Barco R9001390 User Manual

REALITY

9200 TCR+

R9001390

OWNER'S MANUAL

BARCO PROJECTION SYSTEMS

Date :
020798

REALITY

9200 TCR+

R9001390

OWNER'S MANUAL

Art. No. :

R5975938

Federal communication commission (FCC statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.

Instructions to the user :

if this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the
following measures :

- Re-orientation of the receiving antenna for the radio or television.

- Relocate the equipment with respect to the receiver.

- Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.
 Fasten cables connectors to the equipment by mounting screws.

Note :

The use of shielded cables is required to comply within the limits of Part15 of FCC rules and EN55022.

Due to constant research, the information in this manual is subject to change without notice.

Produced by BARCO NV, July 1998.
All rights reserved.

Trademarks are the rights of their respective owners.

BARCO n.v./Projection Systems

Noordlaan 5
B-8520 Kuurne
Belgium
Tel : [phone]
Fax : [phone]
E-mail : [e-mail]
Visite Barco at the web : http://www.barco.com

Printed in Belgium

Table of Contents

TABLE OF CONTENTS ...........................................................................................................................................................................i-1

UNPACKING AND DIMENSIONS ..........................................................................................................................................................1-1

Unpacking .....................................................................................................................................................................................1-1

Projector dimensions..................................................................................................................................................................... 1-1

Battery installation in the RCU...................................................................................................................................................... 1-2

INSTALLATION GUIDELINES ................................................................................................................................................................2-1

Environment .................................................................................................................................................................................. 2-1

What about ambient light ? ........................................................................................................................................................... 2-1

Which screen type? ......................................................................................................................................................................2-1

What image size? How big should the image be? ......................................................................................................................2-1

Where to install the projector? ...................................................................................................................................................... 2-2

How to install a projection lens? ...................................................................................................................................................2-2

LOCATION AND FUNCTIONS OF CONTROL ...................................................................................................................................... 3-1

Front panel terminology ................................................................................................................................................................3-1

Control panel terminology ............................................................................................................................................................. 3-1

INSTALLATION SET UP......................................................................................................................................................................... 4-1

CONNECTIONS ...................................................................................................................................................................................... 5-1

Power (mains) cord connection ....................................................................................................................................................5-1

Fuses............................................................................................................................................................................................. 5-1

Switching on ..................................................................................................................................................................................5-1

Switching to stand-by. ...................................................................................................................................................................5-2

Switching off ..................................................................................................................................................................................5-2

Input connections. ......................................................................................................................................................................... 5-2

Input module insertion into the projector ...................................................................................................................................... 5-2

Fixed RGB analog input (slot 1).................................................................................................................................................... 5-3

Fixed 5-input slot (slot 2)............................................................................................................................................................... 5-4

Video/S-video input module .......................................................................................................................................................... 5-5

RGB analog input module. ............................................................................................................................................................5-6

Component input module..............................................................................................................................................................5-7

RGB3S/RG3sB input module........................................................................................................................................................ 5-8

Serial Digital Input ......................................................................................................................................................................... 5-9

Connecting a computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS 232 input of the projector. ....................... 5-10

Set up of the baud rate for communication with a computer. ................................................................................................... 5-10

Connecting a RCVDS 05 to the projector...................................................................................................................................5-10

Connecting a VS05 to the projector............................................................................................................................................5-10

Connecting an IR Remote Receiver 800 to the projector. ......................................................................................................... 5-10

CONTROLLING....................................................................................................................................................................................... 6-1

How to use the RCU? ................................................................................................................................................................... 6-1

Projector address ..........................................................................................................................................................................6-1

How to display a projector address? ............................................................................................................................................ 6-2

How to program an address into the RCU? ................................................................................................................................. 6-2

Picture controls with direct access. ..............................................................................................................................................6-2

START UP OF THE ADJUSTMENT MODE...........................................................................................................................................7-1

Adjustment Mode .......................................................................................................................................................................... 7-1

RANDOM ACCESS ADJUSTMENT MODE ........................................................................................................................................... 8-1

Starting up the Random Access Adjustment Mode...................................................................................................................... 8-1

File service .................................................................................................................................................................................... 8-1

Load file .........................................................................................................................................................................................8-2

Edit file........................................................................................................................................................................................... 8-2

Rename .........................................................................................................................................................................................8-5

Copy .............................................................................................................................................................................................. 8-5

Delete ............................................................................................................................................................................................ 8-6

File Options ................................................................................................................................................................................... 8-6

Picture Tuning ............................................................................................................................................................................... 8-6

CTI ON/OFF .................................................................................................................................................................................. 8-7

Still Video.......................................................................................................................................................................................8-7

Color Temperature ........................................................................................................................................................................8-7

Gamma.......................................................................................................................................................................................... 8-8

Decoding .......................................................................................................................................................................................8-8

Dynamic Color Depth ....................................................................................................................................................................8-8

Noise Reduction............................................................................................................................................................................8-8

Edge Enhancement....................................................................................................................................................................... 8-9

Geometry....................................................................................................................................................................................... 8-9

Shift ............................................................................................................................................................................................... 8-9

Size..............................................................................................................................................................................................8-10

Side keystone.............................................................................................................................................................................. 8-10

Blanking....................................................................................................................................................................................... 8-11

5975938 BARCOREALITY 9200TCR+ 020798

i-1

Table of Contents

Options ........................................................................................................................................................................................ 8-11

INSTALLATION MODE .............................................................................................................. ............................................................. 9-1

Starting up the Installation Mode .................................................................................................................................................. 9-1

Input Slots ..................................................................................................................................................................................... 9-1

800 Peripheral ............................................................................................................................................................................... 9-2

Convergence ................................................................................................................................................................................. 9-2

Configuration ................................................................................................................................................................................. 9-5

OSD color ...................................................................................................................................................................................... 9-5

No Signal ....................................................................................................................................................................................... 9-5

Internal Patterns ............................................................................................................................................................................ 9-6

SERVICE MODE ...................................................................................................................................................................................10-1

Starting up the Service Mode................................................................................................... ................................................... 10-1

Identification ................................................................................................................................................................................ 10-2

Change Password ....................................................................................................................................................................... 10-3

How to enable or disable the password function ?..................................................................................................................... 10-3

How to change the password ? .................................................................................................................................................. 10-3

Change Language....................................................................................................................................................................... 10-4

Change Projector Address .......................................................................................................................................................... 10-4

Change Baudrate PC ..................................................................................................................................................................10-4

Reset Lamp Runtime .................................................................................................................................................................. 10-4

Lamp Run Time History .............................................................................................................................................................. 10-5

Lamp Control............................................................................................................................................................................... 10-5

BARCO logo ................................................................................................................................................................................ 10-5

Panel Adjustments ...................................................................................................................................................................... 10-6

Preset Input Balance................................................................................................................................................................... 10-6

I2C diagnosis. ................................................................................................................. ............................................................ 10-6

Appendix A : Standard Source Set Up Files .......................................................................................................................................... A-1

Appendix B : Lenses ............................................................................................................ .................................................................. B-1

Focusing the lens ......................................................................................................................................................................... B-1

Lens Cleaning Procedure........................................................................................................ ..................................................... B-1

Lenses .......................................................................................................................................................................................... B-2

Appendix C : Source numbers 80 - 89 and 90 - 99 ............................................................................................................................... C-1

i-2

5975938 BARCOREALITY 9200TCR+ 020798

Unpacking and Dimensions

1

234

5

379

Pull

To open

1

UNPACKING AND DIMENSIONS

Unpacking

To open the banding, pull on the clip as shown in the first drawing.

Take the projector out of its shipping carton and place it on a table.
For transportation, the projector is mounted on a wooden board with 3 bolts. Use a 13 mm wrench to remove these bolts.
When using the projector as a table mounted configuration, always mount the 3 supporting feet (see drawing below). These feet are mounted
on the same wooden board. Each foot contains one metal part and two plastic parts. To remove the feet, first turn out both plastic parts.
To remove the metal parts from the board, remove the retaining bolts. Save these bolts because these bolts must be used to mount the feet
to the projector. Mount first the metal parts with the removed bolts and turn in, then mount both plastic parts to finish the feet.

Warning : To prevent overheating of the projector as table mounted, always remove the wooden board and turn in the 3 supporting feet
to allow air circulation via the built-in dust filter at the bottom.

Save the original shipping carton and packing material, they will be
necessary if you ever have to ship your projector. For maximum
protection, repack your projector as it was originally packed at the
factory.

Contents of the complete unit (box) :

- 1 BARCOREALITY 9200TCR+ (weight ± 94,4 kg)

- 1 remote control unit RCU + 9V battery

- 1 power cable with outlet plug type CEE7.

- 1 owners manual

- 1 safety manual

- 3 supporting feet (built up in 3 parts)

Warning : Minimum 2 persons are required to turn
the projector upside down. Do not use the feet of
the projector as a pivoting point. These feet will be
damaged.

Projector dimensions

(units : mm)

25.4 mm = 1"

284.25

568.5

422.4

42

852.3

1125.3

561.28
294

150

135.2

630

208.6

15

70

5975938 BARCOREALITY 9200TCR+ 020798

1-1

Unpacking and Dimensions

Battery installation in the RCU.

A battery (not yet installed to save the battery life time) is delivered inside the plastic bag with the power
cord. To install the battery, remove the battery cover on the backside of the remote control by pushing
the indicated handle a little towards the bottom of the RCU. Lift up the top side of the cover at the same
time (fig. 1).

Insert the new 9 V battery (type E-block or equivalent) in the lower compartment and connect the battery
to the contact plate.
Insert the battery into the lower compartment and put the cover back.

Note : projector address has to be programmed on the RCU before using the RCU (see chapter
'Controlling').

Contact
plate

Battery

310a.DRW

Insert here the 'Insert card
RCU' which you can cut out
on the last page of this manual.

fig.2

fig.1

1-2

5975938 BARCOREALITY 9200TCR+ 020798

Installation Guidelines

2

INSTALLATION GUIDELINES

Installation Guidelines

Careful consideration of things such as image size, ambient light level,
projector placement and type of screen to use are critical to the
optimum use of the projection system.

Max. ambient temperature : 40 °C.
Min. ambient temperature : 0 °C.
The projector will not operate if ambient air temperature falls outside
this range (0°C- 40°C).

* Environment

Do not install the projection system in a site near heat sources such
as radiators or air ducts, or in a place subject to direct sunlight,
excessive dust or humidity. Be aware that room heat rises to the
ceiling; check that temperature near the installation site is not
excessive.

* What about ambient light ?

The ambient light level of any room is made up of direct or indirect
sunlight and the light fixtures in the room. The amount of ambient light
will determine how bright the image will appear. So, avoid direct light
on the screen.
Windows that face the screen should be covered by opaque drapery
while the set is being viewed. It is desirable to install the projection
system in a room whose walls and floor are of non-reflecting material.
The use of recessed ceiling lights and a method of dimming those
lights to an acceptable level is also important. Too much ambient light
will wash out of the projected image. This appears as less contrast
between the darkest and lightest parts of the image. With bigger
screens, the wash out becomes more important. As a general rule,
darken the room to the point where there is just sufficient light to read
or write comfortably. Spot lighting is desirable for illuminating small
areas so that interference with the screen is minimal.

* Which screen type?

There are two major categories of screens used for projection
equipment. Those used for front projected images and those for rear
projection applications.

Screens are rated by how much light they reflect (or transmit in the
case of rear projection systems) given a determined amount of light
projected toward them. The GAIN of a screen is the term used. Front
and rear screens are both rated in terms of gain. The gain of screens
range from a white matte screen with a gain of 1 (x1) to a brushed
aluminized screen with a gain of 10 (x10) or more. The choice
between higher and lower gain screens is largely a matter of
personal preference and another consideration called the Viewing
angle.
In considering the type of screen to choose, determine where the
viewers will be located and go for the highest gain screen possible.
A high gain screen will provide a brighter picture but reduce the
viewing angle.

For more information about screens, contact your local screen
supplier.

* What image size? How big should the image be?

The projector is designed for projecting an image size (video) from

1.00m (3.3ft) to 15.00m (49.2ft) with a aspect ratio of 4 to 3.

5975938 BARCOREALITY 9200TCR+ 020798

6FUHHQZLGWK

2-1

Installation Guidelines

* Where to install the projector?

Definitions of the Abbreviation on drawings

B = Distance between ceiling and top of the screen or
between floor and bottom of the screen.

A = Correction value, distance between bottom side of
projector (without feet) and middle of the lens. Value to be
subtracted from B to obtain the correct installation position. (A
value is a constant value for all screen widths and type of
lenses, A = 278.56 mm or 11 inch)

CD = Total distance between projector and ceiling or projector
and floor.

SW = Screen width.

SH = Screen height (image height).

PD = Projector Distance, distance between screen and
projector.

Inputs and computer video format input compatibility :

Some examples :

VIDEO and S-VIDEO
COMPONENT VIDEO
RGB ANALOG with STANDARD SYNC (SYNC ON GREEN or

SEPARATE SYNC)
RGB ANALOG with TRI-LEVEL SYNC (SYNC ON GREEN or
SEPARATE SYNC)
VGA : 640 x 480 pixels
MAC : 640 x 480 pixels
Super VGA : 800 x 600 pixels
XGA : 1024 x 768 pixels
SXGA : 1280 x 1024 pixels
Up to 1600 x 1280 pixels
Sources with pixel clock < 200 MHz

Lens type selection.

a) Determine the required screen width.

b) Determine the approximate position of the projector in the projection

room with regard to the screen and measure the

projector-screen distance (PD).

c) Use the lens formulas in appendix B to find the best corresponding

PD with regard to the measured projector-screen distance for the

required screen width.
The desired lens is determined (the order number is given in the tabel
in the same appendix B). Start the installation procedure for the
projector as described in the manual.

Ceiling

B

Screen

SH

SW

Screen

PD

Optical axis projection lens

SIDE VIEW

CEILING VIEW

SW

BACK VIEW

Ceiling

CD

A

Projector

CD = B - A

SH

SH

Screen

B

SW

Screen

SH

SIDE VIEW

Optical axis projection lens

PD

Floor

TOP VIEW

SW

BACK VIEW

CD = B - A

Projector

A

CD

Floor

* How to install a projection lens?

The projector is supplied without any lens.
The following lenses are available as an option :

QHD(1.2:1)
QHD(2.2:1)
HD(3.3:1)
QHD(4.0:1)

2-2

HD(5:1)
HD(7:1)
QHD(1.5-3:1)
WHD(3.5:1)

How to install the lens?

Remove the foam rubber in the opening of the lens holder.

- Take the new lens out of its shipping carton and remove the lens

covers.

- Turn the lens into the lens holder by turning clockwise.

- Focus the lens (see appendix B) and secure the correct position

with the fastener ring by turning this ring clockwise.

5975938 BARCOREALITY 9200TCR+ 020798

Location and Functions of Control

3

LOCATION AND FUNCTIONS OF CONTROL

Front Panel Terminology

1

2

3

RS232 IN : to allow communication with external compu­ter, e.g. IBM PC or compatible, Macintosh ...

RS232 OUT : used to connect to next projector, RS232IN
plug (communication link for PC or MAC to the next
projector).

Communication port : allows communication with the
800 peripherals.



0

RS232 OUT





This device complies with Part 15 of the FCC rules. O peration

9

is subject to following two conditions :

 $

(1) This device may not cause harm ful interference

I

RS 232 IN



 +]

COMMUNICATION PORT

(800-PERIPHERALS)

 

(2) This device must accept any interference received
including interference that may cause undesired operation

PROJECTOR MODE :
GREEN - OPERATION

RED - ST ANDBY

REMOTE



IR-ACKNOWLEDGED

IR-RECEIVED



DIAGNOSTICS

CODE



IR-RECEI VER



SDI IN SDI OUT







IR-Received : IR signals are received but not recognized

7

by the projector.

Diagnostics code : a) source number

8

b) error code : a two digit error code is displayed when

something goes wrong inside the projector.

IR receiver : receiver for control signals transmitted from

9

the RCU.

4

Remote : remote input for wired remote control.

Projector mode indication : indicates the status of the

5

projector.

Light off : power switch is not pressed.
Red light : power switch is pressed, projector in

stand by mode.

Green light : projector in operational mode.

6

IR-Acknowledged : IR signals are recognized.

Control Panel Terminology

a. Local keypad

Gaining access

10

11

Power switch : '1' = on, '0' = off

Power input : autoranging from 200 to 240 Vac.

Identification plate : name, serial number, art. number.

12

Voltage identification plate : name, art. number.

SDI IN - SDI OUT (option): Serial digital input and loop trough

13

output.
2 x BNC terminals.

The keypad is located behind a door, screened with the name
of the projector.

To open the door, push once on the indicated side of the door
and turn it to the front side of the projector.

5975938 BARCOREALITY 9200TCR+ 020798

3-1

Location and Functions of Control

b. Remote control

This remote control includes a battery powered infrared (IR) trans­mitter that allows the user to control the projector remotely.
This remote control is used for source selection, control,
adaptation and set up. It includes automatic storing of :

- picture controls (Brightness, Sharpness...)

- settings

Other functions of the remote control are :

- switching between standby and operational mode.

- switching to "pause" (blanked picture, full power for immediate
restarting)

- direct access to all connected sources.

- variable adjustment speed : when pushing continuously on the
control disc or the picture keys, the adjustment will be executed
in an accelerated fashion.









STANDBY






SHARPN



TEXT

PHASE

ENTER

TINT

COLOR

EXIT

PAUSE

BRIGHTN

&2175$67

Remote Control (RCU)





















67%<

$'-

3$86(

+(/3

?

0

9

7

8

6

5

43

21












7(;7

-

3+$6(

-

6+$531(66

-

7,17

-

&2/25

-

%5,*+71(66

-

&2175$67

(;,7

(17( 5

)5((=











+

+

+

+

+

+





Local keypad

Terminology

Back Light Key : has no function for this projector.

1

ADJ. : ADJUST key, to enter or exit the adjustment mode.

2

Address key (recessed key), to enter the address of the

3

projector (between 0 and 9). Press the sunk address key
with a pencil, followed by pressing one digit button between
0 and 9.

STBY : stand-by button, to start projector when the power

4

switch is switched on and to switch off the projector
without switching off the power switch.

PAUSE : to stop projection for a short time, press 'PAUSE'.

5

The image disappears but full power is retained for imme­diate restarting.

Help : on line help information (not yet available)

6

Digit buttons : direct input selection.

7

Picture controls : use these buttons to obtain the desired

8

picture analog level (see also 'Controlling').

PHASE : used to remove the instability of the image.

9

TEXT : when adjusting one of the image, e.g. controls during

10

a meeting, the displayed bar scale can be removed by
pressing 'TEXT' key first. To re-display the bar scale on the
screen, press 'TEXT' key again. 'TEXT' key only active in
operational mode.

3-2



FREEZ : press to freeze the projected image.

11

ENTER : to start up the adjustment mode or to confirm an

12

adjustment or selection in the adjustment mode.

EXIT : to leave the adjustment mode or to scroll upwards

13

when in the adjustment mode.

Control Disc Key (on RCU) or '+' and '-' keys (cursor

14

keys): to make menu selections when in the adjustment
mode.

The control disc can move forward, backward, to the right
or to the left.

Comparision between control disc movement and the use of
the cursor keys on the local keypad :
RCU = local keypad
control disc forward = '+' key up
control disc backward = '-' key down
control disc to the right = '+' key right
control disc to the left = '-' key left

Use the '+' and '-' keys (cursor keys) : to increase or
decrease the analog level of the image controls when they
are first selected.

RC operating indication : lights up when a button on the

15

remote control is pressed. (This is a visual indicator to check
the operation of the remote control)

5975938 BARCOREALITY 9200TCR+ 020798

32a

Installation Set Up

4

INSTALLATION SET UP

The projector can be installed to project images in four different
configurations : front/table, front/ceiling, rear/table and rear/ceiling.

5 HDU&HLOLQJ

5HDU 7DEOH

)URQW&HLOLQJ

)URQW7DEOH

To change the Configuration, enter the adjustment mode by pushing ADJUST or ENTER.
Highlight Installation by pushing the control disc forward or backward and press ENTER
to select. The installation menu will be displayed.

ENTER displays the Installation menu.
EXIT or ADJUST returns to operational mode.

Highlight Configuration by pushing the control disc forward or backward and press

ENTER to select. The configuration menu will be displayed.

ENTER displays the Configuration menu.
EXIT returns to the path selection menu.
ADJUST returns to operational mode.

The actual selected configuration will be highlighted.
Push the control disc forward or backward to select the corresponding configuration
with regard to the projector environment. Press ENTER to confirm your selection.

ENTER to confirm the selection.
EXIT returns to the installation menu.
ADJUST returns to operational mode.

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

Select with or

then <ENTER>

<EXIT> to return.

INSTALLATION

INPUT SLOTS

800 PERIPHERAL

CONVERGENCE

CONFIGURATION

OSD COLOR

INTERNAL PATTERNS

Select with or

then <ENTER>

<EXIT> to return.

CONFIGURATION

FRONT/TABLE

FRONT/CEILING

REAR/TABLE

REAR/CEILING

Select with or

then <ENTER>

<EXIT> to return.

5975938 BARCOREALITY 9200TCR+ 020798

4-1

Installation Set Up

4-2 5975938 BARCOREALITY 9200TCR+ 020798

Connections

COLOR

PHASE

SHARPN TINT BRIGHTN

STANDB Y

ENTER

TEXT

EXIT

PAUSE
















&2175$6 7

5

CONNECTIONS

AC Power (mains) cord connection

Use the supplied power cord to connect your projector to the wall
outlet. Plug the female power connector into the male connector at
the front of the projector.

The power input is auto-ranging from 200 to 240 VAC.
This projector may be connected to an IT-power system.

Fuses

Warning
For continued protection against fire hazard :

- refer replacement to qualified service personnel

- ask to replace with the same type of fuse.
Fuse type : T16 AH/250V

0

I

RS232 OUT

RGBV

RS 232 IN

H

0I

RS 232 IN

COMMUNIC ATION PORT

(800-PERIPHERALS)

This device complies with Part 15 of the FCC rules. Operation

is subject to following two conditions :
(1) This device may not cause harmful interference

(2) This device must accept any interference received

including interference that may cause undesired operation

PROJECTOR MODE :
GREEN - OP ERATION

RED - STANDBY

REMOTE

RGB

RS232 OUT

DIAGNOS TICS

IR-ACKNOWLEDGED

IR-RECEIVED

V

H / C

CO M MUNICATIO N P ORT

CODE IR-RECEIVER

9,'(269,' (2

(800-PERIPHERALS )

9,'(2,1387

RGB

On

V

H / C

98 27910

230V
10A
50/60 Hz

Switching on

Use the power switch to switch on.

When '0' is visible, the projector is switched off.

When '1' is visible, the projector is switched on.
When switching on with the power switch, the projector starts in the
stand by mode. The projector mode indication lamp is red.

To start image projection :
a. press the 'Stand by' button on the local keypad or on the remote
control. The projector mode indication lamp will be green.
b. press a digit button to select an input source. The projector mode
indication lamp will be green.

This device complies with Part 15 of the FCC rules. Operation

 9

is subject to following two conditions :

(1) This device may not cause harmful interference

$

0

I

RS232 OUT

5975938 BARCOREALITY 9200TCR+ 020798

RGBV

(2) This device must accept any interference received

+]

including interference that may cause undesired operation

RS 232 IN

COMMU N ICATION PORT

(800-PERIPHERALS)

H

PROJECTOR MODE :
GREEN - OPER A TION

REMOTE

RGB

RED - STANDBY

IR-ACKNOWLEDGED

IR-RECEIVED

H / C

DIAGNOS TICS

V

Projector mode indication

IR-RECEIVER

CODE

9,'(269,' (2

9,' (2 ,1387

Stand by button

3$86(

EXIT

(17(5

TEXT

)5((=

-

+

+(/3

3+$6(

-

+

0

SHARPNES S

-

+

8

TINT

-

+

6

COLOR

-

+

4

BRIGHTNESS

-

+

2

CONTRAST

ADJ

STBY

9

7

5

3

1

5-1

Connections

Lamp Run Time

When the total run time of the lamp is 970 hours or more, the following warning message
will be displayed for 1 minute. This warning message will be repeated every 30 minutes.
Press EXIT to remove the message before the minute is over.

When the total run time of the lamp is 1000 hours or more, the following warning message,
with the exact run time is displayed on the screen.

Lamp run time is 1000 hours. Operating the lamp longer than 1000 hours may damage
the projector. Please replace the lamp.

When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min.

The total lifetime of the lamp for a safe operation is 1000 hours max. Do not use it longer.
Always replace with a same type of lamp. Call a BARCO authorized service technician
for lamp replacement.

Warning : Using a lamp for more than 1000 hours is dangerous as the
lamp could explode.

Lamp run time
980 h

WARNING

Lamp run time is 1000 hours

Operating the lamp longer

than 1000 hours may damage

the projector.

Please replace the lamp

<ENTER> to continue

Switching to Stand-by.

When the projector is running and you want to go to stand-by, press
the stand-by key.

Input Connections.

The projector has three fixed and two modular input
facilities. The modular input slots (slot 3 and 4) can be filled
up with the following modules :

Video, S-video input order no. : R9827900
RGBS/RGsB analog input order no. : R9827910
RGB3S/RG3sB input order no. : R9827920
Component Video order no. : R9827930

The sequence of insertion has no importance. Duplicated
inputs can be used.

Note : When using a RCVDS05 or VS05, the input configu­ration of the projector must be as follows:

Slot 1 : not used
Slot 2 : RGB and Component video input
Slot 3 : Video input module
Slot 4 : not used

Switching Off

To switch off:

- First press STANDBY key and let the projector cool down until the
fans stop blowing, or at least 15 min.

- Switch off the projector with the power switch.

WARNING : When switching to standby, never restart the
projector (hot restrike) within the first 3 minutes to avoid
damage to the lamp.

This device complies with Part 15 of the FCC rules. Operation

9

is subject to following two conditions :
(1) This device may not cause harmful interference

$

I

RS 232 IN

RGB V

(2) This device must accept any interference received

+]

including interference that may cause undesired operation

PROJECTOR MODE :
GREEN - OPERATION

DIAGNOSTICS

CODE IR-RECEIVER

RED - STANDBY

COMMUNICATION PORT

IR-ACKNOWLEDGED

(800-PERIPHERA LS)

REMOTE

IR-RECEIVED

H

RGB

V

H / C

SDI IN SDI O UT

RGB

V

9,'(2,1387

H / C

On

98 27910

9,'(269,'(2

0

RS232 OUT

When using a RCVDS05, it is recommended to use a 5-cable
output module in the RCVDS. The outputs of this module has
to be connected to slot 2 of the projector.
To switch the projector in the 5-cable mode see chapter
'Installation mode'.

Input module insertion into the projector :

- Power down the projector and disconnect the power cord
from the wall outlet.

- Remove the dummy plate covering the chosen input slot
by turning out both screws.

- Slide the input module in the free slot. Insure the module
is seated correctly in the guide grooves.

- Press on both handles of the input module until the module
plug seats in the connector of the projector.

- Secure the input module by tightening both retaining
screws.

5-2

- Reconnect the power cord to the wall outlet and switch on the
projector.

The new installed module can be selected with the digit buttons on
the RCU or the local keypad.

5975938 BARCOREALITY 9200TCR+ 020798

21

2))

%

+

*

5

9

,13 ,13

,1387

$1$ /2*,17(5)$ &(0+]

RGB V

RGB

H / C

V

On

98 27910

RGB

H / C

V

H

9,' ( 2,1387

9,'(269,'(2

RS 232 IN

REMOTE

PROJECTOR MODE :

GREEN - OPERATI ON

RED - STANDBY

COMMUNICA TION PORT

(800-PERIPHERALS)

RS232 OUT

IR-ACKNOW LEDGED

IR-RECEIVED

DIAGNOSTICS

CODE

IR-RECEIVER

SDI IN SDI OUT

Fixed RGB analog input (slot 1)

Slot 1 has RGB analog input terminals (BNC) with separate Horizontal
and Vertical sync (RGBHV) or with composite sync input (RGBS).

Always use an interface when a computer and local monitor have
to be connected to the projector. BARCO makes a range of
intertfaces :

Universal analog interface.

Order number : R9826100.

RGB 120 MHz analog interface.

Order number : R9826570.

VGA interface

Order number 120V : R9828079.
Order number 230V : R9828070

MAC interface

Order number 120V : R9828059
Order number 230V : R9828050

MAGIK interface

Order number 120V : R9828129
Order number 230V : R9828120

RGB analog input : 5 x BNC

Red : 0.7 Vpp ± 3 dB
Blue : 0.7 Vpp ± 3 dB
Green : 0.7 Vpp ± 3 dB
Vert. sync : 1 Vpp to 4 Vpp ± 3 dB
Hor. sync / Composite sync :

1 Vpp to 4 Vpp ± 3 dB

Connections

All input signals are always 75 ohm terminated, even in the "not
selected" mode.

Slot 1 selection :

Key in 1 on the RCU or the local keypad.

Sync selection on the 'Input slots' menu.

The horizontal sync input can be set as separate sync, as separate
sync + video or as separate sync tri-level sync. To change this
setting, press ADJUST or ENTER key to start up the Adjustment mode.

Push the control disc up or down to select Installation and press
ENTER.

Use the control disc to select 'Input Slots' by pushing up or down and
press ENTER. The internal system will scan the inputs and displays
the result in the 'Input Slots' menu.

Push the control disc up or down to select the first slot. To change
the sync priority for Sync separate, press ENTER key to toggle
between CS or HS&VS and 3LSS or CV.

Possible indication :

RGB-SS [CS or HS&VS] = separate sync is composite

sync or horizontal and vertical sync.

RGB-SS [3LSS or CV] = separate sync is composite

tri-level sync or composite video.

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

Select with or

then <ENTER>

<EXIT> to return.

INSTALLATION

INPUT SLOTS

800 PERIPHIRAL

CONVERGENCE

CONFIGURATION

Slot Module type [Config]

1. RGB-SS [CV]

2. RGB-SOG

3. Video [Video]

4. Component Video

Select with or

<ENTER> to toggle

<EXIT> to return.

INPUT SLOTS

5975938 BARCOREALITY 9200TCR+ 020798

5-3

Connections

Fixed 5-Input Slot (slot 2)

Slot 2 has 5 BNC input terminals.
The following signals can be connected to these BNC connectors :

Connector name R G B H V

Input signal

RGBHV R G B H V

RGBS R G B S -

RGsB R Gs B - -

Composite Video - Video - - -

Super Video - Y - - C

Component Video - SS R-Y Y B-Y S -

Component Video - SOY R-Y Ys B-Y - -

Slot 2 selection :

Key in 2 on the RCU or the local keypad.

Selection of the signal format on the 'Input slot' menu.

To change the signal format, press ADJUST or ENTER key to
start up the Adjustment mode.

Push the control disc up or down to select Installation and press
ENTER.
Use the control disc to select 'Input Slots' by pushing up or down
and press ENTER. The internal system will scan the inputs and
displays the result in the 'Input Slots' menu.
Push the control disc up or down to select the second slot. To
change the input signal priority, press ENTER key to toggle.

RS232 OUT

RGB V

RS 232 IN

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

CO MMU NICA T IO N PO R T

H

INSTALLATION

SERVICE

(800-PERIPHERALS)

PROJECTOR MODE :
GREEN - OPERAT ION

RED - STANDBY

REMOTE

RGB

IR-ACKNOW LEDGED

IR-RECEIVED

V

H / C

DIAGNOSTICS

CODE

Possible indication :

RGB-SS [CS or HS&VS] = RGB analog signals, separate sync

is composite sync or horizontal and vertical sync.

RGB-SS [3LSS or CV] = RGB analog signals, separate sync

is composite tri-level sync or composite video.

RGB-SOG [SOG or 3LSOG] = RGB analog signals, sync on

green is composite sync or composite tri-level sync.

COMPONENT VIDEO - SS [SS or 3LSS] = separate sync is

composite sync or composite tri-level sync.

COMPONENT VIDEO - SOY [SOY or 3LSOY] = component

video with composite sync on Y or composite tri-level sync
on Y.

VIDEO
S-VIDEO

When using an RCVDS 05 with a 5 cable output module, connect
these 5 cables to this fixed 5-input slot (slot2) of the projector.
All sources of the RCVDS can now be accepted by the projector.

Select with or

then <ENTER>

<EXIT> to return.

INSTALLATION

INPUT SLOTS

800 PERIPHERAL

CONVERGENCE

CONFIGURATION

Select with or

then <ENTER>

Slot Module type [Config]

<EXIT> to return.

1. RGB-SS [CV]

2. RGB-SOG

3. Video [Video]

4. Component Video

Select with or

<ENTER> to toggle

<EXIT> to return.

INPUT SLOTS

5-4

5975938 BARCOREALITY 9200TCR+ 020798