Barco ImagePRO-II Dual Output User Manual

ImagePRO-II Dual Output

• Manual #: 26-0904001-00

• Revision: 00

User’s Guide Addendum

User’s Guide Addendum

Copyright

© Barco. June 12, 2012
All rights reserved. No part of this document may be copied, reproduced or translated. It
shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior
written consent of Barco.

Notice

Barco provides this manual “as is” without warranty of any kind, either expressed or
implied, including but not limited to the implied warranties or merchantability and fitness for
a particular purpose. Barco may make improvements and/or changes to the product(s) and/
or the program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are
periodically made to the information in this publication; these changes are incorporated in
new editions of this publication.

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area may cause harmful interference, in which case the user will be responsible for
correcting any interference.

Guarantee and Compensation

Barco provides a guarantee relating to perfect manufacturing as part of the legally
stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all
delivered goods for damage incurred during transport, as well as for material and
manufacturing faults Barco must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special
systems and software on the date of commissioning, at latest 30 days after the transfer of
risks. In the event of justified notice of compliant, Barco can repair the fault or provide a
replacement at its own discretion within an appropriate period. If this measure proves to be
impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or
cancellation of the contract. All other claims, in particular those relating to compensation for
direct or indirect damage, and also damage attributed to the operation of software as well
as to other services provided by Barco, being a component of the system or independent
service, will be deemed invalid provided the damage is not proven to be attributed to the
absence of properties guaranteed in writing or due to the intent or gross negligence on the
part of Barco.

If the purchaser or a third party carries out modifications or repairs on goods delivered by
Barco, or if the goods are handled incorrectly, in particular if the systems are commissioned
operated incorrectly or if, after the transfer of risks, the goods are subject to influences not
agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid.

26-0904001-00 Rev 00.00 2

Not included in the guarantee coverage are system failures which are attributed to
programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal
wear as well as normal maintenance are not subject to the guarantee provided by Barco
either.

The environmental conditions as well as the servicing and maintenance regulations
specified in this manual must be complied with by the customer.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered
trademarks or copyrights of their respective holders. All brand and product names
mentioned in this manual serve as comments or examples and are not to be understood as
advertising for the products or their manufactures.

Company Address

Barco, Inc.

11101 Trade Center Drive
Rancho Cordova, California 95670
USA

•

Phone: [phone]

•

Fax: [phone]

•

Website: www.barco.com

Barco N.V.

Noordlaan 5
8520 Kuurne
BELGIUM

•

Phone: [phone]

•

Fax: [phone]

•

Website: www.barco.com

Technical Support (USA)

•

Customer Service Portal — www.barco.com/esupport

• Phone:

week

Technical Support (Europe, Middle East, Asia)

• Telephone: [phone]

• Online: www.barco.com/support/eSupport.asp

[phone] —

— 6 a.m. to 10 p.m. (PST), 7 days per

26-0904001-00 Rev 00.00 3

Operators Safety Summary

The general safety information in this summary is for operating personnel.

Do Not Remove Covers or Panels

There are no user-serviceable parts within the unit. Removal of the top cover will expose
dangerous voltages. To avoid personal injury, do not remove the top cover. Do not operate
the unit without the cover installed.

Power Source

This product is intended to operate from a power source that will not apply more than 230
volts rms between the supply conductors or between both supply conductor and ground. A
protective ground connection by way of grounding conductor in the power cord is essential
for safe operation.

Grounding the Product

This product is grounded through the grounding conductor of the power cord. To avoid
electrical shock, plug the power cord into a properly wired receptacle before connecting to
the product input or output terminals. A protective-ground connection by way of the
grounding conductor in the power cord is essential for safe operation.

Use the Proper Power Cord

Use only the power cord and connector specified for your product. Use only a power cord
that is in good condition. Refer cord and connector changes to qualified service personnel.

Do Not Operate in Explosive Atmospheres

To avoid explosion, do not operate this product in an explosive atmosphere.

26-0904001-00 Rev 00.00 4

Change History

The table below lists the changes to the User’s Guide Addendum.

Rev Date ECP # Description Approved By

00 6/22/12 597847 Initial Release R. Pellicano

26-0904001-00 Rev 00.00 5

Table of Contents

Introduction....................................................................... 7

1. Getting Started .............................................................. 7

2. Initial Setup ................................................................... 7

To enable Dual Channel Mode ................................................................................... 7

Setting up the Output Connector Map ........................................................................ 8

3. Output Configuration ..................................................... 9

Output Resolution ................................................................................................... 9

Area of Interest ...................................................................................................... 9

Output Timing Adjustment ....................................................................................... 9

Output Effects ...................................................................................................... 10

Genlock ............................................................................................................... 10

Save and Reset Output Configs ............................................................................... 11

Pan / Zoom .......................................................................................................... 11

Logo Backup and Restore ....................................................................................... 11

4. General Operation ........................................................ 12

5. Remote Commands ...................................................... 13

ICH ..................................................................................................................... 13

IMGR ................................................................................................................... 14

STMGR ................................................................................................................ 15

OCON .................................................................................................................. 15

SYSMGR .............................................................................................................. 16

UINPUT ............................................................................................................... 16

VFS ..................................................................................................................... 17

VIDCOL ............................................................................................................... 17

VIEW ................................................................................................................... 18

VIDREF ................................................................................................................ 19

26-0904001-00 Rev 00.00 6