables
1.2 CompactLink 50
Overview R9853320
Article
number
R9853323
Z3499464
Z3499461
Z3499463
Z3499462
R849380 Water resistant housing 2 image 1-6
R724879
Description
CompactLink 50
CableDVI-DVI600mm
Cable DVI - MDR 26 Compact 600 mm
Cable DVI - MDR 26 Waterproof input 600 mm
Cable MDR 26 waterproof output - DVI 600mm
Cable sealing
Quantity Image reference
1 image 1-1
2 image 1-5
2 image 1-3
1 image 1-2
1 image 1-4
8 image 1-7
V395180 Impregnated silicone tube 1
Wire tire 8
Image 1-1
CompactLink cable 50
R5976867 COMPACTLINK 12/04/2007 1
Image 1-2
Cable DVI - MDR Waterproof input 600mm
Image 1-3
Cable DVI - MDR Non-Waterproof input 600mm
1. Introduction
Image 1-6
Waterproof housing
Image 1-4
Cable DVI - MDR Waterproof output 600mm
Image 1-7
Cable sealing part
Image 1-5
Cable DVI - DVI 600mm
1.3 Cable interface kit R9853340
Overview
Article
number
Description
uantity
Q
mage reference
I
Z3499464
Z3499461
Z3499463
99462
Z34
CableDVI-DVI600mm
Cable DVI - MDR 26 Non-Waterproof 600 mm
ble DVI - MDR 26 Waterproof input 600 mm
Ca
Cable MDR 26 waterproof output - DVI 600mm
2 image 1-5
2
1 image 1-2
1 ima
ge 1-4
2 R5976867 COMPACTLINK 12/04/2007
2. CONFIGURATION DIAGRAMS
2.1 Overview
CAUTION: The first tile after the CompactLink must be correctly connected to the power and functionally OK,
otherwise the wall will not sta rt up !
Between Digitizer and outdoor LEDwall
Transmitter
B
C
A
2. Configuration diagrams
D
F
Image 2-1
Digitizer - CompactLink - Outdoor ledwall
A Digitizer
B DVI - DVI 600mm cable
C Waterproof housing
D CompactLink 50
E DVI – MDR 26 waterproof input cable
F Outdoor LEDwall (DLite, SLite, OLite)
Between Digitizer and indoor LEDwall
B
A
Image 2-2
Digitizer - CompactLink - Indoor ledwall
A Digitizer
B DVI - DVI 600mm cable
C Waterproof housing
D CompactLink 50
E DVI – DVI cable 600mm
F Indoor LEDwall (ILite)
C
E
Receiver
Transmitter
D
C
F
C
E
Receiver
R5976867 COMPACTLINK 12/04/2007
3
2. Configuration diagrams
Between outdoor LEDwall and an outdoor LEDwall
B
C
Transmitter
D
F
A
Image 2-3
Outdoor ledwall - CompactLink - Outdoor ledwall
A Outdoor LEDwall (DLite, SLite, OLite)
B MDR 26- DVI 600mm output cable
C Waterproof housing
D CompactLink 50
E DVI – MDR 26 waterproof input cable
F Outdoor LEDwall (DLite, SLite, OLite)
Receiver
Between indoor LEDwall and an indoor LEDwall
Transmitter
B
C
A
Receiver
C
E
D
F
C
E
Image 2-4
Digitizer - CompactLink - Indoor ledwall
A Indoor LEDwall (ILite)
B DVI - DVI 600mm cable
C Waterproof housing
D CompactLink 50
E DVI – DVI cable 600mm
F Indoor LEDwall (ILite)
When a MiPIX wall is used in one of the configurations, use the DVI - MDR 26 non waterproof cable to connect
to the CompactLink.
4 R5976867 COMPACTLINK 12/04/2007
3. Installation
3. INSTALLATION
3.1 Mounting the waterproof housing
How to mount ?
1. Put one part of the cable sealing around the cable (1).
Use the 8 mm sealing parts for the fiber cable.
Use the 9 mm sealing parts for the other cables.
An 8 or a 9 is indicated inside the sealing.
2. Put some impregnated silicone on the contact borders of both pieces.
3. Place a second cable sealing part on the first one (2). (image 3-1)
4. Closethesealingwith2wireties. (image3-2)
Tip: Try to place the junction of the wire tie somewhere at the side. It makes the closing of the housing easier.
5. Repeat those actions for the other cable end.
6. Make the connection. Plug in and secure with the hand screws. (image 3-3)
7. Insert both sides of the connection into the waterproof housing. Be aware that the grooves in the sealing matches the opening
in the waterproof housing. (image 3-4)
8. Spread so me impregnated silicone on the contact borders of the housing.
9. Place the second part of the housing on the first part and pull until the housing is completely c
10.Secure by turning the hand screws (on both s ides of the housing) a quarter turn anti clockwise. (image 3-5, image 3-6)
Tip: Use the velcro strip to make a loop so that the housing can be attached somewhere.
losed.
Image 3-1
Mount cable sealing
(1)
(2)
R5976867 COMPACTLINK 12/04/2007 5
3. Installation
Image 3-2
Close sealing
Image 3-3
Make connection
6 R5976867 COMPACTLINK 12/04/2007
Image 3-4
Insert connection into housing
3. Installation
Image 3-5
Close top cover
R5976867 COMPACTLINK 12/04/2007 7
3. Installation
Image 3-6
Housing closed
8 R5976867 COMPACTLINK 12/04/2007
Loading...