Barco R9002119, R9002110 User Manual
BARCO PROJECTION SYSTEMS
Date :
210397
RETRODATA
808s
R9002110
R9002119
INSTALLATION MANUAL
Art. No. :
R5975198
Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, March 1997.
All rights reserved.
Trademarks are the rights of their respective owners.
Printed in Belgium
BARCO nv/Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Printed in Belgium
Table of Contents
Table of contents ............................................................................................................................................................................ i-1
Safety Instructions ......................................................................................................................................................................... 1-1
Unpacking and Projector Dimensions .......................................................................................................................................... 2-1
Unpacking.................................................................................................................................................................................. 2-1
Projector dimensions ................................................................................................................................................................. 2-2
Installation Set-up .......................................................................................................................................................................... 3-1
Cabinet assembly ...................................................................................................................................................................... 3-1
Mounting the side profiles .......................................................................................................................................................... 3-2
Projector Set-up ............................................................................................................................................................................. 4-1
To gain access to the DIP switches............................................................................................................................................ 4-1
Setting the projector address ..................................................................................................................................................... 4-2
Power-up mode.......................................................................................................................................................................... 4-3
Baud rate for communication with a computer ............................................................................................................................ 4-4
Password mode ......................................................................................................................................................................... 4-4
AC Power Connection.................................................................................................................................................................... 5-1
AC power cord connection ......................................................................................................................................................... 5-1
Preparing your power cord ......................................................................................................................................................... 5-1
AC power check......................................................................................................................................................................... 5-2
AC input power (mains) voltage adaptation ................................................................................................................................ 5-2
Switching on the projector .......................................................................................................................................................... 5-4
Source Connection ........................................................................................................................................................................ 6-1
Signal input connection on the projector ..................................................................................................................................... 6-1
Connecting a composite video source to port 1 .......................................................................................................................... 6-1
Connecting a S-Video or Video source to port 2 ......................................................................................................................... 6-2
Connecting a RGB Analog source to port 3 ................................................................................................................................ 6-3
Connecting a RGB Analog source to port 4/5 ..................................................................................... ........................................ 6-4
Connecting a RGB Analog source with Tri-level sync to port 4/5 ................................................................................................ 6-4
Connecting a component video source to port 4/5 ...................................................................................................................... 6-5
Connecting a component video source with Tri-level sync to port 4/5 ............................................................ ............................. 6-5
Connecting external loudspeakers to the retroprojector .............................................................................................................. 6-6
Peripheral equipment ................................................................................................................................................................. 6-6
Connecting a RCVDS 05 switcher to the retroprojector .............................................................................................................. 6-6
Connecting a VS05 switcher to the retroprojector ....................................................................................................................... 6-6
Connecting an IR remote receiver to the retroprojector............................................................................................................... 6-6
Appendix A : Orbiting ....................................................................................................................................................................... A-1
Appendix B : G2 adjustment............................................................................................................................................................. B-1
Appendix C : Gamma corrections ................................................................................................. .................................................... C-1
5975198 RETRODATA 808s 210397
i-1
Safety Instructions
1
SAFETY INSTRUCTIONS
Notice on Safety
This equipment is built in accordance with the requirements of the
international safety standards EN60950, UL 1950 and CSA C22.2
No.950, which are the safety standards of information technology
equipment including electrical business equipment.
These safety standards impose important requirements on the use of
safety critical components, materials and isolation, in order to protect
the user or operator against risk of electric shock and energy hazard,
and having access to live parts.
Safety standards also impose limits to the internal and external
temperature rises, radiation levels, mechanical stability and strength,
enclosure construction and protection against the risk of fire.
Simulated single fault condition testing ensures the safety of the
equipment to the user even when the equipment's normal operation
fails.
INSTALLATION INSTRUCTIONS
Before operating this equipment please read this manual
thoroughly, and retain it for future reference.
Installation and preliminary adjustments should be performed
by qualified BARCO personnel or by authorized BARCO
service dealers.
WARNING
TO PREVENT FIRE OR ELECTRICAL SHOCK
HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE
FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT)
This equipment has been tested and found to comply with the limits
of a class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Note :
The use of shielded cables is required to comply within the limits of
Part 15 of FCC rules and EN55022.
* All the safety and operating instructions should be read before using
this unit.
* The safety and operating instructions manual should be retained for
future reference.
OWNER’S RECORD
The part number and serial number are located at the back side of the
projector. Record these numbers in the spaces provided below.
Refer to them whenever you call upon your BARCO dealer regarding
this product.
PART NUMBER :
SER. NUMBER :
DEALER :
The lightning flash with an arrowhead within a
triangle is intended to tell the user that parts
inside this product may cause a risk of electrical
shock to persons.
The exclamation point within a triangle is intended to tell the user that important operating
and/or servicing instructions are included in the
technical documentation for this equipment.
5975198 RETRODATA 808s 210397
* All warnings on the equipment and in the documentation manuals
should be adhered to.
* All instructions for operating and use of this equipment must be
followed precisely.
On safety
1. This product should be operated from an AC power source.
This projector may be connected to an IT-power system.
Operating AC power voltage of the projector:
BARCO RETRODATA 808s
Art.No. R9002110 (230V AC)
Art. No R9002119 (120V AC)
Consult your dealer to switch over from 230Vac to 120 Vac or from
120Vac to 230 Vac.
If you are not sure of the type of AC power available, consult your
dealer or local power company.
2. This product is equipped with a 3-wire grounding plug, a plug
having a third (grounding) pin. This plug will only fit into a groundingtype power outlet. This is a safety feature. If you are unable to insert
the plug into the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the purpose of the grounding-type
plug.
WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE
GROUNDED (EARTHED) via the supplied 3 conductor AC power
cable.
(If the supplied power cable is not the correct one, consult your
dealer.)
1-1
Safety Instructions
A. Mains lead (Power cord) with CEE 7 plug:
The wires of the mains lead are colored in
accordance with the following code.
Green and yellow: earth (safety earth)
Blue: neutral
Brown: line (live)
B. Power cord with ANSI 73.11 plug:
The wires of the power cord are colored in
accordance with the following code.
Green/yellow: ground
White: neutral
Black: line (live)
3. Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.
To disconnect the cord, pull it out by the plug. Never pull the cord
itself.
4. If an extension cord is used with this product, make sure that the
total of the ampere ratings on the products plugged into the extension
cord does not exceed the extension cord ampere rating. Also make
sure that the total of all products plugged into the wall outlet does not
exceed 15 amperes.
5. Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electrical shock.
Never spill liquid of any kind on the product. Should any liquid or solid
object fall into the cabinet, unplug the set and have it checked by
qualified service personnel before resuming operations.
6. Lightning - For added protection for this video product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent
damage to the projector due to lightning and AC power-line surges.
On installation
1. Do not place this equipment on an unstable cart, stand, or table.
The product may fall, causing serious damage to it.
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the equipment.
c.If the product has been exposed to rain or water.
d. If the product does not operate normally when the operating
instructions are followed.
Note : Adjust only those controls that are covered by the operating
instructions since improper adjustment of the other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance, indicating
a need for service.
Replacement parts - When replacement parts are required, be sure
the service technician has used original BARCO replacement parts or
authorized replacement parts which have the same characteristics as
the BARCO original part. Unauthorized substitutions may result in
degraded performance and reliability, fire, electric shock or other
hazards. Unauthorized substitutions may void warranty.
Safety check - Upon completion of any service or repairs to this
projector, ask the service technician to perform safety checks to
determine that the product is in proper
operating condition.
On cleaning
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
- To keep the cabinet looking brand-new, periodically clean it with a
soft cloth. Stubborn stains may be removed with a cloth lightly
dampened with mild detergent solution. Never use strong solvents,
such as thinner or benzine, or abrasive cleaners, since these will
damage the cabinet.
- To ensure the highest optical performance and resolution, the
projection lenses are specially treated with an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens,
use a soft dry cloth. Do not use a damp cloth, detergent solution, or
thinner.
2. Do not use this equipment near water.
3. Slots and openings in the cabinet and the back or bottom are
provided for ventilation; to ensure reliable operation of the product
and to protect it from overheating, these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface. This
product should never be placed near or over a radiator or heat
register.
The projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
4. Do not block the projector cooling fans or free air movement under
and around the projector. Loose papers or other objects may not be
nearer to the projector than 4" on any side.
On servicing
Do not attempt to service this product yourself, as opening or
removing covers may expose you to dangerous voltage potentials
and risk of electric shock!
Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to
1-2 5975198 RETRODATA 808s 210397
On repacking
Save the original shipping carton and packing material; they will
come in handy if you ever have to ship your equipment. For maximum
protection, repack your set as it was originally packed at the factory.
On illumination
In order to obtain the best quality for the projected image, it is essential
that the ambient light which is allowed to fall on the screen be kept to
an absolute minimum.
When installing the projector and screen, care must be taken to avoid
exposure to ambient light directly on the screen. Avoid adverse
illumination on the screen from direct sunlight or fluorescent lighting
fixtures.
The use of controlled ambient lighting, such as incandescent spot
light or a dimmer, is recommended for proper room illumination.
Where possible, care should also be taken to ensure that the floors
and walls of the room in which the projector is to be installed are nonreflecting, dark surfaces. Brighter surfaces will tend to reflect and
diffuse the ambient light and hence reduce the contrast of the
projected image on the screen.
Unpacking and dimensions
2
UNPACKING AND PROJECT OR DIMENSIONS
Unpacking
To open the banding around the carton, pull out the clip as shown below :
Take the projector cabinet and the mirror cabinet out of its shipping carton and place them on floor.
Save the original shipping cartons and packing material, they will come in handy if you ever have to ship your retroprojector. For maximum
protection, repack your projector as it was originally packed at the factory.
Contents of the shipping boxes :
❒ 1 RETRODATA 808s, projector cabinet and mirror cabinet.
1 Remote Control Unit plus 1 battery 9V
❒
❒ 1 power cord with outlet plug type CEE7 or ANSI 73.11
❒ 1 Owner's Manual
❒ 1 Installation Manual
5975198 RETRODATA 808s 210397
2-1
Unpacking and dimensions
Projector dimensions (in mm)
70 mm
2.74"
AIRFLOW
77.53"
1969 mm
1535 mm
60.42"
1370 mm
996 mm
54.03"
39.21"
1341.5 mm
747 mm"
29.43"
52.81"
39.25"
997 mm
743 mm
29.25"
32.27"
820 mm
0.85"
22 mm
4.35"
110 mm
1020 mm
40.10"
2-2 5975198 RETRODATA 808s 210397
Installation set-up
3
INSTALLATION SET-UP
Cabinet Assembly
Attention : Avoid touching the screen surface while handling the
screen cabinet in order to avoid any damage of the screen surface.
Lift up the mirror cabinet and place it on the projector cabinet. Both
centering pins on the the mirror cabinet must match the centering
holes in the projector cabinet. Ensure also that the fixation holes in the
mirror cabinet matches the holes in the projector cabinet.
Secure both cabinets with 3 bolts.
Fixation
holes
1
Centering
holes
5975198 RETRODATA 808s 210397
3-1
Installation set-up
Mounting the side profiles
The side profiles are packed during transportation inside the mirror
cabinet (back side).
Turn in the screws a little and slide the profile over the screws.
Fixate the 3 screws.
3-2 5975198 RETRODATA 808s 210397
Projector set-up
P
4
PROJECTOR SET-UP
The DIP switches on the controller unit allow the SET-UP of the
projector :
❒ 8 DIP switches for setting the projector address
r
1 DIP switch for setting the power up mode
r
3 DIP switches for setting the baud rate for communication
r
1 DIP switch for setting the password mode
To gain access to the DIP switches :
Acces to the DIP switches is possible via the backside of the
retroprojector (image 1)
Open the top cover of the controller module by loosening both
retaining screws of the metal protection plate. Pivot this plate
downside (image 2).
2
1
The DIP switches are located on the back side of this metal protection
plate (image 3).
PASSWORD MODE
ASSWORD REQUIRED
FOR ADJUSTMENT
ON
OFF
YES
NO
BAUD RATE TABLE
TO COMPUTER
CODE
0
1
2
3
4
5
6
7
SPEED
110
150
300
600
1200
2400
4800
9600
PROJECTOR ADDRESS
PASSWORD MODE
BAUD RATE CODE
POWER UP MODE
OPERATING MODE WHEN
POWER IS SWITCHED ON
(sum)
RESERVED
POWER UP MODE
(sum)
ON
OFF
128
64
32
16
8
4
2
1
1
2
3
4
2
1
PLAYING
StdBY
01
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
OFF ON
StdBY
MAIN POWER
PROCESSOR CYCLES
2
I
C SHORTED
BLOCK MATCH
ERROR
RCU
RCVDS
PC
PAUSE
5975198 RETRODATA 808s 210397
3
4-1
Loading...