Barco PFWX-51B User Manual

PFWX-51B & PFWU-51B

8VHUPDQXDO

8VHUPDQXDO

Barco nv Projection Division

Noordlaan 5, B-8520 Kuurne

Phone: [phone]

Fax: [phone]

Support: www.barco.com/esupport

Visit us at the web: www.barco.com

Printed in China

Revision: 03

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the
implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to
the product(s) and/or the program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information
in this publication; these changes are incorporated in new editions of this publication.

The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the secured Barco
web site https://my.barco.com.

Copyright

All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded,
transmitted or stored in a retrieval system without the prior written consent of Barco.

©

EN55022/CISPR22 Class A ITE (Information Technology Equipment)

Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such equipment
should not be restricted in its sale but the following warning shall be included in the instructions for use:

Warning : This is a class A product. In a domestic environment this product may cause radio interference in which case the

user may be required to take adequate measures.

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible
for correcting any interference at his own expense.

Guarantee and Compensation

Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt,
the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and
manufacturing faults Barco must be informed immediately in writing of any complaints.

The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of
commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the
fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or
unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract. All other claims,
in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of
software as well as to other services provided by Barco, being a component of the system or independent service, will be
deemed invalid provided the damage is not proven to be attributed to the absence of properties guaranteed in writing or due
to the intent or gross negligence or part of Barco.

If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled
incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods
are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid.
Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry
provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee
provided by Barco either.

The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be
complied with by the customer.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their
respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be
understood as advertising for the products or their manufacturers.

TABLE OF CONTENTS

1. SAFETY 1

1.1 General considerations 1

1.2 Important safety instructions 2

2. GENERAL 5

2.1 Installation requirements 5

2.2 Unpacking the projector 6

2.3 Initial inspection 7

2.4 Projector configurations 8

2.5 Projector air inlets and outlets 10

2.6 Installation process overview 11

3. PHYSICAL INSTALLATION 12

3.1 Remote control unit (RCU) 12

3.2 Lenses 14

3.3 Connecting the projector with the power net 18

3.4 Alignment of a table mounted projector 19

3.5 Mounting the Ceiling mount 21

4. PROJECTOR PARTS AND FUNCTIONS 22

4.1 Projector front view 22

4.2 Projector Rear view 22

4.3 Input and Communication 23

4.4 Status lights of LED 26

4.5 Opening the I/O cover 27

4.6 Connecting the projector to other devices 28

5. GETTING STARTED 33

5.1 RCU & Local keypad 33

5.2 Remote Control and OSD Lite on Screen 33

5.3 Power on projector 34

5.4 Power off projector 35

5.5 Range of effective remote control signal reception 35

5.6 Source selection 35

TABLE OF CONTENTS

5.7 Changing OSD language 36

5.8 Adjusting the lens by horizontal and vertical lens shift 36

5.9 Introduction the OSD Lite on screen 37

6. ADVANCED OSD MENU 38

6.1 How to activate the Advanced OSD menu 38

6.2 How to navigate in the Advanced menu structure? 39

6.3 Advanced menu memory 39

7. IMAGE 40

7.1 Image menu overview 40

7.2 Display Mode 41

7.3 Brightness 41

7.4 Contrast 41

7.5 Computer 42

7.6 Auto Image 43

7.7 Advanced 44

7.8 Input Balance 45

8. SETTINGS 1 48

8.1 Settings 1 menu overview 48

8.2 Source 49

8.3 Projection 49

8.4 Aspect Ratio 50

8.5 Keystone 52

8.6 Digital Zoom 52

8.7 Advanced 1 52

8.8 Advanced 2 53

9. SETTINGS 2 54

9.1 Settings 2 menu overview 54

9.2 Auto Source 55

9.3 No Signal Power Off 56

9.4 Auto Power On 56

9.5 Lamp Mode 56

TABLE OF CONTENTS

9.6 Reset All 56

9.7 Status 56

9.8 Advanced 1 57

9.9 Advanced 2 59

10. MAINTENANCE 60

10.1 Lamp Replacement 60

10.2 Clean the dust 62

10.3 Cleaning the lens 62

10.4 Cleaning the exterior of the projector 62

10.5 Simple troubleshooting 63

11. PROJECTOR SPECIFICATION 65

11.1 PFWU-51B Specifications 65

11.2 PFWX-51B Specifications 67

11.3 Standard Source Files 69

11.4 Dimension 72

12. ENVIRONMENTAL INFORMATION 73

12.1 Disposal information 73

12.2 Rohs compliance 73

12.3 Production address 75

SAFETY

1.

About this chapter

Read this chapter attentively. It contains important information to prevent personal injury while installing and using a
PFWX-51B/PFWU-51B projector. Furthermore, it includes several cautions to prevent damage to the PFWX-51B/PFWU-51B
projector. Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this
chapter before installing your PFWX-51B/PFWU-51B projector. After this chapter, additional “warnings” and “cautions” are
given depending on the installation procedure. Read and follow these “warnings” and “cautions” as well.

1.1

General considerations

When referring in this document to the term “PRESENT SERIES” means that the content is applicable for following Barco
products:

PFWX-51B

•

PFWU-51B

•

WARNING: Ensure you understand and follow all the safety guidelines, safety instructions, warnings and

cautions mentioned in this manual.

1.Safety

WARNING: Be aware of suspended loads.

WARNING: Wear a hard hat to reduce the risk of personal injury.

WARNING: Be careful while working with heavy loads.

WARNING: Mind your fingers while working with heavy loads.

CAUTION: High pressure lamp may explode if improperly handled.

General safety instructions

Before operating this equipment please read this manual thoroughly and retain it for future reference.

•

Installation and preliminary adjustments should be performed by qualified Barco personnel or by authorized Barco service

•

dealers.
All warnings on the projector and in the documentation manuals should be adhered to.

•

All instructions for operating and use of this equipment must be followed precisely.

•

All local installation codes should be adhered to.

•

Notice on safety

This equipment is built in accordance with the requirements of the international safety standards IEC60950-1,
EN60950-1, UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology equipment
including electrical business equipment. These safety standards impose important requirements on the use of safety critical
components, materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard
and having access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation
levels, mechanical stability and strength, enclosure construction and protection against the risk of fire. Simulated single fault
condition testing ensures the safety of the equipment to the user even when the equipment’s normal operation fails.

PFWX-51B/PFWU-51B 10/02/2014

1

1.Safety

Users definition

Throughout this manual, the term SERVICE PERSONNEL refers to persons having appropriate technical training and experience
necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE
ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize
the potential risk to themselves or other persons. The term USER and OPERATOR refers to any person other than SERVICE PER­SONNEL, AUTHORIZED to operate professional projection systems.

A PFWX-51B/PFWU-51B projector is intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with
potential hazards associated with high voltage, high intensity light beams, ultraviolet exposure and high temperatures
generated by the lamp and associated circuits. Only qualified SERVICE PERSONNEL, knowledgeable of such risks, are allowed
to perform service functions inside the product enclosure.

1.2

Important safety instructions

To prevent the risk of electrical shock

This product should be operated from a mono phase AC power source.

•

This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power

•

cables are the correct one, consult your dealer. If you are unable to insert the plug into the outlet, contact your electrician
to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To

•

disconnect the cord, pull it out by the plug. Never pull the cord itself.
Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety

•

tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer.
Do not operate the projector with a damaged cord. Replace the cord.Do not operate the projector if the projector has been

•

dropped or damaged until it has been examined and approved for operation by a qualified service technician.
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.

•

If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord

•

rated for less amperage than the projector may overheat.
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short

•

out parts that could result in a risk of fire or electrical shock.
Do not expose this projector to rain or moisture.

•

Do not immerse or expose this projector in water or other liquids.

•

Do not spill liquid of any kind on this projector.

•

Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel

•

before resuming operations.
Do not disassemble this projector, always take it to an authorized trained service person when service or repair work is

•

required.
Do not use an accessory attachment which is not recommended by the manufacturer.

•

Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused

•

for long periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC
power-line surges.

To prevent personal injury

Isolate electrically before replacing the lamp or lamp house. Caution: Hot lamp (house).

•

Caution: High pressure lamp may explode if improperly handled. Refer servicing to qualified service personnel.

•

To prevent injury and physical damage, always read this manual and all labels on the system before inserting the lamp

•

casing, connecting to the wall outlet or adjusting the projector.
To prevent injury, take note of the weight of the projector. Minimum 2 persons are needed to carry the projector.

•

To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.

•

Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.

•

Warning: extremely high brightness lamps: This projector uses extremely high brightness lamps. Never attempt to

•

look directly into the lens or at the lamp. If the projection distance is less than 6 meter, any person needs to be at least 4
meters away from the projected image. Avoid close range reflection of the projected image on any reflecting surface (such
as glass, metal, …) . When operating the projector, we strongly recommend wearing suitable safety glasses.
Before attempting to remove any of the projector’s covers, you must turn off the projector and disconnect from the wall

•

outlet.
When required to switch off the projector, to access parts inside, always disconnect the power cord from the power net.

•

The power input at the projector side is considered as the disconnect device. When required to switch off the projector, to

•

access parts inside, always disconnect the power cord at the projector side. In case the power input at the projector side is
not accessible (e.g. ceiling mount), the socket outlet supplying the projector shall be installed nearby the projector and be
easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring.
Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and

•

possible injury to the user.

2

PFWX-51B/PFWU-51B 10/02/2014

It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if they have

•

become visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches.
Warning: Protection from ultraviolet radiation: Do not look directly in the light beam. The lamp contained in this

•

product is an intense source of light and heat. One component of the light emitted from this lamp is ultraviolet light.
Potential eye and
skin hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unnecessary exposure. Protect
yourself and your employees by making them aware of the hazards and how to protect themselves. Protecting the skin
can be accomplished by wearing tightly woven garments and gloves. Protecting the eyes from UV can be accomplished by
wearing safety glasses that are designed to provide UV protection. In addition to the UV, the visible light from the lamp is
intense and should also be considered when choosing protective eye wear.
Exposure to UV radiation: Some medications are known to make individuals extra sensitive to UV radiation. The American

•

Conference of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure for an-8 hour day to be
less than 0,1 micro-watts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to
assure employees are not exposed to cumulative radiation levels exceeding these government guidelines. The exposer of
this UV radiation is allowed for only 1 hour per day for maintenance and service persons.
Mercury Vapor Warnings: Keep the following warnings in mind when using the projector. The lamp used in the projector

•

contains mercury. In case of a lamp rupture, explosion there will be a mercury vapor emission. In order to minimize the
potential risk of inhaling mercury vapors:

- Ensure the projector is installed only in ventilated rooms.

- Replace the lamp module before the end of its operational life.

- Promptly ventilate the room after a lamp rupture, explosion has occurred, evacuate the room (particularly in case of a
pregnant woman).

- Seek medical attention if unusual health conditions occur after a lamp rupture, explosion, such as headache, fatigue,
shortness of breath, chest-tightening coughing or nausea.

1.Safety

To prevent fire hazard

Do not place flammable or combustible materials near the projector!

•

Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations.

•

This projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both
normal and safe. Exposing flammable or combustible materials into close proximity of this projector could result in the
spontaneous ignition of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an “exclusion
zone” around all external surfaces of the projector whereby no flammable or combustible materials are present. The
exclusion zone must be not less than 50 cm (20”) for all DLP projectors. The exclusion zone on the lens side must be at
least 5 m. Do not cover the projector or the lens with any material while the projector is in operation. Keep flammable
and combustible materials away from the projector at all times. Mount the projector in a well ventilated area away from
sources of ignition and out of direct sun light. Never expose the projector to rain or moisture. In the event of fire, use
sand, CO2 or dry powder fire extinguishers. Never use water on an electrical fire. Always have service performed on this
projector by authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco
replacement parts as they may degrade the safety of this projector.
Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to

•

protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by
placing the projector too close to walls, or other similar surface. This projector should never be placed near or over a
radiator or heat register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation
is provided.
Projection rooms must be well ventilated or cooled in order to avoid build up of heat.

•

Let the projector cool down completely before storing. Remove cord from the projector when storing.

•

Heat sensitive materials should not be placed in the path of the exhausted air or on the lamp house.

•

To prevent projector damage

This projector has been designed for use with a specific lamp (house) type. See installation instructions for its correct type.

•

The air filters of the projector must be cleaned or replaced on regular base (a "clean" booth would be monthly-minimum).

•

Neglecting this could result in disrupting the air flow inside the projector, causing overheating. Overheating may lead to
the projector shutting down during operation.
The projector must always be installed in a manner which ensures free flow of air into its air inlets and unimpeded

•

evacuation of the hot air from its cooling system.
In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic Compatibility

•

(EMC)requirements, it should always be operated with all of it’s covers in place.
Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it

•

from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat
register. The device should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the mains

•

supply immediately. Do not operate the projector again until it has been checked by qualified service personnel.
Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects may not

•

be nearer to the projector than 30 cm (12") on any side.

PFWX-51B/PFWU-51B 10/02/2014

3

1.Safety

Do not use this equipment near water.

•

Special care for Laser Beams:Special care should be used when DLP projectors are used in the same room as high power

•

laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices™
in which case there is a loss of warranty.
Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror Devices TM in

•

which case there is a loss of warranty.
Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment.

•

For maximum protection, repack your set as it was originally packed at the factory.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth

•

for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the
cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution.
To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective

•

coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth,
detergent solution, or thinner.
Rated maximum ambient temperature, ta= 40 °C (104 °F).

•

The lamp house shall be replaced if it has become damaged or thermally deformed.

•

On servicing

Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage

•

potentials and risk of electric shock.
Refer all servicing to qualified service personnel.

•

Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual

•

can lead to permanent damage to the projector and cancellation of the warranty.
Unplug this product from the wall outlet and refer servicing to qualified service technicians under the following conditions:

•

- When the power cord or plug is damaged or frayed.

- If liquid has been spilled into the equipment.

- If the product has been exposed to rain or water.

- If the product does not operate normally when the operating instructions are followed. Adjust only those controls that
are covered by the operating instructions since improper adjustment of the other controls may result in damage and will
often require extensive work by a qualified technician to restore the product to normal operation.

- If the product has been dropped or the cabinet has been damaged.

- If the product exhibits a distinct change in performance, indicating a need for service.
Replacement parts: When replacement parts are required, be sure the service technician has used original Barco

•

replacement parts or authorized replacement parts which have the same characteristics as the Barco original part.
Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards.
Unauthorized substitutions may void warranty.
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety

•

checks to determine that the product is in proper operating condition.
Possible explosion hazard: Always keep in mind the caution below:

•

CAUTION: Do not touch a lamp during operation and right after it is turned off as it is extremely hot. Lamp

contains mercury. It's brokeage might cause mercury or broken glass pieces to folow out of lamp housing.
To avoid exposure the risk of mercury poisoning. Don't drop, hit, force or scratch while handing a lamp.

To prevent battery explosion

Danger of explosion if battery is incorrectly installed.

•

Replace only with the same or equivalent type recommended by the manufacturer.

•

For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and

•

regulations to ensure proper disposal.

4

PFWX-51B/PFWU-51B 10/02/2014

GENERAL

2.

About this chapter

Read this chapter before installing your PFWX-51B/PFWU-51B projector. It contains important information concerning
installation requirements for the PFWX-51B/PFWU-51B projector, such as minimum and maximum allowed ambient
temperature, humidity conditions, required safety area around the installed projector, required power net, etc.

Furthermore, careful consideration of things such as image size, ambient light level, projector placement and type of screen
to use are critical to the optimum use of the projection system.

Overview

Installation requirements

•

Unpacking the projector

•

Initial inspection

•

Projector configurations

•

Projector air inlets and outlets

•

Installation process overview

•

WARNING: Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated

terms of guarantee. Observing the specification mentioned in this chapter is critical for projector
performance. Neglecting this can result in loss of warranty.

2.General

2.1

Installation requirements

Environment conditions

Table below summarizes the physical environment in which the PFWX-51B/PFWU-51B projector may be safely operated or
stored.

Environment Operating Non-Operating
Ambient Temperature

Humidity

Altitude

Let the projector acclimatize after unpacking. Neglecting this may result in a startup failure of the Light
Pro- cessor Unit.

5°C (41°F) to 35°C (95°F)

10% to 85% RH Non-condensed

-60 (-197Ft) to 3000m (9843Ft)

-10°C (14°F) to 60°C (140°F)

5% to 90% RH Non-Condensed

-60 (-197Ft) to 10000m (32810Ft)

Cooling requirements

The projector is fan cooled and must be installed with sufficient space around the projector head, minimum 30 cm (12 inch) to
ensure sufficient air flow. It should be used in an area where the ambient temperature, as measured at the projector air inlet
, does not exceed +35°C (+95°F).

Clean air environment

A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors ventilation
inlets. For installations in environments where the projector is subject to airborne contaminants such as that produced by
smoke machines or similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging
electronic surfaces, degrading performance), then it is highly advisable and desirable to have this contamination removed
prior to it reaching the projectors clean air supply. Devices or structures to extract or shield contaminated air well away
from the projector are a prerequisite, if this is not a feasible solution then measures to relocate the projector to a clean air
environment should be considered.

Only ever use the manufacturer’s recommended cleaning kit which has been specifically designed for cleaning optical parts,
never use industrial strength cleaners on the projector’s optics as these will degrade optical coatings and damage sensitive
optoelectronics components. Failure to take suitable precautions to protect the projector from the effects of persistent and
prolonged air contam- inants will culminate in extensive and irreversible ingrained optical damage. At this stage cleaning of

PFWX-51B/PFWU-51B 10/02/2014

5

2.General

the internal optical units will be noneffective and impracticable. Damage of this nature is under no circumstances covered
under the manufacturer’s warranty and may deem the warranty null and void. In such a case the client shall be held solely
responsible for all costs incurred during any repair. It is the clients responsibility to ensure at all times that the projector
is protected from the harmful effects of hostile airborne particles in the environment of the projector. The manufacturer
reserves the right to refuse repair if a projector has been subject to knowingly neglect, abandon or improper use.

Main Power requirements

The PFWX-51B/PFWU-51B projector operates from a nominal mono phase power net with a separate earth ground PE.

Projector Power requirements

PFWX-51B AC INPUT 100-240V 4.8A 50/60Hz

PFWU-51B AC INPUT 100-240V 4.8A 50/60Hz

The power cord required to connect the projector with the power net is delivered with the projector.

Projector weight

Do not underestimate the weight of the PFWX-51B/PFWU-51B projector. The projector weights about ±12 kg (±26.5 lb.)
without lens. Be sure that the pedestal or ceiling mount on which the projector has to be installed is capable of handling five (5)
times the complete load of the system.

2.2

Unpacking the projector

1. Remove the tape around the carton box, then open the box.

2. Take out the foam upper the projector.

3. Take out the projector.

6

PFWX-51B/PFWU-51B 10/02/2014

2.General

After unpacking let the projector acclimatizes to a room temperature higher then 5°C (41°F) and lower then
35°C (95°F). Neglecting this may result in a start up failure of the Light Processor Unit.

Save the original shipping carton and packing material, they will be necessary if you ever have to ship your
projector. For maximum protection, repack your projector as it was originally packed at the factory.

2.3

Initial inspection

General

Before shipment, the projector was inspected and found to be free of mechanical and electrical defects. As soon as the
projector is unpacked, inspect for any damage that may have occurred in transit. Save all packing material until the inspection
is completed. If damage is found, file claim with carrier immediately. The Barco Sales and Service office should be notified as
soon as possible.

Box content

After unpacking the projector it is recommended to check if all following items where included:

Projector with standard lens mounted.

•

Three power cords

•

CD (Contents has this installation manual)

•

One Safety manual

•

One remote control unit (RCU)

•

Two AAA size batteries for the RCU. Type: size-AAA (R03). Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries

•

should be used.

Lamp is mounted inside the lamp house at delivery.

Mechanical check

This check should confirm that there are no broken knobs or connectors, that the cabinet and panel surfaces are free of dents
and scratches, and that the operating panel is not scratched or cracked. The Barco Sales and Service office should be notified
as soon as possible if this is not the case.

PFWX-51B/PFWU-51B 10/02/2014

7

2.General

F/C

AUDIENCE

F/T

FLOOR

SCREEN

Frontprojection

2.4

Projector configurations

The different configurations

Depending on the installation the projector can be mounted in different ways, the different configurations are:

1. Front / Table (F/T)

2. Front / Ceiling (F/C) (upside down)

3. Rear / Table (R/T)

4. Rear / Ceiling (R/C) (upside down)

Front projection

The projector is installed, either in a table mount or ceiling mount configuration, at the same side of the screen as the
audience.

8

PFWX-51B/PFWU-51B 10/02/2014

Rear projection

Re

The projector is installed, either in a table mount or ceiling mount configuration, at the other side of the screen opposite the
audience.

AUDIENCE BACKSTAGE

R/C

2.General

ar projection

Positioning the projector

ACD

PD

FLOOR

FLOOR

SCREEN

SCREENSCREEN

SHB

R/T

SW

SHB

SCREEN

CD

The projector should be installed at right angles (horizontally and vertically) to the screen at a distance PD. Note the distance
(A) between lens centre and table surface is slightly variable. This distance (A) is nominal 8.3 cm in case all feet are turned in
completely and the vertical lens shift is set to zero (0).

On axis / off axis projection

The position of the projector with reference to the screen may also be different depending on the installation. Basically the
projector can be positioned in On-Axis or Off-Axis configuration. On-Axis configuration means that the projector is positioned
so as to have the centre of the lens coinciding with the centre of the screen. Off-Axis projection is obtained by shifting the
lens up, down, left or right. Several parameters can be calculated determining the position in any installation.

Formula to calculate the distance CD for On-Axis projection: CD = SH/2 + B - A

Shift range

The lens can be shifted with respect to the DMD (P) which result in a shifted image on the screen (Off-Axis). A 100% shift
means that the centre point of the projected image is shifted by half the screen size. In other words, the centre point of

PFWX-51B/PFWU-51B 10/02/2014

SW

Positioningprojector

9

2.General

the projected image falls together with the outline of the image in an On-Axis projection. Due to mechanical and optical
limitations it’s recommended to keep the shift values within the field of view (F) as illustrated below. Within these shift
ranges the projector and lens perform excellently. Configuring the projector outside these shift ranges will result in a slight
decline of image quality.

+110%

U

-10 % +10%

L R

D

-30%

Vertical andhorizontalshift range

PDMD.
FField of view.

It is mechanical possible to shift outside the recommended field of view, but it will result in a decline of
image quality depending on the used lens and the zoom position of the used lens. Furthermore, shifting
too much in both directions will result in a blurred image corner.

F

P

F

P

P

F

U

D

L

R

SIDE VIEW

TOP VIEW

Horizontal and vertical projector tilt ranges

Avoid to reduce the usage of lamp life. Suggest the projector rotated and mounted vertical angle not > ±15°.

+110%

-30%

-10%

+10%

Side to side tilt, however, must not exceed ±10°. This limit ensures that the lamp in the projector operates properly and safely.

B

MAX

10°

10°

A

A

MAX

10°

10°

MAX

±15° ±15°

MAX

A

C

A Tilting allowed without problems
B No tilting allowed in th is are a
C No tilting allowed in th is are a

2.5

Projector air inlets and outlets

Ventilation inlet:

The internal cooling fan draws cool air from the ventilation inlet into the projector.

10

Ventilation outlet:

The hot air generated inside the projector is dispersed through the ventilation slot. Make sure the ventilation slot is free from

PFWX-51B/PFWU-51B 10/02/2014

obstruction.

Ventilation outlet

2.6

Installation process overview

2.General

Ventilation inlet

Quick setup

The following steps describe briefly how to setup your PFWX-51B/PFWU-51B projector in a table mount front projection. Note
that each step refers to a corresponding procedure, which is more detailed and illustrated.

Install the batteries of the remote control. See page 12: Remote control unit (RCU).

1.
Place the projector on a solid table in front of the screen at the expected throw distance. Adjust the feet to ensure that

2.
the projector is installed at right angles (horizontally and vertically) with the screen. See page 19: Alignment of a table

mounted projector and page 36: Adjusting the lens by horizontal and vertical lens shift.

Connect the projector with the local power net. See page 18: Connecting the projector with the power net.

3.
Select and install an appropriate lens, which covers the throw ratio ( = screen size / projector screen distance).

4.
See page 9: Positioning the projector.

Switch ON the projector. See page 18: Connecting the projector with the power net.

5.
Connect your source to the appropriate input module. See page 23: Input and Communication.

6.
Zoom and shift the lens until the image is properly projected on the screen, Do this by using the “ZOOM” and “FOCUS”

7.
ring on the lens. If necessary, level the projector from side to side by turning the adjustable feet in or out. See page 16:

Lens zoom. or adjust the Lens Shift manually. See page 36: Adjusting the lens by horizontal and vertical lens shift

PFWX-51B/PFWU-51B 10/02/2014

11

3.Physical Installation

PHYSICAL INSTALLATION

3.

About this projector

This chapter describes how the mechanical set up of the projector has to be done and how to realize the electrical
connections.

Overview

Remote control unit (RCU)

•

Lenses

•

Connecting the projector with the power net

•

Alignment of a table mounted projector

•

Mounting the ceiling mount

•

3.1

Remote control unit (RCU)

Introduction

Remove the cover by sliding it in the
direction indicated by the arrow.

´

Insert two new AAA
batteries (observe the polarity).

Replace the cover.

´

Notes for the Remote control unit

Be sure to insert the batteries in the corresponding orientations to match the polarities.

•

Do not mix new batteries with used batteries as it would shorten the life of new batteries or cause leakage.

•

Only used AAA batteries as instructed; do not attempt to insert different types of batteries into the remote control.

•

If the remote is going to be unused for long periods of time, be sure to remove the batteries to prevent leakage, which

•

could damage the remote control.
The liquid contents in the batteries is harmful to the skin; do not touch the leakage with your bare hands directly. When

•

installing fresh batteries, be sure to clean up the leakage thoroughly.
Under most circumstances, you only need to point the remote control towards the screen and the IR signal would be

•

reflected off the screen and picked up by the IR sensor on the projector.But under specific circumstances, the projector may
fail to receive signals from the remote control due to environmental factors.When this happens, orient the remote control
at the projector and try again.
If the range of effective remote control signal reception decreases or if the remote control stops working, replace the

•

batteries.
If the infrared receiver is exposed to fluorescent lamp or strong sunlight, the remote control may not operate normally.

•

Refer to the regulations enforced by your local government on the disposal of used batteries; improper disposal could

•

damage the environment.

12

PFWX-51B/PFWU-51B 10/02/2014

Remote Control overview

3.Physical Installation

ON/OFF

HOME

OK

ARROW RIGHT

ARROW UP

ARROW LEFT

ARROW DOWN

LED INDICATION

BATTERY COMPARTMENT

IR LED'S

Basic Remote Command result RCU Lite action

start the projector press "ON/OFF"

turn off the projector press "ON/OFF"

show main menu on screen press "HOME"

move through menu press "arrow keys"

select button press "OK"

select and return to previous menu press "OK"

return to previous menu without
selecting

clear OSD Lite of screen press "HOME"

PFWX-51B/PFWU-51B 10/02/2014

>

press "HOME"

13

3.Physical Installation

3.2

Lenses

Available lenses for the PFWX-51B/PFWU-51B projector

PWFX-51B

Lens standard Lens short throw Lens long throw
R9832757 R9832758 R9832759
F lens (1.62-2.03:1) F lens (0.81:1) F lens (2.03-3.05:1)

PWFU-51B

Lens standard Lens short throw Lens long throw
R9832757 R9832758 R9832759
F lens (1.54-1.93:1) F lens (0.77:1) F lens (1.93-2.89:1)

Projection lenses are optional accessories. Please contact your local dealer to acquire the projection lens
that suits your need most.

Removing the Existing Lens From the Projector

Push down and release the lens shift cover to open.

1.
Push the LENS RELEASE button to the unlock position.

2.

Grasp the lens.

3.
Rotate the lens counterclockwise. The lens disengages.

4.

14

Carefully pull out the lens.

5.

PFWX-51B/PFWU-51B 10/02/2014

Installing a New Lens

Remove both end caps from the lens.

Align the notches and correctly position the electrical contact pad as shown in the picture.

1.

3.Physical Installation

Electrical
contact
pins

Rotate the lens clockwise until it clicks in place.

2.

Electrical contact pins should be in the direction as shown in the picture.

PFWX-51B/PFWU-51B 10/02/2014

15

3.Physical Installation

Lens focus

Sharpen the picture by rotating the focus ring.

Lens zoom

Adjust the projected picture to the size that you need using the zoom ring.

—>

Original image size

Zoom out Zoom in

16

PFWX-51B/PFWU-51B 10/02/2014

3.Physical Installation

Range of vertical
lens shift adjustment

Range of vertical

Range of

Lens Shift

In addition to using the adjustable feet to adjust projection angle, you can also use the Lens Shift function to adjust the
projected image.

Moving the lens vertically

•

The distance of vertical lens movement is +110% , -30% of half the screen height in both directions.For instance, if you are
using a 80" × 50" screen, you will be able to move the image upwards no more than 27.5'' or downwards no more than 7.5''.

lens shift
adjustment

This illustration shows normal vertical
lens shift without the use of special
specification lens or projector.

Moving the lens horizontally

•

The distance of horizontal lens movement is 10% of half the screen width in both directions. For instance, if you are using
a 80" × 50" screen, you will be able to move the image left or right by no more than 4".

Please make sure the center of lens is retangular to the center of the screen.

horizontal
lens shift

adjustment

Range of

horizontal
lens shift
adjustment

This illustration shows normal horizontal lens shift without the use of special specification lens or projector.

PFWX-51B/PFWU-51B 10/02/2014

17

3.Physical Installation

3.3

Connecting the projector with the power net

Connect the female side of the power cord with the power input socket of the projector (1).

1.
Secure the power plug by locking the plug holder clamp (2).

2.

Connect to Wall plug

CAUTION: Use only the power cord provided with the projector.



Connect the male side of the power cord to the local power net.

3.

This power cord for Europe
and Korea

This power cord for USA This power cord for China



18

PFWX-51B/PFWU-51B 10/02/2014

3.Physical Installation

CAUTION: Ensure that the power net meets the power requirements of the projector.

WARNING: Do not attempt operation if the AC supply and cord are not within the specified voltage and

power range.

CAUTION: Once the projector is switched to standby, the lamp cooling fans will continue to run for approx-

imately five minutes to ensure that the projector and lamp have sufficiently cooled, at which point the fans
will automatically decrease to standby. To avoid thermal stress that can lead to premature lamp failure,
never unplug the power cord while the lamp cooling fans are running. Never unplug the power cord to
power down the projector, first switch off the power switch and then unplug the power cord.

3.4

Alignment of a table mounted projector

How to align the projector

Place the projector in the desired location. Take into account the zoom range of the used lens and the size of the screen.

1.
Project one of the internal grid patterns on the screen.

2.
Turn the adjustable feet in or out until the projected grid pattern has a perfect rectangle shape and is leveled.

3.

PFWX-51B/PFWU-51B 10/02/2014

19