Barco Imagepro-ii JR User Manual

Visibly yours

ImagePRO-II Jr

Quick Start Guide

Barco Events USA

3078 Prospect Park Drive Rancho Cordova, CA 95670 • USA

Phone:

Fax:

Technical Support:

Websites:

+1 (916) 859-2500 +1 (916) 859-2515 +1 (866) 374-7878 www.barco.com www.events.barco.com

EMEA Support

Website:

Phone:

www.barco.com/support/eSupport.aspx 0800900410

Ethernet

Connect to Web

Interface or

external controller.

Ethernet100-240VAC 50-60Hz, 2A

Connect to AC

power source.

DVI-I Input with

Loop-through

Connect to DVI

Universal DVI-IIn Loop

In Universal Analog Loop

Analog Input

with Loop-

through

Connect to

HD-15 sources.

Quick Install and Setup

Getting Started

1. Connect power — Ensure that power is properly connected to the ImagePRO-II Jr.

2. Connect inputs — Connect all input sources to the ImagePRO-II Jr.

3. Connect outputs — Connect the output(s) on the ImagePRO-II Jr to your projector(s) or other target devices.

4. Turn on power — Turn on power to the ImagePRO-II Jr, your projector(s), and to all peripheral equipment.

5. Factory reset — If you are using the ImagePRO-II Jr for the first time, or if you are using an ImagePRO-II Jr that has just returned from an event, perform a full factory reset to restore default system configurations.

sources.

SDI In SDI Out

SDI Input

Connect to

SD-SDI or HD-

SDI sources.

Setting Up Outputs

6. Obtain the output format — If the primary output is connected to a DVI-D or HD-15 connector, obtain the output’s preferred resolution and frame rate using the Output Menu. This is the format the ImagePRO-II Jr uses. (Chapter 4, “Using EDID Auto Config” section)

7. Adjust output format — If the primary output is connected to the SDI connector, you can adjust the output format manually to a SMPTE standard if necessary. (Chapter 4, “Setting Output Format” section)

8. Test output — Turn on a test pattern, verify that you have an image, and make any necessary adjustments. When complete, turn off the test pattern. (Chapter 4, “Working with Test Patterns” section)

9. Save output configuration — After completing output adjustments, save the output configuration.

DVI-D Output

Connect to DVI

video display.

DVI-D OUT

Genlock

Connect a

reference signal

such as black

burst or

composite sync.

SDI

Output

Connect to

SDI display.

Analog Out

ETHERNET

Analog Output

Connect to

analog

display.

Setting up an LED Display

10. Position and adjust the image — Use the LED Setup Menu to position the image on the LED wall or other display device, scale the image, adjust pan and zoom settings, and save your view. (Chapter 4, “Positioning an Image on the Display” section.)

Setting Up System Parameters and Inputs

11. Adjust and save system settings — Adjust system parameters such as VFD brightness, Ethernet settings, and HDCP parameters. (Chapter 4, “Using the System Menu” section.)

12. Set and adjust inputs — Select inputs and make any necessary adjustments to color balance, timings, sizing, etc. (Chapter 4, “Configuring Inputs” section.)

13.Save input configuration — After adjusting an input, save the input configuration. (Chapter 4, “Saving an Input Configuration” section.)

ImagePRO-II User’s Guide

For complete details on all installation and operations procedures, please refer to the ImagePRO-II User’s Guide.

Loop

P/N 26-0904104-00, Rev. 00

Visibly yours

Display Screen

Displays menus and

messages

ImagePRO-II Jr

Quick Start Guide

Adjust Knob

Navigate through

menus

Barco Events USA

3078 Prospect Park Drive Rancho Cordova, CA 95670 • USA

SEL and ESC

Buttons

Select an item, answer a query, or exit a menu

Phone:

Fax:

Technical Support:

Websites:

Input Buttons

Activate an input

+1 (916) 859-2500 +1 (916) 859-2515 +1 (866) 374-7878 www.barco.com www.events.barco.com

EMEA Support

Website:

www.barco.com/support/eSupport.aspx 0800900410

Phone:

BARCO

ImagePRO-II

IN:

Genlock: EXT

CH A:

1280x 1024 @60

USB Port

Connect a flash drive to back up or restore

logos, configuration, and load software

Features Overview

High-resolution Athena scaler

Selectable HDCP compliance on DVI connectors

Transitions through black or a logo

1 rack-mount chassis (1RU)

Loop-through on DVI and HD-15 inputs

Dedicated Genlock BNC connector with loopthrough

Ethernet connection

Front panel USB port

Programmable input and Auto Output Config for Extended Display Identification Data (EDID)

Multiple output synchronization modes, including analog, digital, SOG/Y

Front panel lock

Button States

Lit – Button is selected.

Dim – Source or logo is present but not active.

Not lit – Button is not selected and source is

not present.

™

1024x 768 @60

RGB

MENU KEYS

SETUP

PAN/

ZOOM

TEST

PAT

ADJUST

SEL

ESC

Quick Menu Access

Open the Setup, Test Pattern, or

Zoom/Pan Menus

Remote Control Options

Web Interface – Enables access from a computer, smartphone, tablet, or other web-enabled device.

Barco Encore Controller – An integral part of the Encore Presentation System, providing advanced video processing and presentation control for a wide variety of show configurations.

ScreenPRO-II Controller – A high-resolution multilayer seamless switching video display system for live event staging and fixed installation applications.

Analog Format Connection Table

Breakout

Cable Wire

Color

H Sync

V Sync

Comp Video

S-Video

(Y/C)

(Lum) (Lum)

(Chrom)

YUV

(YPbPr)

(Pr)

(Pb)

RGB SOG

RGB

Comp

Sync

RGB

Separate

H V

INPUTS

SDIDVI-I HD-15

LOGO

BLACK

FRZ

Effects Buttons

Transition to Logo or Black, or

Freeze an image

Overview of Key Operations Menus

Input Menu. Set input format; adjust brightness and contrast; adjust aspect ratio; set color balance; size the image; save and manage input configurations.

Output Menu. Set output format; Auto Config (detect output EDID); create an Area of Interest; adjust timing and colorspace; set effects such as sharpness, strobe mode, color inversion; manage Genlock settings.

Custom Formats. Create, save, delete custom input and output formats.

Views Menu. Save, recall, delete pan and zoom settings.

Transition Menu. Set transition timing and effects.

System Menu. Set system-wide params; manage input/

output HDCP settings; USB backup of logo/configs; set Ethernet options, set input EDID formats, lock front panel.

Logo Menu. Capture, delete, restore, erase, back up, and detect presence of logos.

LED Setup Menu. Quickly set up output Area of Interest, input scaling, and save the settings.

Factory Reset. Restores factory default settings. Optionally, keep IP address.

Code Upgrade. Update ImagePRO-II Jr firmware from a flash drive, or check for available upgrades over the web.