Barco Orion 1080, Orion Cinemascope Safety And Users Manual

ORION

User & Safety Manual

2

3

1 Contents of this User Manual

1 Introduction 7

1.1 Overview

1.2 Training

1.3 Symbols used in this documentation

2 Safety and compliance 9

2.1 General safety considerations

2.2 Information/Warning - Potential Mercury Vapor Health Issues

2.3 FCC compliance

2.4 Disposal information

2.4.1 Statement WEEE (Waste Electrical and Electronic Equipment)

2.4.2 Disposal of batteries in the product

2.4.3 Turkey RoHS compliance

2.5 Service

2.6 Light beam Hazard Distance (HD)

2.6.1 Restriction zone based on the HD

2.7 HD in function of the lens Throw Ratio

2.7.1 Hazard Distance

3 What is in the box? 15

4 Installation 17

4.1 System considerations

4.2 Ventilation

4.2.1 Ventilation accessories

4.3 Ceiling and rig mounting

4.4 Locking the projector

4.5 Projector angle (tilt)

4.6 Selecting a lens

4.6.1 Inserting a lens

4.6.2 Changing/removing a lens

4.6.3 Lens range

4.7 Lens lock

4.8 Lens shift

4.9 Lens planarity (Scheimpflug adjustment)

4.10 Zoom, focus and iris

4.11 Making the connections

4.12 Connecting video and data sources

4

4.13 Connecting control interfaces

4.14 Source format integrity – EDID

4.15 Image sizes

5 Overview 27

5.1 Keypad and indicator

5.2 Wireless remote control

5.3 Connectors

5.3.1 Signal connectors

5.3.2 Control connectors

5.4 Menu system

5.4.1 Top menu

5.5 3D main menu

5.5.1 3D > Dual head setup sub menu

5.6 Picture main menu

5.6.1 Picture > RealColor sub menu

5.6.2 Picture > Advanced sub menu

5.7 Installation main menu

5.7.1 Installation > EDID sub menu

5.7.2 Installation > Synchronization sub menu

5.8 Settings main menu

5.8.1 Settings > Pin Code sub menu

5.8.2 Settings > Network sub menu

5.8.3 Settings > Factory Reset sub menu

5.8.4 Settings > Service sub menu

5.9 Languages main menu

5.10 Status main menu

5.10.1 Status > Source Information sub menu

5.10.2 Status > Source Information > Advanced sub menu

5.10.3 Status > Source Synchronisation sub menu

6 Functionality 51

6.1 Powering On and Off

6.1.1 Manual power control

6.1.2 DPMS - power down

6.1.3 Standby ECO mode

6.2 Image alignment

6.2.1 Image orientation

6.3 Language

6.4 System status

6.5 Lamp power

6.6 Source selection, source scan

6.7 On screen display (OSD) messages

6.7.1 Disabling the STATUS indicator

5

6.7.2 Setting the background color

6.7.3 Setting OSD menu timeout

6.7.4 Selecting the startup logo

6.8 Picture by Picture (PbP)

6.9 PIN code

6.10 Disabling the wireless remote control (IR) receivers

6.11 Software upgrades

7 Optimizing the image 57

7.1 Calibration data

7.1.1 Updating RealColor™ calibration data

7.1.2 RealColor™ modes

7.2 Setting a white point or color temperature

7.2.1 Defining the system color gamut

7.3 Gamma

8 Technical specifications 65

9 Lamp change 67

6

7

1 Introduction

1.1 Overview

Welcome to the world of Barco’s high performance projectors.

The Orion series feature high performance optics and lenses, excellent resolution, updated signal
processing and built-in frame-lock synchronization, making it the ideal projector for multi-channel
visualization and simulation applications.

This manual is applicable for the following Barco projectors:

•

Orion 1080 (1920x1080)

• Orion Cinemascope (2560x1080)

1.2 Training

Training is available at the Barco University, with course levels ranging from basic projector use to
advanced set-up and configuration across multiple applications.

Go to www.barco.com for more information.

1.3 Symbols used in this documentation

WARNING: Potential danger to people or equipment when using the product in certain

ways.

NOTE: Essential handling requirements for the projector. If not followed, they may cause
product malfunction.

TIP: Manufacturer recommendations related to projector usage and performance.

The specifications and functionality of this projector may change without prior notice.

Pictures/drawings or features in this user guide may be different from your

projector depending on model/version.

8

9

2 Safety and compliance

2.1 General safety considerations

• Use only the cables and cords supplied with the projector or original replacement cables. Using other cables
or cords may lead to malfunction and permanent damage to the unit.

• Always use 3-prong (grounded) power cord to ensure proper grounding of the unit. Never use 2-prong power
cords, as this is dangerous and could lead to electrical shock.

• Never open the unit. The projector contains no user serviceable parts. Refer all repairs to qualified personnel
only. Make sure that no objects enter into the vents and openings of the set.

• Do not spill any liquids on the projector or into the vents or openings of the unit.

• Always remove lens cap before switching on the projector. If the lens cap is not removed, it may melt due to

the high energy light emitted through the lens. Melting the lens cap may permanently damage the surface
of the projection lens.

• Do not look into the projection lens when the projector is switched on. The strong light may permanently
damage sight.

• Only place the projector on a stable surface, or mount it securely using an approved ceiling-mount.

• Do not drop the projector.

• Always operate the projector according to the rotation guidelines. Operating the unit in other positions may

reduce lamp life significantly, and may lead to overheating, resulting in malfunctioning.

• Always allow ample airflow through the projector. Never block any of the air vents. Never cover the unit in
any way while running. Allow for sufficient distance to walls and ceilings to avoid overheating.

• Minimum safety distance to any side of the unit is 50 cm / 20” in any direction (15 cm/ 6” to ceiling).

• Hot air is exhausted from the rear vent. Do not place objects that are sensitive to heat nearer than 50 cm /

20” to the exhaust vent.

• The projector is designed for indoor use only. Never operate the unit outdoors.

• Do not operate the projector outside its temperature and humidity specifications, as this may result in over-

heating and malfunctioning.

• Only connect the projector to signal sources and voltages as described in the technical specification. Connect­ing to unspecified signal sources or voltages may lead to malfunction and permanent damage of the unit.

• In order to prevent damage to the projector caused by over-voltages (e.g. lightning), we recommend connec­tion to a line (mains) circuit which has over voltage protection.

• Allow lamp to cool down for at least 60 minutes before changing.
USE ONLY ORIGINAL LAMPS.

• Connecting sources to a powered projector may result in product failure. It is recommended that the power
cable connector (projector-end) or the mains power socket is accessible whilst the product is in use to
enable mains power to be disconnected or switched off when connecting source devices. This should be
considered during product installation.

10

2.2 Information/Warning - Potential Mercury Vapor Health Issues

This projector uses a very powerful UHP™ lamp to produce an extremely bright image.

This technology is similar to other high-pressure discharge lamps that are extensively used in cars, street lights
and other lighting appliances today. These lamps, like fluorescent lighting, contain small amounts of mercury. The
amount of mercury present in a lamp is far below the limits of danger set by the authorities. It is however very
important that lamps containing mercury are treated properly to minimize potential health hazards.

The UHP™ lamp, like any other high brightness projector lamp, is operating under high-pressure. Even if the lamp
and the projector are carefully designed to minimize the probability of lamp rupture, the lamp may break while
operating and small amounts of mercury vapor may be emitted from the projector. The probability of rupture
increases when the lamp reaches its expected lifetime. It is therefore highly recommended that the lamp is
replaced when the specified lifetime is reached.

As a general precaution, secure good ventilation in the room when operating the projector. If lamp rupture occurs,
evacuate the room and secure good ventilation. Children and pregnant women in particular should leave the
room.

When replacing a worn lamp, dispose of the used lamp carefully by proper recycling.

Mercury is a naturally occurring, stable metallic element that may pose a safety risk to people under certain
conditions. According to the Public Health Statement for Mercury published by the Agency for Toxic Substances
and Disease Registry (“ATSDR”, part of the United States Public Health Service), the brain, central nervous system
and kidneys are sensitive to the effects of mercury, and permanent damage can occur at sufficiently high levels of
exposure. Acute exposure to high concentrations of mercury vapor can cause conditions such as lung and airway
irritation, tightness in the chest, a burning sensation in the lungs, coughing, nausea, vomiting and diarrhea. Chil­dren and fetuses are particularly sensitive to the harmful effects of metallic mercury to the nervous system.

Seek medical attention if any of the above symptoms are experienced or if other unusual conditions are experi­enced following lamp rupture.

This product contains chemicals, including lead, known to the State of California to cause birth defects or
other reproductive harm. Recycle properly; do not dispose of in ordinary waste!

2.3 FCC compliance

FCC regulations state that changes or modifications not expressly approved by the party responsible manufacturer
could void your authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc­tion manual, may cause harmful interference to radio communications.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

If operation of this equipment does cause interference with radio communications services, which can be deter­mined by turning the equipment off and on, you are encouraged to contact the installer used, or consult a Barco
Support representative who will try to correct the interference by one or more of the following measures:

• Reorient the receiving antenna.

• Relocate the Barco product with respect to the receiver.

• Move the Barco product away from the receiver.

• Other

CANADA
This Class A digital apparatus complies with Canadian ICES-003. / Cet appareil numérique de la classe A est con-

forme à la norme NMB- 003 du Canada.

11

2.4 Disposal information

2.4.1 Statement WEEE (Waste Electrical and Electronic Equipment)

This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electri­cal and electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of
your waste equipment by handing it over to a designated collection point for the waste recycling of electrical and
electronic equipment. To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate these items from other types of waste and recycle them responsibly to promote the
sustainable reuse of material resources.

For more information about recycling of this product, please contact your local city office or your municipal waste
disposal service. For details, please visit the Barco website at:
http://www.barco.com/en/AboutBarco/weee.

2.4.2 Disposal of batteries in the product

This product contains batteries covered by the European Directive which must be collected and disposed of sepa­rately from municipal waste.

If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical
symbols will appear below the crossed-out wheeled bin symbol.

By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent poten­tial negative effects on the environment and human health.

2.4.3 Turkey RoHS compliance

Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur.
(Republic of Turkey: In conformity with the WEEE Regulation)

2.5 Service

This product contains no user serviceable parts. If the product fails to function as expected, please first check that
all connections are properly made, and that the power cord is properly connected. Please check that the projector
as well as the video and computer sources is switched on. Cables and cords may break over time. Try to change
cables and cords, in case there is a bad or intermittent connection. Check if the circuit breaker or mains fuse is
intact. In the event of product failure, please contact your reseller. You should prepare a description of the symp­toms of failure you experience. Please also state product number and serial number as printed on the label on the
bottom or side of the projector.

Service personnel must use UV radiation eye- and skin protection during servicing

Pb

12

2.6 Light beam Hazard Distance (HD)

Light beam Hazard Distance (HD) is the distance from the source at which the intensity or the energy per
surface unit becomes lower than the applicable safety limit. The light beam can be considered dangerous
if the operator is within the HD.

2.6.1 Restriction zone based on the HD

Calculation of the HD depends on the amount of lumens produced by the projector and the type of lens installed.
See next section, HD in function of the lens Throw Ratio (TR).

To protect untrained users, the following installation requirements must be complied with: light output levels in
excess of the limits shall not be permitted at any point less than 2.0 meters (SH) above any surface upon which
persons are assumed to stand or 1 meter (SW ) below or in lateral separation from any place where such persons
are assumed to be.

Based on national requirements, no person is allowed to enter the projected beam within the zone between the
projection lens and the related hazard distance (HD). This shall be made physically impossible by creating suffi­cient separation height or by placing barriers. The minimum separation height takes into account the surface upon
which persons are assumed to stand. A typical setup is shown in the image below. A professional installed must
verify that the minimum requirements are met.

RA

TH

PR

RZ

HD

SW

1m

SW

SW

SW

HD

SH

RA TH

RZ

SH

(B) TOP VIEW(A) SIDE VIEW

A Side view.

B Top view.

RA Restricted Access location (boot area of projector).

PR Projector.

TH Theater.

RZ Restriction Zone in the theater.

SH Separation Height. Must be minimum 2 meter.

SW Separation Width. Must be minimum 1 meter

If required a restricted zone (RZ) in the theater must be established. This can be done using a physical barrier, for
example, a red rope as shown in the image on the next page.

13

PR

2.7 HD in function of the lens Throw Ratio

2.7.1 Hazard Distance

Throw Ratio (TR) is the ratio of the distance to the screen (throw) to the screen width.

0

0,2

0,4

0,6

0,8

1

1,2

1,4

1,6

1,8

2

0,3 0,5 0,7 0,9 1,1 1,3 1,5 1,7 1,9 2,1 2,3 2,5 2,7 2,9 3,1 3,3 3,5 3,7 3,9

Hazard Distance [m]

Throw Ratio

Hazard Distance in function of modifying optics: ORION

15

3 What is in the box?

Projector

Power Cable (Country Dependent)

Remote Control

User Documentation

Projector Mounting Kits

Exhaust air kit (for ceiling mount):

A: Air-inlet filter

(also sold separately)

B: Side cover/Air-inlet
C: Ceiling mount cover/Air-outlet

(also

sold separately)

D: Exhaust air duct*

*Flexible hose (2m) with clamp included

Acoustic silencer kit (for ceiling mount):

B: Side cover/Air-inlet
C: Ceiling mount cover/Air outlet

Check that all components are in place and undamaged when unpacking the unit. Contact Barco
immediately if items are missing or damaged.

Save original packaging materials for use with future shipping or transport.

A

C

B

D

16

17

4 Installation

4.1 System considerations

Chapter 5, Overview, provides more information on the various features of the projector.

Safety first: Projectors and other equipment that are not mounted properly represent
a potential danger to people and may result in injury or death!

Installation should only be performed by trained and experienced personnel in order to achieve the desired
results.

Creating a successful system installation requires proper skills, competencies and knowledge of the particular
system requirements. In addition to knowing the expected performance, ambient conditions and all the
components that form the complete system, including Image Generation (IG), cabling, control system, screens
and projectors.

An installation may consist of multiple projectors, long cables and several IG, as well as intermediate system
components like signal converters and line buffers. Consideration should be taken to ensure that:

• IGpropertieslikepixelresolutionandframerefreshmatchthoseoftheprojector

• Choiceofsignalinterfaceandcablelengthsmatch.

o HDBaseT and 3G-SDI are so called long-haul interfaces, suitable for bespoke installation

on the premises using relatively long cables.

o DP, HDMI, DVI and VGA are all short-haul interfaces using pre-assembled cables with

limited cable lengths. Using extended cable lengths may result in reduced image quality
as well as loss of control information such as EDID (Extended Display Information Data).

• Signalampliers,switchesandothercomponentsshouldconveyEDIDandothercontrol

information. However, unfortunately many times EDID data is lost in translation under way,
potentially resulting in images of reduced pixel resolution and wrong aspect ratio.

A successful installation takes all relevant parameters into account to achieve great imagery!

18

4.2 Ventilation

Minimum safety distance to any side of the unit is 50 cm / 20” in any direction.

Hot air is exhausted from the rear vent. Do not place objects that are sensitive to heat closer than 50 cm
/ 20” to the exhaust vent.

Figure 4-1. Positioning the projector

When the projector is ceiling mounted using an exhaust air kit* (accessory) the minimum distance between
projector and roof is 15 cm.

4.2.1 Ventilation accessories

A set of optional accessories is available for this projector, covering anything from cables and lenses to air flow
parts and lens control. For more information visit www.barco.com or contact your preferred Barco representative.

50 cm

15 cm*

50 cm

50 cm

19

4.3 Ceiling and rig mounting

Use the three mounting holes on the projector underside to securely fix the projector to a ceiling or rig mount.

Use M6 screws that extend maximum 9 mm into the projector body.

Figure 4-2. Ceiling/rig mounting holes

4.4 Locking the projector

The projector can be physically locked using a Kensington lock. The Kensington lock hole, where the lock itself is
attached, is located on the back of the projector. Use an approved locking cable to secure the projector to a solid
object.

4.5 Projector angle (tilt)

The projector should be tilted maximum +/- 20 degrees from level (flat/ceiling) position. It can be rotated
360 degrees around the lens axis.

Tilting at higher degrees may reduce lamp life and increase the probability of overheating the projector.
Installation outside these specifications can void the guarantee.

Figure 4-3. Tilting angles

-20

o

+20

o

360

o

20

4.6 Selecting a lens

The projector is delivered without a lens, enabling you to select a lens according to your desired image size and
projection distance. The projector uses a bayonet mount system to precisely fix the lens in place. The lenses are
manual, meaning zoom, focus and iris adjustments are done by hand manually. Lens shift is motorized (horizon­tally and vertically).

Use only original lenses or lenses that are approved for use with this projector.

Figure 4-4. The protection lid

A protection lid is mounted on the projector lens opening to protect the interior of the projector from
dust and damage. The protection lid must always be in place whenever there is no lens mounted on the
projector!

The protection lid must be removed before attaching a lens!

The projection lenses are supplied with protection caps on both the entry and exit sides. Please keep the
caps on until mounting the lens on the projector!

Figure 4-5. Projection lens release button

4.6.1 Inserting a lens

1. Remove the protection lid on the projector by turning the lid anti-clockwise until it
comes loose

2. Remove the protection lids from the lens

3. Insert the lens, making sure the red line marking on the lens points straight up towards the top of the
cabinet. If the lens does not enter on the first attempt, retract the lens and try again from a slightly different
angle. Do not use force!

4. When the lens enters all the away in, firmly twist the lens clockwise until it clicks into position

Protection lid

Release button

21

4.6.2 Changing/removing a lens

1. Press in the lens release button

2. Twist the lens firmly anti-clockwise until it can be pulled gently out

3. Remove the existing lens and put the 2 lens projection caps back on the removed lens

4. Replace with another lens, or if no lens is to be installed, remount the projector protection lid

Note that the lens positioning when using lens shift may affect the accessibility of the lens button. If so,
reposition the lens to gain access.

4.6.3 Lens range

The table shows a selection of lenses available. Visit www.barco.com for the most up to date lens specifications.

ITEM TYPE THROW RATIO

(WQXGA)

F# f (mm) RANGE (m)

EN51 Zoom 1.71-2.37:1 2.60-3.09 33.9-46.5 1.5-10

EN52 Fixed 0.99:1 2.60 19. 7 1.0-10

EN53 Fixed 0.79:1@1.65 m 2.60 15.8 0.8-3. 3

EN54 Zoom 2 .68-4.18:1 2.60-3.26 52.6-81. 5 5-25

EN55 Zoom 0.86-1.16:1 2.50-2.72 17.2-23.1 0.8-5.0

EN56 Zoom 1.14-1.74:1 2.50-2.72 22.8-34.7 1.3-7.0

4.7 Lens lock

A lens-lock feature is available whereby three screws on the lens barrel are used to permanently fix the zoom,
focus and iris positions. For information on locking the adjustment rings in one position, please refer to section

4.10 Zoom, focus and iris.

22

4.8 Lens shift

Most of the Orion projection lenses can shift horizontally and vertically. However, some lenses, typically
wide angle lenses (on-axis type) have very little shift range.

Lens shift is motorized. To activate Lens Shift press the OK button on the keypad and then use the arrows on the
remote or keypad to shift the lens.

To use the RS-232 or LAN control interfaces, please refer to the relevant SIS (Simplified Instruction Set) commands
available for download on www.barco.com

4.9 Lens planarity (Scheimpflug adjustment)

This adjustment is rarely needed, do not apply it unless it is required.

Certain applications require fine adjustment of the lens planarity in order to obtain an image that is focused. The
projector is fitted with three adjustment screws (Allen key 3 mm/5 mm) around the bayonet mount that facilitate
a Scheimpflug adjustment. Do not attempt adjusting without the required technical competence and refer to the
service manual found on our web for further info.

Figure 4-6. Scheimpflug Adjustment Screws

23

4.10 Zoom, focus and iris

These lens functions are manual (not motorized).

• Adjust zoom to achieve the desired image size (if the lens has a zoom-function).

• Then adjust focus to achieve a sharp image. If the image is not sharp all over the surface, please check the

surface flatness and whether the lens axis is perpendicular to the projection surface.

• Use the iris to adjust the contrast and focus depth of the image. Adjusting the iris will affect the brightness;
stopping the iris down increases contrast and image depth, but reduces brightness.

• The zoom, focus and, iris rings can be locked in position to prevent picture settings being accidentally
changed. Use a 1.5 mm Allen key to tighten the Z-lock screw on each ring to lock the movement until the
rings cannot be turned.

Figure 4-7. Positioning of Zoom, Focus and Iris rings (may vary on some lenses)

Zoom

Iris

Focus

24

4.11 Making the connections

The projector is equipped with multiple signal and control interfaces to support various video and data sources
(see connector panel below), as well as different control systems.

Always make sure that the projector is powered off before connecting any signal and/or control cables.

Long cables may cause distorted or even failing signal quality. Always make sure best quality cables are
used, and take into consideration the cable length limitations applying to the various interface standards.

4.12 Connecting video and data sources

Choice of connectivity depends on the installation requirements as well as the sources connected. Generally,
digital interfaces are preferred over analog. Multiple signals can be connected in parallel to allow for a selection
of sources to be viewed in sequence.

4.13 Connecting control interfaces

Power off the projector and the source

Choice of control interface depends on the installation requirements. Attach the interfaces of choice and make
sure all connectors are fully inserted and retained.

Visit www.barco.com to download the relevant SIS (Simplified Instruction Set) commands or for more
information.

Power up the projector and the source

4.14 Source format integrity – EDID

If using 3rd party system equipment, such as signal repeaters or switchers, please make sure that EDID
(Extended Display Identification Data) information is not lost in translation. Wrong EDID data may result in
distorted images, wrong aspect ratios or reduced image resolutions.

25

4.15 Image sizes

Lens types and specifications may change without prior notice.
For correct lens information please visit www.barco.com

1920 x 1200/1920 x1080 (WUXGA/1080)

Ultra Wide Fixed (EN53) 0.74 : 1 (0.8 - 3.3m)

Wide Angle (EN52) 0.92 : 1 (1.0 - 10m)

Long Throw Zoom (EN54) 2.68 - 4.18 : 1 (5 – 25m)

Projection distance

Image width

m

12.00

11.00

10.00

9.00

8.00

7.00

6.00

5.00

4.00

3.00

2.00

1.00

0

Screen diagonal

m

13.75

12.50

11.25

10.00

8,75

7.50

6.25

5.00

3.75

2.50

1.25

0

0.00

0.50

1.00

1.50

2.00

2.50

3.00

4.00

4.50

5.00

5.50

6.00

6.50

3.50

0

10

20

Super Wide Zoom (EN55) 0.80 - 1.08 : 1 (0.8 - 5.0m)

Wide Zoom (EN56) 1.06 - 1.62 : 1 (1.3 - 7m)

Standard Zoom (EN51) 1.60 - 2.21 : 1 (1.5 - 10m)

26

2560 x 1600/ 2560x1080 (WQXGA /Panorama)

Lens types and specifications may change without prior notice.
For current information visit www.barco.com

Ultra Wide Fixed (EN53) 0.79 : 1 (0.8 - 3.3m)

Wide Angle Fixed (EN52) 0.99 : 1 (1.0 - 10m)

Long Throw Zoom (EN54) 2.68 - 4.18 : 1 (5 - 25m)

Super Wide Zoom (EN55) 0.86 - 1.16 : 1 (0.8 - 5.0m)

Standard Zoom (EN51) 1.71 - 2.37 : 1 (1.5 - 10m)

Wide Zoom (EN56) 1.14 -1.74 : 1 (1.3 - 7m)

Projection distance

Image width

Screen diagonal

15.00

13.75

12.50

11.25

10.00

8,75

7.50

6.25

5.00

3.75

2.50

1.25

0

0.00

0.50

1.00

1.50

2.00

3.00

4.00

4.50

5.00

5.50

6.00

6.50

7.00

7.50

3.50

25

0

10

20

m

m

2.50

12.00

11.00

10.00

9.00

8.00

7.00

6.00

5.00

4.00

3.00

2.00

1.00

0

27

5 Overview

Figure 5-8. Projector front

Figure 5-9. Projector rear

Figure 5-10. Projector top

Remote Control Receiver

Interchangeable Projection Lens

Projection Lens Release Button

Mains Power Connector

Hot Air Exhaust

Signal and Control Connector Panel

Remote Control Receiver

Keypad

28

Figure 5-11. Mounting features

Figure 5-12. Projector left and right hand side

Lamp Door

Air Inlet

Ceiling/Rig Mounting Features

Accessory Mounting Features

29

5.1 Keypad and indicator

Figure 5-13. Projector top key pad

KEY VALUE

POWER Power on or power off (standby)
MENU Activate or deactivate on-screen menu system
UP, DOWN, LEFT, RIGHT Select source when not in Shift or Menu mode

Shift lens when not in Menu and after SHIFT/OK pressed
Navigate when in Menu system

SHIFT/OK Shift lens when not in menu system

Shift option when in menu system

AUTO Automatic set-up

STATUS COLOR

On (active)

Blue (solid)

Wait on Blue (flashing)

Standby (off) Yellow (solid)
Wait Yellow (flashing)
Lamp failure Red (solid)
Overheating Red (flashing)
Configure/upgrade Yellow (rapid flashing)
Error Red (rapid flashing)

Indicator light

Power on/off

Menu

Left

Right

Up

Down

Shift/OK

Back

30

5.2 Wireless remote control

Figure 5-14. Remote control

BUTTON FUNCTION

POWER Turns projector ON/OFF
INFO Shows Status menu; info on numbers & versions, lamp info

*

Activates the projector auto settings

SHIFT Activates lens shift function

#

Reserved for future use

OK/ARROWS Confirms the selection / Directional navigation tools
BACK Returns to previous alternative
MENU Activates the projector menu
SOURCE Toggles between available sources (forward/backwards arrows)

SOURCE

POWERINFO

SHIFT

MENU

BACK

i

OK

Batteries can be replaced by end-user.
To replace the 2 standard AAA-batteries for
this remote control, slide the lid at the back
of the control downwards. Lift it off and
remove the batteries. Replace with new
batteries and slide the lid back in place.

31

5.3 Connectors

Figure 5-15. Connector panel (see technical data for details)

5.3.1 Signal connectors

CONNECTOR
NAME

CONNECTOR
TYPE

FUNCTION

HDBaseT RJ45 Video over twisted pair
DVI DVI-I*) dual link Digital video (dual-link)
HDMI HDMI type A Digital video

DP (DisplayPort) DP Digital video (2)
VGA 9 pin mini D-sub Analog RGBHV video
3G-SDI BNC 75 Ω Digital Video

*) the DVI connection is digital-only, although it uses the DVI-I physical connector for convenience

5.3.2 Control connectors

CONNECTOR
NAME

CONNECTOR
TYPE

FUNCTION

SYNC1 BNC Multipurpose bi-directional synchro-

nization port

SYNC2 BNC Multipurpose bi-directional synchro-

nization port

SYNC3 3-pin mini-DIN Powered multi purpose bi-direction-

al synchronization port

USB A USB A USB connectors for SW upgrade and

diagnosis

LAN RJ45 Control

RS232 9 PIN DSUB Control

32

5.4 Menu system

The various projector-settings can be controlled via the on-screen menu system. The menu system is accessed by
the keypad on the projector or using the wireless remote control.

Press the MENU key to enter or leave the menu system. Navigate the options using the arrow-keys. Select option
with the OK key.

The menu-system will be referenced throughout the user guide. Please familiarize yourself with the menus and
the rich functionality provided.

5.4.1 Top menu

3D: 3D and dual head setup

picture:

Basic and advanced picture controls.

installation: System controls and information.

settings: Settings that affect how the projector behaves or interacts with third party devices, such as

networks and control systems

language:

Selects menu language.

status: System information.

The top level menu item 3D is only visible for Active Stereo 3D enabled projectors.

33

5.5 3D main menu

The 3D menu contains settings for turning 3D on and off, in addition to defining various aspects of setup using
Dual Head and specifying the types of glasses to be used.

3D :

Offers the possibility to switch the 3D function off and to choose between the following

alternatives for setup: off, side by side (<60Hz only), frame sequential and dual head
(<60Hz only)

dual head setup:

Allows the user to select left eye and right eye input sources. Some combinations of

left/right eye are not possible, see table on next page.

3D glass sync delay:

Here you can set the delay time for your 3D glasses on a range from 0-359°

swap eyes: Swap order of eyes (left/right) for 3D-glass synchronization.

34

5.5.1 3D > Dual head setup sub menu

source 1: Choice of source. Alternatives are SDI1, SDI2, DVI, HDMI, VGA, HDBaseT, DisplayPort1,

DisplayPort 2. For possible setup combinations, see Figure 5-18. Dual head setup
possibilities.

source 2:

Choice of source. Alternatives are SDI1, SDI2, DVI, HDMI, VGA, HDBaseT, DisplayPort1,

DisplayPort 2. For possible setup combinations, see Figure 5-18. Dual head setup
possibilities.

Figure 5-16. Dual head setup possibilities

DP1 DP2 HDBaseT DVI(SL) HDMI DVI (DL) VGA 3G SDI

(A)

3 G SDI
(B)

DP1

DP2

HDBaseT

DVI (Single Link Mode)

HDMI

DVI (Dual Link Mode)

VGA

3G SDI (A)

3G SDI (B)

Not possible

Possible

35

5.6 Picture main menu

Picture menu adjustments are global and stored independently of source. The exception is 2D/3D where profiles
are stored individually.

profile:

A selection of predefined profiles with different attributes: standard, presentation, bright, video,

cinema, DICOM, SRP, custom, advanced (only available if enabled from service menu). If the
profile is marked by an asterisk (*), this indicates that the original settings have been changed.

RealColor: Barco’s proprietary color management suite. See RealColor sub menu.

gamma:

10 predefined gamma curves:

Film 2.2: Exponential 2.2 curve

Film 2.4: Exponential 2.4 curve

Film 2.6: Exponential 2.6 curve

Film 2.8: Exponential 2.8 curve

Video 1: Relaxed S-shape

Video 2: Increase S-shape

Computer 1: Steep S-shape

Computer 2: Very steep S-shape

Dynamic: Increase S-shape

DICOM 180 Lux: Curve shape depending on type of color wheel used. Further DICOM

curves are shown in menu profile

lamp power: Adjustment of lamp power between 280-350W

profile reset: Resets any entered profiles, either current or all, to default

brightness: Electronic image brightness. Range -50 to +50

contrast: Electronic image contrast. Range -50 to +50

saturation: Electronic image saturation. Range -50 to +50

aspect: Aspect ratio of image scaling. 5 options:

Fill aspect ratio: Fills the imaging device in horizontal and/or vertical direction to main the input
image aspect ratio.

Fill all / 16:9 / 4:3: Fills the entire imaging device regardless of input aspect ratio and resolution.

One-to-one: Shows input image mapped pixel-by-pixel without scaling on the imaging device.

advanced:

Advanced features. See Chapter 5.6.2.

reset: Restore picture settings to factory default.
source information: Detailed information about the acquired source.

36

5.6.1 Picture > RealColor sub menu

BrilliantColor™: Texas Instruments DLP™ color processing.

Bright: Max brightness, boosted color profile for highest perceived brightness. In this
mode all segments and spokes of the color wheel are in use.

Color: Max brightness, balanced color profile for better color performance. In this
mode all segments and spokes of the color wheel are in use.

Auto:

Only available in 3D

Off: In this mode the spokes (transition between segments) and all secondary
segments (cyan and white) and on color wheel are off. Less color and brightness boost
will reduce image noise.

SRP™ Half: Smear Reduction Processing (factor 1:2), VizSim / VizSim bright only

SRP™ Full™: Smear Reduction Processing (factor 1:1), VizSim / VizSim bright only

color correction:

Enable or disable color correction.

desired values: Desired mode (RGB, RGBCMY) for RealColor; manual specification of red, green blue,
cyan, magenta, yellow and white (if in coordinates mode) coordinates (x,y) color and
gain.

Reset all to native: Resets all to measured values/projector native

white Determines method for setting of the white point; temperature of x-/y-coordinate.

temperature:

Sets the system color temperature (white point) on the Kelvin scale from 3200K to
9300K in steps of 100K. All color temperatures are tracked on the black body curve. The
exact coordinates for the temperature will be shown in coordinates (x,y) when adjusting
the temperature.

x-coordinate: Sets the X co-ordinate of the white point.

y-coordinate: Sets the Y co-ordinate of the white point.

reset to D65: Reset the white point to D65 coordinates.

reset to native: Resets white point to measured values.

RealColor calibration: Selects color calibration test images (off, uncorrected red/green/blue/full white) and

color processed test images (red, green, blue, white, black, cyan, magenta, yellow).
Presents measured values for RealColor. Calibration settings must be made individually
for each separate profile.

37

5.6.2 Picture > Advanced sub menu

horizontal position: Shifts the image sideways (VGA only)

vertical position: Shifts the image up or down (VGA only)

phase

: Adjust for stable image. A jittery image may appear with certain VGA sources. You may

also press the AUTO button on the keypad or remote control
to optimize.

frequency:

Adjust image width. An incorrect setting may produce vertical, unstable bands in the

image, and parts of the image may not be displayed on screen. Push the AUTO button
to find a correct setting, or manually adjust the frequency until the vertical bands
disappear. Frequency adjusts the pixel clock sampling frequency

color space:

Enables selecting between Auto, RGB, YCbCr 601, YCbCr 709

input level: Choice between; auto, computer, video. Depending on source select between 0-255

(computer), 16-235 (video).

source correction:

Gives access to individual brightness offset settings (see below).

In addition you can start the AD calibration process which requires VGA source which
displays a Grey16 image (right hand image below).

cropping:

Adjust vertical position of picture to reduce letterbox bars or improve onscreen

composition. Default setting is disabled. Three crop modes are available:

Preset: the picture is altered without contraints to fill a preset display aspect

Auto: the projector analyzes the top of the picture for letterbox bars, calculates and

applies a crop coordinate from this data. Auto crop is identical for the top and bottom
of the picture.

Manual: the user manually enters the number of lines (top and/or bottom) to be

cropped from the picture.

reset to native:

Resets white point to measured values.

38

5.7 Installation main menu

image orientation: Rotate image in desktop front, desktop rear, ceiling front, ceiling rear.
source scan

: Search all input connectors for an active signal or stay on one connector.

IR front

Enable or disable front IR-receiver.

IR rear

Enable or disable rear IR-receiver.

OSD enable: Sets how the OSD messages should appear.

On: All OSD messages are shown.
Only warnings: Only critical OSD messages are shown.
Off: No OSD messages are shown. The OSD menu is still accessible by clicking menu

on either the remote or the keypad.

test image:

Displays internal test images for projector alignment and setup. Selected ratio display

is shown in the center of the test image (white fill).

4:3; 16:9; 16:10; 1.85:1; 2.35:1; 5:4;
Combined: fills the imaging device with a white image and marks out the all of the

above aspect ratios.

sync termination VGA

: Enable sync termination to 75 Ω /2.2 kΩ

sync termination SYNC1

: Enable sync termination to 75 Ω /2.2 kΩ

sync termination SYNC2

: Enable sync termination to 75 Ω /2.2 kΩ

sync termination SYNC3

: Enable sync termination to 75 Ω /2.2 kΩ

DisplayPort 1 eq Choice between Normal, High, Low (enables receiving signals via longer cables/

with higher bit rate)

DisplayPort 2 eq Choice between Normal, High, Low (enables receiving signals via longer cables/

with higher bit rate)

picture by picture Show two sources side by side
picture by picture setup Choose the two sources to be shown side by side
EDID

: Sub menu for EDID, see chapter 5.7.1.

synchronization: Sub menu for synchronization see chapter 5.7.2 .

39

5.7.1 Installation > EDID sub menu

VGA: Define the detailed timing descriptor in the EDID data for VGA connector.

Select between auto, WUXGA, 1080@60 Hz, SX+, SXGA, 1366x768, 720@60 Hz,
720@50 Hz, XGA, SVGA, VGA.

DVI

: Define the detailed timing descriptor in the EDID data for DVI connector.

Select between auto, WQXGA @ 60Hz, WUXGA@120Hz, WUXGA @ 60Hz,1080@20Hz,
1080@60 Hz, SX+, SXGA, 1366x768, 720@60 Hz, 720@50 Hz, XGA, SVGA, VGA. Here
are the auto-settings for various projectors:

• 1080projector: 1920x1080@120Hz.Duallink

• WUXGAprojector: 1920x1200@120Hz.Duallink

• WQXGAprojector: 2560x1600@60Hz.Duallink

HDMI: Define the detailed timing descriptor in the EDID data for HDMI connector. Select

between auto, WUXGA@60 Hz, 1080 @60 Hz, SX+, SXGA, 1366x768, 720@60 Hz,
720@50 Hz, XGA, SVGA, VGA. All settings, except auto, uses DVI as type. Here are the
auto-settings for various resolutions:

• 1080projector: 1920x1080@60Hz

• WUXGAprojector: 1920x1200@60Hz

• WQXGAprojector: 1920x1200@60Hz

HDBaseT: Define the detailed timing descriptor in the EDID data for HDBaseT connector.

Select between auto, WUXGA@60 Hz, 1080@60 Hz, SX+, SXGA, 1366x768, 720@60 Hz,
720@50 Hz, XGA, SVGA, VGA. All settings, except auto, uses HDMI as type. Here are
the auto-settings for various resolutions:

• 1080projector: 1920x1080@60Hz

• WUXGAprojector: 1920x1200@60Hz

• WQXGAprojector: 1920x1200@60Hz

DisplayPort 1: Define the detailed timing descriptor in the EDID data for DisplayPort 1 connector.

Select between auto, WQXGA@120 Hz, WQXGA@60 Hz, WUXGA@120 Hz, WUXGA@60
Hz,1080@120 Hz, 1080@60Hz, SX+, SXGA, 1366x768, 720@60 Hz, 720@50 Hz, XGA,
SVGA, VGA. Here are the auto-settings for various resolutions:

• 1080projector: 1920x1080@120Hz

• WUXGAprojector: 1920x1200@120Hz

• WQXGAprojector: 2560x1600@120Hz

DisplayPort 2: Define the detailed timing descriptor in the EDID data for DisplayPort 2 connector.

Select between auto, WQXGA@60 Hz, WUXGA@120 Hz, WUXGA@60 Hz,1080@120Hz,
1080@60 Hz, SX+, SXGA, 1366x768, 720@60 Hz, 720@50 Hz, XGA, SVGA, VGA. Here
are the auto-settings for various resolutions:

• 1080projector: 1920x1080@120Hz

• WUXGAprojector: 1920x1200@120Hz

• WQXGAprojector: 2560x1600@60Hz

* The following Picture by Picture-usage options are available for some models:

960x1080@60 Hz/120 Hz, 960x1200@60 Hz/120 Hz, 1280x1600@60 Hz/120 Hz

40

5.7.2 Installation > Synchronization sub menu

2D frame lock: Selects the 2D frame lock sync signal. Options for 2D frame lock: source, SYNC 1, SYNC

2, SYNC 3.

SYNC 1: Selects usage of SYNC1 connector in 2D mode. Options for SYNC 1: input, display sync,

SYNC 2, SYNC 3

SYNC 2: Selects usage of SYNC2 connector in 2D mode. Options for SYNC 2: input, display sync,

SYNC 1, SYNC 3

SYNC 3: Selects usage of SYNC3 connector in 2D mode. Options for SYNC 3: input, display sync,

SYNC 1, SYNC 2

3D source sync: Selects the 3D source LR sync signal. Options for 3D source sync: source, SYNC 1, SYNC

2, SYNC 3

3D display sync: Selects the 3D display LR sync signal. Options for 3D source sync: source, SYNC 1, SYNC

2, SYNC 3

SYNC 1: Selects usage of SYNC1 connector in 3D mode Options for SYNC 1: input, display sync,

glass sync, SYNC 2, SYNC 3

SYNC 2: Selects usage of SYNC2 connector in 3D mode Options for SYNC 2: input, display sync,

glass sync, SYNC 1, SYNC 3.

SYNC 3: Selects usage of SYNC3 connector in 3D mode Options for SYNC 3: input, display sync,

glass sync, SYNC 1, SYNC 2

If you use one of the sync connectors as 2D or 3D sync input, this may block the use of the same connec­tor as output. For more information on possible user scenarios, visit www.barco.com

41

5.8 Settings main menu

PIN code: Protect the projector from usage with a PIN. If enabled the projector will ask for the

PIN at every start up.

network: Set IP address, Subnet mask and default gateway TCP/UDP port number.

DHCP is supported and is enabled by default, but can be disabled.

factory reset: Restore all settings to the factory defined values.

service: End user protected settings. Access PIN code required.

standby ECO mode Power saving mode sending the projector into a deep sleep setting when in standby.

Wake up can be performed either by pressing the power button on the projector/
remote control or remotely via the RS232 connector using the ASCII protocol / wake on
LAN via the Ethernet. If DPMS is enabled and a source signal becomes active again the
projector will return to normal operation.
When in standby ECO mode, the baud rate of the RS232 communication is fixed at

19200.

DPMS: Enable or disable DPMS power saving. This feature is used to automatically power

down the projector if no source is detected for a given period of time (defined
by DPMS timeout). If the projector is powered down in DPMS power save, it will
automatically power back on if a valid source is acquired.

DPMS timeout: Set the period of time before the projector automatically enters DPMS mode. DPMS

must be enabled for this menu item to activate.

LED indicators mute: Disable all LED indicators on top of the projector. A critical error (status LED flashing

RED) will still be enabled.

menu timeout: The time interval before the OSD is automatically disabled. Option of “never” is

available if the OSD is never to time out.

background: Gives a choice between white, gray or black background color.

splash: Enable or disable manufacturer logo or black for the startup splash screen.

baud rate: Presents alternative baud rate settings:

4800, 9600, 19200, 38400, 57600, 115200

42

5.8.1 Settings > Pin Code sub menu

PIN code enable: The PIN code is disabled by default. If you want to enable/disable the PIN code you

have to enter the current PIN (Default PIN: 1234). f PIN is entered incorrectly 3 times,
it will ask for a PUK code, which is provided in printed form in the box. If the PUK is
entered incorrectly it will require a special unlock code provide by a service partner to
unlock the projector.

change PIN code: To change the PIN code you first have to enter the current PIN code (Default PIN:

1234). Then you enter a new 4 digit code and confirm this code by entering the same
code again. Click OK and the new code is set.

43

5.8.2 Settings > Network sub menu

change LAN settings: In this sub-menu you can switch the DHCP enabled function on or off.

If off you can set a fixed IP-address.

LAN DHCP: DHCP is supported and is enabled by default, but can be disabled under change LAN

settings

LAN IP address:

Info field stating the current LAN IP address.

LAN subnet mask: Info field stating the current LAN subnet mask.

LAN default gateway: Info field stating the current LAN default gateway.

44

5.8.3 Settings > Factory Reset sub menu

picture: Restores picture settings to factory default.

3D: Restores 3D settings to factory default.

communication: Restores communication settings to factory default.

RealColorTM: Restores RealColor

TM

settings to factory default.

other: Restores other settings of your choice to factory default.

5.8.4 Settings > Service sub menu

service: Restricted area with information intended for qualified service personnel only

enter code: Enter the 5-digit access code to gain access to the service information.

45

5.9 Languages main menu

Select the desired menu language.

• Supported languages: English, French, German, Spanish, Norwegian, Swedish, Russian, Korean, Japanese,
Chinese Traditional, Chinese Simplified, Portuguese, Italian.

• Default: English

46

5.10 Status main menu

source information: Simple and advanced source information.

synchronization
information: Displays the current synchronization information. Includes 2D framelock, 3D

source sync and 3D display sync.

part number: Projector part number.

serial number: Projector serial number.

manufactured (y): Year of manufacturing.

manufactured (w): Week of manufacturing.

software version: Software version installed in the projector.

This is very important for service requests.

colorwheel:

Type of colorwheel installed.

lamp remaining: Remaining lamp time.

lamp time: Lamp time used.

total operating: Total operating time for projector.

lamp power: Lamp power in watts.

IP address LAN: Projector LAN IP address for use in network/remote control.

47

5.10.1 Status > Source Information sub menu

advanced: Access to sub menu for more settings depending on source used.

See 4.10.2 Status > Source Information > Advanced sub menu

source 1: Info on which source is in use.

format: Displays resolution and frequency for the source in use.

source 2: Info on which source is in use.

format: Displays resolution and frequency for the source in use.

brightness: Info on brightness settings.

contrast: Info on contrast settings.

saturation: Info on saturation settings.

gamma: Info on gamma-variant used.

48

5.10.2 Status > Source Information > Advanced sub menu

resolution: Info on current source resolution.

total image size: Info on current horizontal and vertical image size.

sync frequency : Info on current horizontal and vertical sync frequency for the projector.

pixelclock: Week of manufacturing.

scan: Projector serial number.

mode id: Info on current mode setup (VGA source only).

chroma sampling: The current source chroma sampling type. Typically 4:4:4 or 4:2:2.

bits per channel: The number of bits per channel. For instance, for a 24 bit RGB source, the number of

bits per channel is 8.

49

5.10.3 Status > Source Synchronisation sub menu

3D: Indicates which 3D mode is used.

2D frame lock: Indicates what the projector locks to in 2D

frequency: Shows the current frequency of the locking signal

status: Indicates the locking status

phase: Indicates phase between the source and the locking signal

3D source sync: Indicates where the source L/R sync is connected

source has in-band sync: Indicated if the source has embedded L/R sync, only

supported on DisplayPort

frequency: Shows the current frequency of the signal

duty cycle: Shows the duty cycle of the signal

status: Indicates the sync status

phase: Indicates phase between the source and the L/R sync signal

3D display sync: Indicates what the projector locks to in 3D

frequency: Shows the current frequency of the locking signal

duty cycle: Shows the duty cycle of the signal

status: Indicates the locking status

phase: Indicates phase between the source and the locking signal

50

51

6 Functionality

6.1 Powering On and Off

6.1.1 Manual power control

Switch the projector between On and Standby using the POWER switch on the keypad or the wireless remote
control.

The keypad STATUS indicator is blue when the projector is up and running, flashing yellow when cooling down
and yellow when in standby. No status light indicates that the power has been switched off completely in the
installation.

6.1.2 DPMS - power down

This is a power down mode which needs to be activated in the SETTINGS menu.

When activated it powers down after a specified period of time after a source has been removed. The time out
setting can be specified in the DPMS TIMEOUT function in the same menu, using the arrow keys. If the projector
is powered down in DPMS power save, it will automatically power back on if a valid source is acquired.

6.1.3 Standby ECO mode

Power saving mode sending the projector into a deep sleep setting when in standby. Wake up can be performed
either by pressing the power button on the projector/remote control or remotely via the RS232 connector using
the ASCII protocol / wake on LAN via the Ethernet. If DPMS is enabled and a source signal becomes active again
the projector will return to normal operation.

When in standby ECO mode, the baud rate of the RS232 communication is fixed at 19200.

6.2 Image alignment

Test images are built into the system for easier alignment of the projector

To access the test images, go to the menu entry INSTALLATION > TEST IMAGE. Run through the various test im-
ages using the arrow keys. When a test image matching the aspect ratio of your screen has been found, you can
match the screen using the zoom, focus, lens shift and aligning the projector physically.

6.2.1 Image orientation

The projector supports the following installation orientations (in relation to the screen):

• Desktop front (default)

• Ceiling front

• Desktop rear

• Ceiling rear

To set the image orientation go to menu entry INSTALLATION > IMAGE ORIENTATION.

52

6.3 Language

The menu system default language is English.

The available languages are:

• English

• French

• German

• Spanish

• Russian

• Norwegian

• Swedish

• Korean

• Japanese

• Chinese Simplified

• Chinese Traditional

• Portuguese

• Italian

To change the language of the menu system, click top menu and select your desired language.

6.4 System status

System status can be read at any time. STATUS is easily accessible from the top menu or by pushing the INFO
button the wireless remote control.

• Part number

• Serial number

• The year/week the projector was manufactured

• Current software version

• Runtime and remaining time for lamp

• Total number of operating hours

• All network information

• Currently active source

Further source information is available by selecting STATUS > SOURCE INFORMATION.

If a deeper analysis is required for the currently active source, select STATUS > SOURCE INFORMATION > AD
VANCED. This menu provides detailed timing information for the currently active source.

Setting custom color space and digital level

The projector will automatically try to set the correct color space and digital drive level based on information from
the source.

For manual override of the automatically detected color space and digital level, go to PICTURE > ADVANCED in the
menu. Set the COLOR SPACE and INPUT LEVEL to one of the manual settings, choosing your desired color space
and digital drive level.

53

6.5 Lamp power

The projection lamp can be run at different power levels. Higher levels give higher brightness and shorter lamp
life time. Lower levels save energy, extend lifetime and reduce brightness. In the menu system, go to PICTURE >
LAMP POWER and adjust the setting according to need.

6.6 Source selection, source scan

The projector can automatically scan through all the input connectors for a valid signal. If a valid signal is found,
the image will set up automatically. This is called source scan.

Source scan is by default disabled. When source scan is disabled, the projector will only display the selected
source. Use the keypad, remote control or the control interface to change the selected input source. In the menu
system, go to INSTALLATION > SOURCE SCAN.

Direct source selection can be done using the keypad or the wireless remote control.

• Using the keypad, press the arrow keys to select desired source (when not in menu and not shifting the
lens)

• Using the wireless remote control, press the desired dedicated source select button

• Using the RS232 or LAN control interfaces, please see the relevant SIS (Simplified Instruction Set) commands

available to download on www.barco.com

•

6.7 On screen display (OSD) messages

When detecting sources and using the various features of the projector, OSD messages will appear on the screen.
Which messages will be appearing can be partially controlled by the user. The OSD can run in these modes:

• On. All messages, warnings and information is displayed.

• Off. No messages are shown.

• Only warnings. Only critical warning messages like temperature overheating will be shown.

Go to menu entry INSTALLATION > OSD ENABLE to control the OSD behavior.

6. 7.1 Disabling the STATUS indicator

In certain installations it may be necessary to completely disable the STATUS indicator in the keypad. Disable the
indicator in the menu SETTINGS > LED INDICATORS MUTE.

6. 7. 2 Setting the background color

The background color displayed when the projector is searching for a source can be set to a set of predefined
colors (white/grey/black). Go to menu entry SETTINGS > BACKGROUND to set the desired color.

6. 7. 3 Setting OSD menu timeout

If the OSD menu is open and not used for a defined period of time, it will automatically be disabled. This timeout
interval can be regulated from 5 seconds to 60 seconds, with the default time set to 30 seconds. The timeout
can also be set to NEVER for the OSD menu to never time out. Go to menu entry SETTINGS > MENU TIMEOUT to
change the time period.

54

6.7.4 Selecting the startup logo

When the projector is starting up, the manufacturer logo is displayed in the entire image. Setting the logo to
BLACK will disable the manufacturers default logo. Go to menu entry SETTINGS > SPLASH to change this setting.

6.8 Picture by Picture (PbP)

You may choose to view two sources simultaneously as a picture by picture.

The PbP-function allows viewing of two images side by side or on top of each other.

Certain restrictions apply to how sources combine when using PbP.

To view PbP:

• Enter the INSTALLATION menu and activate the PICTURE BY PICTURE function

• Move down to PICTURE BY PICTURE SETUP

• Set up by selecting the sources you want under SOURCE 1 & SOURCE 2

• The following special options are available for Picture by Picture-usage:

960x1080@60 Hz/120 Hz, 960x1200@60 Hz/120 Hz, 1280x1600@60 Hz/120 Hz,
depending on projector model, see 5.7.1 Installation > EDID sub menu

6.9 PIN code

The projector can be locked by a PIN (Personal Identification Number) code to control
access. The PIN code is 4 digits, and if the PIN code is activated, you must enter the
correct code to unlock the projector. Factory set PIN (1234).

To activate, deactivate or change the PIN code, see the SETTINGS > PIN CODE sub menu.

If an incorrect PIN code is entered, you may try again two times. If you fail three times in a row, entering
a PUK (unlock) code is needed. The PUK code is supplied with the product.

If you also fail three times with the PUK code, the projector locks up permanently, and can only be un­locked by a special service unlock code.

To access this code, you will need to contact your dealer or a service station. The service unlock code will be gen­erated based on a secure, encrypted number that is produced by the projector itself. The projector will produce a
new number every time.

In order to unlock the projector via a dealer/service station, proof of ownership must be provided by the
customer.

6.10 Disabling the wireless remote control (IR) receivers

The projector has 2 IR receivers, one in the front and one at the rear.

These receivers can be individually disabled if necessary. Go to menu entry INSTALLATION > IR FRONT / IR REAR
to disable the receivers.

55

6.11 Software upgrades

When upgrading the software the projector must always be in standby mode!

If you are or have been in standby ECO mode you MUST use the following procedure before upgrading your
projector:

1. Start the projector

2. Disable the standby ECO mode in the OSD menu

3. Power off (enters standby and not ECO mode)

4. Disconnect and reconnect the power cable

5. Wait for standby (yellow light)

6. Connect USB cable and proceed with the upgrading process below

To upgrade your projector software follow the method and sequence described below:

1. You will need a USB memory stick set up with a FAT-file system to perform this upgrade

2. Access the upgrade software from www.barco.com

3. Download and save the firmware.zip-file to your PC desktop

4. Download and save the firmware_<version>.tar file to the root of a memory stick

It is important that the USB is safely removed from computer using the eject
function on your PC.

5. Set the projector in standby mode

6. Insert the memory stick in the projector and wait a few seconds

7. If the projector is in standby mode it will start flashing automatically
If the projector is in a sleep mode, push the on button to initiate flashing
Rapid blue blinking indicates that upgrade is initiated

8. Remove the USB stick when blue blinking turns to yellow blink.
Rapid yellow blinking indicates that the upgrade process is running

9. Do not turn off projector/remove the power cable while the upgrade is still in progress!

10. The projector may restart several times during the upgrade

11. The upgrade has finished successfully when yellow rapid blink has changed to solid yellow light

56

57

7 Optimizing the image

This chapter outlines what image optimization features and functions are available for the projector and
gives some advice on how to best use these.

All color calibration is done using Barco’s RealColor™ solution.

7.1 Calibration data

All Barco projectors are measured and calibrated with high precision equipment at the factory for the best
out-of-box experience. Over the lifetime of the lamps the characteristics of the projector might change
slightly. The same applies when replacing lamps.

7.1.1 Updating RealColor™ calibration data

For accurate results with the RealColor™ system, accurate measurement data is required.

RealColor™ calibration data can be found under the menu entry PICTURE >REALCOLOR >REALCOLOR

CALIBRATION > MEASURED VALUES

X/Y and relative luminance values for red, green, blue, white and BrilliantColor™ 1 are entered in this menu.
The BrilliantColor™ should all be set to 0.000 for the VizSim (RGB) color wheel. All values can also be up­dated using the communications protocol over RS-232 or LAN.

Before setting these values, it is important to select the desired BrilliantColor™
setting. Go to menu entry PICTURE > REALCOLOR > BRILLIANTCOLOR to select
the desired BrilliantColor™ look.

Measurements must be done on the built in test patterns. This is in particularly important for the Brilliant­Color™ 1 test pattern since it is impossible to generate this pattern correctly using a computer source.
In the user menu these patterns can be accessed through PICTURE > CALIBRATION > REALCOLOR
CALIBRATION > COLOR CALIBRATION TEST IMAGE/COLOR PROCESSED TEST IMAGE.

Use the arrow keys to cycle through the images.

Performing a factory reset of the projector will restore the measured values to the
values measured in the factory.

When measuring data, a high quality measurement instrument is highly recommended for accurate
results. Spectrometers (like PhotoResearch PR-655) are preferred.

58

7.1.2 RealColor™ modes

Before any color correction is applied to the image, RealColor™ must be enabled. Go to menu PICTURE >
REALCOLOR > COLOR CORRECTION to enable RealColor™.

RealColor™ can operate in 3 modes:

• Color temperature/white point correction only.

• Red, Green, Blue, White correction. In this mode optimal color coordinates for Cyan, Magenta and Yel-

low will be computed automatically.

• Red, Green, Blue, Cyan, Magenta, Yellow, White. In this mode color points and intensity for each color
can be manipulated separately.

To change RealColor™ mode go to PICTURE > REALCOLOR > DESIRED VALUES > DESIRED CO-

ORDS MODE.

59

7.2 Setting a white point or color temperature

After enabling RealColor™ set the color temperature in the menu PICTURE > REALCOLOR > TEMPERA-
TURE. Values between 3200K and 9300K can be selected. These color temperatures are tracking the
“black body curve”- the black curved line in the center of CIE Chart in Figure 7-1. The default is the D65
illuminant at 6500K.

The white point can also be set to a custom value defined by an x, y coordinate not linked to the black
body. Go to menu PICTURE > REALCOLOR > X-COORDINATE and PICTURE > REALCOLOR > Y-
COORDINATE to change the white point.

Figure 7-1. CIE chart

7.2.1 Defining the system color gamut

All colors visible to the eye are defined by CIE Chart in Figure 7-1. The boundary of the colors the projector
can display is called the system color gamut. The white triangle in the figure is an example of a system color
gamut. By default the projector has the widest possible system gamut.

The system color gamut cannot be expanded outside native color gamut.

It may be desirable to change the system color gamut of the projector to:

• Color-match multiple projectors.

• Meet defined color standards, like REC 709.

• Create a special “look” to the image.

Before the system color gamut can be changed, the desired RealColor™ mode has to be defined. To
change the RealColor™ mode please go the menu PICTURE > REALCOLOR > DESIRED VALUES >
DESIRED COORDS MODE.

RealColor™ has to be enabled for the desired system gamut to be applied. Go to menu PICTURE > RE-
ALCOLOR > COLOR CORRECTION to enable RealColor™.

After RealColor™ is enabled and the desired color correction mode is selected, please go the menu entry
PICTURE > REALCOLOR > DESIRED VALUES to change the color points to your desired system color
gamut.

60

7.3 Gamma

The projector features a set of 6 built in gamma curves: Film 2.2, Film 2.4, Film 2.6, Film 2.8, Video 1,
Video 2, Computer 1, Computer 2, Dynamic and DICOM 180. The different gamma curves are displayed
below.

The names of the curves are descriptive for their recommended use. Using any of the computer
curves for video applications will results in significant image noise.

Figure 7-1. Film 2.2 gamma

Figure 7-2. Film 2.4 gamma

Figure 7-3. Film 2.6 gamma

61

Figure 7-4. Film 2.8 gamma

Figure 7-5. Video 1 gamma

Figure 7-6. Video 2 gamma

62

Figure 7-7. Computer 1 gamma

Figure 7-8. Computer 2 gamma

Figure 7-9. Dynamic gamma

63

Figure 7-10. DICOM 180 Lux* (example HB color wheel: other shapes with other alternatives)

* Several DICOM settings (10, 60, 180, 250, 400 Lux - The higher Lux number (ambient light), the steeper the curve.

64

65

8 Technical specifications

Visit www.barco.com for the latest specifications.

66

67

9 Lamp change

The lamp holder has an electronic lamp timer that tracks the life time of the lamp. The LED indicator on the key­pad will turn RED when the lamp life is expired. The lamp must be changed when the lifetime has expired. Failure
to do so increases the risk of malfunction.

Replacement lamps must be of the same type and rating. USE ORIGINAL LAMPS ONLY.

Always disconnect the power cord and wait until the projector has cooled down (at least 60 minutes) before
opening the lamp cover.

Do not touch the protective glass when replacing the lamp as

this may cause the protective glass to overheat and break while in use.

Take care when removing the lamp module. In the unlikely event of a bulb rupture, small glass fragments
may be generated. The lamp module is designed to contain these fragments, but use caution when
removing the lamp module.

To remove the expired lamp:

1. Unscrew the lamp door screw

2. Open the lamp door

3. Unscrew the three screws that hold the lamp in place

4. Pull the lamp out using the handle

Replace with a new lamp in reverse order:

1. Insert a new lamp. Observe the guide pins and make sure the lamp is fully inserted

2. Fasten the three screws securely

3. Close the lamp door

4. Tighten the lamp door screw firmly

In the unlikely event of a lamp rupture, a limited amount of mercury vapor may be emitted into the room.
To avoid inhaling this mercury vapor (which is toxic, and can be harmful for lungs and nervous system)
the room should be thoroughly ventilated for at least 30 minutes. There are no known health hazards
from exposure to lamps that are intact and which are used within an enclosed fixture. No adverse effects
are expected from occasional exposure to broken lamps. As a matter of good practice, avoid prolonged or
frequent exposure to lamps unless there is adequate ventilation. The major hazard from broken lamps is
the risk of sustaining glass cuts.

68

PRODUCTION ADDRESS

Habornveien 53

1630 Gamle Fredrikstad

Norway

Model certification name:

GP9

© 2014 Barco nv. All rights reserved. All brands and trade names are the property of their respective owners. Specifications subject to change without prior notice.

All values are typical and may vary. Please visit our website for latest specifications and product offerings.

601-0376-00