Barco HDX W12, HDX W20, HDX, HDX W14 User Manual

Page 1
HDX series
User and Installation manual
For HDX, HDX W12, HDX W 14,HDX W1 8 and HDX W20
R5905032/14 02/03/2015
Page 2
Product revision
Software version: 1.9.
Barco nv Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.883.86 Support: www.barco.com/esupport Visit us at the web: www.barco.com
Printed in Belgium
Page 3
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war­ranties or merchantability and tness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site w
h
ttps://www.barco.com/en/signin.
ww.barco.com or from the secured Barco web site
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.
EN55022/CISPR22 Class A ITE (Information Technology Equipment)
Class A ITE is a category of all other ITE which satises the class A ITE limits but not the class B ITE limits. Such equipment should not be restricted in its sale but the following warning shall be included in the instructions for use:
Warning : This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pur These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio co cause harmful interference, in which case the user will be responsible for correcting any interference at his own expense
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
mmunications. Operation of this equipment in a residential area may
suant to Part 15 of the FCC rules.
GNU-GPL code
If you would like a copy of the GPL source code contained in this product shipped to you on CD, please contact Barco. The cost of preparing and mailing a CD will be charged.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justied notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate pe reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component of the system or independent service, will guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modications or repairs on goods delivered by Barco, or if the goods are handled incorrectly, in particular if the systems are operated incorrectly or if, after the transfer of risks, the goods are subject to inuences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specied in this manual must be complied with by the customer.
riod. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
be deemed invalid provided the damage is not proven to be attributed to the absence of properties
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufacturers.
Page 4
Page 5
Table of contents
TABLE OF CONTENTS
1. Safety................................................................................................................. 7
1.1 General considerations............................................................................................................... 7
1.2 Important safety instructions ......................................................................................................... 8
1.3 Light beam Hazard Distance (HD) ..................................................................................................10
1.4 HD infunction of the lensThrow Ratio(TR)........................................................................................ 11
1.5 Important warnings concerning HDX ight cases ..................................................................................12
2. General..............................................................................................................13
2.1 Installation requirements .. . .........................................................................................................13
2.2 Unpacking the projector .............................................................................................................14
2.3 Initial inspection......................................................................................................................15
2.4 HDX ight case ......................................................................................................................16
2.5 Projector congurations .............................................................................................................16
2.6 Projector air inlets and outlets.......................................................................................................20
2.7 Free downloadof Projector Toolset.................................................................................................20
2.8 Installationprocessoverview........................................................................................................21
3. Physical installation ..............................................................................................23
3.1 Remote control unit (RCU) . .........................................................................................................23
3.1.1 RCU battery installation.......................................................................................................23
3.1.2 RCU rugged case installation ................................................................................................24
3.1.3 RCU XLR adaptor installation ................................................................................................25
3.1.4 Using the XLR adaptor of the RCU. . . ........................................................................................25
3.1.5 RCU usage possibilities ......................................................................................................26
3.2 Lenses ...............................................................................................................................27
3.2.1 Available lenses...............................................................................................................27
3.2.2 Lens selection .................................................................................................................28
3.2.3 Lens installation ...............................................................................................................29
3.2.4 Lens removal . .................................................................................................................30
3.2.5 Lens safety cable .............................................................................................................31
3.2.6 Lens shift, zoom & focus......................................................................................................33
3.2.7 Scheimpugadjustment ......................................................................................................34
3.3 Connecting the projector with the power net .......................................................................................38
3.4 Alignment of a table mounted projector. . . . . ........................................................................................39
3.5 Mounting the bottom carry handler .................................................................................................39
3.6 Mounting the top carry handler......................................................................................................41
3.7 Suspension of the projector with rigging clamps ...................................................................................42
3.8 Alignment of a ceiling mounted projector . . . ........................................................................................44
4. Input & Communication..........................................................................................47
4.1 Introduction ..........................................................................................................................47
4.2 Input source connections. . . .........................................................................................................48
4.3 Communication connections ........................................................................................................50
4.4 Utility-Accessory Outlet..............................................................................................................53
5. Getting started .....................................................................................................55
5.1 RCU & Local keypad................................................................................................................55
5.2 Terminology overview ...............................................................................................................55
5.3 Poweron projector ..................................................................................................................57
5.4 Switching to standby ................................................................................................................60
5.5 Poweroff projector ..................................................................................................................60
5.6 Status LEDs .........................................................................................................................61
5.7 Using the RCU.......................................................................................................................61
5.8 Projector Address....................................................................................................................63
5.8.1 Displaying and Programming addresses into the RCU . . ....................................................................63
5.8.2 Controlling the projector ......................................................................................................63
5.9 Source selection.....................................................................................................................63
6. Quick set up adjustment.........................................................................................65
6.1 Text boxes ONor OFF ..............................................................................................................65
6.2 Quick Lens Adjustment via LENS key ..............................................................................................65
6.3 Direct Lens Adjustment (RCU)......................................................................................................67
6.4 Quickpicture inpicture..............................................................................................................68
6.5 Quick language selection ...........................................................................................................68
7. Start up of the adjustment mode ...............................................................................71
7.1 About the adjustment mode .........................................................................................................71
7.2 Aboutthe use ofthe remotecontrolandthelocal keypad.........................................................................71
7.3 Start up the adjustment mode.......................................................................................................71
7.4 Navigation and adjustments.........................................................................................................72
7.5 Menu memory .......................................................................................................................73
7.6 Shortcut keys to the menus .........................................................................................................73
7.7 Test patterns in adjustment mode. ..................................................................................................74
R5905032 HDX SERIES 02/03/2015
1
Page 6
Table of contents
7.8 Help informationin adjustment mode...............................................................................................74
8. Input .................................................................................................................75
8.1 Input menu overview ................................................................................................................75
8.2 Input Selection.......................................................................................................................76
8.3 Advanced Settings...................................................................................................................77
8.3.1 About Input Setup .............................................................................................................77
8.3.2 Input conguration ............................................................................................................77
8.3.3 DVI - RGB input...............................................................................................................78
8.3.4 SDI input ......................................................................................................................79
8.3.5 5 cable input. . .................................................................................................................80
8.3.6 HDMI - DisplayPort input (3D input module) .................................................................................80
8.4 Input locking . ........................................................................................................................81
8.5 Minimum delay.......................................................................................................................82
8.6 Native resolution.....................................................................................................................83
8.7 No Signal ............................................................................................................................84
8.7.1 Backgroundcolor .............................................................................................................84
8.7.2 Background Logo .............................................................................................................85
8.7.3 Shutdown settings ............................................................................................................86
8.7.4 Shutdown retarding time......................................................................................................86
8.7.5 Auto Dimming.................................................................................................................87
8.8 EDID .................................................................................................................................88
8.8.1 Congure an input .. . .........................................................................................................88
8.8.2 Create custom EDID le......................................................................................................90
8.8.3 Delete a custom EDID le ....................................................................................................91
8.8.4 Delete all custom EDID le...................................................................................................92
8.9 3D input ..............................................................................................................................93
8.9.1 About 3D modes ..............................................................................................................93
8.9.2 Activate 3D....................................................................................................................96
8.9.3 Auto detection.................................................................................................................97
8.9.4 Input type selection ...........................................................................................................98
8.9.5 3D second input...............................................................................................................99
8.9.6 L-R Synchronisation, eld dominance.......................................................................................100
8.9.7 L-R Synchronisation,Invert 3D sync out....................................................................................101
9. Image .............................................................................................................. 105
9.1 Image menu overview ..............................................................................................................105
9.2 Start up the Image adjustments. . . .................................................................................................106
9.3 Image settings ......................................................................................................................106
9.3.1 Contrast ......................................................................................................................106
9.3.2 Brightness....................................................................................................................107
9.3.3 Saturation ....................................................................................................................108
9.3.4 Phase.........................................................................................................................109
9.3.5 Color temperature (xed values)............................................................................................111
9.3.6 Color temperature (custom values) .........................................................................................112
9.3.7 Input Balance ................................................................................................................113
9.3.7.1 Introduction to Input Balance . . .......................................................................................113
9.3.7.2 Adjusting the input balance ...........................................................................................114
9.3.8 Image settings, defaults .....................................................................................................117
9.4 Aspect Ratio........................................................................................................................118
9.5 Timings..............................................................................................................................120
9.5.1 Source timings ...............................................................................................................120
9.5.2 Advanced timings,clamp delay - clamp width ..............................................................................121
9.6 Image File Services ................................................................................................................123
9.6.1 Files and le manipulations..................................................................................................123
9.6.2 Manual Load le .............................................................................................................123
9.6.3 File Load Filter ...............................................................................................................124
9.6.4 Delete a le ..................................................................................................................125
9.6.5 Delete all custom les .......................................................................................................126
9.6.6 Rename custom les ........................................................................................................127
9.6.7 Copy custom le.............................................................................................................128
9.6.8 Image le service options, Load le.........................................................................................130
9.6.9 Image le service options, Auto Picture Alignment .........................................................................130
9.7 Save custom settings...............................................................................................................131
9.8 Splash image .......................................................................................................................132
10. Layout............................................................................................................. 135
10.1 Layout menu overview .............................................................................................................135
10.2 Introduction .........................................................................................................................135
10.3 Main window . .......................................................................................................................136
10.3.1 Main window source selection...............................................................................................136
10.3.2 Main window size ............................................................................................................136
10.3.3 Main window position ........................................................................................................138
10.4 PiP window . . .......................................................................................................................139
10.4.1 Introduction to PIP .. . ........................................................................................................140
10.4.2 Picture inPicture activation..................................................................................................140
2
R5905032 HDX SERIES 02/03/2015
Page 7
Table of contents
10.4.3 PiP window, source selection................................................................................................141
10.4.4 PiP window, Size ............................................................................................................142
10.4.5 PiP window, position . ........................................................................................................143
10.5 Layout File Services................................................................................................................145
10.5.1 Load layout le...............................................................................................................145
10.5.2 Rename layout le ...........................................................................................................146
10.5.3 Delete layout le .............................................................................................................147
10.5.4 Delete all layout les.........................................................................................................148
10.5.5 Copy or Save as layout le ..................................................................................................149
10.6 Lens behavior.......................................................................................................................150
11. Lamp............................................................................................................... 153
11.1 Lampmenuoverview...............................................................................................................153
11.2 Lamppower mode..................................................................................................................153
11.3 Lamppower.........................................................................................................................154
11.4 Auto dimming when onPause .....................................................................................................155
11.5 Auto dimming when No Signal .....................................................................................................156
11.6 Auto dimming when Over-temperature ............................................................................................157
11.7 CLO mode (Constant light output mode) . . . .......................................................................................158
11.8 CLO targets.........................................................................................................................160
11.9 LPS power ..........................................................................................................................160
11.10 Lamp identication..................................................................................................................161
11.11 Z-axis adjustment...................................................................................................................162
12. Alignment......................................................................................................... 163
12.1 Alignment menu overview..........................................................................................................163
12.2 Orientation ..........................................................................................................................164
12.3 Lens adjustment, zoom - focus ....................................................................................................165
12.4 Lens adjustment, shift ..............................................................................................................166
12.5 Lens adjustment, mid position .....................................................................................................167
12.6 Calbrate lensat startup.............................................................................................................168
12.7 Calibrate lens.......................................................................................................................169
12.8 Warping.............................................................................................................................170
12.8.1 About warping................................................................................................................170
12.8.2 Warp activation - deactivation ...............................................................................................171
12.8.3 Start up manualadjustment .................................................................................................171
12.8.4 Warp adjustment principle...................................................................................................173
12.8.5 Setting the warping level..................................................................................................... 175
12.8.6 Warp adaptation steps.......................................................................................................175
12.8.7 Making selections and adjustments . . .......................................................................................176
12.8.8 Keystone correction workow ...............................................................................................177
12.8.9 Linearity adjustment, workow ..............................................................................................178
12.8.10 Selecting and changing the position of a specic point.....................................................................179
12.8.11 Scaling the image............................................................................................................179
12.8.12 Shifting the image............................................................................................................180
12.8.13 Rotating the image. . . ........................................................................................................180
12.8.14 Hardware Reset..............................................................................................................182
12.8.15 OSD opacity. .................................................................................................................182
12.8.16 Warp le service, load le ...................................................................................................184
12.8.17 Warp le service, save to le................................................................................................185
12.8.18 Warp le service,save as ...................................................................................................185
12.8.19 Warp le service, rename le................................................................................................186
12.8.20 Warp le service, delete le .................................................................................................187
12.8.21 Warp le service, delete all les.............................................................................................188
12.8.22 Warp board reset.............................................................................................................189
12.8.23 Warp board and values reset................................................................................................190
12.8.24 Alternative SideKeystone ................................................................................................... 191
12.9 Blanking adjustment................................................................................................................192
12.10 Contrast-Intensity...................................................................................................................194
12.11 Gamma .............................................................................................................................195
12.12 Internal patterns ....................................................................................................................195
12.13 Color space.........................................................................................................................197
12.14 Scenergix ...........................................................................................................................199
12.14.1 Introduction. . . ................................................................................................................199
12.14.2 Preparations. . ................................................................................................................200
12.14.3 Scenergix activation .........................................................................................................200
12.14.4 Scenergix pattern ............................................................................................................200
12.14.5 Scenergix adjustment lines ..................................................................................................201
12.14.6 Data doubling ................................................................................................................202
12.14.7 White level adjustment (blending area) . . . ..................................................................................204
12.14.8 Black level adjustment.......................................................................................................207
12.14.9 Scenergix Reset .............................................................................................................210
12.15 3DGlasses .........................................................................................................................211
12.15.1 Dark timeadjustment ........................................................................................................211
12.15.2 Left-right output reference delay ............................................................................................ 214
12.15.3 3D Sync Loop Through ......................................................................................................215
R5905032 HDX SERIES 02/03/2015
3
Page 8
Table of contents
12.16 High End Systems Mirror...........................................................................................................216
13. Projector Control................................................................................................ 219
13.1 Projector Control menu overview . .................................................................................................219
13.2 Individual Projector Address .......................................................................................................220
13.3 Projector CommonAddress........................................................................................................221
13.4 Serial Communication ..............................................................................................................222
13.4.1 Baud ratesetup .............................................................................................................. 222
13.4.2 Interface Standard ...........................................................................................................222
13.5 Network.............................................................................................................................223
13.5.1 Introduction to a Network connection .......................................................................................223
13.5.2 Wired DHCP set up..........................................................................................................224
13.5.3 Wired IP address set up .....................................................................................................225
13.5.4 Wired subnet mask set up . . .................................................................................................226
13.5.5 Wired default gateway set up................................................................................................228
13.5.6 Wireless network activation.................................................................................................. 229
13.5.7 Wireless access points selection and setup ................................................................................230
13.5.8 Wireless DHCP set up .......................................................................................................232
13.5.9 Wireless xed IP address set up ............................................................................................233
13.5.10 Wireless subnet mask set up ................................................................................................234
13.5.11 Wireless default gateway set up.............................................................................................236
13.6 IRControlswitching ................................................................................................................237
13.7 DMX.................................................................................................................................238
13.7.1 DMX address. ................................................................................................................238
13.7.2 DMX universe................................................................................................................ 240
13.7.3 DMX mode . . . ................................................................................................................241
13.7.4 Art-Net DMX..................................................................................................................242
13.7.5 Front XLR output voltage control............................................................................................243
13.7.6 Monitor .......................................................................................................................245
13.7.7 DMX Shutdown ..............................................................................................................246
13.7.8 DMX Shutdownretarding time...............................................................................................247
13.8 Buttons..............................................................................................................................248
13.8.1 Standby button ...............................................................................................................248
13.8.2 Shortcut keys.................................................................................................................249
13.9 Menuposition.......................................................................................................................250
13.10 Local LCD...........................................................................................................................250
13.11 Language selection. ................................................................................................................251
13.12 Scheduler ...........................................................................................................................252
13.12.1 Add a task tothelist ......................................................................................................... 253
13.12.2 Edita task....................................................................................................................256
13.12.3 Delete task ...................................................................................................................257
13.12.4 Scheduler, on or off . . ........................................................................................................258
13.13 GSM Conguration,activation.....................................................................................................259
13.14 GSM Conguration,subscription ..................................................................................................261
13.15 FLEX, light output conguration....................................................................................................263
13.15.1 About FLEX, Lightoutput control............................................................................................263
13.15.2 Light output conguration via OSD menu . ..................................................................................264
13.15.3 Congure projector’s light output via SMS..................................................................................265
13.16 SMS services.......................................................................................................................265
13.16.1 Request for noti
13.16.2 Request for information ......................................................................................................266
13.16.3 Lamp ignition admission..................................................................................................... 266
cations.....................................................................................................265
14. Service ............................................................................................................ 267
14.1 Service menu overview.............................................................................................................267
14.2 Identication ........................................................................................................................268
14.3 Diagnosis ...........................................................................................................................269
14.3.1 Versions......................................................................................................................269
14.3.2 Measurements............................................................................................................... 270
14.3.3 Logging.......................................................................................................................272
14.3.4 Board Id ......................................................................................................................274
14.3.5 Notication ...................................................................................................................275
14.3.6 Tiltsensor ....................................................................................................................276
14.4 Internal Service Patterns...........................................................................................................277
14.5 Convergence .......................................................................................................................281
14.6 Factorydefaults.....................................................................................................................282
14.7 USB memory .......................................................................................................................283
14.8 Reset Formatter ....................................................................................................................285
14.9 Rell mode . . . .......................................................................................................................285
14.10 Save Custom Settings..............................................................................................................286
14.11 Special HD Camera mode . ........................................................................................................287
14.12 Auto Dimming when over-temperature ............................................................................................288
14.13 TimeandDate......................................................................................................................289
15. Maintenance...................................................................................................... 291
15.1 Cleaning the lens . . . ................................................................................................................291
4
R5905032 HDX SERIES 02/03/2015
Page 9
Table of contents
15.2 Cleaning the exterior of the projector ..............................................................................................291
16. Servicing.......................................................................................................... 293
16.1 Inserting an input module .. ........................................................................................................293
16.2 Removal of the lamp house ........................................................................................................294
16.3 Installation of the lamp house ......................................................................................................295
16.4 Removal of the front cover .........................................................................................................296
16.5 Mounting the front cover . . . ........................................................................................................298
16.6 Removal of the lamp cover.........................................................................................................299
16.7 Mounting the lamp cover . . .........................................................................................................300
16.8 Replacement of the high density dust lter........................................................................................301
16.9 Remove and clear metal front lter ................................................................................................302
A. Dimensions ........................................................................................................ 305
A.1 Dimensions ofa HDX projector....................................................................................................305
B. Specications ..................................................................................................... 307
B.1 Specications of the HDX W12 ....................................................................................................307
B.2 Specications of the HDX W14 ....................................................................................................308
B.3 Specications of the HDX W18 ....................................................................................................309
B.4 Specications of the HDX W20 FLEX .............................................................................................310
B.5 Technical Regulations ..............................................................................................................312
C. Standard source les............................................................................................ 313
C.1 Table overview......................................................................................................................313
D. DMX chart.......................................................................................................... 317
D.1 DMX chart, Basic ...................................................................................................................317
D.2 DMX chart, Full.....................................................................................................................317
D.3 DMX chart, Extended ...............................................................................................................318
E. Stacking HDX projectors ........................................................................................ 321
E.1 Mount stacking points ..............................................................................................................321
E.2 Stacking HDX projectors ...........................................................................................................321
E.3 AligningstackedHDXprojectors...................................................................................................324
F. Environmental information ...................................................................................... 327
F.1 Disposalinformation................................................................................................................327
F.2 Rohs compliance...................................................................................................................327
F.3 Production address . ................................................................................................................329
F.4 Importers contact information ......................................................................................................329
Index.................................................................................................................... 331
R5905032 HDX SERIES 02/03/2015 5
Page 10
Table of contents
6 R5905032 HDX SERIES 02/03/2015
Page 11
1. SAFETY
About this chapter
Read this chapter attentively. It contains important information to prevent personal injury while installing and using a HDX projector. Furthermore, it includes several cautions to prevent damage to the HDX projector. Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing your HDX projector. After this chapter, addi­tional “warnings” and “cautions” are given depending on the installation procedure. Read and follow these “warnings” and “cautions” as well.
1.1 General considerations
WARNING: Ensure you understand and follow all the safety guidelines, safety instructions, warnings and
cautions mentioned in this manual.
WARNING: Be aware of suspended loads.
1. Safety
WARNING: Wear a hard hat to reduce the risk of personal injury.
WARNING: Be careful while working with heavy loads.
WARNING: Mind your ngers while working with heavy loads.
CAUTION: High pressure lamp may explode if improperly handled.
General safety instructions
Before operating this equipment please read this manual thoroughly and retain it for future reference.
Installation and preliminary adjustments should be performed by qualified Barco personnel or by authorized Barco service deal- ers.
All warnings on the projector and in the documen
All instructions for operating and use of this equipment must be followed precisely.
All local installation codes should be adhered to.
tation manuals should be adhered to.
Notice on safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, EN60950-1, UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology equipment including electrical business equipment. These safety standards impose important requirements on the use of safety critical components, materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of re. Simulated single fault condition testing ensures the safety of the equipment to the user even when the equipment’s normal operation fails.
Users denition
Throughout this manual, the term S necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE ELEC­TRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize
R5905032 HDX SERIES 02/03/2015 7
ERVICE PERSONNEL refers to persons having appropriate technical training and experience
Page 12
1. Safety
the potential risk to themselves or other persons. The term USER and OPERATOR refers to any person other than SERVICE PER­SONNEL, AUTHORIZED to operate professional projection systems.
A HDX projector is intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with potential hazards associated with high voltage, high intensity light beams, ultraviolet exposure and high temperatures generated by the lamp and associated circuits. Only qualied SERVICE PERSONNEL, knowledgeable of such risks, are allowed to perform service functions inside the product enclosure.
1.2 Important safety instructions
To prevent the risk of electrical shock
This product should be operated from a mono phase AC power source.
This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power cables are the correct one, consult your dealer. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself.
Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer.
Do not operate the projector with a damaged cord. Replace the cord. Do not operate the projector if the projector has been dropped or damaged - until it has been examined and approved for operation by a qualied service technician.
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
If an extension cord is necessary, a cord with a current rating at least equ for less amperage than the projector may overheat.
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of re or electrical shock.
Do not expose this projector to rain or moisture.
Do not immerse or expose this projector in water or other liquids.
Do not spill liquid of any kind on this projector.
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualied service personnel before resuming operations.
Do not disassemble this projector, always take it to an authorized trained service person when service or repair work is required.
Do not use an accessory attachment which is not recommended by the manufacturer.
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will preven
t damage to the device due to lightning and AC power-line surges.
al to that of the projector should be used. A cord rated
To prevent personal injury
Isolate electrically before replacing the lamp or lamp house. Caution: Hot lamp (house).
Caution: High pressure lamp may explode if improperly handled. Refer servicing to qualied service personnel.
To prevent injury and physical damage, always read this manual and all labels on the system before inserting the lamp casing, connecting to the wall outlet or adjusting the projector.
To prevent injury, take note of the weight of the projector. Minimum 4 persons are needed to carry the projector.
To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.
Warning: extremely high brightness lamps: This projector uses extr directly into the lens or at the lamp. If the projection distance is less than 6 meter, any person needs to be at least 4 meters away from the projected image. Avoid close range reection of the projected image on any reecting surface (such as glass, metal, …) . When operating the projector, we strongly
Before attempting to remove any of the projector’s covers, you must turn off the projector and disconnect from the wall outlet.
When required to switch off the projector, to access parts inside, always disconnect the power cord from the power net.
The power input at the projector side is considered as the disconnect device. When required to switch off the projector, to access parts inside, always disconnect the power cord at the projector side. In case the power input at the projector side is not accessible (e.g. ceiling mount), the socket outlet supplying the projector shall be installed nearby the projector and be easily accessible, or a readily accessible general disconnect device shall be incorporated in the xed wiring.
Never stack more than two (2) HDX projectors in a hanging conguration (truss) and never stack more than three (3) HDX projectors in a base stand conguration (table mount).
When using the projector in a hanging conguration, always mount 2 safety cables. See installation manual for the correct use of these cables.
Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and possible injury to the user.
8
recommend wearing suitable safety glasses.
emely high brightness lamps. Never attempt to look
R5905032 HDX SERIES 02/03/2015
Page 13
1. Safety
It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches.
Warning: Protection from ultraviolet radiation: Do not look directly in the light beam. The lamp contained in this product is an intense source of light and heat. One component of the light emitted from this lamp is ultraviolet light. Potential eye and skin hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unnecessary exposure. Protect yourself and your employees by making them aware of the hazards and how to protect themselves. Protecting the skin can be accomplished by wearing tightly woven garments and gloves. Protecting the eyes from UV can be accomplished by wearing safety glasses that are designed to provide UV protection. In addition to the UV, the visible light from the lamp is intense and should also be considered when choosing protective eye wear.
Exposure to UV radiation: Some medications are known to make individuals extra sensitive to UV radiation. The American Conference of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure for an-8 hour day to be less than 0,1 micro-watts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to assure employees are not exposed to cumulative radiation levels exceeding these government guidelines. The exposer of this UV radiation is allowed for only 1 hour per day for maintenance and service persons.
Cooling liquid circuit. The projector contains a cooling circuit lled with Blue antifre
eze diluted (1/3 ethanediol – 2/3 Demi water). When the cooling circuit leaks, switch off the device and contact a service technician. The liquid is not for household use. Keep out of reach of children. Harmful by oral intake. A
void exposure to pregnant women.
Avoid contact with eyes, skin and clothing. Avoid inhale of the noxious fumes.
When the projector is mounted above persons, mount always a lens safety cable.
To prevent re hazard
Do not place ammable or combustible materials near the projector!
Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This projector radiates heat on its external surfaces and from ventila safe. Exposing ammable or combustible materials into close proximity of this projector could result in the spontaneous ignition of that material, resulting in a re. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of the projector whereby no ammable or combustibl 40 cm (16”) for all DLP projectors. The exclusion zone on the lens side must be at least 5 m. Do not cover the projector or the lens with any material while the projector is in operation. Keep ammable and combustible materials away from the projector at all times. Mount the projector in a well ventilated area
away from sources of ignition and out of direct sun light. Never expose the projector to rain or moisture. In the event of re, use sand, CO electrical re. Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco repl
acement parts as they may degrade the safety of this projector.
Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
Projection rooms must be well ventilated or cooled in order to avoid build up of heat.
Let the projector cool down completely before storing. Remove cord from the projector when storing.
Heat sensitive materials should not be placed in the path of the exhausted air or on the lamp house.
tion ducts during normal operation, which is both normal and
e materials are present. The exclusion zone must be not less than
or dry powder re extinguishers. Never use water on an
2
To prevent projector damage
This projector has been designed for use with a specic lamp (house) type. See installation instructions for its correct type.
The air lters of the projector must be cleaned or replaced on regular base (a "clean" booth would be monthly-minimum). Neglecting this could result in disrupting the air ow inside the projector, causing overheating. Overheating may lead to the projector shutting down during operation.
The projector must always be installed in a manner which ensures free ow of air into its air inlets and unimpeded evacuation of the hot air from its cooling system.
In order to ensure that correct airow is maintained, and that the projector complies with Electromagnetic Compatibility (EMC) requirements, it should always be operated with all of it’s covers in place.
Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The device should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the mains supply immediately. Do not operate the projector again until it has been checked by qualied service personnel.
Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects may not be nearer to the projector than 1
Do not use this equipment near water.
Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as high power laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices which case there is a loss of warranty.
Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror Devices case there is a loss of warranty.
Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory.
0 cm (4") on any side.
TM
in which
TM
in
R5905032 HDX SERIES 02/03/2015
9
Page 14
1. Safety
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution.
To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.
Rated maximum ambient temperature, t
The lamp house shall be replaced if it has become damaged or thermally deformed.
= 40 °C (104 °F).
a
On servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials and risk of electric shock.
Refer all servicing to qualied service personnel.
Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can lead to permanent damage to the projector and cancellation of the warranty.
Unplug this product from the wall outlet and refer servicing to qualied service technicians under the following conditions:
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualied technician to restore the product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.
Replacement parts: When replacement parts are required, be sure the service technici parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitu­tions may result in degraded performance and reliability, re, electric shock or other hazards. Unauthorized substitutions may void warranty.
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
Possible explosion hazard: Always keep in mind the caution below:
an has used original Barco replacement
CAUTION: Xenon compact arc lamps are highly pressurized. When ignited, the normal
of the bulb increases the pressure to a level at which the bulb may explode if not handled in strict accordance to the manufacturer’s instructions. The bulb is stable at room temperature, but may still explode if dropped or otherwise mishandled. Whenever the lamp house, containing a xenon lamp, has t the protective container or cloth has to be removed from the xenon lamp, authorized protective clothing MUST be worn!
operating temperature
o be dismantled or whenever
To prevent battery explosion
Danger of explosion if battery is incorrectly installed.
Replace only with the same or equivalent type recommended by the manufacturer.
For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and regulations to ensure proper disposal.
1.3 Light beam Hazard Distance (HD)
HD
Light beam Hazard Distance (HD) is the distance from the source at which the intensity or the energy per surface unit becomes lower than the applicable safety limit. is closer from the source than the HD.
Restriction Zone (RZ) based on the HD
The HD is dened from the projection lens surface towards the position of the lowest projected beam where the irradiance equals the applicable safety limit. The HD depends on the amount of lumens produced by the projector and the type of lens installed. See next chapter HD in function of the lens Throw R
To protect untrained users the installation shall comply with the following installation requirements: light output levels in excess of the limits shall not be permitted at any point less than 2.0 meters (SH image 1-1) above any surface upon which persons are assumed to stand or 1 meter (SW image 1-1) below or in lateral separation from any place where such persons are assumed to be. See image 1-1.
atio (TR).
The light beam can thus be considered as dangerous if the operator
10
R5905032 HDX SERIES 02/03/2015
Page 15
1. Safety
RA TH
HD
RA
SH
RZ
SH
Image 1-1 ASideview. B Top view. RA Restricted Access location (boot area of projector). PR Projector. TH Theater. RZ Restriction Zone in the theater. SH Separation Height. Must be minimum 2 meter. SW Separation Width. Must be minimum 1 meter.
Based on national requirements, no person is allowed to enter the projected beam within the zone between the projection lens and the related hazard distance (HD). This shall be ph The minimum separation height takes into account the surface upon which persons are assumed to stand.
On image 1-1 a typical setup is displayed. It must be veried by the installer if these minimum requirements are met. If required a restricted zone (RZ) in the theater must be established. This can be done by using physical barrier, like a red rope as illustrated in image 1-2.
ysically impossible by creating sufcient separation height or by placing barriers.
PR
(B) TOP VIEW(A) SIDE VIEW
TH
HD
SW
SW
SW
RZ
1m
SW
PR
Image 1-2
1.4 HD in function of the lens Throw Ratio (TR)
TR (Throw Ratio)
The ratio of the distance to the screen (throw) to the screen width.
R5905032 HDX SERIES 02/03/2015 11
Page 16
1. Safety
HDX projector Hazard Distance
8
7
6
5
4
HD [m]
3
2
1
0
0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0 7,5 8,0 8,5 9,0 10,0
Image 1-3 HD (in meter) in function of the Throw Ratio (TR)
TR
1.5 Important warnings concerning HDX ight cases
Important warnings concerning stacking/transporting HDX rental ight cases
Stack maximum two (2) HDX rental ight cases high. Never higher.
Surface on which ight case is standing must be level to ensure that the total load is evenly spread out among the four wheels. The surface must also be able to support the load safely.
Before stacking or transporting ight cases, check the wheels and their xation screws for wear or defects.
Before stacking or transporting ight cases, check that the four lock handles on each ight case are in good working order and locked securely.
When stacked, make sure the wheels of the upper ight case are precisely positioned in the stacking dishes of the ight case below.
•Stackedflight cases may not be moved. Before stacking, the lower flight case must already be in its final resting position before placing the second upon it.
Never stack loaded ight cases in a truck or other transport medium, unless each ight case is rigidly strapped tight.
In the event of a wheel breaking, ight cases must be rigidly strapped tight to prevent a stack collapsing.
Use an appropriate forklift to raise ight cases and take the necessary precautions to avoid personnel injury.
12
R5905032 HDX SERIES 02/03/2015
Page 17
2. GENERAL
About this chapter
Read this chapter before installing your HDX projector. It contains important information concerning installation requirements for the HDX projector, such as minimum and maximum allowed ambient temperature, humidity conditions, required safety area around the installed projector, required power net, etc.
Furthermore, careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system.
Overview
Installation requirements
Unpacking the projector
Initial inspection
HDX ight case
Projector congurations
Projector air inlets and outlets
Free download of Projector Toolset
Installation process overview
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guar­antee. Observing the specication mentioned in this chapter is critical for projector performance. Neglecting this can result in loss of warranty.
2. General
2.1 Installation requirements
Environment conditions
Table below summarizes the physical environment in which the HDX projector m
Environment
Ambient Temperature
Humidity
Altitude
Let the projector acclimatize after unpacking. Neglecting this may result in a startup failure of the Light Pro­cessor Unit.
Operating Non-Operating
10 °C (50 °F) to 40 °C (104 °F) -15°C (5°F) to 60°C (140°F)
5% to 85% RH Non-condensed 5% to 95% RH Non-Condensed
-60 (-197Ft) to 3000m (9843Ft) -60 (-197Ft) to 10000m (32810Ft)
Cooling requirements
The projector is fan cooled and must be installed with sufcient space around the projector head, minimum 10 cm (4 inch) to ensure sufcient air ow. It should be used in an area where the ambient temperature, as measured at the projector air inlet , does not exceed +40°C (+104°F).
Clean air environment
A projector must always be mounted in a manner which ensures the free ow of clean air into the projectors ventilation inlets. For installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines or similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading performance), then it is highly advisable and desirable to have this contamination removed prior to it reaching the projectors clean air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not a feasible solution then measures to relocate the projector to a clean air environment should be considered.
Only ever use the manufacturer’s recomme use industrial strength cleaners on the projector’s optics as these will degrade optical coatings and damage sensitive optoelectronics components. Failure to take suitable precautions to protect the projector from the effects of persistent and prolonged air contam­inants will culminate in extensive an be noneffective and impracticable. Damage of this nature is under no circumstances covered under the manufacturer’s warranty and may deem the warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any repair. It is the clients responsi
bility to ensure at all times that the projector is protected from the harmful effects of hostile airborne
nded cleaning kit which has been specically designed for cleaning optical parts, never
d irreversible ingrained optical damage. At this stage cleaning of the internal optical units will
ay be safely operated or stored.
R5905032 HDX SERIES 02/03/2015
13
Page 18
2. General
particles in the environment of the projector. The manufacturer reserves the right to refuse repair if a projector has been subject to knowingly neglect, abandon or improper use.
Main Power requirements
The HDX projector operates from a nominal mono phase power net with a separate earth ground PE.
Power requirements : 110-130V/200-240 V, 15A, 50-60Hz
The power cord required to connect the projector with the power net is delivered with the projector.
Projector weight
Do not underestimate the weight of the HDX projector. The projector weights about ±50 kg (±111 lb.) without lens. Be sure that the pedestal on which the projector has to be installed is capable of handling ve (5) times the complete load of the system.
2.2 Unpacking the projector
What has to be done ?
Upon delivery, the projector is packed in a carton box upon a wooden pallet and secured with banding and thermore, to provide protection during transportation, the projector is surrounded with foam. Once the projector has arrived at the installation site, it needs to be removed from the carton box and wooden pallet in a safe manner without damaging the projector.
After unpacking let the projector acclimatize to a room temperature higher then 10°C (50°F) and lower then 40°C (104°F). Neglecting this may result in a start up failure of the Light Processor Unit.
fastening clips. Fur-
Necessary tools
cutter knife
How to unpack
1. Remove the banding around the carton box, by releasing the fastening clips as illustrated, and open the box.
Image 2-1 Opening box
2. Remove the small box on top of the projector. This box contains the accessories such as manuals, remote control, etc.
14
R5905032 HDX SERIES 02/03/2015
Page 19
Image 2-2 Remove carton and foam rubber
3. Take out the foam rubber.
4. Take out the projector.
2. General
Save the original shipping carton and packing material, they will be necessary if you ever have to ship your projector. For maximum protection, repack your projector as it was originally packed at the factory.
A rubber foam inside a plastic bag is placed into the lens opening of the projector. It’s recommended to reuse this foam and plastic back each time you transport the projector. This to prevent intrusion of dust and foreign particles.
The lens is delivered in a separate box.
2.3 Initial inspection
General
Before shipment, the projector was inspected and found to be free of mechanical and electrical defects. As soon as the projector is unpacked, inspect for any damage that may have occurred in transit. Save all packing material until the inspection is completed. If damage is found, le claim with carrier immediately. The Barco Sales and Service ofce should be notied as soon as possible.
The packaging of the HDX projector is provided with a shock-watch label. If this shock-watch label was trig­gered (red colored at arrival) during transport, that indicates that the package was possibly roughly handled by the transport company. In this case, the instructions mentioned on the label, should be followed, which are: adding a note on the “bill of lading” and informing the transport company and the Barco sales and service ofce as soon as possible.
Box content
After unpacking the projector it is recommended to check if all following items where included:
Three power cords of 2.5 meter, one CEE (7), one NEMA L6-20P and one CH2–16P
This manual (installation manual).
One Safety manual
One remote control unit (RCU)
Two AA size batteries for the RCU.
R5905032 HDX SERIES 02/03/2015
15
Page 20
2. General
One xenon lamp is mounted inside the lamp house at delivery. The projector lenses are not included in the package of the projector.
Mechanical check
This check should conrm that there are no broken knobs or connectors, that the cabinet and panel surfaces are free of dents and scratches, and that the operating panel is not scratched or cracked. The Barco Sales and Service ofce should be notied as soon as possible if this is not the case.
2.4 HDX ight case
Introduction of the HDX ight case
The HDX ight case is designed to transport the HDX projector in a safe and secure manner. The four caster wheels, provided with breaks, and the four handles make the HDX ight case easy to handle. The oor of the ight case wagon is equipped with two small covered compartments to store the remote control and the rigging clamps.
Image 2-3 HDX Flight case
Order number ight case: R9864090
The dimensions of the ight case are optimal for maximum utilization of the oor area of a truck. The cover of the HDX ight case has 4 stacking dishes, which allows to stack the ight cases.
WARNING: Maximum stack two (2) HDX ight cases high. Never higher.
2.5 Projector congurations
The different congurations
Depending on the installation the projector can be mounted in different ways, the different congurations are:
1. Front / Table (F/T)
2. Front / Ceiling (F/C) (upside down)
3. Front / Ceiling (F/C) (table positio
4. Rear / Table (R/T)
5. Rear / Ceiling (R/C) (upside down)
6. Rear / Ceiling (R/C) (table position)
Front projection
The projector is installed, either in a table mount or ceiling mount conguration, at the same side of the screen as the audience.
n)
16
R5905032 HDX SERIES 02/03/2015
Page 21
F/C
2. General
AUDIENCE
F/T
Image 2-4 Front projection
AUDIENCE
F/C
Image 2-5 Front proje ction, Ceiling mounted, in table position
SCREEN
FLOOR
SCREEN
FLOOR
Rear projection
The projector is installed, either in a table mount or ceiling mount conguration, at the other side of the screen opposite the audience.
AUDIENCE BACKSTAGE
R/C
R/T
Image 2-6 Rear projection
SCREEN
FLOOR
R5905032 HDX SERIES 02/03/2015 17
Page 22
2. General
Image 2-7 Rear projection, ceiling mounted in table position
Positioning the projector
AUDIENCE BACKSTAGE
R/C
SCREEN
FLOOR
SW
PD
SCREENSCREEN
SHB
SHB
ACD
SCREEN
CD
FLOOR
SW
Image 2-8 Positioning proj ector
The projector should be installed at right angles (horizontally and vertically) to the screen at a distance PD. Note the distance (A) between lens centre and table surface is slightly variable. This distance (A) is nominal 35 cm in case all feet are turned in completely and the vertical lens shift is set to zero (0).
On axis / off axis projection
The position of the projector with reference to the screen may also be different depending on the installation. Basically the projector can be positioned in On-Axis or Off-Axis conguration. On-Axis conguration means that the projector is positioned so as to have the centre of the lens coinciding with the centre of the screen. Off-Axis projection is obtained by shifting the lens up, down, left or right. Several parameters can be calculated determining the position in any installation.
Formula to calculate the distance CD for On-Axis projection: CD=SH/2+B-A
18
R5905032 HDX SERIES 02/03/2015
Page 23
2. General
Shift range
The lens can be shifted with respect to the DMD (P) which result in a shifted image on the screen (Off-Axis). A 100% shift means that the centre point of the projected image is shifted by half the screen size. In other words, the centre point of the projected image falls together with the outline of the image in an On-Axis projection. Due to mechanical and optical limitations it’s recommended to keep the shift values within the eld of view (F) as illustrated below. Within these shift ranges the projector and lens perform excellently. Conguring the projector outside these shift ranges will result in a slight decline of image quality.
U
-50% +50%
L R
D
Image 2-9 Vertical and horizontal shift range
PDMD. F Field of view.
It is mechanical possible to shift outside the recommended eld of view, but it will result in a decline of image quality depending on the used lens and the zoom position of the used lens. Furthermore, shifting too much in both directions will result in a blurred image corner.
Best image quality is projected in the On-Axis conguration.
+120%
-20%
F
P
F
P
P
F
U
D
L
R
SIDE VIEW
TOP VIEW
+120%
-20%
-50%
+50%
Horizontal and vertical projector tilt ranges
The projector can be rotated and mounted at any vertical angle. In other words, you can tilt the lens side of the projector as much as desired for your application.
Side to side tilt, however, must not exceed ±15°. This limit ensures that the lamp in the projector operates properly and safely. More tilting within area C is allowed but lamp icker can happen.
B
MAX
15°
15°
A
A
15°
15°
MAX
360°
C
Image 2-10 A Tilting allowed without problems B No tilting allowed in this area
R5905032 HDX SERIES 02/03/2015 19
Page 24
2. General
C Tilting allowed but lamp icker possible
Projector lamp will not start up when out of tilt range due to build-in tilt sensor.
2.6 Projector air inlets and outlets
Air inlets and outlets
Image 2-11
The HDX projector has 3 air inlet channels and 3 air outlets. The air outlets are located at the rear of the projector. The air inlets are located at the front of the projector.
2.7 Free download of Projector Toolset
About Projector Toolset
Projector Toolset is a software tool to set up, congure, manage and control Barco projectors.
The concept of this Projector Toolset software is modular. The basic package can be extended with several optional device plug-in modules, now and in the future available.
The Projector Toolset software works wi taken. A snapshot represents a current state of a conguration and can be reloaded to return to this typical state. These terms will be used through the complete software.
Projector Toolset is a stand-alone application that runs on a Java Virtual Machine and that does not require extra services to run.
Several congurations can be controlled simultaneously. Even when the congurations are connected via different ways.
Projector Toolset is only availa
Where to nd the download le(s)
The program and all necessary plug-ins, as well as the Reference manual can be downloaded for free from my.barco.com. Regis­tration is necessary.
th congurations that can be loaded. Within a conguration, different snapshots can be
ble in a download version, no CD can be ordered.
20
R5905032 HDX SERIES 02/03/2015
Page 25
1. Go to my.barco.com on https:\\my.barco.com.
2. Login on my.barco.com. If you are not yet registered click on Sign up for my.barco.com and follow the instructions. With the created login and pass- word, it is possible to enter the my.barco.com. When your login is correct, the my.barco.com start page is displayed.
3. Click the Support tab and follow the wizard to nd your projector. The Projector Toolset is located under the tab Application Software.
4. Download the Projector Toolset software package, which includes the device plug-in updates as well as the corresponding reference manual.
When downloading the complete Projector Toolset, this software contains already the latest device plug-ins. When you already have the latest core version of Projector Toolset, it is possible to download only device plug-in updates from the same web site location.
As Projector Toolset is a stand alone application, it is not necessary to install any other software. A Java virtual machine is included with this download.
Installation
Download rst the reference manual (Part number: R59770052) and follow the installation instructions as written in this manual.
2.8 Installation process overview
Quick setup
The following steps describe briey how to setup your HDX projector in a table mount front projection. Note that each step refers to a corresponding procedure, which is more detailed and illustrated.
1. Install the batteries of the remote control. See "RCU battery installation", page 23
2. Place the projector on a solid table in front of the screen at the expected throw distance. Ensure that the projector is installed at
right angles (horizontally and vertically) with the screen. See "Projector congurations", page 16.
3. Select and install an appropriate lens, which covers the throw ratio ( = screen size / projector screen distance). See "Lenses",
page 27.
4. Connect the projector with the local power net. See "Connecting the projector with the power net", page 38.
5. Connect your source to the appropriate input module. See "Input source connections", page 48.
6. Switch ON the projector. See "Power on projector", page 57.
7. Select the input slot to which the source is connected. Do this by pressing the numeric key on the remote control unit or on the
local keypad, See "Source selection", page 63.
8. Zoom and shift the lens until the image is properly projected on the screen, Do this by using the “ZOOM” and “FOCUS” key on
the remote control unit or on the local keypad. If necessary, level the projector from side to side by turning the adjustable feet in or out.
2. General
Check cooling liquid level at least every 6 months.
Every 6 months at device power up a message will be displayed on the local LCD to check the cooling liquid level
R5905032 HDX SERIES 02/03/2015 21
Page 26
2. General
22 R5905032 HDX SERIES 02/03/2015
Page 27
3. Physical installation
3. PHYSICAL INSTALLATION
About this projector
This chapter describes how the mechanical set up of the projector has to be done and how to realize the electrical connections.
Overview
Remote control unit (RCU)
Lenses
Connecting the projector with the power net
Alignment of a table mounted projector
Mounting the bottom carry handler
Mounting the top carry handler
Suspension of the projector with rigging clamps
Alignment of a ceiling mounted projector
3.1 Remote control unit (RCU)
Introduction
The remote control unit (A) of the HDX projector is equipped with a rugged case (B) and an XLR adaptor (C). The remote control unit can be used wired via mini-jack or via rugged XLR. Note that the backlight, of the remote control unit, illuminate continuously when wire connected.
Image 3-1 A Remote control unit (RCU). B Rugged case. C XLR adaptor.
Overview
RCU battery installation
RCU rugged case installation
RCU XLR adaptor installation
Using the XLR adaptor of the RCU
RCU usage possibilities
A
B
C
3.1.1 RCU battery installation
Where to nd the batteries for the remote control ?
The batteries are not placed in the remote control unit to avoid control operation in its package, resulting in a shorter battery life time. At delivery the batteries can be found in a separated bag attached to the remote control unit. Before using your remote control, install the batteries rst.
R5905032 HDX SERIES 02/03/2015
23
Page 28
3. Physical installation
How to install the batteries in the remote control ?
1. Push the battery cover tab with the ngernail a little backwards (1) and pull, at the same time, the cover upwards (2).
1
Image 3-2
2. Insert the two AA size batteries, making sure the polarities match the + and - marks inside the battery compartment.
+
-
Image 3-3
3. Insert (1) the lower tab of the battery cover in the gap at the bottom of the remote control, and press (2) the cover until it clicks
in place.
+
-
2
2
+
­+
Image 3-4
CAUTION: Replace with the correct battery type. Use two AA size batteries. There is a risk of explosion if the
battery is replaced with an incorrect type.
CAUTION: Replace the battery as explained above. There is a risk of explosion if the battery is incorrectly
installed.
3.1.2 RCU rugged case installation
How to install the rugged case of the remote control ?
1. Slide the bottom of the RCU into
1
-
the rugged case and then pull the top of the rugged case over the top of the RCU as illustrated.
24
R5905032 HDX SERIES 02/03/2015
Page 29
Image 3-5
3.1.3 RCU XLR adaptor installation
Install the rugged case before installing the XLR adaptor. Vice-versa, remove the XLR adaptor before removing the rugged case from the RCU.
3. Physical installation
Necessary tools
5mmat screw driver.
How to install the XLR adaptor of the remote control unit ?
1. Push the XLR adaptor (C) upon the rugged case of the remote control unit as illustrated.
Note: Ensure that the text of the XLR adaptor is on top.
C
S
Image 3-6
2. Fasten the two screws (S) of the XLR adaptor. Turn each screw repeatedly one or two turns until both screws are tight.
3.1.4 Using the XLR adaptor of the RCU
How to use the XLR adaptor of the remote control unit ?
1. Connect a cable with XLR plug into the XLR adaptor.
2. Connect the other end of the cable with your HDX projector.
3. Push the XLR adaptor completely a wired communication. Pull out the XLR adaptor (about 8 mm) to switch over to wireless communication.
gainst the rugged case of the remote control unit, as illustrated in the left image below, for
S
R5905032 HDX SERIES 02/03/2015
25
Page 30
3. Physical installation
Image 3-7
3.1.5 RCU usage possibilities
Summarized possibilities
Ref. Possibility description Comment
a.
RCU not wired
b. RCU wired (mini-jack) Backlight illuminates continuously when wire is connected. Infra red
c.
RCU with rugged case not wired
d.
RCU with rugged case wired (mini-jack) Backlight illuminates continuously when wire is connected. Infra red
e.
RCU with rugged case and XLR adaptor pulled out “REMOTE” and not wired
f. RCU with rugged case and XLR adaptor
pulled out “REMOTE” and wired
g.
RCU with rugged case and XLR adaptor pushed in “WIRED” and wired
disabled.
disabled.
The XLR adaptor must be in the pulled out position “REMOTE”, otherwise the RCU will not function.
The RCU will send the commands via infra red to the projector.
The RCU will send the commands via the cable connected with the XLR adaptor to the projector. Backlight illuminates continuously when wire is connected. Infra red disabled.
abcd fge
Image 3-8
26 R5905032 HDX SERIES 02/03/2015
Page 31
3.2 Lenses
Overview
Available lenses
Lens selection
Lens installation
Lens removal
Lens safety cable
Lens shift, zoom & focus
Scheimpug adjustment
3.2.1 Available lenses
Available lenses for the HDX projector projector
The TLD HB (High Brightness) lens series can be used on the HDX projector projector.
3. Physical installation
Image 3-9 R9852000:TLDHBxedlens(0.8:1)
Image 3-12 R9852010: TLD HB zoom lens (1.6 - 2.0 : 1)
Image 3-10 R9840770:TLDfixedlens(1.2:1)
Image 3-13 R9842080: TLD HB zoom lens (2.0 - 2.8 : 1)
Image 3-11 R9840775: TLD+ (1.2 : 1) xed lens
Image 3-14 R9862030: TLD HB zoom lens (2.8 - 4,5 : 1)
Image 3-15 R9842120: TLD HB zoom lens (5.0 - 8.0 : 1)
Image 3-16 R9862000: TLD+ lens (0.73 : 1)
Image 3-17 R9862005: TLD+ zoom lens (1.16 - 1.49 : 1)
R5905032 HDX SERIES 02/03/2015 27
Page 32
3. Physical installation
Image 3-18 R9862010: TLD+ zoom lens (1.5 - 2.0 : 1)
Image 3-21 R9862040: TLD+ zoom lens (4.5 - 7.5 : 1)
Image 3-19 R9862020: TLD+ zoom lens (2.0 - 2.8 : 1)
Image 3-22
R9829997: TLD+ zoom lens (7.5 - 11.0 : 1)
3.2.2 Lens selection
How to select the right lens
1. Determine the required screen width (SW).
2. Determine the approximate position of the projector in the room.
3. Start up the Lens Calculator on the Barco website: h for your conguration.
The Lens Calculator window opens.
Image 3-20 R9862030: TLD+ zoom lens (2.8 - 4.5 : 1)
ttp://www.barco.com/en/tools/lenscalculator to determine the possible lenses
28
R5905032 HDX SERIES 02/03/2015
Page 33
3. Physical installation
Image 3-23 Lens calculator
The Lens Calculator can also be used to determine the position of the projector when the lens type and screen width is known.
Due to lens tolerances the results of calculated values may be different from measured values. These differ­ence may vary +/- 5%.
3.2.3 Lens installation
How to install
1. Remove the foam rubber in the opening of the lens holder if not removed yet.
2. Take the lens assembly out of its packing material and remove the lens caps on both sides.
3. Place the lens holder in the “unlocked” pos illustrated.
ition by moving the lens lock handle (A) towards the lens power supply socket (B) as
B
A
Image 3-24 Lens installation, preparation
R5905032 HDX SERIES 02/03/2015 29
Page 34
3. Physical installation
4. Ensure that the lens holder stands in the On-Axis position (horizontal and vertical mid position).
Note: The lens holder is placed de fault in the O n-Axis po sition at factory.
5. Gently insert the lens in such a way that the lens connector matches the socket (B).
Image 3-25 Lens insertion
6. Insert the lens until the connector seats into the socket.
Warning: Do not r elease the Lens yet, as the Lens may fall out of the Lens Holder.
7. Secure the lens in the lens holder by sliding the lens lock handle into the “locked” position, which is away from the lens power supply socket. Ensure the lens touches the front plate of the lens holder.
Image 3-26 Lock lens
8. Check if the lens is really secured by trying to pull the lens out of the lens holder.
CAUTION: Never transport the projector with a Lens mounted in the Lens Holder. Always remove the Lens
before transporting the projector. Neglecting this can damage the Lens Holder and Prism.
3.2.4 Lens removal
How to remove
1. Support the lens with one hand while you unlock the lens holder by sliding the lock handle towards the “unlocked” position as illustrated.
30
R5905032 HDX SERIES 02/03/2015
Page 35
Image 3-27 Lens removal, unlock
2. Gently pull the lens out of the lens holder.
3. Physical installation
Image 3-28 Lens removal
It’s recommended to place the Lens caps of the original Lens packaging, back on both sides of the removed Lens to protect the optics of the Lens.
It’s recommended to place the foam rubber of the original projector packaging, back into the Lens opening to prevent intrusion of dust. Note that this foam rubber is packed in a plastic bag to prevent the dust, emitted by the foam, from entering the projector.
3.2.5 Lens safety cable
When using the safety cable ?
The lens safety cable must be used in any circumstances to protect a mounted lens in the lens holder when the projector is mounted above persons.
Necessary parts
Safety cable: R9801079 (Barco order number)
How to mount the cable
1. Put the safety cable around the lens. Make sure the cable is mounted between the motor part and the mounting ange
R5905032 HDX SERIES 02/03/2015 31
Page 36
3. Physical installation
2
1
Image 3-29 Lens safety cable
1 Lens motor block 2 Mounting ange 3Clamp
2. Insert both cable sides into the clamp; Strap the cable and make sure that the clamp is positioned on 45° from the bottom to avoid interference of the cable with the lens locking mechanism. Secure the cable by xating the nut of the clamp.
3
3
Image 3-30 Clamp position
3. Turn the cable with hook lock around the carry handle and hook the hook lock around the cable.
32
R5905032 HDX SERIES 02/03/2015
Page 37
Image 3-31
3.2.6 Lens shift, zoom & focus
3. Physical installation
Via Lens key
1. Press LENS key on the local keypad or the remote control.
The zoom/focus menu opens.
Image 3-32 Zoom/Focus adjustment
2. Use the or key to zoom the lens. Use the or key to focus the lens. Press ENTER to switch to Lens s
hift adjustment.
R5905032 HDX SERIES 02/03/2015
33
Page 38
3. Physical installation
Image 3-33 Shift adjustment
3. Use the or key to shift the lens in vertical direction. Use the or key to shift the lens in horizontal direction. Press ENTER to switch to zoom/focus adjustment.
Via direct access keys on the remote control
1. Press LENS FOCUS button [-] or [+] (C) for an overall focus of the image.
2. Press LENS SHIFT button for correct vertical position of the image on the screen.
3. Press LENS SHIFT button for correct horizontal position of the image on the screen.
Take into account that the lens focus may slightly drift while the lens is warming up from cold to operation temperature. This is a typical phenomenon for projection lenses used with high brightness projectors. The operation temperature of the lens is reached after approximately 30 minutes projection of average video.
3.2.7 Scheimpug adjustment
What has to be done ?
The lens holder has to be adjusted so that the “sharp focus plane” of the projected image falls together with the plane of the screen (Fp1Fp2). This is achieved by changing the distance between the DMD plane and the lens plane (Lp1Lp2). The closer the lens plane comes to the DMD plane the further the sharp focus plane will be. It can sometimes happen that you won’t be able to get a complete focused image on the screen due to a tilt (or swing) of the lens plane with respect to the DMD plane. This is also known as Scheimpug’s law. To solve this the lens plane must be placed parallel with the DMD plane. This can be achieved by turning the lens holder to remove the tilt (or swing) between lens plane and DMD plane (Lp3Lp4).
Lp1
Lp2
DMD
Image 3-34 Scheimpug principle
SCREEN
Fp1
Fp2
DMD
Lp3 Lp4
(Scheimpflug)
Fp4
Fp3
SCREEN
Scheimpug principle
The "plane of sharp focus" can be changed so that any plane can be brought into sharp focus. When the DMD plane and lens plane are parallel, the plane of sharp focus will also be parallel to these two planes. If, however, the lens plane is tilted with respect to the DMD plane, the plane of sharp focus will also be tilted according to geometrical and optical properties. The DMD plane, the principal lens plane and the sharp focus plane will intersect in a line below the projector for downward lens tilt.
34 R5905032 HDX SERIES 02/03/2015
Page 39
Scheimpug adjustment points
A
a
B
3. Physical installation
b
1
4
C
d
D
Image 3-35 Scheimpug adjustments
Indication on drawing Function
4 Locking nut
1, 2 and 3 Scheimpug adjustment nuts
A, B, C and D Set screws
a, b, c and d lock nuts
1, 2 and 3 are adjustment points.
4 is a locking point and NOT used during Scheimpug adjustment.
2
3
c
Necessary tools
Allenkey3mm
Nut driver 13 mm
Nut driver 10 mm
How to adjust
1. Project a green focus pattern.
Image 3-36
2. Loosen the lock nuts (a, b, c and d). See image 3-35.
3. Loosen the 4 set screws (A, B, C and D) by 1 cm. See image 3-35.
4. Fully loosen lock nut 4. See image 3-35.
R5905032 HDX SERIES 02/03/2015
35
Page 40
3. Physical installation
5. Optimize the focus of the projected image as follows:
a) Place the zoom lens in TELE position (smallest projected image) and adjust the focus using the lens focus barrel or motorized
focus control.
b) Place the zoom lens in WIDE position (largest projected image) and adjust the focus by turning equally on nut 1, 2 and 3.
c) Repeat steps “a” and “b” until the projected image is as sharp as possible.
F
1
Image 3-37 Center focusing
6. Sharpen bottom left corner of the screen by adjusting nut 1.
2
3
F
Image 3-38 Left bottom focusing
7. Sharpen bottom right corner of the screen by adjusting nut 2.
36
1
R5905032 HDX SERIES 02/03/2015
Page 41
Image 3-39 Right bottom focusing
8. Sharpen top right corner of the screen by adjusting nut 3
3. Physical installation
F
2
F
3
Image 3-40 Corner focusing
9. Repeat from step 6 until the projected focus pattern is as sharp as possible in the center, left, right, top and bottom of the screen.
How to xtheScheimpflug
Start the xation as follows (steps must be followed strictly) :
1. Turn in set screw A, B and C. Tighten lightly (by hand).
Tip: Any movem ent of the im age will affect the S cheimp ug adjustment
2. Fasten lock nuts a, b and c.
3. Turn in set screw D lightly (by hand) allowing the image to move slightly (1/3 to 1/2 of a square).
R5905032 HDX SERIES 02/03/2015
37
Page 42
3. Physical installation
Image 3-41
4. Fasten lock nut d.
5. Tighten nut 4 until the offset of the image movement created in step 3 is canceled.
Tip: The amount of image movement in step 3 w ill determine how tight the nut in step 5 will need to be turned to return the
image to its original position.
3.3 Connecting the projector with the power net
1/3 to 1/2
CAUTION: Use only the power cord provided with the projector.
How to connect with local power net
1. Ensure that the power switch stands in the ’0’ (OFF) position (1).
1
2
3
Image 3-42 Power input
2. Connect the female side of the power cord with the power input socket of the projector (2).
3. Secure the power plug by locking the plug holder clamp (3).
38
R5905032 HDX SERIES 02/03/2015
Page 43
3. Physical installation
4. Connect the male side of the power cord to the local power net.
Caution: E nsure that the power net meets the power requirements of the projector.
WARNING: Do not attempt operation if the AC supply and cord are not within the specified voltage and power
range.
CAUTION: Once the projector is switched to standby, the lamp cooling fans will continue to run for approx-
imately ve minutes to ensure that the projector and lamp have sufciently cooled, at which point the fans will automatically decrease to standby. To avoid thermal stress that can lead to premature lamp failure, never unplug the power cord while the lamp cooling fans are running. Never unplug the power cord to power down the projector, rst switch off the power switch and then unplug the power cord.
Fuses
The projector is protected with an automatic circuit breaker of 20 A which is built into the power sw
The voltage meter is protected with a fuse (1A) which is located on the neutral bonding cable. If necessary to replace this fuse, consult a service technician.
itch.
3.4 Alignment of a table mounted projector
How to align
1. Place the projector in the desired location. Take into account the zoom range of the used lens and the size of the screen.
2. Project one of the internal hatch patterns on the screen.
3. Turn the adjustable feet in or out until the projected hatch pattern has a perfect rectangle shape and is leveled.
Image 3-43 Level alignment
When this is achieved, the projector is set horizontal and vertical at right angles to the screen.
SCREEN
Image 3-44 Angle adjustment
3.5 Mounting the bottom carry handler
Necessary tools
Open wrench 17 mm
Necessary parts
4x bolt M10 x 16 mm
R5905032 HDX SERIES 02/03/2015
SCREEN
39
Page 44
3. Physical installation
How to mount
1. Turn the projector upside down.
2. Turn out the 4 feet.
Image 3-45 Remove feet
3. Turn out the feet of the carry handle as far as possible.
Image 3-46 Mount carry handle
4. Place the carry handle on the projector as illustrated. Adjustment knob to the back of the projector. Make sure that the mounting holes matches the holes in the projector.
5. Insert a bolt in each corner and turn in these bolts.
40
R5905032 HDX SERIES 02/03/2015
Page 45
2
1
Image 3-47 Insert bolts
3.6 Mounting the top carry handler
Purpose
This carry handle can be used to transport the projector in an easy way.
3. Physical installation
Necessary tools
8 mm Allen wrench
Necessary parts
4x bolt M10 x 16
4x washer
1x carry handler
How to mount
1. Place the carry handle on top of the projector so that the xation holes match the holes in the projector.
1
1
Image 3-48 top carry handle
2. Turn in the 4 xation bolts (1)
R5905032 HDX SERIES 02/03/2015 41
. Insert a washer between the bolt and the carry handle.
Page 46
3. Physical installation
3.7 Suspension of the projector with rigging clamps
Rigging points and rigging clamps
When a carrying handle is mounted at the bottom side of the projector, eight slots are available to mount rigging clamps. Four slots are longitudinally (1) oriented and four slots are transversely (2) oriented. Each slot contains a rigging point of which the position in the slot can be adjusted depending on the size of the truss installation. The rigging clamps can be attached to those rigging points, which allows an easy and fast physical setup of the projector in a hanging conguration.
1
2
Image 3-49 Rigging points
Necessary tools
Open end spanner 24 mm
Open end spanner 17 mm
Necessary parts
4 rigging clamps
How to install and use the rigging clamps
1. Measure the distance, center tube as reference, between the two used support bars of the truss.
X mm
Image 3-50 Truss, example
2. Turn the projector upside down and slide the rigging points on there place in the slots, according the measured distance and secure this position. To release the nuts of the rigging points use a 24 mm open ended spanner. Ensure that the rigging points are symmetrically lined up, so that the projector will hang in balance.
Warning: Be careful while working with heavy loads.
Warning: Always secure the rigging points after adjustment.
X mm
Image 3-51 Rigging points, distance
42 R5905032 HDX SERIES 02/03/2015
Page 47
3. Physical installation
3. Turn in the rigging clamps into the rigging points using a 17 mm open ended spanner and secure the rigging clamps by turning the safety nut on the rigging clamp against the rigging point using a 17 mm open ended spanner.
Image 3-52 Mount rigging clamps
Warning: Always us e four (4) rigging points, equally spread, to suspend the projector.
4. Place all four rigging clamps in open position.
5. Place the projector (upside down) under the truss installation and lower the truss until the support bars of the truss are nearby the rigging clamps mounted on the projector.
Image 3-53 Mount to truss
6. Lift up the projector and hook the four rigging clamps over the support bars of the truss.
R5905032 HDX SERIES 02/03/2015
43
Page 48
3. Physical installation
7. Lock all four rigging clamps by turning the xation handle clockwise.
Image 3-54 Clamp xation
8. Install the 2 safety cables, one on both sides of the carrying handle, and around the truss. Mount the 2 safety cables around the carry handle (push the hook through the loop and then aroun to much play (maximum 20 cm). If necessary turn the cable a few times around the truss before clasping the safety hook around the cable.
d the truss so that there is not
Image 3-55 Security cables
9. Lift up the truss with the attached projector to the desired height.
Mount the 2 safety cables in such a way that when something goes wrong, the projector cannot fall more than 20 cm. If necessary, turn the cables a few times around the truss to obtain this maximum distance.
3.8 Alignment of a ceiling mounted projector
Necessary tools
17 mm open spanner
Skew adjustment
1. Turn the adjustment knob on the carry handle until the projected hatch pattern is perfectly squared.
44
R5905032 HDX SERIES 02/03/2015
Page 49
Skew
Image 3-56 Skew adjustment
Tilt adjustment with the clamps
1. Adjust both front side clamp or both back side clamps to adjust the tilting.
Always adjust by two to avoid deformation of the frame.
2. Loosen the security nut on both clamps.
3. Adjust the adjustment nuts of both clamps until the desired tilting is reached.
4. Turn the safety nut on the rigging clamp against the rigging point
3. Physical installation
R5905032 HDX SERIES 02/03/2015 45
Page 50
3. Physical installation
46 R5905032 HDX SERIES 02/03/2015
Page 51
4. Input & Communication
4. INPUT & COMMUNICATION
Overview
Introduction
Input source connections
Communication connections
Utility-Accessory Outlet
4.1 Introduction
General
The Input & Communication side of the projector consists of a button module, a dual 3G/HDSDI and DVI-I input as standard input module and 2 free input slots. The free input slots can be used for optional modules (e.g. 5-cable input).
1
2
3
4
5
6
7
8
Image 4-1 Input & Communication connections
1 Display
2 Optional antenna for Wiconnection
3 12 V output as power supply to external equipment
4 DMX in - out
5
XLR input port for remote control
6 RS232/RS422 input port
7
Dual Link DVI-I HDCP input
8 Free input slot
9 Button module
10 Optional antenna for GSM
11 RS232/RS422 input port
12 Ethernet port
13 Status and indication LEDs
14 USB port
15 3G/Dual/HDSDI input - output
16 Free input slot
9
10
11
12
13
14
15
16
R5905032 HDX SERIES 02/03/2015
47
Page 52
4. Input & Communication
4.2 Input source connections
DVI and 3G/HDSDI input
This input module is standard delivered with the HDX projector.
DUAL LINK DVI-I HDCP
SEL SYNC
INPUT
Image 4-2 Dual Link DVI and 3G/Dual HDSDI input
The yellow LED lights up when valid input sync is detected.
The green LED lights up when the input is selected.
DVI input specications :
RGB analog : up to 170 MHz.
Single DVI : up to 165 MHz
Dual link DVI : up to 210 MHz
DVI will not natively support 10-bit or 12-bit deep color. It is possible to enable 30-bit color over DVI using a specic pixel packing. We support the pixel-packing that is implemented by Silicon Image Sil7189 DVI re­ceiver.
3G/Dual HDSDI input specications :
3G follows the SMPTE 425M standard.
HDSDI follows he SMPTE 292M standard.
Dual link follows the SMPTE 372M standard
SDI follows the 259M standard
5-cable input (optional)
Optional multi purpose input which can be inserted in the free slots.
IN1
SEL
SYNC
3G/DUAL HDSDI
OUT1
IN2
SEL
SYNC
R9864000
OUT2
V/C
R
R9864010
SEL
SYNC
Image 4-3
BARCO
R/PR G/Y/VIDEO
5-CABLE INPUT
B/P
B
H/S
Signal connectivity
Input signal
RGBHV
RGBS
RGsB
RGBCV
Composite Video
Super Video
Component Video
R/P
R
R
R
R
R
PR/(R-Y)
G/Y/VIDEO B/ P
G
G
Gs
sync on green
G
VIDEO
Y
Luma
Y
BHV
B
B
B
———
——
PB/(B-Y) S
B
-S
Component Video
PR/(R-Y)
Ys
PB/(B-Y)
-SOY
YUV-CV R-Y Y B-Y CV
5-cable input specications :
H/S V/C
S
R
——
CV
-
C
Chroma
——
-
48
R5905032 HDX SERIES 02/03/2015
Page 53
4. Input & Communication
Data and HD sources RGB and YUV [HS/VS, CS or SOG(Y)]:
- Pixel clock maximum 210 MHz
- 8 bit digital output
Video sources CVBS, S-VIDEO, RGB and YUV [CS, CV or SOG(Y)]:
- PAL B/D/I/G/H, PAL60, PAL M, PAL N, PAL Nc
- NTSC M/J, NTSC 4.43
- SECAM B/D/G/K/L
- 525i, 625i, 525p, 625p
- Macrovision copy protection robust
- Standard images “video525” and “video625”
Automatic detection of sync inputs but with manual override:
- automatic modes : RGB, YUV, VIDEO
- manual modes : RGB HS/VS - CS, RGB CV, RGB SOG, YUV HS/VS - CS, YUV CV, YUV SOY, CVBS, S-VIDEO
Possible to disconnect 75 Ohm terminations on HS and VS (TTL sync level selection)
Signal requirements:
- Component Video (BNC)
o
R-Y : 0,7Vpp ±3dB 75 Ohm termination.
o
Ys : 1Vpp ±3dB (0,7V Luma +0,3V Sync) 75 Ohm termination.
o
B-Y : 0,7Vpp ±3dB 75 Ohm termination.
-RG(s)B
o
R : 0,7Vpp ±3dB 75 Ohm termination.
o
G(s) : 1Vpp ±3dB (0,7Vpp G + 0,3Vpp Sync) 75 Ohm termination.
o
B : 0,7Vpp ±3dB 75 Ohm termination.
Diagnostic LED’s on front panel:
- Green LED: Lights up in case input module is selected
- Yellow LED: Lights up in case sync detected
3D Input Module (optional)
Optional 3D input which can be inserted in the free slots.
BARCO
3D SYNC IN
Image 4-4
Signal connectivity
3D SYNC IN
BNC socket to apply an external 3D synchronization signal. Used for sequential modes. If signal is not present an internal 3D sync is generated.
DISPLAYPORT
DisplayPort connector to connect a video source.
DisplayPort selection LED + sync LED
SEL: lights up if the DisplayPort is selected. SYNC: lights up if the applied source has a valid DisplayPort sync.
HDMI
Connector for HDMI cable (with optional locking mechanism).
HDMI selection LED + sync LED
SEL: lights up if the HDMI input port is selected. SYNC: lights up if the applied source has a valid HDMI sync.
3D SYNC OUT
BNC socket. Generates 3D synchronization signal to drive an infra red transmitter for active 3D glasses. In case an 3D syn­chronization signal is applied on the “3D SYNC IN” for a single channel 3D stream then the generated 3D output sync is derived from this applied sync.
Input specications
DISPLAYPORT HDMI
3D INPUT
SEL
SYNC
SEL
SYNC
R9864140
3D SYNC OUT
R5905032 HDX SERIES 02/03/2015
49
Page 54
4. Input & Communication
HDMI (High-Denition Multimedia Interface)
HDMI 1.4a up to 210MHz pixel clock. Support for ‘Deep Color’ up to 12 bit per color.
DisplayPort
DisplayPort 1.1a up to 210 MHz pixel clock. Support for ‘Deep Color’ up to 12 bit per color.
In all cases, the minimum input frequency for 3D is 23 Hz per eye. Below this frequency the image will not be displayed correctly.
4.3 Communication connections
Communication interface
DMX
IN
/1A
12V
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Image 4-5 Communication interface, indications
1 12V 1A output
2
DMX interface (input, output)
3 XLR input
4
RS232 input
5
USB port
6 Ethernet port
7
Ethernet type indication
8 Ethernet activity indication
9 Error indication
10 Power indication
11 IR indication
12 Lamp indication
13
ACT (activity) indication
14
Wiselect indication
15 IR receiver
OUT
REMOTE CTRL
1
2
3
RS232/422 IN
USB
10/100 BASE-T
ETH ACT
10/100
PWR LMP
ERR
WIFI
SEL
IR ACT
15
12V output
12 V output, maximum 1A, available when projector is not in stand by.
DMX interface
DMX is used as communication bu the bus can be looped between the different devices. According the standard a ve wire cable with XLR connector is used.
You can use the DMX input port to connect a DMX device (DMX console) to the projector. This way you can control the projector from that DMX device (console). The DMX output port can be connected with the next device in the loop.
Pin Description
1Earth
50
s between different devices in the light technic. Each device has an input and an output, so that
R5905032 HDX SERIES 02/03/2015
Page 55
4. Input & Communication
Pin Description
2
3Hot
4
5
DMX
DMX-512 Lighting protocol over RS-485 interface. Carries information of 512 channels from a lighting con lighting devices. Standardized by USITT.
Cold
Return - (or not used)
Return + (or not used)
Wired remote control (XLR)
If desired the remote control unit can be wired and plugged in into the male XLR port on the communication interface.
XLR – Remote CTRL in
Pin Description
1
GND
2
RC5 in
3 XLR present sense
troller to
RS232/RS422 input
The communication interface of the HDX projector supports RS232 and RS422 serial communication on two different types of input connectors. The left one a Sub-D connector, the right one an USBB connector acting as RS input when connected to an USB input of a PC.
You can use the RS232/RS422 input to connect a local PC to your HDX projector. By this way you can congure and control your HDX projector from your local PC.
Do not forget to set the projector’s baud rate to match that of the computer.
Advantages of using RS232/RS422 serial communicatio
easy adjustment of the projector via PC (or MAC).
allow storage of multiple projector congurations and set ups.
wide range of control possibilities.
address range from 0 to 255.
sending data to the projector (update).
copying data from the projector (backup).
RS232/422 input (Sub-D) port
Pin Description
1
DCD : Data Carrier Detect
2RXD-:ReceiveData
3 TXD- : Transmitted Data
4
DTR : Data Terminal Ready [RS232]
TXD+ : Transmitted Data [RS422]
5
GND : Ground
6
DSR : Data Set Ready [RS232]
RXD+ : Received Data [RS422]
7
— (not connected) —
8
CTS : Clear To Send
9 RI : Ring Indicator
n:
R5905032 HDX SERIES 02/03/2015
51
Page 56
4. Input & Communication
RS232
An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the commu­nication path between two devices using either D-SUB 9 pins or D-SUB 25 pins connectors. This standard is used for relatively short-range communications and does not specify balanced control lines. RS-232 is a serial control standard with a set number of conductors, data rate, word length and type of connector to be used. The standard species com­ponent connection standards with regard to computer interface. It is also called RS-232-C, which is the third version of the RS-232 standard, and is functionally identical to the CCITT V.24 standard. Logical ’0’ is > + 3V, Logical ’1’ is < ­3V. The range between -3V and +3V is the transition zone.
RS422
An EIA serial digital interface standard that species the electrical characteristics of balanced (differential) voltage, digital interface circuits. This standard is usable over longer distances than RS-232. This signal governs the asyn­chronous transmission of computer data at speeds of up to 920,000 bits per second. It is also used as the serial port standard for Macintosh computers. When the difference between the 2 lines is < - 0.2V that equals with a logical ’0’. When the difference is > +0.2V that equals to a logical ’1’..
USB port
The communication interface is equipped with a master USB port, type “A” connector. This USB port will simplify the service pro­cedures for software updates or for taking backup les from the projector without network connection. An USB-stick is plugged into the USB port and les can be transferred from or to the projector using the local or remote control unit. Note that the USB-stick has to be Linux FAT16 compatible.
Ethernet port
The projector can be connected to a LAN (local area network) using the Ethernet port on the communication interface. Once con­nected to the LAN, users are capable of accessing the projector from any location, inside or outside (if allowed) their company network using the control software: Projector Toolset. This toolset locates the projector on the network in case there is a DHCP server or the user can insert the correct IP-address of the projector to access the projector. Once accessed, it is possible to check and manipulate all the projector settings. Remote diagnostics, control and monitoring of the projector can then become a daily and very simple operation. The network connectivity permits to detect potential errors and consequently improve the time to servicing.
The connector used for the Ethernet ports (E) are of rugged Neutrik EtherCon RJ45 type, which is compatible with standard RJ45 cable connector. Straight (most common) as well as cross linked network cables can be used.
10/100 Base-T — RJ45 port
Pin Description
1TXD+
2TXD-
3RXD+
4
5
6RXD-
7
8
Status lights
Function Color Description
ETH act
10/100
IR red IR received but not acknowledged
WIFI sel
ACT
ERR red See chapter “Getting started”, topic “Status LEDs
green
orange
green
orange
green
When connected with an Ethernet
When a 100 MB network is detected
IR received and acknowledged
When WiFi is selected
When WiFi is connected with an Ethernet
52
R5905032 HDX SERIES 02/03/2015
Page 57
4. Input & Communication
Function
PWR
LMP
Color
orange
orange
Description
See chapter “Getting started”, topic “Status LEDs
See chapter “Getting started”, topic “Status LEDs
4.4 Utility-Accessory Outlet
What can be done ?
An extra DMX controlled accessory can be added to projector.
Some examples of the use of this connector:
Connect external accessories like the Catalyst Mirrorhead (Even if this example still needs a extra Power supply
Connect other DMX enabled devices like, color changers, shutters, dimmer wheels
Connect a DMX Lens option
Connect a DMX rigging frame level device
Use for external relay
Image 4-6 Utility-accessory outlet
Pin conguration
1
GND
2DMXData–
3DMXData+
4
Power 9 - 24 Volt DC With Setting in menu 9 / 12 / 24 @ 25W
Note : do not overload ! Maximum 1A on 24V is allowed.
The connector is a duplicated output of the DMX signal entering the projector over the 5 Pin XLR
R5905032 HDX SERIES 02/03/2015
53
Page 58
4. Input & Communication
54 R5905032 HDX SERIES 02/03/2015
Page 59
5. GETTING STARTED
Overview
RCU & Local keypad
Terminology overview
Power on projector
Switching to standby
Power off projector
Status LEDs
Using the RCU
Projector Address
Source selection
5.1 RCU & Local keypad
How controlling the projector ?
The projector can be controlled by the local keypad or by the remote control unit.
Location of the local keypad ?
The local keypad is located on the input side of the projector.
5. Getting started
Remote control functions.
This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set up.
Other functions of the remote control are :
switching between stand by and operational mode.
switching to "pause" (blanked picture, full power for immediate restarting)
direct access to all connected sources.
5.2 Terminology overview
Overview
The following table gives an overview of the different functionality of the keys.
R5905032 HDX SERIES 02/03/2015
55
Page 60
5. Getting started
23
1
5
1
(
7
7
%
*
$
3
2
5
3
,
3
:
2
'
1
,
:
22
21
20
10
2
1
6
7
RGB
PATTERN
STBY
PAUSE TEXT
7
2
Image 5-1 Local keypad and RCU
61
4
3
89
WINDOW
PIP
AUTO
2016
3
MENU
EXIT
4
10
11
5
TEXT
PHASE
SHARPN
TINT
COLOR
BRIGHTN
CONTR
LENS SHIFT
LENS
SHIFT
ENTER
6
LENS
7
8
9
PAUS E
*
*
$
1
,
*
*
,
5
(
0
,
2
7
8
$
0
9
8
7
6
5
3
4
2
1
LENS
ZOOM
LENS
FOCUS
19
EXIT
5
3 18
MENU
0
LENS
FN
821
9
ENTER
5
17
19
18
17
16
15
14
13
12
Ind. Key name Description
1 Pattern key Direct access key to the internal pattern selection menu.
2 RGB Toggle key to enable and disable colors in the adjustment mode. Toggle between red,
green, blue and full RGB.
3 MENU Access key to the menu structure and key to quickly quit the adjustment menus.
4 Address key (recessed key), to enter the address of the projector (between 0 and 9) in the remote
control. Press the recessed address key with a pencil, followed by pressing one digit button between 0 and 9.
5
LENS
Direct access key to the lens adjustment menus. Toggling this key will change the projected pattern.
6
PAUSE To stop projection for a short time, press ’PAUSE’. The image disappears but full power
is retained for immediate restarting. Shutter is closed.
7
STBY Standby function switch off the lamp and lamp electronics. The lamp cooling fans remain
active for about 5 minutes. The speed of the other fans is reduced.
8F
N
9Auto
FN toggles the local display to preview an input
Auto alignment at rst access.
10 Digit buttons Direct input selection or numeric entries
11
Lens zoom/focus Zoom and focus controls of the lens
12
Lens shift Shift control of the lens, to shift the lens up/down or left/right
13 Picture controls Use these buttons to obtain the desired picture level.
14
PHASE Used to remove the horizontal instability of the image (usually for RGB source). It adjusts
the phase of the pixel sampling clock relative to the incoming signal.
15 FREEZE
To freeze the actual projected image.
56
R5905032 HDX SERIES 02/03/2015
Page 61
5. Getting started
Ind. Key name Description
16 TEXT Toggle key to activate or deactivate on screen text boxes while adjusting a setting.
When adjusting one of the image controls, e.g. during a meeting, the normally displayed bar scale can be deactivated by pressing ’TEXT’ key rst. To re-display the bar scale on the screen, press ’TEXT’ key again. When TEXT is ’off’, no adjustment menu’s will be displayed on the screen when entering the adjustment mode. All menus and adjustments remain active on the local LCD panel.
17 ENTER
18
Cursor keys
19 EXIT Key to go one menu stage higher than the actual position when in the adjustment mode.
20
WINDOW Selection of the active window “Main” or “PiP”
21 PIP
22
Info Displays help information when on a certain menu item of the sofrware
23
RC Operating indication Lights up when a button on the remote control is pressed. (This is a visual indicator to
Ta bl e 5 -1
Key to conrm an adjustment or selection in the adjustment mode.
To make menu selections when in the adjustment mode
Direct access key for picture in picture selection.
check the operation of the remote control)
5.3 Power on projector
How to power on.
1. Press the power switch at the back of the projector to switch on this projector.
Image 5-2 Main switc h
- When ’0’ is pressed, the projector is switched off.
- When ’1’ is pressed, the projector is switched on.
The projector starts up in standby. The menus are accessible via the local LCD panel.
The start up screen is displayed on the local LCD panel and when fully started up, it changes to the overview screen.
R5905032 HDX SERIES 02/03/2015
57
Page 62
5. Getting started
Image 5-3 Start up screen, Main
This screen indicates :
- the selected Main input
- the selected PIP input
- the IP address
- the Customer Id
- the Lamp status
- the Mains voltage
- the current ambient temperature
- the Text status (OSD)
To display an image, the standby key must be pressed once.
The current mains input voltage is indicated on the voltmeter just above the power switch.
The background image of the startup screen and info screens can be changed with Projector Toolset with an installed HDX plug-in.
Lamp overview
Once the projector is started, press Lamp to get an overview of the lamp parameters such as :
Image 5-4 Local screen, lamp
58 R5905032 HDX SERIES 02/03/2015
Page 63
5. Getting started
number of Strikes
Run time in hours
Remaining run time in hours
slide bar indication with percentage indication of the current run time, compared with the maximum life time of the lamp.
Software overview
Once the projector is started, press About to get an overview of the software versions such as :
Image 5-5 Local screen, about
Package version
•Mgrsoftware
GUI software
Starting image projection via the standby key.
1. Press Stand by key once on the local keypad or on the remote control.
R5905032 HDX SERIES 02/03/2015 59
Page 64
5. Getting started
5
1
3
,
3
:
2
'
1
,
:
(
7
7
%
*
$
3
5
3
2
1
6
RGB
STBY
Image 5-6 Standby key indication
7
PATTERN
PAUS E
89
WINDOW
TEXT
AUTO
MENU
LENS
PAUSE
*
*
$
1
(
,
0
,
*
2
4
5
MENU
EXIT
0
PIP
LENS
Fn
ENTER
*
,
7
5
8
$
0
9
8
7
6
5
3
4
2
1
LENS
ZOOM
LENS
FOCUS
TEXT
PHASE
SHARPN
TINT
COLOR
BRIGHTN
CONTR
LENS SHIFT
LENS
SHIFT
EXIT
ENTER
The projector starts up on the last saved source. The LMP LED on the communication interface lights up.
Some lamp and runtime warnings can be displayed when an image is displayed after a start up.
5.4 Switching to standby
How to switch to standby
1. Press and hold Standby for 3 seconds on the local keypad or the remote control. In the mean time the message Keep on pressing... is displayed. This message changes to Saving data ...
The projector goes to standby.
All custom settings are written to the internal backup device. A message ’Saving data ...’ indicates this process. Never switch off the projector while this message is displayed.
When switching to standby, an after cooling process will start to cool down the projector. The after cool time depends on the temperature inside the projector and can vary from 30 second to 5 minutes.
5.5 Power off projector
How to power off
1. Press rst Standby.
2. Let cool down the projector until the fan speed decreases. At least 5 minutes.
3. Switch off the projector with the power switch. ’0’ must be pressed.
60
R5905032 HDX SERIES 02/03/2015
Page 65
CAUTION: Never switch off the projector while the message ’Saving data ... ’ is displayed !
5.6 Status LEDs
Overview
LED
Standby button
Pause button
PWR (power LED)
LMP (lamp LED)
ERR (error LED)
Color status
Red on Projector is in standby
Red toggles on/off Projector startup failed, no lamp power supply
Green toggles on/off
Green on
Orange toggles on/off Projector is on, lamp power supply is off
White toggles on/off From/To ECO standby
Dimmed white Projector powers up
Red on
Green on Shutter is open
Dimmed white
Full white
Full white toggles on/off
Off Projector powers up
Red Standby
Orange ECO standby
Green Projector is on
Off Lamp is off
Red No lamp inserted
Orange Lamp is on in ECO mode
Green Lamp is on in normal mode
Green-Orange Lamp is on in CLO mode
Off No error
Red toggles on/off Error
Orange toggles on/off Warning
Red IR signal receivedIR
Green IR signal acknowledged
5. Getting started
Description
Projector starts up
Projector is on
Shutter is closed
Shutter is closed, projector in standby
Shutter is undened (shutter not open and not closed)
Shutter is closed during reset formatter
5.7 Using the RCU
Pointing to the reective screen
1. Point the front of the RCU to the reective screen surface.
R5905032 HDX SERIES 02/03/2015
61
Page 66
5. Getting started
F1
AD J
F2
90
PA
F3
7
US
5
E
34
1
F4
8
6
TR EB
BA
2
LE
TE
SS
F5
XT
EX
PH
IT
SH
EN
AS
AR
TE
E
TI
CO
R
PN
NT
BR
LO
IG
CO
BA
R
HTN
NTR
LA
VO
NC
L
E
Image 5-7 IR control via reective screen
Hardwired to the XLR input
1. Plug one end of the remote cable in the connector on the bottom of the RCU.
2. Plug the other end in the big connector on the communication interface of the projector, labelled Remote CTRL.
Pointing directly to the IR sensor
When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line). The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control unit and the projector IR sensor.
45°
Image 5-8 RCU to one of the IR sensors
45°
F3
F2
F4
F1
F5
AD
J
EX
IT
EN
TER
P
A
US E
TE
X
T
PH AS
E
90
SH AR
PN
7
8
TI
NT
6
5
CO LO
R
34
BR IG
HT
N
2
1
CO
NT R
TR EB
LE
BA LA
NC
E
BA
SS
VO
L
45°
45°
F3
F2
F4
F1
F5
AD
J
EX IT
EN
TE R
PA
US
E
TE
XT
PH
AS E
90
SH
AR
PN
7
8
TI
NT
6
5
CO
LO
R
34
BR
IG
HT
N
2
1
CO
NT R
TR EB
LE
BA
LA
NC E
BA
SS
VO
L
45°
45°
F3
F2
F4
F1
F5
AD J
EX IT
EN TE
R
PA
US E
TE
XT
PH AS
E
90
SH AR
PN
7
8
TI
NT
6
5
CO
LO
R
34
BR IG
HT
N
2
1
CO NT R
TR EB
LE
BA LA
NC
E
BA
SS
VO
L
62 R5905032 HDX SERIES 02/03/2015
Page 67
5.8 Projector Address
5.8.1 Displaying and Programming addresses into the RCU
Displaying the Projector Address on the Screen.
1. Press Address key (recessed key on the RCU) with a pencil.
The projector’s address is displayed on the local LCD screen.
To continue using the RCU with that specic address, it is necessary to enter the same address with the digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the Address key displays projector address 3, then press "3" digit button on the RCU to set the RCU’s address to match the projector’s address. Do not press 03. This will address the remote control to ’0’ and control all projectors in the room. If the address is not entered within 5 seconds, the RCU returns to its default address (zero address) and controls all projectors in the room.
How to Program an Address into the RCU?
1. Press the Address key (recessed key on the RCU) with a pencil.
2. Enter the address with the digit buttons within 5 seconds after pushing the address key.
Note: That address can be any digit between 0 and 9.
The LED on the remote control must lit up while pressing a digit key. Otherwise the address is not entered in the remote control.
5. Getting started
5.8.2 Controlling the projector
Projector address
Address installed in the projector to be individually controlled.
Common address
Projector will always execute the command coming from a RCU programmed with that common address.
Why a projector address ?
As more than one projector can be installed in a room, each projector should be separately addressable with an RCU or computer. Therefore each projector has its own address.
Set up an individual Projector Address.
The set up of a projector address can be done via the software. See chapter ’Projector Control’, ’Projector address’.
Projector controlling.
Every projector requires an individual address between 0 a
When the address is set, the projector can be controlled now:
RCU for addresses between 0 and 9.
computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255.
nd 255 which can be set in the Service mode.
Common Address
Every projector has a common address ’0’ or ’1’. The c address Common address.
hoice between ’0’ and ’1’ can be selected in P rojector Control Projector
5.9 Source selection
Source selection when no picture in picture is active
Use the digit keys on the remote control or local keypad to activate the desired source.
R5905032 HDX SERIES 02/03/2015
63
Page 68
5. Getting started
Source selection when picture in picture is active
Use the Window button on the remote control or the local keypad to select the main window or the picture in picture (PiP) window.
5
1
3
,
3
:
2
'
1
,
:
(
7
7
%
*
$
3
5
3
2
1
6
RGB
STBY
Image 5-9 Window selection button
7
PATTERN
PAUS E
89
WINDOW
TEXT
AUTO
MENU
LENS
PAUSE
*
*
$
1
(
,
0
,
*
2
4
5
MENU
EXIT
0
PIP
LENS
Fn
ENTER
*
,
7
5
8
$
0
9
8
7
6
5
3
4
2
1
LENS
ZOOM
LENS
FOCUS
TEXT
PHASE
SHARPN
TINT
COLOR
BRIGHTN
CONTR
LENS
SHIFT
LENS SHIFT
EXIT
ENTER
The outline of the selected window gets a colored rectangle to indicate the selection. For the main window, the color is blue. For the picture in picture window, the color is orange.
Once the desired window is activated (main window or picture in picture window) all keys on the remote control or local keypad can now control that selected window.
To select the source for the picture in picture window, press Window button until PiP window is activated and then select the desired source with the digit keys.
To select the source for the main window,
press Window button until the main window is activated and then select the desired source
with the digit keys.
64
R5905032 HDX SERIES 02/03/2015
Page 69
6. Quick set up adjustment
6. QUICK SET UP ADJUSTMENT
Overview
Text boxes ON or OFF
Quick Lens Adjustment via LENS key
Direct Lens Adjustment (RCU)
Quick picture in picture
Quick language selection
6.1 Text boxes ON or OFF
Text toggle function
The on-screen text boxes can be switched OFF so that an adjustment during the operation of the projector is not visible on the screen. The adjustment indication remains visible on the local LCD screen.
4
PIP
AUTO
5
0
LENS
FN
1
MENU
EXIT
ENTER
1
1
6
RGB
STBY
Image 6-1 Text button
2
7
PATTERN
PAUSE TEXT
3
89
WINDOW
To toggle Text ON or OFF, press the TEXT key on the remote control or local keypad.
6.2 Quick Lens Adjustment via LENS key
Quick zoom/focus adjustment
1. Press the LENS key on the remote con
trol or local keypad to open the Zoom/Focus Adjustment menu.
*
5
MENU
5
1
(
7
7
%
$
3
PAU SE
*
$
(
0
,
2
7
8
$
LENS
3
,
3
TEXT
PHASE
2
'
1
,
:
EXIT
ENTER
:
R5905032 HDX SERIES 02/03/2015 65
Page 70
6. Quick set up adjustment
4
3
2
1
6
RGB
STBY
7
PATTERN
PAUSE TEXT
89
WINDOW
PIP
AUTO
5
0
LENS
FN
MENU
EXIT
ENTER
*
5
MENU
5
1
(
7
7
%
$
3
3
,
3
1
,
'
:
EXIT
:
2
Image 6-2 Lens button
1
1
LENS
PAU SE
*
$
(
0
,
2
7
8
$
ENTER
TEXT
PHASE
Image 6-3 Zoom/Focus adjustment
2. Use the or key to zoom and or key to fo
cus the image.
3. When nished, press EXIT key to return or ENTER to continue to the shift adjustment.
Press the LENS key to call the list with available test patterns.
Quick shift adjustment
1. Press the LENS key on the remote control or local keypad to open the Z oom /Focus Adjustment menu.
66
R5905032 HDX SERIES 02/03/2015
Page 71
Image 6-4 Zoom/Focus adjustment
2. Press ENTER to go to the Shift menu.
6. Quick set up adjustment
Image 6-5 Shift adjustment
3. Use the or key to shift the lens in vertical direction. Use the or key to shift the lens in horizontal direction. Press ENTER to switch to zoom/focus adjustment.
6.3 Direct Lens Adjustment (RCU)
Lens adjustment buttons on the Remot
On the Remote Control four buttons with double action are provided, allowing direct alignment for lens ZOOM, FOCUS, HORIZON­TALSHIFTandVERTICALSHIFT.
1. Press LENS ZOOM button [-] or [+] (A) for correct image size on the screen.
e Control
R5905032 HDX SERIES 02/03/2015
67
Page 72
6. Quick set up adjustment
2
1
CONTR
LENS
SHIFT
LENS SHIFT
B
D
Image 6-6 Direct lens adjustment keys
AZoom B Vertical shift CFocus D Horizontal shift
A
C
LENS
ZOOM
LENS
FOCUS
2. Press LENS FOCUS button [-] or [+] (C) for an overall focus of the image.
3. Press LENS SHIFT button for correct vertical position of the image on the screen.
4. Press LENS SHIFT button for correct horizontal position of the image on the screen.
6.4 Quick picture in picture
Quick On - Off
Press on the PIP key on the remote control or the local keypad to activate the Load layout window.
Use the ▲▼key to scroll to the desired layout and press ENTER to activate.
Select Main full screen to switch off PIP.
Image 6-7 Load layout le list
6.5 Quick language selection
Quick language selection via the remote control
When no OSD menu is visible on the screen, press the Info button (1) on the remote control.
68
R5905032 HDX SERIES 02/03/2015
Page 73
6. Quick set up adjustment
1
5
%
*
5
$
3
1
(
7
7
3
,
3
:
2
'
1
,
:
MENU
Image 6-8 Info button
The language selection menu is displayed on the screen.
Select the desired language with the ▲▼key and press ENTER to activate. The current active language is indicated with a selected radio button
EXIT
ENTER
Image 6-9 Change language
Language selection via OSD
1. Press Menu to activate the menus and select Projector Control Change Language.
2. Press ENTER to open the language selection menu.
3. Select the desired language with the ▲▼key and press ENTER to activate.
The current active language is indicated with a selected radio button
R5905032 HDX SERIES 02/03/2015 69
Page 74
6. Quick set up adjustment
Image 6-10 Main menu
Image 6-11 Projector Control
Image 6-12 Change language
70 R5905032 HDX SERIES 02/03/2015
Page 75
7. Start up of the adjustment mode
7. START UP OF THE ADJUSTMENT MODE
Overview
About the adjustment mode
About the use of the remote control and the local keypad
Start up the adjustment mode
Navigation and adjustments
Menu memory
Shortcut keys to the menus
Test patterns in adjustment mode
Help information in adjustment mode
7.1 About the adjustment mode
Overview
As the adjustment mode is the central place to control and align the projector, the following functions can be done:
Input setup: different Input settings can be adjusted such as specic input slot settings, locking, native resolution and no signal
settings.
Image adjustment: these adjustments are organized per image source and contain the aspect ratio, timings and image settings.
Layout adjustment: set up of the main window and the picture in picture window.
Lamp: manage the lamp mode, the lamp use, lamp type and history
Alignment: groups all controls necessary during the setup of the projector onto a screen.
Projector control: contains the accessibility settings of the projector, such as address and communication setup.
Service: contains information about how the projector is performing. This information will be useful when calling for a service
intervention.
7.2 About the use of the remote control and the local keypad
Overview
All navigations and adjustments can be done either with the remote control or with the local keypad.
Almost all the keys on the remote control have an equivalent on the local keypad.
Exceptions:
Direct adjustment keys such as Contrast, Brightness, Saturation, Phase, etc.
7.3 Start up the adjustment mode
Start up tools
To start up the adjustment mode, use the remote control or the local keypad.
How to start up?
1. Press Menu on the remote control (RCU) or on the local keypad to start up the Adjustment mode.
R5905032 HDX SERIES 02/03/2015
71
Page 76
7. Start up of the adjustment mode
The main menu of the adjustment mode opens.
Image 7-1 Main me nu
7.4 Navigation and adjustments
How to navigate in the menu structure?
Once in the menu structure, use the or key on the remote control or on the local keypad to scroll through the items in the displayed menu. The selected item will get a background color. To activate a selected submenu or function, press ENTER.
When on a submenu, to return one step to the parent menu, press EXIT.
To escape the menu structure when on a menu, press MENU.
How to make an adjustment?
With the remote control or the local keypad navigate through the menu structure until the desired item is selected. Press the orkey until the desired item is reached. Press EXIT to nalize the adjustment.
With the local keypad or remote control, press the or key until the desired value (setup) is reached. Press EXIT to nalize the adjustment.
Direct adjustment within the menu:
Image 7-2
Use the or key to directly adjust the current value.
or,
Via bar scale adjustment :
Once an item is selected, press ENTER to open the bar scale menu.
Image 7-3 Contrast adjus tment
72 R5905032 HDX SERIES 02/03/2015
Page 77
7. Start up of the adjustment mode
Use the or key to adjust the current value.
The bar scale will move accordingly.
Press EXIT to nalize the adjustment.
or,
When the bar scale is displayed, via direct input. Press ENTER to activate the input eld.
Image 7-4 Direct contrast adjustment
Enter the desired value with the digit keys. Press ENTER to accept.
Press EXIT to nalize the adjustment.
7.5 Menu memory
Overview
Each menu with sub menus, remembers its last selected sub item even when leaving the menu structure and that as long as the projector is running. When restarting the projector from stand-by, the menu memory is reset.
After re-opening the main menu and selecting an item, the previous selected be opened just by pressing ENTER.
sub item of that selected item is highlighted and can
7.6 Shortcut keys to the menus
About a shortcut key
The digit keys 5 to 9 can be customer programmed to directly open a pre-stored menu. That menu can be any independent menu out of the list of menus. A menu which is built up by the content of a previous menu cannot be stored behind a shortcut.
How to use a shortcut key
While in the operational mode, no menu selected, just press on the desired digit key to open the menu behind that shortcut key.
How to create a shortcut key
Scroll to the desired menu. Press the digit key behind which the menu must be stored for 5 seconds. When the creation is success­fully, a conrmation message appears on the screen. E.g. :
Image 7-5
Select Yes to conrm the creation.
To erase the shortcut, navigate to Proje
ctor Control Buttons.
R5905032 HDX SERIES 02/03/2015 73
Page 78
7. Start up of the adjustment mode
7.7 Test patterns in adjustment mode
Overview
When the adjustment mode is started, a test pattern can be called at any moment just by pressing the Pattern key on the RCU or the local key path. Press as many times on the Pattern key as necessary to display the desired test pattern. The test pattern remains on the screen as long as the adjustment mode is selected, even when selecting other menus. When leaving the adjustment mode, the selected test pattern is cleared and the normal image is displayed again.
1
6
RGB
PATTERN
STBY
Image 7-6 Pattern button
3
2
89
7
WINDOW
PAUSE TEXT
1
4
PIP
AUTO
5
0
LENS
FN
MENU
EXIT
ENTER
1
5
*
5
MENU
%
$
3
1
(
7
7
3
,
3
2
'
1
,
:
EXIT
ENTER
:
7.8 Help information in adjustment mode
Overview
For many items in the adjustment mode, help information is available. When on an item, just click on the info button of your remote control to display information about the selected item.
1
5
%
*
5
Image 7-7 Info button
When no information is available for the selected item, the message No help available for this item is displayed.
To return to the adjustment mode, press EXIT.
74
$
MENU
3
1
(
7
7
3
,
3
2
'
1
,
:
EXIT
ENTER
:
R5905032 HDX SERIES 02/03/2015
Page 79
8. INPUT
Overview
Input menu overview
Input Selection
Advanced Settings
Input locking
Minimum delay
Native resolution
No Signal
•EDID
3D input
In all cases, the minimum input frequency for 3D is 23 Hz per eye. Below this frequency the image will not be displayed correctly.
8.1 Input menu overview
8. Input
Overview table
Level 1 Level 2 Level 3 Level 4
Input
Input Selection DVI/RGB
SDI (SD/HD/3G/Dual)
Optional input 1
Optional input 2
Advanced Settings DVI/RGB
SDI (SD/HD/3G/Dual)
Input Locking Input on Main Window
Input on Pip Window
Input 1
Input 2
Input 3
Input 4
Free Run
Free Run Options
Minimum delay
Native Resolution [On/Off]
No Signal Color [black/blue]
DVI
DVI Dual link
RGB HS-VS
YUV HS-VS
AUTO
Input 1 Priority
Input 2 Priority
Input 1
Input 2
DUAL SDI
R5905032 HDX SERIES 02/03/2015
75
Page 80
8. Input
EDID
3D
Logo [On/Off]
Shutdown [Off/On]
Shutdown time
Auto dimming [On/Off]
Congure
Create
Delete
Delete All
Status
Auto Detection
Input type
Second input
Frame sequential - Single channel Frame sequential - Dual channel Frame packing (FHD3D)
Side-by-side
Top-and-bottom
SENSIO®HI-FI 3D
Line Alternating (3G)
8.2 Input Selection
How to select
1. Press Menu to activate the menus and select Input Input Selection.
2. Press ENTER.
The Select Source menu is displayed with the actual available sources lled out.
3. Use the or key to select an input.
Image 8-1 Main window
Image 8-2 Input selection
76 R5905032 HDX SERIES 02/03/2015
Page 81
Image 8-3 Select source
8.3 Advanced Settings
Overview
About Input Setup
Input conguration
DVI - RGB input
SDI input
5 cable input
HDMI - DisplayPort input (3D input module)
8. Input
8.3.1 About Input Setup
Overview
Each input module must be congured before these module can be used. This conguration is necessary so that the projector knows which type of signal is connected to its input.
The projector has 4 input slots. Slot 1 and 2 is lled up by default with a DVI and Dual SDI input. Slot 3 and 4 can be lled up with optional input modules. Identical modules are allowed.
8.3.2 Input conguration
3D item in the Input menu is grayed out when no 3D module is inserted in slot 3 or 4.
How to change?
1. Press Menu to activate the menus and select Input Adv anced Settings.
2. Press ENTER.
The Advanced Settings window is displayed with the actual situation lled out.
3. Use the or key to select an input Press ENTER to open the selection menu which will be different from input type to input type.
Image 8-4 Main window
R5905032 HDX SERIES 02/03/2015 77
Image 8-5 Advanced input settings
Page 82
8. Input
Image 8-6 Advanced settings, input selection
8.3.3 DVI - RGB input
How to select
Select DVI / RGB and press ENTER to open the selections
Image 8-7 DVI selection
The following selections are possible:
•DVI
DVI - dual link
RGB HS-VS/CS
YUV HS-VS/CS
•AUTO
DVI will not natively support 10-bit or 12-bit deep color. It is possible to enable 30-bit color over DVI using a specic pixel packing. We support the pixel-packing that is implemented by Silicon Image Sil7189 DVI re­ceiver.
About AUTO selection
When AUTO is selected, the input source is automatically detected (only for DVI, RGB or YUV). When an analog source is detected in AUTO mode, then the Color Space must be selected as no automatic detection is possible.
Use the or key to select the correct color space and press ENTER to select.
Image 8-8 Color space selection for AUTO
78 R5905032 HDX SERIES 02/03/2015
Page 83
8.3.4 SDI input
About SDI input
The Dual SD/HD/3G-SDI Input can accept standard-denition (SD), high-denition (HD) and 3 Gigabit-denition serial-digital-inter­face (SDI) signals .
How to select
Select SDI (SD / HD / 3G / Dual) and press ENTER to open the selections
Image 8-9 SDI, input type selection
The following selections are possible:
Input 1 Priority (when 2 sources are present, the source on input 1 will have the priority)
Input 2 Priority (when 2 sources are present, the source on input 2 will ha
Input 1
Input 2
Dual SDI
ve the priority)
8. Input
SDI setup
To set up the SDI input, select Setup and press ENTER.
Image 8-10 SDI set up
First, select the standard. Use the or key to select and press ENTER to accept.
Standard :
4:2:2 - YCbCr-10
4:4:4 - YCbCr-10
•4:4:4-RGB-10
4:2:2 - YCbCr-12
4:4:4 - YCbCr-12
•4:4:4-RGB-12
Then, select the 3G setting. Use the or key to select and press ENTER to accept.
R5905032 HDX SERIES 02/03/2015
79
Page 84
8. Input
3G-A and 3G-B:
Direct Mapping (3G-A)
Dual HD (3G-B)
When Dual HD is selected, it is possible to use Swap links. If Swap links must be used, use the or key to select and press ENTER to accept. The check box will be checked.
Dual HD :
Swap links
8.3.5 5 cable input
How to select
Select 5 cable and press ENTER to open the selections
Image 8-11 Advanced settings, 5-cable
Image 8-12 5 cable conguration
Use the or key to select the desired conguration and press ENTER to select.
When e.g. CVBS/S-VIDEO AUTO is selected, the projector discovers itself which type of signal is connected to it and loads the correct settings.
For RGB selections, advanced settings are possible. To adjust these advanced settings, use the or key to select Advanced settings and press ENTER. The advanced settings menu opens:
Press ENTER to toggle between [Analog] and [TTL].
8.3.6 HDMI - DisplayPort input (3D input module)
How to select
Select HDMI/DP and press ENTER to open the selections
Image 8-13 HDMI-Display port selection
Use the or key to select the desired input and press ENTER to select.
80
R5905032 HDX SERIES 02/03/2015
Page 85
8.4 Input locking
What is possible?
The output signal can be locked on an internal sync signal or on the sync signal of one of the input sources. Or it can follow the input of the Main window or Pip window. When locked to the corresponding input sync, the output will be shown without movement artifacts. With locking to a specic input, a set of projectors can be kept in sync, no matter what input image is shown.
Input locking is grayed out when 3D is active. Input locking is set automatically to the 3D source.
How to set up
1. Press Menu to activate the menus and select Input Input locking.
2. Press ENTER.
The Input locking window is displayed with the current selection.
3. Use the or key to select a input to lock on.
8. Input
Image 8-14 Main window
Image 8-16 Input locking
Image 8-15 Input
Input on Main window Output is locked on the selected source of the main window
Input on PIP window Output is locked on the selected source of the Pip window
Input 1
Input 2
Input 3
Input 4
Output is locked on input 1
Output is locked on input 2
Output is locked on input 3
Output is locked on input 4
Free run Output is locked on an internal sync (60 Hz or manual setup)
R5905032 HDX SERIES 02/03/2015
81
Page 86
8. Input
When Input locking is set to a specic input and there is no sync signal available, the locking will be switched to Free run without changing the user settings. Once the sync is available, it applies again the user settings.
Options for Free Run
When free run is selected, radio button selected, then the Free Run Options become available.
Image 8-17 Free run options
Use the or key to select Fixed 60 Hz or Manual and press ENTER to select.
Fixed60Hz:
Manual
To change the locking frequency for Manual, use the or key to select Vert freq and press ENTER to activate.
Image 8-18 Free run, manual setting
Use the or key to change the value.
locking is done on an internal sync of 60 Hz
locking is done on the indicated vertical frequency which can be changed by the user (between 24 Hz and 60 Hz).
8.5 Minimum delay
Purpose
The minimum delay only affects the de-interlacing. In case of interlaced sources, the de-interlacer will be bypassed and the image will be shown with line interpolation applied.
To ensure minimum delay in the other processing steps, make sure warping is OFF, the resolution of the input source is native and the input locking is set to the main input.
How to toggle the delay
1. Press Menu to activate the menus and select Input Minimum delay [On].
82
R5905032 HDX SERIES 02/03/2015
Page 87
Image 8-19 Main window
2. Press ENTER to toggle between [On] and [Off].
[On] : images displayed with minimum delay
[Off] : images displayed without minimum delay
8.6 Native resolution
Image 8-20 Input, minimum delay
8. Input
What can be done
The aim here is to always show the resolution of the source independently of the resolution of the DMD panels.
When the resolution of the source is exactly the resolution of the DMD panels, then the full content will be shown on the full DMD (A).
When the resolution of the source is higher than the resolution of the DMD panels, then only part of the image will be shown (B)
When the resolution of the source is lower than the resolution of the DMD panels, then the full image will be shown but only on part of the DMD is used.
Image 8-21
When the show native resolution function is in the ON position, the projector handles the source as follows:
Source Projected image
Name Ratio Resolution Ratio Resolution
XGA 4:3 1024x768 4:3 1024x768 image projected with black
borders
SXGA 5:4 1280x1024 5:4 1280x1024 image projected with black
borders
SXGA+ 4:3 1400x1050 4:3 1400x1050 image projected with black
borders
R5905032 HDX SERIES 02/03/2015 83
Page 88
8. Input
Source
UXGA
WUXGA
4:3 1600x1200 4:3 1600x1200 image projected with black
16:10 1920x1200 16:10 1920x1200 normal image projected
Projected image
How to toggle to native resolution?
1. Press Menu to activate the menus and select Input Native Resolution [On].
2. Press ENTER to toggle between [On] and [Off].
[On] : images displayed in native resolution
[Off] : images scaled to ll the complete screen
Image 8-22 Main window
Image 8-23 Input, native resolution
borders left and right.
8.7 No Signal
Overview
Background color
Background Logo
Shutdown settings
Shutdown retarding time
Auto Dimming
Whatcanhappenwhennosignal
When no signal is available at the selected input, the output can be set to blue or black or a personal dened logo can be displayed or the projector can shutdown after a certain time or auto dimming can be started.
8.7.1 Background color
How to set the background color
1. Press Menu to activate the menus and select Input No Signal. Color.
2. Press ENTER to toggle between [Blue] or [black].
84
R5905032 HDX SERIES 02/03/2015
Page 89
Image 8-24 Main window
Image 8-25 Input, no signal
8. Input
Image 8-26 No signal, color
8.7.2 Background Logo
What can be done ?
A logo can be switched on or off.
When logo is switched on and a logo is available, that logo will be displayed when no signal is available for the main window an no signal available for the PiP window in case PiP is On.
How to activate logo
1. Press Menu to activate the menus and select Input No Signal. Logo.
2. Press ENTER to toggle between [On] or [Off].
Image 8-27 Main window
Image 8-28 Input, no signal
R5905032 HDX SERIES 02/03/2015 85
Page 90
8. Input
Image 8-29 No signal, logo
A dedicated logo can be loaded via Projector Toolset with a HDX plug-in installed.
8.7.3 Shutdown settings
How to change the settings
1. Press Menu to activate the menus and select Input No Signal. Shutdown.
Image 8-30 Main window
Image 8-32 No signal, shutdown
Image 8-31 Input, no signal
2. Press ENTER to toggle between [On] and [Off].
[On] : projector goes in shutdown after a certain retarding time.
[Off] : projector does not go in shutdown.
8.7.4 Shutdown retarding time
About the shutdown retarding time
The retarding time is the time between no signal is detected and the moment that the projector shuts down.
How to set the retarding time
1. Press Menu to activate the menus and select Input No Signal. Shutdown time (min).
86
R5905032 HDX SERIES 02/03/2015
Page 91
Image 8-33 Main window
Image 8-34 Input, no signal
8. Input
Image 8-35
2. Press ENTER to toggle between [1], [3], [5] and [10] minutes.
8.7.5 Auto Dimming
About auto dimming
When no signal is detected on the selected input the lamp power will be reduced from the current value to its minimum value. When the input signal is re-detected, the lamp power is restored to its original value.
How to set up
1. Press Menu to activate the menus and select Input No Signal. Auto Dimming.
Image 8-36 Main window
Image 8-37 Input, no signal
R5905032 HDX SERIES 02/03/2015 87
Page 92
8. Input
Image 8-38 No signal, auto dimming
2. Press ENTER to toggle between [On] or [Off].
[On] : when no signal, auto dimming is started.
[Off] : when no signal, no auto dimming is started.
8.8 EDID
EDID
Extended Display Identication Data
About EDID
The EDID le available for DVI input connectors includes timings supported by the projector; display size and other information about the display (i.e. projector). It is the set of information that is used by digital sources connected to the projector to generate a suitable image signal.
From the OSD, you can for each DVI input connector choose to use the Standard EDID le or create and force your custom made EDID le. The selection of the EDID le to be used is made in the Congur e menu. Making your own custom EDID le(s) is done through Create.CustomEDIDfiles can be deleted at any time.
The Standard EDID includes two timings: 1920x1200@60Hz / 1920x1080@60Hz (for HDX, HDF and APOLLO projectors) and 2048x1080@60Hz / 1920x1080@60Hz (for HDQ projectors).
Overview
•Configure an input
Create custom EDID le
Delete a custom EDID le
Delete all custom EDID le
8.8.1 Congure an input
Description
Selecting the Standard EDID le or an own created le can be selected from the list of Custom EDID les for the input.
How to congure
1. Press Menu to activate the menus and select Input EDID Congure.
2. Press ENTER to open the EDID conguration menu.
88
R5905032 HDX SERIES 02/03/2015
Page 93
Image 8-39 Main window
Image 8-40 Input, EDID
8. Input
Image 8-41 EDID, congure
Image 8-43 EDID se lection list
Image 8-42 EDID conguration
3. Use the or key to select the input to congure. Press ENTER to open the selection list.
The current active le is checked.
4. Use the or key to select the correct le. Press ENTER to select this le. Press EXIT to return to the EDID Conguration menu.
5. Use the or key to select Apply.
Your selection is applied and stored for this input.
The EDID Conguration menu remains open to congure another input. Or, use the or key to select OK.
Your selection is applied and stored for this input and the EDID conguration menu is closed.
R5905032 HDX SERIES 02/03/2015
89
Page 94
8. Input
8.8.2 Create custom EDID le
Description
You can create new custom EDID les and enter the desired input timings.
How to create
1. Press Menu to activate the menus and select Input EDID Create.
2. Press ENTER to open the EDID creation menu.
Image 8-44 Main window
Image 8-45 Input, EDID
Image 8-46 EDID, create
Image 8-47 EDID le creation
3. Use the or key to select Create. Press ENTER to open the creation menu.
4. Fill out the Timings section. Use the or key to select a setting. Use the or key to change the value or press ENTER to open the specic adjustment menu. Follow the adjustment method as described in "Navigation and adjust­ments", page 72. The following timings must be entered:
- Active Pixels: horizontal resolution
- Active Lines: vertical resolution
- Frequency (Hz): amount of frames per second
5. Select the calculation method to obtain the correct (standard) video timings. Possible selections:
- CVT: Coordinated Video Timings
- CVT RB: Coordinated Video Timings Reduced Blanking
- CVT MB: Coordinated Video Timings Minimum Blanking (not a standard)
- GTF: Generalized Timing Formula
90
R5905032 HDX SERIES 02/03/2015
Page 95
8. Input
6. Select the Options. If necessary, scroll down to see extra options. Select or clear the check boxes.
Image 8-48 EDID le creation, options
The following options are possible:
- Stereo: this check box is currently not in use. You can leave it unchecked.
- Deep color: select this box in case of a 12 bit color signal. In this case, the Single Link pins of the DVI connector convey the
eight most signicant bits, while the Dual Link pins convey the four least signicant bits.
- Analog: this check box makes the selection between DVI digital or DVI analog. When checked, DVI analog is active.
7. A lename is proposed. This proposed name contains the resolution, ca To change the le name, select Filename and press ENTER to open the edit box. Click inside the edit box and change the name to the desired name.
8. Select Create and press ENTER to create the new custom le.
lculation, frequency and a D or A for digital or analog.
8.8.3 Delete a custom EDID le
Standard EDID les cannot be deleted.
How to delete
1. Press Menu to activate the menus and select Input EDID D
2. Press ENTER to open the EDID list with custom les.
Image 8-49 Main window
Image 8-50 Input, EDID
elete.
R5905032 HDX SERIES 02/03/2015 91
Page 96
8. Input
Image 8-51 EDID, delete
3. Use the or key to select the le which must be deleted. Press ENTER to delete.
Image 8-53 Conrmation
Image 8-52 EDID, delete list
Aconfirmation window opens.
4. Select Ye s to delete the le and press ENTER.
8.8.4 Delete all custom EDID le
Standard EDID les cannot be deleted.
How to delete
1. Press Menu to activate the menus and select Input EDID Delete All.
2. Press ENTER to open the conrmation window.
92
R5905032 HDX SERIES 02/03/2015
Page 97
Image 8-54 Main window
Image 8-56
3. Select Ye s to delete all the custom le and press ENTER.
Image 8-55 Input, EDID
Image 8-57
8. Input
8.9 3D input
Overview
About 3D modes
•Activate3D
Auto detection
Input type selection
3D second input
L-R Synchronisation, eld dominance
L-R Synchronisation, Invert 3D sync out
8.9.1 About 3D modes
The mentioned menu items in the mode explanation will be explained in detail in the next topics.
Settings in the 3D menu are stored per input.
Single 3D channel - Full resolution - sequentia
Content is displayed by one 3D source. The frames for the left eye and right eye are displayed alternately (sequential mode). Optional an external 3D sync can be used. The external 3D sync has to be applied to the “3D SYNC IN” port (BNC socket at the left) of the 3D Input Module.
If two 3D Input Modules are used:
In case a 3D Input Module is selected: use the SYNC IN of this 3D Input Module.
In case another (DVI, SDI, 5-cable, …) input module is selected: use the SYNC IN of the rst (lowest input number) 3D Input
Module.
If the external 3D sync is not available an internal 3D sync is generated by the projector. With the setting “Field dominance”the Sync In signal can be inverted to match the left and right eye elds.
MENU > Input > 3D > L/R Synchronisation > Field Dominance [L/R] or [R/L]
Example: A DisplayPort source with a frequency of 120 Hz consisting of content for the left and right eye results in a 60 Hz video per eye.
l mode
R5905032 HDX SERIES 02/03/2015
93
Page 98
8. Input
To activate the single channel 3D mode select:
MENU > Input > 3D > Frame S equential – Single Channel
Possible sources: DisplayPort, HDMI, dual-link DVI, 5-cable analog (up to 210 MHz), DVI analog (up to 170 MHz), SDI (up to 150 MHz).
With the “Invert 3D sync out” setting the content can be switched between the left and right eye of the user.
The “Field dominance” setting has only effect in the 3D mode: Frame sequential Single channel (in all other modes this setting is grayed out). Furthermore, the input frequency must be equal or lower than 100 Hz (50 Hz per eye). In case the input frequency is higher than 100 Hz (50 Hz per eye, 59.94 & 60 Hz in practice), the “Field dominance” setting has no effect.
Single 3D channel - Full resolution - other formats
Contains Frame packing and Line Alternating (3G-B).
To activate the single channel 3D mode select:
MENU > Input > 3D > Frame packing (FHD3 D)
or
MENU > Input > 3D > Line Alternating (3G -B) (only for SDI input)
Single 3D channel - Half resolution
3D content is distributed by one 3D source by means of “Side By Side”, “Top Bottom” or “SENSIO®Hi-Fi 3D”..
To activate this single channel 3D mode select one of the three options:
MENU > Input > 3D > Side-By-Side (Half)
MENU > Input > 3D > Top-and-Bottom (Half)
®
MENU > Input > 3D > SENSIO
Example: A 3D HDMI source with a Side by Side video of 60 Hz results in a 60 Hz video per eye.
In this mode the 3D Input Module also generates the 3D sync.
Possible sources: Display Port, HDMI, DVI , SDI input.
3D Decoder - FFC (only on 3D input)
Dual 3D channel - Two parallel 3D content streams
3D content is applied to the projector via two input ports. One port is used for content of the left eye, the other port for the right eye.
Example: Two parallel DVI streams of 60 Hz: DVI cable 1 is connected wi
th the DVI port of the projector. DVI cable 2 is connected
via a HDMI converter cable with the HDMI port of the 3D Input Module. To switch the HDMI/DP input to HDMI, select
MENU > Input > Advanced Settings > HDM I/DP > HDMI.
For the second source the correct type has to be selected as follows with the rst source already selected :
MENU > Input > 3D > Second Input > “select corresponding slot number”
The 3D Input Module is activated for Dual 3D channel:
MENU > Input > 3D > Frame Sequential – Dual c hannel
Possible sources: 2 x DVI , 2 x SDI. If two 3D Input Modules are installed: 2 x HDMI or 2 x DisplayPort.
SENSIO®Hi-Fi 3D
(2)
1
3
2
(1)
1
3
2
4
2
4
1
3
1
3
2
4
2
4
1
3
1
1
1
4
3
2
4
2
4
3
2
4
3
(4)
(5)
(6)
1234
1234
1234
1234
1234
1234
1234
1234
(7)(3)
Image 8-58
®
HI-FI 3D decoding
SENSIO
94 R5905032 HDX SERIES 02/03/2015
Page 99
8. Input
1
SENSIO
2
Left expansion
®
Hi-Fi 3D stream
3 Right expansion
4
5
SENSIO
SENSIO
®
Hi-Fi 3D interpolation
®
Hi-Fi 3D interpolation
6 Right stream
7
Left stream
®
SENSIO enables an automatic detection of 2D, Top-and-Bottom, Side-by-Side and the SENSIO fast detection time between these formats. Only progressive formats are supported. Interlaced formats will be displayed in 2D (one eye only). The SENSIO
3D Decoder - FFC is using both the SENSIO®3D Decoder as well as the SENSIO®Autodetect functionality. This mode
®
Autodetect feature requires a minimum of 1120x540 active pixels per eld/frame to operate.
®
Hi-Fi 3D format, with a clean transition and
The acronym FFC stands for ‘Full Frame Compatible’, in other words, the decoder handles all full frame based 3D formats.
Double or triple ash
Double or triple ash is used for 3D sources to avoid ickering images.
Input frequency < 40Hz/eye triple ash will be used and results in:
144Hz for 24Hz/eye input
150Hz for 25Hz/eye input
180Hz for 30Hz/eye input
Input frequency between 40Hz and 51Hz/eye double ash will be used and results in:
192Hz for 48Hz/eye input
200Hz for 50Hz/eye input
Supported formats
Frame sequential
Single channel
Frame Packing (FHD3D)
Side-by-Side
Top-and-Bottom
DVI/HDMI/DP
5–cable analog DVI analog
SDI
Fpix 210 MHz Fpix 210 MHz Fpix 170 MHz Fpix 150 MHz
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
1400x1050@120Hz or 1600x900@120Hz.
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
1400x1050@120Hz or 1600x900@120Hz.
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
1280x720@120Hz or 1280x800@120Hz.
Max. resolution:
1920x1200@60Hz, 2048x1080@60Hz or 1280x720@120Hz.
Interlaced/progressive Interlaced/progressive Interlaced/progressive Interlaced/progressive
HD formats only.
Max. resolution:
1920x1080@30Hz or 1280x720@60Hz.
HD formats only.
Max. resolution:
1920x1080@30Hz or 1280x720@60Hz.
HD formats only.
Max. resolution:
1920x1080@30Hz or 1280x720@60Hz.
HD formats only.
Max. resolution:
1920x1080@30Hz or 1280x720@60Hz.
Progressive only Progressive only Progressive only Progressive only
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
Interlaced/progressive Interlaced/progressive Interlaced/progressive Interlaced/progressive
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
Progressive only Progressive only Progressive only Progressive only
R5905032 HDX SERIES 02/03/2015 95
Page 100
8. Input
2xDVI/2xHDMI/2xDP
Frame Sequential
Dual Channel
Fpix 210MHz. Fpix 150MHz.
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
Progressive only Progressive only
SDI (3G - Level B)
Line Alternating (3G-B)
Fpix 150MHz.
Max. resolution
1920x1200@30Hz, 2048x1080@30Hz or 1280x720@60Hz.
HDMI/DP
SENSIO®3D Decoder - FFC
Fpix 162MHz & Vfreq 60Hz.
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
Progressive only
Other settings to use the 3D glasses
Adjust the following setting:
•Darktime
L/R output reference delay
3D Sync Loop Through
These settings can be found as follows:
MENU > Alignment > 3D Glasses
1
2xSDI
2
Max. resolution:
1920x1200@30Hz, 2048x1080@30Hz or 1280x720@60Hz.
3
8.9.2 Activate 3D
What can be done ?
The status of the 3D function can be enabled or disabled.
This function is input dependent.
How to enable/disable
1. Press Menu to activate the menus and select Input 3D Status.
Image 8-59 Main window
Image 8-60 Input, 3D
1. 2x HDMI and 2x DP requires 2 3D input modules. 2xDVI can be done with a DVI input and a 3D input with DVI to HDMI convertor
2. For 2xSDI, IN1 and IN2 of the SDI input can be used. The input settings under MENU -> Input -> Advanced Settings -> SDI/HDSDI/3G must be set to ‘DUAL SDI’
3. For SDI (3G- Level B), IN1 or IN2 of the SDI input can be used. The input settings under MENU -> Input -> Advanced Settings -> SDI/HDSDI/3G must be set to ‘Input 1’ or ‘Input 2’, with or without Priority
96 R5905032 HDX SERIES 02/03/2015
Loading...