Barco R5976663-01, R9842060 User Manual

Page 1
TLD HB (1.6-2.0:1) Lens Kit
Installation Manual
R9842060
R5976663/01 22/12/2004
Page 2
Barco nv Events Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.89.70 Fax: +32 56.36.88.24 E-mail: events@barco.com Visit us at the web: www.barco.com
Barco nv Presentations
laan 5, 8520 Kuurne
Noord Phone: +32 56.36.82.11 Fax: +32 56.35.86.51
presentations.bid@barco.com
E-mail: Visit us at the web: www.barco.com
PrintedinBelgium
Page 3
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied w ar­ranties or merchantability and fitness for aparticularpurpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall n ot otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respecti All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufactures.
ve holders.
Page 4
Page 5
Table of contents
TABLE OF CONTENTS
1. TLD HB (1.6-2.0:1) Lens Kit....................................................................................... 3
1.1 Kit Contents .......................................................................................................................... 3
1.2 Removing the installed lens.......................................................................................................... 3
1.3 Installing the new lens ............................................................................................................... 4
1.4 Quick Lens Adjustment .............................................................................................................. 5
1.5 Lens Formulas........................................................................................................................ 6
1.6 Cleaning the lens..................................................................................................................... 7
R5976663 TLD HB (1.6-2.0:1) LENS KIT 22/12/2004
1
Page 6
Table of contents
2 R5976663 TLD HB (1.6-2.0:1) LENS KIT 22/12/2004
Page 7
1. TLD HB (1.6-2.0:1) LENS KIT
1.1 Kit Contents
Kit Contents
Contents
TLD HB (1.6-2.0:1) Lens.
Installation Manu al.
Toraysee
1.2 Removing the installed lens
What has to be done?
Removing the installed lens on the SLM series projector.
Necessary Tools
No tools necessary.
TM
Cloth.
1. TLD HB (1.6-2.0:1) Lens Kit
WARNING: Risk of personal injury. Instructions for lens installation must be followed thoroughly.
How to remove the installed lens?
To remove the lens, follow the next procedure:
1. Support the lens with one hand. (image 1-1)
2. Move the handle of the lens anchor system to the left. (image 1-2)
3. Take the lens unit out of the lens block. (image 1-3)
Image 1-1 Support the lens with one hand
R5976663 TLD HB (1.6-2.0:1) LENS KIT 22/12/2004 3
Page 8
1. TLD HB (1.6-2.0:1) Lens Kit
Image 1-2 Move the handleof the lens anchor system to the left
Image 1-3 Take the lens outof the lens block
1.3 Installing the new lens
What has to be done?
This new lens has to be installed on the SLM series projector.
Necessary Tools
No tools necessary.
WARNING: Risk of personal injury. Instructions for lens installation must be followed thoroughly.
How to install the new lens?
To install the lens, follow the next procedure:
1. Take the lens assembly out of its packing material and remove the lens caps on both sides.
2. Move the handle (A) of the lens anchor system to the right. (image 1-4)
4
R5976663 TLD HB (1.6-2.0:1) LENS KIT 22/12/2004
Page 9
1. TLD HB (1.6-2.0:1) Lens Kit
3. Push the lens, motors at the top, in the lens block gap horizontally, lining up the motor connector on the lens with the connector on the lens block (B), until the lens clicks in the lens anchor system.
Caution: For a table mounted projector, hold the pro jector when pushing the lens into the lens block to avoid sliding off from
Image 1-4 Lens installation
the table.
1.4 Quick Lens Adjustment
Quick zoom/focus adjustment
1. Press th e Selection key *, Barco key. Thezoom/focusmenuwillbedisplayed.(image1-5)
2. Push the cursor key or to zoom and or to focus the image.
3. When finished, press EXIT key to return or ENTER to continue to the shift adjustment.
LENS ADJUSTMENT ZOOM/FOCUS
ZOOM with or , FOCUS with or <ENTER> to shift <EXIT> to return
Image 1-5
Press the selection key * to switch to another pattern. Different patterns are available.
Quick shift adjustment
1. Press th e Selection key *, Barco key. The zoom/focus menu will be displayed (image 1-5).
2. Press ENTER. The shift menu will be displayed. (i
3. Push the cursor key or to shift the image up or down and or to shift the image left or right.
4. When finished, press EXIT key to return or ENTER to continue to zoom/focus.
mage 1-6)
R5976663 TLD HB (1.6-2.0:1) LENS KIT 22/12/2004
5
Page 10
1. TLD HB (1.6-2.0:1) Lens Kit
LENS ADJUSTMENT SHIFT
SHIFT with or , or <ENTER> to zoom/focus <EXIT> to return
Image 1-6
Press the selection key * to switch to another pattern. Different patterns are available.
1.5 Lens Formulas
Lens Formulas
PD
Projector
Screen
Image 1-7
To calculate the distance between the projector front side and the screen (PD) for a given screen width (SW), use the following formula:
SLM Projector Formula (in meter) Formula (in inches)
SLM G5 PD
SLM G8 PD
SLM G10 PD
SLM R6 PD
SLM R8 PD
SLM R10 PD
SW = Screen Height (Image Height) PD = Projector Distance, distance between screen and projector
= 1.62 x SW - 0.09
min
PD
= 2.03 x SW - 0.13
max
= 1.62 x SW - 0.09
min
= 2.03 x SW - 0.13
PD
max
= 1.62 x SW - 0.09
min
= 2.03 x SW - 0.13
PD
max
= 1.59 x SW - 0.09
min
= 2.00 x SW - 0.13
PD
max
= 1.59 x SW - 0.09
min
= 2.00 x SW - 0.13
PD
max
= 1.59 x SW - 0.09
min
= 2.00 x SW - 0.13
PD
max
PD
= 1.62 x SW - 3.54
min
PD
= 2.03 x SW - 5.12
max
PD
= 1.62 x SW - 3.54
min
= 2.03 x SW - 5.12
PD
max
PD
= 1.62 x SW - 3.54
min
= 2.03 x SW - 5.12
PD
max
PD
= 1.59 x SW - 3.54
min
= 2.00 x SW - 5.12
PD
max
PD
= 1.59 x SW - 3.54
min
= 2.00 x SW - 5.12
PD
max
PD
= 1.59 x SW - 3.54
min
= 2.00 x SW - 5.12
PD
max
SLM R12+ PD
= 1.47 x SW - 0.09
min
= 1.85 x SW - 0.13
PD
max
PD
= 1.47 x SW - 3.54
min
= 1.85 x SW - 5.12
PD
max
6 R5976663 TLD HB (1.6-2.0:1) LENS KIT 22/12/2004
Page 11
1. TLD HB (1.6-2.0:1) Lens Kit
RLM Projector
RLM G5 (*) PD
RLM G5+ (*) PD
RLM H5 (*) PD
RLM R6+
Formula (in meter) Formula (in inches)
= 2.01 x SW - 0.07
min
= 2.53 x SW - 0.11
PD
max
= 2.01 x SW - 0.07
min
= 2.53 x SW - 0.11
PD
max
= 1.61 x SW - 0.07
min
= 2.02 x SW - 0.11
PD
max
PD
= 1.47 x SW - 0.07
min
= 1.85 x SW - 0.11
PD
max
(*) Optical adapter R9832650 is required
1.6 Cleaning the lens
To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have de­veloped recommendations for cleaning the lens. FIRST, we recommend you try to remove any material from the lens by blowing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.
Necessary tools
TorayseeTMcloth (delivered together with the lens kit). Order number : R379058.
PD
= 2.01 x SW - 2.76
min
= 2.53 x SW - 4.33
PD
max
PD
= 2.01 x SW - 2.76
min
= 2.53 x SW - 4.33
PD
max
PD
= 1.61 x SW - 2.76
min
= 2.02 x SW - 4.33
PD
max
PD
= 1.47 x SW - 2.76
min
= 1.85 x SW - 4.33
PD
max
Howtocleanthelens?
Proceed as follow :
1. Always wipe lenses with a CLEAN Toraysee
2. Always wipe lenses in a single direction.
Warning: Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating.
3. Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.
4. If smears occur when cleaning lenses,
WARNING: Do not use fabric softener wh
cloth.
Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.
CAUTION: Other lenses can also be cleaned safely with this Toraysee
TM
cloth.
replace the cloth. Smears are the first indication of a dirty cloth.
en washing the cleaning cloth or softener sheets when drying the
TM
cloth.
R5976663 TLD HB (1.6-2.0:1) LENS KIT 22/12/2004 7
Page 12
1. TLD HB (1.6-2.0:1) Lens Kit
8 R5976663 TLD HB (1.6-2.0:1) LENS KIT 22/12/2004
Page 13
Revision Sheet
To:
Barco nv Events/Documentation
Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.89.70, Fax: +32 56.36.88.24 E-mail: antoon.dejaegher@barco.com, Web: www.barco.com
From: Date:
Please correct the following points in this documentation (R5976663/01):
page
wrong
correct
R5976663 TLD HB (1.6-2.0:1) LENS KIT 22/12/2004
Loading...