Barco R9001769, R9001760 User Manual

Download

Page 1

BARCO PROJECTION SYSTEMS

Date : 04122000

REALITY

6400

R9001760 R9001769

OWNER'S MANUAL

Rev. : 03

Art. No. :

R5976069

Page 2

Federal communication commission (FCC statement)

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Instructions to the user :

if this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the following measures :

- Re-orientation of the receiving antenna for the radio or television.

- Relocate the equipment with respect to the receiver.

- Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.  Fasten cables connectors to the equipment by mounting screws.

Note :

The use of shielded cables is required to comply within the limits of Part15 of FCC rules and EN55022.

Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, January 2000.

BARCO n.v./Projection Systems

Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visite Barco at the web : http://www.barco.com

Printed in Belgium

Page 3

TABLE OF CONTENTS --------------------------------------------------- I-1

UNPACKING AND DIMENSIONS -------------------------------------- 1-1

Projector dimensions ------------------------------------------------- 1-1 Unpacking --------------------------------------------------------------- 1-1 Battery installation in the RCU. ------------------------------------ 1-2

INSTALLATION GUIDELINES ------------------------------------------ 2-1

Installation Guidelines ------------------------------------------------ 2-1 Environment ------------------------------------------------------------ 2-1 Environment condition check -------------------------------------- 2-1 What about ambient light ? ----------------------------------------- 2-1 Which screen type? --------------------------------------------------- 2-2 What image size? How big should the image be? ---------- 2-2 Where to install the projector? ------------------------------------- 2-2 How to install a projection lens? ---------------------------------- 2-3

LOCATION AND FUNCTIONS OF CONTROL --------------------- 3-1

Front Panel Terminology -------------------------------------------- 3-1 Source & Power Connections --------------------------------------3-1 Communication Connections -------------------------------------- 3-2 Control Panel Terminology------------------------------------------ 3-2 a. Local keypad -------------------------------------------------------- 3-2 b. Remote control -----------------------------------------------------3-3

INSTALLATION SET UP ------------------------------------------------- 4-1

Configuration ----------------------------------------------------------- 4-1

CONNECTIONS ------------------------------------------------------------- 5-1

Power connection ----------------------------------------------------- 5-1 AC Power (mains) cord connection ------------------------------ 5-1 Fuses --------------------------------------------------------------------- 5-1 Switching on ------------------------------------------------------------ 5-1 Lamp Run Time -------------------------------------------------------- 5-2 Lamp Run Time Warning ------------------------------------------- 5-2 Switching to Stand-by. ----------------------------------------------- 5-2 Switching Off ----------------------------------------------------------- 5-2 Input Connections -----------------------------------------------------5-2 5-cable Input Slot (slot 1) ------------------------------------------- 5-3 Computer input/Monitor output ------------------------------------ 5-4 Video Input -------------------------------------------------------------- 5-4 S-Video Input ----------------------------------------------------------- 5-5 Serial Digital Input / Serial Digital Output ----------------------- 5-5 IEEE 1394 Input ------------------------------------------------------- 5-6 Communication Connections -------------------------------------- 5-6 RS232 in / RS232 out ------------------------------------------------ 5-6 Communication port for communication with peripherals -- 5-7 Audio Connections ----------------------------------------------------5-7

CONTROLLING ------------------------------------------------------------- 6-1

How to use the RCU? ------------------------------------------------ 6-1 Projector address ----------------------------------------------------- 6-2 Displaying a Projector Address. ----------------------------------- 6-2 How to Program an Address into the RCU? ------------------- 6-2 Picture controls with direct access. ------------------------------6-2 Sound controls with direct access. ------------------------------- 6-3 The Pause key. -------------------------------------------------------- 6-3 The Selection key ----------------------------------------------------- 6-3

START UP OF THE ADJUSTMENT MODE ------------------------- 7-1

Adjustment Mode ------------------------------------------------------7-1

Color Temperature ---------------------------------------------------- 9-7 Gamma ------------------------------------------------------------------ 9-7 Decoding EBU/IRE ---------------------------------------------------- 9-7 Dynamic Color Depth ------------------------------------------------- 9-8 Noise Reduction ------------------------------------------------------- 9-8 Input Balance -----------------------------------------------------------9-8 Audio Tuning ----------------------------------------------------------- 9-9 Volume, Balance, Bass and Treble ------------------------------ 9-9 Mute ----------------------------------------------------------------------- 9-9 Fade ---------------------------------------------------------------------- 9-9 Mode [stereo]/[mono] ---------------------------------------------- 9-10 Video - Audio lock --------------------------------------------------- 9-10 Geometry -------------------------------------------------------------- 9-10 Shift --------------------------------------------------------------------- 9-11 Size --------------------------------------------------------------------- 9-11 Side Keystone -------------------------------------------------------- 9-11 Blanking ---------------------------------------------------------------- 9-12 Aspect Ratio ---------------------------------------------------------- 9-13 Options ----------------------------------------------------------------- 9-13

INSTALLATION MODE ------------------------------------------------- 10-1

Starting up the Installation Mode -------------------------------- 10-1 Input Slots ------------------------------------------------------------- 10-1 800 Peripherals ------------------------------------------------------ 10-2 Configuration --------------------------------------------------------- 10-2 OSD color (On-Screen Display) --------------------------------- 10-2 Internal Patterns ----------------------------------------------------- 10-3 No Signal -------------------------------------------------------------- 10-3 Lens Adjustments --------------------------------------------------- 10-3 Zoom/Focus/Shift --------------------------------------------------- 10-4

SERVICE MODE ---------------------------------------------------------- 11-1

Starting up the Service Mode ------------------------------------ 11-1 Identification ---------------------------------------------------------- 11-2 Change Password -------------------------------------------------- 11-3 How to enable or disable the password function ? --------- 11-3 How to change the password ? --------------------------------- 11-3 Change Language -------------------------------------------------- 11-3 Change Projector Address ---------------------------------------- 11-3 Change Baudrate PC ----------------------------------------------- 11-4 Reset Lamp Runtime ----------------------------------------------- 11-4 Lamp Run Time History ------------------------------------------- 11-4 Lamp Dimming ------------------------------------------------------- 11-4 Common Address --------------------------------------------------- 11-4 BARCO logo ---------------------------------------------------------- 11-4 Panel Adjustments -------------------------------------------------- 11-5 Uniformity -------------------------------------------------------------- 11-6 Preset Input Balance ----------------------------------------------- 11-6 I2C diagnosis. -------------------------------------------------------- 11-6

APPENDIX A : STANDARD SOURCE SET UP FILES ---------- A-1

APPENDIX B : LENSES ------------------------------------------------- B-2

Lens Cleaning Procedure ------------------------------------------ B-1 Lenses ------------------------------------------------------------------ B-2

APPENDIX C : SOURCE NUMBERS 81 - 86 AND 91 - 96 ----- C-1

Projector without any 800 peripheral connected. ------------ C-1 Projector with a 800 peripheral connected. ------------------- C-1

AUTO IMAGE ADJUSTMENT ------------------------------------------- 8-1

RANDOM ACCESS ADJUSTMENT MODE ------------------------- 9-1

Starting up the Random Access Adjustment Mode ---------- 9-1 File Service ------------------------------------------------------------- 9-2 Load File -----------------------------------------------------------------9-2 Edit File ------------------------------------------------------------------ 9-3 Rename ------------------------------------------------------------------9-5 Copy ---------------------------------------------------------------------- 9-5 Delete --------------------------------------------------------------------- 9-5 File Options ------------------------------------------------------------- 9-6 Picture Tuning ---------------------------------------------------------- 9-6 CTI ON/OFF ------------------------------------------------------------ 9-6

i-1

5976069 BARCOREALITY 6400 04122000

Page 4

Unpacking and Dimensions

234

379

UNP ACKING AND DIMENSIONS

Unpacking

To open the banding, pull on the clip as shown in the first drawing.

Pull

Take the projector out of its shipping carton and place it on a table.

Save the original shipping carton and packing material, they will be necessary if you ever have to ship your projector. For maximum protection, repack your projector as it was originally packed at the factory.

Contents of the complete unit (box) :

- 1 BARCOREALITY 6400 or 6400DLC (weight ± 17 kg or ± 37.4 lbs)

- 1 remote control unit RCU + 2 batteries.

- 1 power cable with outlet plug type CEE7 or ANSI 73.11 .

- 1 owners manual

- 1 safety manual

o open

Projector dimensions

(units : mm)

25.4 mm = 1"

82.7 211.4 169.5

124.1

184.4

148.9

526.8

380.6

139.6 14

124.4

368.7

371.2

152.6

202.4

187.2

53.5 29.6

107.5

152.6

53.5

120.2

245.1

217.2

147.8

97.6

min 12

max 24

5976069 BARCOREALITY 6400 14032000

1-1

Page 5

Unpacking and Dimensions

Battery installation in the RCU.

Two batteries are packed together with the RCU. Before using your RCU, install first these batteries.

1 Remove the battery cover on the backside by pushing the handle a little towards the bottom of the RCU. 2 Lift up the top side of the cover at the same time. 3 Insert the batteries as indicated in the RCU. 4 Put the battery cover on its place.

How to replace the batteries in the RCU ?

To replace the batteries :

1 Remove the battery cover on the backside by pushing the handle a little towards the bottom of the RCU. 2 Lift up the top side of the cover at the same time. 3 Push on the + side of the battery towards the - side 4 Lift up the battery at the same time. 5 Repeat for the second battery. 6 Insert the batteries as indicated in the RCU (battery type AA or LR6 or equivalent). 7 Put the battery cover on its place.

Note, only important if more than one projector is installed in the room :

1. the common address can be zero (0) or one (1). The standard RCU are setup for common address zero. To change the common address of the RCU, contact a BARCO service center. If it is necessary to program the projector address into the RCU, see chapter 'Controlling'.

2. projector address has to be reprogrammed everytime the battery is changed, the RCU will always switch to the default address.

1-2

5976069 BARCOREALITY 6400 14032000

Page 6

Installation Guidelines

INSTALLATION GUIDELINES

Installation Guidelines

Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system.

Max. ambient temperature : 40 °C or 104 °F Min. ambient temperature : 0 °C or 32 °F The projector will not operate if ambient air temperature falls outside this range (0°C- 40°C or 32°F-104°F).

* Environment

Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not excessive.

* Environment condition check

Warning: Harmful Environmental Contamination Precaution

A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors ventilation inlets. For installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines or similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading performance), then it is highly advisable and desirable to have this contamination removed prior to it reaching the projectors clean air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not a feasible solution then measures to relocate the projector to a clean air environment should be considered.

Only ever use the manufactures recommended cleaning kit which has been specifically designed for cleaning optical parts, never use industrial strength cleaners on a projectors optics as these will degrade optical coatings and damage sensitive optoelectronic components. Failure to take suitable precautions to protect the projector from the effects of persistant and prolonged air contaminants will culminate in extensive and irreversible ingrained optical damage. At this stage cleaning of the internal optical units will be non-effective and impracticable. Damage of this nature is under no circumstances covered under the manufactures warranty and may deem the warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any repair. It is the clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne particles in the environment of the projector. The manufacture reserves the right to refuse repair if a projector has been subject to wantful neglect, abandon or improper use.

* What about ambient light ?

The ambient light level of any room is made up of direct or indirect sunlight and the light fixtures in the room. The amount of ambient light will determine how bright the image will appear. So, avoid direct light on the screen. Windows that face the screen should be covered by opaque drapery while the set is being viewed. It is desirable to install the projection system in a room whose walls and floor are of non-reflecting material. The use of recessed ceiling lights and a method of dimming those lights to an acceptable level is also important. Too much ambient light will wash out of the projected image. This appears as less contrast between the darkest and lightest parts of the image. With bigger screens, the wash out becomes more important. As a general rule, darken the room to the point where there is just sufficient light to read or write comfortably. Spot lighting is desirable for illuminating small areas so that interference with the screen is minimal.

5976069 BARCOREALITY 6400 04122000

2-1

Page 7

Installation Guidelines

* Which screen type?

There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection applications.

Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a determined amount of light projected toward them. The GAIN of a screen is the term used. Front and rear screens are both rated in terms of gain. The gain of screens range from a white matte screen with a gain of 1 (x1) to a brushed aluminized screen with a gain of 10 (x10) or more. The choice between higher and lower gain screens is largely a matter of personal preference and another consideration called the Viewing angle. In considering the type of screen to choose, determine where the viewers will be located and go for the highest gain screen possible. A high gain screen will provide a brighter picture but reduce the viewing angle.

For more information about screens, contact your local screen supplier.

* What image size? How big should the image be?

The projector is designed for projecting an image size (video) from

1.00m (3.3ft) to 6.00m (19.7ft) with a aspect ratio of 5 to 4.

Screen width

* Where to install the projector?

Only when the lens shift is in it's nominal position.

Definitions of the Abbreviation on drawings

B = Distance between ceiling and top of the screen or between floor and bottom of the screen.

A = Correction value, distance between bottom side of projector (without feet) and middle of the lens. Value to be subtracted from B to obtain the correct installation position. (A value is a constant value for all screen widths and type of lenses, A = 124.1 mm or 4.89 inch)

CD = Total distance between projector and ceiling or projector and floor.

SW = Screen width.

SH = Screen height (image height).

PD = Projector Distance, distance between screen and projector.

Inputs and computer video format input compatibility :

Some examples :

VIDEO and S-VIDEO COMPONENT VIDEO RGB ANALOG with STANDARD SYNC (SYNC ON GREEN or

SEPARATE SYNC) RGB ANALOG with TRI-LEVEL SYNC (SYNC ON GREEN or SEPARATE SYNC) VGA : 640 x 480 pixels MAC : 640 x 480 pixels Super VGA : 800 x 600 pixels XGA : 1024 x 768 pixels S-XGA : 1280 x 1024 pixels sources up to 1600 x 1280 pixels Sources with pixel clock < 200 MHz

Lens type selection.

a) Determine the required screen width.

b) Determine the approximate position of the projector in the projection

room with regard to the screen and measure the

projector-screen distance (PD).

c) Use the lens formulas in appendix B to find the best corresponding

PD with regard to the measured projector-screen distance for the

required screen width. The desired lens is determined (the order number is given in the tabel in the same appendix B). Start the installation procedure for the projector as described in the manual.

2-2

5976069 BARCOREALITY 6400 04122000

Page 8

Installation Guidelines

Screen

Floor

Projector

A’

Optical axis projection lens

SIDE VIEW

BACK VIEW

Screen

TOP VIEW

Floor

OFF-Axis installation

Screen

Optical axis projection lens

SIDE VIEW

Floor

TOP VIEW

BACK VIEW

ON-Axis installation

D = B - A

CD = B - A

Projector

Floor

* How to install a projection lens?

The projector is supplied without any lens. The following lenses are available, or will become available (contact a Barco service center) as an option :

QFD(1.27:1) R9840400 QFD(2.5:1) R9840290 QFD(1.4-2.1:1) R9840380 QFD(2.1-3.0:1) R9840390 QGD(3.5-4.5:1) R9840060 QFD(4.5-6.0:1) R9840100 QFD(7:1) R9840410

5976069 BARCOREALITY 6400 04122000

2-3

Page 9

Installation Guidelines

How to install the lens?

1. Take the lens out of its packing material.

2. Open the lens cover of the projector by pivoting it up and take it off. image 1

3. Open both lens locks (B) by pulling them backwards. Unlock first by pulling clip (A) forwards. image 2

4. Put the lens on the lens holder.

5. Fix the lens by closing both locks (B) until they are secured. image 3

6. Plug the wires of motor unit into the connector (C). image 3

7. Re-install the lens cover.

Image 1

Image 3

Image 2

Image 4

2-4

5976069 BARCOREALITY 6400 04122000

Page 10

Location and Functions of Control

LOCATION AND FUNCTIONS OF CONTROL

Front Panel Terminology

The front panel terminology can be divided into 'Source & power connections' and 'Communication connections'.

Source & Power Connections

VIDEO

GBH/CV

S-VIDEO

IEEE 1394

SDI

SDO

COMPUTER

TRIG

MONITOR

RS232 IN RS232 OUT

MOUSE

AUDIO IN AUDIO IN AUDIO IN

COMM. PORT

AUDIO OUT

1 Video input: 1cinch or 1 BNC connector, no loop through.

2 Power switch : '1' = on, '0' = off

3 Power input : autoranging from 90 to 240 Vac.

4 S-Video

5 SDI and SDO : serial digital input and loop trough output. 2 x BNC terminals.

6 IEEE 1394 : not yet implemented.

7 5-cable input : can be software switched between Video, S-Video, RGB analog or Component Video.

8 Computer input

9 Monitor output : the monitor of your computer can be connected to this output if your computer is connected to the computer

input.

10 Audio inputs : 3 audio inputs. Each audio input can be associated with arbitrary input.

11 Audio output

5976069 BARCOREALITY 6400 21082000

3-1

Page 11

Location and Functions of Control

Communication Connections

VIDEO

S-VIDEO

12 3 456

SDI

SDO

IEEE 1394

TRIG

RS232 IN RS2 32 OUT

MOUSE

COMM. PORT

GBH/CV

MONITOR

COMPUTER

AUDIO IN AUDIO IN AUDIO IN

AUDIO OUT

1 TRIG : output voltage of 5 V when projector is on.

2 MOUSE : mouse output to be connect to the mouse input of a computer. The computer can now be controlled via the Executive

Remote Control Unit.

3 RS232 IN : to allow communication with external computer, e.g. IBM PC or compatible, Macintosh ...

4 RS232 OUT : used to connect to next projector, RS232IN plug (communication link for PC or MAC to the next projector).

5 Communication port : allows communication with the 800 peripherals.

6 IR-Acknowledged : IR signals are recognized.

IR-Received : IR signals are received but not recognized by the projector.

7 Projector mode indication : indicates the status of the projector.

Light off : power switch is not pressed. Red light : power switch is pressed, projector in stand by mode. Green light : projector in operational mode.

8 Diagnostics code :

a) source number b) error code : a two digit error code is displayed when something goes wrong inside the projector.

9 Remote : remote input for wired remote control.

10 IR receiver : receiver for control signals transmitted from the RCU.

Control Panel Terminology

The projector can be controlled by the local keypad or by the remote control unit.

a. Local keypad

The local keypad is located on the backside of the projector.

3-2

5976069 BARCOREALITY 6400 21082000

Page 12

ADJ

EXIT

ENTER

PAUSE

PHASE

TEXT

SHARPN

TINT

COLOR

BRIGHTN

CONTR

TREBLE BALANCE

BASS

VOL

5 6

7 8

17 16

15 14 13

b. Remote control

This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set up. It includes automatic storing of :

- picture controls (Brightness, Sharpness...)

- settings

Other functions of the remote control are :

- switching between standby and operational mode.

- switching to "pause" (blanked picture, full power for immediate restarting)

- direct access to all connected sources.

Location and Functions of Control

Remote Control (RCU)

9 7 5 3 1

STANDBY

8 6 4 2

TEXT

SHARPN

PHASE

ENTER

COLOR

TINT

EXIT

PAUSE

BRIGHTN

CONTRAST

17 15

14 11

Local keypad

Terminology

1 Function keys : user programmable keys with functions for direct access.

2 ADJ. : to escape the adjustment mode.

3Address key (recessed key), to enter the address of the projector (between 0 and 9). Press the recessed address key with

a pencil, followed by pressing one digit button between 0 and 9.

4 Selection key : to direct access the zoom/focus/shift functions.

5 PAUSE : to stop projection for a short time, press 'PAUSE'. The image disappears but full power is retained for immediate restarting.

6 STBY : stand-by button, to start projector when the power switch is switched on and to switch off the projector without switching

off the power switch.

Attention : Switching to Stand-by.

When the projector is running and you want to go to stand-by, press the stand-by key for 2 seconds until the message 'Saving data, please wait' is displayed. Do not press any longer on the stand-by key otherwise the projector will restart.

7 Mute : to interrupt the sound reproduction.

8? : Auto image, to center the image on the active LCD surface.

9 Digit buttons : direct input selection.

10 Audio controls : use these buttons to obtain the desired sound level (see also 'Controlling').

11 Picture controls : use these buttons to obtain the desired picture analog level (see also 'Controlling').

12 PHASE : used to remove the instability of the image.

5976069 BARCOREALITY 6400 21082000

3-3

Page 13

Location and Functions of Control

13 FREEZ : press to freeze the projected image.

14 TEXT : when adjusting one of the image, e.g. controls during a meeting, the displayed bar scale can be removed by pressing

'TEXT' key first. To re-display the bar scale on the screen, press 'TEXT' key again.

15 ENTER : to start up the adjustment mode or to confirm an adjustment or selection in the adjustment mode.

16 Cursor Keys (on RCU) or '+' and '-' keys (cursor keys) on the local keypad : to make menu selections when in the adjustment

mode or to zoom/focus when the direct access is active.

Comparision between the cursor keys and the use of the '+' and '-' keys on the local keypad : RCU = local keypad cursor key up = '+' key up cursor key down = '-' key down cursor key right = '+' key right cursor key left = '-' key left

Use the '+' and '-' keys (cursor keys) : to increase or decrease the analog level of the image controls when they are first selected.

17 EXIT : to leave the adjustment mode or to scroll upwards when in the adjustment mode.

18 RC operating indication : lights up when a button on the remote control is pressed. (This is a visual indicator to check the

operation of the remote control)

3-4

5976069 BARCOREALITY 6400 21082000

Page 14

Installation Set Up

INSTALLATION SET UP

Configuration

The projector can be installed to project images in four different configurations : front/table, front/ceiling, rear/table and rear/ceiling.

Rear/Ceiling

Front/Ceiling

Rear/Table

Changing the configuration :

Front/Table

To change the configuration of the projector, proceed as follow :

1 Press ENTER to start up the adjustment mode. 2 Press the cursor key é or ê to select 'Installation'. 3 Press ENTER to display the Installation menu. 4 Press the cursor key é or ê to select 'Configuration'. 5 Press ENTER to display the Configuration menu. The actual installed configuration will be highlighted. 6 Press the cursor key é or ê to select the corresponding configuration. 7 Press Adjust to leave the adjustment mode.

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

Select with or

then <ENTER>

<EXIT> to return.

INSTALLATION

INPUT SLOTS

800 PERIPHERAL

CONFIGURATION

OSD COLOR

INTERNAL PATTERNS

NO SIGNAL

Select with or

then <ENTER>

<EXIT> to return.

LENS

CONFIGURATION

FRONT/TABLE

FRONT/CEILING

REAR/TABLE

REAR/CEILING

5976069 BARCOREALITY 6400 21082000

Select with or

then <ENTER>

<EXIT> to return.

4-1

Page 15

Connections

CONNECTIONS

Power connection

AC Power (mains) cord connection

Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the front of the projector.

The power input is auto-ranging from 90 to 240 VAC.

S-VIDEO

VIDEO

GBH/CV

SDI

TRIG

IEEE 1394

SDO

COMPUTER

RS232 IN RS232 OUT

MOUSE

MONITOR

AUDIO IN AUDIO IN AUDIO IN AUDIO IN

COMM. PORT

Fuses

Warning For continued protection against fire hazard :

- refer replacement to qualified service personnel

- ask to replace with the same type of fuse. Fuse type : T10 AH/250V

Switching on

Use the power switch to switch on.

When '0' is visible, the projector is switched off.

When '1' is visible, the projector is switched on. When switching on with the power switch, the projector starts in the stand by mode. The projector mode indication lamp is red.

To start image projection : a. press the 'Stand by' button once on the local keypad or on the remote control. The projector mode indication lamp will be green. b. press a digit button to select an input source. The projector mode indication lamp will be green.

100-240 V

VIDEO

S-VIDEO

SDI

Stand-by key

9 7 5 3 1

STANDBY

8 6

TEXT

SHARPN TINT BRIGHTN

ENTER

COLORPHASE

EXIT

PAUSE

CONTRAST

6-2.5 A 50-60 Hz

ADJ

PAUSE

TREBLE B ALANCE

BASS

EXIT

ENTER

TEXT

PHASE

SHARPN

TINT

COLOR

BRIGHTN

CONTR

VOL

5-1

Projector mode indication

5976069 BARCOREALITY 6400 14032000

Page 16

Lamp Run Time

When the total run time of the lamp is X-30 hours or more, the following warning message will be displayed for 1 minute. This warning message will be repeated every 30 minutes. Press EXIT to remove the message before the minute is over. When the total run time of the lamp is 500 hours or more, the following warning message, with the exact run time is displayed on the screen.

Connections

Lamp run time is X hours. Operating the lamp longer than X hours may damage the projector. Please replace the lamp.

Remaining Lamp run time 20 h

When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min.

The total lifetime of the lamp for a safe operation is X hours max. Do not use it longer. Always

WARNING

replace with a same type of lamp. Call a BARCO authorized service technician for lamp replacement.

Lamp Run Time Warning

Using a lamp for more than X hours is dangerous as the lamp could

Lamp run time is X hours

Operating the lamp longer

than X hours may damage

the projector.

Please replace the lamp

<ENTER> to continue

explode.

Switching to Stand-by.

Switching Off

To switch off:

- First press STANDBY key for 2 seconds. When the message 'Saving data, please wait' is displayed, do not press any longer on the standby key otherwise the projector will restart. Let cool down the projector at least 10 min.

- Switch off the projector with the power switch.

Switching to Stand-by Warning When switching to standby, it is possible to restart within the first 5sec.. When not restarted within these first 5 sec., the projector waits for 1 min. to restart again. During this period the LED display will show a jumping square with a dash. After one minute, two dashes will be displayed and the projector can restart.

Saving data, Please wait

Input Connections

Input facilities : Video

Input Selection : This can be manually or automatically. When 'automatic' is selected in the Input slots menu, by starting up the projector, it searches for an input source by scanning the inputs one by one. If only one source is found, this source will be projected. If different sources are found, the priority is as follow :

1. Video

2. S-Video

3. 5 Cable input

4. Computer input

SDI input and IEEE input are never automatically selected.

Note : When a RCVDS is connected to the projector, the 'Automatic' selection is disabled.

Set up of the input selection :

1 Press ENTER to start up the adjustment mode. 2 Press the cursor key é or ê to select 'Installation'. 3 Press ENTER to display the Installation menu. 4 Press the cursor key é or ê to select 'Input Slots'. 5 Press ENTER to display the Input slots menu. 6 Press the cursor key é or ê to select 'Input Slots'. 7 Press ENTER to toggle between [Manual] or [Automatic]. 8 Press EXIT several times to leave the adjustment mode.

S-Video 5-cable input Computer Serial digital input IEEE 1394 (not yet active)

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

Select with or

then <ENTER>

<EXIT> to return.

INSTALLATION

INPUT SLOTS

Select with or

then <ENTER>

<EXIT> to return.

INPUT SLOTS

SLOT SELECTOR [Automatic]

x 1. RGB [HS&VS]

- 2. RGB [HS&VS] x3. VIDEO

- 4. S-VIDEO

- 5. DIGITAL INPUT

- 6. IEEE 1394 Select with or

<ENTER> to toggle

<EXIT> to return.

5976069 BARCOREALITY 6400 14032000

5-2

Page 17

Connections

Use of a RCVDS05 or VS05 : When using a RCVDS05, it is recommended to use a 5-cable output module in the RCVDS. The outputs of this module have to be connected to the 5 cable input (slot 1) of the projector. To switch the projector in the 5-cable mode see chapter 'Installation mode'.

5-cable Input Slot (slot 1)

Slot 1 has 5 BNC input terminals. The following signals can be connected to these BNC connectors :

Connector name R G B H V

Input signal

RGBHV R G B H V

RGBS R G B S -

RGsB R Gs B - -

Composite Video - Video - - -

Super Video - Y - - C

Component Video - SS R-Y Y B-Y S -

Component Video - SOY R-Y Ys B -Y - -

Slot 1 selection :

Key in 1 on the RCU or the local keypad.

Configuration of the 5-cable input :

The configuration has to be done on the 'Input slot' menu.

To change the signal format :

1 Press ADJUST or ENTER key to start up the Adjustment

mode.

2 Push the cursor key é or ê to select Installation 3 Press ENTER. 4 Press the cursor key é or ê to select 'Input Slots' 5 Press ENTER. The internal system will scan the inputs and

displays the result in the 'Input Slots' menu.

6 Push the cursor key é or ê to select the first slot. 7 Press ENTER key to toggle the input signal priority.

Possible indication :

RGB [HS&VS] = RGB analog signals, separate sync

is horizontal and vertical sync.

RGB CS = RGB analog signals, separate sync is composite sync. RGB CV = RGB analog signals, separate sync is composite video

or tri-level sync.

RGB-SOG = RGB analog signals, sync on green is composite sync. COMPONENT VIDEO - CS = separate sync is composite sync. COMPONENT VIDEO = component video with composite sync on

Y or composite tri-level sync on Y.

VIDEO S-VIDEO

VIDEO

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

Select with or

then <ENTER>

<EXIT> to return.

S-VIDEO

GB H/CV

SERVICE

SDI

SDO

INSTALLATION

INPUT SLOTS

800 PERIPHIRAL CONFIGURATION

OSD COLOR

INPUT SLOTS

SLOT SELECTOR [Automatic]

x 1. RGB [HS&VS]

- 2. RGB [HS&VS] x3. VIDEO

- 4. S-VIDEO

- 5. DIGITAL INPUT

- 6. IEEE 1394 Select with or

<ENTER> to toggle

<EXIT> to return.

IEEE 1394

COMPUTER

TRIG

MONITOR

When using an RCVDS 05 with a 5 cable output module, connect these 5 cables to this 5-cable input slot (slot1) of the projector. All sources of the RCVDS can now be accepted by the projector.

Audio connection : Connect the audio input to one of the 3 audio inputs. See 'audio configuration' in this chapter for more explanation.

5-3

5976069 BARCOREALITY 6400 14032000

Page 18

Connections

Computer input/Monitor output

Connect the output of the graphical card of the computer to the Computer input of the projector (connection < 60 cm) or insert an interface between the output of the computer and the input of the projector.

Connect the monitor of the computer to the monitor output of the projector. This monitor output is only available when the computer input is used as input.

VIDEO

S-VIDEO

SDI

SDO

IEEE 1394

TRIG

RS232 IN RS232 OUT

MOUSE

COMM. PORT

GBH/CV

Pin configuration of the D15 connector :

1 RED 2 GREEN 3 BLUE 4 loop through to monitor 5 ground 6 ground 7 ground

9 loop through to monitor 10 ground 11 loop through to monitor 12 loop through to monitor 13 horizontal/composite sync 14 vertical sync 15 loop through to monitor

8 ground

Slot 2 selection :

Key in 2 on the RCU or the local keypad.

Video Input

Input signal :

Composite video signals from a VCR, OFF air signal decoder, etc... 1 x BNC or cinch 1.0Vpp ± 3 dB No loop through.

MONITOR

AUDIO IN AUDIO IN AUDIO IN

COMPUTER

AUDIO IN

Slot 3 Selection :

Key in 3 on the RCU or the local keypad.

5976069 BARCOREALITY 6400 14032000

S-VIDEO

VIDEO

RGBH/CV

SDI

SDO

Composite

Video

TV tuner, e.g. Marco Polo

TRIG

IEEE 1394

MONITOR

COMPUTER

RS232 IN RS232 OUT

MOUSE

AUDIO IN AUDIO IN AUDIO IN AUDIO IN

COMM. PORT

A, B or C

VCR

5-4

Page 19

Connections

SDI

SDO

S-VIDEO

VIDEO

COMPUTER

IEEE 1394

TRIG

MOUSE

MONITOR

RS232 IN RS232 OUT

AUDIO IN AUDIO IN AUDIO IN

AUDIO IN

COMM. PORT

GBH/CV

VCR S-VHS

Luma/Chroma

A, B or C

SDI

SDO

S-VIDEO

VIDEO

COMPUTER

IEEE 1394

TRIG

MOUSE

MONITOR

RS232 IN RS232 OUT

AUDIO IN AUDIO IN AUDIO IN

AUDIO IN

COMM. PORT

GBH/CV

DIGITAL VIDEO SOURCE

Digital Video

S-Video Input

Input signal :

Separate Y-luma/C-chroma signals for higher quality playback of Super VHS-signals.

Pin configuration mini DIN plug :

1 ground luminance 2 ground chrominance 3 luminance 1.0Vpp ± 3 dB 4 chrominance 282 mVpp ± 3 dB

Slot 4 Selection :

Key in 4 on the RCU or the local keypad.

Serial Digital Input / Serial Digital Output

Standard for the BarcoReality 6400DLC. Optional for the BarcoReality 6400.

Full compatibility with digital Betacam, or digital video sources. This avoids the need for analog processing anywhere in the video production chain and guarantees the ultimate image quality.

An active loop through of the SDI input signal is provided for monitoring or for double or triple stacking applications.

5-5

5976069 BARCOREALITY 6400 14032000

Page 20

connections :

1 x BNC input and 1 x BNC output.

The input is always 75 Ω terminated. The output impedance of the SDO is 75 Ω.

Slot 5 Selection :

Key in 5 on the RCU or the local keypad.

Note : When a RCVDS05 is connected to the projector, the SDI input is available by keying in 85 on the RCU.

IEEE 1394 Input

Input not yet implemented.

Communication Connections

The following communication connections are available :

RS232 in / RS232 out. Comm port for communication with peripheral (switchable between PPM and RC5) RC for remote cable connection with the RCU. MOUSE to control a PC with the projector remote control. TRIG : output voltage to control another device.

RS232 in / RS232 out

Connections

To connect a Computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS 232 input of the projector to allow communicate between the computer and the projector.

VIDEO

S-VIDEO

GBH/CV

SDI

SDO

IEEE 1394

COMPUTER

TRIG

MONITOR

RS232 IN RS232 OUT

MOUSE

AUDIO IN AUDIO IN AUDIO IN

COMM. PORT

AUDIO IN

RS232 connection

Applications :

a) remote control :

- easy adjustment of projector via IBM PC (or compatible) or MAC connection.

- allow storage of multiple projector configurations and set ups.

- wide range of control possibilities.

- address range from 0 to 255.

b) data communications :

- sending data to the projector or copying the data from the projector to a hard memory device (hard disc, floppy, etc.).

Set up of the Baud Rate for Communication with a Computer :

See 'Change Baudrate PC' in chapter 'Service mode'.

5976069 BARCOREALITY 6400 14032000

5-6

Page 21

Connections

Communication port for communication with peripherals

This port can be configured to accept PPM or RC5 coded signals. To change the port configuration see 800 Peripherals in Chapter Installation.

Connecting a RCVDS 05 to the projector.

- Up to 20 inputs with the RCVDS 05 and 90 inputs when RCVDS's are linked via the expansion module.

- Serial communication with the projector.

- Remote control buttons on the RCVDS to control the projector (source selection and analog settings).

- The selected source number will be displayed on a 2 digit display and the selected input module will be indicated with a LED on the rear.

For more information about the use of the RCVDS 05, consult the owner's manual of the RCVDS05, order number : R5975765.

Connecting a VS05 to the projector

The VS05 can switch up to 5 Composite Video sources, 3 Super Video sources and 1 RGB analog or component video source to the projector. In addition, the audio signal proper to the source, can be switched to an audio amplifier or the audio input of the projector. Order number : R9827890

For more information about the use of the VS05, consult the VS05 owner's manual, order number : R5975245.

TRIG Output

5 V output voltage to trigger an external device (max. 10mA). This voltage is available when the projector is on.

MOUSE

Mouse function is only available with the Executive Remote Control (Order number : R9829960). The computer can then be controlled via the projector. To activate this mouse function, handle as follow :

1 Start up your computer with the computer mouse plugged in. The mouse driver should be loaded. 2 Unplug the computer mouse without switching off the computer. 3 Plug the delivered cable between the mouse input of the computer and the mouse output of the projector. 4 Computer can now be controlled with the executive remote control. For more information about the mouse buttons or functions, consult the owner's manual of the Executive Remote Control.

Warning : before swithing off, disconnect first the mouse cable.

Mouse functions : Left click, right click or double click are the same as for a traditional mouse. For Click and drag : push for 2 seconds on the left (right) mouse button, the move the mouse arrow with the mouse navigator and click again very short on the left (right) mouse button to interrupt the drag function.

Audio Connections

Three audio inputs and one audio output are available. Each audio input can be associated with an input source using the control software of the projector. e.g. source 1 can be locked with audio input B.

Locking an audio input to a source input :

1 Press ENTER to start up the adjustment mode. 2 Press the cursor key é or ê to select 'Random Access'. 3 Press ENTER to display the Random Access menu. 4 Press the cursor key é or ê to select 'Audio Tuning'. 5 Press ENTER to display the Audio Tuning menu. 6 Press the cursor key é or ê to select 'Video-Audio lock'. 7 Press the cursor key ç or è to select the desired source input. 8 Press ENTER to toggle between [A], [B] or [C]. 9 Press several times EXIT or ADJUST to return to the operational mode.

See also 'Video - Audio lock' in chapter 'Random Access Adjustment Mode'.

5-7

5976069 BARCOREALITY 6400 14032000

Page 22

Controlling

SDI SDOS-VIDEOVIDEO

COMPUTER

IEEE 1394

TRIG

MOUSE

MONITOR

RS232 IN RS232 OUT

AUDIO IN AUDIO IN AUDIO IN AUDIO IN

COMM. PORT

RGBH/C

45° 45°

F2F3F4

ADJ EXIT

ENTER

PAUSE

PHASE

TEXT

SHARPN

TINT

COLOR

BRIGHTN

CONTR

TREBLE BALANCE

BASS VOL

F2F3F4

ADJ EXIT

ENTER

PAUSE

PHASE

TEXT

SHARPN

TINT

COLOR

BRIGHTN

CONTR

TREBLE BALANCE

BASS VOL

CONTROLLING

The projector can be controlled with

a. The RCU b. The hardwired RCU (cable is not included) c. The local keypad.

Controlling the projector with the RCU and the hardwired RCU is equal.

How to use the RCU?

a) Point the front of the RCU to the reflective screen surface.

Screen

Ce il ing

IR s enso r

RCU

b) RCU used in a hardwired configuration.

S-VIDEO

VIDEO

GBH/CV

SDI

IEEE 1394

SDO

COMPUTER

RS232 IN

TRIG

MOUSE

MONITOR

AUDIO IN AUD IO IN AUD IO IN

RS232 OUT

COMM. PORT

AUDIO IN

Plug one end of the remote cable in the connector on the bottom of the RCU and the second side in the connector in the front panel of the projector labelled 'RC'.

c) Point the front of the RCU directly at one of the IR sensors of the projector.

When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line). The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control unit and the projector IR sensor.

5976069 BARCOREALITY 6400 14032000

6-1

Page 23

Controlling

Projector address

a. Software set up of the projector address.

See 'Change projector address' in chapter 'Service mode'.

b. How to control the projector or projectors.

The projector's address may be set to any value between 0 and 255. When the address is set, the projector can be controlled now :

- RCU for addresses between 0 and 9.

- computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255.

Note : a projector will respond to a RCU set to the common address ('0' or '1') regardless of what address is set in the projector itself.

c. Using the RCU.

The RCU is default programmed with address 0 or 1, 'common address'. With that 'common address' programmed into the RCU, every projector, without exception will listen to the commands given by this RCU. If it is necessary to control a specific projector, than enter the projector address into the RCU (only when that address is between 0 and 9). The projector with the corresponding address will listen to that specific RCU.

Common Address

Every projector has a common address '0' or '1'. The choice between '0' and '1' can be selected in the Service mode.

Displaying a Projector Address.

Press the ADDRESS key (recessed key on the RCU) with a pencil. The projector's address will be displayed in a 'Text box'. This text box disappears after a few seconds.

To continue using the RCU with that specific address, it is necessary to enter the same address with the digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the Address key displays projector address 003, then press "3" digit button on the RCU to set the RCU's address to match the projector's address. Do not press 003 digits. This will address the remote control to '0' and control all projectors in the room. If the address is not entered within 5 seconds, the RCU returns to its default address (zero address) and control all projectors in the room.

How to Program an Address into the RCU?

Press the ADDRESS key (recessed key on the RCU) with a pencil and enter the address with the digit buttons within 5 seconds after pushing the address key. That address can be any digit between 0 and 9.

Picture controls with direct access.

When an image control is pressed, a text box with a bar scale, icon and function name of the control, e.g. 'brightness...' appears on the screen (only if text is ON). Se e example screen. The length of the bar scale and the value of the numeric indication indicate the current memorized setting for this source. The bar scale changes as the control stick on the RCU is pressed or the + or - buttons on the local keypad.

Brightness Control

PROJECTOR ADDRESS

001

A correct 'brightness' setting is important for good image reproduction. Use the + button for a higher brightness. Use the - button for a lower brightness.

Contrast Control

A correct 'contrast' setting is important for good image reproduction. Adjust the contrast to the level you prefer, according to room lighting conditions. Use the + button for a higher contrast. Use the - button for lower contrast.

Color Saturation

Color saturation is only active for Video and S-Video. Adjust the color intensity of the picture. Use the + button for richer colors. Use the - button for lighter colors.

6-2

BRIGHTNESS

0 127

5976069 BARCOREALITY 6400 14032000

Page 24

Controlling

Tint Control

Tint is only active for Video and S-Video when using the NTSC 4.43 or NTSC 3.58 system. Use the + button Use the - button.

Sharpness Control.

Use the + button for a sharper picture. Use the - button for a softer picture.

Phase Control

Use the control disc to adjust the phase.

Freez key

Press Freez to freeze the displayed image.

Sound controls with direct access.

When a sound control is pressed, a text box with a bar scale, icon and function name of the control, e.g. 'volume...' appears on the screen (only if text is ON). See example screen. The length of the bar scale indicates the current memorized setting for this source. The bar scale changes as the + or - buttons of the control are pressed. The picture controls can only be adjusted with the RCU.

Volume Control

Volume control adjusts the volume. Use the + button for a higher volume. Use the - button for a lower volume.

Bass Control

Bass control adjusts the bass level (low tones). Use the + button for more low tones. Use the - button for less low tones.

Treble Control

Treble control adjusts the treble level (high tones). Use the + button for more high tones. Use the - button for less hight tones.

Balance Control

Is only effective if a external amplifier with loudspeakers is connected to the audio output. The balance control adjust the sound level between the left and the right box. Use the + button for a higher sound level on the right box than on the left one. Use the - button for a higher sound level on the left box than on the right one.

The Pause key.

When the Pause key is pressed, the image projection is stopped, a blue screen will be displayed and the projector remains with full power for immediate restart. The sound is not interrupted. The display on front of the projector will show a "P". To restart the image :

1 press pause key, 2 press exit key or 3 select a source number.

5976069 BARCOREALITY 6400 14032000

6-3

Page 25

Controlling

The Selection key.

When the Selection key is pressed, the zoom/focus/shift menu will be displayed inmediately. To focus or zoom the image :

1 Push the é or ê key to zoom and ç or è key to focus the image. 2 When finished, press EXIT to return.

To shift the image :

1 Press ENTER to switch to the shift menu 2 Push the é or ê key to shift the image up or down and ç or è key to shift the image

left or right.

3 When finished, press EXIT to return

Zoom/Focus

Change with é,ê,ç,è

<ENTER> to Shift

<EXIT> to return

6-4

5976069 BARCOREALITY 6400 14032000

Page 26

Start up of the Adjustment Mode

START UP OF THE ADJUSTMENT MODE

Adjustment Mode

All source parameters, picture and audio tuning, and geometry are made while in the 'Adjustment Mode'. Press the ADJUST or ENTER key to enter the 'Adjustment mode'.

You are now in the 'Adjustment Mode'.

1 The cursor key (RCU) or '+ or '-' keys (local keypad) are used to make menu selections

and also for adjustments.

2 The ENTER and EXIT keys are used to move forward and backward through the

menu structure.

3 The ADJUST key can be used to terminate the adjustment mode while any path

selection menu is displayed.

There are 4 possible paths to follow once in the Adjustment Mode. They are :

Auto Image - Auto image will center the image on the LCD panel when a file is loaded.

Installation - Installation should be selected if a new input module is installed or a new source is connected to an existing input module. Also

when the projector is relocated in a new configuration.

Random Access - Random Access should be selected to set up a new source.

ADJUSTMENT MODE

Select a path from below :

AUTO IMAGE

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

Select with or

then <ENTER>

<EXIT> to return.

Service - Service should be selected if the user intends to change general settings such as password, language, address, etc.or some service actions as reset lamp run time, panel adjustments, etc. or get set-up information.

Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks to enter your password (Password protection is only available when the password strap on the controller module is ON, call an authorised service center to change the position of the password strap).

Password :

ENTER PASSWORD

Use numeric keys

<EXIT> to return

Error

Invalid password

<EXIT> to return

PASSWORD

----

The password contains 4 digits.

Enter the digits with the numeric keys. Example : 2 3 1 9

The first digit position is highlighted. Enter with the numeric keys. The highlighted square jumps to the next position. Continue until all 4 digits are filled in.

When your password is correct, you gain access to the selected item. When your password is wrong. The error message "Invalid password" is displayed on the screen. Press EXIT to continue and to return to the Service menu.

Factory programmed password : 0 0 0 0

Once the password is correctly entered, all other password protected items are accessible without re-entering the password.

When re-entering the Adjustment mode, it will be nessary to enter the password again when selecting a password protected item.

Setting up your own password :

See 'Changing password' in the Service mode.

5976069 BARCOREALITY 6400 14032000

7-1

Page 27

Auto Image Adjust

AUTO IMAGE ADJUSTMENT

Auto Image Adjustment

Push the cursor key é or ê to highlight 'Auto Image' and press ENTER.

With auto image, it is possible to switch the auto image function 'on' or 'off' and to adjust an existing image when the auto image function is off.

Adjust

By selecting Adjust the image will be centered on the active area of the LCD surface. The centering will be done by adapting the values for 'pixel start', 'pixel end', 'line start' and 'line end'.

To center the image : 1 Push the cursor key é or ê to highlight 'Adjust'. 2 Press ENTER to activate. The image will be centered on the LCD surface.

This is the same function as the '?' key on the remote control when in operational mode. The menu is automatically exited. The adjustment values will be saved when switching to another source.

ADJUSTMENT MODE

Select a path from below :

AUTO IMAGE

RANDOM ACCESS

INSTALLATION

Select with or

then <ENTER>

<EXIT> to return.

ADJUSTMENT MODE

Select a path from below :

AUTO IMAGE

RANDOM ACCESS

INSTALLATION

SERVICE

Select with or

then <ENTER>

<EXIT> to return.

ACTION : FULL AUTOMATIC

SERVICE

Source 01

AUTO IMAGE

ADJUST

Action

The action function can be toggled between :

- full automatic

- on new file

- manual

[full automatic] : the best fitting file will be loaded automatically when a source is selected. At the same time the image will be automatically centered on the active surface of the LCD.

The centering of the image will be disabled when : 1 The black edges of the image take more than 25% of the complete image. 2 The connected source is video, s-video, digital video or HDTV. 3 Custom file already exists.

[on new file] : only on a new file, the image will be centered on the active surface of

the LCD.

[manual] : the auto image function is switched OFF, no centering, no file load.

To setup the Action function : 1 Push the cursor key é or ê to highlight 'ACTION'. 2 Press ENTER to toggle between FULL AUTOMATIC, ON NEW FILE and

MANUAL.

Select with or

then <ENTER>

<EXIT> to return.

The values of automatically adjusted sources will not be saved.

7-1

5976069 BARCOREALITY 6400 21082000

Page 28

Random Access Adjustment Mode

RANDOM ACCESS ADJUSTMENT MODE

Starting up the Random Access Adjustment Mode

Push the cursor key é or ê to highlight 'Random Access' and then press ENTER.

LOAD

EDIT

RENAME

FILE SERVICE

RANDOM ACCESS ADJUSTMENT MODE

COPY

DELETE

OPTIONS

CTI

COLOR TEMPERATURE

GAMMA

ADJUSTMENT MODE

Select a path from below :

AUTO IMAGE

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

Select with or

then <ENTER>

<EXIT> to return.

PICTURE TUNING

AUDIO TUNING

DECODING

DYNAMIC COLOR DEPTH

NOISE REDUCTION

INPUT BALANCE

VOLUME

BALANCE

BASS

TREBLE

MUTE

FADE

MODE STEREO/MONO

VIDEO - AUDIO LOCK

SHIFT

SIZE

GEOMETRY

5976069 BARCOREALITY 6400 14032000

SIDE KEYSTONE

BLANKING

ASPECT RATIO

OPTIONS

8-1

Page 29

Random Access Adjustment Mode

File Service

Before using a new source, a correct file has to be installed. The projector's memory contains a list of files corresponding to the most used sources. When the new source corresponds with one of these files, the file can be loaded and saved for future use. When there is a little difference, the file can also be loaded and then edited until the source specs are reached.

Note : file loading can be done automatically (see File Options, in this

chapter).

Files with a ~ in front of the file name are tempory files. These files

will be deleted when switching to another source.

To enter the File Service, handle as follow :

1 Pushing the cursor key é or ê to highlight 'File Service'. 2 Press ENTER to select.

The File service menu will be displayed.

Note : EXIT returns to the Path selection menu.

ADJUST returns to operational mode.

The following file manipulations are possible :

- Load : installation of a file for a new source.

- Edit : editing a loaded file to the source specs.

- Rename : renaming a file.

- Copy : copying a file to a new file.

- Delete : deleting an existing file.

- Options : way of sorting the files.

File annotation :

xxxxxxxx.xxx x xxxxXxxxxi

i or blank : i = interlaced, blank = not interlaced

xxxxXxxxx : active pixel rating

x : source number

xxx : file extension, first character is C (for custom made files) or S (for standard files). The second and third character is used for a following number (=file index) file index for custom files : 00 to 63.

xxxxxxxx : base name, 8 characters.

RANDOM ACCESS

ADJUSTMENT MODE

FILE SERVICE

PICTURE TUNING

AUDIO TUNING

Select with or

then <ENTER>

<EXIT> to return.

GEOMETRY

FILE SERVICE

LOAD

EDIT

RENAME

COPY

DELETE

OPTIONS

Select with or

then <ENTER>

<EXIT> to return.

Load File

1 Push the cursor key é or ê to highlight 'Load'. 2 Press ENTER to select.

The Load menu displays the corresponding files depending on the installed filter.

This filter can be "Fit" or "All". To change the filter : 1 Push the cursor key è or ç highlight 'filter list'. 2 Press ENTER to toggle the annotation between brackets.

"All" : all files that can be loaded will be displayed. "Fit" : only the best fitting files will be displayed (with a distinction of ± 2 lines and line duration distinction of ± 300 ns, if nothing is found within this small area, the projector continues searching until it finds something.)

To load a file : 1 Push the cursor key é or ê to select the best fitting file. 2 Press ENTER to select.

A confirm Load file menu will be displayed with the newly created file and the one on which the new file is based on.

3 Press ENTER to confirm the new creation or EXIT to return to the

load file menu.

Note: When scrolling through the files, the image will be adapted according to the settings of the selected file (on line adaptation).

If the displayed image is not correct after selecting the best fitting file, go to the Edit menu, select the active file and change the File settings.

FILE SERVICE

LOAD

EDIT

RENAME

COPY

Select with or

then <ENTER>

Filename Src Resolution

<EXIT> to return.

----------------------------------------------------Video525.s01 1 675x240i Video525.c01 1 675x240i Video525.c02 1 675x240i

----------------------------------------------------Active file : Video525.c50

Select with or ,

<ENTER> to accept

<ENTER> to confirm

LOAD FILE

FILTER LIST [All]

<EXIT> to return.

CONFIRM

LOAD FILE

Create file Video525.c02 based on file

Video525.s01?

<EXIT> to return

During a load file, the actual active file is displayed next to the indication 'Active file'.

8-2

5976069 BARCOREALITY 6400 14032000

Page 30

Edit File

The Edit file menu makes it possible to change the settings of the file according to the real settings of the connected source. Consult the source specification before entering the data.

To start up the EDIT menu: 1 Push the cursor key é or ê to highlight 'Edit'. 2 Press ENTER to select.

The Edit file adaptation menu will be displayed. 3 Select the file which must be edited (mostly the active file). 4 Press ENTER.

The file name will be displayed in the upper right corner. The following items can be adjusted :

Total quantity horizontal pixels Active quantity horizontal pixels Horizontal start in pixels Horizontal period in µs (is automatically adapted during the installation of a file with LOAD) Total vertical lines (is automatically adapted during the installation of a file with LOAD) Active vertical lines Vertical start in lines Interlaced : toggle on/off (is automatically set to its correct position during the installation of a file with LOAD)

All settings can individually be changed. 1 Push the cursor key é or ê to select an item.

The color of the selected item will change and follow one of

the three methods to change the value.

a. method 1: 1 press ENTER to activate the digits 2 enter directly with the numeric keys on the RCU or local

keypad the new value or

Random Access Adjustment Mode

FILE SERVICE

LOAD

EDIT

RENAME

COPY

Select with or

then <ENTER>

Filename Src Resolution

<EXIT> to return.

----------------------------------------------------Video525.s01 1 675x240i Video525.c01 1 675x240i Video525.c02 1 675x240i

----------------------------------------------------Active file : Video525.c50

HORIZONTAL TO TA L 1344 PIXELS ACTIVE 1024 PIXELS START 296 PIXELS PERIOD 20.678 µS VERTICAL (FIELD) TO TAL 806 LINES ACTIVE 768 LINES START 36 LINES INTERLACED [OFF] READ AMDS OPTIONS

, , , <ENTER>, <EXIT>

EDIT FILE

Select with or ,

<ENTER> to accept

<EXIT> to return.

EDIT FILE xga.s30

b. method 2: 1 Press ENTER to activate the digits 2 Push the cursor key è or ç to select the changing digit. 3 Push the cursor key é or ê to scroll to desired digit. 4 When finished press ENTER to confirm.

c. method 3 1 Counting up or down by pushing the cursor key è or ç .

How to find the correct values for the displayed item?

During the installation of a file with LOAD, the horizontal period, the total number of vertical lines and the interlaced mode are automatically measured and filled in in the menu table. These values will be available when starting up the EDIT procedure of an active file.

(Caution : Do not adjust these settings on an active file, they are used to identify the input source file.)

If the value for "Horizontal Total Pixels" is wrong, sampling mistakes (small vertical bars in the projected image) will be seen in the image. Select "Total" and adjust the pixel quantity. Adjust for zero bars (hint: if the number of bars increase, adjust in the other direction).

The "Active Pixels" : determine the width of the window on the screen. This value is normally given in the source specifications. If not, adjust until full image is displayed (no missing pixels).

"Horizontal Start" : number of pixels between the beginning of the input signal and the start of the video information in the signal.

"Horizontal Period" : already filled in with the correct value when active file. (see caution above).

The "Vertical Total Lines" are already filled when an active file is selected to be edited (see caution above).

The "Active Lines" : number of horizontal lines determining the height of the projected image. This value is normally given in the specification of the source. If not, adjust until full image height is displayed (no missing lines)

Vertical start : number of lines between the start of the input signal and start of the image on the screen.

Interlaced [On] or [Off] : this selection is automatically filled when active file has to be edited. If the image is wrong due to mismeasurement,

use the ENTER key to toggle between [On] and [Off]. (for interlaced images, 1 frame contains 2 fields).

5976069 BARCOREALITY 6400 14032000

8-3

Page 31

Random Access Adjustment Mode

Read AMDS

AMDS = automatic mode detection & synchronisation During the installation of a file with LOAD, the system automatically measured the horizontal period, the total vertical lines and the interlaced mode. When selecting Read AMDS, the system remeasures the above indicated items.

Options

Source Number : The source number of a non-active source can be changed to any other source number. This makes it possible to create a file for future source numbers.

Clamp Position : Clamping determines the black level of the signal. The clamp pulse can be related to the leading or the trailing edge of the sync pulse. Use the ENTER key to toggle between [leading] and [trailing].

Clamp Delay : The time between the leading edge of the clamp pulse and the locked edge of the sync pulse. Can be any value between 0 and 255. Change the value by pushing the cursor key è or ç.

Clamp Width : The width of the clamp pulse Can be any value between 0 and 255. Change the value by pushing the cursor key è or ç.

Field Polarity : The field polarity function is used for interlaced images. Both rasters of the image could be shifted in a wrong way (double lines are visible in the image). This can be corrected by forcing the field polarity to [neg] or [pos]. Use the ENTER key to toggle between [pos] and [neg].

Field Select : Default [both] The field select is only used for interlaced images. One frame of an interlaced image contains two fields, an even and an odd field. The choice exists to project [both] fields on the screen or only the [even] or [odd] field. This can be useful for 3D projection. Use the ENTER key to toggle between [both], [even] and [odd].

Vertical Refresh [sync/async] : The way of updating the image information on the LCD panels. Not available for PAL-NTSC-SECAM sources. This option will be displayed in gray.

EDIT FILE OPTIONS

Source number 1 Clamp position [leading] Clamp delay 0 Clamp width 10 Field polarity [pos] Field select [both] Vertical refresh [sync] Vertical sync polarity [leading]

Select with or

<ENTER> to toggle

or to change value

<EXIT> to return

xample for clamp position [trailing]

leading edge

trailing edge

Sync pulse

Clamp pulse

Clamp width

Clamp delay

* For sources with a vertical frequency up to 60 Hz : the vertical

refresh rate is the same as the vertical frequency of the incoming source. This is a necessity to project moving images without 'motion artifacts'. For stationary images with a vertical frequency up to 60 Hz it is still possible to use asynchronous refresh. When loading Pal, Secam, NTSC-files the synchronous mode is default, for all other sources below 60 Hz asynchronous mode is default.

* For sources with a vertical frequency higher that 60 Hz : the

vertical refresh is different than the vertical frequency of the incoming source. Synchronous refresh cannot be used.

Vertical Sync Polarity : [leading] or [trailing] The vertical refresh can be synchronised with the leading sync edge or trailing sync edge. Default on [leading]. Toggling to [trailing] is only necessary for special applications where the trailing edge of the sync signal has to be taken as a reference. Use the ENTER key to toggle between [leading] or [trailing]

Press EXIT to leave the Edit File Option menu. A 'Confirm Edit File' menu will be displayed. Press ENTER to confirm and to save the new settings or EXIT to return without saving the new entered settings.

CONFIRM EDIT FILE

Save changes to file

xga.c30?

<ENTER> to confirm

<EXIT> to return

8-4

5976069 BARCOREALITY 6400 14032000

Page 32

Rename

To change the name of a selected file: 1 Push the cursor key é or ê to highlight 'Rename'. 2 Press ENTER.

The Rename selection menu will be displayed. 3 Push the cursor key é or ê to select a file name. 4 Press ENTER to select.

The Rename menu will be displayed with the selected file name already filled in, leave in the 'From file name :' area and in the 'To file name :' area.

The first character is highlighted. 1 Push the cursor key ç or è to select the desired character. 2 Change that character by pushing the cursor key é or ê.

Numeric characters can be entered directly with numeric

keys on the RCU. 3 Press ENTER to confirm. The renamed file is entered in the

list of files. 4 Press EXIT to return to the Rename menu selection. No

changes are made.

Random Access Adjustment Mode

FILE SERVICE

LOAD

EDIT

RENAME

COPY

DELETE

Select with or

then <ENTER>

<EXIT> to return.

RENAME FILE

Filename Src Resolution

----------------------------------------------------Video525.s01 1 675x240i Video525.c01 1 675x240i Video525.c02 1 675x240i

----------------------------------------------------Active file : Video525.c50

Select with or

<ENTER> to accept

<EXIT> to return.

RENAME FILE

Frome file name :

Video525.s01 To file name :

demo.c10

Select with or

Reprogram with or

or numeric keys

<ENTER> to confirm

<EXIT> to return

Copy

To copy a selected file into a new file : 1 Push the cursor key é or ê to highlight 'Copy'. 2 Press ENTER.

The Copy selection menu will be displayed. 3 Push the cursor key é or ê to select a file name. 4 Press ENTER to select.

The Copy menu will be displayed with the selected file name already filled in, in the 'From file name :' area and in the 'To file name :' area.

The first character is highlighted. 1 Push the cursor key ç or è to select the desired character. 2 Change that character by pushing the cursor key é or ê.

Numeric characters can be entered directly with numeric

keys on the RCU. 3 Press ENTER to confirm. The renamed file is entered in the

list of files. 4 Press EXIT to return to the Copy menu selection. No changes

are made.

Delete

To delete a selected file out of the list of files : 1 Push the cursor key é or ê to highlight 'Delete'. 2 Press ENTER.

The delete selection menu will be displayed. 3 Push the cursor key é or ê to select a file name. 4 Press ENTER to select.

If [All] is selected, your password has to be entered before

all files will be deleted.

FILE SERVICE

LOAD

EDIT

RENAME

COPY

DELETE

Select with or

then <ENTER>

<EXIT> to return.

Filename Src Resolution

----------------------------------------------------Video525.s01 1 675x240i Video525.c01 1 675x240i Video525.c02 1 675x240i

----------------------------------------------------Active file : Video525.c50

Select with or

<EXIT> to return.

COPY FILE

Select with or

<ENTER> to accept

<EXIT> to return.

Frome file name :

Select with or

Reprogram with or

<ENTER> to confirm

FILE SERVICE

LOAD

EDIT

RENAME

COPY

DELETE

OPTIONS

then <ENTER>

Filename Src Resolution

----------------------------------------------------Video525.s01 1 675x240i Video525.c01 1 675x240i Video525.c02 1 675x240i

----------------------------------------------------Active file : Video525.c50

Select with or

<ENTER> to accept

<EXIT> to return.

COPY FILE

xga_60.s03

To file name :

xga_60.c14

or numeric keys

<EXIT> to return

DELETE FILE

5976069 BARCOREALITY 6400 14032000

8-5

Page 33

Random Access Adjustment Mode

A confirmation menu "Delete file 'file name'?" is displayed. When you want to delete the file, press ENTER. If you do not want to delete the file, press EXIT. Note : the active file cannot be deleted.

File Options

1 Push the cursor key é or ê to highlight 'File Options'. 2 Press ENTER.

The option selection menu will be displayed.

File Sort

Press ENTER to toggle between [name] and [index] [name] : The files in the file list will be sorted on the file name. [index] : The files in the file list will be sorted on the file extension.

FILE SERVICE

LOAD

EDIT

RENAME

COPY

DELETE

OPTIONS

Select with or

then <ENTER>

<EXIT> to return.

CONFIRM

DELETE FILE

Delete file:

Video525.c01?

<ENTER> to confirm

<EXIT> to return

FILE OPTIONS

FILE SORT [NAME]

Select with or

then <ENTER>

<EXIT> to return.

Picture Tuning

1 Push the cursor key é or ê to highlight 'Picture Tuning'. 2 Press ENTER to select.

The Picture Tuning menu will be displayed.

The next items are available :

- CTI ON/OFF

- color temperature

- gamma

- decoding EBU/IRE

- dynamic color depth

- noise reduction

- input balance

CTI ON/OFF

CTI : Color Transient Improvement. To improve the transition from one color to another.

1 Push the cursor key é or ê to highlight 'CTI'. 2 Press ENTER to toggle between ON and OFF.

This function applies to PAL and NTSC video or S-video inputs only.

RANDOM ACCESS

ADJUSTMENT MODE

FILE SERVICE

PICTURE TUNING

AUDIO TUNNING

Select with or

then <ENTER>

<EXIT> to return.

PICTURE TUNING

CTI [ON]

COLOR TEMPERATURE

GAMMA

DECODING [EBU]

DYNAMIC COLOR DEPTH

NOISE REDUCTION

INPUT BALANCE

Select with or

then <ENTER>

<EXIT> to return.

PICTURE TUNING

CTI [ON]

COLOR TEMPERATURE

GAMMA

DECODING [EBU]

DYNAMIC COLOR DEPTH

NOISE REDUCTION

INPUT BALANCE

Select with or

then <ENTER>

<EXIT> to return.

8-6

5976069 BARCOREALITY 6400 14032000

Page 34

Color Temperature

Random Access Adjustment Mode

1 Push the cursor key é or ê to highlight 'Color Temperature'. 2 Press ENTER to select.

The color temperature selection menu will be displayed.

The next choices are possible :

- Projector white

- Broadcast 3200 K

- Film 5400 K

- Video 6500 K

- Computer 9300 K

- Custom balance.

Push the cursor key up or down to select a fixed color temperature or custom balance.

Projector white will provide maximum projector light output. The calibrated 'Broadcast', 'Film', 'Video' and 'Computer' presets will provide optimum color tracking. Custom balance allows the user to set his own preferred color temperature.

To adjust Custom Balance, handle as follow : 1 Push the cursor key é or ê to highlight 'Custom Balance'. 2 Press ENTER to select. 3 Push the cursor key é or ê to adjust red and push the cursor

key ç or è to adjust blue (range 0 to 2.5) in comparison with

the green color (value 1).

PICTURE TUNING

CTI [ON]

COLOR TEMPARATURE

GAMMA

DECODING [EBU]

DYNAMIC COLOR DEPTH

COLOR TEMPERATURE

PROJECTOR WHITE COMPUTER 9300K VIDEO 6500K FILM 54 00 K BROADCAST 3200K

CUSTOM BALANCE

Select with ,

then <ENTER>

<EXIT> to return.

GAIN RED

2.5

Gamma

With the gamma correction adjustment, it is possible to accurately set the gamma of the projector image.

To change the gamma value : 1 Push the cursor key é or ê to highlight 'Gamma'. 2 Press ENTER to select. 3 Change the gamma value by pushing the cursor key ç or è

until the desired value is reached. 4 Press EXIT to return to the Picture Tuning menu.

Decoding EBU/IRE

Only for NTSC signals. The possibility is offered to decode the NTSC video signals via the default American IRE standard or via the European EBU standard. Decoding a NTSC signal using the European EBU standard may result in a greenish tint.

1 Push the cursor key é or ê to highlight 'Decoding'. 2 Press ENTER to toggle between EBU or IRE. 3 Press EXIT to return.

PICTURE TUNING

CTI [ON]

COLOR TEMPERATURE

GAMMA

DECODING [EBU]

DYNAMIC COLOR DEPTH

NOISE REDUCTION

DYNAMIC COLOR DEPTH

GAMMA = 2.2

PICTURE TUNING

CTI [ON]

COLOR TEMPERATURE

GAMMA

DECODING [EBU]

NOISE REDUCTION

INPUT BALANCE

Select with or

then <ENTER>

<EXIT> to return.

5976069 BARCOREALITY 6400 14032000

8-7

Page 35

Random Access Adjustment Mode

Dynamic Color Depth

Increases color contrast for all video and data sources. To change the dynamic color depth value : 1 Push the cursor key é or ê to highlight 'Dynamic Color Depth'. 2 Press ENTER to select. 3 Change the value by pushing the cursor key ç or è until the

desired color contrast is reached. Adjustment range : 0 ... 8 Default : 4

4 Press EXIT to return to the Picture Tuning menu.

PICTURE TUNING

CTI [ON]

COLOR TEMPERATURE

GAMMA

DECODING [EBU]

DYNAMIC COLOR DEPTH

NOISE REDUCTION

INPUT BALANCE

Select with or

then <ENTER>

<EXIT> to return.

Noise Reduction

Reduces noise and pixel jitter in all video and data sources.

To change the noise reduction value : 1 Push the cursor key é or ê to highlight 'Noise Reduction'. 2 Press ENTER to select. 3 Change the value by pushing the cursor key ç or è until the

desired noise level is reached. Adjustment range : 0 ... 8

4 Press EXIT to return to the Picture Tuning menu.

Input Balance

Attention : Before starting the Input Balance function, generate a signal with dominant black and white areas.

The default values are normally loaded when selecting a source. If the image is not as desired, adjust for this source as follow :

Start with the Black Balance : 1 Push the cursor key é or ê to highlight 'Black Balance'. 2 Press ENTER to select. 3 Adjust the Brightness to a maximum value until there is just

no green noise visible in the black areas.

4 Adjust with the cursor key é or ê or ç or è until there is

no red or blue noise visible in the black areas.

PICTURE TUNING

CTI [ON]

STILL VIDEO [ON]

COLOR TEMPERATURE

GAMMA

DECODING [EBU]

DYNAMIC COLOR DEPTH

NOISE REDUCTION

INPUT BALANCE

Select with or

then <ENTER>

<EXIT> to return.

PICTURE TUNING

CTI [ON]

STILL VIDEO [ON]

COLOR TEMPERATURE

GAMMA

DECODING [EBU]

DYNAMIC COLOR DEPTH

NOISE REDUCTION

INPUT BALANCE

Select with or

then <ENTER>

<EXIT> to return.

DYNAMIC COLOR DEPTH

NOISE REDUCTION

INPUT BALANCE

WHITE BALANCE BLACK BALANCE

DEFAULT

Continue with the White Balance : 1 Push the cursor key é or ê to highlight 'White Balance'. 2 Press ENTER to select. 3 Adjust the Contrast to a maximum value until the white areas

are just white (without green noice) and return one step.

4 Adjust with the cursor key é or ê or ç or è until there is

no red or blue noise visible in the white areas.

8-8

Select with or

then <ENTER>

<EXIT> to return.

5976069 BARCOREALITY 6400 14032000

Page 36

Audio Tuning

1 Push the cursor key é or ê to highlight 'Audio Tuning'. 2 Press ENTER to select.

The Audio Tuning menu will be displayed.

The following items are available :

- Volume

- Balance

- Bass

- Treble

- Mute

- Fade

- Mode

- Video - Audio lock

Volume, Balance, Bass and Treble

When a sound control is selected by highlighting the item with the cursor key, a text box with a bar scale, icon and function name of the control, e.g. 'Volume' appears on the screen (only when text is ON). The length of the bar scale indicates the current memory setting for this source. For more information about the sound controls, see 'Sound controls with direct access' in the Chapter 'Controlling'.

Random Access Adjustment Mode

RANDOM ACCESS

ADJUSTMENT MODE

FILE SERVICE

PICTURE TUNING

AUDIO TUNING

GEOMETRY

AUDIO TUNING

VOLUME

BALANCE

BASS

TREBLE

MUTE [OFF]

FADE

MODE [STEREO]

VIDEO - AUDIO LOCK 123456 [A] [C] [B] [A] [B] [A]

Select with or

then <ENTER>

<EXIT> to return.

Mute

To stop the sound reproduction. 1 Push the cursor key é or ê to highlight 'Mute'. 2 Press ENTER to toggle between [on] or [off]

Fade

Determine where the sound signals will be reproduced. Adjust the fade as follow : 1 Push the cursor key é or ê to highlight 'Fade'. 2 Press ENTER to select. 3 Adjust the desired fade level.

The fade can be adjusted between -15 and 15.

Fade on -15 : no sound reproduction on the external loudspeakers, max on the internal loudspreaker with the same volume level as adjusted with the volume control.

Fade on 15 : no sound reproduction on the internal loudspeakers but max on the external loudspeakers with the same volume level as adjusted with the volume control.

AUDIO TUNING

VOLUME

BALANCE

BASS

TREBLE

MUTE [OFF]

FADE

MODE [STEREO]

VIDEO - AUDIO LOCK 1234 56 [A] [C] [B] [A] [B] [A]

Select with or

then <ENTER>

<EXIT> to return.

AUDIO TUNING

VOLUME

BALANCE

BASS

TREBLE

MUTE [OFF]

FADE

MODE [STEREO]

VIDEO - AUDIO LOCK 1234 56 [A] [C] [B] [A] [B] [A]

Select with or

then <ENTER>

<EXIT> to return.

5976069 BARCOREALITY 6400 14032000

8-9

Page 37

Random Access Adjustment Mode

Mode [stereo]/[mono]

The sound reproduction can be done in mono or stereo. To install the mode : 1 Push the cursor key é or ê to highlight 'Mode'. 2 Press ENTER to toggle between [stereo] or [mono].

Video - Audio lock

To lock an input source to an audio input, follow the next steps : 1 Push the cursor key é or ê to highlight the first input source. 2 Press ENTER to toggle the associated audio input between

[A], [B] or [C].

3 Push the cursor key ç or è to highlight another input source. 4 Press ENTER to toggle between [A], [B] or [C]. 5 Continue for the other inputs in the same way.

AUDIO TUNING

VOLUME

BALANCE

BASS

TREBLE

MUTE [OFF]

FADE

MODE [STEREO]

VIDEO - AUDIO LOCK 123456 [A] [C] [B] [A] [B] [A]

Select with or

then <ENTER>

<EXIT> to return.

VIDEO - AUDIO LOCK

1 234 56

[A] [C] [B] [A] [B] [A]

AUDIO TUNING

VOLUME

BALANCE

TREBLE

MUTE [OFF]

FADE

MODE [STEREO]

Select with or

then <ENTER>

<EXIT> to return.

FADE

150-15

Geometry

To start up the Geometry functions : 1 Push the cursor key é or ê to highlight 'Geometry'. 2 Press ENTER to select.

The geometry menu will be displayed.

The following adjustments are possible :

- horizontal and vertical image shift.

- horizontal and vertical image size

- side keystone (only necessary if the projector is mounted at a non standard projection angle).

- blanking

- aspect ratio

- options

The following ways are possible to adjust a geometry function :

- using the cursor key to adjust or

- entering the value with the digit keys. Therefore, press ENTER to select the indicated value and enter the desired value with the digit keys. Press ENTER to confirm the entered value.

RANDOM ACCESS

ADJUSTMENT MODE

FILE SERVICE

PICTURE TUNING

GEOMETRY

Select with or

then <ENTER>

<EXIT> to return.

GEOMETRY

SHIFT

SIZE

SIDE KEYSTONE

BLANKING

ASPECT RATIO [5:4]

OPTIONS

Select with or

then <ENTER>

<EXIT> to return.

8-10

5976069 BARCOREALITY 6400 14032000

Page 38

Shift

Random Access Adjustment Mode

The image can be shifted in a horizontal or vertical direction. To start up the shift action : 1 Push the cursor key é or ê to highlight 'Shift'. 2 Press ENTER to select. 3 Push the cursor key é or ê to shift the image in a vertical

direction. Push the cursor key ç or è to shift the image in a horizontal direction.

The default value for the shift is 0. Shifting in a vertical direction : when the shift value is positive, the image is shifted upwards, when the value is negative, the image is shifted downwards. Shifting in a horizontal direction : when the shift value is positive, the image is shifted to the right, when the value is negative, the image is shifted to the left.

Size

The size can be adjusted in a vertical or horizontal way. When adjusting the vertical size, The upper side of the image is fixed (table and ceiling mounted configurations) and only the lower side can be moved to its exact position.

When adjusting the horizontal size, the left side of the image is fixed and only the right side can be moved to its exact position.

To start up the size adjustment : 1 Push the cursor key é or ê to highlight 'Size'. 2 Press ENTER to select. 3 Push the cursor key é or ê to size the image in a vertical

direction. Push the cursor key ç or è to size the image in

a horizontal direction.

Fixed sides

GEOMETRY

SHIFT

SIZE

SIDE KEYSTONE

BLANKING

ASPECT RATIO [5:4]

OPTIONS

Select with or

then <ENTER>

<EXIT> to return.

GEOMETRY

SHIFT

SIZE

SIDE KEYSTONE

BLANKING

ASPECT RATIO [5:4]

OPTIONS

Select with or

then <ENTER>

<EXIT> to return.

Horizo nt al size adjustment

Side Keystone

The side keystone adjustment is used to align the image if the projector is mounted at a nonstandard projection angle.

To align the keystone : 1 Push the cursor key é or ê to highlight 'Side Keystone'. 2 Press ENTER to select. 3 Push the cursor key ç or è to adjust the keystone of the

image.

When the upper part of the image is wider than the lower part

of the image, push the cursor key ç. The number indication

below the bar scale will be negative.

When the upper part of the image is smaller than the lower

part of the image, push the cursor key è. The number

indication below the bar scale will be positive.

Vertical size adjustment

Example for table mount configuration

GEOMETRY

SHIFT

SIZE

SIDE KEYSTONE

BLANKING

ASPECT RATIO [5:4]

OPTIONS

Select with or

then <ENTER>

<EXIT> to return.

5976069 BARCOREALITY 6400 14032000

8-11

Page 39

Random Access Adjustment Mode

Blanking

Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). A '0' on the bar scale indicates no blanking.

To adjust the blanking : 1 Push the cursor key é or ê to highlight 'Blanking'. 2 Press ENTER to display the blanking menu.

The following blanking corrections are possible :

- top blanking

- bottom blanking

- left blanking

- right blanking

Top blanking

GEOMETRY

SHIFT

SIZE

SIDE KEYSTONE

BLANKING

ASPECT RATIO [5:4]

OPTIONS

Select with or

then <ENTER>

<EXIT> to return.

BLANKING

TOP

BOTTOM

LEFT

RIGHT

RESET

Select with or

then <ENTER>

<EXIT> to return.

Left blanking

Bottom blanking

Right blanking

BLANKING

TOP

BOTTOM

LEFT

RIGHT

Select with or

then <ENTER>

<EXIT> to return.

Adjustment of the blanking on the top of the image

Adjustment of the blanking on the bottom of the image

Correct by pushing the cursor key up or down

Adjustment of the blanking on the left side

8-12

Adjustment of the blanking on the right side

Correct by pushing the cursor key to the right or to the left

5976069 BARCOREALITY 6400 14032000

Page 40

Aspect Ratio [5:4]/[4:3]/[16:9]

To force the projector in a typical aspect ratio. E.g. projecting a 4:3 image in a 16:9 aspect ratio.

To install the desired aspect ratio : 1 Push the cursor key é or ê to highlight 'Aspect Ratio'. 2 Press ENTER to toggle between [5:4] or [4:3] or [16:9].

Options

To change the geometry options : 1 Push the cursor key é or ê to highlight 'Options'. 2 Press ENTER to display the Geometry options menu.

The next question will be asked by the projector : 'Use the same side keystone correction for all files ? [YES] or [NO]. [YES] : the same keystone correction will be used for all installed files. [NO] : the keystone has to be adjusted file per file.

1 Push the ENTER key to toggle between [YES] or [NO]. 2 Press EXIT to return to the Geometry menu.

Random Access Adjustment Mode

GEOMETRY

SHIFT

SIZE

SIDE KEYSTONE

BLANKING

ASPECT RATIO [5:4]

OPTIONS

Select with or

then <ENTER>

<EXIT> to return.

GEOMETRY

SHIFT

SIZE

SIDE KEYSTONE

BLANKING

ASPECT RATIO [5:4]

OPTIONS

GEOMETRY OPTIONS

Use the same side keystone correction

for all files ?

[YES]

<ENTER> to toggle

<EXIT> to return

5976069 BARCOREALITY 6400 14032000

8-13

Page 41

Installation Mode

INSTALLATION MODE

Starting up the Installation Mode

Push the cursor key é or ê to highlight 'Installation Mode' and then press ENTER.

The following item can be selected in the Installation mode :

Input slots : to set up the input priority. 800 Peripheral : to select the type of output module used in the RCVDS05 and the type of communication code, PPM or RC05. Configuration : to set up the projector position. OSD color : to change the color of the highlighted item. Internal Patterns No signal : background color when no signal is available. Quick Access keys Lens : lens adjustments

ADJUSTMENT MODE

Select a path from below :

AUTO IMAGE

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

INSTALLATION

INPUT SLOTS

NO SIGNAL

LENS

TEXT BOX POSITION

QUICK ACCESS KEYS

START UP MODE

more ...

Select with or

then <ENTER>

<EXIT> to return.

Input Slots

The input configuration of the variable inputs is shown in the input slots menu. To view or to change the input configuration : 1 Push the cursor key é or ê to highlight 'Input Slots'. 2 Press ENTER to select.

The internal system will scan the input slots and displays the

result in the Input slots menu.

The black indicated inputs are selectable and changeable.

The gray indicated inputs are fix inputs and are not change-

able. The indication in front of the digit means :

x : valid signal connected to the input.

- : no valid signal connected to the input.

The indication in the source description can be :

Source indication

Video or S-Video Video

S-Video

SWITCHING MODE : [BLANKING]

INSTALLATION

INPUT SLOTS

NO SIGNAL

LENS

TEXT BOX POSITION

QUICK ACCESS KEYS

START UP MODE

more ...

SLOT SELECTOR [Automatic] x 1. RGB-SS [CV or HS&VS]

- 2. RGB-SS [CV or HS&VS] x 3. VIDEO

- 4. S-VIDEO

- 5. DIGITAL INPUT

- 6. IEEE 1394

INSTALLATION

800 PERIPHERALS

CONFIGURATION

OSD COLOR

INTERNAL PATTERNS

more ...

Select with or

then <ENTER>

<EXIT> to return.

INPUT SLOTS

Select with or

<ENTER> to toggle

<EXIT> to return.

RGB analog RGB-CV : separate sync is composite video

signal on H/C input RGB-HS&VS : separate sync is horizontal and vertical sync RGB-CS : separate sync is composite sync RGB-SOG : sync on green

Component video Component Video

10-1

5976069 BARCOREALITY 6400 21082000

Page 42

Installation Mode

If a RCVDS (switched on) or VS05 is connected to the projector, it will be also indicated on the menu by adding +800 peripheral. If no 800 peripheral indication is made on the menu, there are still two possibilities :

- no RCVDS or VS05 connected or

- RCVDS is switched off.

When a 800 peripheral is connected to the projector, the input slots are not accessible with the cursor key to toggle their function.

No Signal

If there is no signal connect to the projector, the background color can be black or blue and the projector can shutdown after a certain time.

To change the background color handle as follow : 1 Push the cursor key é or ê to highlight 'No signal'. 2 Press ENTER to select.

The 'No Signal' menu will be displayed.

3 Push the cursor key é or ê to highlight 'Color'. 4 Press ENTER to toggle between [blue] or [black].

To change the shutdown setting, handle as follow : 1 Push the cursor key é or ê to highlight 'No signal'. 2 Press ENTER to select.

The 'No Signal' menu will be displayed.

3 Push the cursor key é or ê to highlight 'Shutdown'. 4 Press ENTER to toggle between [On] or [Off].

The shutdown time can be set between 5 min and 60 min. To set up the shutdown time, handle as follow : 1 Push the cursor key é or ê to highlight 'No signal'. 2 Press ENTER to select. 3 Push the cursor key é or ê to highlight 'Shutdown time'. 4 Push the cursor key é or ê to change the digits or

Enter the digits directly with the digits keys on the RCU.

INSTALLATION

INPUT SLOTS

NO SIGNAL

LENS

TEXT BOX POSITION

QUICK ACCESS KEYS

START UP MODE

more ...

Shutdown time : 5 min

NO SIGNAL

COLOR [Blue]

SHUTDOWN [Off]

Lens Adjustments

All lens adjustments are motorized and can be adjusted with the RCU. To adjust all lens functions such as zoom, focus and shift, handle as follow : 1 Push the cursor key é or ê to highlight 'Lens'. 2 Press ENTER to select.

The Adjustment pattern will be displayed. With the TEXT key it is possible to toggle between the internal adjustment pattern or the connected source.

The following items can be adjusted:

- Zoom/Focus

- Shift

Zoom/Focus/Shift

The Zoom/Focus function is only applied when a motorised zoom lens is mounted.

To focus or zoom the image :

1 Push the cursor key é or ê to zoom and ç or è to focus the

image.

2 When finished, press EXIT to return to the installation menu

or press ENTER to go to the shift function.

To shift the image :

1 Press ENTER to switch to the shift menu 2 Push the cursor key é or ê to shift the image up or down and

ç or è to shift the image left or right.

3 When finished, press EXIT to return to the shift menu or press

ENTER to go to the zoom/focus function.

INSTALLATION

INPUT SLOTS

NO SIGNAL

LENS

TEXT BOX POSITION

QUICK ACCESS KEYS

START UP MODE

more ...

Select with or

then <ENTER>

<EXIT> to return.

Lens Adjustment Zoom/Focus

Zoom with éorê

Focus with çorè

<ENTER> to Shift

<EXIT> to return

The lens can be shifted in a range of :

- vertical direction : - 2 mm to + 20 mm

- horizontal direction : - 5 mm to + 5 mm

5976069 BARCOREALITY 6400 21082000

Lens Adjustment Shift

Horizontal with çorè

Vertical with éorê

<ENTER> to Zoom/Focus

<EXIT> to return

10-2

Page 43

Installation Mode

Text Box Position

With the align function, the text box position can be changed from bottom right to automatic or center.

1 Push the cursor key é or ê to highlight 'Text Box Position'. 2 Press ENTER to select. The 'Text Box Position' menu will be

displayed. 3 Align will be selected. Press ENTER to toggle between

[Bottom Right], [Automatic] or [Center].

[Bottom Right] : text box will always be displayed in the bottom

rigth corner.

[Automatic] : the text box position depends on the aspect

ratio.

[Center] : the text box position will always be in the middle of

the image.

Quick Access Keys

The function keys on top of the RCU can be associated with an adjustment item in one of the adjustment menus. Each item which is not password protected or does not have a key on the RCU can associated to a function key. The menu Quick Access keys gives an overview of the actual programmed functions.

To get an overview, handle as follow : 1 Push the cursor key é or ê to highlight 'Quick Access Keys'. 2 Press ENTER to select.

The Quick Access Keys menu will be displayed. The following functions are factory preprogrammed :

F1 : dynamic color depth

F2 : noise reduction

F3 : configuration

F4 : Lens adjust zoom/focus

F5 : Lens adjust shift

How to program the quick access keys (function keys) : 1 Scroll through the menus until the desired menu is active 2 Push the desired function key for 3 seconds.

The message 'Quick access to this menu with Fx', where x is

the digit of the selected function key.

If the selected menu is not a valid menu for the quick access

keys the next message will be displayed : "Quick access to

this menu impossible".

INSTALLATION

INPUT SLOTS

NO SIGNAL

LENS

TEXT BOX POSITION

QUICK ACCESS KEYS

START UP MODE

more ...

Select with or

then <ENTER>

<EXIT> to return.

INSTALLATION

INPUT SLOTS

NO SIGNAL

LENS

TEXT BOX POSITION

QUICK ACCESS KEYS

START UP MODE

more ...

Select with or

then <ENTER>

<EXIT> to return.

F1 : DYNAMIC COLOR DEPTH F2 : NOISE REDUCTION F3 : CONFIGURATION F4 : LENS ADJUST ZOOM/FOCUS F5 : LENS ADJUST SHIFT

Note : '?' : auto image adjust

'*' : lens adjustments

TEXT BOX POSITION

ALIGN : [CENTER]

Select with or

then <ENTER>

<EXIT> to return.

QUICK ACCESS KEYS

Start Up Mode

During the start up, the projector can show first the identification screen or the projector starts with a blank screen. To change the start up mode, handle as follow : 1 Push the cursor key é or ê to highlight 'Start Up Mode'. 2 Press ENTER to select. The start up mode menu will be

displayed. 3 Select 'Identification' with the cursor keys and press ENTER

to toggle between [ON] and [OFF].

Identification [ON] : projector identification will be displayed

during start up.

Identification [OFF] : projector identification will not be dis-

played during start up.

10-3

INSTALLATION

INPUT SLOTS

NO SIGNAL

LENS

TEXT BOX POSITION

QUICK ACCESS KEYS

START UP MODE

more ...

Select with or

then <ENTER>

<EXIT> to return.

START UP MODE

IDENTIFICATION : [ON]

Select with or

then <ENTER>

<EXIT> to return.

5976069 BARCOREALITY 6400 21082000

Page 44

800 Peripheral

Output module selection.

When a RCVDS05 is connected to the projector, the type of output module of this RCVDS05 has to be defined in the 800 peripheral menu. The type of output module can be :

- standard output module or

- 5 cable output module.

To define the output module : 1 Push the cursor key é or ê to highlight '800 Peripheral'. 2 Press ENTER to select. 3 Push the cursor key é or ê to highlight 'Output module'. 4 Press ENTER to toggle between 'Standard' or '5-cable'.

Infrared Communication.

When a peripheral is connected to the 'Comm Port', the communication can be in PPM or RC5. The type of communication can be set to :

- PPM

- RC5

To define the communication : 1 Push the cursor key é or ê to highlight 'Infrared'.

2. Press ENTER to toggle between [PPM] or [RC5].

INSTALLATION

800 PERIPHERALS

CONFIGURATION

OSD COLOR

INTERNAL PATTERNS

SWITCHING MODE

more ...

Select with or

then <ENTER>

<EXIT> to return.

OUTPUT MODULE [STANDARD] INFRARED [PPM]

Installation Mode

800 PERIPHERAL

Configuration

The configuration of the projector can be set up as follow : 1 Push the cursor key é or ê to highlight 'Configuration'. 2 Press ENTER to select.

The Configuration menu will be displayed. For more information, see Projector configuration in chapter 4 : 'Installation Set Up'.

OSD color (On-Screen Display)

The highlighted items on the menus can be displayed in red, green or yellow. To change this color setting: 1 Push the cursor key é or ê to highlight 'OSD color'. 2 Press ENTER to select.

The OSD color menu will be displayed.

3 Push the cursor key é or ê to highlight a color. 4 Press ENTER to select.

INTERNAL PATTERNS

INSTALLATION

800 PERIPHERALS

CONFIGURATION

OSD COLOR

INTERNAL PATTERNS

SWITCHING MODE

more ...

Select with or

then <ENTER>

<EXIT> to return.

HIGHLIGHTED ITEM

INSTALLATION

800 PERIPHERALS

CONFIGURATION

OSD COLOR

SWITCHING MODE

more ...

Select with or

then <ENTER>

<EXIT> to return.

OSD COLOR

RED

GREEN

YELLOW

5976069 BARCOREALITY 6400 21082000

Select with or

then <ENTER>

<EXIT> to return.

10-4

Page 45

Installation Mode

Internal Patterns

IThe projector is equipped with different internal patterns which can be used for measurment purposes. To select an internal pattern, handle as follow : 1 Push the cursor key é or ê to highlight 'Internal Patterns'. 2 Press ENTER to select.

The internal pattern menu will be displayed. 3 Push the cursor key é or ê to highlight the Internal Patterns. 4 Press ENTER to display the select internal pattern.

The following patterns are available :

Outline

Hatch

Color Bars

Multiburst

Checker Board

Page Characters

Alpha-numeric characters

Character Sets

Switching Mode

When switching from one source to another, the time between the switch off of the first source and the upcoming new source can be filled up with a blank image or with a freeze of the last projected image.

To install the switching mode, follow the next procedure : 1 Push the cursor key é or ê to highlight 'Switching mode'. 2 Press ENTER to select.

The switching mode menu will be displayed. 3 Select 'Switching' and press ENTER to toggle between

[blanking] or [freeze].

[blanking] : by switching from one source to another the image will be blanked out and the installed color in the item 'No Signal' will be displayed.

INSTALLATION

800 PERIPHERALS

CONFIGURATION

OSD COLOR

INTERNAL PATTERNS

SWITCHING MODE

more ...

Select with or

then <ENTER>

<EXIT> to return.

INSTALLATION

800 PERIPHERALS

CONFIGURATION

OSD COLOR

INTERNAL PATTERNS

SWITCHING MODE

more ...

Select with or

then <ENTER>

<EXIT> to return.

INTERNAL PATTERNS

OUTLINE

HATCH COLOR BARS MULTIBURST

CHECKER BOARD

PAGE CHAR

ALPHA_NUMERIC CHAR

CHARACTER SETS

Select with or

then <ENTER>

<EXIT> to return.

SWITCHING MODE

SWITCHING : [BLANKING]

[freeze] : by switching from one source to another the last projected image will be frozen until the new source is displayed.

Select with or

then <ENTER>

<EXIT> to return.

10-5

5976069 BARCOREALITY 6400 21082000

Page 46

Service Mode

SERVICE MODE

Starting up the Service Mode

Push the cursor key é or ê to highlight 'Service' and then press ENTER.

Some items in the Service mode are password protected (when the password function is active). Enter the password to continue. All other password protected items are now available if you stay in the adjustment mode.

The service menu is built-up in two parts which are connected together with the 'more' item. If the desired item is not in the list of the displayed menu, select 'more' with the cursor key and push ENTER to display the other items in the service menu.

ADJUSTMENT MODE

Select a path from below :

AUTO IMAGE

RANDOM ACCESS

INSTALLATION

SERVICE

Select with or

then <ENTER>

<EXIT> to return.

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTIME HISTORY

PANEL ADJUSTMENTS

RESET INPUT BALANCE

SERVICE

IDENTIFICATION

LAMP DIMMING

MORE...

Select with or

then <ENTER>

<EXIT> to return.

SERVICE

BARCO LOGO

UNIFORMITY

I2C DIAGNOSIS

MORE...

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTIME HISTORY

LAMP DIMMING

MORE...

Select with or

then <ENTER>

<EXIT> to return.

SERVICE

BARCO LOGO

PANEL ADJUSTMENTS

UNIFORMITY

PRESET INPUT BALANCE

I2C DIAGNOSIS

MORE...

Select with or

then <ENTER>

<EXIT> to return.

BARCO

REALITY 6400

Proj. address : 001

Soft. version : 3.0

Config : front/

ceiling

Baudrate PC : 9600

text : ON

Serial no.: 1010200

Run time : 100 h

Select with or

then <ENTER>

<EXIT> to return.

CHANGE PROJ. ADDRESS

Projector address 001

common address (RC5) 0

Select with or

Reprogram with or

or numeric keys

<ENTER> to confirm

<EXIT> to return

LAMP RUNTIME HISTORY

Serial No Runtime

----------------------------------------------------> 0111121 600 h

0110031 990 h 0110010 1000 h 0000000 0 h 0000000 0 h 0000000 0 h

----------------------------------------------------<EXIT> to return

CHANGE PASSWORD

Enter new password

xxxx

Confirm new password

xxxx

Select with or

then <ENTER>

<EXIT> to return.

CHANGE BAUDRATE PC

230400 115200

57600 38400 19200

9600 4800 1200

Select with or

<ENTER> to accept

<EXIT> to return.

DIMMING

Select with or

then <ENTER>

<EXIT> to return.

CHANGE LANGUAGE

ENGLISH

Select with or

then <ENTER>

<EXIT> to return.

RESET LAMP RUN TIME

Enter the

serial number

of the new lamp

0000000

Select with or

Reprogram with or

or numeric keys

<ENTER> to confirm

<EXIT> to return

5976069 BARCOREALITY 6400 21082000

11-1

Page 47

Service Mode

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

LAMP DIMMING

MORE...

Select with or

then <ENTER>

<EXIT> to return.

SERVICE

BARCO LOGO

PANEL ADJUSTMENTS

UNIFORMITY

PRESET INPUT BALANCE

I2C DIAGNOSIS

MORE...

Select with or

then <ENTER>

<EXIT> to return.

PANEL ADJUSTMENT

Select the

color temperature

PROJECTOR WHITE

6500

Select with or

then <ENTER>

<EXIT> to return.

BARCO LOGO

STATUS : [ON]

BACKGROUND : [ON]

SHIFT

HOT KEY : [TEXT]

Select with or

<ENTER> to toggle/select

<EXIT> to return.

Identification

To display the Identification screen: 1 Push the cursor key é or ê to highlight 'Identification'. 2 Press ENTER to display the Identification screen.

The Identification screen gives an overview of :

- type of projector

- projector address

- software version

- installation configuration

- baud rate

- text ON

- projector serial number

- projector run time

PRESET INPUT BALANCE

WHITE BALANCE BLACK BALANCE

DEFAULT

Select with or

then press ENTER

I2C DIAGNOSIS

DECODER 12H # # # INPUT SELECT 16H # # # AUDIO 18H # # # MOTOR DRIVER 74H # # # LAMP DRIVER 78H # # # LCD DRIVER C0H # # # LCD DRIVER C4H # # # LCD DRIVER C8H # # # LCD DRIVER CCH # # #

DCA

UNIFORMITY

ADJUST

PURITY

DEFAULT

Select with or

then <ENTER>

<EXIT> to return.

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

LAMP DIMMING

MORE...

Select with or

then <ENTER>

<EXIT> to return.

- type of projector : BARCOREALITY 6400

- software version

- Proj. Address : to change the address of the projector, see Change Projector Address in this chapter.

- Installation : possible installations :

* Front/Ceiling * Front/Table * Rear/Ceiling

* Rear/Table To change the installation configuration follow the instructions in chapter Installation Set Up.

- Baud rate : transfer speed for communication with an IBM PC (or compatible) or MAC. The baud rate of the projector must be the same as the baud rate of the connected computer. When there is a difference, consult 'Change Baudrate PC' in this chapter.

- Projector Run Time : gives the total run time since the first start up. All projectors leave the factory with a run time of approximately 24 hours.

- Projector Serial number : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.

11-2 5976069 BARCOREALITY 6400 21082000

Page 48

Change Password

This item is password protected when the password strap is installed.

How to enable or disable the password function ?

The password function is enabled when the password strap on the controller module is installed. Consult an authorised Barco service technician to change the strap position.

How to change the password ?

1 Push the cursor key é or ê to highlight 'Change password'. 2 Press ENTER to display the Change Password menu.

4 '_' characters are displayed. A new pasword can be entered with the digit keys of the RCU or local keypad. Everytime a digit is entered, a 'X' appears on the screen. The confirm new pasword is still grayed out.

3 Press ENTER, the confirm new password item becomes

active. Press EXIT if no changes have to be made.

4 4 'x' characters are displayed in the confirm new password

area. Key in your password again with the digit keys of the RCU or local keypad.

5 Press ENTER.

If the confirm new password entery is the same as the entered new pasword, the pasword is changed.

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTIME HISTORY

DIMMING

MORE...

Select with or

then <ENTER>

<EXIT> to return.

CHANGE PASSWORD

Confirm new password

Service Mode

Enter new password

xxxx

Change Language

To change the language of the control software: 1 Push the cursor key é or ê to highlight 'Change Language'. 2 Press ENTER to display the Change Language menu. 3 Push the cursor key é o r ê to highlight the desired language. 4 Press ENTER to change the language.

Available languages : English

Change Projector Address

Projector Address

Every projector requires an individual address between 0 and 255. This address can be software installed.

To change that address: 1 Push the cursor key é or ê to highlight 'Change Projector

Address''.

2 Press ENTER to display the Change Projector Address

menu. The actual address will be filled in.

3 Push the cursor key é or ê to highlight 'Projector Address''.

The actual address will be filled in. The first digit is highlighted. Enter the new projector address with :

- the digit keys on the RCU or the local keypad or

- push the cursor key ç or è to select a digit and change the value by pushing the cursor key é or ê until the new value is reached. Continue with the other digits on the same way.

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

Select with or

then <ENTER>

<EXIT> to return.

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

DIMMING

MORE ...

Select with or

then <ENTER>

<EXIT> to return.

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

Projector address 001

<ENTER> to confirm

Select with or

then <ENTER>

<EXIT> to return.

English

Select with or

then <ENTER>

<EXIT> to return.

Common address 0

Select with or

Reprogram with or

or numeric keys

<EXIT> to return

5976069 BARCOREALITY 6400 21082000

11-3

Page 49

Service Mode

Common Address

Every projector listens to a common address. This common address can be set to '0' or '1'. When the RCU is programmed with that common address, every projector with that same common address will follow up the commands given by that RCU.

CHANGE PROJ. ADDRESS

Projector address 001

Common address 0

To change the common address : 1 Push the cursor key é or ê to highlight 'Common Address'. 2 Press ENTER to toggle between '0' and '1'.

Change Baudrate PC

The communication speed between projector and computer, e.g. PC or MAC, has 8 possible speeds. The baud rate speed can be software set. Handle as follow: 1 Push the cursor key é or ê to highlight 'Change Baudrate

PC''.

2 Press ENTER to display the Change Baudrate PC menu. The

actual baudrate will be highlighed. The following baud rates are available : 230400/115200/57600/38400/19200/9600/4800/1200

3 Push the cursor key é or ê to highlight the desired baudrate. 4 Press ENTER to select.

Reset Lamp Runtime

Reset lamp run time is only allowed when a new lamp is installed.

When Reset Lamp Run Time is selected in the Service Mode selection menu, the following warning will be displayed :

Risk of electrical shock. Reset lamp run time is reserved to qualified service personnel. If you are not qualified, press EXIT to cancel the reset operation.

Select with or

Reprogram with or <ENTER> to confirm

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

COMMON ADDRESS : 0

Select with or

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

LAMP DRIVE MODE

Select with or

then <ENTER>

-----------------------------------------------------

<EXIT> to return.

ELECTRICAL SHOCK

______________________________________________________________

RESET LAMP RUN TIME

service personnel

<ENTER> to accept

<EXIT> to return.

or numeric keys

<EXIT> to return

SERVICE

DIMMING

MORE...

then <ENTER>

<EXIT> to return.

WARNING

RISK OF

is reserved to

qualified

Lamp Run Time History

To get an overview of the different lamp run times: 1 Push the cursor key é or ê to highlight 'Lamp Run Time

History'.

2 Press ENTER to display the Lamp Run Time overview.

A listing with the lamp serial number and the corresponding run time will be displayed. The actual installed lamp will be marked.

3 Press EXIT to return to the service mode selection menu.

11-4 5976069 BARCOREALITY 6400 21082000

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

DIMMING

COMMON ADDRESS : 0

MORE...

Select with or

then <ENTER>

<EXIT> to return.

LAMP RUNTIME HISTORY

Serial No Runtime

----------------------------------------------------> 0111121 600 h

0110031 980 h 0110010 1000 h 0000000 0 h 0000000 0 h 0000000 0 h

----------------------------------------------------<ENTER> for detail

<EXIT> to return

Page 50

Dimming

Service Mode

The lamp can be dimmed. Therefore: 1 Push the cursor key é or ê to highlight 'Lamp Dimming'. 2 Press ENTER to select. 3 Push the cursor key ç or è to dim the lamp.

Remark : The projector starts always with full lamp power.

BARCO logo

The BARCO logo can be added to the image, in overlay or on a background, on any place on the screen. To add the BARCO logo or to change a setting in the BARCO logo menu: 1 Push the cursor key é or ê to highlight 'BARCO logo''. 2 Press ENTER to display the BARCO logo menu. The actual

settings will be displayed. Within this menu, three toggle settings and a shift control are available.

STATUS [ON/OFF]

ON : BARCO logo will be displayed on the screen. OFF : No BARCO logo displayed on the screen.

BACKGROUND [ON/OFF]

ON : BARCO logo will be displayed on a black background. OFF : BARCO logo will be displayed without any background.

SHIFT

By pushing the cursor key é, ê, ç or è, the BARCO logo can be positioned anywhere on the screen.

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

DIMMING

MORE...

Select with or

then <ENTER>

<EXIT> to return.

SERVICE

BARCO LOGO

PANEL ADJUSTMENTS

UNIFORMITY

PRESET INPUT BALANCE

I2C DIAGNOSIS

MORE...

BACKGROUND : [ON]

BARCO LOGO

STATUS : [ON]

SHIFT

HOT KEY : [TEXT]

Select with or

then <ENTER>

<EXIT> to return.

HOT KEY [TEXT/OFF]

OFF : no key on the RCU is used to display the BARCO logo. TEXT : the TEXT key on the RCU is used to display or to remove the BARCO logo with one single push on this key (only in operational mode).

Panel Adjustments

Changing these settings may seriously affect the performance of the projector.

All panel adjustments are factory adjusted. If not really necessary, do not touch any of these adjustments. They are useful when a new panel is installed.

When Panel Adjustments is selected in the Service Mode selection menu, the following warning will be displayed :

Panel Adjustments is reserved to qualified service personnel. If you are not qualified, press EXIT to cancel the panel adjustments.

SERVICE

BARCO LOGO

PANEL ADJUSTMENTS

UNIFORMITY

PRESET INPUT BALANCE

I2C DIAGNOSIS

MORE...

Select with or

then <ENTER>

<EXIT> to return.

PANEL ADJUSTMENTS

WARNING

is reserved to

qualified

service personnel

<ENTER> to accept

<EXIT> to return.

5976069 BARCOREALITY 6400 21082000

11-5

Page 51

Service Mode

Uniformity

Changing these settings may seriously affect the performance of the projector.

When Uniformity is selected in the Service Mode selection menu, the following warning will be displayed :

Uniformity is reserved to qualified service personnel. If you are not qualified, press EXIT to cancel the uniformity.

Preset Input Balance

Changing these settings may seriously affect the performance of the projector.

When Preset Input Balance is selected in the Service Mode selection menu, the following warning will be displayed :

Preset Input Balance is reserved to qualified service personnel. If you are not qualified, press EXIT to cancel the preset input balance.

SERVICE

BARCO LOGO

PANEL ADJUSTMENTS

UNIFORMITY

PRESET INPUT BALANCE

I2C DIAGNOSIS

MORE...

Select with or

then <ENTER>

<EXIT> to return.

PRESET INPUT BALANCE

service personnel

<ENTER> to accept

<EXIT> to return.

SERVICE

BARCO LOGO

PANEL ADJUSTMENTS

UNIFORMITY

PRESET INPUT BALANCE

I2C DIAGNOSIS

MORE...

Select with or

then <ENTER>

<EXIT> to return.

WARNING

is reserved to

qualified

WARNING

I2C diagnosis.

Gives an overview of the correct working of the I²C controlled IC's. Highlight I2C diagnosis by pushing the cursor key up or down and press ENTER to display the overview.

PRESET INPUT BALANCE

service personnel

<ENTER> to accept

<EXIT> to return.

SERVICE

BARCO LOGO

PANEL ADJUSTMENTS

UNIFORMITY

PRESET INPUT BALANCE

I2C DIAGNOSIS

MORE...

Select with or

DECODER 12H # # #

then <ENTER>

INPUT SELECT 16H # # #

<EXIT> to return.

AUDIO 18H # # # MOTOR DRIVER 74H # # # LAMP DRIVER 78H # # # LCD DRIVER C0H # # # LCD DRIVER C4H # # # LCD DRIVER C8H # # # LCD DRIVER CCH # # #

<EXIT> TO RETURN

is reserved to

qualified

I2C DIAGNOSIS

DCA

11-6 5976069 BARCOREALITY 6400 21082000

Page 52

Appendix A : Standard Source Set Up Files

STANDARD SOURCE SET UP FILES

NAME RESOLUTION FVERT FHOR FPIX PTOT PACT LTOT LACT

Hz kHz MHz

1600_48V 1600 X 600I 48,040 62,500 135,0002160 1600 651 600 1600_60V 1600 X 1200 60,000 75,000 162,000 2160 1600 1250 1200 1600_65V 1600 X 1200 65,000 81,250 175,500 2160 1600 1250 1200 1600_70V 1600 X 1200 70,000 87,500 189,000 2160 1600 1250 1200 8514_A 1024 X 384I 43,479 35,522 44,900 1264 1024 409 384 CGA 640 X 200 59,924 15,700 14,318 912 640 262 200 COMPUSC4 1024 X 480I 29,945 30,694 39,779 1296 1024 512 480 ED 735 X 480 59,943 31,470 28,638 910 735 525 480 EGA 640 X 350 59,702 21,851 16,257 744 640 366 350 EWS_50 1280 X 1024 50,000 52,350 87,948 1680 1280 1047 1024 EWS_60 1280 X 1024 60,000 63,900 107,352 1680 1280 1065 1024 EWS_60V 1280 X 1024 60,282 63,657 110,000 1728 1280 1056 1024 EWS_72 1280 X 1024 72,000 76,968 130,076 1690 1280 1069 1024 EWS_75 1280 X 1024 75,025 79,976 135,000 1688 1280 1066 1024 FMR 640 X 400I 42,323 36,440 28,570 784 640 431 400 FMTO_2 640 X 400 55,370 24,370 21,056 864 640 440 400 HD_1080I 1920 X 540I 30,000 33,750 74,250 2200 1920 562 540 HD720P 1280 X 720 60,000 45,000 74,250 1650 1200 750 720 HDMAC 1252 X 570I 25,020 31,250 39,125 1252 1024 625 570 INTER_GR 1184 X 886 67,170 61,796 92,941 1504 1184 920 886 MAC_2 640 X 480 66,667 35,000 30,240 864 640 525 480 MAC_3 512 X 384 60,147 24,480 15,667 640 512 407 384 MAC_4 560 X 384 60,147 24,480 17,234 704 560 407 384 MAC_5 512 X 342 60,158 22,259 15,670 704 512 370 342 MAC_6 832 X 624 74,546 49,722 57,280 1152 832 667 624 MAC_7 1024 X 768 74,907 60,150 80,000 1330 1024 803 768 MAC_LC 640 X 480 66,619 34,975 31,338 896 640 525 480 MAC_POR 640 X 870 74,996 68,846 57,280 832 640 918 870 MUSE 1172 X 518I 30,000 33,750 37,125 1172 1024 563 518 MXGA_60 1152 X 864 60,000 54,540 60,000 1456 1152 909 864 MXGA_70 1152 X 864 70,000 63,630 94,500 1480 1152 909 864 MXGA_75 1152 X 864 75,000 67,500 75,000 1600 1152 900 864 MXGA_80 1152 X 864 80,000 76,640 80,000 1440 1152 958 864 MXGA_85 1152 X 864 85,000 77,055 121,5 1576 1152 907 864 VIDEO525 1302 X 239I 29,970 15,734 32,207 1302 1024 263 239 VIDEO625 1024 X 278I 25,000 15,625 31,984 1310 1024 313 278 PAM500 640 X 400 60,000 26,400 22,810 864 640 440 400

Name : name of file, contains the settings

Resolution : image resolution, when followed by ...I means interlaced.

FVERT Hz : vertical frame frequency of the source

FHOR kHz : horizontal frequency of the source.

FPIX MHz : pixel frequency PTOT : total pixels on one horizontal line PACT : active pixels on one horizontal line LTOT : total lines in one field LACT : active lines in one field

5976069 BARCOREALITY 6400 210800

A-1

Page 53

Appendix A : Standard Source Set Up Files

NAME RESOLUTION FVERT FHOR FPIX PTOT PACT LTOT LACT

PAM800 1120 X 375I 44,936 36,443 50,000 1372 1120 406 375 PC98_1 640 X 400 56,416 24,823 21,050 848 640 440 400 PC98_2 1120 X 375I 39,994 32,835 47,840 1457 1120 411 375 PC98_3 1120 X 750 60,000 50,000 78,569 1571 1120 833 750 S1152_66 1152 X 900 66,004 61,846 94,500 1528 1152 937 900 S1152_76 1152 X 900 76,637 71,809 108,000 1504 1152 937 900 SDI_625 675 X 2781 25,000 15,625 13,500 864 720 313 278 SDI_525 675 X 2401 29,970 15,734 13,500 858 720 263 240 SG_50 1600 X 1200 50,000 62,500 130,313 2085 1600 1250 1200 SG_60_1 1280 X 1024 60,000 63.900 107,352 1680 1280 1065 1024 SG_60_2 1024 X 768 60,000 48.780 64,390 1320 1024 813 768 SG_60_3 960 X 680 60,000 43,200 54,432 1260 960 720 680 SG_60_4 1600 X 1200 60,000 75,000 156,375 2085 1600 1250 1200 SUNEWS67 1280 X 1024 67,189 71,691 117,000 1632 1280 1067 1024 SUNEWS76 1280 X 1024 76,107 81,130 135,000 1664 1280 1066 1024 SUNXGA60 1024 X 768 59,984 48,287 64,125 1328 1024 805 768 SUNXGA70 1024 X 768 70,041 56,596 74,250 1312 1024 808 768 SUNXGA77 1024 X 768 77,069 62,040 84,375 1360 1024 805 768 SUP_MAC 1024 X 768 60,000 48,780 63,999 1312 1024 813 768 SVGA_56V 800 X 600 56,250 35,156 36,000 1024 800 625 600 SVGA_60V 800 X 600 60,317 37,879 40,000 1056 800 628 600 SVGA_72V 800 X 600 72,084 48,080 50,003 1040 800 667 600 SVGA_75 800 X 600 75,000 46,875 75,000 1056 800 625 600 SVGA_85 800 X 600 85,000 53,635 56,250 1048 800 631 600 SVGA_100 800 X 600 100,000 62,800 100,000 1056 800 628 600 VGA_72V 640 X 480 72,800 37,856 31,496 832 640 520 480 VGA_GR 640 X 480 59,941 31,469 25,175 800 640 525 480 VGA_TXT 720 X 400 70,087 31,469 28,322 900 720 449 400 VGA75ISO 640 X 480 75,000 39,375 31,500 800 640 525 480 XGA_60 1024 X 768 60,000 48,360 64,996 1344 1024 806 768 XGA_70 1024 X 768 70,000 57,050 78,044 1368 1024 815 768 XGA_70V 1024 X 768 69,705 56,182 74,610 1328 1024 806 768 XGA_72 1024 X 768 71,955 58,140 80,000 1376 1024 808 768 XGA_75 1024 X 768 75,781 61,080 86,000 1408 1024 806 768 XGA75_GS 1024 X 768 74,534 59,701 79,284 1328 1024 801 768 XGA_85 1024X768 85,000 68,680 94,500 1376 1024 808 768 XGA_100 1024X768 100,000 80,800 100,000 1368 1024 808 768

Hz kHz MHz

A-2

5976069 BARCOREALITY 6400 210800

Page 54

Lenses

LENSES

Lens Cleaning Procedure

To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have developed recommendations for cleaning the lens. FIRST, we recommend you try to remove any material from the lens by blowing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.

A Toraysee

Proceed as follows :

1. Always wipe lenses with a CLEAN Toraysee

2. Always wipe lenses in a single direction. Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating.

3. Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.

4. If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.

5. Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the cloth.

6. Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.

Order number for a new Toraysee Other lenses can also be cleaned safely with this Toraysee

cloth is included with the lens kit.

cloth : R379058.

cloth.

5976069 BARCOREALITY 6400 21082000

B-1

Page 55

Lenses

QFD(1.27:1) R9840400 QFD(2.5:1) R9840290 QFD(1.4-2.1:1) R9840380 QFD(2.1-3.0:1) R9840390 QFD(3.5-4.5:1) R9840060 QFD(4.5-6.0:1) R9840100 QFD(7:1) R9840410

Lens formulas to calculate the projector distance.

QFG(1.27:1) Metric PD = 1.29 x SW - 0.0195 + 0.00276/SW

Inch PD

= 1.29 x SW - 0.77 + 42.78/SW

QFG(2.5:1) Metric PD = 1.324 x SW - 0.065 + 0.0297/SW

Inch PD

QFD(1.4-2.1:1) Metric PD

Inch PD

QFD(2.1-3.0:1) Metric PD

Inch PD

QFD(3.5-4.5:1) Metric PD

Inch PD

QFD(4.5-6.0:1) Metric PD

Inch PD

= 1.324 x SW - 0.77 + 46.03/SW

=1.44 x SW + 0.0287 - 0.022/SW

min

=2.20 x SW - 0.01 + 0.02/SW

max

=1.44 x SW + 1.3 - 34.10/SW

min

=2.20 x SW - 0.39 + 31.0/SW

max

= 2.13 x SW - 0.10 + 0.056/SW

min

= 2.90 x SW + 0.10 - 0.0745/SW

max

= 2.13 x SW - 0.39 + 86.80/SW

min

= 2.90 x SW + 0.39 - 115.47/SW

max

= 3.374 x SW - 0.115 + 0.0575/SW

min

= 4.433 x SW - 0.133 + 0.0556/SW

max

= 3.374 x SW - 4.53 + 89.12/SW

min

= 4.433 x SW - 5.24 + 86.18/SW

max

= 4.29 x SW - 0.02 + 0.0009/SW

min

= 5.86 x SW + 0.15 + 0.0121/SW

max

= 4.29 x SW - 0.79 + 1.395/SW

min

= 5.86 x SW + 5.91 + 18.755/SW

max

Lens program to calculate the projector distance is available on the BARCO webside : http://www.barco.com/projection_systems/customer_services/lens_program.asp

B-2

5976069 BARCOREALITY 6400 21082000

Page 56

Source Numbers 80 - 89 and 90 - 99

SOURCE NUMBERS 81 - 86 AND 91 - 96

Projector without any 800 peripheral connected.

The source numbers 81 - 86 and 91 - 96 do not correspond to physical inputs. An additional adjustment file can be created for these source numbers. This file can contain different settings. The relationship between sources 1 - 6 and 91 - 96 or between 1 - 6 and 81 - 86 is shown in the diagram below.

source input 1

source input 2

source input 3

source input 6

Follow the steps below to create a second or a third file for sources 1 to 6 :

source number 1 source number 81 source number 91

source number 2 source number 82 source number 92

source number 3 source number 83 source number 93

○○

source number 6 source number 86 source number 96

file A file A' file A''

file B file B' file B''

file C file C' file C''

file F file F' file F''

1. Select the source between 1 and 6.

2. Select the corresponding source number between 81 and 86 or 91 and 96 with the digit keys on the RCU.

3. Enter the adjustment mode and load a corresponding file. Edit this file if necessary.

4. Save the file and exit the adjustment mode.

Projector with a 800 peripheral connected.

Source numbers 91 - 99.

The source numbers 91 - 99 do not correspond to physical inputs. An additional adjustment file can be created for these source numbers (source numbers of the 800 peripheral). This file can contain different settings. The relationship between sources 1 - 9 of the 800 peripheral and 91 - 99 is shown in the diagram below.

source input 1

source input 2

source input 3

source input 9

source number 1 source number 91

source number 2 source number 92

source number 3 source number 93

○○

source number 9 source number 99

file A file A'

file B file B'

file C file C'

file I file I'

Follow the same procedure as for a projector without a 800 peripheral connected.

5976069 BARCOREALITY 6400 251099

C-1

Page 57

Source Numbers 80 - 89 and 90 - 99

Source numbers 81 - 86

Only valid if no input module is connected to slot 81 - 86 of a RCVDS05. The source numbers 81 - 86 correspond to the physical inputs 1 - 6 of the projector. e.g. When slot 1 of the projector has to be selected, key in source number 81. The relationship between the sources of slot 1 - 6 of the projector with 800 peripheral is shown in the table below.

source of slot 1 source number 81 source of slot 2 source number 82 source of slot 3 source number 83 source of slot 4 source number 84 source of slot 5 source number 85 source of slot 6 source number 86

C-2

5976069 BARCOREALITY 6400 251099

Barco R9001769, R9001760 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Unpacking and Dimensions

Installation Guidelines

Location and Functions of Control

Installation Set Up

Connections

Controlling

Start up of the Adjustment Mode

AUTO IMAGE ADJUSTMENT

Random Access Adjustment Mode

Installation Mode

Service Mode

STANDARD SOURCE SET UP FILES

Lenses

SOURCE NUMBERS 81 - 86 AND 91 - 96