Barco R9843050, R9843051 User Manual

Ser ver Upgrade Kit for Barco iQ Pro

Installation Manual

R9843050
R9843051

R5976950/00
15/02/2006

Barco nv Presentations

aan 5, 8520 Kuurne

Noordl
Phone: [phone]
Fax: [phone]

[e-mail]

E-mail:
Visit us at the web: www.barco.com

PrintedinBelgium

1. KIT DESCRIPTION

Overview

• Description

• Kit contents

1.1 Description

Introduction

In order to increase s erver performance, a new serve r upgrade kit has been developed for the following projectors :

• iQ Pro G350

• iQ Pro R350

• iQ Pro G500

• iQ Pro R500
The new server is ETX based and is specified as follows:

CPU Pentium M1.6 G hz
RAM 512

1. Kit description

Harddisk

The new server w orks only in comb

In case of an SBC kit with numb er R9843051 please contact Barco.

1.2 Kit contents

Contents

Support plate

40Gb

ination with projector firmware V3.00 or higher.

Description Image

Fan grid image 1-1

SBC

Front plate

Manual

image 1-2

-

image 1-3

-

R5976950 SERVER UPGRADE KIT FOR BARCO IQ PRO 15/02/2006 1

1. Kit description

Image 1-1

Image 1-2

Image 1-3

2 R5976950 SERVER UPGRADE KIT FOR BARCO IQ PRO 15/02/2006

2. KIT INSTALLATION

Installation

The installation of the new server involves different steps (explained in detail further on).

1. Physical installation, see procedure below

2. Performing the upgrade tool (see InfoT640)

3. Firmware upgrade to V3.00 (see InfoT640)

4. Adaptation of the video input board, see procedure below

CAUTION: Prior to firmware upgrade, th e upgrade tool must be performed, read InfoT640

Not all the procedures are explained in detail, refer to the service manual for detailed procedures.

2.1 Removing the Server

2. Kit installation

CAUTION: Wear a wrist band which is connected to the ground while handling the electrostatic discharge

sensitive parts.

How to remove the Server ?

1. Remove the input box,

2. Remove the screws at the front

Image 2-1

3. Removethesidescrew

R5976950 SERVER UPGRADE KIT FOR BARCO IQ PRO 15/02/2006

3

2. Kit installation

Image 2-2
side screw

4. Take the server out of the input box

Image 2-3
Server removed from the input box

2.2 Removing the video inputs (layer 1 and layer 2)

How to remove the video inputs ?

1. Refer to the service manual for the detailed p

rocedure

2.3 Video Board adaptation

What has to be done ?

To avoid disturbances on video sources when the new SBC is active, the hum circuit of the video board has to be disabled (pertur­bations induced by SBC supply voltage). This can be done by unsoldering the resistors R71 and R80 (see procedure below).

The video board is the board located on layer 1. For more information on how to remove this board refer to
the service manual.

How to adapt the board ?

1. Unsolder the indicated resistors.

4

R5976950 SERVER UPGRADE KIT FOR BARCO IQ PRO 15/02/2006

2. Kit installation

Image 2-4
Resistor R80 location.

R5976950 SERVER UPGRADE KIT FOR BARCO IQ PRO 15/02/2006 5

2. Kit installation

Image 2-5
Resistor R71 location.

(un)Solder tips

• Insure that the Soldering Iron Tip is clean, in good condition and is fully inserted into the heater.

• Use the appropriate Tip and Temperature.

• Do not exert force on the land (pad) during the (un)soldering operation. Damaged or lifted pads may result.

•Maxi

mize the TIP to solder joint heat transfer by m elting a small amount of solder on the Tip before contact is made.

ION

CAUT

: Proceed with caution when (un)soldering a SMD component.

2.4 Replacing the power fan grid

What has to be done ?

To allow optimal operation of the new server the fan grid mounted on the power box has to be replaced.
The input box being removed, the power box (and thus the grid) can be easily accessed.

How to change the power fan grid ?

sen the 4 screws fixing the grid to the power box and remove the grid.

1. Loo

6

R5976950 SERVER UPGRADE KIT FOR BARCO IQ PRO 15/02/2006

Image 2-6

2. Place the new grid and tighten the screws.

2. Kit installation

2.5 Reassembling the input box

How to mount the Video inputs (layer 1 and layer 2) on the new front plate ?

1. Perform above removal procedure in the reverse directions

How to mount the support plate ?

1. Loosen all the side screws fixing the boards.

Image 2-7
The image is only intended to show where the plate must be mounted, (image does not reflect the reality since it shows a third layer (optional) which is not applicable when
using a server).

2. Mount the plate and fix it with the previously rem oved screws.

How to mount the server ?

1. Mount the server in the input box and mount the input box in the projector.

R5976950 SERVER UPGRADE KIT FOR BARCO IQ PRO 15/02/2006

7

2. Kit installation

Note that the PCMCIA input plate (little openingplatemounted on the PCMCIA input) is not delivered with the
new front plate. Therefore remove it from the old fro nt plate (by removing the 2 small screws) and mount it
on the new front plate.

8 R5976950 SERVER UPGRADE KIT FOR BARCO IQ PRO 15/02/2006