Page 1
DATA
708
R9002120
OWNER'S MANUAL
Page 2
Page 3
BARCO PROJECTION SYSTEMS
Date :
260597
DATA
708
R9002120
OWNER'S MANUAL
Art. No. :
R5975977
Page 4
Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, May 1997.
All rights reserved.
Trademarks are the rights of their respective owners.
BARCO nv/Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Printed in Belgium
Page 5
Table of Contents
TABLE OF CONTENTS
i
TABLE OF CONTENTS ...................................................................................................1
SAFETY INSTRUCTIONS............................................................................................ 1-1
On safety........................................................................................................................................1-1
On installation ................................................................................................................................1-2
On servicing ................................................................................................................... ................ 1-2
On cleaning .................................................................................................................................... 1-2
On repacking................................................................................................................... ............... 1-2
On illumination................................................................................................................................1-2
LOCATION AND FUNCTION OF CONTROLS ............................................................ 2-1
Rear Panel Terminology................................................................................................................. 2-1
Front Panel Terminology ................................................................................................................2-1
Control panel terminology...............................................................................................................2-2
CONNECTIONS ........................................................................................................... 3-1
Switching on/off .............................................................................................................................. 3-1
Signal input connection to the projector : ........................................................................................3-1
Power (mains) cord connection .................................................................................................. .... 3-1
Connecting a Composite Video source........................................................................................... 3-2
Connecting a S-Video or Video source to Port 2............................................................................ 3-3
Connecting a RGB Analog source with composite sync.................................................................. 3-4
Connecting a RGB Analog source with Tri-level sync. .................................................................... 3-4
Connecting a Component source. ..................................................................................................3-5
Connecting a Component source with Tri-level sync.......................................................................3-5
Connecting a computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS232 input of
the projector. .................................................................................................................................. 3-6
Connecting a RCVDS 05 switcher to the projector.......................................................................... 3-6
Connecting a VS05 switcher to the projector. ................................................................................. 3-6
Connecting an IR Remote Receiver to the projector ...................................................................... 3-6
Peripheral equipment ..................................................................................................................... 3-6
CONTROLLING............................................................................................................ 4-1
Battery installation in the RCU. ....................................................................................................... 4-1
How to use the RCU....................................................................................................................... 4-2
Projector address ...........................................................................................................................4-2
How to display a projector address?...............................................................................................4-2
How to program an address into the RCU? ....................................................................................4-3
Input selection ................................................................................................................................ 4-3
Picture controls ..............................................................................................................................4-4
The Pause key. .............................................................................................................................. 4-4
5975977 BARCODATA 708 260597
i-1
Page 6
Table of Contents
START UP OF THE ADJUSTMENT MODE..................................................................5-1
Adjustment mode ...........................................................................................................................5-1
Starting up the random access adjustment mode. .......................................................................... 6-1
RANDOM ACCESS ADJUSTMENT MODE..................................................................6-1
Overview 'random Access Adjustment' mode. ................................................................................ 6-1
Selecting Setup Pattern..................................................................................................................6-2
Internal Cross Hatch Pattern .......................................................................................................... 6-2
Random access adjustment mode selection menu. ........................................................................6-3
Picture Tuning ................................................................................................................................ 6-3
Color Balance................................................................................................................................. 6-3
Sync Fast/Slow Adjustment ...................................................................................................... ...... 6-3
Line Doubler (option) ......................................................................................................................6-4
Port 2 : S-Video/Video .................................................................................................................... 6-4
Peaking ..........................................................................................................................................6-4
Color Select.................................................................................................................................... 6-4
Geometry Adjustments ................................................................................................................... 6-5
Horizontal Phase Adjustment ......................................................................................................... 6-5
Raster Shift Adjustment..................................................................................................................6-6
Left-Right (east-west) Adjustments................................................................................................. 6-7
Top-Bottom (north-south) Adjustments ........................................................................................... 6-8
Size Adjustment ............................................................................................................................. 6-9
Vertical Linearity Adjustment .......................................................................................................... 6-9
Blanking Adjustments ...................................................................................................................6-10
Convergence Adjustment ......................................................................................................... .... 6-11
SERVICE MODE ..........................................................................................................7-1
Starting up the Service mode. ........................................................................................................7-1
Overview flowchart 'Service' mode. ................................................................................................ 7-1
Projector Set-up ............................................................................................................................. 7-2
Identification ................................................................................................................................... 7-2
Total Run Time............................................................................................................................... 7-3
Change password .......................................................................................................................... 7-3
Change Language..........................................................................................................................7-3
Change Projector Address ............................................................................................................. 7-4
Change baudrate............................................................................................................................7-4
Power up mode .............................................................................................................................. 7-4
BARCO_logo.................................................................................................................................. 7-5
Memory management..................................................................................................................... 7-5
Copy a block ................................................................................................................... ............... 7-6
Deletion of blocks ...........................................................................................................................7-6
Deleting block by block...................................................................................................................7-6
Deletion of all blocks ......................................................................................................... ............. 7-7
All settings to midposition ............................................................................................................... 7-7
Undo all settings to midpos............................................................................................................. 7-7
R & B convergence mid..................................................................................................................7-8
Undo R & B convergence mid ........................................................................................................ 7-8
Green convergence mid .................................................................................................................7-8
Undo green convergence mid..................................................................................................... .... 7-8
Common Settings...........................................................................................................................7-9
G2 Adjustment ............................................................................................................................... 7-9
CRT run in cycle............................................................................................................................. 7-9
Projector warm up ........................................................................................................................ 7-10
CRT Drive Mode .......................................................................................................................... 7-10
I2C Diagnostics ............................................................................................................................ 7-11
i-2 5975977 BARCODATA 708 260597
Page 7
Table of Contents
MESSAGES, WARNINGS AND FAILURES................................................................. 8-1
OPTIONS ..................................................................................................................... 9-1
IR Receiver 800 .............................................................................................................................9-1
Hardwired RCU. ............................................................................................................................. 9-1
Projector Control software .............................................................................................................. 9-1
RCVDS 05 Source Selector............................................................................................................ 9-1
VS05 Switcher................................................................................................................................ 9-1
IRIS/2 Auto-Convergence System ................................................................................................. . 9-1
MAGIK Interface.............................................................................................................................9-2
Adapter and communication cables................................................................................................ 9-2
Orbiting Kit .....................................................................................................................................9-2
Line Doubler Kit.............................................................................................................................. 9-2
Ceiling mount CM50 .......................................................................................................................9-2
Soft edge matching kit .................................................................................................................... 9-2
Contrast modulation kit...................................................................................................................9-2
APPENDIX A : ADJUSTMENT BLOCKS AND SOURCE NUMBERS 90 - 99.............. A-1
Adjustment Blocks (memory blocks)...............................................................................................A-1
Source numbers 90 - 99 .................................................................................................................A-1
5975977 BARCODATA 708 260597
i-3
Page 8
Table of Contents
i-4 5975977 BARCODATA 708 260597
Page 9
Safety Instructions
1
SAFETY INSTRUCTIONS
Notice on Safety
This equipment is built in accordance with the requirements of the
international safety standards EN60950, UL 1950 and CSA C22.2
No.950, which are the safety standards of information technology
equipment including electrical business equipment.
These safety standards impose important requirements on the use of
safety critical components, materials and isolation, in order to protect
the user or operator against risk of electric shock and energy hazard,
and having access to live parts.
Safety standards also impose limits to the internal and external
temperature rises, radiation levels, mechanical stability and strength,
enclosure construction and protection against the risk of fire.
Simulated single fault condition testing ensures the safety of the
equipment to the user even when the equipment's normal operation
fails.
INSTALLATION INSTRUCTIONS
Before operating this equipment please read this manual
thoroughly, and retain it for future reference.
Installation and preliminary adjustments should be performed
by qualified BARCO personnel or by authorized BARCO
service dealers.
WARNING
TO PREVENT FIRE OR ELECTRICAL SHOCK
HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE
FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT)
This equipment has been tested and found to comply with the limits
of a class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Note :
The use of shielded cables is required to comply within the limits of
Part 15 of FCC rules and EN55022.
* All the safety and operating instructions should be read before using
this unit.
* The safety and operating instructions manual should be retained for
future reference.
OWNER’S RECORD
The part number and serial number are located at the back side of the
projector. Record these numbers in the spaces provided below.
Refer to them whenever you call upon your BARCO dealer regarding
this product.
PART NUMBER :
SER. NUMBER :
DEALER :
The lightning flash with an arrowhead within a
triangle is intended to tell the user that parts
inside this product may cause a risk of electrical
shock to persons.
The exclamation point within a triangle is intended to tell the user that important operating
and/or servicing instructions are included in the
technical documentation for this equipment.
5975977 BARCODATA 708 260597
* All warnings on the equipment and in the documentation manuals
should be adhered to.
* All instructions for operating and use of this equipment must be
followed precisely.
On safety
1. This product should be operated from an AC power source.
This projector may be connected to an IT-power system.
Operating AC power voltage of the projector:
BARCODATA 708
Art.No. R9002120 (
Consult your dealer to switch over from 230Vac to 120 Vac or from
120Vac to 230 Vac.
If you are not sure of the type of AC power available, consult your
dealer or local power company.
2. This product is equipped with a 3-wire grounding plug, a plug
having a third (grounding) pin. This plug will only fit into a groundingtype power outlet. This is a safety feature. If you are unable to insert
the plug into the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the purpose of the grounding-type
plug.
WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE
GROUNDED (EARTHED) via the supplied 3 conductor AC power
cable.
(If the supplied power cable is not the correct one, consult your
dealer.)
230V AC
)
1-1
Page 10
Safety Instructions
A. Mains lead (Power cord) with CEE 7 plug:
The wires of the mains lead are colored in
accordance with the following code.
Green and yellow: earth (safety earth)
Blue: neutral
Brown: line (live)
B. Power cord with ANSI 73.11 plug:
The wires of the power cord are colored in
accordance with the following code.
Green/yellow: ground
White: neutral
Black: line (live)
3. Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.
To disconnect the cord, pull it out by the plug. Never pull the cord
itself.
4. If an extension cord is used with this product, make sure that the
total of the ampere ratings on the products plugged into the extension
cord does not exceed the extension cord ampere rating. Also make
sure that the total of all products plugged into the wall outlet does not
exceed 15 amperes.
5. Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electrical shock.
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the equipment.
c.If the product has been exposed to rain or water.
d. If the product does not operate normally when the operating
instructions are followed.
Note : Adjust only those controls that are covered by the operating
instructions since improper adjustment of the other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance, indicating
a need for service.
Replacement parts - When replacement parts are required, be sure
the service technician has used original BARCO replacement parts or
authorized replacement parts which have the same characteristics as
the BARCO original part. Unauthorized substitutions may result in
degraded performance and reliability, fire, electric shock or other
hazards. Unauthorized substitutions may void warranty.
Safety check - Upon completion of any service or repairs to this
projector, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
On cleaning
Never spill liquid of any kind on the product. Should any liquid or solid
object fall into the cabinet, unplug the set and have it checked by
qualified service personnel before resuming operations.
6. Lightning - For added protection for this video product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent
damage to the projector due to lightning and AC power-line surges.
On installation
1. Do not place this equipment on an unstable cart, stand, or table.
The product may fall, causing serious damage to it.
2. Do not use this equipment near water.
3. Slots and openings in the cabinet and the back or bottom are
provided for ventilation; to ensure reliable operation of the product
and to protect it from overheating, these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface. This
product should never be placed near or over a radiator or heat
register.
The projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
4. Do not block the projector cooling fans or free air movement under
and around the projector. Loose papers or other objects may not be
nearer to the projector than 4" on any side.
On servicing
Do not attempt to service this product yourself, as opening or
removing covers may expose you to dangerous voltage potentials
and risk of electric shock!
Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
- To keep the cabinet looking brand-new, periodically clean it with a
soft cloth. Stubborn stains may be removed with a cloth lightly
dampened with mild detergent solution. Never use strong solvents,
such as thinner or benzine, or abrasive cleaners, since these will
damage the cabinet.
- To ensure the highest optical performance and resolution, the
projection lenses are specially treated with an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens,
use a soft dry cloth. Do not use a damp cloth, detergent solution, or
thinner.
On repacking
Save the original shipping carton and packing material; they will
come in handy if you ever have to ship your equipment. For maximum
protection, repack your set as it was originally packed at the factory.
On illumination
In order to obtain the best quality for the projected image, it is essential
that the ambient light which is allowed to fall on the screen be kept to
an absolute minimum.
When installing the projector and screen, care must be taken to avoid
exposure to ambient light directly on the screen. Avoid adverse
illumination on the screen from direct sunlight or fluorescent lighting
fixtures.
The use of controlled ambient lighting, such as incandescent spot
light or a dimmer, is recommended for proper room illumination.
Where possible, care should also be taken to ensure that the floors
and walls of the room in which the projector is to be installed are nonreflecting, dark surfaces. Brighter surfaces will tend to reflect and
diffuse the ambient light and hence reduce the contrast of the
projected image on the screen.
1-2 5975977 BARCODATA 708 260597
Page 11
Location and Function of Controls
2
LOCATION AND FUNCTION OF CONTROLS
Rear Panel Terminology
RS232OUTRS232IN
IR
1
RS232IN
1
Connection between the projector and an IBM PC (or
compatible) or MAC (RS422) for remote computer control
and data communication.
RS232OUT
2
Used to connect to the next projector, RS232IN plug
(communication link for PC or MAC to the next projector)
IR sensor
3
receiver for control signals transmitted from the RCU.
3
2
COMM PORT
(800 peripherals)
4
REMOTE
5
RG(S)B
R-Y Y(S) B-Y
6 7
S-VIDEO
S
VIDEO
8
RGB-S IN or (R-Y)Y(B-Y)-S IN (4x BNC connector):
6
RGB-S in
video camera, etc. having analog RGB output to be connected to the projector.
Line inputs: - signals RED-GREEN-BLUE
(R-Y)Y(B-Y)-S IN
professional VCR having component outputs to the projector.
: allows a character generator, microcomputer,
- COMPOSITE sync. signal
(component in):allows to connect e.g. a
Communication port (800 peripherals)
4
* allows communication between the RCVDS switcher and
the projector.
* allows connection of a remote IR receiver unit to the
projector.
* allows connection of an IRIS 800 to converge the image
automatically.
IR Remote
5
remote input for wired remote control
Front Panel Terminology
1
AUTODIAGNOSIS DISPLAY
LED indication for service purposes.
-CONV
+17V
+9V
+210V
-9V
+30V
Line inputs - signals RED-LUMA, LUMA, BLUE-LUMA
VIDEO IN (Composite video, 1x BNC connector): allows a
7
video tape recorder, video camera, color receiver/monitor,
etc. having video line output to be connected to the projector.
S-VIDEO IN: Separated Y/C (luma-chroma) signal inputs
8
and outputs for higher quality playback of Super VHS signals
(4-pin S-VIDEO connector).
1
HOLD DOWN HD
COINC
SF
HOLD DOWN EHT
STANDBY
+HTHD
-17V
+CONV
2
3 4
POWER (MAINS) INPUT: Connect the supplied ac power
3
(mains) cord here and to wall the outlet.
IR SENSOR
4
receiver for control signals transmitted from the RCU700.
- COMPOSITE sync. signal
2
5975977 BARCODATA 708 260597
POWER (MAINS) SWITCH : press the switch to turn the
projector ON.
Depending on the hardware set-up of the projector during
installation, the projector switches to
‘operational mode’. If in standby, the standby led in the
autodiagnosisdisplay lights up.
‘standby’ or to
2-1
Page 12
Location and Function of Controls
Control panel terminology
a. The local keypad
Gaining access
The local keypad is covered by a door on
which the projector logo is screened.
To open this door, push as indicated on
next drawing and turn it to the front side
of the projector.
ADJUST
STANDBY
b. RCU control panel terminology
This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely.
This remote control is used for source selection, control, adaptation and set-up. It includes automatic storing of :
- picture controls (Brightness, Sharpness,....)
- picture geometry adjustments
- convergence adjustments
Other functions of the remote control are:
- switching between standby and operational modes
- switching to "pause" (blanked picture, full power for immediate restarting)
- direct access to all connected sources
- variable adjustment speed : when pushing continuously on the arrow keys or the picture keys, the adjustment will be executed in an
accelerated fashion.
EXIT
ENTER
RCU Local keypad
1
2
ADJ
3
PAUSE8TEXT
4
STBY
EXIT
ENTER
12
11
10
9
2
ADJUST
STANDBY
4 11
10
EXIT
ENTER
9
5
+
-
0
9
6
7
5
SHARPNESS
+
-
8
TINT
+
-
6
COLOR
-
BRIGHTNESS
-
CONTRAST
+
+
43
21
7
stand-by
pause/park
sharpness
tint
color
brightness
32c
contrast
2-2 5975977 BARCODATA 708 260597
Page 13
Location and Function of Controls
Back light key : when activated, all keys will be lit up and
1
visible in the dark.
ADJ. : adjust key, to enter or exit the adjustment mode.
2
Address key (recessed key), to enter the address of the
3
projector (between 0 and 9). Press the address key,
followed by pressing one digit button between 0 and 9.
STBY : stand by button :
4
5
6
7
- to initiate remote power up operation
- to stop projection without main power off.
Pause :to blank the image, press PAUSE. The image
disappears but full power is retained for immediate restarting.
Digit buttons : direct input selection.
Picture controls : use these buttons to obtain the desired
level (see also 'Controlling') for each picture function.
8
9
10
11
12
TEXT : when adjusting one of the image controls during a
meeting, the displayed bar scale can be removed by
pressing 'TEXT' key first. To re-display the bar scale on the
screen, press 'TEXT' key again. 'TEXT' key is only active
in operational mode. When 'TEXT' is off, no warning
message will be displayed.
ENTER : to start up the adjustment mode or to confirm an
adjustment or selection in the adjustment mode.
EXIT : to leave the adjustment mode or to scroll upwards
when in the adjustment mode.
Control disk : to make menu selections when in the
adjustment mode. Also allows to increment or decrement
an adjustment in the adjustment mode.
control disk up = up arrow in the menus
control disk down = down arrow in the menus
control disk to the right = arrow to the right on the menus
control disk to the left = arrow to the left on the menus
RC operating indication : lights up when a button on the
remote control is pressed. (This is a visual indicator to
check the operation of the remote control)
5975977 BARCODATA 708 260597
2-3
Page 14
Location and Function of Controls
2-4 5975977 BARCODATA 708 260597
Page 15
Connections
3
CONNECTIONS
Power (mains) cord connection
Use the supplied power cord to connect your projector to the
wall outlet. Plug the female power connector into the male
connector at the front of the projector.
Switching on/off
The projector is switched ON and OFF using the power
(mains) switch ON/OFF.
See installation instructions before
connectin g to the supply
OFF
V NOM 120/23 0 Volt
I MAX 5/2.5 AMP
FREQ 60/50 Hz
ON
Leds on the front plate of the projector
See installation instructions before
connecting to the supply
V NOM 120/230 Volt
I MAX 5/2.5 AMP
FREQ 60/50 Hz
ON
OFF
Pressed : ON
Not pressed : OFF
The projector can start now in the 'operational mode' (image
displayed) or in the 'stand by mode', depending on the
position of the 'power up' dip switch on the controller unit. This
DIP switch is set during installation by a qualified technician.
If you want to change this start up mode, call a qualified
technician.
Signal input connection to the projector :
- Composite Video (*)
- S-Video (*)
- RGBS or RGsB
- RGB3S or RG3sB
- (R-Y)Y(B-Y)S or (R-Y)Ys(B-Y) [component input] (**)
- (R-Y)Y(B-Y)3S or (R-Y)Y3s(B-Y) [component input] (**)
(*) If the line double feature is built in, this feature is available via a software on/off toggle.
(**) If the line double feature is built in, this feature is available for component video signals on standard
frequency via software on/off toggle.
RS232 IN
RS232 OUT
COMM PORT
(800 peripherals)
REMOTE
-CONV
RG(S)B
R-Y Y( S)
+17V
SF
+210V
S-VIDEO
+HTHD
+CONV
-17V
HOLD DOWN EHT
-9V
+9V
+30V
S
VIDEO
B-Y
STANDBY
HOLD DOWN HD
COINC
5975977 BARCODATA 708 260597
3
1 2
3-1
Page 16
Connections
Source No Projector input Press digit button
1 Comp. Video 1
2 S-Video*/Comp. Video
1
3 RGBS or RGsB** 3
3 RGB3S or RG3sB*** 4
3 (R-Y)Y(B-Y)S or
(R-Y)Ys(B-Y)**** 5
3 (R-Y)Y(B-Y)3S or
(R-Y)Y3s(B-Y)***** 6
Connecting a Composite Video source.
Composite video signals from a VCR, OFF air signal decoder,
etc..
If a line doubler is built in :
the default position of this line doubler is ON (active), the
video input signal will be displayed as a non interlaced image
(= improved image stability).
To enable or to disable this line doubler function, enter the
adjustment mode and change the position of the ON/OFF
toggle switch (see Picture tuning in chapter 'Guided' adjustment mode or 'Random access' adjustment mode).
2
* Input signal Y/C (luma/chroma)
** Input signal : R, G and B with composite sync on G or
separate composite sync
*** Input signal : R, G and B with Tri level sync on G or
separate Tri level sync.
**** Input signal : R-Y, Y and B-Y with composite sync on Y
or separate composite sync
***** Input signal : R-Y, Y and B-Y with Tri level sync on Y or
separate Tri level sync.
1
Video or S-Video : switchable in the Picture Tuning
menu.
COMM PORT
RG(S)B
REMOTE
(800 peripherals)
R-Y Y(S ) B-Y
RS232 OUTRS232 IN
S
VIDEO
Composite
video
S-VIDEO
Video input selection :
a. with the RCU : press digit button 1 or
b. with the local keypad.
(for access to the local keypad, see 'Local keypad' in chapter
'Location and function of controls'.)
- press
ADJUST key, the General access menu is displayed
on the screen.
- use the control disk to highlight 1.
ENTER to select the highlighted source.
- press
TV tuner, e.g. TVDM40 stereo
VCR
Audio amplifier
GENERAL ACCESS
5 6
3 4
1 2
Enter ADJUST
Select with ,
or
then <ENTER>.
<EXIT> to return
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
3-2 5975977 BARCODATA 708 260597
Page 17
Connecting a S-Video or Video source to port 2.
COMM PORT
(800 peripherals)
REMOTE
SVIDEO
S-VIDEO
VCR S-VHS
Audio amplifier
Luma/Chroma
RG(S)B
R-Y Y(S ) B-Y
RS232 OUT
RS232 IN
Separate Y-luma/C-chroma signals for higher quality playback of
Super VHS signals.
If a line doubler is built in :
the default position of this line doubler is ON (active), the video
input signal will be displayed as a non interlaced image (=
improved image stability).
To enable or to disable this line doubler function, enter the
adjustment mode and change the position of the ON/OFF
toggle switch (see Picture tuning in chapter 'Guided' adjustment mode or 'Random access' adjustment mode).
Input selection
a. with the RCU : press digit button 2 or
b. with the local keypad.
Connections
(for access to the local keypad, see Local keypad in chapter
Location and function of controls.)
- press
ADJUST key, the General access menu is displayed on the
screen.
- use the control disk to highlight 2.
- press
ENTER to select the highlighted source.
Depending on the priority setting in the 'Picture Tuning menu', Video
or S-Video can be displayed.
If the setting is not correct, start up the adjustment mode by pushing
on the
ADJUST key.
Select 'Random Access' and press ENTER.
Select 'Selected source' and press
Highlight 'Picture Tuning' and press
Highlight 'Port 2 : Video' and press
ENTER.
.
ENTER
ENTER to toggle between VIDEO
and S-VIDEO.
Press
Press
to return.
EXIT
ADJUST to return to operational mode.
5 6
3 4
1 2
Enter ADJUST
ADJUSTMENT MODE
Select a path from below :
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
Source 02
Choose a setup pattern
Select with or
from below :
then <ENTER>
<EXIT> to return.
SELECTED SOURCE
GENLOCKED PATTERN
INTERNAL # PATTERN
Select with or
then <ENTER>
<EXIT> to return.
GENERAL ACCESS
SHARPNESS
BRIGHTNESS
CONTRAST
Select with ,
or
then <ENTER>.
<EXIT> t o return
Source 02
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
SOFT EDGE
Select with or
then <ENTER>
<EXIT> to return.
TINT
COLOR
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PORT2 : S-VIDEO
LINE DOUBLER : ON
5975977 BARCODATA 708 260597
Select with or
<ENTER> to accept
<EXIT> to return.
3-3
Page 18
Connections
AAAA
A
A
A
A
AA
Connecting a RGB Analog source with composite sync.
RGB analog input terminals with composite sync input or with
sync on green. The projector detects automatically where the
sync signal is located.
Always use an interface when a computer and local monitor
have to be connected to the projector. Examples of interfaces
which can be applied :
Universal analog interface R9826100
RGB 120 MHz Analog Interface R9826570 (230V)
Multifunctional Analog Interface Kit R9828120 (230V)
(MAGIK) R9828129 (120V)
VGA interface R9828070 (230V)
R9828079 (120V)
MAC interface R9828050 (230V)
R9828059 (120V)
RGBS or RGsB input selection
a. Press digit button 3 on the RCU or
COMM PORT
RG(S)B
REMOTE
R-Y Y(S) B-YRS232 OUT
R
(800 peripherals)
ANALOG OUT
G
BS
RS232 IN
INPUT
SVIDEO
S-VIDEO
AAA
A
AAAA
AAA
A
AAAA
AAA
A
AAAA
AAA
AAAA
A
b. With the local keypad :
(to gain access to the local keypad, see 'Local keypad' in chapter
'Location and function of controls'.)
- Press
ADJUST key, the General access menu is displayed on
the screen.
- Use the control disk to highlight
3.
- Press ENTER to select the highlighted source.
Connecting a RGB Analog source with Tri-level sync.
RGB analog input terminals with Tri level sync input or with Trilevel sync on green. The projector detects automatically where
the sync signal is located.
RS232 IN
RS232 OUT
COMM PORT
(800 peripherals)
REMOTE
Enter ADJUST
RG(S)B
R-Y Y(S)
B-Y
GENERAL ACCESS
5 6
3 4
1 2
Select with ,
or
then <ENTER>.
<EXIT> to return
S-VIDEO
SVIDEO
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
VCR HDTV player
Audio amplifier
3-4 5975977 BARCODATA 708 260597
Page 19
RGB3S or RG3sB input selection
COMM PORT
(800 peripherals)
REMOTE
SVIDEO
S-VIDEO
Professional VCR
Audio amplifier
RG(S)B
R-Y Y(S ) B-Y
RS232 OUT
RS232 IN
GENERAL ACCESS
Select with ,
or
then <ENTER>.
<EXIT> to return
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
5 6
3 4
1 2
Enter ADJUST
COMM PORT
(800 peripherals)
REMOTE
SVIDEO
S-VIDEO
Professional VCR
with Tri-level sync
Audio amplifier
RG(S)B
R-Y Y(S)
B-Y
RS232 OUT
RS232 IN
a. Press digit button 4 on the RCU or
b. With the local keypad :
Connections
(to gain access to the local keypad, see 'Local keypad' in chapter
'Location and function of controls'.)
- Press
ADJUST key, the General access menu is displayed on
the screen.
- Use the control disk to highlight
4.
- Press ENTER to select the highlighted source.
Connecting a Component source.
(R-Y)Y(B-Y) analog input terminals with sync input or with sync on the
luminance (Y) input. The projector detects automatically where the
sync signal is located.
Line doubling is possible for component video input sources on
standard line frequency.
If a line doubler is built in :
the default position of this line doubler is ON (active), the
component video input signal will be displayed as a non
interlaced image (= improved image stability).
To enable or to disable this line doubler function, enter the
adjustment mode and change the position of the ON/OFF
toggle switch (see Picture tuning in chapter 'Guided' adjustment mode or 'Random access' adjustment mode).
GENERAL ACCESS
5 6
3 4
1 2
Enter ADJUST
Select with ,
or
then <ENTER>.
<EXIT> t o return
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
(R-Y)Y(B-Y)S or(R-Y)Ys(B-Y) input selection
a. Press digit button 5 on the RCU or
b. With the local keypad :
(to gain access to the local keypad, see 'Local keypad' in chapter
'Location and function of controls'.)
- Press
ADJUST key, the General access menu is displayed on
the screen.
- Use the control disk to highlight
5.
- Press ENTER to select the highlighted source.
Connecting a Component source with Tri-level sync.
(R-Y)Y(B-Y) analog input terminals with Tri-level sync input or with
Tri-level sync on the luminance input.
5975977 BARCODATA 708 260597
3-5
Page 20
Connections
A
A
A
A
AAAA
AAAA
A
A
A
A
A
(R-Y)Y(B-Y)3S or (R-Y)Y3s(B-Y) input selection
a. Press digit button 6 on the RCU or
b. With the local keypad :
(to gain access to the local keypad, see 'Local keypad' in chapter
'Location and function of controls'.)
- Press
ADJUST key, the General access menu is displayed on
the screen.
- Use the control disk to highlight
6.
- Press ENTER to select the highlighted source.
GENERAL ACCESS
5 6
3 4
1 2
Enter ADJUST
Select with ,
or
then <ENTER>.
<EXIT> to return
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
Connecting a computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS232 input of the projector.
The projector has a RS232 port that allows it to communicate with a
computer.
Applications: remote control and data communications.
a) remote control:
- easy adjustment of the projector via IBM PC (or compatible) or
MAC connection.
- allow storage of multiple projector configurations and set ups.
- wide range of control possibilities.
- address range from 0 to 255.
b) data communications:
- sending data to the projector or copying the data from the projector
to a hard memory device.
Peripheral equipment
Connecting a RCVDS 05 switcher to the projector.
- Up to 10 inputs (20 inputs when video and S-video) with the RCVDS
05 switcher and up to 90 inputs when 10 RCVDS switchers are
linked via the expansion modules.
- Serial communication with the projector.
- Remote control buttons on the RCVDS to control the projector
(source selection and analog settings)
- The selected source number will be displayed on a 2 digit display and
the selected input modules will be indicated with a LED on the rear.
For more information about the use of the RCVDS 05, consult the
Owner's Manual, order number: R5975765.
COMM PORT
(800 peripher al s)
RS232 OUTRS232 IN
RS232
connection
REMOTE
RG(S)B
R-Y Y(S)
S-VIDEO
SVIDEO
B-Y
AAA
AAAA
AAA
AAAA
AAA
AAAA
AAA
AAAA
Connecting an IR Remote Receiver to the
projector
This infra-red receiver unit makes it possible to control the projector
from another room. There is a communication line cable between the
IR receiver and the projector or the RCVDS. The infrared control
information from the Remote Control Unit is sent to the IR Remote
Receiver. The IR Remote Receiver 800 displays the selected source
on a 7-segment display.
Order number : R9827515.
Connecting a VS05 switcher to the projector.
The VS05 can switch up to 5 Composite Video sources, 3 S-Video
Sources and 1 RGB analog or component Video source to the
projector. In addition, the audio signal proper to the source, can be
switched to an audio amplifier.
Order number : R9827890.
For more information about the use of the VS05, consult the Owner's
Manual, order number: R5975245.
3-6 5975977 BARCODATA 708 260597
Page 21
Controlling
4
CONTROLLING
Caution : Do not display a stationary image with full brightness
and contrast for longer than 20 min., otherwise you risk damage
to the CRT's.
Battery installation in the RCU.
A new battery is delivered inside the plastic bag with the power cord. Before using the RCU, install
first the battery.
Remove the battery cover on the backside of the remote control by pushing the indicated handle a
little to the bottom of the RCU. Lift up the top side of the cover at the same time (fig. 1).
Insert the new 9 V battery (E-block type, e.g. 6F22S or equivalent) in the lower compartment and
connect the battery to the contact plate.
Insert the battery into the lower compartment and put the cover back.
Contact
plate
Battery
310a.DRW
Insert here,
behind the
plastic cover, the
'Insert card for
RCU'. You can
cut out this card
on one of the
last pages of this
manual.
fig.2
fig.1
5975977 BARCODATA 708 260597
4-1
Page 22
Controlling
The projector can be controlled with
a. The RCU
b. The hardwired RCU (cable not included)
c. The local keypad.
Controlling the projector with the RCU and the hardwired RCU is
the same.
How to use the RCU
a) Point the front of the RCU towards the reflective screen surface
Ceiling
IR sensor
Screen
RCU700
c) RCU used in a hardwired configuration.
COMM PORT
RS232OUTRS232IN IR
REMOTE R G(S) BSVIDEO
(800 peripherals)
S-VIDEO
219
Plug one end of the remote cable in the connector on the bottom of
the RCU and the second side in the connector in the rear panel of the
projector labelled '
REMOTE
'.
Projector address
a. Software set up of the projector address.
See 'Change Projector Address' in chapter 'Service mode'.
Every projector requires an individual address between 0 and 255
which is set in the Service mode. Only projectors with addresses
between 0 and 9 can be controlled with the RCU.
b) Point the front of the RCU towards one of the IR sensors in the
projector.
When using the wireless remote control, make sure you are within the
effective operating distance (30m, 100ft in a straight line). The
remote control unit will not function properly if strong light strikes the
sensor window or if there are obstacles between the remote control
unit and the projector's IR sensor.
Front of projector
45°
45°
Rear side of projector
45°
45°
b. How to control the projector.
The projector's address may be set to any value between 0 and 255.
When the address is set, the projector can be controlled with :
- the RCU for addresses between 0 and 9.
- Computer, e.g. IBM PC (or compatible), Apple MAC, etc. for
addresses between 0 and 255.
Note : A projector will respond to an RCU set to an address of '0'
regardless of what address is set in the projector itself.
c. Using the RCU.
Before using the RCU, it is necessary to enter the projector address
into the RCU (only when that address is between 1 and 9). The
projector with the corresponding address will listen to that specific
RCU.
When address 0, 'zero address' is programmed into the RCU, every
projector, without exception will listen to the commands given by this
RCU.
How to display a projector address?
Press the ADDRESS key (recessed key on the RCU) with a pencil.
The projector's address will be displayed in a 'Text box'. This text box
disappears after a few seconds.
ENTER
FREEZ
0
9
7
8
6
5
4
3
21
RCU
ENTER
FREEZ
0
9
7
8
6
5
43
21
PROJECTOR
ADDRESS
001
4-2 5975977 BARCODATA 708 260597
Page 23
Controlling
To continue using the RCU, it is necessary to enter an address with
the digit buttons (address between 0 and 9). For example : if the
Address key displays projector address 003, the press "3" digit
button on the RCU to set the RCU's address to match the projector's
address. Do not press digit 003. This will address the remote to '0'
and control all projectors in the room.
How to program an address into the RCU?
Press the ADDRESS key (recessed key on the RCU) with a pencil
and enter the address with the digit buttons. That address can be any
digit between 0 and 9.
Input selection
Source No Projector input Press button
1 Comp. Video 1
2 S-Video/Comp. Video
1
2
3 RGBS or RGsB 3
3 RGB3S or RG3sB 4
3 (R-Y)Y(B-Y)S or
(R-Y)Ys(B-Y) 5
control disk to the left or to the right to move the cursor to the left and
to the right.
ENTER to confirm your selection.
Press
When a valid and available source is selected, there will be informa-
tion displayed on the screen about that source. This information
includes :
- Source number
- Horizontal frequency
- Vertical frequency
Source 2
Fh= 15.6 kHz
Fv= 50 Hz
When the entry is a non valid source number, a warning appears on
the screen : '
input not available
'.
3 (R-Y)Y(B-Y)3S or
(R-Y)Y3s(B-Y) 6
Two possible ways of selecting an input :
a) With the digit buttons on the RCU, it is possible to select one of the
four input sources, Video, S-Video, RGsB or RGBS, RG3sB or
RGB3S, (R-Y)Ys(B-Y) or (R-Y)Y(B-Y)S, (R-Y)Y3s(B-Y) or (R-Y)Y(BY)3S.
b) With the local keypad :
press first the
Use the control disk to highlight the desired source number. Push the
control disk up or down to move the cursor up and down, push the
ADJUST key to display the
General access
ADJUST
STANDBY
menu.
EXIT
ENTER
WARNING
input not
available
When a valid source number is selected, the projector will display this
source or it will wait on the selected source number until the source
becomes available. A message 'source not available' will be displayed for a short time.
WARNING
source not
available
Enter ADJUST
5975977 BARCODATA 708 260597
GENERAL ACCESS
5 6
3 4
1 2
Select with ,
or
then <ENTER>.
<EXIT> to return
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
4-3
Page 24
Controlling
Picture controls
The picture controls can be adjusted with :
a) The RCU. The control keys are located on the left side of the key
panel of the RCU and indicated with the name of the control and
an icon.
When an image control is pressed, a text box with bar scale and the
function name of the control, e.g. 'brightness...' appears on the
screen (only if text is ON). The length of the bar scale indicates the
current memorized setting for this source. The bar scale changes
as the + or - buttons of the control are pressed.
b) The local keypad
All controls are hidden in the General access menu.
- Press
ADJUST to display the
- Use the control disk to highlight the desired analog control and
press
ENTER to select.
General access
ADJUST
STANDBY
menu.
EXIT
ENTER
A bar scale gives a visual indication on the screen of the current
brightness setting while pressing on the above indicated buttons. If
the bar scale is not visible on the screen, press '
TEXT' once and retry
the above indicated buttons.
The bar scale increases when pressing on the + button (higher
brightness) and decreases when pressing on the - button (lower
brightness).
Contrast Control
A correct 'contrast' setting is important for good image reproduction.
Adjust the contrast to the level you prefer, according to room lighting
conditions.
A bar scale gives a visual indication on the screen of the current
contrast setting while pressing the + or - buttons (RCU) or pushing the
control disk to the left or to the right (local keypad). If the bar scale is
not visible on the screen, press '
TEXT' key once and retry the above
indicated buttons.
The bar scale increases when pressing on the + button (higher
contrast) and decreases when pressing on the - button (lower
contrast).
Color Saturation Control
Color saturation is only active for Video and S-Video. Adjust the color
intensity of the picture. Adjust the color saturation using the + and buttons (RCU) or pushing the control disk to the left or to the right
(local keypad). A bar scale gives a visual indication on the screen of
the current color setting while pressing on the above indicated
buttons. If the bar scale is not visible on the screen, press '
TEXT' key
once and retry the above indicated buttons. The bar scale increases
when pressing on the + button (richer colors) and decreases when
pressing the - button (lighter colors).
GENERAL ACCESS
SHARPNESS
TINT
5 6
3 4
1 2
Enter ADJUST
Select with ,
or
then <ENTER>.
<EXIT> t o return
COLOR
BRIGHTNESS
CONTRAST
When a picture control is selected, a text box with bar scale and the
function name of the control (e.g. brightness) appear on the screen.
The length of the bar scale indicates the current memorized setting
for this source (percentage scale). The bar scale changes as the
control disk is pushed to the left or to the right.
BRIGHTNESS
35
Tint Control
Tint is only active for Video and S-Video. Tint control is effective only
when using the NTSC 4.43 or NTSC 3.58 system. A bar scale gives
a visual indication on the screen of the current tint setting while
pressing the + or - buttons (RCU) or pushing the control disk to the
left or to the right (local keypad). If the bar scale is not visible on the
screen, press the '
TEXT' key once and retry the above indicated
buttons.
The bar scale increases when pressing on the + button and decreases when pressing the - button.
Sharpness Control.
Sharpness control only active for Video and S-Video. A bar scale
gives a visual indication on the screen of the current sharpness
setting while pressing the + or - buttons (RCU) or pushing the control
disk to the left or to the right (local keypad). If the bar scale is not
visible on the screen, press '
TEXT' key once and retry the above
indicated buttons.
The bar scale increases when pressing on the + button (sharper
picture) and decreases when pressing on the - button (softer picture).
The Pause key.
When the Pause key is pressed, the image projection is stopped but
the projector remains with full power for immediate restart.
To restart the image :
- Press the Pause key,
- Select a source number.
189
Brightness Control
A correct
'brightness'
setting is important for good image reproduction. Adjust the brightness with the + button and - button (RCU) or
pushing the control disk to the left or to the right (local keypad) until
the darkest parts of the picture appear black.
4-4 5975977 BARCODATA 708 260597
Page 25
Safety Instructions
ADJUST
STANDBY
ENTER
EXIT
5
START UP OF THE ADJUSTMENT MODE
Adjustment mode
All picture geometry and convergence adjustments are made while in the 'Adjustment mode'. Two possible ways to enter the adjustment
mode :
a) Using the RCU.
Press the
The projector displays the path selection menu.
b) Using the local keypad.
Press the
The projector displays the
ADJUST key.
ADJUST key.
General access menu
.
Use the control disk to highlight
enter ADJUST
and press ENTER. The path
selection menu will be displayed.
Note : to adjust the Analog picture control while in the 'Adjustment mode', press
the ADJUST key. The next General Access menu will be displayed.
Push the control disk up or down to select the analog control to be adjusted and
press the
ENTER key to confirm.
When the analog control is adjusted the projector returns automatically to the
General access menu. When you want to return to the Adjustment mode, press
EXIT, otherwise select
quit ADJUST
and press ENTER to return to operational
mode.
You are now in the
'Adjustment mode'
. The control disk is used to make menu
selections and also vertical and horizontal adjustments. The ENTER and EXIT
keys are used to move forward and backward through the menu structure. The
ADJUST key can be used to terminate the adjustment mode while a path
selection menu (head menu) is displayed.
There are 5 possible paths to follow once in the Adjustment mode. They are :
INSTALLATION - Installation should be selected if the projector has been
relocated and/or a different screen size is desired.
When selecting 'Installation', the user or operator will be warned to call a qualified
technician to perform the installation procedure (see example of projected
warning on next page).
GUIDED - Guided should be selected if the user intends to perform a complete
alignment of the projected image. All of the necessary geometry and convergence adjustments are made in a predetermined sequence.
GENERAL ACCESS
5 6
3 4
1 2
Enter ADJUST
Select with ,
or
then <ENTER>.
<EXIT> t o return
GENERAL ACCESS
Select with ,
or
then <ENTER>.
<EXIT> to return
ADJUSTMENT MODE
Select a path from
below:
GUIDED
RANDOM ACCESS
INSTALLA T IO N
SERVICE
IRIS
Select with or
then <ENTER>
<EXIT> to ret urn
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
quit ADJUST
source 1
643
5975977 BARCODATA 708 260597
5-1
Page 26
Safety Instructions
RANDOM ACCESS - Random Access should be selected if the user intends to make
only a few adjustments.
SERVICE - Service should be selected if the user intends to delete blocks, change
password or apply information.
IRIS - This selection will only be available when the autoconvergence unit IRIS is
connected to the projector.
While in Guided or Random Access adjustment Mode, the user may use an external
source, an internally generated genlocked pattern or an internally generated
multifrequency cross hatch pattern as a setup pattern.
Warning during the start up of the installation mode.
Some items in the Adjustment mode are password protected. While selecting such
an item, the projector asks you to enter your password. (Password protection is only
available when the password DIP switch on the controller module is in the ON
position. Contact a BARCO authorized technician when no password is requested
during the adjustment procedure and password protection is desired.)
Your password contains 4 digits.
a) Adjusting the projector with the RCU.
Enter the digits with the numeric keys on the RCU.
Example : 2 3 1 9
For each digit entered, a 'X' appears on the screen under the displayed text 'enter
password'.
When your password is correct, you get access to the 'Adjustment mode'.
When the entered password is wrong, The message
'Wrong password !!!'
will be
displayed. The projector stays on the previous selected item.
WARNING
RISK OF ELECTRICAL SHOCK
NO USER ADJUSTABLE PARTS
INSIDE
THE FOLLOWING
INSTALLATION MENUS
ARE RESERVED TO,
AND TO BE PERFORMED ONLY
BY BARCO PERSONNEL, OR
BARCO AUTHORIZED DEALERS
IF QUALIFIED, PRES S
<ENTER> TO CONTINUE, OR
IF NOT, <EXIT> TO RETURN.
enter
password
xxxx
197
Factory programmed
password :
0000
WRONG
PASSWORD
!!!
198
b) adjusting the projector with the local keypad.
When the 'compose password' menu is displayed, select with control disk the first
digit of your password and press
with the control disk and press
fourth digit.
When your password is correct, you get access to the 'Adjustment mode'.
When the entered password is wrong, the message 'Wrong password' will be
displayed.
Once the password is correctly entered, all other password protected items are
accessible without re-entering your password.
ENTER. Continue by selecting the second digit
. Handle in the same way for the third and
ENTER
COMPOSE
PASSWORD
???
7 8 9
4 5 6
1 2 3
0
Select with ,
or
then <ENTER>
<EXIT> to return
When re-entering the adjustment mode, it will be necessary to enter your password
again when selecting a password protected item.
5-2 5975977 BARCODATA 708 260597
Page 27
Random Access Adjustment Mode
6
RANDOM ACCESS ADJUSTMENT MODE
Starting up the random access adjustment mode.
Push the control disk up or down to highlight
CESS"
and then press ENTER.
Some items in the Random access mode are password protected
(when the password function is enabled). Enter your password
to continue. All other password protected items are now also
available if you stay in the adjustment mode.
ENTER continues to Setup Pattern Selection
EXIT returns to operational mode
Overview 'random Access Adjustment' mode.
PICTURE TUNING
"RANDOM AC-
COLOR BALANCE
SYNC
LINE DOUBLER
ADJUSTMENT MODE
Select a path from
below:
GUIDED
RANDOM ACCESS
INSTALLA T IO N
SERVICE
IRIS
source 1
Select with or
then <ENTER>
<EXIT> to ret urn
RANDOM ACCESS
ADJUSTMENT MODE
SETUP PATTERN SELECTION
GEOMETRY
PORT 2
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
TOP-BOTTOM (N-S)
SIZE
VER LINEARITY
V CENTERLINE BOW
V CENTERLINE SKEW
SIDE BOW
SIDE KEYSTONE
SEAGULL CORRECTION
H CENTERLINE BOW
H CENTERLINE SKEW
TOP KEYSTONE
TOP BOW
BOTTOM KEYSTONE
BOTTOM BOW
SEAGULL CORRECTION
TOP BOW
5975977 BARCODATA 708 260597
BLANKING
BOTTOM KEYSTONE
BOTTOM BOW
CONVERGENCE
SEAGULL CORRECTION
COLOR SELECT
6-1
Page 28
Random Access Adjustment Mode
Selecting Setup Pattern
If an external source is connected to the projector, this menu will be displayed. Push the
control disk up or down to highlight the desired setup pattern and then press ENTER.
Genlocked pattern : internally generated cross hatch pattern, locked on the external source.
Internal # pattern : internally generated cross hatch pattern and locked on internal generated
sync signals. (No external source necessary)
ENTER continues to Random Access Adjustment Mode or Internal # Pattern
Selection
EXIT returns to Path Selection menu
ADJUST returns to Operational mode
If no external source is connected to the projector, the internal cross hatch pattern menu will
be displayed.
Note: The menus in this manual are created for an external source, connected to one of the
inputs, and the 'Genlocked Pattern' is selected.
Internal Cross Hatch Pattern
Choose a setup pattern
from below :
SELECTED SOURCE
GENLOCKED PATTERN
INTERNAL # PATTERN
Select with or
then <ENTER>
<EXIT> to return.
Source 01
The Internal # pattern menu will be displayed if the internal cross hatch pattern has been
selected or if no source is connected to the projector.
The table below lists the 8 fixed factory preset frequencies available. Another 8 blocks are
custom programmable.
Push the control disk up or down to highlight the desired cross hatch frequency. Push the
control disk tp the left or to the right to scroll to another page. Press
ENTER if the desired block
is selected.
kHz/Hz
15.6/50 PAL/SECAM
15.7/60 NTSC
31.2/50 EDTV
31.5/60 IDTV
31.2/50 HDTV EUREKA
31.5/60 HDTV ATV
33.7/60 HDTV HIVISION
15.8/60 EGA 1
21.8/60 EGA 2
31.5/60 VGA 3
31.5/70 XGA 1, 2
35.5/87 VGA 4
44.2/70 SUPER VGA 2
48.5/60 SUPER VGA 1
61.0/76 SUPER VGA 3
63.9/76 APOLLO
INTERNAL # PATTERN
kHz / Hz
15.6/50 PAL/SECAM
15.7/60 NTSC
31.2/50 EDTV
31.5/60 IDTV
31.2/50 HDTV EUREKA
31.5/60 HDTV ATV
Select with or
scroll with or
<ENTER> to accept
<EXIT> to return
ENTER
continues to the Random Access Adjustment Mode.
EXIT returns to the Setup Pattern Selection menu.
6-2 5975977 BARCODATA 708 260597
Page 29
Random access adjustment mode selection menu.
Random Access Adjustment Mode
This is the main menu for the Random Access adjustment mode.
Through this menu, the following adjustments and features are accessible :
- Picture Tuning
Enhanced Blue (only for RGB)
Sync slow/fast(video/s-video)
Color Balance
- Geometry
- Convergence
- Color select
And also Orbiting, Contrast modulation and Soft Edge if these options are installed.
Picture Tuning
Highlight
The Picture tuning menu will be displayed.
Depending on the input source, the 'Picture tuning' menu will display different items.
- Color Balance
- Sync slow/fast
- Line doubler
- Port 2 : S-Video
- Peaking
Picture tuning
by pushing the control disk up or down and press ENTER.
Color Balance
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
COLOR SELECT
Select with or
then <ENTER>
<EXIT> to return.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PORT 2 : S-VIDEO
PEAKING : ON
LINE DOUBLER : ON
Select with or
<ENTER> to accept
<EXIT> to return.
The Color Balance function is used to select or adjust the color
temperature of white used by the projector.
The Color Balance can be adjusted on two different ways :
- fixed color balance. You have the choice between 3200 K (reddish),
4900 K, 6500 K (white) or 9300 K (bluish).
- Custom white and black balance.
Fixed Color Balance.
Highlight
one of the 4 preprogrammed color temperatures
with the
control disk and press ENTER to display the desired color balance.
Custom Color Balance.
Select custom white balance by pushing the control disk up or down
and press ENTER to start the adjustment.
Push the control disk up or down to adjust the red gain and push the
control disk to the left or to the right to adjust the blue gain. A bar scale
indicates the amount of adjustment.
Select custom black balance with the control disk and press
ENTER
to start the adjustment.
Push the control disk up or down to adjust the red cut-off and push the
control disk to the left or to the right to adjust the blue cut-off.
When the color balance is adjusted, select continue by pushing the
control disk up or down and press
ENTER.
Sync Fast/Slow Adjustment
The sync function is used to minimize horizontal jittering or tearing at
the top to the displayed image.
Highlight
between
Note: SYNC is normally used in the SLOW position. The FAST
position is used to compensate for unsteady sync pulses from older
video playback equipment.
Hint : when the line doubler feature is ON (active), toggle the sync to
FAST.
SYNC
with the control disk and press ENTER to toggle
FAST
and
SLOW
.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING : ON
LINE DOUBLER : ON
Select with or
<ENTER> to accept
<EXIT> to return.
FIXED COLOR BALANCE
CUSTOM WHITE BALANCE
CUSTOM BLACK BALANCE
COLOR BALANCE
3200 4900 6500 9300
Select with arrow keys
then <ENTER>
You can
adjust red with or
Blue with or
<EXIT> to return
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
LINE DOUBLER : ON
Select with or
<ENTER> to accept
<EXIT> to return.
ENTER will toggle Sync between FAST and SLOW
EXIT will return to the Randam Access Adjustment menu.
5975977 BARCODATA 708 260597
6-3
Page 30
Random Access Adjustment Mode
Line Doubler (option)
Line doubling is only possible for Video, S-Video, Component
Video images on standard line frequency and RGB signals on 15
kHz.
To eliminate the video line patterns and to improve the image
stability, the line doubler has to be switched on. The line doubler
is default set in the ON position when starting up for the first time.
The setting of the line doubler will be saved together with the
source number. Each time this source number is selected, the
last saved version will be loaded.
Highlight Line Doubler with the control disk and press
ENTER to
toggle between ON (active) and OFF (non active).
EXIT will return to the random access selection menu.
Port 2 : S-Video/Video
Port 2 can be used as Video or S-Video input.
Highlight
ENTER to toggle between
Port 2
by pushing the control disk up or down and press
Video
and
S-Video
.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING : ON
LINE DOUBLER : ON
Select with or
<ENTER> to accept
<EXIT> to return.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING :ON
LINE DOUBLER : ON
PORT 2 : S-VIDEO
Peaking
Peaking improves the contours in an projected image.
Highlight
PEAKING
by pushing the control disk up or down and press
ENTER to toggle the peaking between OFF and ON.
During the creation of new settings for a RGB source the peaking is
switched to OFF.
Color Select
Highlight
and press
Use the control disk to highlight a color (CRT) or combination of
colors to display the projected image in that specific color.
To select a new color, press
appears again on the screen. To terminate the color select procedure, press EXIT.
COLOR SELECT
by pushing the control disk up or down
ENTER to display the color select menu.
ENTER continues to the color select menu.
EXIT will return to Internal Crosshatch Selection or Setup
Pattern Selection Menu.
ADJUST returns to operational mode.
ENTER, the color selection menu
ENTER continues with the selected color or color combina-
tion.
EXIT returns to the Random access main menu.
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
COLOR SELECT
Select with or
<ENTER> to accept
<EXIT> to return.
Select with or
<ENTER> to accept
<EXIT> to return.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING : OFF
LINE DOUBLER : ON
Select with or
<ENTER> to accept
<EXIT> to return.
COLOR SELECT
RED
GREEN
BLUE
RED AND GREEN
BLUE AND GREEN
RED AND BLUE
Select with or
<ENTER> to accept
<EXIT> to return.
6-4 5975977 BARCODATA 708 260597
Page 31
Random Access Adjustment Mode
H PHASE
><
70
Geometry Adjustments
The geometry adjustments have to be done only on the green image. These adjustments are automatically implemented for the other color
images : Left-right (EW) and Top-Bottom Corrections, Blanking, Horizontal Amplitude, Vertical Amplitude, Vertical Linearity and Horizontal
Phase.
Highlight
GEOMETRY
by pushing the control disk up or down and
press ENTER to display the geometry menu.
ENTER will display Geometry menu.
EXIT will return to Internal Crosshatch Selection or Setup
Pattern Selection Menu.
ADJUST returns to operational mode.
Within the Geometry Adjustment menu, the following adjustments
are available :
- Horizontal Phase (not for internal # pattern).
- Raster Shift
- Left-Right Corrections
- Top-Bottom Corrections
- Horizontal Size
- Vertical Linearity
- Vertical Size
- Blanking
The convergence corrections are disabled during geometry corrections. The blanking corrections are only enabled during the blanking
adjustments.
Horizontal Phase Adjustment
Push the control disk up or down to highlight
menu
and then press ENTER.
H PHASE
on
Geometry
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
COLOR SELECT
Select with or
then <ENTER>
<EXIT> to return.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
TOP-BOTTOM (N-S)
SIZE
V LINEARITY
BLANKING
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
TOP-BOTTOM (N-S)
SIZE
V LINEARITY
BLANKING
Select with or
then <ENTER>
<EXIT> to return.
Note : No horizontal phase adjustment is available on the internal #
pattern.
For external sources :
If the raster shift is correctly adjusted, the H Phase text box is
projected in the middle of the raster. At that moment, the "><" icon
indicates the middle of the raster.
Adjust the H Phase control until the middle of the projected image is
equal with the middle of >< icon.
Note :
- If the genlocked pattern was selected, the external source will be
displayed.
A bar scale and a number indicator (between 0 and 100) on the
screen give a visual indication of the horizontal phase adjustment.
ENTER continues to geometry menu .
Push the control disk to
the right to correct
Push the control disk to
the left to correct
Select with or
then <ENTER>
<EXIT> to return.
><
H PHASE
70
5975977 BARCODATA 708 260597
><
H PHASE
70
6-5
Page 32
Random Access Adjustment Mode
Raster Shift Adjustment
The green raster must be centered both horizontally and vertically on
the center of the CRT surface. To center the green raster, look into
the green lens and use the control disk to move the raster.
CAUTION
It is necessary to look into the lenses to perform these adjustments.
To avoid eye discomfort while looking into the lenses, reduce the
contrast and gradually increase the brightness level until the raster
becomes visible on the face of the CRT.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
TOP-BOTTOM (N-S)
SIZE
V LINEARITY
BLANKING
Select with or
then <ENTER>
<EXIT> to return.
COARSE SHIFT
ENTER will select green raster shift adjustment
EXIT returns to random access adjustment mode menu.
Warning
: In order to ensure maximum CRT longevity and to
avoid CRT damage, do not shift the raster outside the
phosphor area of the CRT.
To start the adjustment, use the control disk to highlight Raster shift
and press ENTER to display the green raster on the phosphor.
forbidden area
GREEN HORIZONTAL
GREEN VERTICAL
RED VERTICAL
BLUE VERTICAL
Select with or
then <ENTER>
<EXIT> to return.
projected raster
crt faceplate border
phosphor border
correct raster position
wrong raster positions
Press EXIT to return to the Geometry menu.
Note : Horizontal and Vertical shifts for Red and Blue should
end up with a setting close to 50%. If these settings are
significantly greater or lesser than 50%, contact a BARCO
authorized service technician.
233
6-6 5975977 BARCODATA 708 260597
Page 33
Left-Right (east-west) Adjustments
Left-right and center adjustments affect only the vertical lines of the
projected image.
Random Access Adjustment Mode
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
TOP-BOTTOM (N-S)
SIZE
V LINEARITY
BLANKING
To start up the left-right and center adjustments, follow the next
procedure :
Push the control disk up or down to highlight
LEFT-RIGHT (E/W)
on
the geometry menu and then press ENTER.
ENTER will select Left-Right adjustment menu
EXIT returns to random access adjustment mode main menu.
ADJUST returns to operational mode
Only the green image is displayed while making left-right adjustments. The red and blue images will automatically be corrected in the
same manner. Convergence corrections are automatically disabled
for the duration of these adjustments.
The following adjustments can be executed
- vertical centerline bow
- vertical centerline skew
- side keystone (left - right)
- side bow (left - right)
All adjustment are indicated on the screen with the function name, a
bar scale and a number between 0 and 100.
Adjust the next alignments until the vertical lines are straight.
To enter an alignment, push the control disk up or down to highlight
a function and press
Press
EXIT to return.
ENTER to activate this function.
Select with or
then <ENTER>
<EXIT> to return.
Corrects for curvature of the vertical lines in the middle
of the image.
Corrects the tilting of the vertical lines in the middle of
the image.
LEFT-RIGHT (E-W)
V CENTERLINE BOW
V CENTERLINE SKEW
RIGHT BOW
RIGHT KEYSTONE
LEFT BOW
LEFT KEYSTONE
Select with or
then <ENTER>
<EXIT> to return.
LEFT-RIGHT (E-W)
V CENTERLINE BOW
V CENTERLINE SKEW
RIGHT BOW
RIGHT KEYSTONE
LEFT BOW
LEFT KEYSTONE
Select with or
then <ENTER>
<EXIT> to return.
Corrects for curvature of the vertical lines on the right side
Corrects the keystone geometry correction of the vert. lines on
the right side
Corrects for curvature of the vertical lines on the left side
Corrects the keystone geometry correction of the vert. lines on
the left side
Correct by pushing
the control disk to the
right
Correct by pushing
the control disk to
the left
5975977 BARCODATA 708 260597
6-7
Page 34
Random Access Adjustment Mode
Top-Bottom (north-south) Adjustments
Top-Bottom and center adjustments affect only the horizontal lines of
the projected image.
To start up the Top-Bottom and center corrections, follow the next
procedure :
Push the control disk up or down to highlight
the geometry menu and then press
TOP-BOTTOM (N/S)
ENTER.
on
Only the green image is displayed while making top-botton adjustments. The red and blue images will automatically be corrected in the
same manner. Convergence corrections are automatically disabled
for the duration of these adjustments.
The following adjustments can be executed :
- Horizontal centerline bow
- Horizontal centerline skew
- Top bow
- Top keystone
- Bottom bow
- Bottom keystone
All adjustment are indicated on the screen with the function name, a
bar scale and a number between 0 and 100.
Adjust the next alignments until the vertical lines are straight.
To enter an alignment, push the control disk up or down to highlight
a function and press
Press
EXIT to return.
ENTER to activate this function.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
TOP-BOTTOM (N-S)
SIZE
V LINEARITY
BLANKING
Select with or
then <ENTER>
<EXIT> to return.
Corrects for curvature of the horizontal lines in the
middle of the image.
TOP-BOTTOM (N-S)
H CENTERLINE BOW
H CENTERLINE SKEW
TOP KEYSTONE
TOP BOW
BOTTOM KEYSTONE
BOTTOM BOW
Select with or
then <ENTER>
<EXIT> to return.
TOP-BOTTOM
H CENTERLINE BOW
H CENTERLINE SKEW
TOP BOW
TOP KEYSTONE
BOTTOM BOW
BOTTOM KEYSTONE
Select with or
then <ENTER>
<EXIT> to return.
Corrects the tilting of the horizontal lines in the middle
of the image.
Corrects for curvature of the horizontal lines on the upper
side
Corrects the keystone geometry correction of the hor. lines
on the upper side
Corrects for curvature of the horizontal lines on the lower
side
Corrects the keystone geometry correction of the hor. lines
on the lower side
Correct by pushing
the control stick
backward
Correct by pushing
the control stick
forward
6-8 5975977 BARCODATA 708 260597
Page 35
Size Adjustment
Random Access Adjustment Mode
Push the control disk up or down to highlight
SIZE
on the Geometry
menu and then press ENTER.
ENTER will select size adjustment.
EXIT returns to random access adjustment mode menu.
ADJUST returns to operational mode.
Adjust the horizontal size by pushing the control disk to the right or to
the left until the exact image width is obtained.
Adjust the vertical size by pushing the control disk up or down until the
exact image height is obtained.
Note :
- If the internal # pattern was selected, this pattern remains on the
screen.
- If the genlocked pattern was selected, the external source will be
displayed.
A bar scale and a numeric indicator help to gauge the size adjustment.
Hint : In order to avoid loss of resolution in the projected image and
to ensure maximum CRT longevity, do not use an excessively small
horizontal size setting.
EXIT will return to Geometry.
H size too
large
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
TOP-BOTTOM (N-S)
SIZE
V LINEARITY
BLANKING
Select with or
then <ENTER>
<EXIT> to return.
H SIZE
70
Ideal
Image
Hight
Image too
Tall
Ideal
Image
Hight
Image too
Short
Vertical Linearity Adjustment
The vertical linearity adjustment function corrects for vertical nonlinearities which extend from the center of the image to the top and
bottom of the image.
Push the control disk up or down to highlight
Geometry menu and then press ENTER.
ENTER will select vertical linearity adjustment.
EXIT returns to random access adjustment mode menu.
ADJUST returns to operational mode.
Adjust the vertical linearity with the control disk until the distances
between the horizontal lines of the set up pattern are equal from top
to bottom.
EXIT will return to the Geometry menu.
V LINEARITY
on the
H size too
small
Ideal image width
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Select with or
then <ENTER>
<EXIT> to return.
V LINEARITY
70
5975977 BARCODATA 708 260597
6-9
Page 36
Random Access Adjustment Mode
Blanking Adjustments
Blanking adjustments affect only the edges of the projected image
and are used to frame the projected image on to the screen and to hide
or black out unwanted information (or noise). A 0% on the bar scale
indicates no blanking.
To start up the Blanking adjustments, follow the next procedure :
Push the control disk up or down to highlight
Geometry menu and then press ENTER.
The following blanking corrections are possible :
- Top blanking
- Bottom blanking
- Left blanking
- Right blanking
Therefore :
- If the internal # pattern was selected, this pattern remains on the
screen.
- If the genlocked pattern was selected, the external source
will be displayed.
BLANKING
on the
Left blanking
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
TOP-BOTTOM (N-S)
SIZE
V LINEARITY
BLANKING
Select with or
then <ENTER>
<EXIT> to return.
Top blanking
BLANKING
TOP
BOTTOM
LEFT
RIGHT
Select with or
then <ENTER>
<EXIT> to return.
Right blanking
Adjust the next blanking alignments until the image is correctly
framed or the unwanted information is blanked out.
To enter a blanking alignment, push the control disk up or down to
highlight a function and press ENTER to activate this function.
Press EXIT to return.
BLANKING
TOP
BOTTOM
LEFT
RIGHT
Select with or
then < E NTE R>
<EXIT> to return
Bottom blanking
Adjustment of the blanking on the of the image
Adjustment of the blanking on the bottom of the image
Correct by pushing the control disk up or
down
Adjustment of the blanking on the left side
Adjustment of the blanking on the right side
Correct by pushing the control disk to the
right or to the left
6-10 5975977 BARCODATA 708 260597
Page 37
Convergence Adjustment
Convergence adjustments affect both the horizontal and vertical
lines of the setup pattern. These adjustments are performed on the
red image while superimposed on the green image and then on the
blue image while superimposed on the green image.
Note : the green convergence adjustments can be added as an
option. When these are available, start always with 'green only'. This
option will also be indicated on the convergence menu.
Highlight first 'Green only' when available by pushing the control disk
up or down and press ENTER to display the convergence adjustment
menu.
Random Access Adjustment Mode
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
COLOR SELECT
Select with or
then <ENTER>
<EXIT> to return.
CONVERGENCE
GREEN ONLY
RED ON GREEN
BLUE ON GREEN
Select with or
then <ENTER>
<EXIT> to return.
The screen area is divided into 25 areas.
Use the control disk to move the box to the desired zone and then
press ENTER to begin the convergence adjustment. Start the
convergence adjustment with zone one and continue as mentioned
in the diagram hereafter.
Use the control disk to make horizontal or vertical convergence
adjustments in the selected zone and then press
box to another zone or
EXIT to return to the Convergence menu.
ENTER to move the
ENTER toggles the control disk between zone selection and
zone adjustment .
EXIT returns to convergence menu
green image
23 9 15 17
25
24 22 8 14 16
4123
5
20 18 6 10 12
21 19 7 11 13
CONVERGENCE
SEL : select area
using
arrow keys
ADJ : adjust area
using
arrow keys
Toggle between
SEL and ADJ
with <ENTER>
<ENTER> continue
<EXIT> to return
CONVERGE
ADJUSTMENT
70
5975977 BARCODATA 708 260597
red image
6-11
Page 38
Random Access Adjustment Mode
6-12 5975977 BARCODATA 708 260597
Page 39
Service Mode
7
SERVICE MODE
Starting up the Service mode.
Use the control stick to highlight
Some items in the Service mode are password protected (when the
password function is active). Enter your password to continue. All
other password protected items are now also available if you stay in
the adjustment mode.
ENTER continues to the Service Mode main menu.
EXIT returns to the Operational mode.
The service items are combined in two service menus. To switch
from the first to the second menu or vice versa, push the control stick
forward or backward to select 'more...'
'Service'
and then press ENTER.
ADJUSTMENT MODE
Select a path from
below :
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
Select with or
then <ENTER>
<EXIT> to return.
IRIS
source 1
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
Select with or
then <ENTER>
<EXIT> to return.
Overview flowchart 'Service' mode.
PROJECTOR SET UP
SERVICE MODE
MEMORY MANAGEMENT
COMMON SETTINGS
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE
BARCO LOGO
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
G2 ADJUSTMENT
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
I2C DIAGNOSTICS
5975977 BARCODATA 708 260597
7-1
Page 40
Service Mode
Projector Set-up
Highlight
the control disk up or down and press
ENTER to display the projector set-up
menu.
Within the projector set-up menu, the following items can be consultated or set to
the desired setting :
- Identification
- Total run time
- Change password
- Change language
- Change projector address
- Change baudrate
- Power up mode
- BARCO logo
'Projector Set-Up'
by pushing
Identification
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
Select with or
then <ENTER>
<EXIT> to return.
PROJECTOR SET-UP
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
IDENTIFICATION
TOTAL RUN TIME
BARCO LOGO
Select with or
then <ENTER>
<EXIT> to return.
Highlight
'Identification'
with the control disk and press ENTER.
ENTER will start the selected item.
EXIT returns to the Service mode menu.
The 'Identification' screen gives information concerning :
- Projector address. To change the address of your projector, contact
a qualified service technician.
- Software version.
- Configuration.
Possible installations :
* Front-ceiling
* Front-table
* Rear-ceiling
* Rear-table
- Baud rate PC : transfer speed for communication with an IBM PC (or
compatible) or MAC. The baud rate of the projector must be the
same as the baud rate of the connected computer. When there is
a difference, contact a qualified service technician to make the
appropriate changes.
- Text ON/OFF
Indicates in operational mode if the bar scale and number indicator
will be displayed and if warnings and failures will be displayed.
ON : displayed
OFF : not displayed
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
Select with or
then <ENTER>
<EXIT> to return.
DATA 708
Proj. address : 001
Soft. Version : 6.00
Config. : Ceiling
Baudrate PC : 9600
Text : ON
Serial No. : 103589552
Front
The status can be changed by pressing the 'TEXT' key once on the
RCU.
- Serial no. : indicates the fabrication number of the projector. This
number can be useful when calling for technical assistance.
7-2 5975977 BARCODATA 708 280597
Page 41
Total Run Time
Service Mode
Highlight
'Total Run Time'
with the control disk and press ENTER to
display the amount of time the projector has played since its first start
up at the factory.
ENTER gives the selected item.
EXIT returns to the Service mode menu.
ADJUST returns to the Operational mode.
Note : all projectors leave the factory after a burn-in period of
approximately 100 hours.
Change password
This item is password protected.
Highlight
The current password is displayed. The new password must consist
of 4 digits between 0 and 9. Push the control disk to the left or to the
right to select the digits to be changed. Use the numeric keys to enter
the new digits.
Press
password, a confirmation screen will be displayed.
Press
new password.
When the displayed password is correct, press
If not correct, press
'Change Password'
with the control disk and press ENTER.
ENTER will display the selected item.
EXIT will return to the Path Selection main menu.
ADJUST will return to the Operational mode.
ENTER to save the new password. Before saving the new
EXIT to return to the Projector Set-up menu without saving the
ENTER to save.
EXIT to cancel the saving.
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
Select with or
then <ENTER>
<EXIT> to return.
PASSWORD
Enter new password :
0 0 0 0
Use and to select,
and reprogram
with numeric keys.
<ENTER> to confirm
<EXIT> to return
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
Select with or
then <ENTER>
<EXIT> to return.
CHANGE PASSWORD
ENTER saves the entered password.
EXIT returns without saving.
Change Language
The 'Change Language' function offers the possibility to change the
language of the screen menus to :
- English
- Spanish
- French
- German
Highlight
Push the control disk up or down to select the desired language and
press
'Change Language'
with the control disk and press ENTER.
ENTER selects the Change language menu.
EXIT returns to the Service menu.
ENTER to change the language.
Password will be
reprogrammed as xxxx
<ENTER> to confirm
<EXIT> to cancel
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
Select with or
then <ENTER>
<EXIT> to return.
Select with or
then <ENTER>
<EXIT> to return.
LANGUAGE
ENGLISH
ESPAÑOL
FRANCAIS
DEUTSCH
5975977 BARCODATA 708 260597
7-3
Page 42
Service Mode
Change Projector Address
Every projector requires an individual address between O and 255.
This address can be software installed.
To change that address, push the control disk up or down to highlight
'Change Porjector Address' and press
ENTER. The Change Projec-
tor Address menu will be displayed and the actual address will be
filled in.
ENTER displays the 'Change Projector Address' menu.
EXIT returns to the Service mode main menu.
The first digit is highlighted. Select the individual digits by pushing the
control disk to the right or to the left. Reprogram with the digit keys
on the RCU.
Press
ENTER to confirm.
EXIT to return to the projector set up menu.
Press
Change baudrate
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
Select with or
then <ENTER>
<EXIT> to return.
PROJECTOR ADDRESS
Enter new projector
Use and to select,
with numeric keys.
Highest address is 255
<ENTER> to confirm
<EXIT> to return.
address :
0 0 0
and reprogram
The communication speed between projector and computer has 8
possible speeds. The baud rate speed can be software set up.
Highlight 'Change Baudrate' by pushing the control disk up or down
and press
ENTER to display the Baud rate menu.
The following baud rates are available :
- 9600
- 4800
- 2400
- 1200
- 600
- 300
- 150
- 110
The actual baud rate will be highlighted. To change the baud rate,
push the control disk up or down or to the left or to the right to select
the desired baud rate and press
ENTER to accept this baud rate.
ENTER to accept the selected baud rate.
EXIT to return without changing the baud rate.
Power up mode
When pressing the power switch, the projector can start up in
'operating mode' or in 'stand-by mode'.
Operating mode : the projector start up and displays image .
Stand-by mode : the projector start up in stand-by and waits until the
stand-by button or a digit key is pressed.
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
Select with or
then <ENTER>
<EXIT> to return.
Select new
baudrate :
9600 4800
2400 1200
600 300
150 110
Select with arrow
keys ;
<ENTER> to accept
<EXIT> to return.
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BAUDRATE
BARCO LOGO
To change the Power up mode, select Power Up mode by pushing
the control disk up or down and press
ENTER to toggle between
'Operating' and 'Standby'.
Select with or
then <ENTER>
<EXIT> to return.
ENTER to toggle between operating and standby.
EXIT to return to the Service menu.
7-4 5975977 BARCODATA 708 280597
Page 43
BARCO_logo
The BARCO logo can be added to the image, in overlay or in
background, on any place on the screen.
To add the BARCO logo or to change a setting in the BARCO logo
menu, highlight 'BARCO logo' by pushing the control disk up or down
and press
WARNING : Continuous use of the BARCO logo damages the
RED CRT.
The BARCO logo menu will be displayed on the screen. Within this
menu, four toggle settings are available.
Mode [ON/OFF] :
ON : BARCO logo will be displayed on the screen.
To position the logo on the screen, push the control disk up, down,
to the left or to the right until the desired position is reached.
OFF : No BARCO logo displayed on the screen.
Size [SMALL/LARGE] :
SMALL : Small BARCO logo will be displayed if mode is on.
LARGE : Large (double size) BARCO logo will be displayed if
mode is on.
ENTER to select.
ENTER displays the BARCO logo menu.
EXIT returns to the Service menu
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
Select with or
then <ENTER>
<EXIT> to return.
BARCO LOGO
MODE : ON
SIZE : SMALL
BACKGROUND : ON
ORBITTING : ON
You can move the logo
on the screen, using
the arrow keys.
WARNING : continuous
use of the BARCO logo
damages the RED CRT !
Select with or
<ENTER> to toggle
<EXIT> to return.
Service Mode
Background [ON/OFF] :
ON : BARCO logo will be displayed on a black background.
BARCO
OFF : BARCO logo will be displayed without any background.
BARCO
Orbiting [ON/OFF] :
ON : on the BARCO logo will orbit around it axis.
OFF : no orbit of the BARCO logo.
Memory management
Highlight
down and press ENTER to display the memory management menu.
Within the memory management menu, the following items can be
consultated or executed :
- copy a block
- delete a block
- delete all blocks
- all settings to midposition
- R & B convergence to mid
- Gr convergence mid (only if green convergence is available)
'Memory management'
by pushing the control disk up or
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
Select with or
then <ENTER>
<EXIT> to return.
MEMORY MANAGEMENT
DELETE A BLOCK
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
COPY A BLOCK
5975977 BARCODATA 708 260597
Select with or
then <ENTER>
<EXIT> to return.
7-5
Page 44
Service Mode
Copy a block
The copy a block function copies the settings of a selected block into
the active block.
Highlight
copy a block
with the control disk and press ENTER.
ENTER will select the highlighted item.
EXIT returns to the Path Selection main menu.
ADJUST returns to the Operational mode.
MEMORY MANAGEMENT
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
To copy the settings of a closed block to the block you are working
on (active block), use the control disk to select a block.
All existing settings will be overwritten with the new settings.
Press
ENTER to copy the selected block. A confirmation screen will
be displayed.
ENTER displays a confirmation screen.
EXIT returns to the Service Mode main menu.
If you are certain you wish to copy the contents of the selected block
into the active block, press
ENTER.
EXIT cancels the copy procedure and returns without copying the
block.
Deletion of blocks
This item is password protected.
The delete function is used to clear all data (settings) from an
adjustment block.
A delete can be given :
- block by block
or
- for all blocks.
Select with or
then <ENTER>
<EXIT> to return.
Nr. Src Fh Fv inp conf
1 1 15.6 50 video FC
2 3 31.2 60 RGB3S RT
3 - 15.6 50 intern FC
4 2 31.5 50 RGB3S FC
5 - 33.7 60 intern FC
6
7
8
COPY MODE
Active block nr. 1
Select with or
<ENTER> to copy
<EXIT> to return.
All settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
COPY BLOCK
Deleting block by block
The '
delete a block'
Highlight
'Delete a block'
ENTER will select the pointed item.
EXIT returns to the Path Selection main menu.
ADJUST returns to the Operational mode.
Push the control disk up or down to select the desired adjustment
block. Press
confirmation menu will be displayed.
ENTER displays the confirmation menu.
EXIT returns to the Service Mode main menu.
ENTER will delete the selected block.
EXIT cancels the deletion procedure and returns to the Service mode
main menu.
function deletes the settings of a selected block.
with the control disk and press ENTER.
ENTER to delete the selected adjustment block. A
MEMORY MANAGEMENT
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
Select with or
Select with or
then <ENTER>
then <ENTER>
<EXIT> to return.
<EXIT> to return.
DELETE MODE
Nr. Src Fh Fv inp conf
1 1 15.6 50 video FC
2 3 31.2 60 RGB3S RT
3 - 15.6 50 intern FC
4 2 31.5 50 RGB3S FC
5 - 33.7 60 intern FC
6
7
8
Select with or
<ENTER> to copy
<EXIT> to return.
Active block nr. 1
DELETE BLOCK
The selected block
will be deleted !
<ENTER> to confirm
<EXIT> to cancel
7-6 5975977 BARCODATA 708 280597
Page 45
Service Mode
Deletion of all blocks
Highlight
If you are certain you wish to delete all blocks, press ENTER to
confirm, otherwise press EXIT to return.
Once
are permanently removed and cannot be restored.
'delete all blocks'
with the control disk and press ENTER.
ENTER gives a confirmation message before deleting.
EXIT returns to the Path Selection main menu.
ENTER is pressed, all block headers and adjustment settings
All settings to midposition
Item is password protected.
Highlight
ENTER to set all settings to their midposition.
A confirmation menu will be displayed first.
'All settings to midposition'
with the control disk and press
ENTER displays a Confirmation screen.
EXIT returns to the Service menu.
MEMORY MANAGEMENT
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
Select with or
then <ENTER>
<EXIT> to return.
All block
will be deleted !
<ENTER> to confirm
<EXIT> to cancel
MEMORY MANAGEMENT
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
DELETE ALL BLOCK
ENTER will set all settings to their midposition. EXIT will cancel the
operation to set all settings to their midposition.
Undo all settings to midpos
When "All settings to midpos" is selected, all settings are set to their
midposition. To cancel this action, select 'Undo all settings to
midpos' by pushing the control disk up or down and press ENTER.
'Undo all settings to Midposition' is displayed in the Memory management menu in stead off 'All settings to midposition' when this
latter is pressed.
An undo is possible as long as the projector is playing on the same
source (= same adjustment block) even when some adjustments as
geometry or convergence are already readjusted. When undo is
presssed all settings are reset to the previous settings.
Select with or
then <ENTER>
<EXIT> to return.
SET TO MIDPOSITION
All settings
on current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
MEMORY MANAGEMENT
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
UNDO ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
Select with or
then <ENTER>
<EXIT> to return.
5975977 BARCODATA 708 260597
7-7
Page 46
Service Mode
R & B convergence mid
Item is password protected.
Highlight
ENTER to set all convergence settings to their midposition. A
confirmation screen will be displayed first.
'R & B convergence mid'
with the control disk and press
MEMORY MANAGEMENT
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
ENTER sets the convergence settings to their midposition. EXIT
cancels the procedure to set the convergence settings to their
midposition.
Undo R & B convergence mid
When "R & B convergence mid" is selected, all convergence settings
are set to their midposition. To cancel this action, select 'Undo R &
B convergence mid' by pushing the control disk up or down and press
ENTER. 'Undo R & B convergence mid' is displayed in the Memory
management menu in stead off 'R & B convergence mid' when this
latter is pressed.
An undo is possible as long as the projector is playing on the same
source (= same adjustment block) even when some adjustments are
already readjusted. When undo is presssed all settings are reset to
the previous settings.
Green convergence mid
Only available when the projector is equipped with green convergence adjustmentes.
Highlight 'Gr convergence mid' by pushing the control disk up or
down and press
ENTER to switch off the green convergence.
Select with or
then <ENTER>
<EXIT> to return.
R & B CONVERGENCE MID
Convergence settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
MEMORY MANAGEMENT
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
UNDO R & B CONVERGENCE MID
GR CONVERGENCE MID
MEMORY MANAGEMENT
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
COPY A BLOCK
DELETE A BLOCK
Select with or
then <ENTER>
<EXIT> to return.
COPY A BLOCK
DELETE A BLOCK
Select with or
then <ENTER>
<EXIT> to return.
Undo green convergence mid
Only available when the projector is equipped with green convergence adjustmentes.
The item 'Undo green convergence mid' will automatically be displayed when the green convergence is switched to midposition.
Press
ENTER to switch on the green convergence.
7-8 5975977 BARCODATA 708 280597
MEMORY MANAGEMENT
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
UNDO GR CONVERGENCE MID
Select with or
then <ENTER>
<EXIT> to return.
Page 47
Common Settings
SAFETY
NOTICE
RISK OF ELECTRICAL SHOCK
G2 ADJUSTMENT SHOULD BE
PERFORMED
BY BARCO PERSONNEL,
OR BARCO AUTHORIZED
DEALERS.
IF QUALIFIED, PRESS
<ENTER> TO CONTINUE, OR
IF NOT, <EXIT> TO RETURN.
Service Mode
Highlight
'Common settings'
by pushing the control disk up or down
and press ENTER to display the common settings menu.
Within the common settings menu, the following items can be set up
or executed :
- G2 adjustment
- CRT run in cycle
- Projector warm up
G2 Adjustment
Item is password protected.
Highlight '
continue.
A safety notice will be displayed on the screen as it is necessary to
open the top cover to adjust the G2.
G2 adjust
' with the control disk and press
ENTER
to
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
Select with or
then <ENTER>
<EXIT> to return.
COMMON SETTINGS
G2 ADJUSTMENT
CRT RUN IN CYCLE
PROJECTOR WARM UP
Select with or
then <ENTER>
<EXIT> to return.
COMMON SETTINGS
G2 ADJUSTMENT
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
ENTER selects the G2 adjustment.
EXIT returns to the Common settings menu.
ADJUST returns to the Operational mode.
'G2 adjustment should be performed by BARCO personnel, or
BARCO authorized dealers'.
If you are qualified, press ENTER to continue. If not qualified, press
EXIT to return to the Common settings menu. Further description of
the G2 adjustment is given in the Installation manual.
CRT run in cycle
The CRT run in cycle option can only be activated when memory
blocks on an internal # pattern are available. When one or more such
blocks are available, a flashing white image (5sec on, 5 sec off) is
generated and that for 5 min on the first internal block. In the next 5
min, a second internal block will be used to generate the flashing
white image. The image will also be shifted in a vertical way to
prevent a CRT burn in. To quit the CRT run in cycle option, press
EXIT.
Highlight
start.
'CRT run in cycle'
with the control disk and press ENTER to
Select with or
then <ENTER>
<EXIT> to return.
COMMON SETTINGS
G2 ADJUSTMENT
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
Select with or
then <ENTER>
<EXIT> to return.
ENTER selects the CRT run in cycle option.
EXIT returns to the Path Selection main menu.
5975977 BARCODATA 708 260597
7-9
Page 48
Service Mode
If a memory block adjusted on an internal # pattern is available, the
CRT run in cycle will start when pressing ENTER. If no such a block
is available, the projector cannot run the CRT run in option and leaves
the adjustment mode.
If you still want to run CRT run in cycle, create first a memory block
on an internal # pattern and restart the CRT run in option.
ENTER starts the 'CRT run in' when an internal generated # pattern
is available.
EXIT returns to the Path Selection main menu.
Projector warm up
CRT RUN IN CYC LE
A flashing white pattern
will be generated until
<EXIT> is pressed.
The projector only uses
memory blocks adjusted
on an internal # pattern;
if no such block is
available, the pr o ject or
can't run the procedure
and leaves the adjustment
mode.
<ENTER> to continue
<EXIT> to cancel
Highlight 'Projector warm up' by pushing the control disk up or down
and press
ENTER to select the projector warm up menu.
The ON/OFF option can be toggled with the ENTER key.
When in the ON position (and the CRT run in cycle is OFF), the
projector can start up with a warm up periode of 20 minutes. During
the start up a warm up menu will be displayed. This menu offers the
possibility to skip the warm up periode anyway by pressing the
EXIT
key and offers the possibility to adjust the horizontal and vertical
amplitude of this white image with the control disk. During this warm
up period, a full white image is shifted on the CRT faceplate to avoid
a burn in.
Every 30 seconds a text box will be displayed on another place on the
screen with the remaining time to go.
When
EXIT is pressed during this warm up periode, the warm up
menu will be redisplayed with the remaining time indication. Press
another time
EXIT to interrupt the warm up cycle.
When the warm up option is OFF, when switching on the projector,
it starts immediately with the projection of the selected source.
COMMON SETTINGS
G2 ADJUSTMENT
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MDOE
Select with or
then <ENTER>
<EXIT> to return.
PROJECTOR WARM UP
OPTION : ON
A FULL WHITE PATTERN
WILL BE GENERATED FOR
20 MINUTES AT POWER UP
AFTER THIS PROCEDURE
THE PROJECTOR IS READY
TO PERFORM IN OPTIMUM
CONDITION
TOGGLE OPTION ON OR OFF
with <ENTER>
<EXIT> to return
CRT Drive Mode
The projector CRT's can be driven with the normal current (normal
mode), a lower current (economic mode) or with a higher current
(boost mode).
To change the drive mode, highlight 'CRT drive mode' by pushing the
control stick forward or backward and press ENTER to display the
CRT drive mode menu.
To change the boost mode, push the control disk up or down to select
a display mode and press ENTER to select.
The following modes are available :
- Normal
- Economic : Lower drive current to the CRT's, the lifetime of the
CRT's will enlarge but the light output will reduce.
- Tempory boost : Higher drive current to the CRT's, the lifetime of the
CRT's will shorten but the light output will be higher. This situation
is tempory, when restarting the projector, the drive mode is automatically set to normal.
- Permanent boost : Higher drive current to the CRT's, the lifetime of
the CRT's will shorten but the light output will be higher. This setting
will be saved in the EEPROM. When restarting the projector, it will
start up in boost mode.
7-10 5975977 BARCODATA 708 280597
COMMON SETTINGS
G2 ADJUSTMENT
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MDOE
Select with or
then <ENTER>
<EXIT> to return.
CRT DRIVE MODE
TEMPORARY BOOST
PERMANENT BOOST
WARNING : permanent
boost mode reduces the lifetime
Select with or
then <ENTER>
<EXIT> to return.
NORMAL
ECONOMIC
of the CRT's !
Page 49
Service Mode
A warning, permanent BOOST mode in use, will be displayed to
inform the user.
When text is on, this warning will be repeated every time a new
source is selected.
I2C Diagnostics
Highlights 'I2C Diagnostics' by pushing the control disk up or down
and press
The I2C diagnostics menu gives an overview of the I2C failures
inside the projector.
To scroll through the failure list, push the control disk up or down.
The I2C address, IC number and module name will be given in I2C
diagnostic menu.
When no errors are detected, the following message will appear on
the screen :
"No errors on i2c-bus detected".
ENTER.
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
Select with or
then <ENTER>
<EXIT> to return.
addr IC number
48H IC200 DECODER
WARNING
PERMANENT
BOOST MODE
IN USE !
I2C DIAGNOSTICS
Failures :
mod.name
Scroll with or
then <ENTER>
<EXIT> to return.
5975977 BARCODATA 708 260597
7-11
Page 50
Service Mode
7-12 5975977 BARCODATA 708 280597
Page 51
Messages, warnings and failures
8
INPUT 01
Fh= 15.6 kHz
Fv= 050 Hz
SOURCE 01
enter
password
x x x x
text on
text off
PROJECTOR
ADDRESS :
003
MESSAGES, WARNINGS AND FAILURES
When selecting a new source, information about this source will be
displayed on the screen. Source
number, horizontal and vertical frequencies of the displayed source.
Announcement of the selected
source.
Message to enter your password.
Password contains 4 digits.
These messages will be displayed
on the screen when pushing the
TEXT key.
Text ON : the
will be enabled during the change of
an analog control in the
mode'
will be displayed.
Text OFF : the
will be disabled during the change
of an analog control in the
tional mode'
failures will not be displayed.
Indication of the projector address
when activating the
button on the RCU with a pencil or
other small object.
'bar scale indication'
'operational
+ all warnings and failures
'bar scale indication'
'opera-
+ all warnings and
'ADDRESS'
WARNING :
invalid
code entry
WARNING :
end of adjust range
WARNING :
input no
longer
available
WARNING :
input se-
lector not
available
WARNING :
invalid
frequency
input
table is
deleted
Message when the entered password is wrong.
End of adjustment range.
Message will be displayed when
the input source is no longer available. The following message then
appears:
lect new source'
It warns you to check the power
connection or the power status of
the RCVDS.
Next message will appear
immediatly on the screen :
stand-by'
The entered frequency or applied
frequency of the source is out of the
projector's range.
Message to inform that selected
table is deleted. This message will
be followed by
on which the user has to answer.
'check input signal or se-
.
'confirm message'
.
'go to
,
WARNING :
input not
available
WARNING :
source not
available
WARNING :
invalid
key entry
5975977 RETRODATA 708 260597
When using the projector with the
RCVDS, this warning will be displayed when selecting an input slot
of an RCVDS where the input board
is missing.
The input is a valid input but the
source is not connected to the
input terminals or the input source
is switched off.
When a wrong key is pressed on
the RCU.
FAILURE
I2C error
addr. : 7FH3
FAILURE
short
circuit on
I2C bus
Hardware failure. Call a qualified
service technician for repair.
Hardware failure. Call a qualified
service technician for repair.
1-1
Page 52
Messages, warnings and failures
FAILURE
RCVDS com-
munication
error
FAILURE
IRIS commu-
nication
error
WAIT
starting
up
IRIS
FAN FAILED
Projector
will
switch off
Serial communication error between the RCVDS and the projector.
Communication error between IRIS
800 and the projector. Call a qualified service technician.
Message during the start up of the
IRIS. Message will disappear when
the IRIS is ready to accept commands.
Message when one of the fans are
not working anymore. Projector
switches to stand-by
8-2 5975977 BARCODATA 708 260597
Page 53
Options
9
OPTIONS
IR Receiver 800
This infrared receiver unit makes it possible to control the projector
from another room.
There is a communication line with cable between the IR receiver and
the projector or the RCVDS05. The control information from the RCU
can now be sent to this IR receiver.
The IR receiver 800 displays the selected source on a 7-segment
display.
Order number : R9827515
Hardwired RCU.
The control signals from the RCU can be sent to the projector via a
wired connection.
shield
conductor
Preparing your remote cable :
Use a shielded cable with a maximum length of 100 m and two mini-
jack 3.5 mm connectors (order number : R3131991).
RCVDS 05 Source Selector
An optional RCVDS05 makes it possible to connect up to 20 sources
to the projector. When RCVDS's are linked via the expansion module,
even 90 inputs can be connected to the projector.
The selected source number will be displayed on a 2 digit display and
the selected input module will be indicated with a LED on the rear.
Order Numbers RCVDS 05: 110V: 9827888
9827889
220V: 9827880
9827881
VS05 Switcher
- Peel back the vinyl covering of the cable on both sides and twist the
wire core.
- Solder a jack plug as shown in drawing above to each end of the
cable.
shield = ground
conductor = data information
When the cable is ready, plug one side in the remote control and the
other side in the connector on the rear of the projector labelled
‘remote’.
Projector Control software
The software is user-friendly and makes full use of : mouse control,
pull down menus and dialog boxes.
Two main applications are available with this software : remote
control and transfering and receiving data of projector settings.
Remote Control Simulation. Advantage : address range 0 to 255.
Adjustment Data : Where can it be located when a IBM PC (or
compatible) or MAC or Workstation is connected :
- Hard memory device with files of settings.
- The contents of the local memory of the computer.
- The contents of the projector.
The VS05 is a versatile Video and HDTV source selector for all
BARCO's digitally controlled large screen projectors. It offers the
possibility to connect and switch up to 5 different Video sources, 3
different S-Video sources and 1 RGB Analog source to a BARCO
projector. In addition, the audio signal proper to the source, can be
switched to an audio amplifier.
Order Numbers: 110V: 9827890
220V: 9827899
IRIS/2 Auto-Convergence System
Easy-to-use, high precision automatic convergence system.
Convergence time : less than 2'30''
Various options on the menu offer you the optimal solution for your
own individual needs :
- Align : Convergence starts from the current image situation
- Align from midposition : Convergence starts from midposition
- Touch-up : Convergence starts when the source switches or after
a user-defined time : alignment of static convergence almost
invisible for the audience.
5975977 BARCODATA 708 260597
9-1
Page 54
Options
MAGIK Interface
Multifuctional Analog Graphics Interface Kit.
BARCO's MAGIK interface allows the user to connect a presentation
device such as a projector or a professional monitor to any computer
with analog video signal with or without maintaining the connection
with its own display. The MAGIK interface buffers and amplifies any
RGB analog signal with TTL or analog sync without signal loss or
image degradation.
The MAGIK can be delivered together with connection cables for PC,
MAC, SUN or workstation in a nice handbag case.
Order numbers MAGIK with cables and case :
R9828120 (230V)
R9828129 (120V)
Order number MAGIK only :
R9828121 (230V)
R9828128 (120V)
Orbiting Kit
Static pictures are very often shown on large screen projectors,
especially in process control and presentation applications. Due to
the fact that the same picture information is shown for a long period
in the same place, picture tubes can be damaged by 'local burn-in'. To
reduce this problem, a special Orbiting circuit is available which
moves the picture very slowly around a predefined screen area. The
cycle time is very long to make the movement of the projected image
imperceptible.
The use of the orbiting kit is described in appendix A in the installation
manual.
Order number : R9827780
Line Doubler Kit
BARCO's line doubler kit consists of a video decoder with a three-line
adaptive Comb filter, an enhancement circuit and the line doubler
itself.
- The three-line adaptive Comb filter improves color transitions and
reduces noise in the video signal.
- The enhancement circuit integrated in the decoder provides sharper
images with clearer outlines.
- The line doubler circuit reduces visible line structure by doubling the
number of lines of the video image.
These three circuits work in unison to produce a smoother yet
sharper image which is significantly more appealing when watching
video images.
Order number : R9828161
Ceiling mount CM50
This suspension system enables to mount any projector from the
BARCO 700 series to the ceiling without using any mechanical
interface, and to adapt the projector perfectly to the local mounting
requirements.
Order number CM50 with pulley : R9827990
Order number CM50 without pulley : R9827991.
Adapter and communication cables
BARCO provides several cables to connect peripheral equipment to
the projector.
a. D9-D9 communication cable
- To connect an IBM PC (or compatible) to the projector.
- To connect a RCVDS05 to the projector.
- To connect a IR receiver to the RCVDS05 to the projector.
- To be used as extension cable for all other adapter cables.
Available length :5 m (16ft), order number R982770; 15 m(50ft), order
number R9827560; and 30 m (100ft), order number R9827570
b. Din Mini8-D9 adapter cable.
- To connect a Macintosh computer to the RETROGRAPHICS 808s.
Available length : 1 m (3,2 ft), order number R9827640.
c. D25-D9 adapter cable
- To connect a workstation to the RETROGRAPHICS 808s.
Available length : 1 m (3,2 ft), order number R9827630
d. 5 BNC to 5 BNC cable
- To connect an analog source to the BNC input of the projector
Available lenght : 60 cm, order number R9828260
150 cm, order number R9828261
5 m, order number R9828262
15 m, order number R9828263
Soft edge matching kit
Multi-screens are popular for many applications. In these installations, the goal is to obtain a contiguous matched image, forming one
homogenous view. The soft edge matching feature provides a
solution to the annoying side effects when adjusting two or more
projected images next to each other. To improve this junction, both
images must be overlapping within a certain percentage of the total
screen width. During the overlapping period, both video signals are
modulated by appropriate waveforms so that the resulting light output
equals the rest of the image.
Contrast modulation kit
The contrast modulation kit is designed to improve overall light output
uniformity and to overcome the inherent color shift errors, normally
associated with CRT projection. The laws of physics applied to
projection optics dictate that the center of the projected image will be
brighter than the corners, this phenomenon is normally referred to as
'corner fall off'. Due to the normal off-axis projection of the red and
blue images, CRT projection displays a phenomenon referred to as
'color shift', whereby one side of the image is reddish and the other
blueish. By modulating the amplitude of the video signal with
appropriate waveforms we are able to overcome both problems.
The use of this contrast modulation kit is described in appendix C.
Order number : R9827800
9-2 5975977 BARCOGRAPHICS 708 260597
Page 55
Adjustment Blocks and Source Numbers 90-99
A
ADJUSTMENT BLOCKS AND SOURCE
NUMBERS 90 - 99
Adjustment Blocks (memory blocks)
As the projector is digitally controlled, all geometry and convergence adjustments are stored in the projector’s memory as numeric
values. These numeric values are used to control digital potentiometers which in turn, control the projector. Each source connected
to the projector has a unique set of adjustment data which is automatically downloaded into the projector’s digital potentiometers once
the source has been selected. This set of adjustment data is referred to as an
An adjustment table is automatically created for a source when the source is first connected to the projector and the Adjustment mode
is entered. If other sources have already been connected to the projector and geometry and convergence adjustments have been
performed on these sources, the projector will use Linear Digital Interpolation to create a new block for the new source. This block will
provide an initial set of adjustments for the new source that have been calculated by the projector from “previous experience”.
The projector’s memory has the capacity to store 32 adjustment blocks. The adjustment block consists of two parts, the block header
and the data representing the values for all adjustments (eg. Convergence and Geometry) in the projector for the source the block
corresponds to. The block header contains the basic characteristics of the source and the projector configuration used to display the
source.
Block Header example of block header
Block Number 01
Source Number 01
Horizontal Frequency 15.6 kHz
Vertical Frequency 50 Hz
Input Type video
Scan Switch Configuration Front/Ceiling
“adjustment block”
.
The data representing the various adjustments for the source follows the block header.
Source numbers 90 - 99
Source numbers 90 - 99 do not correspond to physical inputs
to the projector or RCVDS. They are used to assign an
additional adjustment block to a source. This additional adjustment block may contain different geometry and convergence
settings, sync fast/slow positions and enhanced blue on/off
settings. The relationship between source numbers 0 - 9 and
90 - 99 (projector with RCVDS) or 1 - 5 and 91 - 95 (stand-alone
projector) is shown in the diagram below.
The alternate adjustment block for sources 0 - 9 (projector with
RCVDS) or 1 - 5 (stand-alone projector) is activated by selecting the
corresponding source number 0 - 9 (projector with RCVDS) or 1 - 5
(stand-alone projector). Once this source number is selected, the
alternate block of adjustment data is in use and may be modified via
the adjust mode of the projector. The alternate adjustment block is
automatically stored.
source input 0
source input 1
source input 2
source input 9
2. Select the corresponding source number between 90 and 99. The
adjustment block for the source number between 0 and 9 is copied to
the corresponding source number between 90 and 99.
3. Enter the adjust mode and make any desired changes (geometry,
convergence, sync fast/slow, enhanced blue on/off) to the second
adjustment block.
source number 0
source number 90
source number 1
source number 91
source number 2
source number 92
source number 9
source number 99
Block header A
Block header A, different analog settings
Block header B
Block header B, different analog settings
Block header C
Block header C, different analog settings
Block header J
Block header J, different analog settings
Follow the steps below to create a second adjustment block for a
source between 0 and 9.
1. Select the source between 0 and 9 that the second adjustment
block is to be created for.
5975977 BARCODATA 708 260197
4. Exit the adjust mode.
Note : the above also applies to source number 1 - 5 and 91 - 95 of
a stand alone projector (no RCVDS)
A-1
Page 56
Adjustment Blocks and Source Numbers 90-99
A-2 5975977 BARCODATA 708 260597
Page 57
INSERT CARD
Insert Card
"
RCU
INPUT S O URCE S
PROJECTOR
1
2
3
4
5
6
7
INPUT SO URCE S
RCVDS
1
2
3
5
6
7
8
9
10
RCU
INPUT S O URCE S
PROJECTOR
1
P
2
3
4
5
6
7
INPUT SO URCE S
RCVDS
1
2
3
5
6
7
8
9
10
P
5975977 BARCODATA 708 260597
i-1
Loading...