Barco MFCD 3220 D Installation & User Manual

Installation & User Manual

B410512 / 00

July 2004

MFCD 3220 D

 Read the safety and
operating instructions before
operating the apparatus.
 Retain safety and operating
instructions for future
reference.
 Adhere to all warnings on
the apparatus and in the
operating instructions
manual.
 Follow all instructions for
operation and use.

This apparatus conforms to:

CE, IEC 60950, UL 60950, CAN/
CSA C22.2 No. 60950 (cUL)

Power connection

 Warning: This apparatus
must be earthed!
 Power requirements: The
apparatus must be powered
using the 12 VDC power
supply that is supplied with
the apparatus.
The 12 VDC power supply
must be powered by the AC
mains voltage.
 Do not overload wall outlets
and extension cords as this
may result in fire or electric
shock.
 Mains lead protection:
Supply cords should be
routed so that they are not
likely to be walked upon or
pinched by items placed
upon or against them, paying
particular attention to cords
at plugs and receptacles.

SAFETY INSTRUCTIONS

Water and moisture

 Never expose the
apparatus to rain or
moisture.
 Never use the apparatus
near water - e.g. near a
bathtub, washbasin,
swimming pool, kitchen
sink, laundry tub or in a wet
basement.

Ventilation

 Do not cover or block the
ventilation openings in the
cover of the set. When
installing the apparatus in a
cupboard or another closed
location, heed the
necessary space between
the set and the sides of the
cupboard.

Installation

 Place the apparatus on a
flat, solid and stable surface
that can bear the weight of
at least 3 displays. If you
use an unstable cart or
stand, the set may fall,
causing serious injury to a
child or adult, and
seriousdamage to the
equipment.

MFCD 3220D User's Guide 4

MFCD 3220D User's Guide 5

CONTENTS

1. Overview ......................................................................................................... 7

1.1 Introduction .............................................................................................. 7

I-Guard ....................................................................................................... 7

1.2 Package contents .................................................................................... 8

1.3 Controls and connectors ......................................................................... 8

2. Installation .................................................................................................... 10

2.1 Precautions ............................................................................................ 10

2.2. Before installing the display ................................................................. 10

2.3 Portrait or landscape position ............................................................... 11

2.4 Connecting the signals ......................................................................... 12

To connect the power: ............................................................................. 12

To connect the video & sync signals: ...................................................... 12

2.5.Routing the signal cables ...................................................................... 13

2.7 Starting up .............................................................................................. 14

2.6 Tilt and swivel positioning ..................................................................... 14

3. Controls ........................................................................................................ 15

3.1 Stand-by switching ................................................................................. 15

3.2 Brightness control .................................................................................. 15

4. Maintenance ................................................................................................. 16

Panel ............................................................................................................ 16

Cabinet ......................................................................................................... 16

Removing dust from the rear of the glass panel ........................................ 16

6. Technical specifications ............................................................................... 17

MFCD 3220D User's Guide 6

MFCD 3220D User's Guide 7

1. OVERVIEW

1.1 Introduction

The MFCD 3220D, BARCOs 21 3 megapixel
color LCD display, guarantees perfect image
quality in medical imaging applications.

The display combines a TFT (thin film transistor)
liquid crystal display panel structure and a built-in
backlight with inverter for a better picture quality. It
is designed to meet the users' needs for
performance, consistency, and outstanding image
quality through a streamlined development
process.

The display can be used in portrait or landscape
version, simply by turning the panel. The tilt &
swivel foot allows ideal positioning of the panel, in
height and viewing angle.

The image brightness can be adjusted by means
of a control wheel on the display. Other image
parameters can be adjusted by means of external
software, like MediCal® Pro.

I-Guard

I-GUARD® is Barcos patent-pending, built-in
calibration device, continuously maintaining image
quality. With I-GUARD®, QA checks no longer
need to disturb normal radiology activities, as they
can be performed while applications are running.

I-GUARD® allows radiologists or QA
administrators to calibrate their viewing stations or
adjust the panels curve to DICOM standards
without administrator intervention.

MediCal Pro

In combination with Barcos MediCal ® Pro
management and calibration software package,
Coronis offers a truly intervention-free display
system, making it possible to perform QA checks
from one central server at any time, thereby
reducing lifecycle cost.

Multi-scan capabilities

The optimum and recommended resolution is
2048 x 1536 or 1536 x 2048 at 60 Hz.

The MFCD 3220D display will also display most
of the computer boot modes.

BARCO's BarcoMed 5MP2FH imaging board is
the best choice to drive the MFCD 3220D display.

MFCD 3220D User's Guide 8

1.2 Package contents

The package should include the following items,
please check. If some of the items are missing,
please contact the reseller you have purchased
the unit from.

- The MFCD 3220D display

- 12V DC power supply

- European power cord

- Dual-link DVI video cable

- This user manual

1.3 Controls and connectors

(4) (5) (6)

(1)

(2)
(3)

MFCD 3220D User's Guide 9

(1) Power LED

- The LED is off when the display is off.

- The LED is green when the display is on.
Note: This function can be switched off by
software.

- The LED is blinking green when the
display is in Suspend power-saving mode.

- The LED is orange when the display is in
Stand-by power-saving mode.

(2) Control wheel for stand-by switching and

luminance control

(3) USB-downstream connector

(4) USB-upstream connector

(5) DVI (video and data) input

(6) 12V DC power input

MFCD 3220D User's Guide 10

 Keep your original packaging. It is

designed for this display and is the ideal
protection during transport.

 Avoid reflections in the flat panel to reduce

eye strain.

 Place the display on a strong and stable

table or desk.

 Keep the display away from heat sources

and provide enough ventilation in case it is
built in a rack or console.

 Make sure the computer is switched off

before connecting the signals.

 Do not turn the power supply upside down

or at its side. Doing so would cause
overheating of the power supply.
Also do not block free air circulation around
the power supply.

2.2. Before installing the display

Important:

In the factory, the height-positioning system in
the display foot is blocked with a clip to prevent
damage during transportation.

Before installing the display, you must remove
this clip.

To remove the clip:

1 Position the display with its rear side facing

you.

2 If the foot cover is mounted on the foot, lift

up the 2 clips of the foot cover to release the
cover from the foot.

3 Pull the lower side of the cover towards you

and simultaneously slide the cover
downward.

2. INSTALLATION

2.1 Precautions

MFCD 3220D User's Guide 11

4 Pull the red clip out of the fixation holes in

the foot.

You can better leave the cover off the foot while
connecting the signal cables to the display.

2.3 Portrait or landscape position

You can change the orientation of the panel at
any time, but it is more convenient to select
landscape or portrait orientation before
connecting the cables.

To change the panel orientation:

1 Stand at the front side of the panel and take

the panel at both sides.

2 Very important: Tilt the panel before

changing the orientation.
Should you change the panel orientation
without tilting it first, you might irreversibly
damage the tilt & swivel mechanism.

3 To change from portrait to landscape, turn

the panel counterclockwise while lifting it
up slightly.
To change from landscape to portrait, turn
clockwise.

MFCD 3220D User's Guide 12

2.4 Connecting the signals

To get access to the connectors, open the cover
of the connector compartment by pulling down the
2 clips of the cover.

To connect the video & sync signals:

1 Connect one end of the video cable to the

DVI input (5) of the display.

2 Connect the other end of the video cable to

the video output of your video source
(Computer graphics board with digital video
output).

3 Route the cable so that it enters the

connector compartment at the place where
the cover is bulged.

Vid1

Vid2

Example of signal connection in a Coronis dual­head system

To connect the power:

1 Connect the output of the 12V DC power

supply to the DC input (6) of the display.

2 Connect one end of the proper power

cable to the AC input of the 12V DC power
supply.

MFCD 3220D User's Guide 13

2.5. Routing the signal cables

After connecting all cables, fix them in the cable
tie at the rear of the connector compartment. You
can also bind the cables together by means of the
2 velcro strips included in the package.

After fixing the cables, put the connector
compartment cover back in place. Pay attention
that the signal cables are positioned under the
bulge in the cover.

Next, fix the cables in the plastic clamps on the
foot. At last, put the foot cover back in place.

To put the foot cover in place:

1 Push the upper side of the cover onto the

foot, so that the hooks on the cover are
positioned right under the holes in the foot.

2 Slide the cover upward while moving the

lower side of the cover towards the foot.

3 Press the cover to the foot so that both clips

make a clicking sound.

3 Connect the other end of the power cord to

a grounded power outlet.

Push the upper side of the
cover onto the foot

Signal cables routed under foot
cover and bound by velcro strips

Connector
compartment

MFCD 3220D User's Guide 14

2.6 Tilt and swivel positioning

Adjust the position of the panel for best viewing
conditions.

The display foot allows adjusting the panel height,
horizontal viewing angle and vertical viewing
angle.

2.7 Starting up

Proceed as follows:

1 Switch on the computer.

2 If necessary, select a suitable resolution in

the computer operating system. You will
have to select a resolution that corresponds
to the panel orientation (landscape or
portrait).

Please refer to the possible resolutions in
the Technical specifications.

Note: The recommended resolution for best
image quality is 2048 x 1536 or 1536 x

2048.

MFCD 3220D User's Guide 15

The control wheel (2) at the bottom (portrait
orientation) or at the side (landscape orientation)
allows you to perform some controls. You can
switch the display in stand-by and control the
brightness.

3. CONTROLS

3.1 Stand-by switching

When the display is on, press the control wheel
slightly to switch the display in stand-by.

When the display is in stand-by, press the
control wheel slightly to turn it back on.

3.2 Brightness control

Turn the control wheel (2) clockwise to increase
the brightness.

Turn the control wheel (2) counterclockwise to
decrease the brightness.

The Brightness control can be disabled using the
MediCal Pro software.

(2)

MFCD 3220D User's Guide 16

4. MAINTENANCE

Panel

Take care not to damage or scratch the panel. Clean
with a soft woolen or cotton towel. Use a watery
solution or a mild commercial glass cleaning product.

Cabinet

Do not use chemical cleaning products, benzene,
toluene, xylene or other solvents. Clean with a soft
cloth dampened with mild detergent and water.
Repeat with water only and wipe dry with a dry cloth.

Removing dust from the rear of
the glass panel

It may be possible that dust particles have entered
the display and are stuck to the rear of the glass.

We recommend to let this cleaning procedure be
done in a BARCO service center.

However, when really necessary, you can perform the
cleaning on site if you can work in conditions that
are as clean and dust-free as possible. This is to
avoid more dust entering the display when opening it.

To remove the glass panel:

1 Switch off the display.

2 Tilt the panel.

3 Unscrew the 4 sunken screws at the rear, fixing

the glass panel and bezel.

4 Remove the bezel with glass panel.

Cleaning instructions:

- Dust, fingerprints, grease etc. can be removed by
using a soft damp cloth (a

small amount of mild

detergent can be used on the cloth, NOT solvent).

- Do not apply liquid directly to the LCD surface as
excess liquid may cause damage to internal
electronics.

- Take care not to touch the I-guard light sensor on
the LCD panel.

Tilt the panel

Remove the sunken screws

MFCD 3220D User's Guide 17

6. TECHNICAL SPECIFICATIONS

Picture panel

20.8-inch diagonal viewable screen TFT (thin film transistor) active matrix,
color liquid crystal display

Resolution

Native: 2048 x 1536

Display area (H x V)

423.7 x 318 (mm)

Viewing angle (@ 10:1 contrast)

Vertical: 170º
Horizontal: 170º

Input signals

Possible resolutions:

 640 x 350 @ 85 Hz
 720 x 400 @ 75 Hz
 1536 x 2048 @ 60 Hz

 2048 x 1536 @ 60 Hz
Video: Complying to DVI Rev 1.0 specifications
Sync: Complying to DVI Rev 1.0 specifications

Native color resolution

8 bits / sub-pixel

Signal system

DVI Digital (DVI-D)

Luminance

150 cd/m2 (calibrated)
180 cd/m² (maximum)

Contrast ratio

300:1 (in dark environment)

Response time

25 ms (@ 25° C after 30 min warmup)

Controls

Push / turn control wheel for stand-by switching and brightness control

Pixel Pitch

0.207 mm (H) x 0.207 mm (V)

MFCD 3220D User's Guide 18

Input connectors

DVI (DVI-D) dual channel

Power source

Input for 12 VDC power supply unit: 90 ~ 264 VAC
Input for display: 12 VDC. (The supplied 12VDC power supply must be used)

Power consumption

100 watts (max.)

Dimensions (W x H x D)

In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°:
385 x 590 x 240 mm

Net weight

13 kg

Operating Temperature

0°C to 40°C

Storage Temperature

-20°C to 60°C

NOTICE:
DUE TO OUR POLICY OF CONTINUOUS PRODUCT IMPROVEMENT, THE
ABOVE SPECIFICATIONS ARE SUBJECTED TO CHANGE WITHOUT
NOTICE. BARCO SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL
ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES WHATSOEVER RESULTING FROM
FURNISHING, PERFORMANCE OR USE OF THIS MATERIAL.