Barco R9002370, R9002379 OWNER'S MANUAL

PLEASE READ

We are in no way responsible for the contents of the manual. We do not guarantee its accuracy and we do not make any claim of copyright. The copyright remains the property of their respective owners.

Visit the site to read the latest projector news and reviews, read and comment on projector specifications, download user manuals and much more.

CINE 6

R9002370 R9002379

OWNER'S MANUAL

BARCO PROJECTION SYSTEMS

CINE 6

R9002370 R9002379

OWNER'S MANUAL

Date : 01052000 Rev : 01 Art. No. : R5975809

Federal communication commission (FCC statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules and EN55022. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Instructions to the user :

If this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the following measures :

- Re-orientation of the receiving antenna for the radio or television.

- Relocate the equipment with respect to the receiver.

- Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.

- Fasten cables connectors to the equipment by mounting screws.

Note : The use of shielded cables is required to comply within the limits of Part15 of FCC rules and EN55022.

Due to constant research, the information in this manual is subject to change without notice.

Trademarks are the rights of their respective owners.

BARCO n.v./Projection Systems

Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visit Barco at the web : http://www.barco.com

Printed in Belgium

Table of Contents

SAFETY INSTRUCTIONS .................................................................................................................................................... 1-1

On safety ......................................................................................................................................................................1-2

On installation ............................................................................................................................... ............................... 1-3

On servicing ................................................................................................................................................................. 1-3

On cleaning .................................................................................................................................................................. 1-3

On repacking ................................................................................................................................................................ 1-3

On illumination ............................................................................................................................... .............................. 1-3

LOCATIONS AND FUNCTIONS OF CONTROL ................................................................................................................. 2-1

Rear Panel Terminology ............................................................................................................................................. 2-1

Front Panel Terminology ............................................................................................................................................ 2-1

Control Panel Terminology ............................................................................................................................... .......... 2-2

a. Local keypad ................................................................................................................ ........................................... 2-2

b. RCU control panel terminology ............................................................................................................................. 2-2

CONNECTIONS ................................................................................................................................................................... 3-1

Power (mains) cord connection ................................................................................................................................ 3-1

Switching on / off ........................................................................................................................................................3-1

Signal input to the projector ...................................................................................................................................... 3-1

Connecting a Composite Video source.................................................................................................................... 3-1

Connecting a S-Video source .................................................................................................................................... 3-2

Connecting a RGB Analog source with composite sync ....................................................................................... 3-2

Connecting a Component Video source .................................................................................................................. 3-3

Connecting a RF signal (optional) .............................................................................................. .............................. 3-3

Peripheral equipment.................................................................................................................................................. 3-4

Connecting a RCVDS 05 switcher ............................................................................................................................ 3-4

Connecting a VS05 switcher ...................................................................................................................................... 3-4

Connecting an IR Remote Receiver ......................................................................................................................... 3-4

TABLE OF CONTENTS

CONTROLLING ................................................................................................................................................................... 4-1

Battery installation in the RCU .................................................................................................................................. 4-1

How to use the RCU ............................................................................................................. ..................................... 4-2

Projector Address ............................................................................................................................... ...................... 4-2

How to Display a Projector Address ......................................................................................................................... 4-2

How to Program an Address into the RCU?........................................................................................................... 4-3

Input selection............................................................................................................................... ............................... 4-3

Picture controls ............................................................................................................... ............................................. 4-4

The Pause key .................................................................................................................. ........................................... 4-5

Sound control with the RCU (optional) .................................................................................................................. 4-5

START UP OF THE ADJUSTMENT MODE ................................................................................................ ....................... 5-1

Adjustment Mode ......................................................................................................................................................... 5-1

RANDOM ACCESS ADJUSTMENT MODE ........................................................................................................................ 6-1

Starting up the Random Access Adjustment Mode ................................................................................................ 6-1

Overview 'Random Access Adjustment Mode' ......................................................................................................... 6-1

Selecting Setup Pattern .............................................................................................................................................. 6-2

Internal Cross-Hatch Pattern............................................................................................................................... ....... 6-2

Selection Menu ................................................................................................................. ........................................... 6-2

Picture Tuning ................................................................................................................. ............................................. 6-2

Color Balance .............................................................................................................................................................. 6-3

Gamma ............................................................................................................................... .......................................... 6-3

Decoding ...................................................................................................................................................................... 6-3

Color Select ................................................................................................................................................................. 6-4

Geometry adjustments ............................................................................................................................... ................. 6-4

Horizontal Phase adjustment............................................................................................................................... ...... 6-5

R5975809 BARCO CINE 6 ____________________________________________________________________________________ i-1

Table of Contents

TABLE OF CONTENTS

Raster Shift Adjustment .............................................................................................................................................. 6-5

East-West (Left-Right) adjustments .......................................................................................................................... 6-7

North-South (Top-Bottom) adjustments .................................................................................................................... 6-8

Horizontal & Vertical Size adjustment ....................................................................................................................... 6-9

Vertical Linearity Adjustment ...................................................................................................................................... 6-9

Blanking adjustment ............................................................................................................................... .................. 6-10

Convergence Adjustment .......................................................................................................................................... 6-11

SERVICE MODE ................................................................................................................................................................. 7-1

Starting up the Service Mode ..................................................................................................................................... 7-1

Overview flowchart 'Service' mode .............................................................................................. ............................... 7-1

Projector Set-up ............................................................................................................................... ............................ 7-2

Identification .................................................................................................................................................................7-2

Total Run Time ............................................................................................................................................................ 7-3

Change Password ....................................................................................................................................................... 7-3

Change Language ....................................................................................................................................................... 7-3

Change Projector Address ......................................................................................................................................... 7-4

Change baud rate .......................................................................................................................................................7-4

Power up mode ........................................................................................................................................................... 7-5

Barco Logo ...................................................................................................................................................................7-5

Memory Management ............................................................................................................................... ................... 7-5

Copy a Block ................................................................................................................... ............................................. 7-6

Deletion of Blocks .......................................................................................................................................................7-6

Deleting Block by Block ..............................................................................................................................................7-6

Deletion of all Blocks .................................................................................................................................................. 7-6

All Settings to midpos ......................................................................................................... ....................................... 7-7

Undo All settings to Midpos ....................................................................................................................................... 7-7

R&B Convergence Mid ............................................................................................................ .................................... 7-8

Uno R&B Convergence Mid ....................................................................................................................................... 7-8

Common Settings........................................................................................................................................................ 7-9

G2-adjustment.............................................................................................................................................................. 7-9

Crt run in cycle ............................................................................................................... ............................................. 7-9

Projector Warm Up .............................................................................................................. ..................................... 7-10

CRT Drive Mode ........................................................................................................................................................7-10

Memory Bank ............................................................................................................................... .............................. 7-10

Adjustment for removing horizontal centre line...................................................................................................... 7-11

OPTIONS ............................................................................................................................................................................ 8-1

IR Receiver 800 ........................................................................................................................................................... 8-1

Hardwired RCU ............................................................................................................................... ............................ 8-1

RCVDS 05 Source Selector ....................................................................................................................................... 8-2

VS05 Switcher .................................................................................................................. ............................................ 8-2

Adapter and communication cables .......................................................................................................................... 8-2

Ceiling Mount CM50 ............................................................................................................................... ..................... 8-2

Tuner kit ...................................................................................................................... ................................................. 8-2

APPENDIX A : TUNER MODE ....................................................................................................................................... A-1

Tuner Mode ..................................................................................................................................................................A-1

How to activate the tuner mode ................................................................................................................................ A-1

Tuner Set-up ................................................................................................................... ............................................. A-2

Broadcasting System .................................................................................................................................................. A-2

Auto Search ..................................................................................................................................................................A-3

Manual Search ............................................................................................................................................................. A-3

Organise Channel List ............................................................................................................................................... A-4

Bilingual ............................................................................................................................... ......................................... A-5

Teletext ....................................................................................................................... ................................................... A-5

i - 2 ____________________________________________________________________________________ R5975809 BARCO CINE 6

Safety Instructions

Notice on Safety

This equipment is built in accordance with the requirements of the international safety standards IEC 950, EN 60950, UL 1950 and CSA C22.2 No 950 which are the safety standards of information technology equipment including electrical business equipment.

These safety standards impose important requirements on the use of safety critical components, materials and isolation, in order to protect the user or operator against risk of electric shock and energy hazard, and having access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of fire.

Simulated single fault condition testing ensures the safety of the equipment to the user even when the equipment's normal operation fails.

INSTALLATION INSTRUCTIONS

Before operating this equipment please read this manual thoroughly, and retain it for future reference. Installation and preliminary adjustments should be performed by qualified BARCO personnel or by authorized BARCO service dealers.

OWNERS RECORD

The part number and serial number are located at the left side of the projector. Record these numbers in the spaces provided below. Refer to them whenever you call upon your BARCO dealer regarding this product.

SAFETY INSTRUCTION

PART NUMBER :

SER. NUMBER :

DEALER :

Safety indication on the product

The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk of electrical shock to persons.

The exclamation point within a triangle is intended to tell the user that important operating and/or servicing instructions are included in the technical documentation for this equipment.

WARNING

TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO

NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE

R5975809 BARCO CINE 6 ___________________________________________________________________________________ 1-1

Safety Instructions

FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT)

This equipment has been tested and found to comply with the limits of a class A digital device, pursuant to Part 15 of the FCC Rules and EN55022.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Note : The use of shielded cables is required to comply within the limits of Part 15 of FCC rules and EN55022

µ All the safety and operating instructions should be read before using this unit. µ The safety and operating instructions manual should be retained for future reference. µ All warnings on the equipment and in the documentation manuals should be adhered to. µ All instructions for operating and use of this equipment must be followed precisely.

On safety

1. This product should be operated from an AC power source

Operating AC power voltage of the projector:

BARCO CINE 6 : Art. No. R9002370 (230 V AC)

The projector leaves the factory for 230 V AC. Consult your dealer to switch over to 120 V AC. If you are not sure of the type of AC power available, consult your dealer or local power company.

2. This product is equipped with a 3-wire grounding plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.

WARNING FOR THE CUSTOMERS : THIS APPARATUS MUST BE GROUNDED (EARTHED) via the supplied 3 conductor AC power cable. (If the supplied power cable is not the correct one, consult your dealer.)

Art. No. R9002379 (120 V AC)

A. Mains lead (Power cord) with CEE 7 plug: The wires of the mains lead are colored in accordance with the following code.

Green & Yellow : Earth (safety earth) Blue : Neutral Brown : Line (live)

B. Power cord with ANSI 73.11 plug:

The wires of the power cord are colored in accordance with the following code.

Green / Yellow : Ground White : Neutral Black : Line (live)

3. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself.

4. If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord ampere rating. Also make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.

5. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock.

Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before resuming operations.

6. Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the projector due to lightning and AC power-line surges.

1 - 2 ___________________________________________________________________________________ R5975809 BARCO CINE 6

Safety Instructions

On installation

1. Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it.

2. Do not use this equipment near water.

3. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable operation of the

product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.

This product should never be placed near or over a radiator or heat register. The projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.

On servicing

Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potential and risk of electric shock!

Refer all servicing to qualified service personnel. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions :

a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the equipment. c. If the product has been exposed to rain or water. d. If the product does not operate normally when the operating instructions are followed. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in performance, indicating a need for service.

Note : Adjust only those controls that are covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

Replacement parts - When replacement parts are required, be sure the service technician has used original BARCO replace-

Safety check - Upon completion of any service or repairs to this projector, ask the service technician to perform safety

On cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

- To keep the cabinet looking brand-new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution. Never use strong solvents, such as thinner or benzene, or abrasive cleaners, since these will damage the cabinet.

- To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective coating, therefore, avoid touching the lens.To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.

On repacking

Save the original shipping carton and packing material; they will come in handy if you ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory.

On illumination

ment parts or authorized replacement parts which have the same characteristics as the BARCO original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty.

checks to determine that the product is in proper operating condition.

In order to obtain the best quality for the projected image, it is essential that the ambient light which is allowed to fall on the screen be kept to an absolute minimum.

When installing the projector and screen, care must be taken to avoid exposure to ambient light directly on the screen. Avoid adverse illumination on the screen from direct sunlight or fluorescent lighting fixtures.

The use of controlled ambient lighting, such as incandescent spot light or a dimmer, is recommended for proper room illumination. Where possible, care should also be taken to ensure that the floors and walls of the room in which the projector is to be installed are non-reflecting, dark surfaces. Brighter surfaces will tend to reflect and diffuse the ambient light and hence reduce the contrast of the projected image on the screen.

R5975809 BARCO CINE 6 ___________________________________________________________________________________ 1-3

Safety Instructions

1 - 4 ___________________________________________________________________________________ R5975809 BARCO CINE 6

Locations and Functions of Controls

LOCATION AND FUNCTION OF CONTROLS

REAR PANEL TERMINOLOGY

1. Communication port (800 peripherals)

- allows communication between the RCVDS switcher and the projector.

- allows connection of a remote IR receiver unit to the projector.

2. IR Remote - Remote input for wired remote control

3. IR sensor - Receiver for control signals transmitted from the RCU.

4. RGB-S IN or (R-Y)Y(B-Y)-S IN ( 5 x BNC connector ) :

RGB-S in : allows a character generator, microcomputer, video camera, etc. having analog RGB output to be connected to the projector.

Line inputs : - signals RED-GREEN-BLUE

5. VIDEO IN ( Composite video, 1 x BNC) connector allows a video tape recorder, video camera, color receiver/monitor, etc. having video line output to be connected to the projector.

- COMPOSITE sync. signal or Hor. sync

- Vertical sync

6. S-VIDEO IN: Separated Y/C (luma-chroma) signal inputs and outputs for higher quality playback of Super VHS signals. (4- pin S-VIDEO connector).

7. Auto diagnosis display STD BY / NORMAL

8. Local key Pad

9. Power (Mains) Switch: Depending on the software set-up of the projector during installation, the projector switches to

'standby' or to 'operational mode'. If in standby, the standby led in the autodiagonosis display lights up.

10. Power (Mains) input: Connect the supplied AC power (mains) cord here and to the wall outlet.

11. Audio Output : Only if the Tuner option is installed. Audio out to be connected to audio amplifier.

12. RF input : Only if the Tuner option is installed. Input for RF signals from a TV cable network or TV antenna.

13. RS 232 : Allows connection to the serial port of a Computer for controlling the projector.

Front Panel Terminology

PAUSE COINCIDENCE EHT HOLD DOWN IR CODE RXD

1. IR SENSOR : Receiver for control signals transmitted from the RCU.

2. IRIS Camera : ( optional )

R5975809 BARCO CINE 6 ___________________________________________________________________________________ 2-1

Locations and Functions of Control

Control panel terminology

a. The local keypad

The local keypad is at the rear side of the projector.

b. RCU control panel terminology

This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set-up. It includes automatic storing of :

- picture controls (Brightness, Sharpness,....)

- picture geometry adjustments

- convergence adjustments

Other functions of the remote control are:

- switching between standby and operational modes

- switching to "pause" (blanked picture, full power for immediate restarting)

- direct access to all connected sources

- variable adjustment speed : when pushing continuously on the arrow keys or the picture keys, the adjustment will be executed in an accelerated fashion.

RCU

ADJUST

Local Keypad

EXIT

STANDBY

ENTER

415

stand-by

pause/park

sharpness

tint

2 - 2 ___________________________________________________________________________________ R5975809 BARCO CINE 6

color

brightness

contrast

Locations and Functions of Controls

Star Key : When a RF-tuner is built in (option), this is used to toggle between Video and tuner signal.

ADJ. : adjust key, to enter or exit the adjustment mode.

Address key (sunk key) : to enter the address of the projector (between 0 and 9). Press the address key, followed

STBY : stand by button : - to initiate remote power up operation

Pause : to blank the image, press PAUSE. The image disappears but full power is retained for

Mute : The picture stays while the audio is turned off. The power for the amplifiers stays.

Help : On line help information (not yet available)

Digit buttons : Direct input selection

Audio control : use these buttons to obtain the desired level (see also 'Controlling') for each audio

by pressing one digit button between 0 and 9.

- to stop projection without main power off.

immediate restarting.

function

Picture controls : use these buttons to obtain the desired level (see also 'Controlling') for each picture

TEXT : During Video or RGB operations : when adjusting one of the image controls, the displayed

Freeze : When in teletext mode, (only when the tuner options installed) this key is used to freeze

Enter : to start up the adjustment mode or to confirm an adjustment or selection in the adjustment

Exit : to leave the adjustment mode or to go back to the previous menu when in the adjustment

Control keys : to make menu selections when in the adjustment mode. Also allows to increment or

RC operating indication : lights up when a button on the remote control is pressed. (This is a visual indicator to

function.

bar scale can be removed by pressing 'TEXT' key first. To re-display the bar scale on the screen, press 'TEXT' key again. 'TEXT' key is only active in operational mode. When 'TEXT' key is off, no warning message will be displayed. When in Tuner mode : this key is used to activate teletext.

the actual page.

mode.

decrement an adjustment in the adjustment mode.

= up arrow in the menus.

= down arrow in the menu.

= right arrow in the menus.

= left arrow in the menus.

check the operation of the remote control).

Function keys : Direct access keys for certain menu functions.

R5975809 BARCO CINE 6 ___________________________________________________________________________________ 2-3

Locations and Functions of Control

2 - 4 ___________________________________________________________________________________ R5975809 BARCO CINE 6

Connections

1234

Power (mains) cord connection

Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector on the rear of the projector.

Switching on/off

The projector is switched ON and OFF using the power (mains) switch ON/OFF. Pressed : ON Not pressed : OFF The projector can start now in the 'operational mode' (image displayed) or in the 'stand by mode', depending on the software setting in the service menu of the projector . This is done during installation by a qualified technician. If you want to change this start up mode, call a qualified technician.

Stand by indication lamp :

No light up : Projector in operational mode Red : Projector is in stand by.

Leds on the rear plate of the projector

CONNECTIONS

STDBY / NORMAL PAUSE COINCIDENCE EHT HOLDOWN IR RECVD

Signal input connection to the projector :

- Composite Video

- S-Video

- RGB

- YUV (component input)

Note : All sync types accepted and Muse HDTV Standard accepted.

Source No Projector input Press digit

1 Comp. Video 1 2 S-Video* 2 3 RGB/15K/32K 3 4 HDTV(Gs) 4

Muse 5 YUV 5 6 YUV on HDTV 6

* Input signal Y/C (luma/chroma) On RGB/YUV/Gs/H,V sep /Gs /CS on both Pol accepted

Connecting a Composite Video source

Composite video signals from a VCR, OFF air signal, decoder, etc.

Composite Video

TV Tuner

VCR

R5975809 BARCO CINE 6 ___________________________________________________________________________________ 3-1

Audio

Amplifier

Connections

Video input selection

a. with the RCU : press digit 1

b. with the local keypad

- press ADJUST key, the GENERAL ACCESS menu is displayed on the screen

- use the control keys to highlight 1

- press ENTER to select the highlighted source

Connecting a S-Video to port 2.

Separate Y-luma/C-chroma signals for higher quality playback of S-VHS signals.

GENERAL ACCESS

5 6 3 4 1 2

Enter ADJUST

Select with

then <ENTER>

<EXIT> to return

BRIGHTNESS

CONTRAST

Luma / Chroma

VCR

S - VHS

Audio Amplifier

Input selection

a. with the RCU : press digit 2

b. with the local keypad :

- press ADJUST key, the GENERAL ACCESS menu is displayed on the screen

- use the control keys to highlight 2

- press ENTER to select the highlighted source.

GENERAL ACCESS

5 6 3 4 1 2

Enter ADJUST

Select with

then <ENTER>

<EXIT> to return

BRIGHTNESS

CONTRAST

Connecting a RGB Analog source with composite sync.

RGB analog input terminals with composite sync input or with sync on green or separate sync. The projector detects automatically where the sync signal is located. It accepts RGB at 15 and 32 K. Always use an interface when a computer and local monitor have to be connected to the projector. Examples of interfaces which can be applied :

Universal analog interface: R9826100

3 - 2 ___________________________________________________________________________________ R5975809 BARCO CINE 6

Connections

RGBs (or RGsB) input selection

a. press digit 3 on the RCU

b. with the local keypad :

- press ADJUST key, the GENERAL ACCESS menu is displayed on screen

- use the control keys to highlight 3

- press ENTER to select the highlighted source.

Connecting a Component source

YUV analog input terminals with sync input or with sync on the luminance (Y) input.

GENERAL ACCESS

5 6 3 4 1 2

Enter ADJUST

Select with

then <ENTER>

<EXIT> to return

BRIGHTNESS

CONTRAST

VCR

Audio Amplifier

YsUV or YUVS selection

a. with the RCU : press digit 5 for YUV

b. with the local keypad

- press ADJUST key, the GENERAL ACCESS menu is displayed on the screen

- use the control keys to highlight 5

- press ENTER to select the highlighted source

- for YUV at HDTV Standard select 6

Connecting a RF signal to the projector (optional) :

The projector automatically determines the presence of a tuner. Connect the RF signal to the RF input of the projector. Connect the audio output to an audio amplifier.

GENERAL ACCESS

5 6 3 4 1 2

Enter ADJUST

Select with

then <ENTER>

<EXIT> to return

BRIGHTNESS

CONTRAST

TV Antenna or Cable Network

Audio Amplifier

R5975809 BARCO CINE 6 ___________________________________________________________________________________ 3-3

Connections

To select the tuner option : (only when tuner card is added)

a. Press the STAR key on the RCU to activate the tuner mode

b. With the local keypad :

- Press ADJUST key to display the GENERAL ACCESS menu on the screen.

- Use the control keys to highlight 'TUNER'.

- Press ENTER to activate the tuner mode.

GENERAL ACCESS

5 6 3 4 1 2 TUNER

Enter ADJUST

Select with

then <ENTER>

<EXIT> to return

BRIGHTNESS

CONTRAST

Peripheral equipment

Connecting a RCVDS 05 switcher to the projector.

- Up to 10 inputs (20 inputs when video and S-Video) with the RCVDS 05 switcher and up to 90 inputs when 10 RCVDS switchers are linked via the expansion modules.

- Serial communication with the projector.

- Remote control buttons on the RCVDS to control the projector (source selection and analog settings).

- The selected source number will be displayed on a 2 digit display and the selected input modules will be indicated with a LED on the rear.

For more information about the use of the RCVDS 05, consult the Owner's Manual, Order No. R5975765.

Connecting a VS05 switcher to the projector.

The VS05 can switch up to 5 Composite Video sources, 3 S-Video sources and 1 RGB analog or component video source to the projector. In addition, the audio signal from the source can be switched to an audio amplifier. Order No. R9827890.

For more information about the use of the VS05, consult the Owner's Manual, Order No. R5975245.

Connecting an IR Remote Receiver to the Projector.

This infra-red receiver makes it possible to control the projector from another room. There is a communication cable between the IR receiver and the projector or the RCVDS. The infrared control information from the RCU is sent to the IR Remote Receiver. The IR Remote Receiver 800 displays the selected source on a 7-segment display. Order No. R9827515.

3 - 4 ___________________________________________________________________________________ R5975809 BARCO CINE 6

+ 44 hidden pages