Barco R 9849999 User Manual
R 9849999
INSTALLATION MANUAL
Ceiling Mount for CLM series projector
Date 26/11/07 Rev: 00 Art. No.: R 59770182
Due to constant research, the information in this manual is subject to change without notice.
Visit Barco at the web: http://www.barco.com
Produced by BARCO NV,Nov. 2007.
All rights reserved.
Trademarks are the rights of their respective owners.
BARCO n.v.
Noordlaan 5
B-8520 Kuurne
Belgium
Tel : +32/56/368211
Fax : +32/56/351651
E-mail : sales.bps@barco.com
Printed in Belgium
Safety guidelines
WHO
WARNING
CAUTION
PRODUCT CARE
This installation manual must be performed by authorized technical personnel
The ceiling should be capable of supporting a weight of at least 5 times the total
weight of the Ceiling Mount and Projector (i.e. at least 160 kg or 353LB). If it
cannot, the ceiling must be reinforced. Improper installation may result in serious
Consult a professional structural engineer prior to suspending the Ceiling Mount
from a structure not intended for that use.
Always ensure the working load limit of the structure supporting the Ceiling Mount.
Installing the Ceiling Mount should be performed only after you are thoroughly
familiar with all of the following safety checks and installation instructions.
To do otherwise increases the risk of hazards and injury to the user.
This support is designed for intended use only with Barco CLM series projectors. It
supports maximum 33 kg or 73LB. Use with any other appliance/projector may
result in instability causing possible injury.
Do not modify and/or replicate any component. Barco n.v. uses specific materials
and manufacturing processes in order to achieve part strength. Consult Barco nv
for assistance with custom applications.
Always follow Barco installation instructions. Contact Barco n.v. if you should have
any question regarding the safety of an application.
Ceiling Mount components should be kept dry, clean, lubricated (if required),
coated properly, and otherwise maintained in a manner consistent with part
design. Barco products must be used in a manner consistent with their design and
inspected on a routine basis for security, wear, deformation, corrosion and any
other circumstances that may affect the load handling capability of the part.
Barco n.v. recommends inspections at least once a year for all installations and
increasing in frequency for more critical installations. If the part is found to have
damage, which may cause a decrease in load capability, the part must be removed
Under no circumstances are Barco parts repariable by anyone other than Barco
only.
personal injury.
from service immediately.
n.v.
Description and Contents of the kit
Purpose of the Kit
The kit is designed for the CLM CM R10 series projectors and allows the
projector to be mounted to the ceiling.
Contents of the Kit
Following items are included:
• Kit R9849999: Ceiling mount
• Installation manual : R59770182
• Mounting bracket and Screws: R835785 Qty 3 Nos and R 826743 qty 1
No, - --
• Safety Chain set : B361213 Qty 1 Nos , A577535 qty 1 Nos, A566050 qty
1 nos and B363509 qty 2 nos
• Cable cover assy
Illustration of the ceiling mount
R826743
R835786
R83578
Remark:
V367
The ceiling mount can also be mounted using one of the 2 available bars (height
adjustment) and cable cover assy.
R9841260: short bar R822922 and cable cover assy .
min length = 445mm(17.52 inch)
max length = 810 mm(31.89 inch)
R9841261: long bar R822923 cable cover kit R984 .
min length = 845mm(33.27 inch)
max length = 1210 mm(47.64 inch)
I
llustration of the Cable Cover Assy:
R826748
R826761
G229790 &
5126
R826749
R826745
R347968 (7X)
Z348001( 4X)
R347972 ( 4 X)
Note: The assembly is used only when ceiling mount is mounted along with
IQ bar for hiding and guiding the cables.
Mounting the Assembly
Necessary Tools
1. Torx screw driver for M3 screw
2. Hexagonal driver (n° 6)
3. Ring spanner 12-13mm
4. Side spanner 12-13mm
5. Cross head screw driver for M8 screw
Centering the ceiling mount
Mark the position on the ceiling hole. Since the center of the lens does not
coincide with the center of the projector, the center of the lens has been marked
on the ceiling mount.
Remark
The horizontal shift of the ceiling mount allows to re-enter the projector later on,
However, centering decently the base plate insures a good horizontal shift
margin afterwards
.
Loading...