Page 1
VISION
8200
R9001280
OWNER'S MANUAL
Page 2
Page 3
BARCO PROJECTION SYSTEMS
Date :
280497
VISION
8200
R9001280
OWNER'S MANUAL
Rev :
01
Art. No. :
R5975348
Page 4
Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, April 1997.
All rights reserved.
Trademarks are the rights of their respective owners.
Printed in Belgium
BARCO nv/Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Printed in Belgium
Page 5
Table of Contents
TABLE OF CONTENTS
i
TABLE OF CONTENTS ................................................................................................................................................................... i-1
SAFETY INSTRUCTIONS ............................................................................................................................................................... 1-1
REMARQUE SUR LA SÉCURITÉ ................................................................................................................................................... 1-2
UNPACKING AND DIMENSIONS ................................................................................................................................................... 2-1
Unpacking .............................................................................................................................................................................2-1
Projector dimensions .............................................................................................................................................................2-1
Battery installation in the RCU. .............................................................................................................................................. 2-2
INSTALLATION GUIDELINES ........................................................................................................................................................ 3-1
Environment .......................................................................................................................................................................... 3-1
What about ambient light ? ....................................................................................................................................................3-1
Which screen type? ...............................................................................................................................................................3-1
What image size? How big should the image be? ................................................................................................................. 3-1
Where to install the projector? ............................................................................................................................................... 3-2
How to install a projection lens? ............................................................................................................................................ 3-3
How to install the projector?................................................................................................................................................... 3-3
LOCATION AND FUCNTIONS OF CONTROL ................................................................................................................................ 4-1
Front panel terminology........................................................................................................ ................................................. 4-1
Control panel terminology ..................................................................................................................................................... 4-1
INSTALLATION SET UP .................................................................................................................................................................5-1
CONNECTIONS .............................................................................................................................................................................6-1
Power (mains) cord connection ............................................................................................................................................. 6-1
Fuses ....................................................................................................................................................................................6-1
Switching on .......................................................................................................................................................................... 6-1
Switching to stand-by. ........................................................................................................................................................... 6-2
Switching off.................................................................................................................. ........................................................ 6-2
Input connections. ................................................................................................................................................................. 6-2
Input module insertion into the projector ................................................................................................................................ 6-2
Video/S-video input module ................................................................................................................................................... 6-3
RGB analog input module...................................................................................................................................................... 6-4
Component input module....................................................................................................................................................... 6-5
RGB3S/RG3sB input module....................................................................................................... .......................................... 6-6
Connecting a computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS 232 input of the projector.......................... 6-7
Set up of the baud rate for communication with a computer. ................................................................................................. 6-7
Connecting a RCVDS 05 to the projector. .............................................................................................................................. 6-8
Connecting a VS05 to the projector .......................................................................................................................................6-8
Connecting an IR Remote Receiver 800 to the projector........................................................................................................ 6-8
CONTROLLING .............................................................................................................................................................................. 7-1
How to use the RCU? ............................................................................................................................................................7-1
Projector address ..................................................................................................................................................................7-1
How to display a projector address? ...................................................................................................................................... 7-2
How to program an address into the RCU? ............................................................................................................................ 7-2
Picture controls with direct access. ........................................................................................................................................ 7-2
How to get source information ............................................................................................................................................... 7-3
How to get a summary of your projector ................................................................................................................................ 7-4
SOURCE SET UP ........................................................................................................................................................................... 8-1
Input selection .......................................................................................................................................................................8-1
Installation of the settings for a input source ..........................................................................................................................8-1
Edit file ..................................................................................................................................................................................8-2
Rename ................................................................................................................................................................................8-4
Copy ..................................................................................................................................................................................... 8-4
Move .....................................................................................................................................................................................8-5
Delete ...................................................................................................................................................................................8-5
Options .................................................................................................................................................................................8-5
PICTURE CONTROL IN ADJUSTMENT MODE ..............................................................................................................................9-1
Signal operations................................................................................................................................................................... 9-1
Video offset ...........................................................................................................................................................................9-1
Gain ......................................................................................................................................................................................9-1
5975348 BARCOVISION 8200 210497
i-1
Page 6
Table of Contents
Gain adjustment per color ..................................................................................................................................................... 9-2
Smoothness .......................................................................................................................................................................... 9-2
Still Video.............................................................................................................................................................................. 9-2
Sync ..................................................................................................................................................................................... 9-2
Color balance ........................................................................................................................................................................ 9-2
Screen operations ................................................................................................................................................................. 9-3
Zoom/pan.............................................................................................................................................................................. 9-3
Configure .............................................................................................................................................................................. 9-7
Conversion............................................................................................................................................................................ 9-7
Geometry .............................................................................................................................................................................. 9-7
SERVICE MODE .......................................................................................................................................................................... 10-1
How to activate the password function ................................................................................................................................ 10-1
Start up the Service mode ................................................................................................................................................... 10-1
Convergence adjustment of the LCD panels........................................................................................................................ 10-2
Modify password ................................................................................................................................................................. 10-5
Lamp run time history.......................................................................................................................................................... 10-5
Reset lamp run time ............................................................................................................................................................ 10-5
Appendix A : Standard Source Set Up Files .................................................................................................................................... A-1
Appendix B : Battery replacement in the RCU .................................................................................................................................B-1
Appendix C : Lenses .......................................................................................................................................................................B-1
Focusing the lens ..................................................................................................................................................................B-1
Lens Cleaning Procedure ...................................................................................................................................................... B-1
Lenses ..................................................................................................................................................................................B-2
Appendix D : Source numbers 90 - 99............................................................................................ ................................................. C-1
i-2 5975348 BARCOVISION 8200 210497
Page 7
Safety Instructions
1
SAFETY INSTRUCTIONS
Projectors are built in accordance with the requirements of the
international safety standards IEC950, UL 1950 and CSA C22.2 No.
950, which are the safety standards of information technology equipment including electrical business equipment.
These safety standards impose important requirements on the use of
safety critical components, materials and isolation, in order to protect
the user or operator against the risk of electric shock and energy
hazard, and having access to live parts.
Safety standards also impose to the internal and external temperature
rises, radiation levels, mechanical stability and strength, enclosure
construction and protection against risk of fire.
Simulated single fault condition testing ensures the safety of the
equipment to the user even when the equipment's normal operation
fails.
Installation instructions
Before operating your projector please read this manual thoroughly,
and retain it for future reference.
Installation and preliminary adjustments should be performed by
qualified BARCO personnel or authorized BARCO service dealers.
OWNER’S RECORD
To prevent fire or electrical shock hazard, do not expose this
Warning
projector to rain or moisture
Federal communication commission (FCC statement)
This equipment has been tested and found to comply with the limits
for a class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Instructions to the user :
if this equipment does cause interference to radio or television
reception, the user may try to correct the interference by one or more
of the following measures :
- Re-orientation of the receiving antenna for the radio or television.
- Relocate the equipment with respect to the receiver.
- Plug the equipment into a different outlet so that the equipment and
receiver are on different branch circuits.
• Fasten cables connectors to the equipment by mounting screws.
The part number and serial number are located at the front of the
projector. Record these numbers in the spaces provided below. Refer
to them whenever you call upon your BARCO dealer regarding this
product.
PART NUMBER:
SER. NUMBER:
DEALER:
The lightning flash with an arrowhead within a
triangle is intended to tell the user that parts
inside this product are risk of electrical shock
to persons.
Note :
The use of shielded cables is required to comply within the limits of
Part15 of FCC rules and EN55022.
General safety instructions.
* All the safety and operating instructions should be read before using
this unit.
* The operating instructions manual should be retained for future
reference.
* All warnings on the projector and in the documentation manuals
should be adhered to.
* All instructions for operating and use of this equipment must be
followed precisely.
ON SAFETY
* This product should be operated from an AC power source. This
projector may be connected to an IT-power system.
* This product is equipped with a 3-wire grounding plug, a plug having
a third (grounding) pin. This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you are unable to insert the
plug into the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the purpose of the grounding-type
plug.
WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE
GROUNDED (EARTHED) via the supplied 3 conductor AC power
cable.
(If the supplied power cable is not the correct one, consult your
dealer.)
The exclamation point within a triangle is
intended to tell the user that important operating and/or servicing instructions are included
in the technical documentation for this equipment.
5975348 BARCOVISION 8200 210497
Mains lead (AC Power cord) with CEE 7 plug:
The colors of the mains lead are colored in
accordance with the following code:
Green-and-yellow: Earth (safety earth)
Blue: Neutral
Brown: Line
1-1
Page 8
Safety Instructions
Remarque sur la Sécurité
Les projecteurs sont fabriqués conformément aux exigences des
normes de sécurité internationales IEC950, UL 1950 et CSA C22.2
No. 950. Ces normes de sécurité sont imposées aux équipements de
la technologie informatique incluant les équipements électriques.
Ces normes de sécurité imposent des exigences importantes sur
l’emploi des composantes, des matériaux et de l’isolation dont la
sécurité est critique, afin de protéger l’utilisateur contre le risque d’une
décharge électrique et d’avoir accès aux parties sous tension.
Les normes de sécurité aussi imposent des limitations concernant la
hausse de la température interne et externe, les niveaux de radiation,
la stabilité et la force mécanique, la construction du cadre métallique
à l’intérieure et la protection contre les risques d’incendie.
Les épreuves auxquelles l’équipement a été subi assurent la sécurité
totale de l’utilisateur, même lorsque l’équipement ne fonctionne pas
normalement.
Instructions pour l’installation
Lire ce manuel complètement avant de mettre l’appareil en fonctionnement et le conserver pour consultation ultérieure.
L’installation et les réglages préliminaires devraient être faits par du
personnel qualifié BARCO ou par des agents autorisés du service
BARCO.
DONNEES POUR LE PROPRIETAIRE
Le numéro de pièce et le numéro de série sont situés à l’arrière du
projecteur. Copier ces numéros dans les espaces prévus ci-dessous.
Se référer à ces numéros chaque fois que vous consultez votre agent
BARCO concernant cet appareil.
NUMERO DE PIECE :
NUMERO DE SERIE :
AGENT :
Si vous trouvez cet autocollant sur le projecteur ou sur une partie
intérieur du projecteur, l'ouvrage ne peut être effectué que par du
personnel qualifié.
ATTENTION
RISQUE D'ELECTROCUTION NE PAS OUVRIR
ATTENTION : AFIN DE REDUIRE LE RISQUE DE CHOCS
ELECTRIQUES, NE PAS ENLEVER LE COUVERCLE (OU LE DOS)
IL N'Y A PAS DE PIECES REPARABLES PAR L'UTILISATEUR A
L'INTERIEUR
LE SERVICE NE PEUT ETRE EFFECTUE QUE PAR DU PERSONNEL
QUALIFIÉ
POUR EVITER DES RISQUES D’INCENDIE OU DE CHOCS
AVERTISSEMENT
ELECTRIQUES, NE PAS EXPOSER CE PROJECTEUR A LA
PLUIE OU A L’HUMIDITE
Fédéral communication commission (FCC statement)
Cet équipement a été testé et trouvé conforme aux limites imposées
aux appareils digitaux de classe A, selon la section 15 des règles
FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences lorsque l’utilisation doit se faire dans un
environnement commercial. Cet équipement génère, utilise et peut
émettre de l’énergie aux fréquences radio, et s’il n’est pas installé
et utilisé conformément aux instructions du manuel, il peut créer des
interférences désavantageuses dans les communications radio.
L’utilisation de cet équipement dans des zones résidentielles peut
créer des interférences. Le cas échéant, l’utilisateur devra prendre
toutes les mesures requises pour les amoindrir, à ses propres frais.
Instructions pour l’utilisateur :
Si cet équipement cause des interférences de radio ou de télévision,
l’utilisateur peut essayer de corriger les interférences en appliquant
une ou plusieurs de les mesures suivantes :
- Ré-orienter l’antenne radio ou télévision.
- Déplacer l’ équipement concernant le récepteur.
- Brancher l’ appareil sur une autre prise de telle sorte que l’appareil
et le récepteur se trouvent sur différents circuits électriques.
. Fixer les connecteurs des cables a l’équipement au moyen des vis.
Remarque :
L’utilisation de câbles blindés est exigée afin d’observer les règles
de la section 15 des règles FCC et EN55022.
Prescriptions de securite générales.
* Lire toutes les prescriptions de sécurité et de fonctionnement avant
d’utiliser cet appareil.
* Le manuel de prescriptions de securite et de fonctionnement doit
être conservé pour consultation ultérieure.
* Il faut respecter tous les avertissements mentionnés sur le projecteur
et dans les manuels.
* Suivre fidèlement toutes les prescriptions d’utilisation et de
fonctionnement de cet équipement.
SECURITE
* Cet équipement doit fonctionner sur une source à courant alternatif.
Ce projecteur peut être branché sur un système à IT courant.
* Cet appareil est équipé d’un connecteur à trois broches dont une
mise à la terre. Le connecteur n’est adapté qu’à des prises de
courant du type avec terre. Ceci est une mesure de sécurité. Si le
connecteur ne s’adapte pas dans la prise, contacter votre électricien
pour remplacer la prise non valable. Ne pas compromettre le but du
connecteur de terre.
Avertissement pour les utilisateurs : CE PROJECTEUR DOIT ÊTRE
MIS À LA TERRE avec le cordon secteur fourni.
(Si le cordon secteur n'est pas correct, consulter votre revendeur.)
Cordon d’alimentation avec connecteur
CEE7
Les couleurs des fils du cordon d’alimentation
sont codées comme suit :
Vert et jaune : terre
Bleu : neutre
L’éclair avec une tête de flèche dans un triangle
Brun : sous tension (actif)
indique à l’utilisateur que les pièces à l’intérieur de
l’appareil présentent un risque de chocs électriques.
Le point d’exclamation dans un triangle indique à
l’utilisateur que des instructions de fonctionnement et/ou de service sont comprises dans la
documentation technique de cet équipement.
1-2 5975348 BARCOVISION 8200 210497
Page 9
Safety Instructions
* Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.
* To disconnect the cord, pull it out by the plug. Never pull the cord
itself.
* If an extension cord is used with this product, make sure that the total
of the ampere ratings on the products plugged into the extension
cord does not exceed the extension cord ampere rating. Also make
sure that the total of all products plugged into the wall outlet does
not exceed 15 amperes.
* Never push objects of any kind into this product through cabinet slots
as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electrical shock.
* Never spill liquid of any kind on the product. Should any liquid or solid
object fall into the cabinet, unplug the set and have it checked by
qualified service personnel before resuming operations.
* Lightning - For added protection for this video product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent
damage to the projector due to lightning and AC power-line surges.
* To reduce the lamp heat of the projector, switch the projector first
to stand-by and let the projector lamp cool down for at least 15
minutes. Then the projector may be switched off with the power
switch.
On Installation
* Do not place this projector on an unstable cart, stand, or table. The
projector may fall, causing serious damage to it.
* Do not use this projector near water.
* Use only the power cord supplied with your projector. While
appearing to be similar, other power cords have not been safety
tested at the factory and may not be used to power the projector. For
a replacement power cord, contact your dealer.
* Slots and openings in the cabinet and the sides are provided for
ventilation; to ensure reliable operation of the projector and to
protect it from overheating, these openings must not be blocked or
covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This prod-
uct should never be placed near or over a radiator or heat register.
This projector should not be placed in a built-in installation or
enclosure unless proper ventilation is provided.
- If the product has been dropped or the cabinet has been damaged;
- If the product exhibits a distinct change in performance, indicating
a need for service.
Replacement parts - When replacement parts are required, be sure
the service technician has used original BARCO replacement parts or
authorized replacement parts which have the same characteristics as
the BARCO original part. Unauthorized substitutions may result in
degraded performance and reliability, fire, electric shock or other
hazards. Unauthorized substitutions may void warranty.
Safety check - Upon completion of any service or repairs to this
projector, ask the service technician to perform safety checks to
determine that the projector is in proper operating condition.
The projector uses a 1500 W metal halide projection lamp. Replacing
the projection lamp with any other projection lamp can cause overheating or unacceptable image quality. Use only the projection lamps
specified by BARCO, or an authorized BARCO dealer or service
center.
On Cleaning
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
To keep the cabinet looking brand-new, periodically clean it with a soft
cloth. Stubborn stains may be removed with a cloth lightly dampened
with mild detergent solution. Never use strong solvents, such as
thinner or benzine, or abrasive cleaners, since these will damage the
cabinet.
To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective coating,
therefore : avoid touching the lens. To remove dust on the lens, use
a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.
Follow the lens cleaning procedure on Appendix B in the Owners
Manual.
On Repacking
Save the original shipping carton and packing material; they will come
in handy if you ever have to ship your projector. For maximum
protection, repack your set as it was originally packed at the factory.
On illumination
In order to obtain the best quality for the projected image, it is essential
that the ambient light which is allowed to fall on the screen be kept to
an absolute minimum.
* Do not block the projector cooling fans or free air movement under
and around the projector. Loose papers or other objects may not be
nearer to the projector than 4" on any side.
On Servicing
Do not attempt to service this projector yourself, as opening or
removing covers may expose you to dangerous voltage potential and
risk of electric shock! Refer all projector service to a qualified BARCO
service center.
Call for service in the following conditions :
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the projector.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating
instructions are followed.
Adjust only those controls that are covered by the operating instructions since improper adjustment of the other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to normal operation;
5975348 BARCOVISION 8200 210497
When installing the projector and screen, care must be taken to avoid
exposure to ambient light directly on the screen. Avoid adverse
illumination on the screen from direct sunlight or fluorescent lighting
fixtures.
The use of controlled ambient lighting, such as incandescent spot
light or a dimmer, is recommended for proper room illumination.
Where possible, care should also be taken to ensure that the floors
and walls of the room in which the projector is to be installed are nonreflecting, dark surfaces. Brighter surfaces will tend to reflect and
diffuse the ambient light and hence reduce the contrast of the
projected image on the screen.
1-3
Page 10
Safety Instructions
* Ne rien laisser en appui sur le cordon d’alimentation. Ne pas placer
ce cordon là où des personnes risques de marcher dessus.
* Pour débrancher le cordon, le tirer par le connecteur, jamais par le
cordon lui-même.
* Si on utilise une rallonge, vérifier que le total des courants des
appareils raccordés à cette rallonge ne dépasse pas la capacité
nominale du câble de rallonge. Vérifier aussi que la somme des
consommations des appareils raccordés à la prise murale ne
dépasse pas 15 ampères.
* Ne jamais introduire un objet quelconque dans l’appareil à travers
les fentes du boîtier, car ils pourraient être en contact avec des
points de tension dangereux ou court-circuiter des pièces, ce qui
pourrait entraîner un risque d’incendie ou de choc électrique.
* Ne jamais répandre un liquide quelconque sur l’appareil. Si un
liquide ou un objet solide tombe dans le boîtier, débrancher l’appareil et le faire vérifier par du personnel qualifié avant de reprendre
l’utilisation.
* Foudre - Pour une protection supplémentaire de cet appareil vidéo
lors d’un orage ou s’il n’est pas employé et laissé sans surveillance
pendant de longues périodes, le débrancher de la prise murale. Ceci
évite tout endommagement au projecteur par la foudre ou par des
impulsions sur le secteur.
* Avant de débrancher le projecteur, réduire la chaleur de la lampe en
commutant le projecteur en mode d’attente et laisser refroidir la
lampe du projecteur pendant 15 minutes au moins. Puis le projecteur peut être débranché par l’interrupteur secteur.
réglage d’autres commandes peut entraîner des dégâts et souvent
nécessiter un travail important par un technicien qualifié pour
remettre l’appareil en conditions de fonctionnement normal.
- Si l’appareil est tombé ou si le boîtier est endommagé.
- Si l’appareil présente des changements nets de performance,
indiquant un besoin de réparation.
Pièces de rechange - Lorsqu’on a besoin des pièces de rechange,
veiller à ce que le technicien de service utilise des pièces d’origine
BARCO ou des pièces équivalentes autorisées qui ont les mêmes
caractéristiques que la pièce d’origine BARCO. Un remplacement par
des pièces de rechange non autorisées peut nuire à la performance
et la fiabilité, entraîner incendies, chocs électriques ou d’autres
dangers. L’utilisation de pièces de rechange non autorisées peut
annuler la garantie.
Vérification de sécurité - Lorsqu’un service ou une réparation sur
ce projecteur est terminé, demander au technicien de service de faire
les vérifications de sécurité pour s’assurer que le projecteur est en
bon état de fonctionnement.
Le projecteur emploie une lampe halogène à vapeurs métalliques de
1500 W. Remplacer la lampe par une lampe de projection quelconque
peut causer la surchauffe ou une qualité de l’image inacceptable.
N’utiliser que des lampes de projection indiquées par BARCO ou un
agent autorisé de BARCO ou un service.
Nettoyage
Débrancher l’appareil de la prise avant tout nettoyage. Ne pas utiliser
des détergents liquides ou des aérosols. Utiliser un chiffon humide
pour le nettoyage.
L’Installation
* Ne pas placer le projecteur sur un chariot, un support ou une table
instable. Le projecteur risquerait de tomber causant des dégâts
sérieux au projecteur.
* Ne pas utiliser le projecteur à proximité d’eau.
* N’utiliser que le cordon d’alimentation fourni avec votre projecteur.
Bien qu’ils se ressemblent, d’autres cordons d’alimentation n’ont
pas subi des tests de sécurité dans l’usine et pour cette raison ils ne
peuvent pas être utilisés pour actionner le projecteur. Si vous avez
besoin d’un cordon d’alimentation de remplacement, contactez
votre agent.
* Les fentes et les ouvertures pourvues dans le boîtier et au dos ou
sur le fond, sont destinées à la ventilation. Pour assurer un fonctionnement fiable du projecteur et le protéger de toute surchauffe, ses
ouvertures ne doivent être ni obstruées ni recouvertes. Les
ouvertures ne devraient jamais être obstruées en plaçant l’appareil
sur un lit, un divan, un tapis ou toute autre surface similaire.
L’appareil ne devrait jamais être placé près ou au-dessus d’un
radiateur ou autre source de chaleur. Ce projecteur ne doit pas être
installé dans une installation encastrée ou fermée, sauf si une
ventilation suffisante est assurée.
* Laisser suffisamment d’espace autour du projecteur et ne pas
obstruer la circulation de l’air. Ne pas mettre des feuilles libres ou
d’autres objets plus près de 11 cm du projecteur.
Entretien et Réparation
Ne pas essayer de réparer le projecteur vous-même, puisque ouvrir
le boîtier ou l’enlèvement des blindages peuvent vous exposer à une
puissance électrique dangereuse et au risque d’une décharge
électrique.
Contacter le service technique qualifié dans les cas suivants :
- Si le cordon secteur ou la prise de courant est endommagé ou
effiloché.
- Si on a répandu du liquide dans le projecteur.
- Si l’appareil a été exposé à la pluie ou à de l’eau.
- Si l’ appareil ne fonctionne pas normalement, bien que les instructions soient correctement suivies. Ne régler que les commandes
décrites dans les instructions de fonctionnement, car un mauvais
Pour garder au boîtier son aspect neuf, le nettoyer régulièrement avec
un chiffon doux. Des tâches tenaces peuvent être enlevées avec un
chiffon humidifié par une solution de détergent doux. Ne jamais
utiliser des solvants forts, tels que du ‘thinner’ ou du benzène, ni des
produits de nettoyage abrasifs, car ils pourraient endommager le
boîtier.
Pour garantir les meilleures performance et définition, les objectifs de
projection sont spécialement traités avec un revêtement anti-reflets.
En conséquence : éviter de toucher les objectifs. Pour enlever la
poussière de l’objectif, utiliser un chiffon sec et doux. Ne pas utiliser
de chiffon humide, de solution détergente ou de diluant. Respecter la
méthode de nettoyage des objectifs indiquée dans l’annexe B au
manuel d'utilisateur.
Ré-emballage
Conserver l’emballage et les produits d’emballage d’origine, ils seront
d’un précieux secours s’il avère utile d’expédier le projecteur. Pour
une protection maximale, ré-emballer l’appareil de la même manière
qu’à l’usine.
Eclairage
Pour garantir la meilleure qualité possible de l’image projetée, il est
essentiel que l’éclairage ambiant incident sur l’écran soit réduit au
strict minimum.
Lors de l’installation du projecteur et de l’écran, il faut veiller à éviter
toute exposition directe de l’écran à la lumière ambiante. Eviter tout
éclairage perturbateur sur l’écran par des rayons du soleil ou des
éclairages fluorescents.
L’utilisation d’un éclairage ambiant contrôlable, tel qu’un spot incandescent ou un variateur de lumière est recommandée pour obtenir un
éclairage correct de la pièce. Dans la mesure du possible veiller à ce
que les parois et le sol de la pièce dans laquelle le projecteur doit être
installé soient non-réfléchissants et de couleur foncée. Des surfaces
brillantes réfléchissent et diffusent la lumière ambiante et par conséquent réduisent le contraste de l’image sur l’écran.
1-4 5975348 BARCOVISION 8200 210497
Page 11
Unpacking and Dimensions
L
1
234
5
379
2
UNP ACKING AND DIMENSIONS
Unpacking
To open the banding, pull on the clip as shown in the first drawing.
Pull
Take the projector out of its shipping carton and place it on a table.
For transportation, the projector is mounted on a wooden board with 3 bolts. Use a 13 mm wrench to remove these bolts.
When using the projector as a table mounted configuration, always mount the 3 supporting feet (see drawing below). These feet are mounted
on the same wooden board. Each food contains one metal part and two plastic parts. To remove the feed, first turn out both plastic parts.
To remove the metal parts from the board, remove the retaining bolts. Save these bolts because these bolts must be used to mount the feet
to the projector. Mount first the metal parts with the removed bolts and turn in then both plastic parts to finish the feed.
Warning : To prevent overheating of the projector as table mounted, always remove the wooden board and turn in the 3 supporting feet to
allow air circulation via the built-in dust filter at the bottom.
Save the original shipping carton and packing material, they will
come in handy if you ever have to ship your projector. For maximum
protection, repack your projector as it was originally packed at the
factory.
Contents of the shipped box :
To open
- 1 BARCOVISION 8200
- 1 remote control unit RCU + 9V battery
- 1 power cable with outlet plug type CEE7.
- 1 owner’s manual
- 3 supporting feet (built up in 3 parts)
Projector dimensions
(units : mm)
Some examples of lenses :
Name lens Lmin Lmax
(*) mm (inch) mm (inch)
HD(1.2:1) 1072 (42.20) 1087 (42.79)
HD(2.2:1) 1043 (41.06) 1070 (42.12)
HD(3.3:1) 1017 (40.04) 1072 (42.20)
HD(4.0:1) 1022 (40.24) 1162 (45.75)
HD(5:1) 1082 (42.60) 1202 (47.32)
HD(7:1) 1252 (49.29) 1372 (54.02)
HD(1.5-3:1) 1252 (49.29) 1355 (53.35)
HD(3-5.3:1)
(*) More info about lenses, see
appendix B.
5975348 BARCOVISION 8200 210497
2-1
Page 12
Unpacking and Dimensions
Battery installation in the RCU.
A battery (not yet installed to save the battery life time) is delivered inside the plastic bag with the power
cord. To install the battery, remove the battery cover on the backside of the remote control by pushing
the indicated handle a little to the bottom of the RCU. Lift up the top side of the cover at the same time
(fig. 1).
Insert the new 9 V battery (type E-block or equivalent) in the lower compartment and connect the battery
to the contact plate.
Insert the battery into the lower compartment and put the cover back.
Note : projector address has to be programmed on the RCU before using the RCU (see chapter
'Controlling').
Contact
plate
Battery
310a.DRW
Insert here the 'Insert card
RCU' which you can cut out
on the last page of this
manual.
fig.2
fig.1
2-2 5975348 BARCOVISION 8200 210497
Page 13
Installation Guidelines
Screen width
3
INST ALLA TION GUIDELINES
Installation guidelines
Careful consideration of things as image size, ambient light level,
projector placement and type of screen to use are critical to the
optimum use of the projection system.
Max. ambient temperature : 40 °C.
Min. ambient temperature : 0°C.
The projector will not operate if the ambient air tempature falls outside
this range (0°C - 40°C).
* Environment
Do not install the projection system in a site near heat sources such
as radiators or air ducts, or in a place subject to direct sunlight,
excessive dust or humidity. Be aware that room heat rises to the
ceiling; check that temperature near the installation site is not
excessive.
* What about ambient light ?
The ambient light level of any room is made up of direct or indirect
sunlight and the light fixtures in the room. The amount of ambient light
will determine how bright the image will appear. So, avoid direct light
on the screen.
Windows that face the screen should be covered by opaque drapery
while the set is being viewed. It is desirable to install the projecting
system in a room whose walls and floor are of non-reflecting material.
The use of recessed ceiling lights and a method of dimming those
lights to an acceptable level is also important. Too much ambient
light results in a ‘wash out’ of the projected image. That appears as
less contrast between the darkest and lightest parts of the image.
With bigger screens, the ‘wash out’ becomes more important. As a
general rule, darken the room to the point where there is just sufficient
light to read or write comfortably. Spot lighting is desirable for
illuminating small areas so that interference with the screen is
minimal.
* Which screen type?
There are two major categories of screens used for projection
equipment. Those used for front projected images and those for rear
projection applications.
Screens are rated by how much light they reflect (or transmit in the
case of rear projection systems) given a determined amount of light
projected toward them. The ‘GAIN’ of a screen is the term used.
Front and rear screens are both rated in terms of gain. The gain of
screens range from a white matte screen with a gain of 1 (x1) to a
brushed aluminized screen with a gain of 10 (x10) or more. The
choice between higher and lower gain screens is largely a matter of
personal preference and another consideration called the Viewing
angle.
In considering the type of screen to choose, determine where the
viewers will be located and go for the highest gain screen possible.
A high gain screen will provide a brighter picture but reduce the
viewing angle.
For more information about screens, contact your local screen
supplier.
* What image size? How big should the image be?
The projector is designed for projecting an image size (video) from
1.00m (3.3ft) to 10.00m (39ft) with a aspect ratio of 4 to 3.
5975348 BARCOVISION 8200 210497
3-1
Page 14
Installation Guidelines
* Where to install the projector?
Definitions of the Abbreviation on drawings
B = Distance between ceiling and top of the screen or
between floor and bottom of the screen.
A = Correction value, distance between bottom side of projector (without feed) and middle of the lens. Value to be subtracted from B to obtain the correct installation position. (A
value is a constant value for all screen widths and type of
lenses, A = 195 mm.)
CD = Total distance between projector and ceiling or projector
and floor.
SW = Screen width.
SH = Screen height (image height).
PD = Projector Distance, distance between screen and pro-
jector.
Ceiling
B
OF
Screen
SH
PD
Optical axis proj ection lens
SIDE VIEW
CD
A
CD = B - OF - A
Projector
Inputs and computer video format input compatibility :
Some examples :
VIDEO and S-VIDEO
COMPONENT VIDEO
RGB ANALOG with STANDARD SYNC (SYNC ON GREEN or
SEPARATE SYNC)
RGB ANALOG with TRI-LEVEL SYNC (SYNC ON GREEN or
SEPARATE SYNC)
VGA : 640 x 480 pixels
MAC : 640 x 480 pixels
Super VGA : 800 x 600 pixels (only in a window of 756 x 556 pixels)
Lens type selection.
a) determine the required screen width.
b) determine the approximate position of the projector in the projec-
tion room with regard to the screen and measure the
projector-screen distance (PD).
c) use the lens formulas in appendix B to find the best corresponding
PD with regard to the measured projector-screen distance for the
required screen width.
The desired lens is determined (the order number is given in the tabel
in the same appendix B).
Start the installation procedure for the projector as described in
the manual.
A
CD
CD = B - OF - A
Projector
SH
Screen
OF
B
Optical axis pro jection lens
PD
Floor
SIDE VIEW
SW
Screen
BOTTOM VI EW
Ceiling
SW
BACK VIEW
* How to install a projection lens?
The projector is supplied without any lens.
OF
SH
How to install the lens?
Remove the foam rubber in the opening of the lens holder.
Screen
SW
TOP VIEW
SW
SH
OF
BACK VIEW
Floor
The following lenses are available as an option :
HD(1.2:1)
HD(2.2:1)
HD(3.3:1)
HD(4.0:1)
HD(5:1)
HD(7:1)
HD(1.5-3:1)
HD(3.0-5.3:1)
WHD(3.5:1)
- Take the new lens out of its shipping carton and remove the lens
covers.
- Turn the lens into the lens holder by turning clockwise.
- Focus the lens (see appendix B) and secure the correct position
with the fastener ring by turning this ring clockwise.
3-2 5975348 BARCOVISION 8200 210497
Page 15
Location and Functions of Control
4
LOCATION AND FUNCTIONS OF CONTROL
Front panel terminology
1
2
3
RS232 IN : to allow communication with external compu-
ter, e.g. IBM PC or compatible, Macintosh ...
RS232 OUT : used to connect to next projector, RS232IN
plug (communication link for PC or MAC to the next
projector).
Communication port : allows communication with the
800 peripherals.
10
0I
RS232 OUT
1
11
RS 232 IN
2
12 13
This device complies with Part 15 of the FCC rules. Operation
is subject to following two conditions :
(1) This device may not cause harmful interference
(2) This device must accept any interference received
including interference that may cause undesired operation
PROJECTOR MODE :
REMOTE
GREEN - OPERATION
RED - STANDBY
5
COMMUNICATI ON PORT
(800-PERIPHERALS)
3 4
IR-Received : IR signals are received but not recognized
7
by the projector.
Diagnostics code : a) source number
8
b) error code : a two digits error code is displayed when
something goes wrong inside the projector.
IR receiver : receiver for control signals transmitted from
9
the RCU.
IR-ACKNOWLEDGED
IR-RECEIVED
6
DIAGNOSTICS
CODE
7 8
IR-RECEIVER
9
4
Remote : remote input for wired remote control.
Projector mode indication : indicates the status of the
5
projector.
no lighting up : power switch is not pressed.
red lighting up : power switch is pressed, projector in
stand by mode.
green lighting up : projector in operational mode.
6
IR-Acknowledged : IR signals are recognized.
Control Panel Terminology
a. Local keypad
Gaining access
10
11
Power switch : '1' = on, '0' = off
Power input : autoranging from 100 to 240 Vac.
Identification plate : name, serial number, art. number.
12
13
Voltage identification plate
The keypad is located behind a door, screened with the name
of the projector.
To open the door, push once on the indicated side of the door
and turn it to the front side of the projector.
5975348 BARCOVISION 8200 210497
9
7
56
3
1
0
8
4
2
4-1
Page 16
Location and Functions of Control
b. Remote control
This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely.
This remote control is used for source selection, control, adaptation
and set up. It includes automatic storing of :
- picture controls (Brightness, Sharpness...)
- settings
Other functions of the remote control are :
- switching between standby and operational mode.
- switching to "pause" (blanked picture, full power for immediate
restarting)
- direct access to all connected sources.
- variable adjustment speed : when pushing continuously on the
control disk or the picture keys, the adjustment will be executed
in an accelerated fashion.
0
9
7
5
3
1
STANDBY
8
6
4
SHARPN
2
TEXT
PHASE
ENTER
TINT BRIGHTN
COLOR
EXIT
PAUSE
CONTRAST
Remote Control (RCU)
15
4
14
13
12
5
10
8
9
15
1
2
3
4
5
6
7
ADJ
STBY
PAUSE
HELP
?
0
9
7
8
6
5
43
2
1
TEXT
-
PHASE
-
SHARPNESS
-
-
COLOR
-
BRIGHTNESS
-
CONTRAST
EXIT
ENTER
FREEZ
TINT
14
13
12
11
10
+
+
+
+
+
+
9
8
Local keypad
Terminology
Back light key : when activated, all keys will be lighted up
1
and visible in the dark.
ADJ. : ADJUST key, used to display on line help while in the
2
adjustment mode.
Address key (sunk key), to enter the address of the projector
3
(between 0 and 9). Press the sunk address key with a pencil,
followed by pressing one digit button between 0 and 9.
STBY : stand by button - to start projection when the
4
without switching off the power switch.
PAUSE : to stop projection for a short time, press 'PAUSE'.
5
The image disappears but full power is retained for immediate restarting.
Help : on line help information
6
Digit buttons : direct input selection.
7
Picture controls : use these buttons to obtain the desired
8
picture analog level (see also 'Controlling').
power switch is switched on.
- to switch off the projector
7
pressing 'TEXT' key first. To re-display the bar scale on the
screen, press 'TEXT' key again. 'TEXT' key only active in
operational mode.
FREEZ : press to freeze the projected image.
11
ENTER : to start up the adjustment mode or to confirm an
12
adjustment or selection in the adjustment mode.
EXIT : to leave the adjustment mode or to scroll upwards
13
when in the adjustment mode.
Control disk (on RCU) or '+' and '-' keys (cursor keys): to
14
make menu selections when in the adjustment mode.
The control disk can move forward, backward, to the right or
to the left.
Comparision between control disk movement and the use of
the cursor keys on the local keypad :
RCU = local keypad
control disk up = '+' key up
control disk down = '-' key down
control disk to the right = '+' key right
control disk to the left = '-' key left
Use the '+' and '-' keys (cursor keys) : to increase or decrease
the analog level of the image controls when they are first
selected.
32a
PHASE : used to remove the instability of the image.
9
TEXT : when adjusting one of the image, e.g. controls during
10
a meeting, the displayed bar scale can be removed by
RC operating indication : lights up when a button on the
15
remote control is pressed. (This is a visual indicator to check
the operation of the remote control)
4-2 5975348 BARCOVISION 8200 210497
Page 17
Installation Set Up
Front/Table
Front/Ceiling
5
INSTALLATION SET UP
The projector can be installed to project images in four different
configurations : front/table, front/ceiling, rear/table and rear/ceiling.
Rear/Ceiling
Rear/Table
When switching on and the projector displays an image as illustrated below, an
adaptation of the projector configuration is required.
•
•
The projector's configuration can easily be changed with the RCU or the local keypad.
Start up the menu driven procedure by pressing ENTER to display the Main Menu.
To change the Configuration, enter the adjustment mode by pushing
5975348 BARCOVISION 8200 210497
ENTER.
•
5-1
Page 18
Installation Set Up
Push the control disk up or down to highlight Systems Settings and press ENTER.
ENTER displays the System Settings menu.
EXIT returns to operational mode.
Push the control disk up or down to highlight Installation and press ENTER.
ENTER displays the Installation menu.
EXIT returns to the Main menu.
A marker indicates the actual configuration. Push the control disk up or down to
select the corresponding configuration with regard to the projector environment.
Press
ENTER to confirm your selection. The marker jumps to the selected item
and the image changes. Press EXIT EXIT EXIT (3x EXIT) to return to operational mode.
MAIN MENU
Picture Co nt r ol
Audio Control
System Settings
File service
Servic e Mode
SYSTEM SETTINGS
Lamp Control
Installation
Input slots
•
Summary
Color
INSTALLATION
Front/Table
Front/Ceiling
Rear/Table
•
Rear/Ceiling
832b
5-2 5975348 BARCOVISION 8200 210497
Page 19
Connections
6
CONNECTIONS
Power (mains) cord connection
Use the supplied power cord to connect your projector to the wall
outlet. Plug the female power connector into the male connector at
the front of the projector.
The power input is auto-ranging from 100 to 240 VAC.
This projector may be connected to an IT-power system.
Fuses
Warning
For continued protection against fire hazard :
- refer replacement to qualified service personnel
- ask to replace with the same type of fuse.
Fuse type : T12.5 AH/250V
This device complies wi t h Part 15 of the F CC rules. Operation
100 - 230 V
is subject t o following two condit ions :
(1) This device may not cause harmful int erference
9 - 4 A
RS232 OUT
(2) This device must acc ept any interference received
including interference that may cause undesired operation
60 - 50 Hz
IR-ACKNOWLEDGED
IR-RECE IVED
DIAG NOSTI CS
CODE
IR-RECE IVER
I
COMMUNICATION PORT
RS 232 IN
(800-PERIPHE RALS)
0
I
RS232 OUT
0
Switching on
Use the power switch to switch on.
When '0' is visible, the projector is switched off.
When '1' is visible, the projector is switched on.
When switching on with the power switch, the projector starts in the
stand by mode. The projector mode indication lamp is red.
To start image projection :
a. press the 'Stand by' button on the local keypad or on the remote
control. The projector mode indication lamp will be green.
b. press a digit button to select an input source. The projector mode
indication lamp will be green.
This device complies wi t h Part 15 of the F CC rules. Operation
100 - 230 V
is subject t o following two condit ions :
(1) This device may not cause harmful int erference
9 - 4 A
0
I
RS232 OUT
(2) This device must acc ept any interference received
including interference that may cause undesired operation
60 - 50 Hz
IR-ACKNOWLEDGED
IR-RECE IVED
DIAGNO STICS
CODE
IR-RECE IVER
0
9
7
5
3
1
STANDBY
8
6
TEXT
4
SHARPN TINT BRIGHTN
2
EXIT
ENTER
PAUSE
CONTRASTCOLORPHASE
Stand by button
ADJ EXIT
PAUSE
STBY TEXT
HELP
-
PHASE
-
0
9
SHARPNESS
-
7
8
TINT
-
6
5
COLOR
-
43
BRIG HTNESS
-
2
1
CONTRAST
ENTER
FREEZ
+
+
+
+
+
+
Projector mode indication
5975348 BARCOVISION 8200 280497
6-1
Page 20
Connections
When the total run time of the lamp is 970 hours or more, the following message will be
displayed for 1 minute. This message will be repeated every 30 minutes. Press EXIT to
remove the message before the minute is over.
When the total run time of the lamp is 1000 hours or more, the following message, with the
exact run time is displayed on the screen.
Lamp run time is 1000 hours. Operating the lamp longer than 1000 hours may damage
the projector. Please replace the lamp.
When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min.
The total lifetime of the lamp for a safe operation is 1000 hours max. (normal power mode).
Do not use it longer. Replace always with a same type of lamp. Call a BARCO authorized
service technician for lamp replacement.
Warning : Using a lamp for more than 1000 hours is dangerous, the
lamp could explode.
WARNING
Lamp run time is 600 hours
Operating the lamp l onger
than 60 0 hours m a y damage
the projector.
Please replace the l amp
OK
Lamp run time
980 h
Switching to stand-by.
When the projector is running and you want to go to stand-by, press
the stand-by key.
Input connections.
The projector has modular input facilities. The input slots
can be filled up with the following modules :
Video, S-video (PAL, SECAM, NTSC) input
order no. R9827900
RGBS/RGsB analog input
order no. : R9827910
RGB3S/RG3sB input
order no. : R9827920
Component Video input
order no. : R9827930
The sequence of insertion has no importance, exept when
using a RCVDS or VS05. It is even perfectly possible to
insert several input modules of one type.
Switching off
To switch off:
- press first
stop blowing ( or at least 15 min).
- switch off the projector with the power switch.
WARNING : When switching to standby, never restart projection
(hot restrike) within the first 3 minutes to avoid damage to the
lamp.
STANDBY key and let cool down until the fans
This devi ce complies with Part 15 of the F CC rules. Operation
100 - 230 V
is subject to follow ing two condi tions :
(1) Th i s device m ay n ot cause har m f ul inter ference
9 - 4 A
0
RS232 OUT
(2) Th i s device m us t accept an y interf er ence recei v ed
I
includ i ng inter ference th at may cause u ndesired o peration
60 - 50 Hz
IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOSTICS
CODE
IR-RECEIVER
Note : When using RCVDS05 or VS05, the input
configuration of the projector must be as follows:
Slot 1 : video input module
Slot 2 : RGB analog input module
Slot 3 : Component input module
Input module insertion into the projector :
- Power down the projector and disconnect the power cord
from the wall outlet.
- Remove the dummy plate covering the chosen input slot
by turning out both screws.
- Slide the input module in the free slot. Insure the module
is seated correctly in the guide grooves.
- Press on both handles of the input module until the
module plug seats in the connector of the projector.
- Secure the input module by tightening both retaining
screws.
- Reconnect the power cord to the wall outlet and switch on
the projector.
6-2 5975348 BARCOVISION 8200 280497
The new installed module can be selected with the digit buttons on
the RCU or the local keypad.
Page 21
Connections
Video/S-video input module
To the Video input :
Composite video signals from a VCR, OFF air signal decoder, etc...
1 x BNC 1.0Vpp ± 3 dB
To the S-Video input :
Separate Y-luma/C-chroma signals for higher quality playback of
Super VHS-signals.
1 x 4 pins plug (mini DIN)
pin configuration :
1 ground luminance
2 ground chrominance
3 luminance 1.0 Vpp ± 3 dB
4 chrominance 282 mVpp ± 3 dB
Input selection :
Key in the corresponding slot number on the RCU or the local
keypad. Depending on the priority setting in the Input slots
menu, Video or S-Video will be displayed. If the wrong source
type is displayed, start up the adjustment mode by pressing
ADJUST or ENTER.
RS232 OUT
On
RS 232 IN
Luma/Chroma
S-Video input
IR-ACKNOWLEDGED
IR-RECEIVED
VIDEO/S-VIDE O INPUT
Audio input not
available
DIAGNOSTICS
CODE
IR-RECEIVER
On
Composite
Video
Video input
VCR S-VHS
Push the control disk up or down to highlight System settings and
press
ENTER to display the 'System Settings menu'.
EXIT returns to operational mode.
Use the control disk to select 'Input Slots' by pushing it up or down and
press
ENTER. The internal system will scan the inputs and displays
the result in the 'Input Slots menu'.
Push the control disk up or down to select the corresponding (video
or S-video) input slot number.
To change the priority between Video and S-Video, press
ENTER
key to toggle.
TV tuner, e.g.
TVDM 40 stereo
VCR
MAIN MENU
Pictur e Cont r ol
Audio Co nt r ol
System Settings
File service
Service Mode
Straps on module level.
SYSTEM SETTINGS
Lamp Control
Installation
Input slots
•
Summary
Color
832b
INPUT SLOTS
1. RGB-SS [CV]
2. RGB-SOG
3. Video/S-Video [Video]
4. Component video-SS
+ 800-peripheral
Audio amplifier
•
837
J12
J13
Non-Floating
Floating
Floating or non floating input
5975348 BARCOVISION 8200 280497
Floating or non-floating input.
J11
Video input :
J11 : strap "yes" : non floating strap "no" : floating
S-Video input :
J12 : strap "yes" : non floating strap "no" : floating
J13 : strap "yes" : non floating strap "no" : floating
Factory preset : strap on, input non floating.
6-3
Page 22
Connections
A
A
A
A
AAAA
AAAA
A
A
A
A
A
AA
RGB analog input module.
RGB analog input terminals with separate Horizontal and Vertical
sync inputs(RGB-HV), with Composite sync input(RGB-S) or with
Sync signals on green(RGsB).
Always use an interface when a computer and local monitor have to
be connected to the projector. Interfaces to be applied :
Universal analog interface.
Order number : R9826100.
RGB 120 MHz analog interface.
Order number : R9826570.
VGA interface
Order number 120V : R9828079.
Order number 230V : R9828070
MAC interface
Order number 120V : R9828059
Order number 230V : R9828050
MAGIK interface
Order number 120V : R9828129
Order number 230V : R9828120
RGBS/RGsB analog : 5 x BNC
Red : 0.7 Vpp ± 3 dB
Blue : 0.7 Vpp ± 3 dB
Green : 0.7 Vpp ± 3 dB
1 Vpp ± 3 dB if sync on green
Vert. sync : 1 Vpp to 4 Vpp ± 3 dB
Hor. sync / Composite sync :
1 Vpp to 4 Vpp ± 3 dB
All input signals are always 75 ohm terminated, even in the "not
selected" mode.
RGB input selection :
RS232 OU T
ANALOG INTERFACE 120 MHz
ON
OFF
DIAGNOSTICS
CODE
IR-R ECEIVED
IR-R ECEIVER
AAA
AAA
AAA
AAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
A
A
A
A
A
IR-ACKNO WL ED G E D
INPUT
B
H
R
G
V
INP
INP
H / C
On
RGB ANALOG INPUT
Vert. sync
Hor. sync or Composite
sync
Red
Green
Blue
Key in the corresponding slot number on the RCU or the local
keypad.
Straps on module level :
Floating or non-floating input.
Red : J3 : strap "yes" : non floating strap "no" : floating
Green :J4 : strap "yes" : non floating strap "no" : floating
Blue : J5 : strap "yes" : non floating strap "no" : floating
H/C : J6 : strap "yes" : non floating strap "no" : floating
V : J7 : strap "yes" : non floating strap "no" : floating
Factory preset : strap "yes", non floating input
Sync selection : strap on module level.
J8 : see drawing
Factory preset : separate sync.
Sync selection on the Input Slots menu.
The horizontal sync input can be set as separate sync input or as
separate sync + video input. To change this setting, press
ENTER
key to start up the Adjustment mode..
J3
Non-Floating
Floating
J4
J8
Separate sync
J5
Sync selection
Sync on green
J6
J7
Floating o r non floati ng inp ut
6-4 5975348 BARCOVISION 8200 280497
Page 23
Connections
On
COMPONENT VIDEO INPUT
Push the control disk key up or down to select
press
ENTER.
System Settings
and
Use the control disk to select Input Slots by pushing up or down and
press
ENTER. The internal system will scan the inputs and displays
the result in the Input Slots menu.
Push the control disk up or down to select the corresponding RGB
input slot. To change the sync priority for Sync separate, press
ENTER key to toggle between CV and CS or HS&VS.
Possible indication :
RGB-SS [CV] = separate sync is composite video signal
on H/C input.
RGB-SS [CS or HS&VS] = separate sync is composite
sync or horizontal and vertical sync.
RGB-SOG = sync on green.
Component input module.
Connect your component signals (Y-luma, R-Y and B-Y), e.g. a
professional VCR to the Component input module.
Component video : 4 x BNC
R-Y : 0.7 Vpp ± 3 dB
B-Y : 0.7 Vpp ± 3 dB
Y : 0.7 Vpp ± 3 dB
1 Vpp ± 3 dB if Tri-level sync on green
Composite sync : 1 Vpp to 4 Vpp ± 3 dB
All input signals are always 75 ohm terminated, even if the module is
"not selected".
MAIN MENU
Pictur e Cont r ol
Audio Co nt r ol
System Settings
File service
Service Mode
Red - luma
SYSTEM SETTINGS
Lamp Control
Installation
Input slots
•
Summary
Color
832b
INPUT SLOTS
1. RGB-SS [CV]
2. RGB-SOG
3. Video/S-Video [Video]
4. Component video-SS
+ 800-peripheral
Luma
Blue - luma
•
837
Sync
RS232 OUT
RS 232 IN
Component input selection :
Key in the corresponding slot number on the RCU or the local keypad.
Indication on the input slot menu :
Component Video-SS = Component video with separate sync
Component Video-SOY = Component video with sync on Y
Component Video-3LSS = Component video with 3 level separate sync
Component Video-3LSOY = Component video with 3 level sync on Y
REMOTE
GREEN - OPERATION
IR-ACKNOWL EDGED
IR-REC EIVED
DIAGNOSTICS
CODE
IR-REC EIVER
Professional VCR
5975348 BARCOVISION 8200 280497
6-5
Page 24
Connections
Straps on module level :
Floating or non-floating input.
R-Y : J3 : strap "yes" : non floating strap "no" : floating
Y : J4 : strap "yes" : non floating strap "no" : floating
B-Y : J5 : strap "yes" : non floating strap "no" : floating
S : J6 : strap "yes" : non floating strap "no" : floating
Factory preset : strap "yes", non floating input
Sync selection.
J8 :
strap "no" : separate sync
strap "yes" : sync on Y.
J9 :
strap "yes" : Tri-level sync
strap "no" : normal sync.
Factory preset :
separate sync and
normal sync.
J8
Non-Floating
Floating
J9
J8
Separate sync
Floating or non floating input
J6
Sync selection
J5
Sync on Y
J4
J3
RGB3S/RG3sB input module.
Connect your RGB signals with Tri-level sync, e.g. a professional
VCR to the RGB 3 level sync input module.
RGB3S/RG3sB analog : 5 x BNC
Red : 0.7 Vpp ± 3 dB
Blue : 0.7 Vpp ± 3 dB
Green : 0.7 Vpp ± 3 dB
1 Vpp ± 3 dB if Tri-level sync on green
Vert. Tri-level sync : 1 Vpp to 4 Vpp ± 3 dB
Hor. Tri-level sync / Composite Tri-level sync:
1 Vpp to 4 Vpp ± 3 dB
All input signals are always 75 ohm terminated, even in the "not
selected" mode.
Input selection :
Key in the corresponding slot number on the RCU or the local
keypad.
Indication on the input slot menu :
RGB3L-SS = RGB with separate Tri level sync.
RGB3L-SOG = RGB with Tri level sync on green.
RS232 OUT
RS 232 IN
On
R
J9
Red
Normal Sync
G
Green
IR-ACKNOWLEDGED
Tri-level Sync
B
RGB 3-LEVEL SYNC INPUT
Blue
DIAGNO ST ICS
CODE
IR-RECEI VER
IR-RECEI VED
H / C
V
Hor. or composite
3 level sync
98 27920
Vert. 3 level
sync
HDTV VCR
6-6 5975348 BARCOVISION 8200 280497
Page 25
Connections
RS232
connection
RS232 OUT
IR-ACKNOWLEDGED
IR-REC EIVED
DIAGNOSTICS
CODE
IR-REC EIVER
Straps on module level :
Floating or non-floating input.
Red : J3 : strap "yes" : non floating strap "no" : floating
Green :J4 : strap "yes" : non floating strap "no" : floating
Blue : J5 : strap "yes" : non floating strap "no" : floating
H/C : J6 : strap "yes" : non floating strap "no" : floating
V : J7 : strap "yes" : non floating strap "no" : floating
Factory preset : strap "yes", non floating input
Sync selection.
J8 : separate sync or sync on green.
Factory preset : separate sync.
J3
Non-Floating
Floating
J8
J5
Sync selection
Sync on green
J6
Separate sync
J4
Floating or non floating input
J7
Connecting a computer, e.g. IBM PC (or
compatible), Apple Macintosh to the RS 232 input
of the projector.
The projector has a RS232 port that allows it to communicate with a
computer.
Applications : remote control and VISION communications.
a) remote control :
- easy adjustment of projector via IBM PC (or compatible) or MAC connection.
- allow storage of multiple projector configurations and
set ups.
- wide range of control possibilities.
- address range from 0 to 255.
b) VISION communications :
- sending VISION to the projector or copying the VISION from
the projector to a hard memory device.
Set up of the baud rate for communication with a
computer.
The communication speed between projector and computer, e.g. PC
or MAC, has 8 possible speeds. With DIP switches S2(1,2,3) on the
controller unit, it is possible to select the baud rate (communication
speed).
Gaining access to the DIP switches
Power down the projector and unplug the power cord from the wall
outlet.
Turn both lock screws with a screwdriver or coin counter clockwise.
Lift up and pivot the top cover. Attention : the cover is not secured
with an incorporated support. When opening, turn it over slowly
and lay it down on the second part of the top cover.
The processor module with the DIP switches is located on top, the
front left side (seen from the front of the projector, see next page).
5975348 BARCOVISION 8200 280497
6-7
Page 26
Connections
Loosen the locking Open the top cover
V
B
DIAGNOSTICS
CODE
IR-ACKNOWLEDGED
R
IR-RECEIVER
IR-RECEIVED
Processor module
This device complies with P art 15 of the FCC rules . Operation
is subject t o following two conditions :
(1) This device may not cause harm ful interference
(2) This device must accept any interference rec ei ved
including int erference that may cause undesi red operation
B
100 - 230 V
9 - 4 A
60 - 50 Hz
0
I
RS232 OUT
R
RS232 OUT
B
V
R
V
B
R
Baud rate switches
S2
3
V
IR-ACKNOWLEDGED
IR-RECEIVED
2
This device compli es with Part 15 of the FCC rules. Oper ation
is subject t o following two conditions :
(1) This device may not cause harmful interference
DIAGNOSTI CS
(2) This device must accept any interference receiv ed
including int erference that may cause undesired operation
CODE
IR-RECEIVER
100 - 230 V
9 - 4 A
60 - 50 Hz
0
I
1
S1
Baud rate setting
baud rate S2/1 S2/2 S2/3
9600 OFF OFF OFF
4800 ON OFF OFF
2400 OFF ON OFF
1200 ON ON OFF
600 OFF OFF ON
300 ON OFF ON
150 OFF ON ON
75 ON ON ON
Change the position of the DIP switches with a small screwdriver.
If all switches are in the correct position, close the top cover and
secure it by turning the lock screw clockwise. Connect the power
cord to the wall outlet and switch on the projector.
Connecting a RCVDS 05 to the projector.
- Up to 10 inputs (20 when video inputs) with the RCVDS 05 and 90
inputs when RCVDS's are linked via the expansion module.
- Serial communication with the projector.
- Remote control buttons on the RCVDS to control the projector
(source selection and analog settings).
- The selected source number will be displayed on a 2 digit display
and the selected input module will be indicated with a LED on the
rear.
For more information about the use of the RCVDS 05, consult the
owner's manual, order number : R5975765.
Connecting a VS05 to the projector
The VS05 can switch up to 5 Composite Video sources, 3 Super
Video sources and 1 RGB analog or component video source to the
projector. In addition, the audio signal proper to the source, can be
switched to an audio amplifier.
Order number : R9827890
For more information about the use of the VS05, consult the VS05
owner's manual, BARCO order number : R5975245.
Connecting an IR Remote Receiver 800 to the
projector.
This infrared red receiver unit makes it possible to control the
projector from another room.
There is a communication line cable between the IR receiver and the
projector or the RCVDS. The control information from the RCU can
now be sent to the IR Remote Receiver 800.
The IR Remote Receiver 800 displays the selected source on a 7segment display.
Order number : R9827515.
Screen
Projection room
Communication cable
IR Remote Receiver 800
Projector
Control room
6-8 5975348 BARCOVISION 8200 280497
Page 27
Controlling
0
9
7
8
65
43
21
RCU
Ceiling
Front of projector
IR sensor
0
9
7
8
65
43
21
RCU
Rear of projector
IR sensor
Table
100 - 230 V
9 - 4 A
60 - 50 Hz
RS232 OUT
0
I
IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOSTICS
CODE
IR-RECEIVER
7
CONTROLLING
The projector can be controlled with
a. The RCU
b. The hardwired RCU (cable is not included)
c. The local keypad.
Controlling the projector with the RCU and the hardwired RCU is
equal.
How to use the RCU?
a) Point the front of the RCU to the reflective screen surface.
Ceiling
IR sensor
Screen
c) Point the front of the RCU directly at one of the IR sensors of the
projector.
b) RCU used in a hardwired configuration.
This devi ce complies with Part 15 of the F CC rules. Operation
100 - 230 V
is subject to follow ing two condi tions :
(1) Th i s device m ay n ot cause har m f ul inter ference
9 - 4 A
(2) Th i s device m us t accept an y interf er ence recei v ed
I
0
RS232 OUT
includ i ng inter ference th at may cause u ndesired o peration
60 - 50 Hz
IR-ACKNO WLED GE D
DIAGNOSTI CS
CODE
IR-RECEIVER
IR-RECEIVED
RCU
When using the wireless remote control, make sure you are within the
effective operating distance (30m, 100ft in a straight line). The
remote control unit will not function properly if strong light strikes the
sensor window or if there are obstacles between the remote control
unit and the projector IR sensor.
Projector address
a. hardware set up of the projector address.
Every projector requires an individual address between 0 and 255
which is set with hardware DIP switches. To change that address, it
is necessary to first open the top cover (see Gaining access to the
DIP switches under Connecting to a computer.).
8 DIP switches (S1) are provided on the CPU module. Each DIP
switch has its own decimal value (ON='1', OFF = '0'). The summary
of the values associated to those DIP switches gives the address
S1
Projector address
Plug one end of the remote cable in the connector on the bottom of
the RCU and the second side in the connector in the front panel of the
projector labelled 'REMOTE'.
5975348 BARCOVISION 8200 280497
7-1
Page 28
Controlling
switch value
11
22
34
48
516
632
764
8 128
Example : address 83
DIP switch 1 2 3 4 5 6 7 8
setting 1 1 0 0 1 0 1 0
Summary : 1x1 + 1x2 + 0x4+ 0x8+ 1x16 + 0x32 + 1x64 + 0x128 = 83
b. How to control the projector or projectors.
The projector's address may be set to any value between 0 and 255. When the address
is set, the projector can be controlled now :
- RCU for addresses between 0 and 9.
- computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and
255.
Note : A projector will respond to a RCU set to an address of '0' regardless of what
address is set in the projector itself.
c. Using the RCU.
Before using the RCU, its is necessary to enter the projector address into the RCU (only
when that address is between 1 and 9). The projector with the corresponding address
will listen to that specific RCU.
When address 0, 'zero address' is programmed into the RCU, every projector, without
exception will listen to the commands given by this RCU.
How to display a projector address?
Press the ADDRESS key (recessed key on the RCU) with a pencil. The projector's
address will be displayed in a 'Text box'. This text box disappears after a few seconds.
To continue using the RCU, it is necessary to enter the same address with the digit
buttons (address between 0 and 9). For example : if the Address key displays projector
address 003, then press "3" digit button on the RCU to set the RCU's address to match
the projector's address. Do not press digit 003. This will address the remote to '0' and
control all projectors in the room.
How to program an address into the RCU?
Press the ADDRESS key (recessed key on the RCU) with a pencil and enter the address
with the digit buttons. That address can be any digit between 0 and 9.
When programming '0', zero address, the RCU will control any projector regardless of
the projector's address. This feature allows multiple projectors with different addresses
to be controlled by a single RCU.
Picture controls with direct access.
When an image control is pressed, a text box with a bar scale, icon and function name
of the control, e.g. 'brightness...' appears on the screen (only if text is ON). See example
screen. The length of the bar scale and the value of the numeric indication indicate the
current memorized setting for this source. The bar scale changes as the + or - buttons
of the control on the RCU are pressed or the + or - buttons on the local keypad.
PROJECTOR ADDRESS
001
BRIGHTNESS
0
63
7-2 5975348 BARCOVISION 8200 280497
Page 29
Brightness Control
Controlling
A correct
'brightness'
setting is important for good image reproduction.
Use the + button for a higher brightness.
Use the - button for a lower brightness.
Contrast Control
A correct 'contrast' setting is important for good image reproduction.
Adjust the contrast to the level you prefer, according to room lighting
conditions.
Use the + button for a higher contrast.
Use the - button for lower contrast.
Color Saturation
Color saturation is only active for Video and S-Video. Adjust the color
intensity of the picture.
Use the + button for richer colors.
Use the - button for lighter colors.
Tint Control
Tint is only active for Video and S-Video when using the NTSC 4.43
or NTSC 3.58 system.
Use the + button
Use the - button.
Sharpness Control.
Use the + button for a sharper picture.
Use the - button for a softer picture.
Phase Control
Use the control stick to adjust the phase.
How to get source information?
The projector can give information about its input configuration
(inserted modules and 800 peripherals connection) in a menu box.
To get this information, call the
key.
Highlight
press
System Settings
ENTER to select this option. The System Settings menu will
be displayed on the screen.
Highlight
Input Slots
by pushing the control disk up or down and press
ENTER to select.
The projector's controller will scan the input slots and displays the
result in the
Input Slots
Next to the digits you find the name of input slots. The controller starts
counting from left to right when you are in front of the projector and
looking to the lens.
If a RCVDS (switched on) or VS05 is connected to the projector, it will
be also indicated on the menu by adding
peripheral indication is made on the menu, there are still two possibilities :
- no RCVDS or VS05 connected or
- RCVDS is switched off.
When a 800 peripheral is connected to the projector, the input slots
are not accessible with the up or down arrow key to toggle their
function.
Main
menu by pressing the ENTER
by pushing the control disk up or down and
menu.
+ 800 peripheral
. If no 800
MAIN MENU
Picture Cont r ol
Audio Control
System Settings
File service
Service Mode
SYSTEM SETTINGS
Lamp Control : 1500W
Installation
Input slots
Summary
Color
832b
INPUT SLO T S
1. RGB-SS [CV]
2. RGB-SOG
3. Video/S-Video [Video]
•
4. Component video-SS
+ 800-peripheral
837
If an input slot is empty, the indication
corresponding slot number in the
no module
input slots
EXIT : returns to the System Settings menu.
5975348 BARCOVISION 8200 280497
is added next to the
menu.
7-3
Page 30
Controlling
How to get a summary of your projector?
The Summary gives an overview of :
- type of projector
- soft version
- lamp run time
- projector run time
- address
- installation configuration
- baud rate
- projector serial number
- lamp serial number
To display the Summary on the screen, press
Main
menu. Push the control disk up or down to highlight
Settings
and press ENTER to display the
Push the control disk up or down to highlight
ENTER. The summary will be displayed on the screen.
The following information is displayed :
-
type
of projector : BARCOVISION 8200
-
software version
ENTER to start up the
System Settings
Summary
System
menu.
and press
MAIN MENU
Picture Control
Audio Control
System Settings
File service
Service Mode
SYSTEM SETTINGS
832b
Lamp Control: 1500W
Installation
Input slots
Summary
Color
-
Address
: to change the address of the projector, see Projector
Address above in this chapter.
-
Installation
: possible installations :
* Front/Ceiling
* Front/Table
* Rear/Ceiling
* Rear/Table
To change the installation configuration follow the instructions in
chapter Installation Set Up.
-
Baud rate
: transfer speed for communication with a IBM PC (or
compatible) or MAC. The baud rate of the projector must be the
same as the baud rate of the connected computer. When there is
a difference, consult Set up of the baud rate for communication with
a computer in chapter Connections.
-
Projector Run Time
: gives the total run time since the first start up.
All projectors leave the factory with a run time of approximately 24
hours.
-
lamp run time
: the total time the lamp has been used since it was
installed in the projector.
Attention : the total lifetime of the lamp for a safe operation is 1000
hours maximum. Do not use it longer. Always replace the lamp with
an original BARCO lamp kit.
-
Projector Serial number
: indicates the fabrication number of the
projector. This number can be useful when calling for technical
assistance.
SUMMARY
Type : BARCOVISION 8200
Soft version : 1.00
Address : 1
Installation : front/ table
Baudrate : 9600
Projector run time : 104 h
Lamp run Time : 104 h
Projector Serial Number : 1012123
Lamp Serial Number : 0111111
-
Lamp Serial number
: indicates the fabrication number of the lamp.
This number can be useful when calling for technical assistance.
7-4 5975348 BARCOVISION 8200 280497
Page 31
Source Set Up
8
SOURCE SET UP
Input selection
Use the numeric keys on the RCU or use the local key pad to select the corresponding input
slot.
The source settings has to be installed for each source when these sources are displayed for
the first time.
Installation of the settings for a input source.
Start up the adjustment mode by pressing ENTER. The main menu will be displayed.
Push the joy stick key forward or backward to highlight File service.
ENTER selects the highlighted item and continues to the next step. EXIT returns always to the
previous step.
* Select the LOAD function to install the correct file. Only the files which can be used for this
source will be shown. (See appendix A for a list of the standard available files).
File annotation :
xxxxxxxx.xxx (Sx, xxxXxxxi)
I or blank : i = interlaced, blank = not interlaced
xxxXxxx : active pixel rating
MAIN MENU
Picture Control
System Settings
File service
Servic e Mode
832c
Sx : source number
xxx : file extension, first character is C (for custom made files) or S (for standard
files).
The second and third character is used for a following number (=file index)
file index for custom files : 00 to 63.
xxxxxxxx : base name, 8 characters.
The projector leaves the factory with different custom files installed.
Push the control disk up or down to select LOAD and press
menu.
The Load menu displays the corresponding files depending on the installed search pattern.
This search pattern can be "Fit" or "All". To change the search pattern, push the control disk
to the right to select "search pattern" and press ENTER to change the annotation between
brackets.
"All" : all available files will be displayed.
"Fit" : only the best fitting files will be displayed (with a distinction of ± 2 lines and line duration
distinction of ± 300 ns)
ENTER to display the Load
FILE SERVICE
Load
Edit
Rename
Copy
Move
Delete
Options
LOAD FILE
pal .s1 (s1. 675x278i)
pal .c50 (s1. 675x278i)
secam .s3 (s3. 675x278i)
pal .c50 (s1. 675x278i)
Search pattern : [Fit]
847
5975348 BARCOVISION 8200 210497
849
8-1
Page 32
Source Set Up
Push the control disk up or down to select the most fitting file and press ENTER to select.
When scrolling through the files, the image will be adapted according the settings of the
selected file (on line adaptation). When the best fitting image is displayed, press
ENTER
to select this file. A loading message with the selected file name will be displayed during
the installation of the selected file.
If the displayed image is not yet as it has to be, select the most corresponding file and go
to the Edit menu to change the file settings.
The actual active file is displayed on the second last line of the Load menu.
Edit file
The Edit file menu makes it possible to change the settings of the file
according to the real settings of the connected source. Consult the
source specification before entering the VISION.
To start up the EDIT menu, push the control disk up or down to select
EDIT in the FILE menu and press
ENTER.
Select the file which must be edited (mostly the active file) and press
ENTER.
The following selection menu will be displayed.
Read only
read/Write
FILE SERVICE
Load
Edit
Rename
Copy
Move
Delete
Options
EDIT FILE
pal .s1 (s1. 675x278i)
pal .c50 (s1. 675x278i)
secam .s3 (s3. 675x278i)
847c
Read only
Read/Write
: the settings can be changed but will not be saved.
: the settings are displayed and changes can be made
and saved.
Push the control disk up or down to select and press
ENTER.
The Edit file adaptation menu will be displayed.
The file name will be displayed in the upper right corner.
The following items can be adjusted :
Total quantity horizontal pixels
Active quantity horizontal pixels
Horizontal shift in pixels
Horizontal period in µs (is automatically adapted during the installation of a file with LOAD)
Total vertical lines (is automatically adapted during the installation of
a file with LOAD)
Active vertical lines
Vertical shift in lines
Interlaced : toggle on/off (is automatically set to its correct position
during the installation of a file with LOAD)
All settings can individually be changed (in video and S-video,
horizontal total pixels cannot be changed). Push the control disk up
or down to select an item. The color of the selected item will change
and follow one of the three methods to change the value.
a. press
ENTER to activate the digits and enter directly with the
numeric keys on the RCU or local keypad the new value or
b. press
ENTER to activate the digits. Push the control disk to the
right or to the left to select the changing digit. Push the control disk
up or down to scroll to desired digit. When finished press
ENTER to
confirm.
c. counting up or down by pushing the control disk to the right or to
the left.
To have a better view during an adjustment of the 'active' file, select
"Horizontal"
or
"Vertical"
by pushing the control disk up or down and
press ENTER.
A full image is displayed with the settings on the left side.
To change the values, highlight (color change) first the changing
value by pushing the control disk up or down and continue by pushing
the control disk to the left or to right to count up or down.
pal .c50 (s1. 675x278i)
EDIT FILE
pal .s1 (s1. 675x278i)
pal .c50 (s1. 675x278i)
secam .s3 (s3. 675x278i)
pal .c50 (s1. 675x278i)
EDIT FILE
Horizontal
Total 864 pixels
Active 675 pixels
Shift +114 pixels
Period 63.7 µs
Vertical (field)
Total 312 lines
Active 278 lines
Shift +21 lines
Interlaced [on]
Read AMDS
Options
Read Only
Read/Write
pal .c50
856
857
851
8-2 5975348 BARCOVISION 8200 210497
Page 33
Source Set Up
How finding the correct values for the displayed item?
During the installation of a file with LOAD, the horizontal period, the
total number of vertical lines and the interlaced mode are automatically measured and filled in in the menu table. These values will be
available when starting up the EDIT procedure of an active file.
Select first
If the value for
"Horizontal"
and press ENTER to display a full image.
"Horizontal total pixels"
is wrong, sampling mistakes
(small vertical bars in the projected image) will be seen in the image.
Select "Total" and adjust the pixel quantity. Adjust for zero bars (hint
: if the number of bars increase, adjust in the other way).
The active pixels : determine the width of the window on the screen.
This value is normally given in the source specifications. If not, adjust
until full image is displayed (no missing pixels).
Horizontal shift : to shift the image on the screen.
Horizontal period : already filled in with the correct value when active
file.
Press
EXIT to return to the normal Edit file menu.
Select
"Vertical"
by pushing the control disk up or down and press
ENTER. The full image is displayed.
The
"Vertical Total lines"
are already filled when an active file is
selected to be edited.
The
"Active lines"
: number of horizontal lines determining the height
of the projected image. This value is normally given in the specification of the source. If not, adjust until full image height is displayed (no
missing lines)
EDIT FILE (Horizontal)
Total :
865 pixels
Active :
675 pixels
Shift :
116 pixels
Period :
63.7 µS
EDIT FILE (Horizontal)
Total :
865 pixels
Active :
675 pixels
Shift :
116 pixels
Period :
63.7 µS
EDIT FILE (Vertical fi eld)
Total :
312 lines
Active :
278 lines
Shift :
+15 lines
Interlaced :
[On]
862
863
Vertical shift
: shift the image up and down (push joy stick forward or
backward) on the screen until the correct image position is obtained.
Interlaced [On] or [Off]
: this selection is automatically filled when
active file has to be edited. If the image is wrong due to
mismeasurement, use the ENTER key to toggle between [On] and
[Off]. (for interlaced images, 1 frame contains 2 fields).
Read AMDS
AMDS = automatic mode detection & synchronisation
During the installation of a file with LOAD, the system measured
automatically the horizontal period, the total vertical lines and the
interlaced mode.
When selecting Read AMDS, the system remeasures the above
indicated items.
Options
Source number
: The source number of a non-active source can be
changed to any other source number. This makes it possible to
create already a file for future source numbers.
Clamping
: the clamping determines the black level of the signal.
default setting : arrow up 1
Arrow up : trailing edge of the sync pulse to start the clamp pulse.
Arrow down : leading edge of the sync pulse to start the clamp pulse
1 : narrow clamp pulse
2 : wide clamp pulse
Field polarity inverted
: default [No]
This function is used for interlaced images. Both rasters of the image
could be shifted in a wrong way (double lines are visible in the image).
This can be corrected by inverting the field polarity to [yes].
EDIT FILE OPTIONS
Source number 1
Clamping [ 1]
Field polarity inverted [no]
Vertical refresh [sync]
Vertical sync polarity
[ ]
864
858
5975348 BARCOVISION 8200 210497
8-3
Page 34
Source Set Up
Vertical refresh [sync/async]
: The way of updating the image
information on the LCD panels.
* For sources with a vertical frequency up to 60 Hz : the vertical
refresh rate is the same as the vertical frequency of the incoming
source. This is a necessity to project moving images without 'motion
artefacts'. For stationary images with a vertical frequency up to 60 Hz
it is still possible to use asynchronous refresh. When loading Pal,
Secam, NTSC-files syncronous mode is default, for all other sources
below 60 Hz asyncronous mode is default.
* For sources with a vertical frequency higher that 60 Hz : the vertical
refresh is different than the vertical frequency of the incoming source.
Synchronous refresh cannot be used.
Vertical sync polarity
: Vertical refresh can be synchronised with the
leading sync edge [arrow down] or trailing sync edge [arrow up].
Press
EXIT to leave the Edit File Option menu.
Press
EXIT to leave the Edit menu. A confirmation menu will be
displayed (only when the file is opened as "Read/Write").
"Save changes to file "filename.ext" ?
yes or no.
Use the control disk to select yes or no and press
ENTER.
Rename
To change the name of a selected file to the name given in the TO
area.
Use the control disk to select RENAME and press
rename menu will be displayed.
Use the control disk to select a file name in the left part of the menu
and press
ENTER to select. This file name will be written in the FROM
area and the TO area. The TO area is active.
Press
ENTER to select the separate characters. Push the control
disk to the right or to the left to select the desired character. Change
that characters by pushing the control disk up or down. Numeric
characters can be entered directly with numeric keys on the RCU.
Press
ENTER to select Ok.
Press
ENTER for OK. The renamed file is entered in the list of files.
Press EXIT to leave the Rename menu.
ENTER. The
FILE SERVICE
Load
Edit
Rename
Copy
Move
Delete
Options
RENAME FILE
pal .s1
pal .c50
secam .s3
pal .c50
From :
......... c..
To
......... c..
OK
847d
Copy
To copy a selected file to the file with the name and extension given
in the TO area.
Use the control disk to select COPY and press
menu will be displayed.
Use the control disk to select a file in the list of files in the left part of
the menu and press
ENTER to select. This file name will be written
in the FROM area and the base name of the selected file in the TO
area. The file index in the TO area will be an unused file index. The
TO area becomes active. Press
ENTER to select the separate
characters. Push the control disk to the right or to the left to select the
desired character. Change that character by pushing the control disk
up or down (digits can be entered directly using the numeric keys).
Press
ENTER to select Ok.
Press
ENTER for OK. The copied file is entered in the list of files.
EXIT to leave the Copy menu (note : if the file index is changed
Press
to an existing index, a confirmation menu will be displayed).
ENTER. The copy
FILE SERVICE
Load
Edit
Rename
Copy
Move
Delete
Options
COPY FILE
pal .s1
pal .c50
secam .s3
pal .c50
From :
......... c..
To
......... c..
OK
852
847e
853
8-4 5975348 BARCOVISION 8200 210497
Page 35
Move
To move a selected file to the file with the name and extension given
in the TO area.
Use the control disk to select MOVE and press
ENTER. The move
menu will be displayed.
Use the control disk to select a file in the list of files in the left part of
the menu and press ENTER to select. The selected file will be written
in the FROM area and the base name in the TO area. The file index
in the TO area will be an unused index. The TO area becomes active.
Press
ENTER to select the separate characters. Push the control
disk to the left or to the right to select the desired character. Change
that characters by pushing the control disk up or down (digits can be
changed directly with the numeric keys).
Press
ENTER to select Ok.
Press
ENTER for OK. The moved file is entered in the list of files
(note: if the file index is changed to an existing index, a confirmation
menu will be displayed).
Press EXIT to leave the move menu.
Delete
To delete a selected file out of the list of files.
Use the control disk to select DELETE and press ENTER. The delete
menu will be displayed.
Push the control disk up or down to select a file and press ENTER.
The selected file is written in the Delete area and the OK button is
active. Press
A confirmation menu "Delete file 'file name'?" is displayed. When you
want to delete the file, select Yes by pushing the control disk to the
left or to the right and press
file, select No and press ENTER.
Note : the active file cannot be deleted.
ENTER
to delete the file.
ENTER. If you do not want to delete the
FILE SERVICE
Load
Edit
Rename
Copy
Move
Delete
Options
MOVE FILE
pal .s1
pal .c50
secam .s3
pal .c50
FILE SERVICE
Load
Edit
Rename
Copy
Move
Delete
Options
DELETE FILE
pal .s1
pal .c50
secam .s3
pal .c50
Source Set Up
847f
From :
......... c..
To
......... c..
OK
847g
Delete :
......... c..
OK
854
Options
Use the control disk to select OPTIONS and press ENTER. The
Options menu will be displayed.
The list of files can be given only by name and extension (file details
OFF) or with full details (file details ON).
example :
file details [Off] pal .c50
file details [On]
pal .c50 (S1. 675x278i)
The list of files in the different File menus can be sorted by file name
(file sort [name]) or by file extension (file sort [index]).
Select the options by pushing the control disk up or down and press
ENTER to toggle the option.
FILE SERVICE
Load
Edit
Rename
Copy
Move
Delete
Options
FILE OPTIONS
File Details [On]
File sort [Name]
865
847h
866
5975348 BARCOVISION 8200 210497
8-5
Page 36
Source Set Up
8-6 5975348 BARCOVISION 8200 210497
Page 37
Picture Control in Adjustment Mode
9
PICTURE CONTROL IN ADJUSTMENT MODE
The picture control menu is split up in two parts :
Signal operations
and
Screen operations.
Signal operations
Screen operations
Signal operations.
Select first the Picture Control menu on the Main menu by pushing
the control disk up or down.
Press
ENTER to select.
Push the control disk up or down to select Signal Operations.
The default setting for all items are shown in the menu next to this text.
To change a value in the Signal Operation menu, select first the item
by pushing the control disk up or down and follow then one of the two
following methods :
a. direct access, with the numeric keys on the RCU or local keypad.
b. scrolling by pushing the control disk to the right or to the left until
the desired value (image quality) is obtained.
: to manipulate the video signal, e.g. sync slow/fast, color balance adjustment etc.
: to manipulate the projection window and the picture, e.g. shift, stretch, enlarge and reduce.
MAIN MENU
Picture Control
System Settings
File service
Servic e Mode
PICTU RE CONTRO L
Signal oper ation
Screen oper ation
832a
SIGNAL OPERATIONS
Video offset 128
Gain
Gain red 160
Gain green 160
Gain blue 160
Gamma 1.0
Smoothness 4
Still Video [Off]
Sync [Slow]
Color balance
860a
859
Video offset
Default value : 128
To adjust the Video offset, be sure the contrast level is adjusted to "48"
(brightness setting has no influence) and the color saturation is set to
zero (for video). When possible use a grey scale test pattern. Adjust
until the second last bar (dark grey) is distinguishable from the last bar
(black).
Gain
Default value : 160
To adjust the Gain, be sure the contrast level is adjusted to "48".
When possible use a grey scale test pattern. Adjust until the first white
bar is distinguishable from the second white bar.
5975348 BARCOVISION 8200 210497
861
861
9-1
Page 38
Picture Control in Adjustment Mode
Gain adjustment per color
If the obtained color balance is not yet correct, adjust with the separate
gain controls until the desired color balance is obtained.
Smoothness
The lower the smoothness value, the sharper the image. The
influence of this setting is visible on high density image with small
characters.
Still video [On/Off]
This function is only used for stationary interlaced images.
Highlight Still Video by pushing the control stick forward or backward
and press
ENTER to toggle between ON and OFF.
Still Video [On] : the displayed image contains less jitter and gives a
sharper image.
Still Video [Off] : for moving pictures.
Sync [Fast/Slow]
Highlight Sync by pushing the control disk up or down and press
ENTER to toggle between Slow and Fast.
Note : Sync is normally used in the SLOW position. The FAST
position is used to compensate for unsteady sync pulses from older
video playback equipment.
Color Balance
Highlight Color Balance by pushing the control disk up or down and
ENTER to select the color balance selection menu.
press
The next choices are possible :
3200K
6500K
9500K
Custom
Use the control disk to make your selection and press
A marker indicates the actual color balance setting.
When custom is selected, the blue and red color can be adjusted
(range from 0 to 2.5) in comparison with the green color (value 1).
Push the control disk up or down to select blue or red. Push the
control disk to the left or to the right to adjust.
ENTER.
SIGNAL OPERATIONS
Video offset 100
Gain
Gain red 200
Gain green 200
Gain blue 200
Gamma 1.0
Smoothness 4
Still Video [Off]
Sync [Slow]
Color balance
Tc = custom
G
R
B
1.03
1.01
3200
6500
9500
Custom
859
9-2 5975348 BARCOVISION 8200 210497
Page 39
Screen operations
870870
870
870
Picture Control in Adjustment Mode
Select the
Picture Control
menu on the Main menu by pushing the
control disk up or down. Press ENTER to select.
Push the control disk up or down to select
Screen operations
. Press
ENTER to select.
When pushing continuously on the control disk, the adjustment will
be executed in an accelerated fashion.
Zoom/pan
Push the control disk up or down to highlight
ENTER to select.
All functions, e.g. move, enlarge, reduce, stretch, can be done on a
"Window"
or on a
"Picture"
.
Zoom/Pan
and press
MAIN MENU
Picture Control
System Settings
File service
Service Mode
PICTURE CONT ROL
Signal operation
Screen operation
SCREEN OPERATIONS
832a
SCREEN OPERATIONS
Zoom/Pan
Geometry (off)
Configure
Zoom/Pan
Geometry (off)
Configure
860b
867
Window
A window determines the maximum area used on the screen to
project a picture.
This window can be placed in any position on the screen using the
move, reduce and stretch controls. During a first start up, the window
will be on its maximum dimensions. Enlarging and moving is not
possible in this maximum position.
Use the following controls to create a desired window on the screen.
With these functions, all aspect ratios are possible.
Select the controls by pushing the control disk to the right or to the left
and press
ENTER to activate the control.
[window]
[window]
868a
Screen
Window
Picture
870
moves the window to the left.
5975348 BARCOVISION 8200 210497
moves the window to the right.
9-3
Page 40
Picture Control in Adjustment Mode
[window]
[window]
[window]
moves the window upwards
moves the window downwards
stretches the window in the
horizontal direction.
870
870
870
870
[window]
[window]
[window]
Compresses the window in
the horizontal direction.
stretches the window in the
vertical direction.
compresses the windows in
the vertical direction.
870 870
870
870
870
870
870
870
[window]
enlarges the window, both
of horizontal and vertical directions simultaneously.
870
870
9-4 5975348 BARCOVISION 8200 210497
Page 41
870
870
[window]
[window]
Picture
The picture can be moved, enlarged, reduced within a created window.
[picture]
Displays the covered info on the
left side.
(you have to consider that you
are moving your camera to the
left side).
Picture Control in Adjustment Mode
reduces the window, both of
horizontal and vertical directions simultaneously.
reset button, brings the window
to its maximum dimensions.
[picture]
[picture]
[picture]
Displays the covered info on the
right side.
Displays the covered info on the
top side .
Displays the covered info on the
bottom side.
5975348 BARCOVISION 8200 210497
[picture]
Stretches the picture in the
horizontal direction.
9-5
Page 42
Picture Control in Adjustment Mode
[picture]
Compresses the picture in
the horizontal direction.
[picture]
Stretches the picture in the
vertical direction.
[picture]
[picture]
[picture]
[picture]
Compresses the picture in
the vertical direction.
Zooms in the picture, both
horizontal and vertical directions simultaneous
Zooms out the picture, both
horizontal and vertical directions simultaneous
Reset button, brings the picture to its maximum dimensions within the created window.
9-6 5975348 BARCOVISION 8200 210497
Page 43
Configure
Picture Control in Adjustment Mode
The configure menu contains two toggle functions :
conversion
Use the control disk to select
.
Configure
and press ENTER.
geometry
and
Conversion
All incoming signals are internally converted to be displayed at its
maximum possible dimensions. When conversion is [off], the real
input signal is displayed on the screen. Parts of the image cannot be
displayed and will be lost.
When conversion is [off], the geometry function is disabled.
Geometry
The Geometry function can only be activated when conversion is
[on].
Use the Geometry adjustment to align the image if the projector is
mounted under a non standard projection angle.
If the Geometry function has to be adjusted, toggle Geometry to [On]
with the
ENTER key and press EXIT to return to the
tions
menu (previous menu).
Screen Opera-
SCREEN OPERATIONS
Zoom/Pan
Geometry (off)
Configure
CONFIGURE
Conversion [On]
Geometry [Off]
CONFIGURE
Conversion [On]
Geometry [Off]
868b
874
Highlight
Geometry
will be displayed.
and press ENTER to select. The geometry menu
SCREEN OPERATIONS
Zoom/Pan
Geometry
Configure
874
868c
875
5975348 BARCOVISION 8200 210497
9-7
Page 44
Picture Control in Adjustment Mode
Enlarge the upper part of the
projected image in horizontal
way.
Reduce the upper part of the
projected image in horizontal way.
Enlarge the lower part of the
projected image in horizontal
way.
Reduce the lower part of the
projected image in horizontal way.
Reset, brings the image to a
squared image without distortion.
9-8 5975348 BARCOVISION 8200 210497
Page 45
Service Mode
SERVICE MODE
10
The service mode offers :
- test patterns such as convergence patterns (green, red on green, blue on green and hatch patterns).
- alignments for the decoder circuit such as luminance delay, comb filter, etc. (more info in service manual)
- modifying password
- resetting the lamp run time.
- lamp run time history.
- I²C Device test (more info in service manual)
To protect your settings made in the service mode, a password can be introduced. When the password function is activated, every time the
Service mode is selected, the service mode asks for your password before continuing.
How to activate the password function?
The password function can be hardware set with a DIP switch on the
CPU module. To change the position of this DIP switch, it is
necessary to open first the top cover (see Set up of the baud rate for
communication with a computer, chapter Connections).
When DIP switch 4 (S2) is in the :
- ON position, password is activated.
-OFF position, password not activated, service mode is free
accessible.
Password
off
on
Start up of the Service mode.
When in operational mode, press ENTER to display the
Use the control disk to highlight
If the password function is activated, the
pears on the screen.
Your password contains 4 digits. Enter the digits with the numeric
keys on the RCU or the local keypad.
Example : 2 3 1 9
For each digit entered, a 'X' appears on the screen under the
displayed text
When the entered password is wrong, the following message will be
displayed :
Press EXIT to return to the main menu.
When your password is correct, you gain access to the Service
menu.
'Enter password'
Invalid Password
Service mode
.
and press ENTER.
Enter password
main
box ap-
menu.
MAIN MENU
Picture Control
System Settings
File service
Servic e Mode
832d
SERVICE MODE
PASSWORD
Enter Password :
Error
Invalid Password
----
5975348 BARCOVISION 8200 210497
10-1
Page 46
Service Mode
Factory programmed password :
0000
Convergence adjustment of the LCD panels.
Every LCD panel has 6 adjustment screws. By turning these screws
you change the relative position of the panels and converge the
image.
Always start with the adjustment of the green panel. When the green
image is correctly focused, it will later on be used as the reference
image to converge the red and blue image.
Next alignments have to be done :
You have to adjust the green panel until the indicated lines on the
screen are focused (sharp lines). Continue with the red panel and
adjust until the red lines coincide with the green lines. Than continue
with the blue panel until the blue lines coincide with the green lines.
Follow the next procedure to adjust the LCD panels.
* Open the top cover as described in
switches
under
Connecting to a computer
Gaining access to the DIP
in chapter
Connections
SERVICE MODE
Modify Password
Reset Lamp Run Time
Lamp Ru n Ti m e Hi st ory
Convergence
Display Se tt ings
Decoder Settings
Color Balance
I2C De vi c e Te s t
878
.
The three mounting parts for the LCD's (two are shown on the
drawing below) are located on the black metal cover. The screws are
indicated from 1 to 6 for each color.
Note : the space between the LCD panel in the green channel and the
field lens has to be 4 to 5 mm. Otherwise when projecting a black
image, a discoloring will be visible. (To project a black image, select
the internal pattern 'purity' and put all settings to '0')
To adjust the convergence, there are test patterns provided in the
service menu.
Use the control disk to hightlight
display the
Convergence
menu.
Convergence
and press ENTER to
Start with the Green test pattern and continue with the Red on green
and finish with the Blue on green.
Use the control disk to select
Green
and press ENTER to display the
green pattern.
SERVICE MODE
Modify Password
Reset Lamp Run Time
Lamp Run Time History
Convergence
Display Settings
Decoder Settings
Color Balance
I2C De vi c e Te s t
CONVERG EN CE
Green
Blue on Green
Red on Green
Hatch
878d
879
10-2 5975348 BARCOVISION 8200 210497
Page 47
The pattern shows lines of one pixel.
Near six lines on the displayed pattern, a screw is drawn with a
number next to it (e.g. if displayed in green = corresponding with the
screws and numbers on the green LCD panel).
When turning a screw in the direction marked by the arrow above the
displayed screw on the screen, the line on the screen moves in the
direction of the straight arrow.
Green focusing
a. Adjust the projection lens until optimum focus for the lines 5 and 6
is obtained.
b. Turn screw 4 for optimum focus of the corresponding green line 4
on the screen.
c. Turn screw 5 for optimum focus of the corresponding green line 5
on the screen.
d. Turn screw 6 for optimum focus of the corresponding green line 6
on the screen.
The three alignments influence each other, therefore repeat if necessary the above three steps (b,c and d).
When the green pattern is correctly focused, press EXIT to return to
the
Test pattern
menu.
Service Mode
4
1
6
3
4
1
6
3
5
2
5
2
Red on green convergence.
Use the control disk to hightlight
Red on green
and press ENTER to
display the Red on green test pattern.
The longest lines are the red lines. These lines must be converged
with the green lines.
The drawn screws and numbers are displayed in red.
Follow next steps :
a. Adjust first screws 4, 5 and 6 to obtain an optimum focus for
respective lines 4, 5 and 6.
Due to interaction, it may be necessary to repeat step a several times.
Follow next steps to converge the red lines with the green lines :
b. Start with screw 2 and adjust for optimal convergence of line 2.
c. Adjust screw 3 for optimal convergence of line 3.
Due to interaction repeat above two steps (b and c) if line 2 and
possibly line 3 is misaligned.
If both lines are correctly converged, continue with screw 4.
Adjust screw 4 until line 4 is correctly converged. It is possible that
line 2 and 3 have to be reconverged. If so, repeat procedure for screw
2 and 3 (step b and c)
If line 2, 3 and 4 are converged, continue with line 1 (screw 1).
CONVERGENCE
Green
Blue on Green
Red on Green
Hatch
879b
4
1
65
3
2
When line 1 is converged, check again the convergence of lines 2,
3 and 4. If necessary repeat the above procedure for the corresponding lines.
Check if lines 5 and 6 are correctly converged. If so, press EXIT to
return to the
Test pattern
menu and continue with Blue on green.
If not yet correctly converged, check the distance between lines 5
and 6 of the red pattern and the distance between lines 5 and 6 of the
green lines.
5975348 BARCOVISION 8200 210497
10-3
Page 48
Service Mode
Two possibilities :
1) distance between red lines is smaller than distance between green
lines.
Turn screw 5 and 6 clockwise until distance between lines 5 and
6 is the same for the red and green lines.
2) distance between red lines is greater than distance between green
lines.
Turn screw 5 and 6 counter clockwise until distance between lines
5 and 6 is the same for the red and green lines.
4
1
65
3
2
4
1
Due to this movement the lines 1, 2, 3 and 4 may be out of
convergence. Repeat the above mentioned steps for the respective
lines.
If all lines are correctly converged, press EXIT to return to the
pattern
menu.
Test
Blue on green convergence.
Use the control disk to highlight
Blue on green
and press ENTER to
display the Blue on green test pattern.
Repeat the same procedure as for Red on green lines but read blue
when red is indicated.
To check the result of the convergence adjustments, highlight
Hatch
and press ENTER. A hatch pattern will be displayed on the screen.
ENTER : displays a hatch pattern.
EXIT : returns to the service menu.
6
3
CONVERGENCE
Green
Blue on Green
Red on Green
Hatch
CONVERGENCE
Green
Blue on Green
Red on Green
Hatch
5
2
879c
879d
All lines must be displayed in white, if not so repeat the convergence
adjustment procedure.
10-4 5975348 BARCOVISION 8200 210497
Page 49
Modify password
Service Mode
To change your password, highlight
'Modify password'
and press
ENTER to start up the password modification procedure.
Enter your old password with the digit keys. After the fourth digit is
entered, the next modify password menu is displayed.
Your new password will be asked if your old password is correct.
Enter your new password with the digit keys. After the fourth digit, the
projector will ask to re-enter your new password.
Re-enter your new password.
When the password is correct, the message "Password modified" will
be displayed for a certain time and then the projector returns to the
Service menu.
When the password is not correct, an error message "Invalid password" will be displayed. Press EXIT to continue. The projector
returns to the Service menu without changing the password.
MODIFY PASSWORD
Enter New Pass word :
MODIFY PASSWORD
Enter Old Password :
----
MODIFY PASSWORD
Re-enter New Passwo rd :
----
----
Lamp Run Time History
To get an overview of the different lamp run times, highlight
Run time History
and press ENTER. A listing with the lamp serial
number and the corresponding run time will be displayed.
Reset Lamp Run Time.
Highlight
Reset Lamp Run Time
and press ENTER to select.
Lamp
SERVICE MODE
Modify Password
Reset Lamp Run Time
Lamp Run Time History
Convergence
Display Settings
Decoder Settings
Color Balance
I2C De vi c e Te s t
LAMP RUN TIME HISTORY
SERVICE MODE
> SN1425634 75 h
SN1234567 1000 h
SN0000000 0 h
SN0000000 0 h
SN0000000 0 h
SN0000000 0 h
Modify Password
Reset Lamp Run Time
Lamp Ru n Ti m e Hi st ory
Convergence
Display Se tt ings
Decoder Settings
Color Balance
I2C De vi c e Te s t
878c
5975348 BARCOVISION 8200 210497
878b
10-5
Page 50
Service Mode
When
Reset Lamp Run Time
the following warning will be displayed :
Risk of electrical shock. Reset lamp run time is reserved to qualified
service personnel.
If you are not qualified, press EXIT to cancel the reset operation.
is selected in the
Service Mode
menu,
WARNING
RISK OF ELECTRICAL SHOCK
------------------------------------------Reset lamp run time
is reserved to
qualified service personnel.
Press ENTER to continue;
Press EXIT to cancel operation
10-6 5975348 BARCOVISION 8200 210497
Page 51
STANDARD SOURCE SET UP FILES
A
Standard source set up files.
Standard preprogrammed set up files.
NAME RESOLUTION FVERT FHOR FPIX PTOT PACT LTOTLACT
Hz kHz MHz
Standard Source Set Up Files
Name :
name of file, contains the settings
Resolution : image resolution, when followed by ...I means interlaced.
CGA 640 X 200 59,924 15,700 14,318 912 640 262 200
NTSC 675 X 240I 29,970 15,734 13,500 858 675 263 240
NTSC_2 675 X 240I 29,970 15,734 13,500 858 675 263 240
PAL 675 X 278I 25,000 15,625 13,500 864 675 313 278
PAL_2 675 X 278I 25,000 15,625 13,500 864 675 313 278
SECAM 675 X 278I 25,000 15,625 13,500 864 675 313 278
SECAM_2 675 X 278I 25,000 15,625 13,500 864 675 313 278
EGA 640 X 350 59,702 21,851 16,257 744 640 366 350
MAC_5 512 X 342 60,158 22,259 15,670 704 512 370 342
MAC_3 512 X 384 60,147 24,480 15,667 640 512 407 384
MAC_4 560 X 384 60,147 24,480 17,234 704 560 407 384
8514-A 1024 X 384I 43,479 35,522 44,900 1264 1024 409 384
VGA_TXT 720 X 400 70,087 31,469 28,322 900 720 449 400
COMPUSC4 1024 X 480I 29,945 30,694 39,779 1296 1024 512 480
VGA_72V 640 X 480 72,800 37,856 31,496 832 640 520 480
FVERT Hz :
FHOR kHz :
source.
FPIX MHz :
PTOT :
PACT :
LTOT :
LACT :
vertical frequency of the source
horizontal frequency of the
pixel frequency
total pixels on one horizontal line
active pixels on one horizontal line
total lines in one frame
active lines in one frame
VGA_GR 640 X 480 59,941 31,469 25,175 800 640 525 480
VGA75ISO 640 X 480 75,000 39,375 31,500 800 640 525 480
MAC_2 640 X 480 66,667 35,000 30,240 864 640 525 480
MAC_LC 640 X 480 66,619 34,975 31,338 896 640 525 480
MUSE 960 X 518I 30,000 33,750 37,125 1100 960 563 518
HDMAC 1008 X 570I 25,020 31,250 39,125 1252 1008 625 570
SVGA_56V(*) 800 X 600 56,250 35,156 36,000 1024 800 625 600
SVGA_60V(*) 800 X 600 60,317 37,879 40,000 1056 800 628 600
SVGA_72V(*) 800 X 600 72,084 48,080 50,003 1040 800 667 600
(*) This source type will be displayed in a window of 756 x 756 pixels, no conversion.
5975388 BARCOVISION 9200 210497
A-1
Page 52
Standard Source Set Up Files
A-2 5975388 BARCOVISION 9200 210497
Page 53
BATTERY REPLACEMENT IN THE RCU
B
Battery replacement in the RCU.
Remove the battery cover on the backside of the remote control by
pushing the indicated handle a little to the bottom of the RCU. Lift up
the top side of the cover at the same time.
(fig. 1)
Remove the battery from the compartment and disconnect the
contact plate. (fig. 2)
Connect a new 9 V battery (E-block type, e.g. type 6F22S or
equivalent) to the contact plate.
Insert the battery back into the compartment.
Put the cover back.
Battery Replacement in the RCU
Contact
plate
Battery
310a.DRW
fig. 1
fig. 2
5975348 BARCOVISION 8200 210497
B-1
Page 54
Lenses
C
LENSES
Focusing the lens
Loosen the fastener ring of the lens by turning counter clockwise.
Focus the image by turning the lens barrel to the left or the right.
Attention : Do not turn out the lens too far, otherwise it will fall out of
the lens holder.
When the image is focused, secure the correct position of the lens
with the fastener ring by turning this ring clockwise.
Lens Cleaning Procedure
Cleaning procedure for HD(1.5-3:1) lens and HD(3-5.3:1) lens.
To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have developed recommendations for
cleaning the lens. FIRST, we recommend you try to remove any
material from the lens by blowing it off with clean, dry deionized air.
DO NOT use any liquid to clean the lenses.
A Toraysee
Proceed as follows :
1. Always wipe lenses with a CLEAN Toraysee
2. Always wipe lenses in a single direction. Do not wipe back and
forward across the lens surface as this tends to grind dirt into the
coating.
TM
cloth is included with the lens kit.
TM
cloth.
Lens holder
Fastener
Lens
ing exposed lens surfaces, we have developed recommendations
for cleaning lenses.
material from the lens by blowing it off with deionized air or
brushing it with a soft, camel's hair brush.
Plastic lens with multilayer coatings & all glass lens elements.
1.
DO NOT spray any type of fluid directly on the lens surface.
2.
DO NOT use any dry material to clean the surface (dry rag, tissue,
etc.)
3. Use a commercial liquid window cleaner.
aerosol.
or a 70-30 mixture of ethyl ether and ethyl alcohol may also be used.
If you are not sure of the cleaning agent, experiment with a small
area of the lens first.
Other cleaning agents, such as laboratory-grade acetone
FIRST, we recommend you try to remove any
lightly
DO NOT use an
3. Do not leave cleaning cloth in either an open room or lab coat
pocket, as doing so can contaminate the cloth.
4. If smears occur when cleaning lenses, replace the cloth. Smears
are the first indication of a dirty cloth.
5. Do not use fabric softener when washing the cleaning cloth or
softener sheets when drying the cloth.
6. Do not use liquid cleaners on the cloth as doing so will contaminate
the cloth.
Order number for a new Toraysee
Other lenses can also be cleaned safely with this Toraysee
Cleaning procedure for the other HD lens
To minimize the possibility of damaging the optical coating or scratch-
TM
cloth : R379058.
TM
cloth.
4. Use a soft cotton cloth (cotton diapers laundered several times to
remove sizing) or any soft facial tissue (Charmin, Softweve, etc.).
5. When using window cleaner,
lightly wipe the surface. Then lightly dry with a new tissue.
6. When using acetone or ethyl ether mixture, proceed as follows :
Fold the cloth or tissue several times to form a pad. Soak the folded
end of the pad in the acetone. Starting at the diameter opposite you,
immediately wipe the coated lens, with very little pressure, toward
you in a straight line and off the lens. Do not stop with the tissue on
the lens. Wipe at a speed that is equal to the evaporation rate. This
is very important to prevent streaking and spotting. Start your
wiping at one side of the lens and, with successive wipes, move to
the other side. Turn the pad over for each wipe, then inside out. Do
not make more than one wipe per clean area of pad. Be careful of
the painted edge, since acetone will soften it.
moisten the cloth or tissue
and
5975348 BARCOVISION 8200 210497
C-1
Page 55
Lenses
Lenses
This APPENDIX gives an overview of the tables and formulas for the available lenses for the projector.
The next lenses are available :
Name length lens diam. lens weight order number
mm (inch) mm (inch) kg (lbs)
HD(1.2:1) 253 (9.96) 189 (7.44) 8.7 (19.2) R9829200
HD(2.2:1) 235 (9.25) 137 (5.39) 7.5 (16.5) R9829060
HD(3.3:1) 149 (5.87) 152 (5.98) 4.3 (9.5) R9829075
HD(4.0:1) 165 (6.50) 152 (5.98) 3.5 (7.7) R9829145
HD(5:1) 238 (9.37) 164 (6.46) 5.1 (11.2) R9829180
HD(7:1) 373 (14.68) 196 (7.72) 12.0 (26.4) R9829090
HD(1.5-3:1) 460 (18.11) 260 (10.24) 13.0 (28.7) R9829150
HD(3-5.3:1) 578(22.8) 225(8.9) 15.0(33.1) R9829190
HD(0.9:1)* 366(14.4) 216(8.5) 10.0(22.0) R9829550
Lens formulas to calculate the projector distance.
HD(1.2:1) Metric PD=1.264 x SW + 0.126 + (0.018/SW)
HD(2.2:1) Metric PD=2.0566 x SW + 0.16 + (0.029/SW)
Inch PD= 1.264 x SW + 4.961 + (27.90/SW)
Inch PD=2.0566 x SW + 6.299 + (44.95/SW)
HD(3.3:1) Metric PD=3.33 x SW + 0.386 + (0.046/SW)
HD(4.0:1) Metric PD=4.02 x SW + 0.50 + (0.06/SW)
HD(5:1) Metric PD=5 x SW + 0.747 + (0.070/SW)
HD(7:1) Metric PD=6.911 x SW + 1.414 + (0.096/SW)
HD(1.5-3:1) Metric PDmin=1.49 x SW + 0.123
HD(3-5.3:1) Metric PDmin=3.126 x SW - 1.08 ± 0.2
HD(0.9:1) * Metric PD=0.83 x SW + 0.20 recommanded screen width range 1.2 m < SW < 3.20 m
Inch PD=3.33 x SW + 15.19 + (71.30/SW)
Inch PD=4.02 x SW + 19.69 + (93/SW)
Inch PD=5 x SW + 29.41 + (108.5/SW)
Inch PD=6.911 x SW + 56.06 + (148.8/SW)
PDmax=2.983 x SW + 0.145
Inch PDmin=1.49 x SW + 4.84
PDmax=2.983 x SW + 5.71
PDmax=5.345 x SW ± 0.2
Inch PDmin=3.126 x SW - 42.52 ± 8
PDmax=5.345 x SW ± 8
Inch PD=0.83 x SW + 7.874 47 inch < SW < 126 inch
* ON-AXIS lens, requires an on-axis projector or a retrofitted kit off -> on-axis (Ord. no. R808459K)
C-2 5975348 BARCOVISION 8200 210497
Page 56
Source Numbers 90 - 99
D
SOURCE NUMBERS 90 - 99
Source numbers 90 - 99
These source numbers do not correspond to physical inputs. They can only be used when the projector is equipped
with a RCVDS 05 or VS05. An additional adjustment file can be created for these source numbers. This file can
contain different settings. The relationship between sources 0 - 9 and 90 - 99 is shown in the diagram below.
source input 1
source input 2
source input 3
source input 9
Follow the steps below to create a second file for sources 0 to 9 :
source number 1
source number 91
source number 2
source number 92
source number 3
source number 93
source number 9
source number 99
file A
file A'
file B
file B'
file C
file C'
file I
file I'
1. Select the source between 0 and 9.
2. Select the corresponding source number between 90 and 99 with the digit keys on the RCU.
3. Enter the adjustment mode and load a corresponding file. Edit this file if necessary.
4. Save the file and exit the adjustment mode.
5975348 BARCOVISION 8200 210497
D-1
Page 57
P
RCU
INPUT SOURCES
1
PROJECTOR
RCVDS
2
3
4
5
6
1
2
3
5
6
7
8
9
10
INPUT SOURCES
7
P
RCU
INPUT SOURCES
1
PROJECTOR
RCVDS
2
3
4
5
6
1
2
3
5
6
7
8
9
10
INPUT SOURCES
7
INSERT CARD
Insert Card
5975348 BARCOVISION 8200 210497
"
Loading...