Page 1
UserUser’s manual’s manual
KVD5521, IVD5521, HVD5521
Page 2
Page 3
User's manual
KVD5521, IVD5521,
and HVD5521
Page 4
Page 5
Title: KVD5521, IVD5521, and HVD5521 user manual
Date: November-2016
ProdID: R591341
Revision: 05
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
__________________________________________________________
i
Page 6
Copyright © 2014-2016 by Barco
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be
recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.
Factory Address:
KORTEK Corporation
26, Venture-ro 24 (isipsa)beon-gil, Yeonsu-gu
Incheon 406-840, Republic of Korea
ii
_______________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 7
WARRANTY STATEMENT
Hardware warranty
The warranty period commences at the date of shipment from Barco.
• The Seller warrants the equipment manufactured by the Seller against defects in workmanship and material,
under normal use and in accordance with its specifications, during the period of 36 months for the electronics
and 36 months for the panel and backlight from the aforementioned date. Any part of the equipment which
is wholly manufactured by third parties is guaranteed under the conditions of such manufacturer and no separate warranty is given in respect thereof by the Seller.
• Image retention is not covered by warranty in any case.
Recommendation is to use the display not longer than 20hrs per day for static images.
• Light leakage on the borders is not covered by warranty in any case.
The LED backlight might be visible around the ultra narrow bezels in case of black screen content on the borders of the display and in dark rooms.
• In the event of a defect in workmanship or material, the Seller will be obliged, at its choice and best effort
base, to replace or repair the defective equipment. The replacement part will be in good working order and
at least functionally equivalent to the item replaced.
• The warranty does not apply when the cause of the failure occurs after delivery of the equipment to the
Purchaser and results from abnormal conditions of operation, unauthorized access, improper use, unauthorized modification, lack of normal maintenance or unauthorized attempts to repair the equipment. A failure to
follow these requirements can result in delay and additional costs that will be invoiced to the purchaser.
• The Purchaser must notify the Seller of any complaint within eight days of discovery of any alleged defect.
Failure by the Purchaser to so notify the Seller will relieve the Seller of its obligations under this article.
• The foregoing warranty will not apply if any payment remains outstanding from the Purchaser to the Seller.
• All items, parts or components which are replaced by the Seller under warranty or otherwise shall become
the property of the Seller. All defective parts need to be sent back to the Seller.
• The replacement parts are free of charge during the warranty period.
• The Seller will ship the replacement parts to the Purchaser on a CIF (cost insurance and freight) base. At the
same time the Seller will issue a RMA number for returning the defective parts.
• Traveling and Lodging of the service engineer will be invoiced to the Purchaser according to the Time & Ma-
terial Pricing rules of the Seller.
• On site labor of the service engineer will be invoiced to the Barco National Organization or Sales Partner
according to the Time & Material Pricing rules of the Seller.
• The remedies described above are Purchaser's sole remedies in the event of any breach of the warranty
provided above.
• Consumables are excluded from warranty.
• The warranty period of repairs and spare parts is 3 months, or at minimum the original warranty period of
the system.
• The seller does no warrant uninterrupted or error-free operation of the installation
• The foregoing warranty is in lieu of all other warranties, whether oral, written, express, implied or statutory.
No implied or statutory warranties of merchantability or fitness for a particular purpose shall apply and all
warranties, conditions or other terms implied by statute or common law are hereby excluded.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_________________________________________________________
iii
Page 8
Software warranty
The Seller makes no warranties with respect to the software and technical information and, such items are provided to the Purchaser on an "as-is" basis without warranty of any kind, including the warranties of merchantability and fitness for a particular purpose.
• The Purchaser acknowledges and agrees that the software provided by the Seller to the Purchaser in an
unmodified form is designed to operate with the hardware identified in the Certificate of Installation and
Operation, provided (i) the hardware is unmodified and (ii) the software, as unmodified, operates in conjunction with the proper computer equipment as designated in the Special Conditions.
• The Purchaser agrees to indemnify, defend and hold harmless the Seller from and against all claims, liabili-
ties, losses, damages and costs and expenses arising out of or resulting from the combination or integration
of the hardware and/or software with any item of any kind not furnished by the Seller.
iv
______________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 9
Revision sheet
To:
•
Barco Control Room GmbH
Greschbachstrasse 5a, D-76229 Karlsruhe
Phone: +49-721-6201-0, Fax: +49-721-6201-298
E-mail:
docu.bcd.de@barco.com, Web: www.barcocontrolrooms.com
From:
Date:
Please correct the following points in this documentation:
page wrong correct
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
__________________________________________________________
v
Page 10
Contents
1 Preliminary Remarks .................................................................................................................................. 9
1.1 Styles and symbols ........................................................................................................................................... 10
1.2 Safety information ............................................................................................................................................ 11
1.2.1 Safety on installation ................................................................................................................................ 12
1.2.2 Intended use ............................................................................................................................................ 14
1.2.3 Storage and transportation ........................................................................................................................ 14
1.2.4 Unpacking of Devices ................................................................................................................................ 14
1.2.5 Importers contact information .................................................................................................................... 14
1.2.6 Made in information ................................................................................................................................. 14
1.2.7 Production date ........................................................................................................................................ 14
1.2.8 Certifications ............................................................................................................................................ 14
1.2.9 Safety on servicing ................................................................................................................................... 17
1.2.10 Safety instruction on opening systems built into a structure ....................................................................... 18
1.2.11 Safety on shipping .................................................................................................................................. 19
1.2.12 Precautions ............................................................................................................................................ 19
1.2.13 Malfunction or Trouble ............................................................................................................................ 20
1.2.14 Unpacking of devices .............................................................................................................................. 20
1.2.15 Modification of devices ........................................................................................................................... 20
1.2.16 Cleaning ................................................................................................................................................. 21
1.2.17 Moving the product ................................................................................................................................. 21
1.2.18 Disposal or handing over to a new owner ................................................................................................. 21
1.2.19 Environmental information: disposal information ....................................................................................... 22
1.2.20 Exemptions ............................................................................................................................................ 22
1.2.21 Energy saving design .............................................................................................................................. 23
2 Unpacking and installation ........................................................................................................................ 25
2.1 Unpacking ........................................................................................................................................................ 25
2.2 Moving and handling the display ........................................................................................................................ 26
2.3 Installation ....................................................................................................................................................... 27
2.3.1 VESA compliant mounting solution ............................................................................................................. 28
2.3.2 Portrait mode ........................................................................................................................................... 28
2.3.3 Dimensions of KVD5521 AND IVD5521: ....................................................................................................... 29
2.3.4 Dimensions of HVD5521: ........................................................................................................................... 30
2.4 Examining the display ....................................................................................................................................... 31
2.4.1 Rear view ................................................................................................................................................ 31
3 Cabling ................................................................................................................................................... 33
3.1 Signal cabling ................................................................................................................................................... 33
3.2 IR Remote Control cabling.................................................................................................................................. 33
3.3 Connecting devices ........................................................................................................................................... 34
3.3.1 PC 34
3.3.2 LAN connection ........................................................................................................................................ 35
3.3.3 Connecting to an HD receiver, DVD, Camcorder, Camera, Gaming Device or VCR player .................................. 36
3.4 Communication cabling ..................................................................................................................................... 36
vi
______________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 11
3.4.1 IR receiver ............................................................................................................................................... 36
3.4.2 IR Remote Control ..................................................................................................................................... 37
3.5 Power cabling ................................................................................................................................................... 39
3.5.1 Switching on and off ................................................................................................................................. 39
3.6 Installation of an OPS ........................................................................................................................................ 40
4 Design and function ................................................................................................................................. 41
4.1 Display of choice ............................................................................................................................................... 41
4.2 Cooling concept ................................................................................................................................................ 41
4.3 Option: EnergyStar compliance for the entire display wall .................................................................................... 42
4.4 Multiple sources, native resolution ..................................................................................................................... 43
4.5 Space saving .................................................................................................................................................... 43
4.6 Front access ...................................................................................................................................................... 43
4.7 Barco Wall Control Manager (BCM) ..................................................................................................................... 43
4.8 Web interface ................................................................................................................................................... 44
5 Data processing ....................................................................................................................................... 45
5.1 Scaling ............................................................................................................................................................. 45
5.2 Loop-through, scaling, and splitting .................................................................................................................... 47
5.2.1 No scaling and no splitting ........................................................................................................................ 47
5.2.2 Splitting and scaling .................................................................................................................................. 48
5.3 Summary .......................................................................................................................................................... 50
6 SenseX ................................................................................................................................................... 51
6.1 Theory ............................................................................................................................................................. 51
6.2 Principle of color locking and brightness locking .................................................................................................. 52
6.3 Color sensor (colorimeter) ................................................................................................................................. 53
6.4 Color & Brightness Modes .................................................................................................................................. 53
6.4.1 Native ..................................................................................................................................................... 53
6.4.2 SenseX ..................................................................................................................................................... 53
7 Web interface .......................................................................................................................................... 55
8 Barco Wall Control Manager (BCM) ............................................................................................................. 57
8.1 General ............................................................................................................................................................ 57
8.2 Cabling ............................................................................................................................................................. 57
9 Maintenance and servicing ........................................................................................................................ 61
9.1 Cleaning ........................................................................................................................................................... 63
10 Technical data ........................................................................................................................................ 65
10.1 Display capabilities .......................................................................................................................................... 65
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
________________________________________________________
vii
Page 12
10.2 Operating performance .................................................................................................................................... 65
10.3 Mechanical KVD5521 AND IVD5521 ................................................................................................................... 65
10.4 Mechanical HVD5521 ....................................................................................................................................... 66
10.5 Power ............................................................................................................................................................ 66
10.6 Signal connectors and supported resolutions ..................................................................................................... 66
10.7 Wall control .................................................................................................................................................... 66
10.8 Environmental and regulation compliance ......................................................................................................... 67
10.9 Light Leakage KVD/IVD .................................................................................................................................... 67
10.10 Light Leakage HVD ......................................................................................................................................... 67
10.11 Cosmetic specification .................................................................................................................................... 68
10.11.1 Inspection conditions ............................................................................................................................. 68
10.11.2 Definition of dot defect ......................................................................................................................... 68
10.11.3 Dot classification method ....................................................................................................................... 68
10.11.4 Definition of uniformity defect ............................................................................................................... 69
10.11.5 Spot and linear type inspection .............................................................................................................. 69
11 Interfaces .............................................................................................................................................. 71
11.1 DVI-D, single link ............................................................................................................................................ 71
11.2 HDMI Type A ................................................................................................................................................... 71
11.3 DisplayPort ..................................................................................................................................................... 72
11.4 S/PDIF connector (TOSLINK) ............................................................................................................................. 72
11.5 USB connector ................................................................................................................................................. 73
11.6 OPSconnector .................................................................................................................................................. 73
12 DDC Files programmed in the display ........................................................................................................ 77
12.1 DisplayPort ..................................................................................................................................................... 77
12.2 HDMI .............................................................................................................................................................. 78
12.3 DVI ................................................................................................................................................................ 79
13 Troubleshooting ..................................................................................................................................... 81
13.1 Faults ............................................................................................................................................................. 81
13.2 Contact ........................................................................................................................................................... 82
14 Compliance statement ............................................................................................................................ 83
14.1 FCC Compliance statement ............................................................................................................................... 83
14.1.1 Declaration of Conformity ........................................................................................................................ 83
14.2 Canadian DOC Notice ....................................................................................................................................... 84
14.3 Chinese Mainland RoHS.................................................................................................................................... 85
viii
_____________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 13
1. Preliminary Remarks
1 Preliminary Remarks
This manual describes Barco's displays KVD5521, IVD5521, HVD5521. In this manual hey will be referred to as
“xVD” displays.
xVD displays excel in high brightness, high contrast, wide viewing angle, high color saturation, super narrow
bezel, and direct LED backlight.
They feature a resolution of 1920x1080, versatile inputs, integrated streaming, cropping and scaling capabilities.
As the first and only manufacturer, Barco now introduces its SenseX automatic color and brightness calibration
system, that lets you calibrate the complete wall within minutes, without any external sensor or manual intervention. The result is a LCD video wall which is perfectly balanced in terms of colors and brightness,
Together with Barco’s wall mounting solutions, display wall management software and wall calibration, the xVD
displays are the perfect solution for LCD video wallf for high end applications.
KVD5521 Display with a screen diagonal of 55inch, TFT LCD technology, HD resolution
(1920x1080 pixels), aspect ratio 16:9
IVD5521 Display with a screen diagonal of 55inch, TFT LCD technology, HD resolution
(1920x1080 pixels), aspect ratio 16:9, high brightness
HVD5521 Display with a screen diagonal of 55inch, TFT LCD technology, HD resolution
(1920x1080 pixels), aspect ratio 16:9, high brightness
Next to Barco's wall mount solutions, 3rd party mounting solutions are available for small (2x2, 3x2) video walls.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_________________________________________________________
9
Page 14
1. Preliminary Remarks
1.1 Styles and symbols
The typographic styles and the symbols used in this document have the following meaning:
Bold Labels, menus and buttons are printed in Bold font.
Condensed Links to both other chapters of this manual and to sites in the Internet are printed
condensed. In the on-line version of this manual all hyperlinks appear teal.
Courier
Names of files and parts from programs are printed in the
Courier
font.
Courier bold
Inputs you are supposed to do from the keyboard are printed in
Courier bold
font.
If you do not heed instructions indicated
by this symbol there is a risk of damage
to the equipment!
Le non-respect des instructions symbolisées par
ce pictogramme entraînera un risque de
dommage de l'équipement ! �
If you do not heed instructions indicated
by this symbol there is a risk of electrical
shock and danger to personal health!
Le non-respect des instructions symbolisées par
ce pictogramme entraînera un risque de
décharge électrique et sera source de danger
pour la santé du personnel ! �
If you do not heed instructions indicated
by this symbol there is a risk of damage
to parts, which are sensitive towared
electrostatic charge!
Le non-respect des instructions symbolisées par
ce pictogramme entraînera un risque de
dommage de pièces sensibles à la charge
électrostatique ! �
If you do not heed instructions indicated
by this symbol there is a risk to get
harmed by sharp objects!
Le non-respect des instructions symbolisées par
ce pictogramme entraînera un risque de
blessure dû à des objets tranchants !
If you do not heed instructions indicated
by this symbol there is a risk that parts
may explode!
Le non-respect des instructions symbolisées par
ce pictogramme entraînera un risque
d'explosion de pièces ! �
If you do not heed instructions indicated
by this symbol there is a risk that hot
parts impact persons or objects!
Le non-respect des instructions symbolisées par
ce pictogramme entraînera un risque de contact
de personnes ou d'objets avec des pièces
chaudes !
The sheet icon indicates additional notes.
Cette icône représentant une feuille indique
des remarques supplémentaires.
Next to this icon you find further
information.
Cette icône est suivie d'informations plus
détaillées. �
This hand marks tips. Cette icône attire l'attention sur des conseils.
Next to this icon you find important
notes.
Cette icône est suivie de remarques
importantes.
10
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 15
1. Preliminary Remarks
1.2 Safety information
This section describes safety precautions which must be observed when installing a product from Barco.
Safety standards
xVD5521 displays (KVD5521, IVD5521, HVD5521 displays) are built in accordance with the requirements of the
international safety standards EN 60950-1 (2006) + A11 (2009) + A1 (2010) + AC (2011) + A12 (2011) + A2
(2013) and IEC 60950-1. xVD5521 conform to UL std. UL 60950-1 and is certified to CSA std. C22.2 No. 60950-1
and Chine Compulsory Certifcation CCC. All these safety standards are the information technology equipment
standards, including electrical business equipment.
These safety standards impose important requirements on the use of safety critical components, materials and
isolation, in order to protect the user or operator against the risk of electric shock and energy hazard, and having
access to live parts.
Safety standards also impose requirements to the internal and external temperature variations, radiation levels,
mechanical stability and strength, enclosure construction and protection against risk of fire.
Simulated single fault condition testing ensures the safety of the equipment to the user even when the equipment's normal operation fails.
Electromagnetic Interference
xVD5521 comply with the following EMC standards:
Electromagnetic compatibility emission:
EN 55022 (2010) + AC (2011)
EN 55032 (2012) + AC (2013)
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
Electromagnetic compatibility immunity:
EN 55024 (2010)
Make sure to use cables with shielding of
type S-FTP or S-STP when connecting the
display to the network!
Assurez vous d'utiliser des câbles avec un
blindage de type S-FTP ou S-STP lors de la
connexion de l’écran au réseau!
EN55022/CISPR22 Class B ITE (Information Technology Equipment)
xVD5521 devices are products of class B ITE. ITE means Information Technology Equipment. ITE is subdivided into
two categories denoted class B ITE (products intended primarily for use in domestic environment) and class A ITE
(all other ITE which satisfies the class A ITE limits but not the class B ITE limits).
FCC Compliance statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However there is no
guarantee that interferences will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception (which can be determined by
turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
11
Page 16
1. Preliminary Remarks
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not
expressly approved by the party
responsible for compliance could void
the user's (or your) authority to
operate the equipment. Only
peripherals (digital input/output
devices, terminals, printers, etc.)
certified to comply with the Class B
limits may be attached to this display.
Operation with non-certified
peripherals is likely to result in
interference to radio and TV reception.
Only shielded signal cables may be
used with this System.
Attention: Des changements ou modifications
non expressément approuvés par la partie responsable de la conformité pourraient annuler
l'autorité de l'utilisateur ou la votre pour utiliser
l'équipement. Seuls les périphériques (entrée
numérique / périphériques de sortie, terminaux,
imprimantes, etc) certifiés comme étant conformes aux limites de la classe B peuvent être
connectés à cet écran. L'utilisation de périphériques non conformes peut provoquer des interférences dans la réception radio et télévision.
Seuls des câbles blindés peuvent être utilisés
avec ce système
The regulations are applied only to
the products with the ID LABEL
indicating specific requirements.
Les règlements sont appliqués que pour les produits avec l'étiquette d'identification indiquant
les besoins spécifiques.
General safety instructions
• All the safety and operating instructions should be read before using this unit.
• The operating instructions manual should be retained for future reference.
• All warnings on the device and in the documentation manuals should be adhered to.
• All instructions for operating and use of this equipment must be followed precisely.
• All local installation codes should be adhered to.
Installation and preliminary
adjustments should be performed by
qualified Barco personnel or
authorized Barco service dealers.
Installation et réglages préliminaires devraient
être effectués par du personnel qualifié de Barco
ou les revendeurs autorisés par Barco
1.2.1 Safety on installation
Check the power rating on your outlet before connecting the devices to
the AC inlet. Contact your facilities
manager or a qualified electrician if
you are not sure what type of power
is supplied to your building.
Vérifiez la puissance sur la prise avant de brancher les appareils sur la prise secteur. Contactez
votre gestionnaire des installations ou un électricien qualifié si vous n'êtes pas sûr du type d'alimentation fourni dans votre bâtiment
The devices are designed to operate
with single-phase power systems
having a grounded neutral conductor. To reduce the risk of electrical
shock, do not plug into any other
type of power system.
Les dispositifs sont conçus pour fonctionner avec
les systèmes d'alimentation monophasés avec
conducteur neutre à la terre. Pour réduire le
risque de choc électrique, ne branchez pas sur un
autre type de système d'alimentation.
12
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 17
1. Preliminary Remarks
1.2.1.1 Connecting the device with the AC inlet
When connecting the device with the AC inlet, make sure that the power cords you use follow the specifications
mentioned below:
Mains lead (AC Power cord) with CEE 7 plug:
The wires of the mains lead are colored in accordance with the following code:
yellow + green
Earth (Ground)
blue
Neutral
brown
Line (Live)
Power cord with NEMA 5-15 plug:
The wires of the power cord are colored in accordance with the following code.
Green or Green/Yellow:
Earth (Ground)
White or Blue:
Neutral
Black or Brown:
Line ( Live)
• The cord set must be UL-approved and CSA-certified.
• The minimum specification for the flexible cord is No. 18 AWG Type SVT or SJT, 3-conductor.
• The cord set must have a rated current capacity of at least 10A.
• The attachment plug must be an Earth-grounding type with a NEMA 5-15P (10 A, 125 V) configuration.
Power cord with GB 2099 plug:
The wires of the power cord are colored in accordance with the following code.
yellow + green
Earth (Ground)
blue
Neutral
brown
Line ( Live)
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
13
Page 18
1. Preliminary Remarks
• Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the
cord.
• To disconnect the cord, pull it out by the plug. Never pull the cord itself.
• Do not touch the power cord with wet hands. If the cord pin is wet or covered with dust, dry the power plug
completely or wipe dust off.
• Fix the power cable completely.
• Do not unplug the power cord while the product is in use.
• As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even
if the unit is turned off.
• If an extension cord is used with this product, make sure that the total of the ampere ratings on the products
plugged into the extension cord does not exceed the extension cord ampere rating. Also make sure that the
total of all products plugged into the wall outlet does not exceed 15 amperes.
• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a risk of fire or electrical shock.
• Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the
set and have it checked by qualified service personnel before resuming operations.
• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the display
due to lightning and AC power-line surges.
Do not place flammable or combustible
materials near the display!
Ne placez pas de matériaux inflammables ou
combustibles près de l'écran!
1.2.2 Intended use
The displays are intended for professional use only in Barco Control Room applications.
The displays are not for household use.
1.2.3 Storage and transportation
Units have to be stored and transported in the original packaging in accordance with the non-operating conditions, 10.7 Environmental and regulation compliance
1.2.4 Unpacking of Devices
Note advises on the packaging for unpacking!
Only unpack for immediate installation!
1.2.5 Importers contact information
To find your local importer, contact Barco directly or one of Barco’s regional offices. Use the contact information
given on the official Barco web site http://www.barco.com.
1.2.6 Made in information
For the country the product has been manufactured in, please check the product ID label on the product itself
1.2.7 Production date
For month and year of production, please check the product ID label on the product itself
1.2.8 Certifications
See the product label for approval marks.
14
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 19
1. Preliminary Remarks
Transportation
• Any transportation of the unopened unit in its packaging should be done by two persons.
• In transportation or storage of products in original packing, NEVER stack more than the number stated on the
carton box. This warning is also indicated on the side of the card box.
• For transportation or storage, observe the warnings and instructions on the side of the card box.
Nearby equipment
If air conditioning ducts or lamps, etc. are located near the installation site, the attendant dust, extreme temperatures, humidity, and condensation may become sources of trouble. Please take sufficient steps to avoid this.
Installation places
Do not install the unit where it may be easily touched or leaned against. Avoid locations subject to high vibrations or severe impacts. Do not install the unit where it is exposed to humidity, oil, smoke or excessive dust.
Mount the display in a well ventilated area away from sources of ignition and out of direct sun light. Never expose this product to rain or excessive moisture.
If you install the product in a place where there is an abundance of fine dust, chemical substances are used, the
temperature is very high or low, the humidity is very high, or the product is likely to remain turned on for a long
period of time this might cause serious damage to the product's picture quality, life cycle and appearance.
Install the unit on a neat and dry place.
Install the unit on a flat and stable place.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
15
Page 20
1. Preliminary Remarks
Operating the product
Take a rest from time to time to protect your vision.
Take a regular break when working with the product for a long time.
Keep the proper distance from the product. Your vision may be impaired if you look at the product too closely.
Using headsets (earphones) for a long time or listening loudly can cause damage to your hearing.
LED inside!
Class 1M laser (LEDs) radiation when open.
Do not open while operating!
LED à l'intérieur!
Rayonnement Laser de classe 1M (LEDs)
lorsqu'il est ouvert.
Ne pas ouvrir pendant le fonctionnement!
Mechanical stress
Please be careful not to apply strong mechanical stress (shock, drop) to the LCD module. Such stress may cause
break of screen glass or may be the cause for failure.
Pressure to screen surface
Please be careful not to apply strong pressure to the screen surface. Such pressure may cause scratches at the
surface or may be the cause of failure.
Protection against scratch
Please be careful not to hit, press or rub the screen surface with hard material like tools. In addition, please do
not put heavy or hard material on the screen surface, and do not stack displays. Polarizer at the front surface can
be easily scratched.
Temperature dependence of the display
Response speed (optical response) of the LCD display is dependent on temperature. Under low temperature,
response speed is slower. Also brightness and chromaticity change slightly depend on temperature.
Image retention
This product can be used in 24/7 when no static content is applied; when static content is applied BARCO recommends switching off the panels 4 hours a day to limit the possibility to incur in technology related phenomena such as Image retention and burn in. Running at a reduced brightness level and optimizing the room cooling
system to limit the heat on the screen is also advised. For more information contact Barco for a white paper on
this topic.Lighting conditions
Consider existing lighting and sunlight angles when creating the installation layout. Extremely bright lightning
can reduce the visibility and the quality of the displayed image.
In extremely bright surroundings, adjusting screen intensity may not result in perceptibly brighter images. Keep
in mind that extreme intensity settings can reduce system service life.
Barco products are designed and manufactured to meet the most stringent safety regulations. Exposing flammable or combustible materials into close proximity of this device could result in the spontaneous ignition of that
material, resulting in a fire. For this reason, it is absolutely necessary to leave an "exclusion zone" around all
external surfaces of the display whereby no flammable or combustible materials are present. The exclusion zone
must be not less than 10 cm (4"). Do not cover the display with any material while it is in operation.
Keep flammable and combustible materials away from the display at all times. Mount the display in a well ventilated area away from sources of ignition and out of direct sun light. Never expose this product to rain or excessive moisture. In the event of fire, use sand, CO2, or dry powder fire extinguishers; never use water on an electrical fire.
Always have service performed on this product by authorized Barco service personnel. Always insist on genuine
Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this device.
Use only the power cord which fulfill the specifications as listed in1.2.1.1 Connecting the device with the AC inlet. Slots
and openings in the cabinet and the sides are provided for ventilation; to ensure reliable operation of the device
and to protect it from overheating, these openings must not be blocked or covered. This product should never be
placed near or over a radiator or heat register. This product should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
16
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 21
1. Preliminary Remarks
1.2.9 Safety on servicing
Do not attempt to service this device yourself, as opening or removing covers may expose you to dangerous
voltage potential and risk of electric shock! Refer all display service to a qualified Barco service center.
Adjust only those controls that are covered by the operating instructions since improper adjustment of the other
controls may result in damage and will often require extensive work by a qualified technician to restore the
product to normal operation.
Call for service in the following conditions:
• When the power cord or plug is damaged or frayed.
• If liquid has been spilled into the device.
• If the product has been exposed to rain or water.
• If the product does not operate normally when the operating instructions are followed.
• If the product has been dropped or the cabinet has been damaged;
• If the product exhibits a distinct change in performance, indicating a need for service.
Replacement parts
When replacement parts are required, be sure the service technician has used original Barco replacement parts
or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized
substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty.
Safety check
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
Protection
Please do not disassemble or modify the LCD module to avoid the possibility of electric shock, damage of electronic components, scratch at display surface and invasion of foreign particles. In addition, such activity may
result in fire accident due to burning of electronic component.
The LCD module disassembled or modified by customer is out of warranty.
Le module LCD démonté ou modifié par le
client n'est plus sous garantie
Please be careful in handling of display with broken glass. When the display glass breaks, please pay attention
not to injure your fingers. The display surface has the plastic film attached, which prevents dispersion of glass
pieces; however touching broken edge will injure your fingers.
Please do not touch the fluid flown out of broken display glass. If the fluid should stick to hand or clothes, wipe
off with soap or alcohol immediately and then wash it with water.
If the fluid should get in your eyes, wash
your eyes immediately with pure water
for more than 15 minutes and then
consult the doctor.
Si le liquide entre en contact avec vos yeux,
lavez-vous immédiatement les yeux avec de
l'eau pure pendant plus de 15 minutes, puis
consulter le médecin.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
17
Page 22
1. Preliminary Remarks
1.2.10 Safety instruction on opening systems built into a structure
When doing maintenance work or changing
cables on a display built into a structure you
have to open all displays ABOVE the one you
want to work on.
Lors de travaux de maintenance ou pour
changement de câbles sur un écran intégré
dans une structure, vous devez ouvrir tous
les écrans au-dessus de celui que vous voulez travailler.
When a display which is built into a
structure has to be de-mounted, first demount all displays above the one you
have to de-install and then close the
interfaces: This gives you free access to
the display you want to remove and
eliminates the risk of damaging the
display hanging above when moving the
system up!
Quand un écran qui est intégré dans une
structure doit être démonté, au préalable
démontez tous les écrans au-dessus de celui
que vous devez désinstaller puis fermez les
interfaces: Cela vous donne libre accès à
l'écran que vous souhaitez enlever et élimine
le risque d'endommager l'écran suspendu audessus lors du déplacement vertical du
système!
18
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 23
1. Preliminary Remarks
When opening a display which is built
into a structure, simultaneously press on
the left and right bottom sides of the
displays (there are the latches behind).
In case the interface frame does not open
you very probably have a mixed situation
of latches; one is opened, one closed.
Then only press on the left OR on the
right ot make the position of the latches
the same.
Lors de l'ouverture d'un écran qui est intégré
dans une structure, appuyez simultanément
sur les côtés inférieurs droit et gauche de
l’écran (il existe des loquets derrière).
Dans le cas où le cadre de l'interface ne s’ouvre
pas, très probablement vous faites face à une
situation mixte de loquets; un ouvert, un
fermé. Alors pressez sur celui de gauche ou de
droite, ou mettez les loquets dans la même
position.
1.2.11 Safety on shipping
Original shipping package
Save the original shipping packing material; they will come in handy if you ever have to ship one of your installed modules. For maximum protection, repack your set as it was originally packed at the factory.
Keep the packing anti-moisture material or vinyl packing out of the reach of children. Anti-moisture material is
harmful if swallowed. If swallowed by mistake force the patient to vomit and visit the nearest hospital.
Vinyl packing can cause suffocation. Keep it out of the reach of children.
1.2.12 Precautions
For your own protection, observe the following safety precautions!
• Observe all warnings and instructions printed on the devices!
• Check that the voltage and frequency of your power supply match those printed on the device label with the
rated electrical values!
• Servicing not explicitly mentioned in this manual should never be carried out by unauthorized personnel!
• Some parts of the body are hot during operation. Please be careful.
• In case of moving long-distance, wrap the unit with blanket to avoid damages. Be careful not to bump the
unit.
• Do not spray
Unused for long periods of time
For added protection for this video product during a lightning storm, or when it is left unattended an unused for
long periods of time, unplug it from the wall outlet. This will prevent damage to the LCD module due to lightning
and AC power-line surges
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
19
Page 24
1. Preliminary Remarks
1.2.13 Malfunction or Trouble
Trouble take the following steps risk of
Smoke or peculiar smells comes from
the unit
Remove the power plug from the outlet
immediately!
Make sure that the smoke or smell has
stopped, then contact your dealer for
inspection
fire or an electric shock
No picture Remove the power plug from the outlet
immediately!
Contact your dealer for inspection
fire or an electric shock
Water is spilled or objects are dropped
inside the unit
Remove the power plug from the outlet
immediately!
Contact your dealer for inspection
fire or an electric shock
The unit is dropped or the cabinet is
damaged
Remove the power plug from the outlet
immediately!
Contact your dealer for inspection
fire or an electric shock
The power cord or plug is damaged or
becomes hot
Power off the unit with the power
switch on the rear side.
When the power plug has cooled down,
remove the power plug from the wall
outlet!
Contact your dealer for inspection
fire or an electric shock
1.2.14 Unpacking of devices
Note advices on the packaging for unpacking!
Please refer to chapter 2 Unpacking and installation
1.2.15 Modification of devices
Mechanical or electrical modifications others than described in this manual must not be made to the devices.
Barco is not liable for damages resulting from modified devices.
Only authorized personnel should carry out
other maintenance work not explicitly
mentioned in this user's manual!
Never open the case of the display without
first disconnecting the device from the AC
inlet. Measurements and tests with an
opened device may be carried out only in
the factory or by specially trained personnel, due to the dangers of electrical shock.
Seul le personnel autorisé devrait effectuer
d'autres travaux d'entretien qui ne sont
pas explicitement mentionnées dans le
manuel de l'utilisateur!
Ne jamais ouvrir le boîtier de l'écran sans
avoir d'abord débrancher l'appareil de la
prise secteur. Mesures et essais avec un
dispositif ouvert peuvent être effectués
que dans l'usine ou par un personnel
spécialement formé, en raison des dangers
de décharge électrique.
20
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 25
1. Preliminary Remarks
1.2.16 Cleaning
• Disconnect the device from the AC inlet.
• Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame.
Scrub gently to prevent scratching.
Wipe in one direction only! Too much moisture may cause staining.
• Do not use benzene, paint thinner or alcohol!
1.2.17 Moving the product
• Make sure to switch off the product.
• Make sure to unplug all cables from the product.
• 2 people carry each edge. Screen showing upwards.
1.2.18 Disposal or handing over to a new owner
• It is recommended to initialize the unit by resetting it to factory's default.
• Do not mix with other general waste.
• Do not dispose the LCD display in waste treated by a waste treatment center.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
21
Page 26
1. Preliminary Remarks
1.2.19 Environmental information: disposal information
This symbol on the product indicates that, under the European Directive 2012/19/EU govern-
ing waste from electrical and electronic equipment, this product must not be disposed of with
other municipal waste. Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or
your municipal waste disposal service. For details, please visit the Barco website at:
http://www.barco.com/en/AboutBarco/weee
Disposal of batteries
This product contains batteries covered by the European Directive which must be collected and
disposed of separately from municipal waste.
If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium
(Cd), these chemical symbols will appear below the crossed-out wheeled bin symbol.
By participating in separate collection of batteries, you will help to ensure proper disposal and
to prevent potential negative effects on the environment and human health.
Turkey RoHS compliance
Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur
[Republic of Turkey: In conformity with the WEEE Regulation]
1.2.20 Exemptions
• This display is not liable for any damage caused by natural disaster (such as earthquake, thunder, etc.), fires,
acts by third parties, accidents, owner’s intentional misuse and fault, or uses in other improper conditions.
• This display is not liable for incidental damages (such as profit loss or interruption in business, modification
or erasure of record data, etc.) caused by use or inability to use of this product.
• This display is not liable for any damage caused by neglect of the instructions described in the owner’s man-
ual.
• This display is not liable for any damage caused by misuse or malfunction through simultaneous use of this
product and the connected equipment or software.
• This display is not liable for any damage caused by neglect of the instructions described about the installa-
tion stand in the owner’s manual.
• This display is not liable for any damage caused by improper installation.
22
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 27
1. Preliminary Remarks
1.2.21 Energy saving design
This device is designed to have computer equipment manufacturers build circuitry into their products to reduce
power consumption when it is not in operation. When this display is used with a PC on which a screen blanking
software complying with the VESA Display Power Management Signaling (DPMS) Protocol is installed, it can conserve significant energy by reducing power consumption when it is not in operation. There are 2 signal lines, 3
modes of operation. :On Mode, Sleep Mode, Off Mode.
On Mode The normal operation. When the display is on mode, being connected to a
power source, it displays an image.
Sleep Mode The reduced power state. returns to on mode when the user moves the mouse
or presses a key on the keyboard.
Off Mode The lowest power consumption state. returns to on mode when the user pushes a power
switch.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
23
Page 28
Page 29
2. Unpacking and installation
2 Unpacking and installation
2.1 Unpacking
The display is surrounded with foam for transportation protection and packed into a card box. Banding and fastening clips secure the package.
24 hours prior to installation/taking into operation the LCD displays have to acclimatize to
the room!
Do NOT open the bag during this time and keep the LCD displays in the card box. Only after
this period, lift the LCD displays out of the box.
To unpack the display,
• Release the fastening clips
• Remove the banding
• Open the Cardbox by lifting the upper cardbox part
• Remove the left and right upper foam.
• Take the display out
For later shipment, it is recommended to
store the original packaging and to re-use it.
Pour une expédition ultérieure, il est
recommandé de stocker l'emballage
d'origine et de le réutiliser.
The following components are included in the delivery:
• The display itself
• 1 pc CD (containing user manuals) / 1 pc Safety Manual
• 1 pc Infra red remote control unit and batteries
• 1 pc DP cable (1.8m)
• 1 pc IR Receiver
• 1 pc shipment return card
Do not use any pirated items to ensure the
safety and product life span.
Any damages or injuries by using pirated
items are not covered by the warranty.
Ne pas utiliser d'articles piratés pour
assurer la durée de la sécurité et durée de
vie du produit.
Les dommages ou blessures occasionnés en
utilisant des articles piratés ne sont pas
couverts par la garantie.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
25
Page 30
2. Unpacking and installation
2.2 Moving and handling the display
The display features two recesses on the rear side. When moving the display, always fetch it using these recesses, never touch the panel.
Be careful not to directly touch the panel or
expose it to shock when moving the display.
Veillez à ne pas toucher l’écran
directement ou l’exposer à des chocs lors
du déplacement de l’écran .
Make sure not to tilt the panel on the
bottom or on the edges: This will cause
severe damage!
In case you need to put the panel on the
floor, first place a cushion on the floor and
put the panel on it face looking down!
In case there is no cushion available, make
sure to have a clean and flat floor and place
the system face looking upwards. Take care
that no objects fall on the panel!
Assurez-vous de ne pas incliner l’écran sur
le bas ou sur les bords: Ceci causera des
dommages graves!
Dans le cas où vous avez besoin de mettre
l’écran sur le sol, placez d’abord un coussin
sur le sol et le mettre sur la face de l’écran
regardant vers le bas!
Dans le cas où il n'y a pas de coussin
disponible, assurez-vous d'avoir un sol
propre et plat et placer l’écran LCD
positionné ers le haut. Prenez soin de ne
pas laisser tomber des objets sur l’écran!
Put the display on the frame, never on
the panel!
If tilted on the panel, there will be severe damage on the bottom.
26
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 31
2. Unpacking and installation
If tilted on the edge, there will be severe damage on the edge!
Place a cushion on the floor; and put the
display, face down, on the cushion.
On a flat and clean surface, place the
panel face looking upwards.
2.3 Installation
Installation of the display shall comply with the safety instructions as listed in chapter 1.2.1 Safety on installation
• Make sure that the installation place has sufficient stability!
• Never restrict airflow into the display by blocking any vents or air intakes.
• Do not place the display near heat sources!
•
Do not install the product in a place with no ventilation (e.g. on a bookshelf).
• When fixing it to mounting plates, do not use screws longer than 16mm! Longer screws may damage the
display!
• Ensure that the display is operating within the specified operating range 0°C – 40°C | 32°F – 104°F, at max.
80% RH, non-condensing.
• Leave a clearance on all vented sides of the display to permit the required airflow.
Do not install the unit where it may be
easily touched or leaned against. Avoid
locations subject to high vibrations or severe
impacts. Do not install the unit where it is
exposed to humidity, oil, smoke or excessive
dust.
Ne pas installer l'unité où il peut être
touché ou sujet à d'éventuels chocs . Evitez
les endroits soumis à de fortes vibrations
ou des chocs violents. Ne pas installer
l'unité où il est exposé à l'humidité, l'huile,
la fumée ou poussière excessive.
For installation of the panels into a video
wall, please refer to the installation manual.
Pour l'installation de l’écran dans un mur
vidéo, veuillez consulter le manuel
d'installation.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
27
Page 32
2. Unpacking and installation
2.3.1 VESA compliant mounting solution
The displays can be mounted on a device that is compliant to the VESA MIS-F 600x400mm standard.
Attach the wall mounting bracket to the rear of the display.
Use the wall mount plate and screws that comply with the VESA standard.
Make sure that the wall mounting bracket is securely fixed to the display and to the wall. Do not over tighten the
screws as this may cause damage to the display set and void your warranty.
To attach the display to a device:
Attach the display firmly to the VESA compliant device using the screws included in the delivery!
Use a device that is approved by VESA
(according to the VESA MIL-F standard
600x400)
Use an arm that can support a weight of at
least 29.2kg or 64.4lbs.
Utilisez un dispositif qui soit approuvé par
VESA (En accordance à la norme VESA MIL-F
600x400)
Utilisez un bras qui peut supporter un
poids d'au moins 29.2kg or 64.4lbs.
2.3.2 Portrait mode
Turn the display clockwise (seen from front) when installing it in portrait mode.
28
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 33
2. Unpacking and installation
2.3.3 Dimensions of KVD5521 AND IVD5521:
2.3.3.1 Front view and side view
2.3.3.2 Rear view
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
29
Page 34
2. Unpacking and installation
2.3.4 Dimensions of HVD5521:
2.3.4.1 Front view and side view (without side seal)
Tolerance unspecified dimensions +/- 1mm
2.3.4.2 Rear view (including Side seal)
30
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 35
2. Unpacking and installation
2.4 Examining the display
2.4.1 Rear view
2.4.1.1 Mounting bolts
The display comes with 4 mounting bolts to allow connection to the front access mount and to the OB(L/P)X
structure. These mounting bolts are screwed in the VESA threads on the rear of the panel.
In case you go for a VESA mounting solution, please unscrew these mounting bolts.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
31
Page 36
2. Unpacking and installation
2.4.1.2 Inputs
On the rear, all interfaces are located as well as the exchangeable AC power module and the power connector.
The AC power module can be exchanged by a DC power adapter which allows connecting to the DC power supply
over distances to up to 100m without performance loss.
Safety instruction on opening systems built into a structure
OPS
OPS OPS Open pluggable specification channel with HDCP 1.4
DVI 1, DVI 2 DVI single link input with HDCP 1.4, up to 165 MHz)
HDMI HDMI 1.4a with HDCP 1.4, up to 300 MHz
DP DisplayPort input with HDCP 1.3, up to 300MHz
DP DisplayPort output with HDCP 1.4
S/PDIF Audio output interface according Sony/Philips Digital Interface specification
LAN 1, LAN 2 1 GB Ethernet input, video streaming supported.
USB USB interface USB 2.0
All inputs (OPS, DVI 1, DVI 2, HDMI, DisplayPort) have a loop-through connection to DisplayPort out (loop-through
connection is established as soon as the input is the active input).
The displays feature push buttons for some basic commands.
Currently 3 push buttons are supported: Power, Source, Menu
Power Press < 5sec to switch device from on to idle and vice versa (system with AC/DC Power supply)
Press > 5sec to bring the device to low power standby; when in low power standby, press <5sec to
start the display booting and showing the configured input source (system with AC/DC Power supply)
Menu Press <2sec to show the IP address of the device. Pressing it again goes back to last shown input
source.
Source Press <2sec to scroll the selected input to DVI1->DVI2->HDMI->DP->OPS->DVI1 …
32
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 37
3. Cabling
3 Cabling
All interfaces are located on the rear of the system!
3.1 Signal cabling
When connecting signals to the displays
please mind the bandwidth available with
the respective input:
DVI: 165 MHz
DisplayPort: 300 MHz
HDMI: 300MHz
Lors de la connexion des signaux aux écrans
tenez compte de la bande passante
disponible à l'entrée respective
DVI: 165 MHz
DisplayPort: 300 MHz
HDMI: 300MHz
Since the displays support scaling and cropping, and since the active input has a loop-through connection to the
DisplayPort, connecting displays in loop-through saves long signal cables and avoids guiding dozens of cables
from the display to the controller.
3.2 IR Remote Control cabling
The IR Loop through in daisy chain is not supported! Do not use the interface IR Loop but connect each display to
its dedicated IR receiver.
ed
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
33
Page 38
3. Cabling
3.3 Connecting devices
3.3.1 PC
An external PC / display wall controller can be connected via a DVI cable, a DisplayPort cable, or an HDMI connection.
Please note that the DVI interface is for
signals up to 165 MHz. In case higher
bandwidth is required, f.i. when
connecting displays in a loop-through
configuration use the DisplayPort
connection or the HDMI interface.
Veuillez noter que l'interface DVI est pour un
signal jusqu'à 165 MHz. Dans le cas où une
bande passante plus élevée est requise, par
exemple lors de la connexion d'écrans dans
une configuration en boucle utiliser la
connexion DisplayPort ou l'interface HDMI
Connect the cable and tighten it by turning the screws clockwise.
If you use an HDMI cable, first remove the screw!
Use a shielded signal interface cables with
a ferrite core to maintain standard
compliance for the product.
If applicable, use a High Speed HDMI™
Cable. High Speed HDMI™ Cables are tested
to carry an HD signal up to 1080p and
higher.
Utilisez des câbles d’interface blindés avec
noyau de ferrite pour maintenir une
conformité standard du produit.
Le cas échéant, utilisez un câble HDMI ™
haute vitesse. Les cables HDMI ™ haute
vitesse sont testés pour le transfert du
signal HD jusqu'à 1080p et supérieur
HDMI carries both, video and audio signals. Therefore in case your computer has HDMI output, there is no need
for an extra audio connection to the display. However you need to connect the S/PDIF audio out via a TOSLINK
cable with an AV receiver that can decode two channels of uncompressed lossless PCM audio or compressed
5.1/7.1 surround sound such as Dolby Digital Plus or DTS-HD High Resolution Audio
Unlike HDMI, TOSLINK does not have the
capacity to carry the lossless versions of
Dolby TrueHD and DTS-HD Master Audio
Contrairement à HDMI, TOSLINK n'a pas la
capacité de réaliser les versions sans perte
Dolby TrueHD et DTS-HD Master Audio
34
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 39
3. Cabling
The display has loop-through of the active input (OPS, DVI, HDMI, DisplayPort) to the DisplayPort out which allows connecting multiple sets of displays in a daisy chain.
If connected in a daisy chain, the signal of a PC can be displayed on all connected sets of displays. No signal splitter box is required.
To set up a daisy chain, proceed as follows:
Connect the PC to e.g. DisplayPort in of the first display.
Connect DisplayPort OUT of the first display to DisplayPort IN of the following display.
Proceed accordingly for all displays; always connect DisplayPort OUT of the previous display to DisplayPort IN of
the following display.
As soon as the input (OPS, DVI, HDMI,
DisplayPort) is selected the active input this
input has loop-through connection to the
DisplayPort output
Dès que l'entrée (OPS, DVI, HDMI, Display
Port) est sélectionnée comme entré
active, cette entrée à une connexion en
boucle à la sortie DisplayPort
The max. length of the cables is 3m!
In case you encounter decrease of image
quality when connecting multiple displays,
use an amplifier!
La longueur maximum des câbles est de
3 m!
Dans le cas où vous rencontrez une
diminution de la qualité de l'image lors
de la connexion d'écrans multiples,
utilisez un amplificateur!
3.3.2 LAN connection
The display features a LAN interface for network and/or internet connections.
Make sure to use cables with shielding of type
S-FTP or S-STP when connecting the display to
the network!
Assurez vous d'utiliser des câbles avec un
blindage de type S-FTP ou S-STP lors de la
connexion de l’écran au réseau!
The displays feature integrated processors that is ready to be enabled for future network streaming, cropping
and scaling, without the need for an external controller or player. Just connect the screens to the network, configure the settings and let the content play. This is extremely useful in basic control rooms where the full operation (e.g. camera surveillance) can now be done without a player or controller.
The streaming video needs to comply with RTP/UDP protocol and needs to be encoded as H.264 (up to
1080p@60fps, HiP (High Profile) 4:2:0, Level 4.2
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
35
Page 40
3. Cabling
3.3.3 Connecting to an HD receiver, DVD, Camcorder, Camera, Gaming Device or VCR player
An HD receiver, camcorder, camera, gaming device or VCR player is connected to the display using the HDMI IN
or Component IN interfaces.
Since the display does not feature an audio
IN interface, connecting HDMI sources via
an HDMI-DVI adapter will only transmit the
video; the audio included in the HDMI
signal will be lost.
Comme l'écran ne dispose pas d’interface
entrée son, la connexion de sources HDMI via
un adaptateur HDMI-DVI ne transmet que la
vidéo; l'audio inclus dans le signal HDMI sera
perdu.
3.4 Communication cabling
3.4.1 IR receiver
The display can be controlled via an IR Remote Control Unit which requires plugging in the IR receiver to the
display.
The IR receiver is connected to the rear of the system. It is plugged into the interface labeled IR-SENSOR.
If IR remote controlled is required, each display needs to be controlled separately!
36
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 41
3. Cabling
3.4.2 IR Remote Control
The batteries are not yet inserted in the remote control to avoid remote control operation in its package, resulting in a shorter battery lifetime.
How to install the batteries:
• Push the cover tab open
• Insert 2 batteries of type AAA, making sure the polarities match the + and – marks inside the battery com-
partment.
• Close the cover.
• If the remote is going to be unused for long periods of time, be sure to remove the batteries to prevent
leakage, which could damage the remote control.
• The liquid contents in the batteries is harmful to the skin; do not touch the leakage with your bare hands
directly. When installing fresh batteries, be sure to clean up the leakage thoroughly.
• If the range of effective remote control signal reception decreases or if the remote control stops working,
replace the batteries.
Do not mix old and new batteries, as this
may damage the remote control.
Ne pas mélanger piles neuves et
anciennes, cela pourrait endommager la
télécommande.
Note that there may be laws concerning
disposal and recycling of used batteries in
your country! Please contact your local
authorities to get further information!
Veuillez noter qu’il peut avoir des lois
relatives à l'élimination et le recyclage des
piles usagées dans votre pays! S'il vous
plaît contacter les autorités locales pour
obtenir de plus amples renseignements!
Avoid keeping used, old batteries inside the
remote control, causing leakage of internal
liquid resulting metal rust or fatal damage
to the remote control unit.
Evitez de garder les vieilles piles utilisées
dans la télécommande, causant la fuite du
liquide interne causant de la rouille au
métal ou des dommages fatals à la
télécommande.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
37
Page 42
3. Cabling
❶
: on/off
❷: Home / Menu
❸: OK OK
❹: arrow right
❺: arrow up
❻: arrow left
❼: arrow down
❽: LED indication
❾: Battery Compartment
❿: IR LEDs
38
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 43
3. Cabling
3.5 Power cabling
Check the power rating on your outlet
before connecting the display to the AC
inlet. Contact your facilities manager or a
qualified electrician if you are not sure
what type of power is supplied to your
building.
Vérifiez la puissance sur la prise avant de
brancher l'écran sur la prise secteur.
Contactez votre gestionnaire des
installations ou un électricien qualifié si
vous n'êtes pas sûr de ce type
d'alimentation est fourni dans votre
bâtiment.
The devices are designed to operate with
single-phase power systems having a
grounded neutral conductor. To reduce the
risk of electrical shock, do not plug into
any other type of power system.
Les dispositifs sont conçus pour fonctionner
avec les systèmes d'alimentation
monophasés avec conducteur neutre à la
terre. Pour réduire le risque de décharge
électrique, ne branchez pas sur un autre
type de système d'alimentation.
• Use the power cord which fulfill the specification listed in 1.2 Safety information
• Plug in the female power connector into the male connector AC IN on the rear of the display.
• Plug in the power cable to the wall outlet.
The power input is auto-ranging from 100VAC to 240 VAC.
3.5.1 Switching on and off
Connecting the display to the wall outlet will power on the display.
When the display is powered on, it can be switched into operation or switched to standby, respectively, using
the IR remote control unit (RCU).
If the system is not operated for longer
periods, it is recommended to disconnect it
from the wall outlet.
Si le système n’est pas utilisé pendant de
longues périodes, il est recommandé de le
débrancher de la prise murale.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
39
Page 44
3. Cabling
3.6 Installation of an OPS
The displays feature an OPS slot which conforms to the Intel standard. Make sure that the OPS you want to use
conforms to this standard as well!
For OPS, Barco recommends to use the Barco NGP-100.
On the back of the NGP-100 there is the JAE TX25 interface which needs to be connected to the OPS interface in
the display
Make sure to to plug in the OPS as shown in the picture below.
It is quite easy to plug it in the wrong way … and damage the OPS interface for good!
S
lide the OPS module into the OPS slot on the rear of the display and fix the two securing screws.
40
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 45
4. Design and function
4 Design and function
This chapter introduces the systems and explains some of their characteristics.
4.1 Display of choice
The displays are latest generation FullHD LCD displays with full matrix LED backlight.
The displays utilize a state-of-the-art IPS (in plane switching) LCD panel technology. This allows them being used
for an extended period of time without image sticking artifacts.
The displays are illuminated by a full matrix LED backlight: the white LEDs are positioned in an array behind the
screen.
The display features the following interfaces:
OPS
OPS OPS Open pluggable specification channel with HDCP 1.4
DVI 1, DVI 2 DVI single link input with HDCP 1.4, up to 165 MHz)
HDMI HDMI 1.4a with HDCP 1.4, up to 300 MHz
DP DisplayPort input with HDCP 1.3, up to 300MHz
DP DisplayPort output with HDCP 1.4
S/PDIF Audio output interface according Sony/Philips Digital Interface specification
LAN 1, LAN 2 1 GB Ethernet input, video streaming supported.
USB USB interface USB 2.0
All inputs (OPS, DVI 1, DVI 2, HDMI, DisplayPort) have a loop-through connection to DisplayPort out (loop-through
connection is established as soon as the input is the active input).
The state-of-the-art displays deliver crisp, clear images detailed to perfection and can be used in different professional applications.
The displays have a Web interface and can be addressed using any web browser in the subnet.
The display can be controlled via LAN using the BCM client application (Barco Wall Control Manager) or via API.
4.2 Cooling concept
The display features LED backlight.
LEDs like all semiconductors are quite sensitive to thermal stress and require a stable temperature for optimum
operation. Reliable heat dissipation is mandatory for a long lifetime.
As a rule of thumb lowering the temperature by 10°C will double product reliability.
Reliable heat dissipation is also mandatory stable intensity!
A temperature change of 10°C will shift the dominant wavelength of the emitted light of an LED up to 4nm (increasing temperature leads to shorter wavelengths).
Therfore the display has been provided with two cooling fans. The cooling of the electronics and the cooling of
the power supply is separated. This ensures a decoupling of the power section with the higher heat dissipation
versus the low power electronics for the logical controller.
Temperature is measured by sensors and continuously monitored by Barco Wall Control Manager which controls
the ultra low noise fans for optimal cooling.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
41
Page 46
4. Design and function
4.3 Option: EnergyStar compliance for the entire display wall
When switched to standby, power consumption of the display when operated via the integrated AC power supply
(delivery default) is less than 700mW.
To bring the entire display wall to the level of EnergyStar compliance, every display needs to be connected to the
power net via a so-called switch unit.
All switch units are controlled by the Green Green BCM which serves as both, as switch controller and as Barco
Wall Control Manager.
When switching the entire display wall on, the command is executed with minimal delays on all display: it is
only during the zero crossing that the display is switched on. Thus the inrush current of the entire display wall is
rather low and does not require special safeguarding.
When switched to standby, a display wall managed by the Green BCM will consume minimal power and the
entire display wall is energy efficient as defined by the standards of the US EPA.
The Version 6.0 ENERGY STAR Displays specification covers computer monitors, digital picture frames, and professional signage, collectively referred to as "displays" under this specification. ENERGY STAR certified displays must
consume 0.5 watts or less in Sleep Mode and On Mode power requirements vary according to screen area and
resolution.
The 700mW mentioned above are fully compliant with the ENERGY STAR requirements since the 0.2W on top are
due to the1GB Ethernet connection.
The switch units (2) and the Green BCM (1) are mounted to a DIN Rail. The picture shows the arrangement for a
display wall consisting of 4 displays.
One Green BCM can control up to 50 displays. One Green peut contrôler jusqu'à 50 écrans.
A switch button to control the entire nxm matrix of switch units and the Green BCM is also available as an option.
42
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 47
4. Design and function
4.4 Multiple sources, native resolution
In combination with a Barco display controller, KVD5521, IVD5521 and HVD5521 allow presenting sources in native resolution without loss of content, or scaled. Multiple sources (video, PC content or streaming video) can be
presented and positioned anywhere across the entire LCD wall.
4.5 Space saving
KVD5521, IVD5521 and HVD5521 video walls can be serviced from the front and the back. They require no back
room space at all, so they are ideally suited for control rooms where space is limited. The high resolution of the
tiled display wall allows operators sitting close by and displaying high-density information.
4.6 Front access
The unit has a smart, tiltable wall structure, which allows to easily servicing the display wall’s electronics and
cabling from the front. They require no back room space at all.
4.7 Barco Wall Control Manager (BCM)
An KVD/IVD/HVD video wall is controlled by Barco Wall Control Manager, a software package that continuously
supports worry-free operation of your video wall. No more surprises, no unplanned or distracting maintenance
interventions.
Wall configuration
The Barco Wall Control Manager supports operators in setting up the wall configuration.
Wall information
The Barco Wall Control Manager displays a wall dashboard showing all displays and their connection status.
Device information
The Barco Wall Control Manager displays a display dashboard showing wall position, operating state, serial number, runtime, temperatures, fans, MAC/IP address of a display.
Switching Inputs
The Barco Wall Control Manager allows switching the input to DVI1, DVI2, HDMI, DP, OPS.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
43
Page 48
4. Design and function
SenseX - Color and Brightness Calibration
KVD/IVD/HVD displays feature an integrated optical sensor. Color and brightness are monitored
To ensure good wall uniformity in terms of color and brightness levels, the displays come with Barco’s SenseX
automatic calibration system. This system works with a CIE colorimeter that continuously measures the primary
color levels of the display. The values are monitored and evaluated by the BCM. If required, i.e. if the display has
different values than the other displays in the wall, an adjustment process runs to ensure that the entire display
wall features an homogeneous color and brightness distribution.
4.8 Web interface
Connect to a display using its IP address and adjust the parameters of the display via the web interface.
44
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 49
5. Data processing
5 Data processing
Display walls used in control room environments usually receive their data from a video wall controller. Every
display is connected to one graphic channel and displays this data AS IS. In case scaling is required this usually
needs to be done by the graphical controller.
The KVD displays feature built in splitting and scaling functionality.
5.1 Scaling
The display mode (scaling parameter) can be set to actual size, keep aspect ratio, and fit to screen.
Setting Description
Actual Size show input resolution "As Is" (unscaled) on center of display resolution
Keep aspect ratio show input resolution scaled to display resolution, but keep aspect ratio: scaling factor
identical for horizontal and vertical pixels
Fit to Screen auto-scale input resolution to full display resolution: in case the aspect ratio of the
source differs from the aspect ratio of the display, the scaling factors for horizontal pixels and vertical pixels are not identical:
The default setting is fit to screen. Le réglage par défaut est Adapter à l’écran.
In case the aspect ratio of the source is equal the aspect ratio of the display, the settings "Fit to screen" and
"keep aspect ratio" have the same result.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
45
Page 50
5. Data processing
Aspect ratio of source: 4:3
Aspect ratio of display: 16:9
Top row, left module: Actual size (4 black borders):
Since the resolution of the display is greater than the resolution of the source, the image is displayed with black
borders.
Top row, right module: Keep aspect ratio:
The pixels of the source are up scaled to match the display resolution; the scaling factor in horizontal and in vertical direction is the same, the aspect ratio is preserved. But since the source has an aspect ratio 4:3, and the
display is 16:9, there are black borders on the left and on the right
Bottom row, left module: Fit to screen:
The pixels of the source are up scaled to match the display resolution; the scaling factors in horizontal and in
vertical direction are different, the image is distorted.
In case the aspect ratio of the source is equal
the aspect ratio of the display, the settings
"Fit to screen" and "Keep aspect ratio"have
the same result.
Dans le cas où le rapport d'aspect de la
source est égal au rapport d'aspect de
l'écran, les paramètres "Adapter à l'écran"
et "Conserver les proportions" ont le même
résultat.
46
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 51
5. Data processing
5.2 Loop-through, scaling, and splitting
The active input (OPS, DVI, DisplayPort, HDMI) has loop-through to the DisplayPort output.
A source connected to DisplayPort IN (DP IN) of any display can be shown on multiple displays The DisplayPort
OUT (DP OUT) of the previous display has to be connected to the DP IN of the following display, see schematics.
5.2.1 No scaling and no splitting
In this mode all displays show the entire source. The display mode can be Actual size, Fit to screen, or Keep
aspect ratio.
Loop-through of a source, group dimension 1x1 (=splitting off), display mode set to Actual size ( = scaling off)
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
47
Page 52
5. Data processing
5.2.2 Splitting and scaling
In these modes every display shows a part of the source. Which part of the pixels has to be displayed by which
display is defined via the group dimension (the area the source has to be displayed) and the position of the
display in this group.
The position of the display within the group
is independent from its order in the chain,
i.e. the cabling!
The position of the display in the group is
defined by its horizontal (column) and
vertical (row) position, not with reference to
the display wall, but to the group.
This setting is done in the web interface of
Green BCM
La position de l'affichage au sein du
groupe est indépendante de sa position
dans la chaîne, c'est à dire le câblage!
La position de l'écran dans le groupe est
définie par l’horizontale (colonne) et la
position verticale (en ligne), et non par
rapport au mur d’image, mais du groupe.
Ce réglage se fait dans l'interface web du
Green BCM
The display mode can be Actual size, Fit to screen, or Keep aspect ratio. The setting refers to the group!
Loop through of a source, group dimension 1x1 (= splitting off), display mode set to Fit to screen (= scaling on,
the pixels of the source are up scaled to match the display resolution).
48
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 53
5. Data processing
Loop through of a source, group dimension 2x2, (= splitting on, (on every display only a part of the source is
rendered), display mode set to Actual size ( = scaling off).
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
49
Page 54
5. Data processing
Loop through of a source, group size 2x2, (= splitting on (on every display only a part of the source is rendered)
display mode set to Fit to screen ( = scaling on).
5.3 Summary
The inputs with loop-through to DP OUT combined with the scaling and splitting functionalities offer a variety of
user scenarios to display a source. The DDC files required for such scenarios are provided on the web interface of
the display.
50
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 55
6. SenseX
6 SenseX
SenseX is Barco's unique sensor technology which provides brightness and color stability over time and across
the entire display wall.
An advanced color sensor measures the primary colors and feeds the values back to the color correction. Thus
brightness and color distribution is constant over time.
The system actively measures in the background and compensates for any changes of color and brightness. The
update cycle can be scheduled on a daily basis.
6.1 Theory
The concept of color can be divided into two parts: brightness and chromaticity.
In the CIE XYZ color space chromaticity of a color is specified by x and y.
The "horse shoe-shape" visualizes all colors.
The range of colors that can be reproduced with a given color reproduction system lies within this horse-shoe
shape.
Usually Red, Green, and Blue are selected colors placed at the corner (R, G, B). These colors are called primaries.
The triangle is called the gamut and represents all the colors of the respective system.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
51
Page 56
6.2 Principle of color locking and brightness locking
Due to aging effects and drifts the color location changes over time. To keep color constant, this drift has to be
measured and compensated (color lock).
Also brightness decreases due to aging. To keep brightness constant, the change in brightness has to be measured and compensated (brightness lock).
52
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 57
6. SenseX
6.3 Color sensor (colorimeter)
The sensor measures the color locations of red, green, and blue. The values of all displays are evaluated to find a
common brightness and color target.
6.4 Color & Brightness Modes
Color and brightness uniformity is a big challenge for display walls. Due to tolerances, every display has its own
brightness and color spectrum.
Barco's unique SenseX compensates for the differences of individual displays and results in a display wall with a
common brightness and color distribution constant over time.
A display wall can be operated in SenseX or Native mode.
6.4.1 Native
Calibration is done in the factory. Leaving production, all displays are set to native mode. Gain of the primaries as
well as black level and white level can be adjusted.
6.4.2 SenseX
SenseX locks the displays of a display wall to a common brightness and color location constant over time and
across the entire display wall.
An advanced color sensor measures color and brightness to detect spectral shift and feeds the values back to the
color correction.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
53
Page 58
Page 59
7. Web interface
7 Web interface
The displays feature a web interface for controlling and monitoring.
To access the web interface and to address a display, proceed as follows:
Connect the LAN 1 interface of the display to a PC/laptop.
On the PC/laptop, launch a web browser.
In its address bar, enter the IP address of the LAN1 interface:
Http://192.168.10.2
(The PC/laptop the web browser is running on needs to be in the same subnet as the display. Assign the
PC/Laptop a static IP address.
The display has two network interfaces, LAN1 and LAN2.
These are the default IP addresses:
LAN 1: 192.168.10.2
LAN 2: 192.168.12.2
Basically you can connect to either of the interfaces. It might be useful to decide on a clear
strategy how to use the interfaces, e.g. LAN1 for communication with the display, LAN2 for
future use.
The display’s landing page opens:
The web interface is explained in the reference manual web interface OVD/KVD/IVD.
.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
55
Page 60
Page 61
8. Barco Wall Control Manager (BCM)
8 Barco Wall Control Manager (BCM)
8.1 General
Barco Wall Control Manager software is a server/client application to manage and control Barco large display
walls.
The server runs on dedicated hardware, the Green BCM. The Green BCM is a wall router and the gateway to open
or download the client application.
The Green BCM can be accessed via its web interface.
Use the BCM client application to create a disply wall, assign devices to the wall, switch the device/the entire
wall to on/idle and check/switch the active input.
The main task of BCM application however is providing brightness and contrast settings and running the SenseXcolor adjustment algorithm.
8.2 Cabling
The displays are setup in a dedicated network, the wall net. Each display is connected to a wall switch via a LAN
cable.
Make sure to use cables with shielding of
type S-FTP or S-STP when connecting the
display to the network!
Assurez vous d'utiliser des câbles avec un
blindage de type S-FTP ou S-STP lors de la
connexion de l’écran au réseau!
LAN1 of the display is connected to the WALL interface of the Green BCM Box! This is the
only supported configuration!
A display MUST NOT be connected via LAN1 to WALL interface of Green BCM Box and via
LAN2 to CLIENT interface of Green BCM Box!
A display MUST NOT be connected via LAN1 to WALL interface of one Green BCM Box and
via LAN2 to WALL interface of a second Green BCM Box!
In case you think of additional ways of connecting a display be aware that these are NOT
supported!
The LAN switch is connected to the interface labelled WALL on the Green BCM device.
The network configuration of the CLIENT interface allows integrating the Green BCM into the customer network
thus allowing any PC/Laptop/workstation in the customer network to connect to the Green BCM and to run the
BCM client application to monitor and control the displays.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
57
Page 62
The BCM client is launched from the Green BCM web page. When clicking the link, expect the BCM landing page
to open.
58
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 63
8. Barco Wall Control Manager (BCM)
In case no wall has been defined yet the landing page just shows the navigation bar. Click
SETUP to create a wall.
The Green BCM web interface and the BCM client is explained in the user manual BCM for OVD/KVD/IVD.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
59
Page 64
Page 65
9. Maintenance and servicing
9 Maintenance and servicing
Only authorized personnel should carry out
other maintenance work not explicitly
mentioned in this manual!
Never open the case of the display without
first disconnecting the power supply cord!
Measurements and tests with the opened
device may be carried out only in the factory
or by specially trained personnel, due to the
dangers of electrical shock.
Quand un écran qui est intégré dans une
structure doit être démonté, au préalable
démontez tous les écrans au-dessus de
celui que vous devez désinstaller puis
fermez les interfaces: Cela vous donne
libre accès à l'écran que vous souhaitez
enlever et élimine le risque
d'endommager l'écran suspendu audessus lors du déplacement vertical du
système!
When doing maintenance work or changing
cables on a display built into a structure you
have to open all displays ABOVE the one you
want to work on.
Lors de l'ouverture d'un écran qui est
intégré dans une structure, appuyez
simultanément sur les côtés inférieurs
droit et gauche de l’écran (il existe des
loquets derrière).
Dans le cas où le cadre de l'interface ne
s’ouvre pas, très probablement vous
faites face à une situation mixte de
loquets; un ouvert, un fermé. Alors
pressez sur celui de gauche ou de droite,
ou mettez les loquets dans la même
position.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
61
Page 66
When a display which is built into a
structure has to be de-mounted, first demount all displays above the one you have
to de-install and then close the interfaces:
This gives you free access to the display
you want to remove and eliminates the
risk of damaging the display hanging
above when moving the system up!
Quand un écran qui est intégré dans une
structure doit être démonté, au préalable
démontez tous les écrans au-dessus de celui
que vous devez désinstaller puis fermez les
interfaces: Cela vous donne libre accès à
l'écran que vous souhaitez enlever et
élimine le risque d'endommager l'écran
suspendu au-dessus lors du déplacement
vertical du système!
When opening a display which is built into
a structure, simultaneously press on the
left and right bottom sides of the displays
(there are the latches behind).
In case the interface frame does not open
you very probably have a mixed situation
of latches; one is opened, one closed. Then
only press on the left OR on the right ot
make the position of the latches the same.
Lors de l'ouverture d'un écran qui est intégré
dans une structure, appuyez simultanément
sur les côtés inférieurs droit et gauche de
l’écran (il existe des loquets derrière).
Dans le cas où le cadre de l'interface ne
s’ouvre pas, très probablement vous faites
face à une situation mixte de loquets; un
ouvert, un fermé. Alors pressez sur celui de
gauche ou de droite, ou mettez les loquets
dans la même position..
62
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 67
9. Maintenance and servicing
9.1 Cleaning
Power plug
If dust has collected on the power plug connectors, remove the plug from the outlet and clean off the dust. This
dust may cause a fire due to reduced insulation of the plug.
Cabinet
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning. To keep the cabinet looking brand-new, periodically clean it with a soft cloth. Stubborn
stains may be removed with a cloth lightly dampened with mild detergent solution. Never use strong solvents,
such as thinner or benzene, or abrasive cleaners, since these will damage the cabinet.
Contamination of screen surface.
When the screen surface of the display is contaminated, please wipe the surface softly with cotton swab or clean
cloth. If it is not enough, please take it away with cellophane tape or wipe the surface with damp cotton swab or
clean cloth. In this case, please be careful so that the water does not get in inside of the LCD module, because it
may be damaged.
Water drop on LCD surface
Please do not leave LCD module with water drop. When the display surface gets water drop, please wipe it off
with cotton swab or soft cloth immediately, otherwise display surface will be deteriorated. If water gets in inside
the LCD module, the electric circuits may be damaged.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
63
Page 68
Page 69
10. Technical data
10 Technical data
10.1 Display capabilities
Panel technology S-IPS
Screen Type 1387.8 mm wide (55 inch) TFT (Thin Film Transistor) LCD (Liquid
Crystal Display) Panel
Pixel pitch 0.630 mm (H) x 0.630 mm (V)
Resolution Full HD 1920 x 1080 pixels
Backlight Direct LED
Aspect ratio 16:9
Pixel density 40 dpi
Refresh rate 60 Hz
Viewing angle H 178°| V 178°
Luminance in Spec: 350±10% cd/m2 at backlight setting 50 (normal)
Luminance of white KVD 500cd/m2 (Typ)
Luminance of white IVD 700cd/m2 (Typ)
Contrast ratio KVD 1,000:1(Min) , 1,400:1 (Typ.)
Contrast ratio IVD 800:1 (Mn), 1200:1 (Typ)
Native white point 10,000 K
Color depth 10 bits – 1.06 B colors
Color coordinates (typ.) Red: Rx = 0.647 Ry = 0.334
Green Gx = 0.304 Gy = 0.602
Blue Bx = 0.152 By = 0.059
White Wx = 0.279 Wy = 0.292
Response time gray to gray (typ.) 8 ms (typ)
10.2 Operating performance
Backlight operating life time
60,000 h (Typ.) | Min. 50,000h (the time to take until the bright-
ness reduces to 50% of its original value)
MTBF pa
nels 50,000 h |
MTBF electronics
90,000 h
10.3 Mechanical KVD5521 AND IVD5521
Active screen diagonal
1387.8 mm | 55 in.
Dimensions
(+/- 1.3mm) (L)1213.4 x (W) 684.2 x(T) 98.3 | 47.77” x 26.94” x 3.87”
Active screen area
1209.6 (H) x 680.4 (V) | 47.62” x 26.79”
Bezel width
(+2.6mm / -1.3mm) Right, bottom: 1.2 mm | 0.047”
Left, top: 2.3 mm | 0.091”
Weight
29.8 kgs (net) | 65.7 lbs (net)
Cooling
Low noise fans
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
65
Page 70
10.4 Mechanical HVD5521
Active screen diagonal
1388 mm | 55 in.
Dimensions
(+/- 1.3mm) (L)1211.4 x (W) 682.2 x(T) 102 | 47.69” x 26.85” x 4.015”
Active screen area
1209.6 (H) x 680.4 (V) | 47.62” x 26.79”
Bezel width
(+0.9mm / +0.5/-0) Right, bottom: 0.9 mm | 0.035”
Left, top: 0.9 mm | 0.035”
Weight
20.8 kgs (net) | 45.85 lbs (net)
Cooling
Low noise fans
10.5 Power
AC input voltage 100-240 VAC, 60/50Hz
Power consumption KVD
(Max|Normal|Smart Energy Saving|DPMS
Off|Power Off)
400W |180W | 120W | 1.0W (RGB)/1.0W HDMI | 0.7W
Power consumption IVD
(Max|Normal|Smart Energy Saving|DPMS
Off|Power Off)
400W |190W | 120W |1.0W (RGB)/1.0W HDMI | 0.5W
Power consumption HVD
(Max|Normal|Smart Energy Saving|DPMS
Off|Power Off)
400W |180W | 120W |1.0W (RGB)/1.0W HDMI | 0.5W
typ heat dissipation (BTU/h) KVD 615 (without OPS) (@180W)
typ heat dissipation (BTU/h) IVD 648 (without OPS) (@190W)
typ heat dissipation (BTU/h) HVD 615 (without OPS) (@1800W)
max heat dissipation (BTU/h) KVD, IVD,
HVD
1365 (without OPS) (@400W)
10.6 Signal connectors and supported resolutions
2 x DVI Single link DVI-D in/out
HDMI HDMI 1.4a Type A with HDCP
DP Display Port 1.1 Input
OPS 1x OPS Slot
10.7 Wall control
Barco Wall control manag
er
Server connected via RJ45;
displays connected via RJ45.
Remote client application: on/off, wall setup, source selection, status, brightness,
contrast and color adjustments
Control signal RJ-45 Ethernet star architecture.
66
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 71
10. Technical data
10.8 Environmental and regulation compliance
Operational Temperature: 0-40°C
Humidity: 10-80% non-condensing (KVD, IVD)
Humidity: 10-90% non-condensing (HVD)
Dust: ISO 14644-1 ISO class 8
Storage Temperature: -20-60°C
Humidity: 5-95% non-condensing (KVD, IVD)
Humidity: 10-90% non-condensing (HVD)
Acclimatization
before installation
24 hours
Safety UL/c-UL/CB/TUV/KCC
EMC FCC/CE/KC
Erp Yes
ENERGY STAR 6 KVD: Yes / IVD: no / HVD: no
10.9 Light Leakage KVD/IVD
Light leakage along the bezel is a typical, technology caused, phenomenon of LC Displays with very narrow bezel.
In order to provide best in class products to its customer BARCO has defined very strict limitation to the amount
of light leakage that can affect a BARCO product
By this the visual effect for the customer is limited or nil.
We only accept very minor light leakage as defined by the below limitations:
Standing 0.5 meter away from the panel and moving backward along a Z axis up to 1.5 meter, the Z axis must
be perpendicular to the panel and start from its centre.
• Less than 10 mm of consecutive light visible on the bezel
• Less than 3 pieces of light (total less than 10mm) from long side with every piece more than 50mm far from
the others
• Less than 2 pieces of light (total less than 10mm) from short side
10.10 Light Leakage HVD
Related to new Bezel technology there is no Light Leakage as known before existing anymore.
But caused by the extreme narrow bezel it happens that light is reflected on the pcbs connected to the sides of
the LC. This can appear in a copper/brownish reflection.
Between these reflections a smaller bluish reflection can be visible.
These effects are not visible anymore from a distance of 3m from the panel at a point perpendicular to the center of the panel.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
67
Page 72
10.11 Cosmetic specification
10.11.1 Inspection conditions
Ambient illumination 300-700 Lux
Ambient temperature 20 - 25°C
Ambient humidity 65 ± 5 %
Viewing distance minimum 4x height of panel
One display pixel contains three subpixels or dots (red, green, and blue).
10.11.2 Definition of dot defect
If the luminance of a dot is brighter or darker than the surrounding dots, this is called a dot defect.
Bright dot Dots (subpixels) which appear brightly in the screen when displaying a dark pattern
Dark dot Dots (subpixelx) which appear darkly in the screen when displaying a bright pattern
Dots smaller than half a subpixel are not counted as defect dots.
The dot defect is inspected on red, green, blue, white or black pattern.
Defects which are outside the active area are not considered as defect.
Dot Defect Type
Max
Bright dot Random 3
Adjacent 2 dots 1
Dark dot Random 7
Off dot Random 10
Adjacent 2 dots 2
Adjacent 3 dots 1
Total amount of dots 15
Minimum distance between defects Bright dot - bright dot 5 mm
Dark dot - dark dot Ignore
10.11.3 Dot classification method
The criteria of dot is defined by its brightness as below:
Comparison of brightly visible dot with background
• Step 1
Detect bright dots at 0% gray level (black background). If any dots are visible, go to 25% gray level.
• Step 2
At 25% gray level:
- If the dot is no longer visible, it does not count;
68
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 73
10. Technical data
- If the dot is still visible and bright:
- For R or B dot, go to 50% gray level;
- For G dot, go to 30% gray level;
• Step 3
- If the dot is still visible (G at 30% gray level, R or B at 50% gray level) it counts as a bright dot;
- Otherwise it counts as a dark dot.
• Step 4
A dot that is identifiable at 100% white background as a dark dot (R, G, and B) counts as an OFF dot.
10.11.4 Definition of uniformity defect
While operating the LCD panel, if a certain area is remarkably brighter or darker, this is considered a uniformity
defect.
However, extraneous substances which can be wiped off like fingerprints or particles are not considered a uniformity defect.
10.11.5 Spot and linear type inspection
Defect Type Criteria
Max
Spot defect 0.1 < D <= 3.0 (mm)
5
Linear defect
0.01 < W <= 0.4 (mm)
5
2 < L <= 15.0 (mm)
Total amount of defects
10
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
69
Page 74
Page 75
11. Interfaces
11 Interfaces
11.1 DVI-D, single link
C5
Analog Ground (analog
R, G, & B return)
8
Analog VSync
16
Hot Plug Detect
24
TMDS Clock-
7 DDC Data 15
Ground (return for +5V,
Hsync, and Vsync)
23 TMDS Clock+
6
DDC Clock
14
+5V
22
TMDS Clock Shield
5
TMDS Data4+
13
TMDS Data3+
21
TMDS Data5+
4
Not connected
12
Not connected
20
Not connected
3
TMDS Data2, 4 shield
11
TMDS Data1, 3 shield
19
TMDS Data0, 5 shield
2
TMDS Data2+
10
TMDS Data1+
18
TMDS Data0+
1
TMDS Data2-
9
TMDS Data1-
17
TMDS Data0-
11.2 HDMI Type A
2
4
6
8
10
12
14
16
18
1
5
9
13
17
3
711
15
19
Pin
signal assignment
pin
signal assignment
1 TMDS Data 2+
11 TDMS Clock Shield
2 TMDS Data Shield
12 TDMS Clock -
3 TMDS Data 2-
13 CEC
4 TMDS Data 1+ 14 Reserved
5
TMDS Data Shield
15
Clock
6 TMDS Data 1-
16 Data
7 TMDS Data 0+
17 DDC/CEC Ground
8 TMDS Data 0 Shield 18 +5 V Power
9 TMDS Data 0-
19 Hot Plug Detect
10 TMDS Clock +
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
71
Page 76
11.3 DisplayPort
1
DP Lane 3-
2
DP Lane 3 Shield
3
DP Lane 3+
4
DP Lane 2-
5
DP Lane 2 Shield
6
DP Lane 2+
7
DP Lane 1-
8
DP Lane 1 Shield
9
DP Lane 1+
10
DP Lane 0-
11
DP Lane 0 Shield
12
DP Lane 0+
13
DP Config 1
14
DP Config 2
15
DP AUX +
16
DP AUX Shield
17
DP AUX -
18
DP Hot Plug Detect
19
GND
20
DP Power 3.3V
11.4 S/PDIF connector (TOSLINK)
1
Ground
2
Current limit resistance
3
VCC
4
Input SPDIF Signal
5
Not Connected
6
Not Connected
72
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 77
11. Interfaces
11.5 USB connector
1
+5V power
2
Differential Data line
3
Differential Data line
4
GND
11.6 OPSconnector
The standard 80 pin connector carries following signals:
• 1 HDMI interface with pixel clock up-to 300MHz
• +12V Power (Output) to the Pluggable Module.
• 1 USB 2.0 differential Signals
• 1 UART interface
• Power Status Signal (Input) Power Good status of the pluggable board
• Pluggable Signal On(output) To Power ON or boot up the Pluggable Module
• Pluggable board detection (Input) signal
Pin No.
Signal
Description
I/O 1 DDP_3N
DisplayPort (NC)
IN 2 DDP_3P
DisplayPort (NC)
IN 3 GND
Ground
4 DDP_2N
DisplayPort (NC)
IN 5 DDP_2P
DisplayPort (NC)
IN 6 GND
Ground
7 DDP_1N
DisplayPort (NC)
IN 8 DDP_1P
DisplayPort (NC)
IN 9 GND
Ground
10
DDP_0N
DisplayPort (NC)
IN
11
DDP_0P
DisplayPort (NC)
IN
12
GND
Ground
13
DDP_AUXN
DisplayPort (NC)
I/O
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
73
Page 78
14
DDP_AUXP
DisplayPort (NC)
I/O
15
DDP_HPD
DisplayPort (NC)
OUT
16
GND
Ground
17
OPS_TMDS_CLK-
DVI-D
IN
18
OPS_TMDS_CLK+
DVI-D
IN
19
GND
Ground
20
OPS_TMDS_RX0-
DVI-D
IN
21
OPS_TMDS_Rx0+
DVI-D
IN
22
GND
Ground
23
OPS_TMDS_RX1-
DVI-D
IN
24
OPS_TMDS_RX1+
DVI-D
IN
25
GND
Ground
26
OPS_TMDS_RX2-
DVI-D
IN
27
OPS_TMDS_RX2+
DVI-D
IN
28
GND
Ground
29
OPS_SDA
DVI-D
I/O
30
OPS_SCL
DVI-D
I/O
31
OPS_HPD
DVI-D
OUT
32
GND
Ground
33
P12V
Power
34
P12V
Power
35
P12V
Power
36
P12V
Power
37
P12V
Power
38
P12V
Power
39
P12V
Power
40
P12V
Power
41
RSVD
Reserved pins
42
RSVD
Reserved pins
43
RSVD
Reserved pins
44
RSVD
Reserved pins
45
RSVD
Reserved pins
46
RSVD
Reserved pins
47
RSVD
Reserved pins
48
RSVD
Reserved pins
49
RSVD
Reserved pins
50
SYS_FAN
System Fan Control
IN
51
UART_RXD
UART 3.3V
OUT
52
UART_TXD
UART 3.3V
IN
53
GND
Ground
54
NC
55
NC
56
GND
Ground
57
NC
58
NC
59
GND
Ground
60
NC
61
NC
62
GND
Ground
63
NC
64
NC
65
GND
Ground
66
USB_PN0
USB
I/O 25
67
USB_PP0
USB
I/O 26
68
GND
Ground
69
AZ_LINEOUT_L
Audio-Left channel
IN
70
AZ_LINEOUT_R
Audio-Right channel
IN
74
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 79
11. Interfaces
71
OPS_CEC
Consumer Electronic Control
I/O
72
PB_DET
Pluggable Board Detect
IN
73
PS_ON#
Pluggable Signal ON
OUT
74
PWR_STATUS
PowerGood
IN
75
GND
Ground
76
GND
Ground
77
GND
Ground
78
GND
Ground
79
GND
Ground
80
GND
Ground
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
75
Page 80
Page 81
12. DDC Files programmed in the display
12 DDC Files programmed in the display
12.1 DisplayPort
Description in web interface
Layout
Pixel
Frequency
Timing
NTSC, 60Hz, 1080p (default)
1x1 1920x108
0
59.94
ddc_1920_1080_59940
NTSC, 60Hz, 1080p, 1 by 2
1x2 1920x2160
59.94
ddc_1920_2160_59940
NTSC, 60Hz, 1080p, 2 by 1
2x1 3840x1080
59.94
ddc_3840_1080_59940
NTSC, 30Hz, 1080p, 1 by 2
1x2 1920x2160
29.97
ddc_1920_2160_29970
NTSC, 30Hz, 1080p, 2 by 1
2x1 3840x1080
29.97
ddc_3840_1080_29970
NTSC, 30Hz, 1080p, 2 by 2
2x2 3840x2160
29.97
ddc_3840_2160_29970
NTSC, 30Hz, 1080p, 1 by 3
1x3 1920x3240
29.97
ddc_1920_3240_29970
PAL, 50Hz, 1080p
1x1 1920x1080
50 ddc_1920_1080_50000
PAL, 50Hz, 1080p, 1 by 2
1
x2
1920x2160
50 ddc_1920_2160_50000
PAL, 50Hz, 1080p, 2 by 1
2x1 3840x1080
50 ddc_3840_1080_50000
PAL, 25Hz, 1080p, 1 by 2
1x2 1920x2160
25 ddc_1920_2160_25000
PAL, 25Hz, 1080p, 2 by 1
2x1 3840x1080
25 ddc_3840_1080_25000
PAL, 25Hz, 1080p, 2 by 2
2x2 3
840x2160
25 ddc_3840_2160_25000
PAL, 25Hz, 1080p, 1 by 3
1x3 1920x3240
25 ddc_1920_3240_25000
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
77
Page 82
12.2 HDMI
Description in web interface
Layout
Pixel
Frequency
Timing
NTSC, 60Hz, 1080p (default)
1x1 1920x1080
59.94
ddc_1920_1080_59940
NTSC, 60Hz, 1080p, 1
by 2
1x2 1920x2160
59.94
ddc_1920_2160_59940
NTSC, 60Hz, 1080p, 2 by 1
2x1 3840x1080
59.94
ddc_3840_1080_59940
NTSC, 30Hz, 1080p, 1 by 2
1x2 1920x2160
29.97
ddc_1920_2160_29970
NTSC, 30Hz, 1080p, 2 by 1
2x1 3840x1080
29.97
ddc_3840_1080_29970
NTSC, 30H
z, 1080p, 2 by 2
2x2 3840x2160
29.97
ddc_3840_2160_29970
NTSC, 30Hz, 1080p, 1 by 3
1x3 1920x3240
29.97
ddc_1920_3240_29970
PAL, 50Hz, 1080p
1x1 1920x1080
50 ddc_1920_1080_50000
PAL, 50Hz, 1080p, 1 by 2
1x2 1920x2160
50 ddc_1920_2160_50000
PAL, 50Hz, 10
80p, 2 by 1
2x1 3840x1080
50 ddc_3840_1080_50000
PAL, 25Hz, 1080p, 1 by 2
1x2 1920x2160
25 ddc_1920_2160_25000
PAL, 25Hz, 1080p, 2 by 1
2x1 3840x1080
25 ddc_3840_1080_25000
PAL, 25Hz, 1080p, 2 by 2
2x2 3840x2160
25 ddc_3840_2160_25000
PAL, 25Hz, 1080p,
1 by 3
1x3 1920x3240
25 ddc_1920_3240_25000
78
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 83
12. DDC Files programmed in the display
12.3 DVI
Description in web interface
Layout
Pixel
Frequency
Timing
NTSC, 60Hz, 1080p (default)
1x1 1920x1080
59.94
ddc_1920_1080_59940
NTSC, 60Huz, 1080p (TFA)
1x1 1920x1080
60.5 ddc_1920_1080_60500
NTSC, 30
Hz, 1080p, 1 by 2
1x2 1920x2160
29.97
ddc_1920_2160_29970
NTSC, 30Hz, 1080p, 2 by 1
2x1 3840x1080
29.97
ddc_3840_1080_29970
PAL, 50Hz, 1080p
1x1 1920x1080
50 ddc_1920_1080_50000
PAL, 50Hz, 1080p (TFA)
1x1 1920x1080
50.5 ddc_1920_1080_50500
PAL, 25Hz, 1
080p, 1 by 2
1x2 1920x2160
25 ddc_1920_2160_25000
PAL, 25Hz, 1080p, 2 by 1
2x1 3840x1080
25 ddc_3840_1080_25000
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
79
Page 84
Page 85
13. Troubleshooting
13 Troubleshooting
When faults occur which are not described below please contact Barco.
13.1 Faults
Faults cause/steps
No picture Make sure that the power cord is plugged into the wall out
let.
Make sure that the display is not in off
Check if the signal cables are properly connected to the display and to the signal source
Check if the input setting is correct
Check if the signal is suitable.
The display can not be controlled via the
IR RCU
Make sure that the batteries are inserted correctly (matching
the + and – marks of the battery compartment)
Replace the batteries.
Point the front of the RCU directly to the sensor.
Is the senor properly connected?
The remote control unit will not function properly if strong
light strikes the sensor window or if there are obstacles between the remote control unit and the IR sensor.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
81
Page 86
13.2 Contact
Feel free to contact us if you have any further questions!
BARCO N.V. - Europe
Beneluxpark 21, 8500 Kortrijk (Belgium)
RPR Kortrijk - BE0473191041
Visit Barco at http://www.barco.com
For Professional Support visit
http://www.barco.com/support
For Sales or other Contact information visit
http://www.barco.com/contact/regional-offices
82
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 87
14. Compliance statement
14 Compliance statement
14.1 FCC Compliance statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However there is no
guarantee that interferences will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception (which can be determined by
turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not
expressly approved by the party responsible
for compliance could void the user's (or
your) authority to operate the equipment.
Only peripherals (digital input/output
devices, terminals, printers, etc.) certified to
comply with the Class B limits may be
attached to this display. Operation with noncertified peripherals is likely to result in
interference to radio and TV reception. Only
shielded signal cables may be used with this
System.
Attention: Des changements ou modifications non expressément approuvés par la
partie responsable de la conformité pourraient annuler l'autorité de l'utilisateur ou
la votre pour utiliser l'équipement. Seuls
les périphériques (entrée numérique / périphériques de sortie, terminaux, imprimantes, etc) certifiés comme étant conformes aux limites de la classe B peuvent
être connectés à cet écran. L'utilisation de
périphériques non conformes peut provoquer des interférences dans la réception
radio et télévision. Seuls des câbles blindés
peuvent être utilisés avec ce système
The regulations are applied only to the
products with the ID LABEL indicating specific
requirements.
Les règlements sont appliqués que pour les
produits avec l'étiquette d'identification
indiquant les besoins spécifiques
14.1.1 Declaration of Conformity
Trade name: KVD5521, IVD5521, HVD5521
Responsible Party: Barco, Inc
3059 Premiere Parkway
Suite 400
30097 Duluth, Georgia, USA
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
83
Page 88
14.2 Canadian DOC Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
The regulations are applied only to the
products with the ID LABEL indicating specific
requirements.
Les règlements sont appliqués que pour les
produits avec l'étiquette d'identification
indiquant les besoins spécifiques
84
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 89
14. Compliance statement
14.3 Chinese Mainland RoHS
中国大陆 RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》（也称为中国大陆 RoHS）， 以下部分列出了
Barco 产品中可能包含的有毒和/或有害物质的名称和含量。中国大陆 RoHS 指令包含在中国信息产业部 MCV
标准：“电子信息产品中有毒物质的限量要求”中。
According to the “Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and
Electronic Products” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of
toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in
the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of toxic
substances in Electronic Information Products”.
零件项目(名称)
Component Name
有毒有害物质或元素
Hazardous Substances or Elements
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
印制电路配件
Printed Circuit Assemblies
X O O O O
O
液晶面板
LCD Panel
X O O O O
O
外接电(线)缆
External Cables
X O O O O
O
底架
Chassis
X O O O O
O
印制电路配件
Printed Circuit Assemblies
X O O O O
O
印制电路主要配件
Main Printed Circuit Assembly
X O O O O
O
插入式插件
Plug assembly
X O O O O
O
內部线路
Internal wiring
X O O O O
O
本表格依据 SJ/T 11364 的规定编制
This table is prepared in accordance with the provisions of SJ/T 11364.
O:
表示该有毒有害物质在该部件所有均质材料中的含量均在
GB/T 26572
标准规定的限量要求以下.
O: Indicates that this hazardous substance contained in all of the homogeneous materials for this part is below the limit
requirement of GB/T 26572.
X:
表示该有毒有害物质至少在该部件的某一均质材料中的含量超出
GB/T 26572
标准规定的限量要求.
X: Indicates that this hazardous substance contained in at least one of the homogeneous materials used for this part is
above the limit requirement in GB/T 26572.
在中国大陆销售的相应电子信息产品（EIP）都必须遵照中国大陆《电子电气产品有害物质限制使用标识要
求》标准贴上环保使用期限（EFUP）标签。Barco 产品所采用的 EFUP 标签（请参阅实例，徽标内部的编号
使用于指定产品）基于中国大陆的《电子信息产品环保使用期限通则》标准。
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with the “Marking for the restriction of the use of hazardous substances in electrical
and electronic product” of Chinese Mainland, marked with the Environmental Friendly Use
Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the
photo) is based on the “General guidelines of environment-friendly use period of electronic information products” of Chinese Mainland.
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
_______________________________________________________
85
Page 90
86
_____________________________________________________________
Barco - KVD5521, IVD5521, HVD5521 - R591341 - User Manual - Revision 05 - November 2016
Page 91
Loading...