Page 1
HDX series
User and Installation manual
For HDX, HDX W12, HDX W 14,HDX W1 8 and HDX W20
R5905032/17
23/01/2018
Page 2
Product revision
Software version: 1.10.
Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
Phone: +32 56.36.82.11
Fax: +32 56.36.883.86
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
Printed in Belgium
Page 3
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site w
h
ttps://www.barco.com/en/signin.
ww.barco.com or from the secured Barco web site
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
EMC statements
EN55032/CISPR32 Class A MME (MultiMedia Equipment)
Warning : This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interfer-
ence.
Class A ITE (Information Technology Equipment)
Warning : This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may
cause harmful interference, in which case the user will be responsible for correcting any interference at his own expense
Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment
GNU-GPL code
If you would like a copy of the GPL source code contained in this product shipped to you on CD, please contact Barco. The cost of preparing
and mailing a CD will be charged.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,
in particular if the systems are operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in
the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures
which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal
maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the
customer.
Page 4
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufacturers.
Page 5
Table of contents
TABLE OF CONTENTS
1. Safety................................................................................................................. 7
1.1 General considerations............................................................................................................... 7
1.2 Important safety instructions ......................................................................................................... 8
1.3 Light beam Hazard Distance (HD) ..................................................................................................10
1.4 HD infunction of the lensThrow Ratio(TR)........................................................................................12
1.5 Important warnings concerning HDX flight cases ..................................................................................12
2. General..............................................................................................................13
2.1 Installation requirements .. . .........................................................................................................13
2.2 Unpacking the projector .............................................................................................................14
2.3 Initial inspection......................................................................................................................15
2.4 HDX flight case......................................................................................................................16
2.5 Projector configurations .............................................................................................................16
2.6 Projector air inlets and outlets.......................................................................................................20
2.7 Free downloadof Projector Toolset.................................................................................................20
2.8 Installationprocessoverview........................................................................................................21
3. Pulse Remote Control Unit ......................................................................................23
3.1 Remote control, Battery installation.................................................................................................23
3.2 Remote control, protocolsetup .....................................................................................................24
3.3 Remote control, on/off button .......................................................................................................24
3.4 Functions ofthe“buttonpressedindicator”.........................................................................................25
3.5 Displaying and Programming addressesinto the RCU ............................................................................25
3.6 Using the XLR connector of the RCU...............................................................................................25
3.7 Using the mini-jack connector of the RCU. . ........................................................................................26
3.8 Silicone protection sleeve for the RCU (optional) ..................................................................................26
4. Physical installation ..............................................................................................29
4.1 Lenses ...............................................................................................................................29
4.1.1 Available lenses...............................................................................................................29
4.1.2 Lens selection .................................................................................................................30
4.1.3 Lens installation ...............................................................................................................31
4.1.4 Lens removal . .................................................................................................................32
4.1.5 Lens safety cable .............................................................................................................33
4.1.6 Lens shift, zoom & focus......................................................................................................35
4.1.7 Scheimpflugadjustment ......................................................................................................36
4.2 Connecting the projector with the power net .......................................................................................40
4.3 Alignment of a table mounted projector. . . . . ........................................................................................41
4.4 Mounting the bottom carry handler .................................................................................................41
4.5 Mounting the top carry handler......................................................................................................43
4.6 Suspension of the projector with rigging clamps ...................................................................................44
4.7 Alignment of a ceiling mounted projector . . . ........................................................................................46
5. Input & Communication..........................................................................................49
5.1 Introduction ..........................................................................................................................49
5.2 Input source connections. . . .........................................................................................................50
5.3 Communication connections ........................................................................................................52
5.4 Utility-Accessory Outlet..............................................................................................................55
6. Getting started .....................................................................................................57
6.1 RCU & Local keypad................................................................................................................57
6.2 Terminology overview ...............................................................................................................57
6.3 Poweron projector ..................................................................................................................59
6.4 Switching to standby ................................................................................................................62
6.5 Poweroff projector ..................................................................................................................62
6.6 Status LEDs .........................................................................................................................63
6.7 Using the RCU.......................................................................................................................63
6.8 Projector Address....................................................................................................................65
6.8.1 Displaying and Programming addresses into the RCU . . ....................................................................65
6.8.2 Controlling the projector ......................................................................................................65
6.9 Source selection.....................................................................................................................65
7. Quick set up adjustment.........................................................................................67
7.1 Textboxes ONor OFF ..............................................................................................................67
7.2 Quick Lens Adjustment via LENS key ..............................................................................................67
7.3 Direct Lens Adjustment (RCU)......................................................................................................69
7.4 Quickpicture inpicture..............................................................................................................69
7.5 Quick language selection ...........................................................................................................70
8. Start up of the adjustment mode ...............................................................................73
8.1 About the adjustment mode .........................................................................................................73
8.2 Aboutthe use ofthe remotecontrolandthelocal keypad.........................................................................73
8.3 Start up the adjustment mode.......................................................................................................73
R5905032 HDX SERIES 23/01/2018
1
Page 6
Table of contents
8.4 Navigation and adjustments.........................................................................................................74
8.5 Menu memory .......................................................................................................................75
8.6 Shortcut keys to the menus .........................................................................................................75
8.7 Test patterns in adjustment mode. ..................................................................................................76
8.8 Help informationin adjustment mode...............................................................................................76
9. Input .................................................................................................................77
9.1 Input menu overview ................................................................................................................77
9.2 Input Selection.......................................................................................................................78
9.3 Advanced Settings...................................................................................................................79
9.3.1 About Input Setup .............................................................................................................79
9.3.2 Input configuration ............................................................................................................79
9.3.3 DVI - RGB input...............................................................................................................80
9.3.4 SDI input ......................................................................................................................80
9.3.5 5 cable input. . .................................................................................................................82
9.3.6 HDMI - DisplayPort input (3D input module) .................................................................................82
9.4 Input locking . ........................................................................................................................82
9.5 Minimum delay.......................................................................................................................84
9.6 Native resolution.....................................................................................................................85
9.7 No Signal ............................................................................................................................86
9.7.1 Backgroundcolor .............................................................................................................86
9.7.2 Background Logo .............................................................................................................87
9.7.3 Shutdown settings ............................................................................................................87
9.7.4 Shutdown retarding time......................................................................................................88
9.7.5 Auto Dimming.................................................................................................................89
9.8 EDID .................................................................................................................................90
9.8.1 Configure an input .. . .........................................................................................................90
9.8.2 Create custom EDID file......................................................................................................91
9.8.3 Delete a custom EDID file ....................................................................................................93
9.8.4 Delete all custom EDID file...................................................................................................94
9.9 3D input ..............................................................................................................................94
9.9.1 About 3D modes ..............................................................................................................94
9.9.2 Activate 3D....................................................................................................................97
9.9.3 Auto detection.................................................................................................................98
9.9.4 Input type selection ...........................................................................................................99
9.9.5 3D second input..............................................................................................................100
9.9.6 L-R Synchronisation, field dominance.......................................................................................101
9.9.7 L-R Synchronisation,Invert 3D sync out....................................................................................102
10. Image .............................................................................................................. 105
10.1 Image menu overview ..............................................................................................................105
10.2 Start up the Image adjustments . . . .................................................................................................106
10.3 Image settings ......................................................................................................................106
10.3.1 Contrast ......................................................................................................................106
10.3.2 Brightness....................................................................................................................107
10.3.3 Saturation ....................................................................................................................108
10.3.4 Phase.........................................................................................................................109
10.3.5 Color temperature (fixedvalues)............................................................................................111
10.3.6 Color temperature (custom values) .........................................................................................112
10.3.7 Input Balance ................................................................................................................113
10.3.7.1 Introduction to Input Balance . . .......................................................................................113
10.3.7.2 Adjusting the inputbalance ...........................................................................................114
10.3.8 Image settings, defaults .....................................................................................................117
10.4 Aspect Ratio ........................................................................................................................118
10.5 Timings..............................................................................................................................120
10.5.1 Source timings...............................................................................................................120
10.5.2 Advanced timings, clamp delay - clamp width ..............................................................................121
10.6 Image File Services ................................................................................................................123
10.6.1 Files and file manipulations. .................................................................................................123
10.6.2 Manual Load file .............................................................................................................123
10.6.3 File Load Filter ...............................................................................................................124
10.6.4 Delete a file ..................................................................................................................124
10.6.5 Delete all custom files .......................................................................................................126
10.6.6 Rename custom files ........................................................................................................127
10.6.7 Copy custom file .............................................................................................................128
10.6.8 Image file service options, Load file.........................................................................................129
10.6.9 Image file service options, Auto Picture Alignment .........................................................................130
10.7 Savecustom settings...............................................................................................................131
10.8 Splashimage.......................................................................................................................131
11. Layout ............................................................................................................. 135
11.1 Layout menu overview .............................................................................................................135
11.2 Introduction .........................................................................................................................135
11.3 Main window . .......................................................................................................................136
11.3.1 Main window source selection...............................................................................................136
11.3.2 Main window size ............................................................................................................137
2
R5905032 HDX SERIES 23/01/2018
Page 7
Table of contents
11.3.3 Main window position ........................................................................................................138
11.4 PiP window . . .......................................................................................................................139
11.4.1 Introduction to PIP .. . ........................................................................................................140
11.4.2 Picture inPicture activation..................................................................................................140
11.4.3 PiP window, source selection................................................................................................141
11.4.4 PiP window, Size ............................................................................................................142
11.4.5 PiP window, position . ........................................................................................................143
11.5 LayoutFile Services................................................................................................................145
11.5.1 Load layout file...............................................................................................................145
11.5.2 Rename layout file ...........................................................................................................146
11.5.3 Delete layout file .............................................................................................................146
11.5.4 Delete all layout files.........................................................................................................147
11.5.5 Copy or Save as layout file ..................................................................................................148
11.6 Lens behavior.......................................................................................................................149
12. Lamp............................................................................................................... 151
12.1 Lampmenuoverview...............................................................................................................151
12.2 Lamppower mode..................................................................................................................151
12.3 Lamppower.........................................................................................................................152
12.4 Auto dimming when on Pause .....................................................................................................152
12.5 Auto dimming when No Signal .....................................................................................................152
12.6 Auto dimming when Over-temperature............................................................................................153
12.7 CLO mode (Constant light output mode) . . . .......................................................................................153
12.8 CLO targets.........................................................................................................................155
12.9 LPS power ..........................................................................................................................155
12.10 Lamp identification..................................................................................................................155
12.11 Z-axisadjustment...................................................................................................................156
13. Alignment......................................................................................................... 157
13.1 Alignment menu overview..........................................................................................................157
13.2 Orientation ..........................................................................................................................158
13.3 Lens adjustment, zoom - focus ....................................................................................................159
13.4 Lens adjustment, shift ..............................................................................................................160
13.5 Lens adjustment, mid position .....................................................................................................161
13.6 Calbrate lensat startup.............................................................................................................161
13.7 Calibrate lens.......................................................................................................................162
13.8 Warping.............................................................................................................................163
13.8.1 About warping................................................................................................................164
13.8.2 Warp activation - deactivation ...............................................................................................164
13.8.3 Start up manualadjustment .................................................................................................165
13.8.4 Warp adjustment principle...................................................................................................166
13.8.5 Setting the warping level..................................................................................................... 169
13.8.6 Warp adaptation steps.......................................................................................................169
13.8.7 Making selections and adjustments . . .......................................................................................170
13.8.8 Keystone correction workflow ...............................................................................................171
13.8.9 Linearity adjustment, workflow ..............................................................................................172
13.8.10 Selecting and changing the position of a specific point.....................................................................173
13.8.11 Scaling the image............................................................................................................173
13.8.12 Shifting the image............................................................................................................174
13.8.13 Rotating the image. . . ........................................................................................................174
13.8.14 Hardware Reset..............................................................................................................176
13.8.15 OSD opacity..................................................................................................................176
13.8.16 Warp file service, load file ...................................................................................................177
13.8.17 Warp file service, save to file................................................................................................178
13.8.18 Warp file service,save as ...................................................................................................179
13.8.19 Warp file service, rename file................................................................................................180
13.8.20 Warp file service, delete file .................................................................................................181
13.8.21 Warp file service, delete all files.............................................................................................182
13.8.22 Warp board reset.............................................................................................................183
13.8.23 Warp board and values reset................................................................................................184
13.8.24 Alternative SideKeystone ................................................................................................... 185
13.9 Blanking adjustment................................................................................................................186
13.10 Contrast-Intensity...................................................................................................................188
13.11 Gamma .............................................................................................................................189
13.12 Internal patterns ....................................................................................................................189
13.13 Color space.........................................................................................................................190
13.14 Scenergix ...........................................................................................................................192
13.14.1 Introduction. . . ................................................................................................................192
13.14.2 Preparations. . ................................................................................................................193
13.14.3 Scenergix activation .........................................................................................................193
13.14.4 Scenergix pattern ............................................................................................................194
13.14.5 Scenergix adjustment lines ..................................................................................................195
13.14.6 Data doubling ................................................................................................................196
13.14.7 White level adjustment (blending area) . . . ..................................................................................197
13.14.8 Black level adjustment.......................................................................................................200
13.14.9 Scenergix Reset .............................................................................................................203
R5905032 HDX SERIES 23/01/2018
3
Page 8
Table of contents
13.15 3DGlasses .........................................................................................................................204
13.15.1 Dark timeadjustment ........................................................................................................204
13.15.2 Left-right output reference delay ............................................................................................ 207
13.15.3 3D Sync Loop Through ......................................................................................................208
13.15.4 Upper limit for triple or double flash.........................................................................................209
13.16 High End Systems Mirror...........................................................................................................210
14. Projector Control................................................................................................ 213
14.1 Projector Control menu overview . .................................................................................................213
14.2 Individual Projector Address .......................................................................................................214
14.3 Projector CommonAddress........................................................................................................215
14.4 Serial Communication ..............................................................................................................216
14.4.1 Baud ratesetup .............................................................................................................. 216
14.4.2 Interface Standard ...........................................................................................................216
14.5 Network.............................................................................................................................217
14.5.1 Introduction to a Network connection .......................................................................................217
14.5.2 Wired DHCP set up..........................................................................................................218
14.5.3 Wired IP address set up .....................................................................................................219
14.5.4 Wired subnet mask set up . . .................................................................................................220
14.5.5 Wired default gateway set up................................................................................................222
14.5.6 Wireless network activation.................................................................................................. 223
14.5.7 Wireless access points selection and setup ................................................................................224
14.5.8 Wireless DHCP set up .......................................................................................................226
14.5.9 Wireless fixed IP address set up ............................................................................................227
14.5.10 Wireless subnet mask set up ................................................................................................228
14.5.11 Wireless default gateway set up.............................................................................................230
14.6 IRControlswitching ................................................................................................................231
14.7 DMX.................................................................................................................................232
14.7.1 DMX address. ................................................................................................................232
14.7.2 DMX universe................................................................................................................ 234
14.7.3 DMX mode . . . ................................................................................................................235
14.7.4 Art-Net DMX..................................................................................................................236
14.7.5 Front XLR output voltage control............................................................................................237
14.7.6 Monitor .......................................................................................................................239
14.7.7 DMX Shutdown ..............................................................................................................240
14.7.8 DMX Shutdownretarding time...............................................................................................240
14.8 Buttons..............................................................................................................................241
14.8.1 Standby button ...............................................................................................................241
14.8.2 Shortcut keys.................................................................................................................242
14.9 Menuposition.......................................................................................................................243
14.10 Local LCD...........................................................................................................................244
14.11 Language selection. ................................................................................................................245
14.12 Scheduler ...........................................................................................................................246
14.12.1 Add a task tothelist ......................................................................................................... 246
14.12.2 Edita task....................................................................................................................249
14.12.3 Delete task ...................................................................................................................251
14.12.4 Scheduler, on or off . . ........................................................................................................252
14.13 GSM Configuration,activation.....................................................................................................253
14.14 GSM Configuration,subscription ..................................................................................................255
14.15 FLEX, light output configuration....................................................................................................257
14.15.1 About FLEX, Lightoutput control............................................................................................257
14.15.2 Light output configuration via OSD menu . ..................................................................................258
14.15.3 Configure projector’s light output via SMS..................................................................................259
14.16 SMS services.......................................................................................................................259
14.16.1 Request for notifications .....................................................................................................259
14.16.2 Request for information ......................................................................................................260
14.16.3 Lamp ignition admission..................................................................................................... 260
15. Service ............................................................................................................ 261
15.1 Service menu overview.............................................................................................................261
15.2 Identification ........................................................................................................................262
15.3 Diagnosis ...........................................................................................................................263
15.3.1 Versions......................................................................................................................263
15.3.2 Measurements............................................................................................................... 264
15.3.3 Logging.......................................................................................................................265
15.3.4 Board Id ......................................................................................................................267
15.3.5 Notification ...................................................................................................................267
15.3.6 Tiltsensor ....................................................................................................................268
15.4 Internal Service Patterns...........................................................................................................269
15.5 Convergence .......................................................................................................................273
15.6 Factorydefaults.....................................................................................................................275
15.7 USB memory .......................................................................................................................276
15.8 Reset Formatter ....................................................................................................................277
15.9 Refill mode . . . .......................................................................................................................278
15.10 Save Custom Settings..............................................................................................................279
15.11 Special HD Camera mode . ........................................................................................................280
4
R5905032 HDX SERIES 23/01/2018
Page 9
Table of contents
15.12 Auto Dimming when over-temperature ............................................................................................281
15.13 TimeandDate......................................................................................................................281
16. Maintenance...................................................................................................... 283
16.1 Cleaning the lens . . . ................................................................................................................283
16.2 Cleaning the exterior of the projector ..............................................................................................283
17. Servicing.......................................................................................................... 285
17.1 Inserting an input module .. ........................................................................................................285
17.2 Removal of the lamp house ........................................................................................................286
17.3 Installation of the lamp house ......................................................................................................287
17.4 Removal of thefront cover .........................................................................................................288
17.5 Mounting the front cover . . . ........................................................................................................290
17.6 Removal of thelamp cover.........................................................................................................291
17.7 Mounting the lamp cover . . .........................................................................................................292
17.8 Replacement of the high density dust filter........................................................................................293
17.9 Remove and clear metal front filter ................................................................................................294
A. Dimensions ........................................................................................................ 297
A.1 Dimensions ofa HDX projector....................................................................................................297
B. Specifications ..................................................................................................... 299
B.1 Specifications of the HDX W12 ....................................................................................................299
B.2 Specifications of the HDX W14 ....................................................................................................300
B.3 Specifications of the HDX W18 ....................................................................................................301
B.4 Specifications of the HDX W20 FLEX .............................................................................................302
B.5 Technical Regulations ..............................................................................................................304
C. Standard source files............................................................................................ 305
C.1 Table overview......................................................................................................................305
D. DMX chart.......................................................................................................... 309
D.1 DMX chart, Basic ...................................................................................................................309
D.2 DMX chart, Full.....................................................................................................................309
D.3 DMX chart, Extended...............................................................................................................310
E. Stacking HDX projector projectors............................................................................ 313
E.1 Mount stacking points ..............................................................................................................313
E.2 Stacking HDX projectorprojectors.................................................................................................313
E.3 AligningstackedHDXprojector projectors ........................................................................................316
F. Environmental information ...................................................................................... 319
F.1 Disposalinformation................................................................................................................319
F.2 RoHS compliance ..................................................................................................................320
F.3 Production address . ................................................................................................................321
F.4 Importers contact information ......................................................................................................321
Index.................................................................................................................... 323
R5905032 HDX SERIES 23/01/2018 5
Page 10
Table of contents
6 R5905032 HDX SERIES 23/01/2018
Page 11
1. SAFETY
About this chapter
Read this chapter attentively. It contains important information to prevent personal injury while installing and using a HDX projector.
Furthermore, it includes several cautions to prevent damage to the HDX projector. Ensure that you understand and follow all safety
guidelines, safety instructions and warnings mentioned in this chapter before installing your HDX projector. After this chapter, additional “warnings” and “cautions” are given depending on the installation procedure. Read and follow these “warnings” and “cautions”
as well.
1.1 General considerations
WARNING: Ensure you understand and follow all the safety guidelines, safety instructions, warnings and
cautions mentioned in this manual.
WARNING: Be aware of suspended loads.
1. Safety
WARNING: Wear a hard hat to reduce the risk of personal injury.
WARNING: Be careful while working with heavy loads.
WARNING: Mind your fingers while working with heavy loads.
CAUTION: High pressure lamp may explode if improperly handled.
General safety instructions
• Before operating this equipment please read this manual thoroughly and retain it for future reference.
• Installation and preliminary adjustments should be performed by qualified Barco personnel or by authorized Barco service deal-
ers.
• All warnings on the projector and in the documen
• All instructions for operating and use of this equipment must be followed precisely.
• All local installation codes should be adhered to.
tation manuals should be adhered to.
Notice on safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, EN60950-1,
UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology equipment including
electrical business equipment. These safety standards impose important requirements on the use of safety critical components,
materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having access
to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability
and strength, enclosure construction and protection against the risk of fi re. Simulated single fault condition testing ensures the
safety of the equipment to the user even when the equipment’s normal operation fails.
Users definition
Throughout this manual, the term S
necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize
R5905032 HDX SERIES 23/01/2018 7
ERVICE PERSONNEL refers to persons having appropriate technical training and experience
Page 12
1. Safety
the potential risk to themselves or other persons. The term USER and OPERATOR refers to any person other than SERVICE PERSONNEL, AUTHORIZED to operate professional projection systems.
A HDX projector is intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with potential hazards
associated with high voltage, high intensity light beams, ultraviolet exposure and high temperatures generated by the lamp and
associated circuits. Only qualified SERVICE PERSONNEL, knowledgeable of such risks, are allowed to perform service functions
inside the product enclosure.
1.2 Important safety instructions
To prevent the risk of electrical shock
• This product should be operated from a mono phase AC power source.
• This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power cables
are the correct one, consult your dealer.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the
purpose of the grounding-type plug.
• Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect
the cord, pull it out by the plug. Never pull the cord itself.
• Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety
tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer.
• Do not operate the projector with a damaged cord. Replace the cord.
Do not operate the projector if the projector has been dropped or damaged - until it has been examined and approved for
operation by a qualified service technician.
• Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
• If an extension cord is necessary, a cord with a current rating at least equ
for less amperage than the projector may overheat.
• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out
parts that could result in a risk of fi re or electrical shock.
• Do not expose this projector to rain or moisture.
• Do not immerse or expose this projector in water or other liquids.
• Do not spill liquid of any kind on this projector.
• Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before
resuming operations.
• Do not disassemble this projector, always take it to an authorized trained service person when service or repair work is required.
• Do not use an accessory attachment which is not recommended by the manufacturer.
• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will preven
t damage to the device due to lightning and AC power-line surges.
al to that of the projector should be used. A cord rated
To prevent personal injury
• Isolate electrically before replacing the lamp or lamp house. Caution: Hot lamp (house).
• Caution: High pressure lamp may explode if improperly handled. Refer servicing to qualified service personnel.
• To prevent injury and physical damage, always read this manual and all labels on the system before inserting the lamp casing,
connecting to the wall outlet or adjusting the projector.
• To prevent injury, take note of the weight of the projector. Minimum 4 persons are needed to carry the projector.
• To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
• Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.
• Warning: extremely high brightness lamps: This projector uses extr
directly into the lens or at the lamp. If the projection distance is less than 6 meter, any person needs to be at least 4 meters
away from the projected image. Avoid close range reflection of the projected image on any reflecting surface (such as glass,
metal, …) . When operating the projector, we strongly
• Before attempting to remove any of the projector’s covers, you must turn off the projector and disconnect from the wall outlet.
• When required to switch off the projector, to access parts inside, always disconnect the power cord from the power net.
• The power input at the projector side is considered as the disconnect device. When required to switch off the projector, to
access parts inside, always disconnect the power cord at the projector side. In case the power input at the projector side is not
accessible (e.g. ceiling mount), the socket outlet supplying the projector shall be installed nearby the projector and be easily
accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring.
• Never stack more than two (2) HDX projectors in a hanging configuration (truss) and never stack more than three (3) HDX
projectors in a base stand configuration (table mount).
• When using the projector in a hanging configuration, always mount 2 safety cables. See installation manual for the correct use
of these cables.
• Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and
possible injury to the user.
8
recommend wearing suitable safety glasses.
emely high brightness lamps. Never attempt to look
R5905032 HDX SERIES 23/01/2018
Page 13
1. Safety
• It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if they have become
visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches.
• Warning: Protection from ultraviolet radiation: Do not look directly in the light beam. The lamp contained in this product is
an intense source of light and heat. One component of the light emitted from this lamp is ultraviolet light. Potential eye and skin
hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unnecessary exposure. Protect yourself and
your employees by making them aware of the hazards and how to protect themselves. Protecting the skin can be accomplished
by wearing tightly woven garments and gloves. Protecting the eyes from UV can be accomplished by wearing safety glasses
that are designed to provide UV protection. In addition to the UV, the visible light from the lamp is intense and should also be
considered when choosing protective eye wear.
• Exposure to UV radiation: Some medications are known to make individuals extra sensitive to UV radiation. The American
Conference of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure for an-8 hour day to be
less than 0,1 micro-watts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to assure
employees are not exposed to cumulative radiation levels exceeding these government guidelines. The exposer of this UV
radiation is allowed for only 1 hour per day for maintenance and service persons.
• Cooling liquid circuit. The projector contains a cooling circuit fi lled with Blue antifre
eze diluted (1/3 ethanediol – 2/3 Demi
water).
When the cooling circuit leaks, switch off the device and contact a service technician.
The liquid is not for household use. Keep out of reach of children. Harmful by oral intake. A
void exposure to pregnant women.
Avoid contact with eyes, skin and clothing. Avoid inhale of the noxious fumes.
• When the projector is mounted above persons, mount always a lens safety cable.
To prevent fire hazard
• Do not place flammable or combustible materials near the projector!
• Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This
projector radiates heat on its external surfaces and from ventila
safe. Exposing flammable or combustible materials into close proximity of this projector could result in the spontaneous ignition
of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external
surfaces of the projector whereby no flammable or combustibl
40 cm (16”) for all DLP projectors. The exclusion zone on the lens side must be at least 5 m. Do not cover the projector or the
lens with any material while the projector is in operation. Keep flammable and combustible materials away from the projector at
all times. Mount the projector in a well ventilated area
away from sources of ignition and out of direct sun light. Never expose
the projector to rain or moisture. In the event of fire, use sand, CO
electrical fi re. Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine
Barco replacement parts. Never use non-Barco repl
acement parts as they may degrade the safety of this projector.
• Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect
it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the
projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat
register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
• Projection rooms must be well ventilated or cooled in order to avoid build up of heat.
• Let the projector cool down completely before storing. Remove cord from the projector when storing.
• Heat sensitive materials should not be placed in the path of the exhausted air or on the lamp house.
tion ducts during normal operation, which is both normal and
e materials are present. The exclusion zone must be not less than
or dry powder fire extinguishers. Never use water on an
2
To prevent projector damage
• This projector has been designed for use with a specific lamp (house) type. See installation instructions for its correct type.
• The air fi lters of the projector must be cleaned or replaced on regular base (a "clean" booth would be monthly-minimum).
Neglecting this could result in disrupting the air flow inside the projector, causing overheating. Overheating may lead to the
projector shutting down during operation.
• The projector must always be installed in a manner which ensures free flow of air into its air inlets and unimpeded evacuation
of the hot air from its cooling system.
• In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic Compatibility (EMC)
requirements, it should always be operated with all of it’s covers in place.
• Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product
on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The
device should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
• Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the mains
supply immediately. Do not operate the projector again until it has been checked by qualified service personnel.
• Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects may not be
nearer to the projector than 1
• Do not use this equipment near water.
• Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as high power
laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices
which case there is a loss of warranty.
• Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror Devices
case there is a loss of warranty.
• Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For
maximum protection, repack your set as it was originally packed at the factory.
0 cm (4") on any side.
TM
in which
TM
in
R5905032 HDX SERIES 23/01/2018
9
Page 14
1. Safety
• Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet.
Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution.
• To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective
coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent
solution, or thinner.
• Rated maximum ambient temperature, t
• The lamp house shall be replaced if it has become damaged or thermally deformed.
= 40 °C (104 °F).
a
On servicing
• Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials
and risk of electric shock.
• Refer all servicing to qualified service personnel.
• Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can
lead to permanent damage to the projector and cancellation of the warranty.
• Unplug this product from the wall outlet and refer servicing to qualified service technicians under the following conditions:
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.
• Replacement parts: When replacement parts are required, be sure the service technici
parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may
void warranty.
• Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks
to determine that the product is in proper operating condition.
• Possible explosion hazard: Always keep in mind the caution below:
an has used original Barco replacement
CAUTION: Xenon compact arc lamps are highly pressurized. When ignited, the normal
of the bulb increases the pressure to a level at which the bulb may explode if not handled in strict accordance
to the manufacturer’s instructions. The bulb is stable at room temperature, but may still explode if dropped or
otherwise mishandled. Whenever the lamp house, containing a xenon lamp, has t
the protective container or cloth has to be removed from the xenon lamp, authorized protective clothing MUST
be worn!
operating temperature
o be dismantled or whenever
To prevent battery explosion
• Danger of explosion if battery is incorrectly installed.
• Replace only with the same or equivalent type recommended by the manufacturer.
• For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and regulations
to ensure proper disposal.
Safety Data Sheets for Hazardous Chemicals
For safe handling information on chemical products, consult the Safety Data Sheet (SDS). SDSs are available upon request via
safetydatasheets@barco.com.
1.3 Light beam Hazard Distance (HD)
HD
Light beam Hazard Distance (HD) is the distance from the source at which the intensity or the energy per surface unit
becomes lower than the applicable safety limit. The light beam can thus be considered as dangerous if the operator
is closer from the source than the HD.
Restriction Zone (RZ) based on the HD
The HD is defined from the projection lens surface towards the position of the lowest projected beam where the irradiance equals
the applicable safety limit. The HD depends on the amount of lumens produced by the projector and the type of lens installed. See
next chapter HD in function of the lens Throw Ra tio (TR).
10
R5905032 HDX SERIES 23/01/2018
Page 15
1. Safety
To protect untrained users the installation shall comply with the following installation requirements: light output levels in excess of the
limits shall not be permitted at any point less than 2.0 meters (SH image 1-1) above any surface upon which persons are assumed
to stand or 1 meter (SW image 1-1) below or in lateral separation from any place where such persons are assumed to be. See
image 1-1.
RA TH
HD
RA
SH
RZ
SH
Image 1-1
ASideview.
B Top view.
RA Restricted Access location (booth area of projector).
PR Projector.
TH Theater.
RZ Restriction Zone in the theater.
SH Separation Height. Must be minimum 2 meter.
SW Separation Width. Must be minimum 1 meter.
Based on national requirements, no person is allowed to enter the projected beam within the zone between the projection lens and
the related hazard distance (HD). This shall be physically impossible by creating sufficient separation height or by placing barriers.
The minimum separation height takes into account the surface upon which persons are assumed to stand.
On image 1-1 a typical setup is displayed. It must be verified by the installer if these minimum requirements are met. If required a
restricted zone (RZ) in the theater must be established. This can be done by using physical barrier, like a red rope as illustrated in
image 1-2.
PR
(B) TOP VIEW(A) SIDE VIEW
TH
HD
SW
SW
SW
RZ
1m
SW
Image 1-2
PR
R5905032 HDX SERIES 23/01/2018 11
Page 16
1. Safety
1.4 HD in function of the lens Throw Ratio (TR)
TR (Throw Ratio)
The ratio of the distance to the screen (throw) to the screen width.
HDX projector Hazard Distance
8
7
6
5
4
HD [m]
3
2
1
0
0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0 7,5 8,0 8,5 9,0 10,0
Image 1-3
HD (in meter) in function of the Throw Ratio (TR)
TR
1.5 Important warnings concerning HDX flight cases
Important warnings concerning stacking/transporting HDX rental flight cases
• Stack maximum two (2) HDX rental flight cases high. Never higher.
• Surface on which flight case is standing m
The surface must also be able to support the load safely.
• Before stacking or transporting flight cases, check the wheels and their fixation screws for wear or defects.
• Before stacking or transporting flight cases, check that the four lock handles on each fl ight case are in good working order and
locked securely.
• When stacked, make sure the wheels of the upper fl ight case are precisely positioned in the stacking dishes of the flight case
below.
•Stackedflight cases may not be moved. Before stacking, the lower flight case must already be in its final resting position before
placing the second upon it.
• Never stack loaded flight cases in a truck or other transport medium, unless each flight case is rigidly strapped tight.
• In the event of a wheel breaking, flight cases must be rigidly strapped tight to prevent a stack collapsing.
• Use an appropriate forklift to raise flight cases and take the necessary precautions to avoid personnel injury.
ust be level to ensure that the total load is evenly spread out among the four wheels.
12
R5905032 HDX SERIES 23/01/2018
Page 17
2. GENERAL
About this chapter
Read this chapter before installing your HDX projector. It contains important information concerning installation requirements for the
HDX projector, such as minimum and maximum allowed ambient temperature, humidity conditions, required safety area around the
installed projector, required power net, etc.
Furthermore, careful consideration of things such as image size, ambient light level, projector placement and type of screen to use
are critical to the optimum use of the projection system.
Overview
• Installation requirements
• Unpacking the projector
• Initial inspection
• HDX fl ight case
• Projector configurations
• Projector air inlets and outlets
• Free download of Projector Toolset
• Installation process overview
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. Observing the specification mentioned in this chapter is critical for projector performance. Neglecting
this can result in loss of warranty.
2. General
2.1 Installation requirements
Environment conditions
Table below summarizes the physical environment in which the HDX projector m
Environment
Ambient Temperature
Humidity
Altitude
Let the projector acclimatize after unpacking. Neglecting this may result in a startup failure of the Light Processor Unit.
Operating Non-Operating
10 °C (50 °F) to 40 °C (104 °F) -15°C (5°F) to 60°C (140°F)
0% RH to 80% RH Non-condensed 0% RH to 90% RH Non-Condensed
-60 m (-197 Ft) to 3000 m (9843Ft) -60 m (-197 Ft) to 10000 m (32810 Ft)
Cooling requirements
The projector is fan cooled and must be installed with sufficient space around the projector head, minimum 10 cm (4 inch) to ensure
sufficient air flow. It should be used in an area where the ambient temperature, as measured at the projector air inlet , does not
exceed +40°C (+104°F).
Clean air environment
A projector must always be mounted in a manner which ensures the free fl ow of clean air into the projectors ventilation inlets. For
installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines or
similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading
performance), then it is highly advisable and desirable to have this contamination removed prior to it reaching the projectors clean
air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not a
feasible solution then measures to relocate the projector to a clean air environment should be considered.
Only ever use the manufacturer’s recomme
use industrial strength cleaners on the projector’s optics as these will degrade optical coatings and damage sensitive optoelectronics
components. Failure to take suitable precautions to protect the projector from the effects of persistent and prolonged air contaminants will culminate in extensive an
be noneffective and impracticable. Damage of this nature is under no circumstances covered under the manufacturer’s warranty
and may deem the warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any
repair. It is the clients responsi
bility to ensure at all times that the projector is protected from the harmful effects of hostile airborne
nded cleaning kit which has been specifically designed for cleaning optical parts, never
d irreversible ingrained optical damage. At this stage cleaning of the internal optical units will
ay be safely operated or stored.
R5905032 HDX SERIES 23/01/2018
13
Page 18
2. General
particles in the environment of the projector. The manufacturer reserves the right to refuse repair if a projector has been subject to
knowingly neglect, abandon or improper use.
Main Power requirements
The HDX projector operates from a nominal mono phase power net with a separate earth ground PE.
Power requirements : 110-130V/200-240 V, 15A, 50-60Hz
The power cord required to connect the projector with the power net is delivered with the projector.
Projector weight
Do not underestimate the weight of the HDX projector. The projector weights about ±50 kg (±111 lb.) without lens. Be sure that the
pedestal on which the projector has to be installed is capable of handling five (5) times the complete load of the system.
2.2 Unpacking the projector
What has to be done ?
Upon delivery, the projector is packed in a carton box upon a wooden pallet and secured with banding and
thermore, to provide protection during transportation, the projector is surrounded with foam. Once the projector has arrived at the
installation site, it needs to be removed from the carton box and wooden pallet in a safe manner without damaging the projector.
After unpacking let the projector acclimatize to a room temperature higher then 10°C (50°F) and lower then
40°C (104°F). Neglecting this may result in a start up failure of the Light Processor Unit.
fastening clips. Fur-
Necessary tools
cutter knife
How to unpack
1. Remove the banding around the carton box, by releasing the fastening clips as illustrated, and open the box.
Image 2-1
Opening box
2. Remove the small box on top of the projector. This box contains the accessories such as manuals, remote control, etc.
14
R5905032 HDX SERIES 23/01/2018
Page 19
Image 2-2
Remove carton and foam rubber
3. Take out the foam rubber.
4. Take out the projector.
2. General
Save the original shipping cardboard box and packing material. They will be necessary if you ever have to
ship your projector. For maximum protection, repack your projector as it was originally packed at the factory.
A rubber foam inside a plastic bag is placed into the lens opening of the projector. It’s recommended to reuse
this foam and plastic back each time you transport the projector. This to prevent intrusion of dust and foreign
particles.
The lens is delivered in a separate box.
2.3 Initial inspection
General
Before shipment, the projector was inspected and found to be free of mechanical and electrical defects. As soon as the projector is
unpacked, inspect for any damage that may have occurred in transit. Save all packing material until the inspection is completed. If
damage is found, file claim with carrier immediately. The Barco Sales and Service office should be notified as soon as possible.
The packaging of the HDX projector is provided with a shock-watch label. If this shock-watch label was triggered (red colored at arrival) during transport, that indicates that the package was possibly roughly handled
by the transport company. In this case, the instructions mentioned on the label, should be followed, which
are: adding a note on the “bill of lading” and informing the transport company and the Barco sales and service
office as soon as possible.
Box content
After unpacking the projector it is recommended to check if all following items where included:
• Three power cords of 2.5 meter, one CEE (7), one NEMA L6-20P and one CH2–16P
• This manual (installation manual).
• One Safety manual
• One remote control unit (RCU)
• Two AA size batteries for the RCU.
R5905032 HDX SERIES 23/01/2018
15
Page 20
2. General
One xenon lamp is mounted inside the lamp house at delivery. The projector lenses are not included in the
package of the projector.
Mechanical check
This check should confirm that there are no broken knobs or connectors, that the cabinet and panel surfaces are free of dents and
scratches, and that the operating panel is not scratched or cracked. The Barco Sales and Service office should be notified as soon
as possible if this is not the case.
2.4 HDX flight case
Introduction of the HDX flight case
The HDX flight case is designed to transport the HDX projector in a safe and secure manner. The four caster wheels, provided with
breaks, and the four handles make the HDX flight case easy to handle. The floor of the flight case wagon is equipped with two small
covered compartments to store the remote control and the rigging clamps.
Image 2-3
HDX Flight case
Order number flight case: R9864090
The dimensions of the flight case are optimal for maximum utilization of the floor area of a truck. The cover of the HDX fl ight case
has 4 stacking dishes, which allows to stack the flight cases.
WARNING: Maximum stack two (2) HDX flight cases high. Never higher.
2.5 Projector configurations
The different configurations
Depending on the installation the projector can be mounted in different ways, the different configurations are:
1. Front / Table (F/T)
2. Front / Ceiling (F/C) (upside down)
3. Front / Ceiling (F/C) (table positio
4. Rear / Table (R/T)
5. Rear / Ceiling (R/C) (upside down)
6. Rear / Ceiling (R/C) (table position)
Front projection
The projector is installed, either in a table mount or ceiling mount configuration, at the same side of the screen as the audience.
n)
16
R5905032 HDX SERIES 23/01/2018
Page 21
F/C
2. General
AUDIENCE
F/T
Image 2-4
Front projection
AUDIENCE
F/C
Image 2-5
Front proje ction, Ceiling mounted, in table position
SCREEN
FLOOR
SCREEN
FLOOR
Rear projection
The projector is installed, either in a table mount or ceiling mount configuration, at the other side of the screen opposite the audience.
AUDIENCE BACKSTAGE
R/C
R/T
Image 2-6
Rear projection
SCREEN
FLOOR
R5905032 HDX SERIES 23/01/2018 17
Page 22
2. General
Image 2-7
Rear projection, ceiling mounted in table position
Positioning the projector
AUDIENCE BACKSTAGE
R/C
SCREEN
FLOOR
SW
PD
SCREENSCREEN
SHB
SHB
ACD
SCREEN
CD
FLOOR
SW
Image 2-8
Positioning proj ector
The projector should be installed at right angles (horizontally and vertically) to the screen at a distance PD. Note the distance (A)
between lens centre and table surface is slightly variable. This distance (A) is nominal 35 cm in case all feet are turned in completely
and the vertical lens shift is set to zero (0).
On axis / off axis projection
The position of the projector with reference to the screen may also be different depending on the installation. Basically the projector
can be positioned in On-Axis or Off-Axis configuration. On-Axis configuration means that the projector is positioned so as to have
the centre of the lens coinciding with the centre of the screen. Off-Axis projection is obtained by shifting the lens up, down, left or
right. Several parameters can be calculated determining the position in any installation.
Formula to calculate the distance CD for On-Axis projection: CD=SH/2+B-A
18
R5905032 HDX SERIES 23/01/2018
Page 23
2. General
Shift range
The lens can be shifted with respect to the DMD (P) which result in a shifted image on the screen (Off-Axis). A 100% shift means that
the centre point of the projected image is shifted by half the screen size. In other words, the centre point of the projected image falls
together with the outline of the image in an On-Axis projection. Due to mechanical and optical limitations it’s recommended to keep
the shift values within the field of view (F) as illustrated below. Within these shift ranges the projector and lens perform excellently.
Configuring the projector outside these shift ranges will result in a slight decline of image quality.
U
-50% +50%
L R
D
Image 2-9
Vertical and horizontal shift range
PDMD.
F Field of view.
It is mechanical possible to shift outside the recommended field of view, but it will result in a decline of image
quality depending on the used lens and the zoom position of the used lens. Furthermore, shifting too much
in both directions will result in a blurred image corner.
Best image quality is projected in the On-Axis configuration.
+120%
-20%
F
P
F
P
P
F
U
D
L
R
SIDE VIEW
TOP VIEW
+120%
-20%
-50%
+50%
Horizontal and vertical projector tilt ranges
The projector can be rotated and mounted at any vertical angle. In other words, you can tilt the lens side of the projector as much
as desired for your application.
Side to side tilt, however, must not exceed ±15°. This limit ensures that the lamp in the projector operates properly and safely. More
tilting within area C is allowed but lamp flicker can happen.
B
MAX
15°
15°
A
A
15°
15°
MAX
360°
C
Image 2-10
A Tilting allowed without problems
B No tilting allowed in this area
R5905032 HDX SERIES 23/01/2018 19
Page 24
2. General
C Tilting allowed but lamp flicker possible
Projector lamp will not start up when out of tilt range due to build-in tilt sensor.
2.6 Projector air inlets and outlets
Air inlets and outlets
Image 2-11
The HDX projector has 3 air inlet channels and 3 air outlets. The air outlets are located at the rear of the projector. The air inlets
are located at the front of the projector.
2.7 Free download of Projector Toolset
About Projector Toolset
Projector Toolset is a software tool to set up, confi gure, manage and control Barco projectors.
The concept of this Projector Toolset software is modular. The basic package can be extended with several optional device plug-in
modules, now and in the future available.
The Projector Toolset software works wi
taken. A snapshot represents a current state of a configuration and can be reloaded to return to this typical state. These terms will
be used through the complete software.
Projector Toolset is a stand-alone application that runs on a Java Virtual Machine and that does not require extra services to run.
Several configurations can be controlled simultaneously. Even when the configurations are connected via different ways.
Projector Toolset is only availa
Where to find the download file(s)
The program and all necessary plug-ins, as well as the Reference manual can be downloaded for free from my.barco.com. Registration is necessary.
th configurations that can be loaded. Within a configuration, different snapshots can be
ble in a download version, no CD can be ordered.
20
R5905032 HDX SERIES 23/01/2018
Page 25
1. Go to the Barco website www.barco.com.
2. On the home page, click on myBarco log in.
3. On the Sign In page, enter your Email address and your password to login.
If you are not yet registered click on New to myBarco? and follow the instructions. With the created login and password, it is
possible to enter the Partnerzone of Barco.
When your login is correct, the Partnerzone is free accessible.
4. In the search fi eld, enter Projector Toolset and click on the search icon.
5. Select Technical Downloads.
6. Click on Application Software and download the Projector Toolset software package, which includes the device plug-in updates.
When downloading the complete Projector Toolset, this software contains already the latest device plug-ins. When you already have
the latest core version of Projector Toolset, it is possible to download only device plug-in updates from the same web site location.
As Projector Toolset is a stand alone application, it is not necessary to install any other software. A Java virtual machine is included
with this download.
To download the reference manual, select Reference Guide and download the latest version of the manual for your projector.
Installation
Download first the reference manual and follow the installation instructions as written in this manual.
2.8 Installation process overview
Quick setup
The following steps describe briefly how to setup your HDX projector in a table mount front projection. Note that each step refers to
a corresponding procedure, which is more detailed and illustrated.
1. Install the batteries of the remote control. See "Remote control, Battery installation", page 23
2. Place the projector on a solid table in front of the screen at the expected throw distance. Ensure that the projector is installed at
right angles (horizontally and vertically) with the screen. See "Projector configurations", page 16.
3. Select and install an appropriate lens, which covers the throw ratio ( = screen size / p
page 29.
4. Connect the projector with the local power net. See "Connecting the projector with the power net", page 40.
5. Connect your source to the appropriate input module. See "Input source connections", page 50.
6. Switch ON the projector. See "Power on projector", page 59.
7. Select the input slot to which the source is connected. Do this by press
local keypad, See "Source selection", page 65.
8. Zoom and shift the lens until the image is properly projected on the screen, Do this by using the “ZOOM” and “FOCUS” key on
the remote control unit or on the local keypad. If necessary, level the projector from side to side by turning the adjustable feet in
or out.
ing the numeric key on the remote control unit or on the
rojector screen distance). See "Lenses",
2. General
Check cooling liquid level at least every 6 months.
Every 6 months at device power up a message will be displayed on the local LCD to check the cooling liquid
level
R5905032 HDX SERIES 23/01/2018 21
Page 26
2. General
22 R5905032 HDX SERIES 23/01/2018
Page 27
3. Pulse Remote Control Unit
3. PULSE REMOTE CONTROL UNIT
3.1 Remote control, Battery installation
Where to find the batteries for the remote control ?
The batteries are not placed in the remote control unit to avoid control operation in its package, r
time. At delivery the batteries can be found in a separated bag attached to the remote control unit. Before using your remote control,
install the batteries fi rst.
How to install
1. Push the battery cover tab with the fingernail a little backwards (1) and pull, at the same time, the cover upwards (2).
esulting in a shorter battery life
1
Image 3-1
2. Insert the two AA size batteries, making sure the polarities match the + and - marks inside the battery compartment.
Tip: Use alkaline batteries for optimum range and life time.
+
-
-
+
Image 3-2
3. Insert (1) both lower tabs of the battery cover in the gaps at the bottom of the remote control, and press (2) the cover until it clicks
in place.
2
2
+
-
Image 3-3
When replacing batteries, the broadcast address of the RCU will be reset to its default value ’0’.
R5905032 HDX SERIES 23/01/2018 23
1
-
+
Page 28
3. Pulse Remote Control Unit
CAUTION: Replace with the correct battery type. Use two AA size batteries. There is a risk of explosion if the
battery is replaced with an incorrect type.
CAUTION: Replace the battery as explained above. There is a risk of explosion if the battery is incorrectly
installed.
3.2 Remote control, protocol setup
About the used protocol
The protocol is the code send out by the remote control when a button is pressed. Depending on this code, the projector can decode
the signals. The remote control can be used with two different protocols, RC5 and NEC. Depending on the projector to control the
remote control can be switched between these protocols.
Which protocol to use
•TheNEC protocol have to be used for Barco projectors based on the Pulse platform: F70, F80, F90, HDX 4K, UDX, ...
•TheRC5 protocol have to be use all other Barco projectors: HDX W, HDF W, HDQ 2K, ...
How to set
1. Remove the cover. For more info on how to remove, see "Remote control, Battery installation", page 23.
2. Place the switch in the NEC position.
Image 3-4
Remark with RC5 protocol
Not all buttons of the Pulse RCU are one-to-one compatible with the legacy Barco RCU. Button pairs SHUTTER open/close and
POWER on/off emit the same code (per pair) when in RC5 mode, because the legacy RCU’s only had 1 button for Shutter and 1
button for Standby.
3.3 Remote control, on/off button
Purpose of the remote control on/off button
The Pulse remote control unit has at the front side an on/off switch (reference 1 image 3-5). Switching off the remote control prevents
that unwanted commands are send due to an accidental key press. Furthermore, switching the RCU off will extend the battery life
time of the remote control.
To activate the remote control press the on/off button.
To deactivate the remote control press the on/off button again.
Default when (re)placing batteries, is “ON”.
24
R5905032 HDX SERIES 23/01/2018
Page 29
3. Pulse Remote Control Unit
1
Image 3-5
3.4 Functions of the “button pressed indicator”
Functions button pressed indicator
• Rapidly flashes when commands are sent, this is the normal “button pressed” indication.
• 1 Short flash when remote control is switched ON by means of the on/off button.
• Continuously lit (up to 5 seconds) when address digits are expected after pressing the ADDR button.
•Slowlyfl ashes (2 times a second) when the battery level is becoming low; typically when more than 85% of the useful life is
past.
3.5 Displaying and Programming addresses into the RCU
Displaying the Projector Address on the Screen.
1. If the projector is on, press the menu key and navigate to the Status page. The projector address and the broadcast address can
be seen under the Communication heading.
The projector’s address is displayed on the LCD status screen and / or the OSD.
How to Program an Address into the RCU?
1. Press the Address button until the Button pressed indicator lights up continuously (proximately 5 seconds).
2. Enter the address with the digit buttons within the time the indicator lights up (also proximately 5 seconds).
Note: That address can be any value betwe en 0 and 31.
Tip: A few examples:
To enter address 3, press "3" digit button on the RCU to set the RCU’s address to 3 and wait until the button pressed
indicator is out. Alternatively, you can also press “0” and “3”. This way, the button pressed indicator goes out immediately.
To enter address 31, then press “3” and “1” on the digit button on t he RCU and the button pressed indicator goes out
immediately.
3.6 Using the XLR connector of the RCU
Connecting a cable with the XLR connector will reset the broadcast address of the RCU to its default value ’0’.
How to use the XLR connector
1. Remove the XLR cover by pulling it backwards.
R5905032 HDX SERIES 23/01/2018
25
Page 30
3. Pulse Remote Control Unit
Image 3-6
2. Connect a cable with XLR plug into the XLR connector of the RCU.
3. Connect the other end of the cable with the XLR input of the projector.
3.7 Using the mini-jack connector of the RCU
Connecting a cable with the mini-jack connector will reset the broadcast address of the RCU to its default
value ’0’.
How to use the mini-jack connector
1. Connect a cable with the mini-jack connector (reference 2 image 3-7) of the RCU.
2. Connect the other end of the cable with the mini-jack input of the projector.
2
Image 3-7
3.8 Silicone protection sleeve for the RCU (optional)
Introduction
Barcooffersasiliconeformfitting protection sleeve for the Pulse RCU. The silicone material keeps it comfortably, non slip and soft
touch. All buttons and holes remain accessible. The sleeve is quick and easy installed. For ordering information see Barco website.
How to install
1. Pull off the rubber XLR-lid from the RCU.
Image 3-8
26 R5905032 HDX SERIES 23/01/2018
Page 31
3. Pulse Remote Control Unit
2. Place back side (XLR side) of the RCU into the sleeve and pull the other side of the sleeve over the front side of the RCU.
Image 3-9
R5905032 HDX SERIES 23/01/2018 27
Page 32
3. Pulse Remote Control Unit
28 R5905032 HDX SERIES 23/01/2018
Page 33
4. Physical installation
4. PHYSICAL INSTALLATION
About this projector
This chapter describes how the mechanical set up of the projector has to be done and how to realize the electrical connections.
Overview
• Lenses
• Connecting the projector with the power net
• Alignment of a table mounted projector
• Mounting the bottom carry handler
• Mounting the top carry handler
• Suspension of the projector with rigging clamps
• Alignment of a ceiling mounted projector
4.1 Lenses
Overview
• Available lenses
• Lens selection
• Lens installation
• Lens removal
• Lens safety cable
• Lens shift, zoom & focus
• Scheimpflug adjustment
4.1.1 Available lenses
Available lenses for the HDX projector projector
The TLD HB (High Brightness) lens series can be used on the HDX projector projector.
Image 4-1
R9862000: TLD+ lens (0.73 : 1)
Image 4-2
R9801414: TLD+ zoom lens (0.8 - 1.16 : 1)
Image 4-3
R9862005: TLD+ zoom lens (1.16 - 1.49 : 1)
R5905032 HDX SERIES 23/01/2018 29
Page 34
4. Physical installation
Image 4-4
R9840776: TLD+ (1 .2 : 1) fixed lens
Image 4-7
R9862030: TLD+ zoom lens (2.8 - 4.5 : 1)
Image 4-5
R9862010: TLD+ zoom lens (1.5 - 2.0 : 1)
Image 4-8
R9862040: TLD+ zoom lens (4.5 - 7.5 : 1)
4.1.2 Lens selection
How to select the right lens
1. Determine the required screen width (SW).
2. Determine the approximate position of the projector in the room.
3. Start up the Lens Calculator on the Barco website: h
configuration.
The Lens Calculator window opens.
Image 4-6
R9862020: TLD+ zoom lens (2.0 - 2.8 : 1)
Image 4-9
R9829997: TLD+ zoom lens (7.5 - 11.0 : 1)
ttps://lenscalculator.barco.com/ to determine the possible lenses for your
Image 4-10
Lens calculator
30 R5905032 HDX SERIES 23/01/2018
Page 35
4. Physical installation
The Lens Calculator can also be used to determine the position of the projector when the lens type and screen
width is known.
Due to lens tolerances the results of calculated values may be different from measured values. These difference may vary +/- 5%.
4.1.3 Lens installation
How to install
1. Remove the foam rubber in the opening of the lens holder if not removed yet.
2. Take the lens assembly out of its packing material and remove the lens caps on both sides.
3. Place the lens holder in the “unlocked” position by moving the lens lock handle (A) towards the lens power supply socket (B) as
illustrated.
B
A
Image 4-11
Lens installation, preparation
4. Ensure that the lens holder stands in the On-Axis position (horizontal and vertical mid position).
Note: The lens holder is placed default in the O n-Axis po sition at factory.
5. Gently insert the lens in such a way that the lens connector matches the socket (B).
Image 4-12
Lens insertion
6. Insert the lens until the connector seats into the socket.
Warning: Do not release the Lens yet, as the Lens may fall out of the Lens Holder.
R5905032 HDX SERIES 23/01/2018
31
Page 36
4. Physical installation
7. Secure the lens in the lens holder by sliding the lens lock handle into the “locked” position, which is away from the lens power
supply socket. Ensure the lens touches the front plate of the lens holder.
Image 4-13
Lock lens
8. Check if the lens is really secured by trying to pull the lens out of the lens holder.
CAUTION: Never transport the projector with a Lens mounted in the Lens Holder. Always remove the Lens
before transporting the projector. Neglecting this can damage the Lens Holder and Prism.
4.1.4 Lens removal
How to remove
1. Support the lens with one hand while you unlock the lens holder by sliding the lock handle towards the “unlocked” position as
illustrated.
Image 4-14
Lens removal, unlock
2. Gently pull the lens out of the lens holder.
Image 4-15
Lens removal
32 R5905032 HDX SERIES 23/01/2018
Page 37
4. Physical installation
It’s recommended to place the Lens caps of the original Lens packaging, back on both sides of the removed
Lens to protect the optics of the Lens.
It’s recommended to place the foam rubber of the original projector packaging, back into the Lens opening to
prevent intrusion of dust. Note that this foam rubber is packed in a plastic bag to prevent the dust, emitted by
the foam, from entering the projector.
4.1.5 Lens safety cable
When using the safety cable ?
The lens safety cable must be used in any circumstances to protect a mounted lens in the lens holder when the projector is mounted
above persons.
Configuration differences
Therearetwodifferentconfigurations for the safety cable. The configuration used depends on the used carrying handle or hoisting
eye.
•Configuration A applies when connecting the projector to the bottom carrying handle.
•Configuration B applies when connecting the projector to the top carrying handle.
Necessary parts
• Safety Cable (750 mm, Ø3 mm)
• Cable clamp M4
• Shackle 7x70 mm
• 4 x Cable clip (16x16 mm, Ø4 mm)
How to mount the cable
1. Paste four cable clips on the lens as illustrated (reference 1). Orient the open side of the clips towards the front of the lens.
2
2
1
Image 4-16
2. Snap the first loop end of the safety cable into one of the following clips and let the loop end point downwards.
a) Configuration A: Use the upper clip on the side of the cable bundle (reference 2, image 4-16).
b) Configuration B: Use the upper clip on the non-wired side (reference 2, image 4-17).
3. Slide the rest of the cable around the lens counterclockwise. Click the cable into every clip it passes in this loop.
Note: Make sure the cable passes between the lens and the cable bundle.
4. Slide the cable through the loop end at the beginning of the cable.
Image 4-17
1
R5905032 HDX SERIES 23/01/2018
33
Page 38
4. Physical installation
Image 4-18
Example of configuration A
5. Install a U-bolt on the lens holder, with the open ends oriented outwards (reference 3). Make sure that both a part of the loop end
and the outgoing part of the safety cable are placed in the enclosure.
3
Image 4-19
Example of Configuration A
Image 4-20
Example of Configuration B
6. Close the U-bolt and tighten it.
Note: Make sure the safety cable is tightened around the lens before tightening the U-bolt nuts.
7. Place the shackle through the free loop end of the safety cable.
How to mount the cable
1. Place the lens in the lens holder, using the lens locking mechanism.
Caution: A lways make sure the lens is really secured by trying to pull the lens out of the lens holder.
2. Lead the cable end with the shackle around one of the following carrying handles:
-Configuration A: Around the bottom carrying handle.
-Configuration B: Around the top carrying handle.
3. Snap the shackle to the straight part of the cable.
4. Secure the shackle by screwing the safety ring of the shackle over the open end.
3
34
R5905032 HDX SERIES 23/01/2018
Page 39
Image 4-21
4. Physical installation
Image 4-22
Example using the top carrying handle
4.1.6 Lens shift, zoom & focus
Via Lens key
1. Press LENS key on the local keypad or the remote control.
The zoom/focus menu opens.
Image 4-23
Zoom/Focus adjustment
2. Use the ▲ or ▼ key to zoom the len
Use the ◄ or ► key to focus the lens.
Press ENTER to switch to Lens shift adjustment.
R5905032 HDX SERIES 23/01/2018
s.
35
Page 40
4. Physical installation
Image 4-24
Shift adjustment
3. Use the ▲ or ▼ key to shift the lens in vertical direction.
Use the ◄ or ► key to shift the lens in horizontal direction.
Press ENTER to switch to zoom/focus adjustment.
Via direct access keys on the remote control
1. Press LENS FOCUS button [-] or [+] (C) for an overall focus of the image.
2. Press ▲ LENS SHIFT ▼ button for correct vertical position of the image on the screen.
3. Press ◄ LENS SHIFT ► button for correct horizontal position of the image on the screen.
Take into account that the lens focus may slightly drift while the lens is warming up from cold to operation
temperature. This is a typical phenomenon for projection lenses used with high brightness projectors. The
operation temperature of the lens is reached after approximately 30 minutes projection of average video.
4.1.7 Scheimpflug adjustment
Always use allowed and calibrated lenses for the specific projector while adjusting the Scheimplug adjustments.
What has to be done ?
The lens holder has to be adjusted so that the “sharp focus plane” of the projected image falls together with the plane of the screen
(Fp1→Fp2). This is achieved by changing the distance between the DMD plane and the lens plane (Lp1→Lp2). The closer the lens
plane comes to the DMD plane the further the sharp focus plane will be. It can sometimes happen that you won’t be able to get a
complete focused image on the screen due to a tilt (or swing) of the lens plane with respect to the DMD plane. This is also known
as Scheimpflug’s law. To solve this the lens plane must be placed parallel with the DMD plane. This can be achieved by turning the
lens holder to remove the tilt (or swing) between lens plane and DMD plane (Lp3→Lp4).
Lp1
Lp2
DMD
Image 4-25
Scheimpflug principle
Scheimpflug principle
The "plane of sharp focus" can be changed so that any plane can be brought into sharp focus. When the DMD plane
and lens plane are parallel, the plane of sharp focus will also be parallel to these two planes. If, however, the lens
plane is tilted with respect to the DMD plane, the plane of sharp focus will also be tilted according to geometrical and
optical properties. The DMD plane, the principal lens plane and the sharp focus plane will intersect in a line below the
projector for downward lens tilt.
SCREEN
Fp1
Fp2
DMD
Lp3
Lp4
(Scheimpflug)
Fp4
Fp3
SCREEN
36 R5905032 HDX SERIES 23/01/2018
Page 41
Scheimpflug adjustment points
A
a
B
4. Physical installation
b
1
4
C
d
D
Image 4-26
Scheimpflug adjustments
Indication on drawing Function
4 Locking nut
1, 2 and 3 Scheimpflug adjustment nuts
A, B, C and D Set screws
a, b, c and d lock nuts
1, 2 and 3 are adjustment points.
4 is a locking point and NOT used during Scheimpflug adjustment.
2
3
c
Necessary tools
• Allenkey3mm
• Nut driver 13 mm
• Nut driver 10 mm
How to adjust
1. Project a green focus pattern.
Image 4-27
2. Loosen the lock nuts (a, b, c and d). See image 4-26.
3. Loosen the 4 set screws (A, B, C and D) by 1 cm. See image 4-26.
4. Fully loosen lock nut 4. See image 4-26.
R5905032 HDX SERIES 23/01/2018
37
Page 42
4. Physical installation
5. Optimize the focus of the projected image as follows:
a) Place the zoom lens in TELE position (smallest projected image) and adjust the focus using the lens focus barrel or motorized
focus control.
b) Place the zoom lens in WIDE position (largest projected image) and adjust the focus by turning equally on nut 1, 2 and 3.
c) Repeat steps “a” and “b” until the projected image is as sharp as possible.
F
1
Image 4-28
Center focusing
6. Sharpen bottom left corner of the screen by adjusting nut 1.
2
3
F
Image 4-29
Left bottom focusing
7. Sharpen bottom right corner of the screen by adjusting nut 2.
38
1
R5905032 HDX SERIES 23/01/2018
Page 43
Image 4-30
Right bottom focusing
8. Sharpen top right corner of the screen by adjusting nut 3
4. Physical installation
F
2
F
3
Image 4-31
Corner focusing
9. Repeat from step 6 until the projected focus pattern is as sharp as possible in the center, left, right, top and bottom of the screen.
How to fixtheScheimpflug
Start the fixation as follows (steps must be followed strictly) :
1. Turn in set screw A, B and C. Tighten lightly (by hand).
Tip: Any movem ent of the im age will affect the S cheimp flug adjustment
2. Fasten lock nuts a, b and c.
3. Turn in set screw D lightly (by hand) allowing the image to move slightly (1/3 to 1/2 of a square).
R5905032 HDX SERIES 23/01/2018
39
Page 44
4. Physical installation
Image 4-32
4. Fasten lock nut d.
5. Tighten nut 4 until the offset of the image movement created in step 3 is canceled.
Tip: The amount of image movement in step 3 w ill determine how tight the nut in step 5 will need to be turned to return the
image to its original position.
4.2 Connecting the projector with the power net
1/3 to 1/2
CAUTION: Use only the power cord provided with the projector.
How to connect with local power net
1. Ensure that the power switch stands in the ’0’ (OFF) position (1).
1
2
3
Image 4-33
Power input
2. Connect the female side of the power cord with the power input socket of the projector (2).
3. Secure the power plug by locking the plug holder clamp (3).
40
R5905032 HDX SERIES 23/01/2018
Page 45
4. Physical installation
4. Connect the male side of the power cord to the local power net.
Caution: E nsure that the power net meets the power requirements of the projector.
WARNING: Do not attempt operation if the AC supply and cord are not within the specified voltage and power
range.
CAUTION: Once the projector is switched to standby, the lamp cooling fans will continue to run for approx-
imately five minutes to ensure that the projector and lamp have sufficiently cooled, at which point the fans
will automatically decrease to standby. To avoid thermal stress that can lead to premature lamp failure, never
unplug the power cord while the lamp cooling fans are running. Never unplug the power cord to power down
the projector, first switch off the power switch and then unplug the power cord.
Fuses
The projector is protected with an automatic circuit breaker of 20 A which is built into the power sw
The voltage meter is protected with a fuse (1A) which is located on the neutral bonding cable. If necessary to replace this fuse,
consult a service technician.
itch.
4.3 Alignment of a table mounted projector
How to align
1. Place the projector in the desired location. Take into account the zoom range of the used lens and the size of the screen.
2. Project one of the internal hatch patterns on the screen.
3. Turn the adjustable feet in or out until the projected hatch pattern has a perfect rectangle shape and is leveled.
Image 4-34
Level alignment
When this is achieved, the projector is set horizontal and vertical at right angles to the screen.
SCREEN
Image 4-35
Angle adjustment
4.4 Mounting the bottom carry handler
Necessary tools
Open wrench 17 mm
Necessary parts
4x bolt M10 x 16 mm
R5905032 HDX SERIES 23/01/2018
SCREEN
41
Page 46
4. Physical installation
How to mount
1. Turn the projector upside down.
2. Turn out the 4 feet.
Image 4-36
Remove feet
3. Turn out the feet of the carry handle as far as possible.
Image 4-37
Mount carry handle
4. Place the carry handle on the projector as illustrated. Adjustment knob to the back of the projector.
Make sure that the mounting holes matches the holes in the projector.
5. Insert a bolt in each corner and turn in these bolts.
42
R5905032 HDX SERIES 23/01/2018
Page 47
2
1
Image 4-38
Insert bolts
4.5 Mounting the top carry handler
Purpose
This carry handle can be used to transport the projector in an easy way.
4. Physical installation
Necessary tools
8 mm Allen wrench
Necessary parts
• 4x bolt M10 x 16
• 4x washer
• 1x carry handler
How to mount
1. Place the carry handle on top of the projector so that the fixation holes match the holes in the projector.
1
1
Image 4-39
top carry handle
2. Turn in the 4 fixation bolts (1)
R5905032 HDX SERIES 23/01/2018 43
. Insert a washer between the bolt and the carry handle.
Page 48
4. Physical installation
4.6 Suspension of the projector with rigging clamps
Rigging points and rigging clamps
When a carrying handle is mounted at the bottom side of the projector, eight slots are available to mount rigging clamps. Four slots
are longitudinally (1) oriented and four slots are transversely (2) oriented. Each slot contains a rigging point of which the position in
the slot can be adjusted depending on the size of the truss installation. The rigging clamps can be attached to those rigging points,
which allows an easy and fast physical setup of the projector in a hanging confi guration.
1
2
Image 4-40
Rigging points
Necessary tools
• Open end spanner 24 mm
• Open end spanner 17 mm
Necessary parts
4 rigging clamps
How to install and use the rigging clamps
1. Measure the distance, center tube as reference, between the two used support bars of the truss.
X mm
Image 4-41
Truss, example
2. Turn the projector upside down and slide the rigging points on there place in the slots, according the measured distance and
secure this position. To release the nuts of the rigging points use a 24 mm open ended spanner. Ensure that the rigging points
are symmetrically lined up, so that the projector will hang in balance.
Warning: Be careful while working with heavy loads.
Warning: Always s ecure the rigging points after adjustment.
X mm
Image 4-42
Rigging points, distance
44 R5905032 HDX SERIES 23/01/2018
Page 49
4. Physical installation
3. Turn in the rigging clamps into the rigging points using a 17 mm open ended spanner and secure the rigging clamps by turning
the safety nut on the rigging clamp against the rigging point using a 17 mm open ended spanner.
Image 4-43
Mount rigging clamps
Warning: Always use four (4) rigging points, equally spread, to suspend the projector.
4. Place all four rigging clamps in open position.
5. Place the projector (upside down) under the truss installation and lower the truss until the support bars of the truss are nearby
the rigging clamps mounted on the projector.
Image 4-44
Mount to truss
6. Lift up the projector and hook the four rigging clamps over the support bars of the truss.
R5905032 HDX SERIES 23/01/2018
45
Page 50
4. Physical installation
7. Lock all four rigging clamps by turning the fixation handle clockwise.
Image 4-45
Clamp fixation
8. Install the 2 safety cables, one on both sides of the carrying handle, and around the truss.
Mount the 2 safety cables around the carry handle (push the hook through the loop and then aroun
to much play (maximum 20 cm). If necessary turn the cable a few times around the truss before clasping the safety hook around
the cable.
d the truss so that there is not
Image 4-46
Security cables
9. Lift up the truss with the attached projector to the desired height.
Mount the 2 safety cables in such a way that when something goes wrong, the projector cannot fall more than
20 cm. If necessary, turn the cables a few times around the truss to obtain this maximum distance.
4.7 Alignment of a ceiling mounted projector
Necessary tools
17 mm open spanner
Skew adjustment
1. Turn the adjustment knob on the carry handle until the projected hatch pattern is perfectly squared.
46
R5905032 HDX SERIES 23/01/2018
Page 51
Skew
Image 4-47
Skew adjustment
Tilt adjustment with the clamps
1. Adjust both front side clamp or both back side clamps to adjust the tilting.
Always adjust by two to avoid deformation of the frame.
2. Loosen the security nut on both clamps.
3. Adjust the adjustment nuts of both clamps until the desired tilting is reached.
4. Turn the safety nut on the rigging clamp against the rigging point
4. Physical installation
R5905032 HDX SERIES 23/01/2018 47
Page 52
4. Physical installation
48 R5905032 HDX SERIES 23/01/2018
Page 53
5. Input & Communication
5. INPUT & COMMUNICATION
Overview
• Introduction
• Input source connections
• Communication connections
• Utility-Accessory Outlet
5.1 Introduction
General
The Input & Communication side of the projector consists of a button module, a dual 3G/HDSDI and DVI-I input as standard input
module and 2 free input slots. The free input slots can be used for optional modules (e.g. 5-cable input).
1
2
3
4
5
6
7
8
Image 5-1
Input & Communication connections
1 Display
2 Optional antenna for Wifi connection
3 12 V output as power supply to external equipment
4 DMX in - out
5
XLR input port for remote control
6 RS232/RS422 input port
7
Dual Link DVI-I HDCP input
8 Free input slot
9 Button module
10 Optional antenna for GSM
11 RS232/RS422 input port
12 Ethernet port
13 Status and indication LEDs
14 USB port
15 3G/Dual/HDSDI input - output
16 Free input slot
9
10
11
12
13
14
15
16
R5905032 HDX SERIES 23/01/2018
49
Page 54
5. Input & Communication
5.2 Input source connections
DVI and 3G/HDSDI input
This input module is standard delivered with the HDX projector.
DUAL LINK DVI-I HDCP
SEL
SYNC
INPUT
Image 5-2
Dual Link DVI and 3G/Dual HDSDI input
The yellow LED lights up when valid input sync is detected.
The green LED lights up when the input is selected.
DVI input specifications :
• RGB analog : up to 170 MHz.
• Single DVI : up to 165 MHz
• Dual link DVI : up to 210 MHz
DVI will not natively support 10-bit or 12-bit deep color. It is possible to enable 30-bit color over DVI using
a specific pixel packing. We support the pixel-packing that is implemented by Silicon Image Sil7189 DVI receiver.
3G/Dual HDSDI input specifications :
• 3G follows the SMPTE 425M standard.
• HDSDI follows he SMPTE 292M standard.
• Dual link follows the SMPTE 372M standard
• SDI follows the 259M standard
5-cable input (optional)
Optional multi purpose input which can be inserted in the free slots.
IN1
SEL
SYNC
3G/DUAL HDSDI
OUT1
IN2
SEL
SYNC
R9864000
OUT2
V/C
R
R9864010
SEL
SYNC
Image 5-3
BARCO
R/PR G/Y/VIDEO
5-CABLE INPUT
B/P
B
H/S
Signal connectivity
Input signal
RGBHV
RGBS
RGsB
RGBCV
Composite Video
Super Video
Component Video
R/P
R
R
R
R
R
—
—
PR/(R-Y)
G/Y/VIDEO B/ P
G
G
Gs
sync on green
G
VIDEO
Y
Luma
Y
BHV
B
B
B
———
——
PB/(B-Y) S
B
-S
Component Video
PR/(R-Y)
Ys
PB/(B-Y)
-SOY
YUV-CV R-Y Y B-Y CV
5-cable input specifications :
H/S V/C
S
R
—
——
CV
-
C
Chroma
—
——
-
50
R5905032 HDX SERIES 23/01/2018
Page 55
5. Input & Communication
• Data and HD sources RGB and YUV [HS/VS, CS or SOG(Y)]:
- Pixel clock maximum 210 MHz
- 8 bit digital output
• Video sources CVBS, S-VIDEO, RGB and YUV [CS, CV or SOG(Y)]:
- PAL B/D/I/G/H, PAL60, PAL M, PAL N, PAL Nc
- NTSC M/J, NTSC 4.43
- SECAM B/D/G/K/L
- 525i, 625i, 525p, 625p
- Macrovision copy protection robust
- Standard images “video525” and “video625”
• Automatic detection of sync inputs but with manual override:
- automatic modes : RGB, YUV, VIDEO
- manual modes : RGB HS/VS - CS, RGB CV, RGB SOG, YUV HS/VS - CS, YUV CV, YUV SOY, CVBS, S-VIDEO
• Possible to disconnect 75 Ohm terminations on HS and VS (TTL sync level selection)
• Signal requirements:
- Component Video (BNC)
o
R-Y : 0,7Vpp ±3dB 75 Ohm termination.
o
Ys : 1Vpp ±3dB (0,7V Luma +0,3V Sync) 75 Ohm termination.
o
B-Y : 0,7Vpp ±3dB 75 Ohm termination.
-RG(s)B
o
R : 0,7Vpp ±3dB 75 Ohm termination.
o
G(s) : 1Vpp ±3dB (0,7Vpp G + 0,3Vpp Sync) 75 Ohm termination.
o
B : 0,7Vpp ±3dB 75 Ohm termination.
• Diagnostic LED’s on front panel:
- Green LED: Lights up in case input module is selected
- Yellow LED: Lights up in case sync detected
3D Input Module (optional)
Optional 3D input which can be inserted in the free slots.
BARCO
3D SYNC IN
Image 5-4
Signal connectivity
• 3D SYNC IN
BNC socket to apply an external 3D synchronization signal. Used for sequential modes. If signal is not present an internal 3D
sync is generated.
• DISPLAYPORT
DisplayPort connector to connect a video source.
• DisplayPort selection LED + sync LED
SEL: lights up if the DisplayPort is selected.
SYNC: lights up if the applied source has a valid DisplayPort sync.
• HDMI
Connector for HDMI cable (with optional locking mechanism).
• HDMI selection LED + sync LED
SEL: lights up if the HDMI input port is selected.
SYNC: lights up if the applied source has a valid HDMI sync.
• 3D SYNC OUT
BNC socket. Generates 3D synchronization signal to drive an infra red transmitter for active 3D glasses. In case an 3D synchronization signal is applied on the “3D SYNC IN” for a single channel 3D stream then the generated 3D output sync is derived
from this applied sync.
Input specifications
DISPLAYPORT HDMI
3D INPUT
SEL
SYNC
SEL
SYNC
R9864140
3D SYNC OUT
R5905032 HDX SERIES 23/01/2018
51
Page 56
5. Input & Communication
• HDMI (High-Definition Multimedia Interface)
HDMI 1.4a up to 210MHz pixel clock. Support for ‘Deep Color’ up to 12 bit per color.
• DisplayPort
DisplayPort 1.1a up to 210 MHz pixel clock. Support for ‘Deep Color’ up to 12 bit per color.
In all cases, the minimum input frequency for 3D is 23 Hz per eye. Below this frequency the image will not be
displayed correctly.
5.3 Communication connections
Communication interface
DMX
IN
/1A
12V
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Image 5-5
Communication interface, indications
1 12V 1A output
2
DMX interface (input, output)
3 XLR input
4
RS232 input
5
USB port
6 Ethernet port
7
Ethernet type indication
8 Ethernet activity indication
9 Error indication
10 Power indication
11 IR indication
12 Lamp indication
13
ACT (activity) indication
14
Wifi select indication
15 IR receiver
OUT
REMOTE CTRL
1
2
3
RS232/422 IN
USB
10/100 BASE-T
ETH
ACT
10/100
PWR LMP
ERR
WIFI
SEL
IR ACT
15
12V output
12 V output, maximum 1A, available when projector is not in stand by.
DMX interface
DMX is used as communication bu
the bus can be looped between the different devices. According the standard a five wire cable with XLR connector is used.
You can use the DMX input port to connect a DMX device (DMX console) to the projector. This way you can control the projector
from that DMX device (console). The DMX output port can be connected with the next device in the loop.
Pin Description
1Earth
52
s between different devices in the light technic. Each device has an input and an output, so that
R5905032 HDX SERIES 23/01/2018
Page 57
5. Input & Communication
Pin Description
2
3Hot
4
5
DMX
DMX-512 Lighting protocol over RS-485 interface. Carries information of 512 channels from a lighting con
lighting devices. Standardized by USITT.
Cold
Return - (or not used)
Return + (or not used)
Wired remote control (XLR)
If desired the remote control unit can be wired and plugged in into the male XLR port on the communication interface.
XLR – Remote CTRL in
Pin Description
1
GND
2
RC5 in
3 XLR present sense
troller to
RS232/RS422 input
The communication interface of the HDX projector supports RS232 and RS422 serial communication on two different types of input
connectors. The left one a Sub-D connector, the right one an USBB connector acting as RS input when connected to an USB input
of a PC.
You can use the RS232/RS422 input to connect a local PC to your HDX projector. By this way you can configure and control your
HDX projector from your local PC.
Do not forget to set the projector’s baud rate to match that of the computer.
Advantages of using RS232/RS422 serial communicatio
• easy adjustment of the projector via PC (or MAC).
• allow storage of multiple projector configurations and set ups.
• wide range of control possibilities.
• address range from 0 to 255.
• sending data to the projector (update).
• copying data from the projector (backup).
RS232/422 input (Sub-D) port
Pin Description
1
DCD : Data Carrier Detect
2RXD-:ReceiveData
3 TXD- : Transmitted Data
4
DTR : Data Terminal Ready [RS232]
TXD+ : Transmitted Data [RS422]
5
GND : Ground
6
DSR : Data Set Ready [RS232]
RXD+ : Received Data [RS422]
7
— (not connected) —
8
CTS : Clear To Send
9 RI : Ring Indicator
n:
R5905032 HDX SERIES 23/01/2018
53
Page 58
5. Input & Communication
RS232
An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the communication path between two devices using either D-SUB 9 pins or D-SUB 25 pins connectors. This standard is used for
relatively short-range communications and does not specify balanced control lines. RS-232 is a serial control standard
with a set number of conductors, data rate, word length and type of connector to be used. The standard specifies component connection standards with regard to computer interface. It is also called RS-232-C, which is the third version
of the RS-232 standard, and is functionally identical to the CCITT V.24 standard. Logical ’0’ is > + 3V, Logical ’1’ is < 3V. The range between -3V and +3V is the transition zone.
RS422
An EIA serial digital interface standard that specifies the electrical characteristics of balanced (differential) voltage,
digital interface circuits. This standard is usable over longer distances than RS-232. This signal governs the asynchronous transmission of computer data at speeds of up to 920,000 bits per second. It is also used as the serial port
standard for Macintosh computers. When the difference between the 2 lines is < - 0.2V that equals with a logical ’0’.
When the difference is > +0.2V that equals to a logical ’1’..
USB port
The communication interface is equipped with a master USB port, type “A” connector. This USB port will simplify the service procedures for software updates or for taking backup files from the projector without network connection. An USB-stick is plugged into
the USB port and files can be transferred from or to the projector using the local or remote control unit. Note that the USB-stick has
to be Linux FAT16 compatible.
Ethernet port
The projector can be connected to a LAN (local area network) using the Ethernet port on the communication interface. Once connected to the LAN, users are capable of accessing the projector from any location, inside or outside (if allowed) their company
network using the control software: Projector Toolset. This toolset locates the projector on the network in case there is a DHCP
server or the user can insert the correct IP-address of the projector to access the projector. Once accessed, it is possible to check
and manipulate all the projector settings. Remote diagnostics, control and monitoring of the projector can then become a daily and
very simple operation. The network connectivity permits to detect potential errors and consequently improve the time to servicing.
The connector used for the Ethernet ports (E) are of rugged Neutrik EtherCon RJ45 type, which is compatible
with standard RJ45 cable connector. Straight (most common) as well as cross linked network cables can be
used.
10/100 Base-T — RJ45 port
Pin Description
1TXD+
2TXD-
3RXD+
4
5
6RXD-
7
8
—
—
—
—
Status lights
Function Color Description
ETH act
10/100
IR red IR received but not acknowledged
WIFI sel
ACT
ERR red See chapter “Getting started”, topic “Status LEDs”
green
orange
green
orange
green
When connected with an Ethernet
When a 100 MB network is detected
IR received and acknowledged
When WiFi is selected
When WiFi is connected with an Ethernet
54
R5905032 HDX SERIES 23/01/2018
Page 59
5. Input & Communication
Function
PWR
LMP
Color
orange
orange
Description
See chapter “Getting started”, topic “Status LEDs”
See chapter “Getting started”, topic “Status LEDs”
5.4 Utility-Accessory Outlet
What can be done ?
An extra DMX controlled accessory can be added to projector.
Some examples of the use of this connector:
• Connect external accessories like the Catalyst Mirrorhead (Even if this example still needs a extra Power supply
• Connect other DMX enabled devices like, color changers, shutters, dimmer wheels
• Connect a DMX Lens option
• Connect a DMX rigging frame level device
• Use for external relay
Image 5-6
Utility-accessory outlet
Pin configuration
1
GND
2DMXData–
3DMXData+
4
Power 9 - 24 Volt DC With Setting in menu 9 / 12 / 24 @ 25W
Note : do not overload ! Maximum 1A on 24V is allowed.
The connector is a duplicated output of the DMX signal entering the projector over the 5 Pin XLR
R5905032 HDX SERIES 23/01/2018
55
Page 60
5. Input & Communication
56 R5905032 HDX SERIES 23/01/2018
Page 61
6. GETTING STARTED
Overview
• RCU & Local keypad
• Terminology overview
• Power on projector
• Switching to standby
• Power off projector
• Status LEDs
• Using the RCU
• Projector Address
• Source selection
6.1 RCU & Local keypad
How controlling the projector ?
The projector can be controlled by the local keypad or by the remote control unit.
Location of the local keypad ?
The local keypad is located on the input side of the projector.
6. Getting started
Remote control functions.
This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This
remote control is used for source selection, control, adaptation and set up.
Other functions of the remote control are :
• switching between stand by and operational mode.
• switching to "pause" (blanked picture, full power for immediate restarting)
• direct access to all connected sources.
6.2 Terminology overview
Overview
The following table gives an overview of the different functionality of the keys.
R5905032 HDX SERIES 23/01/2018
57
Page 62
6. Getting started
23
1
5
1
(
7
7
%
*
$
3
2
5
3
,
3
:
2
'
1
,
:
22
21
20
10
2
1
6
7
RGB
PATTERN
STBY
PAUSE TEXT
7
2
Image 6-1
Local keypad and RCU
61
4
3
89
WINDOW
PIP
AUTO
2016
3
MENU
EXIT
4
10
11
5
TEXT
PHASE
SHARPN
TINT
COLOR
BRIGHTN
CONTR
LENS
SHIFT
LENS
SHIFT
ENTER
6
LENS
7
8
9
PAUS E
*
*
$
1
,
*
*
,
5
(
0
,
2
7
8
$
0
9
8
7
6
5
3
4
2
1
LENS
ZOOM
LENS
FOCUS
19
EXIT
5
3 18
MENU
0
LENS
FN
821
9
ENTER
5
17
19
18
17
16
15
14
13
12
Ind. Key name Description
1 Pattern key Direct access key to the internal pattern selection menu.
2 RGB Toggle key to enable and disable colors in the adjustment mode. Toggle between red,
green, blue and full RGB.
3 MENU Access key to the menu structure and key to quickly quit the adjustment menus.
4 Address key (recessed key), to enter the address of the projector (between 0 and 9) in the remote
control. Press the recessed address key with a pencil, followed by pressing one digit
button between 0 and 9.
5
LENS
Direct access key to the lens adjustment menus. Toggling this key will change the
projected pattern.
6
PAUSE To stop projection for a short time, press ’PAUSE’. The image disappears but full power
is retained for immediate restarting. Shutter is closed.
7
STBY Standby function switch off the lamp and lamp electronics. The lamp cooling fans remain
active for about 5 minutes. The speed of the other fans is reduced.
8F
N
9Auto
FN toggles the local display to preview an input
Auto alignment at first access.
10 Digit buttons Direct input selection or numeric entries
11
Lens zoom/focus Zoom and focus controls of the lens
12
Lens shift Shift control of the lens, to shift the lens up/down or left/right
13 Picture controls Use these buttons to obtain the desired picture level.
14
PHASE Used to remove the horizontal instability of the image (usually for RGB source). It adjusts
the phase of the pixel sampling clock relative to the incoming signal.
15 FREEZE
To freeze the actual projected image.
58
R5905032 HDX SERIES 23/01/2018
Page 63
6. Getting started
Ind. Key name Description
16 TEXT Toggle key to activate or deactivate on screen text boxes while adjusting a setting.
When adjusting one of the image controls, e.g. during a meeting, the normally displayed
bar scale can be deactivated by pressing ’TEXT’ key first. To re-display the bar scale
on the screen, press ’TEXT’ key again. When TEXT is ’off’, no adjustment menu’s
will be displayed on the screen when entering the adjustment mode. All menus and
adjustments remain active on the local LCD panel.
17 ENTER
18
Cursor keys
19 EXIT Key to go one menu stage higher than the actual position when in the adjustment mode.
20
WINDOW Selection of the active window “Main” or “PiP”
21 PIP
22
Info Displays help information when on a certain menu item of the sofrware
23
RC Operating indication Lights up when a button on the remote control is pressed. (This is a visual indicator to
Ta bl e 6 -1
Key to confirm an adjustment or selection in the adjustment mode.
To make menu selections when in the adjustment mode
Direct access key for picture in picture selection.
check the operation of the remote control)
6.3 Power on projector
How to power on.
1. Press the power switch at the back of the projector to switch on this projector.
Image 6-2
Main switc h
- When ’0’ is pressed, the projector is switched off.
- When ’1’ is pressed, the projector is switched on.
The projector starts up in standby. The menus are accessible via the local LCD panel.
The start up screen is displayed on the local LCD panel and when fully started up, it changes to the overview screen.
R5905032 HDX SERIES 23/01/2018
59
Page 64
6. Getting started
Image 6-3
Start up screen, Main
This screen indicates :
- the selected Main input
- the selected PIP input
- the IP address
- the Customer Id
- the Lamp status
- the Mains voltage
- the current ambient temperature
- the Text status (OSD)
To display an image, the standby key must be pressed once.
The current mains input voltage is indicated on the voltmeter just above the power switch.
The background image of the startup screen and info screens can be changed with Projector Toolset with an
installed HDX plug-in.
Lamp overview
Once the projector is started, press Lamp to get an overview of the lamp parameters such as :
Image 6-4
Local screen, lamp
60 R5905032 HDX SERIES 23/01/2018
Page 65
6. Getting started
• number of Strikes
• Run time in hours
• Remaining run time in hours
• slide bar indication with percentage indication of the current run time, compared with the maximum life time of the lamp.
Software overview
Once the projector is started, press About to get an overview of the software versions such as :
Image 6-5
Local screen, about
• Package version
•Mgrsoftware
• GUI software
Starting image projection via the standby key.
1. Press Stand by key once on the local keypad or on the remote control.
R5905032 HDX SERIES 23/01/2018 61
Page 66
6. Getting started
5
1
3
,
3
:
2
'
1
,
:
(
7
7
%
*
$
3
5
3
2
1
6
RGB
STBY
Image 6-6
Standby key indication
7
PATTERN
PAUS E
89
WINDOW
TEXT
AUTO
MENU
LENS
PAUSE
*
*
$
1
(
,
0
,
*
2
4
5
MENU
EXIT
0
PIP
LENS
Fn
ENTER
*
,
7
5
8
$
0
9
8
7
6
5
3
4
2
1
LENS
ZOOM
LENS
FOCUS
TEXT
PHASE
SHARPN
TINT
COLOR
BRIGHTN
CONTR
LENS
SHIFT
LENS
SHIFT
EXIT
ENTER
The projector starts up on the last saved source. The LMP LED on the communication interface lights up.
Some lamp and runtime warnings can be displayed when an image is displayed after a start up.
6.4 Switching to standby
How to switch to standby
1. Press and hold Standby for 3 seconds on the local keypad or the remote control. In the mean time the message Keep on
pressing... is displayed. This message changes to Saving data ...
The projector goes to standby.
All custom settings are written to the internal backup device. A message ’Saving data ...’ indicates this
process. Never switch off the projector while this message is displayed.
When switching to standby, an after cooling process will start to cool down the projector. The after cool time
depends on the temperature inside the projector and can vary from 30 second to 5 minutes.
6.5 Power off projector
How to power off
1. Press fi rst Standby.
2. Let cool down the projector until the fan speed decreases. At least 5 minutes.
3. Switch off the projector with the power switch. ’0’ must be pressed.
62
R5905032 HDX SERIES 23/01/2018
Page 67
CAUTION: Never switch off the projector while the message ’Saving data ... ’ is displayed !
6.6 Status LEDs
Overview
LED
Standby button
Pause button
PWR (power
LED)
LMP (lamp
LED)
ERR (error
LED)
Color status
Red on Projector is in standby
Red toggles on/off Projector startup failed, no lamp power supply
Green toggles on/off
Green on
Orange toggles on/off Projector is on, lamp power supply is off
White toggles on/off From/To ECO standby
Dimmed white Projector powers up
Red on
Green on Shutter is open
Dimmed white
Full white
Full white toggles
on/off
Off Projector powers up
Red Standby
Orange ECO standby
Green Projector is on
Off Lamp is off
Red No lamp inserted
Orange Lamp is on in ECO mode
Green Lamp is on in normal mode
Green-Orange Lamp is on in CLO mode
Off No error
Red toggles on/off Error
Orange toggles on/off Warning
Red IR signal receivedIR
Green IR signal acknowledged
6. Getting started
Description
Projector starts up
Projector is on
Shutter is closed
Shutter is closed, projector in standby
Shutter is undefined (shutter not open and not closed)
Shutter is closed during reset formatter
6.7 Using the RCU
Pointing to the reflective screen
1. Point the front of the RCU to the reflective screen surface.
R5905032 HDX SERIES 23/01/2018
63
Page 68
6. Getting started
F1
AD
J
F2
90
PA
F3
7
US
5
E
34
1
F4
8
6
TR
EB
BA
2
LE
TE
SS
F5
XT
EX
PH
IT
SH
EN
AS
AR
TE
E
TI
CO
R
PN
NT
BR
LO
IG
CO
BA
R
HTN
NTR
LA
VO
NC
L
E
Image 6-7
IR control via reflective screen
Hardwired to the XLR input
1. Plug one end of the remote cable in the connector on the bottom of the RCU.
2. Plug the other end in the big connector on the communication interface of the projector, labelled Remote CTRL.
Note: Plugging the remote control will switch the broadcast a d dress of the remote control to the d efault value ’0’. This is the
only broadcast address that will work when hardwired. If you want to change the broadcast address after disconnecting
the remote control.
Pointing directly to the IR sensor
When using the wireless remote control, make sure you are within the effective operating distance (30 m, 100 ft in a straight line).
The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote
control unit and the projector IR sensor.
45°
Image 6-8
RCU to one of the IR sensors
45°
F3
F2
F4
F1
F5
AD
J
EX
IT
EN
TER
PA
US
E
TE
XT
PH
AS
E
90
SH
AR
PN
7
8
TI
NT
6
5
CO
LO
R
34
BR
IG
HT
N
2
1
CO
NT
R
TR
EB
LE
BA
LA
NC
E
BA
SS
VO
L
45°
45°
F3
F2
F4
F1
F5
AD
J
EX
IT
EN
TER
PA
US
E
TE
XT
PH
AS
E
90
SH
AR
PN
7
8
TI
NT
6
5
CO
LO
R
34
BR
IG
HT
N
2
1
CO
NT
R
TR
EB
LE
BA
LA
NC
E
BA
SS
VO
L
45°
45°
F3
F2
F4
F1
F5
AD
J
EX
IT
EN
TE
R
PA
US
E
TE
XT
PH
AS
E
90
SH
AR
PN
7
8
TI
NT
6
5
CO
LO
R
34
BR
IG
HT
N
2
1
CO
NT
R
TR
EB
LE
BA
LA
NC
E
BA
SS
VO
L
64 R5905032 HDX SERIES 23/01/2018
Page 69
6.8 Projector Address
6.8.1 Displaying and Programming addresses into the RCU
Displaying the Projector Address on the Screen.
1. Press Address key (recessed key on the RCU) with a pencil.
The projector’s address is displayed on the local LCD screen.
To continue using the RCU with that specific address, it is necessary to enter the same address with the
digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the
Address key displays projector address 3, then press "3" digit button on the RCU to set the RCU’s address
to match the projector’s address. Do not press 03. This will address the remote control to ’0’ and control all
projectors in the room. If the address is not entered within 5 seconds, the RCU returns to its default address
(zero address) and controls all projectors in the room.
How to Program an Address into the RCU?
1. Press the Address key (recessed key on the RCU) with a pencil.
2. Enter the address with the digit buttons within 5 seconds after pushing the address key.
Note: That address can be any digit between 0 and 9.
The LED on the remote control must lit up while pressing a digit key. Otherwise the address is not entered in
the remote control.
6. Getting started
6.8.2 Controlling the projector
Projector address
Address installed in the projector to be individually controlled.
Common address
Projector will always execute the command coming from a RCU programmed with that common address.
Why a projector address ?
As more than one projector can be installed in a room, each projector should be separately addressable with an RCU or computer.
Therefore each projector has its own address.
Set up an individual Projector Address.
The set up of a projector address can be done via the software. See chapter ’Projector Control’, ’Projector address’.
Projector controlling.
Every projector requires an individual address between 0 a
When the address is set, the projector can be controlled now:
• RCU for addresses between 0 and 9.
• computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255.
nd 255 which can be set in the Service mode.
Common Address
Every projector has a common address ’0’ or ’1’. The c
address → Common address.
hoice between ’0’ and ’1’ can be selected in P rojector Control → Projector
6.9 Source selection
Source selection when no picture in picture is active
Use the digit keys on the remote control or local keypad to activate the desired source.
R5905032 HDX SERIES 23/01/2018
65
Page 70
6. Getting started
Source selection when picture in picture is active
Use the Window button on the remote control or the local keypad to select the main window or the picture in picture (PiP) window.
5
1
3
,
3
:
2
'
1
,
:
(
7
7
%
*
$
3
5
3
2
1
6
RGB
STBY
Image 6-9
Window selection button
7
PATTERN
PAUS E
89
WINDOW
TEXT
AUTO
MENU
LENS
PAUSE
*
*
$
1
(
,
0
,
*
2
4
5
MENU
EXIT
0
PIP
LENS
Fn
ENTER
*
,
7
5
8
$
0
9
8
7
6
5
3
4
2
1
LENS
ZOOM
LENS
FOCUS
TEXT
PHASE
SHARPN
TINT
COLOR
BRIGHTN
CONTR
LENS
SHIFT
LENS
SHIFT
EXIT
ENTER
The outline of the selected window gets a colored rectangle to indicate the selection. For the main window, the color is blue. For the
picture in picture window, the color is orange.
Once the desired window is activated (main window or picture in picture window) all keys on the remote control or local keypad can
now control that selected window.
To select the source for the picture in picture window, press Window button until PiP window is activated and then select the desired
source with the digit keys.
To select the source for the main window,
press Window button until the main window is activated and then select the desired source
with the digit keys.
66
R5905032 HDX SERIES 23/01/2018
Page 71
7. Quick set up adjustment
7. QUICK SET UP ADJUSTMENT
Overview
• Text boxes ON or OFF
• Quick Lens Adjustment via LENS key
• Direct Lens Adjustment (RCU)
• Quick picture in picture
• Quick language selection
7.1 Text boxes ON or OFF
Text toggle function
The on-screen text boxes can be switched OFF so that an adjustment during the operation of the projector is not visible on the
screen. The adjustment indication remains visible on the local LCD screen.
4
PIP
AUTO
5
0
LENS
FN
1
MENU
EXIT
ENTER
1
1
6
RGB
STBY
Image 7-1
Text button
2
7
PATTERN
PAUSE TEXT
3
89
WINDOW
To toggle Text ON or OFF, press the TEXT key on the remote control or local keypad.
7.2 Quick Lens Adjustment via LENS key
Quick zoom/focus adjustment
1. Press the LENS key on the remote con
trol or local keypad to open the Zoom/Focus Adjustment menu.
*
5
MENU
5
1
(
7
7
%
$
3
PAU SE
*
$
(
0
,
2
7
8
$
LENS
3
,
3
TEXT
PHASE
2
'
1
,
:
EXIT
ENTER
:
R5905032 HDX SERIES 23/01/2018 67
Page 72
7. Quick set up adjustment
4
3
2
1
6
RGB
STBY
7
PATTERN
PAUSE TEXT
89
WINDOW
PIP
AUTO
5
0
LENS
FN
MENU
EXIT
ENTER
*
5
MENU
5
1
(
7
7
%
$
3
3
,
3
1
,
'
:
EXIT
:
2
Image 7-2
Lens button
Image 7-3
Zoom/Focus adjustment
1
1
PAU SE
*
$
(
0
,
2
7
8
$
2. Use the ▲ or ▼ key to zoom and ◄ or ► key to focus the image.
3. When finished, press EXIT key to return or ENTER to continue to the shift adjustment.
Press the LENS key to call the list with available test patterns.
LENS
ENTER
TEXT
PHASE
Quick shift adjustment
1. Press the LENS key on the remote control or local keypad to open the Z oom /Focus Adjustment menu.
Image 7-4
Zoom/Focus adjustment
2. Press ENTER to go to the Shift menu.
68
R5905032 HDX SERIES 23/01/2018
Page 73
7. Quick set up adjustment
Image 7-5
Shift adjustment
3. Use the ▲ or ▼ key to shift the lens in vertical direction.
Use the ◄ or ► key to shift the lens in horizontal direction.
Press ENTER to switch to zoom/focus adjustment.
7.3 Direct Lens Adjustment (RCU)
Lens adjustment buttons on the Remote Control
On the Remote Control four buttons with double action are provided, allowing direct alignment for lens ZOOM, FOCUS, HORIZONTALSHIFTandVERTICALSHIFT.
1. Press LENS ZOOM button [-] or [+] (A) for correct image size on the screen.
2
1
CONTR
LENS
SHIFT
LENS
SHIFT
B
D
Image 7-6
Direct lens adjustment keys
AZoom
B Vertical shift
CFocus
D Horizontal shift
A
C
LENS
ZOOM
LENS
FOCUS
2. Press LENS FOCUS button [-] or [+] (C) for an overall focus of the image.
3. Press ▲ LENS SHIFT ▼ button for correct vertical position of the image on the screen.
4. Press ◄ LENS SHIFT ► button for correct horizontal position of the image on the screen.
7.4 Quick picture in picture
Quick On - Off
Press on the PIP key on the remote control or the local keypad to activate the Load layout window.
Use the ▲▼key to scroll to the desired layout and press ENTER to activate.
Select Main full screen to switch off PIP.
R5905032 HDX SERIES 23/01/2018 69
Page 74
7. Quick set up adjustment
Image 7-7
Load layout file list
7.5 Quick language selection
Quick language selection via the remote control
When no OSD menu is visible on the screen, press the Info button (1) on the remote control.
1
5
%
*
5
Image 7-8
Info button
The language selection menu is displayed on the screen.
Select the desired language with the ▲▼key and press ENTER to activate. The current active language is indicated with a selected
radio button
$
MENU
3
1
(
7
7
3
,
3
2
'
1
,
:
EXIT
ENTER
:
Image 7-9
Language selection
Language selection via OSD
1. Press Menu to activate the menus and select Projector Control → Change Language.
70
R5905032 HDX SERIES 23/01/2018
Page 75
2. Press ENTER to open the language selection menu.
3. Select the desired language with the ▲▼key and press ENTER to activate.
The current active language is indicated with a selected radio button
Image 7-10
Main menu, projector control
Image 7-11
Projector control, change language
7. Quick set up adjustment
Image 7-12
Language selection
R5905032 HDX SERIES 23/01/2018 71
Page 76
7. Quick set up adjustment
72 R5905032 HDX SERIES 23/01/2018
Page 77
8. Start up of the adjustment mode
8. START UP OF THE ADJUSTMENT MODE
Overview
• About the adjustment mode
• About the use of the remote control and the local keypad
• Start up the adjustment mode
• Navigation and adjustments
• Menu memory
• Shortcut keys to the menus
• Test patterns in adjustment mode
• Help information in adjustment mode
8.1 About the adjustment mode
Overview
As the adjustment mode is the central place to control and align the projector, the following functions can be done:
• Input setup: different Input settings can be adjusted such as specific input slot settings, locking, native resolution and no signal
settings.
• Image adjustment: these adjustments are organized per image source and contain the aspect ratio, timings and image settings.
• Layout adjustment: set up of the main window and the picture in picture window.
• Lamp: manage the lamp mode, the lamp use, lamp type and history
• Alignment: groups all controls necessary during the setup of the projector onto a screen.
• Projector control: contains the accessibility settings of the projector, such as address and communication setup.
• Service: contains information about how the projector is performing. This information will be useful when calling for a service
intervention.
8.2 About the use of the remote control and the local keypad
Overview
All navigations and adjustments can be done either with the remote control or with the local keypad.
Almost all the keys on the remote control have an equivalent on the local keypad.
Exceptions:
• Direct adjustment keys such as Contrast, Brightness, Saturation, Phase, etc.
8.3 Start up the adjustment mode
Start up tools
To start up the adjustment mode, use the remote control or the local keypad.
How to start up?
1. Press Menu on the remote control (RCU) or on the local keypad to start up the Adjustment mode.
R5905032 HDX SERIES 23/01/2018
73
Page 78
8. Start up of the adjustment mode
The main menu of the adjustment mode opens.
Image 8-1
Main window
8.4 Navigation and adjustments
How to navigate in the menu structure?
Once in the menu structure, use the ▲ or ▼ key on the remote control or on the local keypad to scroll through the items in the
displayed menu. The selected item will get a background color. To activate a selected submenu or function, press ENTER.
When on a submenu, to return one step to the parent menu, press EXIT.
To escape the menu structure when on a menu, press MENU.
How to make an adjustment?
With the remote control or the local keypad navigate through the menu structure until the desired item is selected. Press the ▲ or
▼ key until the desired item is reached. Press EXIT to finalize the adjustment.
With the local keypad or remote control, press the ▲ or ▼ key until the desired value (setup) is reached. Press EXIT to finalize the
adjustment.
Direct adjustment within the menu:
Image 8-2
Image settings, contrast
Use the ◄ or ► key to directly adjust the current value.
or,
Via bar scale adjustment :
Once an item is selected, press ENTER to open the bar scale menu.
74
R5905032 HDX SERIES 23/01/2018
Page 79
8. Start up of the adjustment mode
Image 8-3
Contrast adjus tment
Use the ◄ or ► key to adjust the current value.
The bar scale will move accordingly.
Press EXIT to finalize the adjustment.
or,
When the bar scale is displayed, via direct input. Press ENTER to activate the input field.
Enter the desired value with the digit keys. Press ENTER to accept.
Press EXIT to finalize the adjustment.
8.5 Menu memory
Overview
Each menu with sub menus, remembers its last selected sub item even when leaving the menu structure and that as long as the
projector is running. When restarting the projector from stand-by, the menu memory is reset.
After re-opening the main menu and selecting an item, the previous selected sub item of that selected item is highlighted and can
be opened just by pressing ENTER.
8.6 Shortcut keys to the menus
About a shortcut key
The digit keys 5 to 9 can be customer programmed to directly open a pre-stored menu. That menu can be any independent menu
out of the list of menus. A menu which is built up by the content of a previous menu cannot be stored behind a shortcut.
How to use a shortcut key
While in the operational mode, no menu selected, just pre
How to create a shortcut key
Scroll to the desired menu. Press the digit key behind which the menu must be stored for 5 seconds. When the creation is successfully, a confirmation message appears on the screen. E.g. :
Image 8-4
Select Yes to confirm the creation.
To erase the shortcut, navigate to P rojector Control → Buttons.
ss on the desired digit key to open the menu behind that shortcut key.
R5905032 HDX SERIES 23/01/2018 75
Page 80
8. Start up of the adjustment mode
8.7 Test patterns in adjustment mode
Overview
When the adjustment mode is started, a test pattern can be called at any moment just by pressing the Pattern key on the RCU or the
local key path. Press as many times on the Pattern key as necessary to display the desired test pattern. The test pattern remains
on the screen as long as the adjustment mode is selected, even when selecting other menus. When leaving the adjustment mode,
the selected test pattern is cleared and the normal image is displayed again.
1
6
RGB
PATTERN
STBY
Image 8-5
Pattern button
3
2
89
7
WINDOW
PAUSE TEXT
1
4
PIP
AUTO
5
0
LENS
FN
MENU
EXIT
ENTER
1
5
*
5
MENU
%
$
3
1
(
7
7
3
,
3
2
'
1
,
:
EXIT
ENTER
:
8.8 Help information in adjustment mode
Overview
For many items in the adjustment mode, help information is available. When on an item, just click on the info button of your remote
control to display information about the selected item.
1
5
%
*
5
Image 8-6
Info button
When no information is available for the selected item, the message No help available for this item is displayed.
To return to the adjustment mode, press EXIT.
76
$
MENU
3
1
(
7
7
3
,
3
2
'
1
,
:
EXIT
ENTER
:
R5905032 HDX SERIES 23/01/2018
Page 81
9. INPUT
Overview
• Input menu overview
• Input Selection
• Advanced Settings
• Input locking
• Minimum delay
• Native resolution
• No Signal
•EDID
• 3D input
In all cases, the minimum input frequency for 3D is 23 Hz per eye. Below this frequency the image will not be
displayed correctly.
9.1 Input menu overview
9. Input
Overview table
Level 1 Level 2 Level 3 Level 4
Input
Input Selection DVI/RGB
SDI (SD/HD/3G/Dual)
Optional input 1
Optional input 2
Advanced Settings DVI/RGB
SDI (SD/HD/3G/Dual)
Input Locking Input on Main Window
Input on Pip Window
Input 1
Input 2
Input 3
Input 4
Free Run
Free Run Options
Minimum delay
Native Resolution [On/Off]
No Signal Color [black/blue]
DVI
DVI Dual link
RGB HS-VS
YUV HS-VS
AUTO
Input 1 Priority
Input 2 Priority
Input 1
Input 2
DUAL SDI
R5905032 HDX SERIES 23/01/2018
77
Page 82
9. Input
EDID
3D
Logo [On/Off]
Shutdown [Off/On]
Shutdown time
Auto dimming [On/Off]
Configure
Create
Delete
Delete All
Status
Auto Detection
Input type
Second input
Frame sequential - Single
channel
Frame sequential - Dual
channel
Frame packing (FHD3D)
Side-by-side
Top-and-bottom
SENSIO®HI-FI 3D
Line Alternating (3G)
9.2 Input Selection
How to select
1. Press Menu to activate the menus and select Input → Input Selection.
2. Press ENTER.
The Select Source menu is displayed with the actual available sources filled out.
3. Use the ▲ or ▼ key to select an input.
Image 9-1
Main window
Image 9-2
Input selection
Image 9-3
Select source
78 R5905032 HDX SERIES 23/01/2018
Page 83
9.3 Advanced Settings
Overview
• About Input Setup
• Input configuration
• DVI - RGB input
• SDI input
• 5 cable input
• HDMI - DisplayPort input (3D input module)
9.3.1 About Input Setup
Overview
Each input module must be configured before these module can be used. This configuration is necessary so that the projector knows
which type of signal is connected to its input.
The projector has 4 input slots. Slot 1 and 2 is filled up by default with a DVI and Dual SDI input. Slot 3 and 4 can be filled up with
optional input modules. Identical modules are allowed.
9.3.2 Input configuration
3D item in the Input menu is grayed out when no 3D module is inserted in slot 3 or 4.
9. Input
How to change?
1. Press Menu to activate the menus and select Input → Adv anced Settings.
2. Press ENTER.
The Advanced Settings window is displayed with the actual situation filled out.
3. Use the ▲ or ▼ key to select an input
Press ENTER to open the selection menu which will be different from input type to input type.
Image 9-4
Main window
Image 9-5
Advanced input settings
Image 9-6
Advanced settings, input selection
R5905032 HDX SERIES 23/01/2018 79
Page 84
9. Input
9.3.3 DVI - RGB input
How to select
Select DVI / RGB and press ENTER to open the selections
Image 9-7
DVI selection
The following selections are possible:
•DVI
• DVI - dual link
• RGB HS-VS/CS
• YUV HS-VS/CS
•AUTO
DVI will not natively support 10-bit or 12-bit deep color. It is possible to enable 30-bit color over DVI using
a specific pixel packing. We support the pixel-packing that is implemented by Silicon Image Sil7189 DVI receiver.
About AUTO selection
When AUTO is selected, the input source is automatically detected (only for DVI, RGB or YUV). When an analog source is detected
in AUTO mode, then the Color Space must be selected as no automatic detection is possible.
Use the ▲ or ▼ key to select the correct color space and press ENTER to select.
Image 9-8
Color space selection for AUTO
9.3.4 SDI input
About SDI input
The Dual SD/HD/3G-SDI Input can accept standard-definition (SD), high-definition (HD) and 3 Gigabit-definition serial-digital-interface (SDI) signals .
How to select
Select SDI (SD / HD / 3G / Dual) and press ENTER to open the selections
80
R5905032 HDX SERIES 23/01/2018
Page 85
Image 9-9
SDI, input type selection
The following selections are possible:
• Input 1 Priority (when 2 sources are present, the source on input 1 will have the priority)
• Input 2 Priority (when 2 sources are present, the source on input 2 will have the priority)
• Input 1
• Input 2
• Dual SDI
SDI setup
To set up the SDI input, select Setup and press ENTER.
9. Input
Image 9-10
SDI set up
First, select the standard. Use the ▲ or ▼ key to select and press ENTER to accept.
Standard :
• 4:2:2 - YCbCr-10
• 4:4:4 - YCbCr-10
•4:4:4-RGB-10
• 4:2:2 - YCbCr-12
• 4:4:4 - YCbCr-12
•4:4:4-RGB-12
Then, select the 3G setting. Use the ▲ or ▼ key to select and press ENTER to accept.
3G-A and 3G-B:
• Direct Mapping (3G-A)
• Dual HD (3G-B)
When Dual HD is selected, it is possible to use Swap links. If Swap links must be used, use the ▲ or ▼ key to select and press
ENTER to accept. The check box will be checked.
R5905032 HDX SERIES 23/01/2018
81
Page 86
9. Input
Dual HD :
• Swap links
9.3.5 5 cable input
How to select
Select 5 cable and press ENTER to open the selections
Image 9-11
Advanced settings, 5-cable
Image 9-12
5 cable configuration
Use the ▲ or ▼ key to select the desired configuration and press ENTER to select.
When e.g. CVBS/S-VIDEO AUTO is selected, the projector discovers itself which type of signal is connected to it and loads the
correct settings.
For RGB selections, advanced settings are possible. To adjust these advanced settings, use the ▲ or ▼ key to select Advanced
settings and press ENTER. The advanced settings menu opens:
Press ENTER to toggle between [Analog] and [TTL].
9.3.6 HDMI - DisplayPort input (3D input module)
How to select
Select HDMI/DP and press ENTER to open the selections
Image 9-13
HDMI-Display port selection
Use the ▲ or ▼ key to select the desired input and press ENTER to select.
9.4 Input locking
What is possible?
The output signal can be locked on an internal sync signal or on the sync signal of one of the input sources. Or it can follow the
input of the Main window or Pip window. When locked to the corresponding input sync, the output will be shown without movement
artifacts. With locking to a specific input, a set of projectors can be kept in sync, no matter what input image is shown.
Input locking is grayed out when 3D is active. Input locking is set automatically to the 3D source.
82 R5905032 HDX SERIES 23/01/2018
Page 87
How to set up
1. Press Menu to activate the menus and select Input → Input locking.
2. Press ENTER.
The Input locking window is displayed with the current selection.
3. Use the ▲ or ▼ key to select a input to lock on.
Image 9-14
Main window
Image 9-15
Input
9. Input
Image 9-16
Input locking
Input on Main window
Input on PIP window
Input 1
Input 2
Output is locked on the selected source of the main window
Output is locked on the selected source of the Pip window
Output is locked on input 1
Output is locked on input 2
Input 3 Output is locked on input 3
Input 4 Output is locked on input 4
Free run
Output is locked on an internal sync (60 Hz or manual setup)
When Input locking is set to a specific input and there is no sync signal available, the locking will be switched
to Free run without changing the user settings. Once the sync is available, it applies again the user settings.
Options for Free Run
When free run is selected, radio button selected, then the Free Run Options become available.
R5905032 HDX SERIES 23/01/2018
83
Page 88
9. Input
Image 9-17
Free run options
Use the ▲ or ▼ key to select Fixed 60 Hz or Manual and press ENTER to select.
Fixed60Hz:
Manual
locking is done on an internal sync of 60 Hz
locking is done on the indicated vertical frequency which can be changed by the user (between 24 Hz
and 60 Hz).
To change the locking frequency for Manual, use the ▲ or ▼ key to select Vert freq and press ENTER to activate.
Image 9-18
Free run, manual setting
Use the ▲ or ▼ key to change the value.
9.5 Minimum delay
Purpose
The minimum delay only affects the de-interlacing. In case of interlaced sources, the de-interlacer will be bypassed and the image
will be shown with line interpolation applied.
To ensure minimum delay in the other processing steps, make sure warping is OFF, the resolution of the input source is native and
the input locking is set to the main input.
How to toggle the delay
1. Press Menu to activate the menus and select Input → Minimum delay [On].
Image 9-19
Main menu
2. Press ENTER to toggle between [On] and [Off].
[On] : images displayed with minimum delay
[Off] : images displayed without minimum delay
Image 9-20
Input, minimum delay
84
R5905032 HDX SERIES 23/01/2018
Page 89
9.6 Native resolution
What can be done
The aim here is to always show the resolution of the source independently of the resolution of the DMD panels.
When the resolution of the source is exactly the resolution of the DMD panels, then the full content will be shown on the full DMD (A).
When the resolution of the source is higher than the resolution of the DMD panels, then only part of the image will be shown (B)
When the resolution of the source is lower than the resolution of the DMD panels, then the full image will be shown but only on part
of the DMD is used.
9. Input
Image 9-21
When the show native resolution function is in the ON position, the projector handles the source as follows:
Source Projected image
Name Ratio Resolution Ratio Resolution
XGA 4:3 1024x768 4:3 1024x768 image projected with black
SXGA 5:4 1280x1024 5:4 1280x1024 image projected with black
SXGA+ 4:3 1400x1050 4:3 1400x1050 image projected with black
UXGA 4:3 1600x1200 4:3 1600x1200 image projected with black
WUXGA 16:10 1920x1200 16:10 1920x1200 normal image projected
borders
borders
borders
borders left and right.
How to toggle to native resolution?
1. Press Menu to activate the menus and select Input → Native Resolution [On].
2. Press ENTER to toggle between [On] and [Off].
[On] : images displayed in native resolution
[Off] : images scaled to fill the complete screen
R5905032 HDX SERIES 23/01/2018
85
Page 90
9. Input
Image 9-22
Main menu
9.7 No Signal
Overview
• Background color
• Background Logo
• Shutdown settings
• Shutdown retarding time
• Auto Dimming
Image 9-23
Input, native resolution
Whatcanhappenwhennosignal
When no signal is available at the selected input, the output can be set to blue or black or a personal defined logo can be displayed
or the projector can shutdown after a certain time or auto dimming can be started.
9.7.1 Background color
How to set the background color
1. Press Menu to activate the menus and select Input → No Signal. → Color.
2. Press ENTER to toggle between [Blue] or [black].
Image 9-24
Main menu
Image 9-25
Input, no signal
86 R5905032 HDX SERIES 23/01/2018
Page 91
Image 9-26
No signal, color
9.7.2 Background Logo
What can be done ?
A logo can be switched on or off.
When logo is switched on and a logo is available, that logo will be displayed when no signal is available for the main window an no
signal available for the PiP window in case PiP is On.
How to activate logo
1. Press Menu to activate the menus and select Input → No Signal. → Logo.
2. Press ENTER to toggle between [On] or [Off].
9. Input
Image 9-27
Main menu
Image 9-29
No signal, logo
Image 9-28
Input, no signal
A dedicated logo can be loaded via Projector Toolset with a HDX plug-in installed.
9.7.3 Shutdown settings
How to change the settings
1. Press Menu to activate the menus and select Input → No Signal. → Shutdown.
R5905032 HDX SERIES 23/01/2018
87
Page 92
9. Input
Image 9-30
Main menu
Image 9-31
Input, no signal
Image 9-32
No signal, shutdown
2. Press ENTER to toggle between [On] and [Off].
[On] : projector goes in shutdown after a certain retarding time.
[Off] : projector does not go in shutdown.
9.7.4 Shutdown retarding time
About the shutdown retarding time
The retarding time is the time between no signal is detected and the moment that the projector shuts down.
How to set the retarding time
1. Press Menu to activate the menus and select Input → No Signal. → Shutdown time (min).
Image 9-33
Main menu
Image 9-34
Input, no signal
88 R5905032 HDX SERIES 23/01/2018
Page 93
Image 9-35
Shutdown Time
2. Press ENTER to toggle between [1], [3], [5] and [10] minutes.
9.7.5 Auto Dimming
About auto dimming
When no signal is detected on the selected input the lamp power will be reduced from the current value to its minimum value. When
the input signal is re-detected, the lamp power is restored to its original value.
How to set up
1. Press Menu to activate the menus and select Input → No Signal. → Auto Dimming.
9. Input
Image 9-36
Main menu
Image 9-38
No signal, auto dimming
2. Press ENTER to toggle between [On] or [Off].
[On] : when no signal, auto dimming is started.
[Off] : when no signal, no auto dimming is started.
Image 9-37
Input, no signal
R5905032 HDX SERIES 23/01/2018
89
Page 94
9. Input
9.8 EDID
EDID
Extended Display Identification Data
About EDID
The EDID file available for DVI input connectors includes timings supported by the projector; display size and other information about
the display (i.e. projector). It is the set of information that is used by digital sources connected to the projector to generate a suitable
image signal.
From the OSD, you can for each DVI input connector choose to use the Standard EDID file or create and force your custom made
EDID file. The selection of the EDID file to be used is made in the Confi gur e menu. Making your own custom EDID file(s) is done
through Create.CustomEDIDfiles can be deleted at any time.
The Standard EDID includes two timings: 1920x1200@60Hz / 1920x1080@60Hz (for HDX, HDF and APOLLO
projectors) and 2048x1080@60Hz / 1920x1080@60Hz (for HDQ projectors).
Overview
•Configure an input
• Create custom EDID file
• Delete a custom EDID file
• Delete all custom EDID file
9.8.1 Configure an input
Description
Selecting the Standard EDID file or an own created file can be selected from the list of Custom EDID files for the input.
How to configure
1. Press Menu to activate the menus and select Input → EDID → Configure.
2. Press ENTER to open the EDID configuration menu.
Image 9-39
Main menu
Image 9-40
Input, EDID
Image 9-41
EDID, configure
90 R5905032 HDX SERIES 23/01/2018
Image 9-42
EDID configuration
Page 95
Image 9-43
EDID selection list
3. Use the ▲ or ▼ key to select the input to configure.
Press ENTER to open the selection list.
The current active file is checked.
4. Use the ▲ or ▼ key to select the correct file.
Press ENTER to select this file.
Press EXIT to return to the EDID Configuration menu.
5. Use the ▲ or ▼ key to select Apply.
Your selection is applied and stored for this input.
The EDID Configuration menu remains open to configure another input.
Or,
use the ▲ or ▼ key to select OK.
Your selection is applied and stored for this input and the EDID configuration menu is closed.
9. Input
9.8.2 Create custom EDID file
Description
You can create new custom EDID files and enter the desired input timings.
How to create
1. Press Menu to activate the menus and select Input → EDID → Create.
2. Press ENTER to open the EDID creation menu.
Image 9-44
Main menu
Image 9-45
Input, EDID
R5905032 HDX SERIES 23/01/2018 91
Page 96
9. Input
Image 9-46
EDID, create
Image 9-47
EDID file creation
3. Use the ▲ or ▼ key to select Create.
Press ENTER to open the creation menu.
4. Fill out the Timings section.
Use the ▲ or ▼ key to select a setting.
Use the ◄ or ► key to change the value
or press ENTER to open the specific adjustment menu. Follow the adjustment method as described in "Navigation and adjustments", page 74.
The following timings must be entered:
- Active Pixels: horizontal resolution
- Active Lines: vertical resolution
- Frequency (Hz): amount of frames per second
5. Select the calculation method to obtain the correct (standard) video timings.
Possible selections:
- CVT: Coordinated Video Timings
- CVT RB: Coordinated Video Timings Reduced Blanking
- CVT MB: Coordinated Video Timings Minimum Blanking (not a standard)
- GTF: Generalized Timing Formula
6. Select the Options.
If necessary, scroll down to see extra options.
Select or clear the check boxes.
Image 9-48
EDID file creation, options
92 R5905032 HDX SERIES 23/01/2018
Page 97
The following options are possible:
- Stereo: this check box is currently not in use. You can leave it unchecked.
- Deep color: select this box in case of a 12 bit color signal. In this case, the Single Link pins of the DVI connector convey the
eight most significant bits, while the Dual Link pins convey the four least significant bits.
- Analog: this check box makes the selection between DVI digital or DVI analog. When checked, DVI analog is active.
7. A filename is proposed. This proposed name contains the resolution, calculation, frequency and a D or A for digital or analog.
To change the file name, select Filename and press ENTER to open the edit box.
Click inside the edit box and change the name to the desired name.
8. Select Create and press ENTER to create the new custom fi le.
9.8.3 Delete a custom EDID file
Standard EDID files cannot be deleted.
How to delete
1. Press Menu to activate the menus and select Input → EDID → Delete.
2. Press ENTER to open the EDID list with custom fi les.
9. Input
Image 9-49
Main menu
Image 9-51
EDID, delete
Image 9-50
Input, EDID
3. Use the ▲ or ▼ key to select the file which must be deleted.
Press ENTER to delete.
Image 9-52
EDID, delete list
Image 9-53
Confirmation
Aconfirmation window opens.
4. Select Ye s to delete the file and press ENTER.
R5905032 HDX SERIES 23/01/2018
93
Page 98
9. Input
9.8.4 Delete all custom EDID file
Standard EDID files cannot be deleted.
How to delete
1. Press Menu to activate the menus and select Input → EDID → Delete All.
2. Press ENTER to open the confirmation window.
Image 9-54
Main menu
Image 9-55
Input, EDID
Image 9-56
Delete All
3. Select Ye s to delete all the custom file and press ENTER.
9.9 3D input
Overview
• About 3D modes
•Activate3D
• Auto detection
• Input type selection
• 3D second input
• L-R Synchronisation, fi eld dominance
• L-R Synchronisation, Invert 3D sync out
9.9.1 About 3D modes
The mentioned menu items in the mode explanation will be explained in detail in the next topics.
Settings in the 3D menu are stored per input.
Image 9-57
Delete All, Confirm
94 R5905032 HDX SERIES 23/01/2018
Page 99
9. Input
Single 3D channel - Full resolution - sequential mode
Content is displayed by one 3D source. The frames for the left eye and right eye are displayed alternately (sequential mode).
Optional an external 3D sync can be used. The external 3D sync has to be applied to the “3D SYNC IN” port (BNC socket at the
left) of the 3D Input Module.
If two 3D Input Modules are used:
• In case a 3D Input Module is selected: use the SYNC IN of this 3D Input Module.
• In case another (DVI, SDI, 5-cable, …) input module is selected: use the SYNC IN of the first (lowest input number) 3D Input
Module.
If the external 3D sync is not available an internal 3D sync is generated by the projector. With the setting “Field dominance”the
Sync In signal can be inverted to match the left and right eye fields.
MENU > Input > 3D > L/R Synchronisation > Field Dominance [L/R] or [R/L]
Example: A DisplayPort source with a frequency of 120 Hz consisting of content for the left and right eye results in a 60 Hz video
per eye.
To activate the single channel 3D mode select:
MENU > Input > 3D > Frame S equential – Single Channel
Possible sources: DisplayPort, HDMI, dual-link DVI, 5-cable analog (up to 210 MHz), DVI analog (up to 170 MHz), SDI (up to 150
MHz).
With the “Invert 3D sync out” setting the content can be switched between the left and right eye of the user.
The “Field dominance” setting has only effect in the 3D mode: Frame sequential → Single channel (in all other
modes this setting is grayed out). Furthermore, the input frequency must be equal or lower than 100 Hz (50
Hz per eye). In case the input frequency is higher than 100 Hz (50 Hz per eye, 59.94 & 60 Hz in practice), the
“Field dominance” setting has no effect.
Single 3D channel - Full resolution - other formats
Contains Frame packing and Line Alternating (3G-B).
To activate the single channel 3D mode select:
MENU > Input > 3D > Frame packing (FHD3 D)
or
MENU > Input > 3D > Line Alternating (3G -B) (only for SDI input)
Single 3D channel - Half resolution
3D content is distributed by one 3D source by means of “Side By Side”, “Top Bottom” or “SENSIO®Hi-Fi 3D”..
To activate this single channel 3D mode select one of the three op
MENU > Input > 3D > Side-By-Side (Half)
MENU > Input > 3D > Top-and-Bottom (Half)
®
MENU > Input > 3D > SENSIO
Example: A 3D HDMI source with a Side by Side video of 60 Hz results in a 60 Hz video per eye.
In this mode the 3D Input Module also generates the 3D sync.
Possible sources: Display Port, HDMI, DVI , SDI input.
3D Decoder - FFC (only on 3D input)
tions:
Dual 3D channel - Two parallel 3D content streams
3D content is applied to the projector via two input ports. One port is used for content of the left eye, the other port for the right eye.
Example: Two parallel DVI streams of 60 Hz: DVI cable 1 is connected with the DVI port of the projector. DVI cable 2 is connected
via a HDMI converter cable with the HDMI port of the 3D Input Module. To switch the HDMI/DP input to HDMI, select
MENU > Input > Advanced Settings > HDM I/DP > HDMI.
For the second source the correct type has to be selected as follows with the first source already selected :
MENU > Input > 3D > Second Input > “select corresponding slot number”
The 3D Input Module is activated for Dual 3D channel:
MENU > Input > 3D > Frame Sequential – Dual c hannel
Possible sources: 2 x DVI , 2 x SDI. If two 3D Input Modules are installed: 2 x HDMI or 2 x DisplayPort.
R5905032 HDX SERIES 23/01/2018
95
Page 100
9. Input
SENSIO®Hi-Fi 3D
(2)
1
3
2
(1)
1
3
2
4
2
4
1
3
1
3
2
4
2
4
1
3
1
1
1
4
3
2
4
4
2
3
4
2
3
(4)
(5)
(6)
1234
1234
1234
1234
1234
1234
1234
1234
(7)(3)
Image 9-58
®
HI-FI 3D decoding
SENSIO
1SENSIO®Hi-Fi 3D stream
2 Left expansion
3 Right expansion
4
SENSIO
5
SENSIO
6 Right stream
7
Left stream
SENSIO
enables an automatic detection of 2D, Top-and-Bottom, Side-by-Side and the SENSIO
fast detection time between these formats. Only progressive formats are supported. Interlaced formats will be displayed in 2D (one
eye only). The SENSIO
The acronym FFC stands for ‘Full Frame Compatible’, in other words, the decoder handles all full frame based 3D formats.
®
Hi-Fi 3D interpolation
®
Hi-Fi 3D interpolation
®
3D Decoder - FFC is using both the SENSIO®3D Decoder as well as the SENSIO®Autodetect functionality. This mode
®
Autodetect feature requires a minimum of 1120x540 active pixels per field/frame to operate.
®
Hi-Fi 3D format, with a clean transition and
Double or triple flash
Double or triple flash is used for 3D sources to avoid flickering images.
Input frequency < 40Hz/eye → triple flash will be used and results in:
• 144Hz for 24Hz/eye input
• 150Hz for 25Hz/eye input
• 180Hz for 30Hz/eye input
Input frequency between 40Hz and 51Hz/eye → double flash will be used and results in:
• 192Hz for 48Hz/eye input
• 200Hz for 50Hz/eye input
Supported formats
5–cable analog DVI analog
Max. resolution:
1920x1200@60Hz or
2048x1080@60Hz.
1400x1050@120Hz or
1600x900@120Hz.
HD formats only.
Max. resolution:
1920x1080@30Hz or
1280x720@60Hz.
Max. resolution:
1920x1200@60Hz or
2048x1080@60Hz.
1280x720@120Hz or
1280x800@120Hz.
HD formats only.
Max. resolution:
1920x1080@30Hz or
1280x720@60Hz.
Frame sequential
Single channel
Frame Packing
(FHD3D)
DVI/HDMI/DP
Fpix ≤ 210 MHz Fpix ≤ 210 MHz Fpix ≤ 170 MHz Fpix ≤150 MHz
Max. resolution:
1920x1200@60Hz or
2048x1080@60Hz.
1400x1050@120Hz or
1600x900@120Hz.
Interlaced/progressive Interlaced/progressive Interlaced/progressive Interlaced/progressive
HD formats only.
Max. resolution:
1920x1080@30Hz or
1280x720@60Hz.
Progressive only Progressive only Progressive only Progressive only
SDI
Max. resolution:
1920x1200@60Hz,
2048x1080@60Hz or
1280x720@120Hz.
HD formats only.
Max. resolution:
1920x1080@30Hz or
1280x720@60Hz.
96 R5905032 HDX SERIES 23/01/2018
Loading...