Barco JAO18, JAO15 User Manual

JAO15 / JAO18

User Guide

Smart Terminal for the patient bedside

K5903250/01
10/03/2016

Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
Phone: [phone]
Fax: [phone]
Support: www.barco.com/en/support
Visit us at the web: www.barco.com

PrintedinBelgium

Table of contents

TABLE OF CONTENTS

1. Introduction ........................................... ............................................ 3

1.1 Key features .... ................ ................ ................ ................ ................ ............... 3

1.2 What’s in the box.............................................................................................. 3

1.3 Product overview.............................................................................................. 4

2. Installation ........ ................................................................... .............. 7

2.1 Power connection............................................................................................. 7

2.2 SSD/HDD replacement....................................................................................... 7

2.3 RAM module replacement ...................... ................ ................ .................. ........... 8

2.4 JAOHandset installation..... ................ .................. ................ ................ ............... 9

2.5 VESA mounting ...............................................................................................10

3. Operation ................ .................................................................... ...... 13

3.1 On/Off switching.................. ................ ................ ................ ................ .............13

3.2 Service call ....................................................................................................13

3.3 USB charging..................................................................................................14

3.4 HDMI input...................... ................ ................ ................ ................ ............... 14

4. Cleaning ................................. ........................................................... 15

4.1 Cleaning instructions .........................................................................................15

5. Important information ....................................... .................................... 17

5.1 Safety information...................... .................. ................ ................ ................ .....17

5.2 Environmental information ...................................................................................19

5.3 Regulatory compliance information ............ ................ ................ ................ .............20

5.3.1 USA information.........................................................................................20

5.3.2 Canada information ................ ................ ................ ................ ................ .....21

5.4 EMC notice ... ................ ................ ................ ................ ................ ................ .22

5.5 Explanation of symbols.......... ................ .................. ................ ................ ...........25

5.6 Legal disclaimer...............................................................................................28

5.7 Technical specifications ......................................................................................28

K5903250 JAO15 / JAO18 10/03/2016

1

Table of contents

2 K5903250 JAO15 / JAO18 10/03/2016

1. Introduction

1. INTRODUCTION

1.1 Key features

Overview

JAO15 and JAO18 are designed to serve as a Point of Care (POC) and Point of Information terminals
(POI) within healthcare applications. Manufactured using anti-bacterial plastics, the terminals provide a
host of interactive healthcare applications providing secure access to Electronic Medical Records (EMR)
and innovative triple-play solutions (web, IPTV, VoIP) for patient entertainment.

• 16:9 15.6” (JAO15) or 18.5” (JAO18) 1366x768 Fanless LED Panel Computer

• Intel

• Flat Panel by Resistive (JAO15) or PCAP (JAO18) Touch Screen

• With 1x GbE/ HDMI input/ 5x USB ports

• Built in speaker/ microphone/ 2x line out

• 13.56MHz RFID/ Smart card reader

• DDR3L 2GB/ 2.5” 32GB SSD

• System Power Input 19V DC

®

Celeron®J1900, Quad Core, Low Consumption CPU

1.2 What’s in the box

Overview

• JAO15 or JAO18 terminal

• Power supply

• Power cords (EU and US type)

• Set of mounting screws (only compatible with Barco mounting solutions)

• Safety instructions sheet

K5903250 JAO15 / JAO18 10/03/2016

3

1. Introduction

1.3 Product overview

Front

1

Image 1-1

2

3

4

1. Camera
720p camera with white LED

2. Barcode scanner (optional on JAO18, not supported on JAO15)

3. Multipurpose, configurable power key
Please refer to the SDK documentation for more information about the different power key configura­tion options.

4. Combined SCR and RFID reader
Combo Smart Carder Reader (SCR) + High-frequency (13.56MHz) RFID reader, with RFID contact­less tapping and card parking support.

Back

1

2

3

9

3

8

6

7

4

Image 1-2

4

5

4 K5903250 JAO15 / JAO18 10/03/2016

1. Introduction

1. Microphone
Built-in digital microphone

2. SSD/HDD service door
Locked with Security Torx screws, used for SSD/HDD replacement.

3. JAOHandset side door (2x)
To be removed to install the JAOHandset (optional).

4. Speaker (2x)
Built in stereo speaker

5. Combined SCR and RFID reader
Combo Smart Carder Reader (SCR) + High-frequency (13.56MHz) RFID reader, with RFID contact­less tapping and card parking support.

6. Bottom IO area

Image 1-3

- 2 x headset line out jack

- 2 x USB 2.0 connector (5V / 1.5A)

- HDMI input connector

7. Barcode scanner (optional on JAO18, not supported on JAO15)

8. Rear IO area

SC19V

Image 1-4

- Functional earth blind fastener

- 19V DC power supply input connector

- 6P6C RJ11 service call (SC) connector

- 3 x USB 2.0 connector

- RJ45 LAN Gigabit Ethernet connector

9. RAM and miniPCIe service door
Locked with Security Torx screws, used for RAM replacement or installation of an extension module.

CAUTION: The service doors may only be opened by qualified service personnel, no

user serviceable parts inside.

WARNING: To prevent pos sible hearing damage, check the volume before using the

JAOHandset or headset line out and do not listen at high volume levels for long periods.

K5903250 JAO15 / JAO18 10/03/2016 5

1. Introduction

6 K5903250 JAO15 / JAO18 10/03/2016

2. Installation

2. INSTALLATION

2.1 Power connection

Overview

1. Connect the supplied external DC power supply to the +19 VDC power input of your JAO15 / JAO18.

2. Plug the other end of the external DC power supply into a grounded power outlet by means of the proper

power cord delivered in the packaging.

3. Optionally, earth the terminal by connecting the functional earth blind fastener to a grounded outlet by

means of a wire with at minimum AWG18 size (according to national Regulation requirements regarding
maximum admitted cable length). Use an M3 screw to attach the wire to the functional earth blind
fastener.

Image 2-1

WARNING: When you unplug the power cable, always pull the plug, never pull the cable.

Although the JAO15 and JAO18 have a very low standby power consumption, unplug
the power cable to save e nergy if you do not use the terminal for a long period of time.

Connector type: 5.5 mm DC jack

2.2 SSD/HDD replacement

CAUTION: Prior to removing any service door, make sure the unit’s power is off and

disconnected from the power sources to prevent electric shock or system damage.

To fully disengage the power to the unit, please disconnect the power cord from the AC
inlet.

To replace the SSD/HDD

1. Unscrew the Security Torx screws of the SSD/HDD service door, then remove the door.

K5903250 JAO15 / JAO18 10/03/2016

7

2. Installation

Image 2-2

2. Remove the current SSD/HDD and replace it with a new one.

Image 2-3

3. Put the SSD/HDD service door back in place and fix it with the Security Torx screws.

2.3 RAM mo du le replacement

CAUTION: Prior to removing any service door, make sure the unit’s power is off and

disconnected from the power sources t

To fully disengage the power to the unit, please disconnect the power cord from the AC
inlet.

To replace the RAM module

1. Unscrew the Security Torx screws of the RAM service door, then remove the door.

o prevent electric shock or system damage.

Image 2-4

8 K5903250 JAO15 / JAO18 10/03/2016

2. Remove the current DDR3L RAM module and replace it with a new one.

Image 2-5

3. Put the RAM service door back in place and fix it with the Security Torx screws.

2.4 JAOHandset installation

2. Installation

CAUTION: Prior to removing any service door, make sure the unit’s power is off and

disconnected from the power sources to prevent electric shock or system damage.

To fully disengage the power to the unit, please disconnect the power cord from the AC
inlet.

WARNING: To prevent possible hearing damage, check the volume

JAOHandset and do not listen at high volume levels for long periods.

before listening the

To switch the position of the JAOHandset (L/R)

The default mounting position of your JAOHandset is on the left hand side of your terminal. The procedure
below describes how to prepare the JAOHandset for right hand side mounting.

1. Remove the 2 caps and the screws at the inside of the handset cradle.

2. Take apart the mounting bracket from the handset cradle and rotate the bracket 180°.

3. Reassemble the handset cradle with the 2 fixation screws and reinsert the screw caps.

Image 2-6

The JAOHandset can now be attached to your terminal as described in the next procedure.

K5903250 JAO15 / JAO18 10/03/2016

9

2. Installation

To install the JAOHandset

1. Remove the handset side door.

Image 2-7

2. Connect the handset connector to the cable available behind the side door. Please make sure to con-

nect the white dot to white dot pin.

Image 2-8

3. Use the screws from the handset box to firmly attach the handset to your terminal.

Image 2-9

2.5 VESA mounting

To mount the JAO15 / JA

Your JAO15 and JAO18 is compatible with the VESA 75 mm and VESA 100 mm standard, so it can be
used on different VESA 75 and VESA 100 mounting solutions (arms, desk stands, ...).

O18 on a VESA solution

10

K5903250 JAO15 / JAO18 10/03/2016

2. Installation

Image 2-10

The VESA mounting holes at the back of the terminal are provided with M4-type blind fasteners to fixthe
VESA mounting plate. Depending on the VESA plate thickness (T) and the thickness of possible washers
(W), a different screw length (L) should be selected.

Please respect the following rule to select an appropriate screw length:

•L

min

•L

max

Image 2-11

=T+W+4mm

=T+W+5.5mm

T

W

L

min

Lmax

CAUTION: Use only a mounting solution that is in compliance with VESA requirements.

WARNING: The mounting screws included in the box of your JAO15 / JAO18 are only to

be used with Barco mounting s ol

K5903250 JAO15 / JAO18 10/03/2016 11

utions.

2. Installation

12 K5903250 JAO15 / JAO18 10/03/2016

3. Operation

3. OPERATION

3.1 On/Off switching

Overview

The way to switch your terminal on or off depends on the BIOS settings, configurable in the SDK. Please
refer to the SDK documentation for more information about the different on/off switching configuration
options.

3.2 Service call

Overview

The optional service call button and status LED of the JAOHandset are internally wired to the RJ11 Service
Call connector which can be connected to the hospital’s internal network service call system.

The electrical signal of the service call button in the JAOHandset and the status LED of the JAOHandset
can be detected/controlled on the RJ11 Service Call connector of your JAO15 / JAO18. Please refer to the
connector pinout below for more details. The electrical signal requirements are available in the technical
specification tables of this user guide (see "Technical specifications", page 28).

WARNING: The RJ11 connector may not be connected to a telephony or telecom net-

work and is for use only with the hospital’s internal network service call system

The service call button is optional and not present on all JAOHandset models.

RJ11 Service Call connector pinout

Please use a 6P6C RJ11 connector with below pinout only.

Image 3-1

1. Not connected

2. Button +

3. Button -

4. LED +

5. LED -

6. Not connected

K5903250 JAO15 / JAO18 10/03/2016

13

3. Operation

3.3 USB charging

Overview

The bottom USB ports on the JAO15 and JAO18 are capable of delivering 5V/1.5A output. This means
you will be able to charge almost any smartphone, camera, ebook reader, etc. by plugging them into the
terminal bottom USB ports.

USB charging is not possible via the USB ports at the back of your terminal.

3.4 HDMI input

Overview

The JAO15 and JAO18 are capable of playing High Definition video and audio of any HDMI compatible
device (gaming console, DVD player, camera, etc.) that is connected to the HDMI input of your terminal.

For best signal quality transfer, use a High speed HDMI cable and do not use an HDMI
cable longer than 5 m.

14 K5903250 JAO15 / JAO18 10/03/2016

4. Cleaning

4. CLEANING

4.1 Cleaning instructions

To clean your JAO15 and JAO18

Clean the terminal using a sponge, cleaning cloth or soft tissue, lightly moistened with a recognized clean­ing product for medical equipment. Read and follow all label instructions on the cleaning product. In case
of doubt about a certain cleaning product, use plain water.

Do not use following products:

• Alcohol/solvents at higher concentration > 5%

• Strong alkalis lye, strong solvents

•Acid

• Detergents with fluoride

• Detergents with ammonia

• Detergents with abrasives

• Steel wool

• Sponge with abrasives

• Steel blades

• Cloth with steel thread

CAUTION: Take care not to damage or scratch the front glass or LCD. Be careful with

rings or other jewelry and do not apply excessive pressure on the front glass or LCD.

CAUTION: Do not apply or spray liquid directly to the ter minal as excess liquid may

cause damage to internal electronics which may cause fire or electrical shock. Instead,
apply the liquid to a cleaning cloth.

In environments where specific chemicals or cleaning agents are used, please contact
your local Barco office.

K5903250 JAO15 / JAO18 10/03/2016 15

4. Cleaning

16 K5903250 JAO15 / JAO18 10/03/2016

5. Important information

5. IMPORTANT INFORMATION

5.1 Safety information

General recommendations

• Read the safety and operating instructions before operating the equipment.

• Retain safety and operating instructions for future reference.

• Adhere to all cautions, warnings and instructions on the equipment, safety instructions and user gu
Detailed product information and the user guide are available for download from the Barco website.
Please go to w

Electrical Shock or Fire Hazard

• To prevent electric shock or fire hazard, do not open the equipment or remove any covers.

• No serviceable parts inside. Refer servicing to qualified personnel.

• Do not expose this equipment to rain or moisture.

ww.barco.com.

ide.

Modifications to the equipment

Do not modify this equipment without authorization of the manufacturer.

Service

If one of the following situations arises, ensure you get the equipment checked by service personnel:

• The power cord or plug is damaged.

• The equipment has been exposed to moisture.

• The equipment is not functioning properly, or you cannot get it to work according to the user guide.

• The equipment has been dropped and damaged.

• The equipment has obvious signs of breakage.

Installation & mounting

• When installing the equipment in a cupboard or another closed location, heed the necessary space
between the set and the sides of the cupboard.

• Place the equipment on a stable surface that can support the weight of at least 4 terminals or hang
from a reliable structure during installation. Dropping the equipment is likely to cause serious injury to
a child or adult, and serious damage to the equipment.

• Improper installation of VESA mounting can result in serious personal injury! Use a VESA mounting
solution that can support a weight of at least 10kg. VESA mount installation should be carried out by a
professional technician. Please contact the service technician or your reseller if you need this service.

Type of protection ( electrical):

Equipment with external power supply: Class II equipment.

Degree of safety (flammable anesthetic mixture):

Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen
or nitrous oxide.

Non-patient care equipment

• This equipment is not intended to be used in life support systems, operating rooms or for diagnostic
purposes.

• The user is not supposed to touch SIP/SOPs and the patient at the same time.

K5903250 JAO15 / JAO18 10/03/2016

17

5. Important information

Power connection – Equipment with external 19 VDC power supply

• Power requirements: The equipment must be powered using the delivered medical approved 19 VDC
(

) power supply. Model: DELTA MDS-090AAS19 B.

• The medical approved DC (

1.5-0.75A 50-60Hz).

• The power supply is specified as a part of the ME equipment or combination is specified as a ME
system.

• Make sure the voltage of the power source is correct before connecting the equipment to the power
outlet.

• The equipment should be installed near an easily accessible outlet.

• The equipment is intended for continuous operation.

Transient over-voltage

• If the equipment is not used for a long time, disconnect it from the AC inlet to avoid damage by transient
over-voltage.

• To fully disengage the power from the equipment, please disconnect the power cord from the AC inlet.

Power cords

• Do not overload wall outlets and extension cords as this may result in fire or electric shock.

• Power cords should be routed so that they are not likely to be walked upon or pinched by items placed
upon or against them, paying particular attention to cords at plugs and receptacles.

• Use a power cord that matches the voltage of the power outlet, which has been approved and complies
with the safety standard of your particular country.

) power supply must be powered by the AC mains voltage (100-240V~

Grounding

Optionally earth the equipment by connecting the functional earth blind fastener to a grounded outlet by
means of a wire with at minimum AWG18 size (according to national Regulation requirements regarding
maximum admitted cable length).

Water and moistu re

• Keep this equipment away from excessive humidity.

• Never use the equipment near water - e.g. near a bathtub, washbasi
laundrytuborinawetbasement.

n, swimming pool, kitchen sink,

Cleaning

• The equipment can be cleaned regularly according to usage. In e
cals or cleaning agents are used, please contact your local Barco office.

• Do not apply or spray liquid directly to the equipment as excess liquid may cause damage to internal
electronics which may cause fire or electrical shock. Instead, apply the liquid to a cleaning cloth.

nvironments where specificchemi-

External equipment

• The RJ11 connector may not be connected to a telephony or telecom network and is for use only with
the hospital’s internal network service call system.

• If the equipment is equipped with a handset, the handset can magnetically retain small sharp objects
(such as pins & paperclips) around the mouthcap or earcap region, please check and remove before
use.

• Accessory equipment connected to the analog and digital interfaces must be in compliance with the
respective nationally harmonized IEC standards (i.e. IEC 60601 for data processing equipment). If in
doubt, consult the technical services department or your local representative.

18

K5903250 JAO15 / JAO18 10/03/2016

5. Important information

• External connections to model JAO15 / JAO18 (I/O, LAN, etc) shall be in compliance with the require­ments for medical electrical systems as stated in chapter 16 of the standard for medical electrical
equipment IEC 60601-1.

Batteries

• If your equipment is losing time or the BIOS configuration resets to default settings, the battery most
likely has no power.

• Do not replace the battery yourself. Please contact a qualified technician or your supplier of the JAO15
/ JAO18. There is a danger of leakage or explosion if the battery is incorrectly replaced. The JAO15
/ JAO18 is provided with a battery-powered real-time clock circuit.

Laser radiation

WARNING: Use of controls or adjustments or performance of proced

those specified herein may result in hazardous radiation exposure.

ures other than

Recycling

For more information about recycling of this equipment, please contact your local city office, your municipal
waste disposal service or the shop where you purchased the equipment.

Storage

Do not leave this equipment in an uncontrolled environment where the storage temperature is below -20
°C or above 60°C. This may damage the equipment.

This apparatus conforms to

JAO15 / JAO18 (without
JAOHandset)

- ANSI/AAMI ES 60601-1

- CAN/CSA-C22.2 No.60601-1

-FCCclassB

- CAN ICES-3 (B)/NMB-3(B)

-CE

JAO15 / JAO18 (with JAOHandset)

- IEC 60950-1:2005 (Second Edition) + Am 1:2009 + Am 2:2013

- EN 60950-1:2006 /A11:2009/A1:2010/ A12:2011/ A2:2013 and
AS/NZS 60950.1:2015

-FCCclassB

- CAN ICES-3 (B)/NMB-3(B)

-CE

5.2 Environmental information

Disposal Information

Waste Electrical and Electronic Equipment

K5903250 JAO15 / JAO18 10/03/2016

19

5. Important information

This symbol on the product indicates that, under the European Directive 2012/19/EU governing
waste from electrical and electronic equipment, this product must not be disposed of with other municipal
waste. Please dispose of your waste equipment by handing it over to a designated collection point for the
recycling of waste electrical and electronic equipment. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate these items from other types of waste
and recycle them responsibly to promote the sustainable reuse of material resources.

For more information about recycling of this product, please contact your local city office or your municipal
waste disposal service.

For details, please visit the Barco website at: h

ttp://www.barco.com/en/AboutBarco/weee

Disposal of batteries in the product

This product contains batteries covered by the Directive 2006/66/EC which must be collected and

disposed of separately from municipal waste.
If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these

chemical symbols will appear below the crossed-out wheeled bin symbol.
By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent

potential negative effects on the environment and human health.

Turkey RoHS compliance

Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur.

[Republic of Turkey: In conformity with the WEEE Regulation]

5.3 Regulatory compliance information

5.3.1 USA information

Indications for use

The JAO15 and JAO18 are intended to be used at the patient bedside, for the purpose of patient enter­tainment, patient information, patient communication (phone and video phone), patient administration and
service calls.

The JAO15 and JAO18 additionally allo
users.

The JAO15 and JAO18 is not intended to be used in patient monitoring, diagnosis, treatment, alleviation
or prevention of diseases, injuries and handicaps.

w for remote access to hospital systems by trained professional

RF exposure warning

This equipment must be installed and operated in accordance with provided instructions and the an­tenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm
from all persons and must not be co­mitter. End-users and installers must be provided with antenna installation instructions and transmitter
operating conditions for satisfying RF exposure compliance.

20

located or operating in conjunction with any other antenna or trans-

K5903250 JAO15 / JAO18 10/03/2016

5. Important information

FCC class B

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference re­ceived, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This device generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interfe
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television reception, which can be
determined by turning the device off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the device and receiver.

• Connect the device into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

rence

5.3.2 Canada information

Industry Canada (IC) notices

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, an
interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna

or transmitter, except tested built-in radios.
The County Code Selection feature is disabled for products marketed in the US/ Canada.

d (2) this device must accept any

Avis d’lndustry Canada (IC)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une autre

antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées.
La fonction de sélection de l’indicatif du pays est désactivée pour les produits commercialisés aux États-

Unis et au Canada.

Radiation exposure statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated wi
body.

th minimum distance 20cm between the radiator & your

Déclaration d’exposition aux radiations

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environ­nement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance
entre la source de rayonnement et votre corps.

K5903250 JAO15 / JAO18 10/03/2016

21

5. Important information

5.4 EMC notice

When the JAO15 / JAO18 is used in combination with external peripherals, including
the JAOHandset, the test levels which are listed further below are not applicable and
the EN55022 (CISPR22) and EN55024 (CISPR24) test levels apply instead.

General information

No specific requirement on the use of external cables or other accessories except power supply.
With the installation of the device, use only the delivered power supply or a spare part provided by the

legal manufacturer. Using another can result in a decrease of the immunity level of the device.

Electromagnetic emissions

The JAO15 / JAO18 is intended for use in the electromagnetic environment specified below. The customer
or the user of the JAO15 / JAO18 should assure that it is used in such an environment.

Emissions test

RF emissions
CISPR 11

RF emissions
CISPR 11

Harmonic emissions
IEC 61000-3-2

Voltage fluctuations/ flicker
emissions

IEC 61000-3-3

This JAO15 / JAO18 complies with appropriate medical EMC standards on emissions to, and interference
from surrounding equipment. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interfer­ence that may cause undesired operation.

Interference can be determined by turning the equipment off and on.
If this equipment does cause harmful interference to, or suffer from harmful interference of, surrounding

equipment, the user is encouraged to try to correct the interference by one or more of the following mea­sures:

Compliance

Group 1 The JAO15 / JAO18 uses RF

Class B

Class D

Complies

Electromagnetic environment –
Guidance

energy only for its internal function.
Therefore, its RF emissions are
very low and are not likely to
cause any interference in nearby
electronic equipment.
The JAO15 / JAO18 is suitable
for use in all establishments,
including domestic establishments
and those directly connected to
the public low-voltage power
supply network that supplies
buildings used for domestic
purposes.

• Reorient or relocate the receiving antenna or equipment.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced technician for help.

Electromagnetic immunity

The JAO15 / JAO18 is intended for use in the electromagnetic environment specified below. The customer
or the user of the JAO15 / JAO18 should assure that it is used in such an environment.

22

K5903250 JAO15 / JAO18 10/03/2016

5. Important information

Immunity test

Electrostatic discharge
(ESD)

IEC 61000-4-2

Electrical fast
transient/burst

IEC 61000-4-4

Surge
IEC61000-4-5

Voltage dips, short
interruptions and voltage
variations on power
supply input lines

IEC 61000-4-11

Power frequency (50/60
Hz) magnetic field

IEC 61000-4-8

Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3

IEC 60601

Test levels

± 6kV contact
±8kVair

± 2kV for power supply
lines

± 1kV for input/ output
lines

± 1 kV line(s) to line(s)
± 2 kV line(s) to earth

<5%U
U

T

40% U

1

(> 95% dip in

T

) for 0.5 cycle

(60%dipinUT)

T

for 5 cycles
70% U

(30%dipinUT)

T

for 25 cycles
<5%U

U

) for 5s

T

(>95% dip in

T

3A/m

3Vrms
150 kHz to 80 MHz
3V/m
80 MHz to 2.5 GHz

Compliance level

± 6kV contact
±8kVair

± 2kV for power supply
lines

± 1kV for input/ output
lines

± 1 kV line(s) to line(s)
±2kVline(s)toearth

<5%U
U

) for 0.5 cycle

T

40% U

(> 95% dip in

T

(60% dip in UT)

T

for 5 cycles
70% U

(30% dip in UT)

T

for 25 cycles
<5%U

U

)for5s

T

Not applicable

(>95% dip in

T

2

3V

3V/m

Electromagnetic
environment –
guidance

Floors should be wood,
concrete or ceramic tile.
If floors are covered with
synthetic material, the
relative humidity should
be at least 30%

Mains power quality
should be that of a typical
commercial or hospital
environment

Mains power quality
should be that of a typical
commercial or hospital
environment

Mains power quality
should by that of a typical
commercial or hospital
environment. If the user
of the JAO15 / JAO18
requires continued
operation during power
mains interruptions, it
is recommended that
the JAO15 / JAO18
be powered from an
uninterruptible power
supply or a battery.
Power frequency
magnetic fields should
be at levels characteristic
of a typical location in
a typical commercial or
hospital environment.
Portable and mobile
RF communications
equipment should be
used no closer to any
part of the JAO15 /
JAO18, including cables,
than the recommended
separation distance
calculated from the
equation applicable
to the frequency
of the transmitter.
Recommended
separation distance

d=1.2√P
d=1.2√P 80 MHz to 800

MHz
d=2.3√P 800 MHz to 2.5

Ghz

1. is the a.c. mains voltage prior to application of the test level.

2. JAO15 / JAO18 doesn’t contain susceptible components to magnetic fields

K5903250 JAO15 / JAO18 10/03/2016 23

5. Important information

Immunity test

IEC 60601

Test levels

Compliance level

Electromagnetic
environment –
guidance

Where P is the maximum
output power rating
of the transmitter in
watts (W) according
to the transmitter
manufacturer and d
is the recommended
separation distance in
meters (m).

Field strengths from
fixed RF transmitters,
as determined by an
electromagnetic site
survey,

3

should be less
than the compliance
level in each frequency

4

range.
Interference may occur in

the vicinity of equipment
marked with symbol:

At 80 MHz and 800 MHz, the higher frequency range applies.

These guidelines may not apply in all situations. Electromagnetic propagation is af­fected by absorption and refle ction from structures, obje cts and people.

Recommended separation distance

The JAO15 / JAO18 is intended for use in an electromagnetic environment in which radiated RF distur­bances are controlled. The customer of the user of the JAO15 / JAO18 can help prevent electromagnetic
interference by maintaining a minimum distance between portable and mobile RF communications equip­ment (transmitters) and the JAO15 / JAO18 as recommended below, according to the maximum output
power of the communications equipment.

3. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur
radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the
location in which the JAO15 / JAO18 is used exceeds the applicable RF compliance level above, the JAO15 / JAO18 should be observed
to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or
relocating the JAO15 / JAO18.

4. Over the frequency range 150 kHz to 80 MHz, field strengths should be less than3V/m.

24 K5903250 JAO15 / JAO18 10/03/2016

5. Important information

Rated maximum output
power of transmitter

W

0.01 0.12 0.12 0.23

0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8 7.3
100121223

At 80 MHz and 800 MHz, the s eparation distance for the higher frequency range applies.

These guidelines may not apply in all situations. Electromagnetic propagation is af­fected by absorption and reflection form structures, object and people.

Separation distance according to frequency of transmitter

5

150kHz to 80MHz
d=1.2√P

80MHz to 800MHz
d=1.2√P

800MHz to 2.5GHz
d=2.3√P

5.5 Exp lanation of symbols

Symbols on the device

On the device or power supply, you may find the following symbols (nonrestrictive list):

Indicates the device meets the requirements of the applicable EC directives.

Indicates compliance with Part 15 of the FCC rules (Cla

Indicates the device is approved according to the UL R

Indicates the device is approved according to the UL regulations for Canada
and US

Indicates the device is approved according to the UL Demko regulations

Indicates the device is approved according to the CCC regulations

ss A or Class B)

ecognition regulations

Indicates the device is approved according to the VCCI regulations

5. For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be
estimated using the equation applicable to the frequency of the transmitter. Where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter manufacturer.

K5903250 JAO15 / JAO18 10/03/2016 25

5. Important information

Indicates the device is approved according to the KC regulations

Indicates the device is approved according to the BSMI regulations

Indicates the device is approved according to the PSE regulations

Indicates the USB connectors on the device

Indicates the DisplayPort connectors on the device

Indicates the legal manufacturer

Indicates the manufacturing date

Indicates the temperature limitations6for the device to safely operate within specs.

Indicates the device serial number

Indicates the device part number or catalogue number

Warning: dangerous voltage

Caution

Consult the operating instructions

Indicates this device must not be thrown in the trash but must be recycled,
according to the Eur
directive

6. Values for xx and yy can be found in the technical specifications paragraph.

26 K5903250 JAO15 / JAO18 10/03/2016

opean WEEE (Waste Electrical and Electronic Equipment)

SC

5. Important information

Indicates Direct Current (DC)

Indicates Alternating Current (AC)

Stand-by

Equipotentiality

Functional earth (ground)

Indicates the position of the RFID and smart card reader.

Indicates the position of the Service Call connector.

Indicates the position of the headset line out jack(s).

Indicates the position of the LAN Gigabit Ethernet connector.

Symbols on the box

On the box of the device, you may find the following symbols (nonrestrictive list):

Indicates a device that can be broken or damaged if not handled carefully when
being stored.

Indicates a device that needs to be protected from moisture when being stored.

Indicates the storage direction of the box. The box must be transported, handled
and stored in such a way that the arrows always point upwards.

15

n

20 - 30 Kg

n

or

Indicates the maximum number of identical boxes which may be stacked on each
other, where “n” is the limiting number.

Indicates that the box should be carried with two persons.

Indicates that the box should not be cut with a knife, a cutter or any other sharp
object.

yy

xx

-20 °C

+60 °C

being stored.

K5903250 JAO15 / JAO18 10/03/2016 27

Indicates the temperature limits7to which the device can be safely exposed when

5. Important information

yy

85 %

Indicates the range7of humidity to which the device can be safely exposed when
being stored.

x

5 %

yyy

106 kPa

Indicates the range7of atmospheric pressure to which the device can be safely
exposed when being stored.

xx

50 kPa

5.6 Legal disclaimer

Disclaimer notice

Although every attempt has been made to achieve technical accuracy in this document, we assume no
responsibility for errors that may be found. Our goal is to provide you with the most accurate and usable
documentation possible; if you discover errors, please let us know.

Barco software products are the property of Barco. They are distributed under copyright by Barco NV or
Barco Inc., for use only under the specific terms of a software licen
Barco Inc. and the licensee. No other use, duplication, or disclosure of a Barco software product, in any
form, is authorized.

The specifications of Barco products are subject to change without notice.

se agreement between Barco NV or

Trademarks

All trademarks and registered trademarks are property of their respective owners.

Copyright notice

This document is copyrighted. All rights are reserved. Neither this document, nor any part of it, may
be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including
photocopying, taping or information storage and retrieval systems - without written permission of Barco.

© 2016 Barco NV all rights reserved.

5.7 Technical specifications

JAO15

Service call Optional, on JAOHandset

Handset

USB TV tuner module ATSC or DVB TV tuner USB dongle (for installation in the wallbox)

Bluetooth

JAOHandset with phone, hook switch and key membrane and optional
remote control buttons, Service call function, 2D barcode scanner

(Comes with cradle, left or right side mounting)
Optional, external accessory

Optional, external accessory
Combo WiFi 802.11b/g/n + Bluetooth Mini PCIe module
Optionally available from Custom Configuration Program, integrated

WiFi

Combo WiFi 802.11b/g/n + Bluetooth Mini PCIe module
Optionally available from Custom Configuration Program, integrated

7. Values for xx and yy can be found in the technical specifications paragraph.

28 K5903250 JAO15 / JAO18 10/03/2016

5. Important information

Barcode scanner

Combined SCR and RFID
reader

Display 15.6" WXGA (1366 x 768), Wide-screen (aspect ratio 16:9)

Warranty 24-months standard warranty

Power

Dimensions 418 x 270 x 50 mm

Color Barco White cover, Black bezel front glass
Certifications CE, FCC class B, EN 60601-1, UL 60601-1, IEC60950-1 CB

Weight 4.2 kg
Audio Integrated stereo speakers, 2 x 2 Watt, down-firing

N/A
Combo Smart Carder Reader (SCR) + High-frequency RFID reader,

with RFID contactless tapping and card parking support
Standard, integrated

Large viewing angle (160°/160° hor/ver typ)
Long lifetime (50,000 hrs MTBF)

Up to 5-years extended warranty contracts available
19V DC input, 4.74A current rating, medical wide AC-input power

supply
EU + US power cord standard

VESA mount, 75x75 and 100x100 compatible

ANSI/AAMI ES60601-1, CAN/CSA-C22.2 No.60601-1

Internal digital microphone

Backlight

CPU Intel® Celeron® Processor J1900 System-on-Chip (SoC)

Medical environment
considerations

BIOS AMI BIOS, 8M-bit SPI ROM

Storage capacity 2.5" Storage bay

Graphics chip set Integrated Intel® HD Graphics (Gen7)

Operating system Linux: Ubuntu 14.04.1 LTS and equivalent

LED, High luminance (300 cd/m2 typ)
Backlight brightness (+ on/off) controllable by software (GPIO)

2.0 GHz Quad-core with Burst up to 2.42 GHz
Antibacterial material (plastic housing)
Fanless design with passive cooling concept, no vents, no moving parts
IP65 front face

DMI information with unique identifier information

Standard 32 GB SSD installed

Hardware-accelerated video decoding support with Intel® Quick Sync
Video

Windows®: 7, 8 & 10

K5903250 JAO15 / JAO18 10/03/2016 29

5. Important information

Connectivity Gigabit Ethernet LAN, RJ45 (x1, on rear)

USB 2.0 (x2 on bottom, x3 on rear)
Headphone connector, 3.5mm mini jack (x2)
Handset connector (x2, internal left or right), compatible with optional

JAOHandset
HDMI input (x1, on bottom), 720p HD Ready resolution
Use as stand-alone screen to connect external source such as a

gaming console
Service Call connector for use with SC button on optional JAOHandset,

RJ11 (x1, on rear) - Input rating: +12V to +48V @ max. 20mA
Programmable GPIO (for Backlight control, Multipurpose buttons on

the front, Audio, …)

User interface Single-touch screen, 5-wire resistive touch technology

Note: Capacitive multi-touch optional, available from OEM
program

Multi-purpose capacitive touch keys in glass front-bezel
Standard On/Off switch, extra buttons available from Custom

Configuration Program

Webcam
System memory 1 slot DDR3L 1333 SO-DIMM socket, Support up to 8GB capacity

Integrated HD Camera (720p), with privacy LED indicator

Standard 2 GB installed

Storage pressure 50kPato106kPA
Operating temperature 0°Cto40°C
Storage temperature -20°C to 60°C
Operating humidity 20% to 80% (non-condensing)
Storage humidity 20% to 80% (non-condensing)

Operating pressure
Operating altitude Up to 3000m

50kPato106kPA

JAO18

Service call Optional, on JAOHandset
Handset JAOHandset with phone, hook switch and key membrane and optional

remote control buttons, Service call function, 2D barcode scanner
(Comes with cradle, left or right side mounting)
Optional, external accessory

USB TV tuner module ATSC or DVB TV tuner USB dongle (for installation in the wallbox)

Optional, external accessory

Bluetooth

WiFi

Combo WiFi 802.11b/g/n + Bluetooth Mini PCIe module
Optionally available from Custom Configuration Program, inte
Combo WiFi 802.11b/g/n + Bluetooth Mini PCIe module

grated

Optionally available from Custom Configuration Program, integrated

Barcode scanner 2D Barcode scanner

Optionally available from Custom Configuration Program, integr

30 K5903250 JAO15 / JAO18 10/03/2016

ated

5. Important information

Combined SCR and RFID
reader

Display

Warranty 24-months standard warranty

Power

Dimensions 482 x 309 x 48 mm

Color Barco White cover, Black bezel front glass
Certifications CE, FCC class B, EN 60601-1, UL 60601-1, IEC60950-1 CB

Weight 4.8 kg

Audio

Combo Smart Carder Reader (SCR) + High-frequency RFID reader,
with RFID contactless tapping and card parking support

Standard, integrated

18.5" WXGA (1366 x 768), Wide-screen (aspect ratio 16:9)
Large viewing angle (170°/160° hor/ver typical)
Long life-time (50,000 hrs MTBF)

Up to 5-years extended warranty contracts available
19V DC input, 4.74A current rating, medical wide AC-input power

supply
EU + US power cord standard

VESA mount, 75x75 and 100x100 compatible

ANSI/AAMI ES60601-1, CAN/CSA-C22.2 No.60601-1

Integrated stereo speakers, 2 x 2 Watt, down-firing
Internal digital microphone

Backlight

CPU Intel® Celeron® Processor J1900 System-on-Chip (SoC)

Medical environment
considerations

BIOS AMI BIOS, 8M-bit SPI ROM

Storage capacity 2.5" Storage bay

Graphics chip set Integrated Intel® HD Graphics (Gen7)

Operating system Linux: Ubuntu 14.04.1 LTS and equivalent

LED, High luminance (300 cd/m2 typical)
Backlight brightness (+ on/off) controllable by software (GPIO)

2.0 GHz Quad-core with Burst up to 2.42 GHz
Antibacterial material (plastic housing)
Fanless design with passive cooling concept, no vents, no moving parts
IP65 front face

DMI information with unique identifier information

Standard 32 GB SSD installed

Hardware-accelerated video decoding support with Intel® Quick Sync
Video

Windows®: 7, 8 & 10

K5903250 JAO15 / JAO18 10/03/2016 31

5. Important information

Connectivity Gigabit Ethernet LAN, RJ45 (x1, on rear)

USB 2.0 (x2 on bottom, x3 on rear)
Headphone connector, 3.5mm mini jack (x2)
Handset connector (x2, internal left or right), compatible with optional

JAOHandset
HDMI input (x1, on bottom), 720p HD Ready resolution
Use as stand-alone screen to connect external source such as a

gaming console
Service Call connector for use with SC button on optional JAOHandset,

RJ11 (x1, on rear) - Input rating: +12V to +48V @ max. 20mA
Programmable GPIO (for Backlight control, Multipurpose buttons on

the front, Audio, …)

User interface Capacitive 10-point Multi-touch screen, P-CAP touch technology

Note: Resistive single-touch optional, available from OEM
program

Multi-purpose capacitive touch keys in glass front-bezel
Standard On/Off switch, extra buttons available from Custom

Configuration Program

Webcam
System memory 1 slot DDR3L 1333 SO-DIMM socket, Support up to 8GB capacity

Integrated HD Camera (720p), with privacy LED indicator

Standard 2 GB installed

Storage pressure 50kPato106kPA
Operating temperature 0°Cto40°C
Storage temperature -20°C to 60°C
Operating humidity 20% to 80% (non-condensing)
Storage humidity 20% to 80% (non-condensing)

Operating pressure
Operating altitude Up to 3000m

50kPato106kPA

32 K5903250 JAO15 / JAO18 10/03/2016

Dimension drawing JAO15

5. Important information

267.0 ± 0.1 mm

269.7 ± 0.1 mm

Image 5-1

418.0 ± 0.1 mm

59.2 ± 0.1 mm294.7 ± 0.1 mm 64.1 ± 0.1 mm

50.0 ± 0.1 mm

32.1 ± 0.1 mm

Dimension drawing JAO18

302.0 ± 0.1 mm

308.2 ± 0.1 mm

66.0 ± 0.1 mm 62.5 ± 0.1 mm165.7 ± 0.1 mm 99.6 ± 0.1 mm87.8 ± 0.1 mm

Image 5-2

482.0 ± 0.1 mm

48.0 ± 0.1 mm

32.1 ± 0.1 mm

K5903250 JAO15 / JAO18 10/03/2016 33