How it Works
Barco
Loading...
CLM HD8 R59770057
User Manual
231 pgs14.07 Mb0

Barco CLM HD8 R90501301, CLM HD8 R59770057 User Manual

CLM HD8
R59770057/08 15/03/2010
User guide
R9050130 R90501301 R90501305
Barco nv Events Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.88.24 E-mail: sales.events@barco.com Visit us at the web: www.barco.com
Printed in Belgium
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war­ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not other stored in a retrieval system without the prior written consent of Barco.
wise be recorded, transmitted or
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufacturers.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference at his own expense
EN55022/CISPR22 Class A ITE (Information Technology Equipment)
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such equipment should not be restricted in its sale but the following warning shall be included in the instructions for use:
Warning : This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be complied with by the customer.
Software License Agreement
You should carefully read the following terms and conditions before using this software. Your use of this software indicates your acceptance of this license agreement and warranty.
Terms and Conditions:
1. No redistribution of the software is allowed.
2. Reverse-Engineering. You may
Disclaimer of Warranty:
not reverse engineer, decompile, disassemble or alter anyhow this software product.
This software and the accompanying files are sold “as is” and without warranties as to performance or merchantability or any other war­ranties whether expressed or implied. In no event shall Barco be liable for damage of any kind, loss of data, loss of profits, business interruption or other pecuniary loss arising directly or indirectly. Any liability of the seller will be exclusively limited to replacement of the product or refund of purchase price.
GNU-GPL code
If you would like a copy of the GPL source code contained in this product shipped to you on CD, please contact Barco. The cost of preparing and mailing a CD will be charged.
Disposal Information
This equipment has required the extraction and use of natural resources for its production. It may contain hazardous substances for health and environment. In order to avoid the dissemination of those substances in the environment and to diminish the pressure on natural resources, we encourage you to use the appropriate take-back systems. Those systems will reuse or recycle most of the materials of your end of life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use those systems. If you need more information on the collection, reuse and recycling systems, please contact your local or regional waste administrator. You can also contact us for more information on the environmental performances of our products.
Table of contents
TABLE OF CONTENTS
1. Safety................................................................................................................. 5
1.1 General ............................................................................................................................... 5
1.2 Important safety instructions ......................................................................................................... 6
1.3 Recycling guidelines.................................................................................................................. 8
1.4 Important warnings concerning CLM flight cases ................................................................................... 9
2. General.............................................................................................................. 11
2.1 Installation requirements .. .......................................................................................................... 11
2.2 Unpacking the projector ............................................................................................................. 12
2.3 Box content..........................................................................................................................13
2.4 Projector configurations.............................................................................................................14
2.5 Projector air inlets andoutlets.......................................................................................................17
2.6 Free downloadof ProjectorToolset.................................................................................................17
3. Physical installation ..............................................................................................19
3.1 Remote control unit (RCU) . .........................................................................................................19
3.1.1 RCU battery installation.......................................................................................................20
3.1.2 RCU rugged case installation ................................................................................................21
3.1.3 RCU XLR adaptor installation ................................................................................................21
3.1.4 Using the XLR adaptor of the RCU. . . ........................................................................................ 22
3.1.5 RCU usage possibilities ......................................................................................................22
3.2 Lenses ...............................................................................................................................23
3.2.1 Available lenses............................................................................................................... 23
3.2.2 Lens selection .................................................................................................................23
3.2.3 Lens formulas .................................................................................................................24
3.3 Alignment of a table mounted CLM projector.......................................................................................24
3.4 Suspension of the CLM projector with rigging clamps . . ........................................................................... 25
3.5 Alignment of a ceiling mounted CLM projector . . ................................................................................... 29
4. Stacking CLM projectors.........................................................................................31
4.1 Stacking CLM projectors ............................................................................................................ 31
4.2 Aligning stacked CLM projectors....................................................................................................33
5. Connections........................................................................................................35
5.1 Power connection . .................................................................................................................. 35
5.2 Input source connections. . ..........................................................................................................37
5.3 Communication connections ........................................................................................................39
6. Getting started .....................................................................................................43
6.1 RCU & Local keypad ................................................................................................................43
6.2 Terminology overview ...............................................................................................................43
6.3 Operating the projector.............................................................................................................. 45
6.3.1 Switching on................................................................................................................... 45
6.3.2 Errors, warnings and messages during start up .. ........................................................................... 46
6.3.3 Switching to standby . .........................................................................................................46
6.3.4 Switching off................................................................................................................... 47
6.4 Using theRCU....................................................................................................................... 47
6.5 Quick setup adjustments ............................................................................................................48
6.5.1 Text boxes ON or OFF........................................................................................................48
6.5.2 Quick Lens Adjustment .......................................................................................................48
6.5.2.1 Quick Lens Adjustment via LENS key ................................................................................. 48
6.5.2.2 Direct Lens Adjustment (RCU).........................................................................................49
6.5.3 Quick picture inpicture .......................................................................................................50
6.5.4 Quick layout selection with Rigging key......................................................................................50
6.5.5 Quick language selection . . . ..................................................................................................51
6.6 Use ofthe AUTO button............................................................................................................. 51
6.7 ProjectorAddress....................................................................................................................51
6.7.1 Displaying and Programming addresses. . ................................................................................... 51
6.7.2 Controlling the projector ......................................................................................................52
6.8 Source selection.....................................................................................................................53
6.9 Controlling the Projector.............................................................................................................53
7. Start up of the adjustment mode ...............................................................................55
7.1 About the adjustment mode .........................................................................................................55
7.2 About the use ofthe remotecontroland the local keypad ......................................................................... 55
7.3 Start up the adjustment mode.......................................................................................................55
7.4 Navigation and adjustments.........................................................................................................56
7.5 On screen menus versus LCD display menus . . ...................................................................................56
8. Input menu .........................................................................................................59
8.1 Overview flow........................................................................................................................ 59
8.2 Slot module type..................................................................................................................... 59
8.2.1 About Input Setup .............................................................................................................59
R59770057 CLM HD8 15/03/2010
1
Table of contents
8.2.2 Input configuration ............................................................................................................ 60
8.3 Input locking . ........................................................................................................................61
8.4 Minimum delay.......................................................................................................................63
8.5 Native resolution.....................................................................................................................63
8.6 Source switching ....................................................................................................................65
8.7 No signal .............................................................................................................................65
8.7.1 Backgroundcolor .............................................................................................................66
8.7.2 Shutdownsetting.............................................................................................................. 66
8.7.3 Shutdownretarding time......................................................................................................66
9. Image menu ........................................................................................................69
9.1 Overview flow........................................................................................................................ 69
9.2 How to select the image adjustments? . . . . . ........................................................................................70
9.3 Image Settings.......................................................................................................................70
9.3.1 Contrast .......................................................................................................................71
9.3.2 Brightness.....................................................................................................................71
9.3.3 Saturation ..................................................................................................................... 72
9.3.4 Tint (hue)...................................................................................................................... 73
9.3.5 Phase..........................................................................................................................73
9.3.6 Sharpness .....................................................................................................................74
9.3.7 Noise reduction ...............................................................................................................75
9.3.8 Color temperature.............................................................................................................76
9.3.8.1 Predefined color temperature..........................................................................................76
9.3.8.2 Set a custom color temperature .......................................................................................77
9.3.9 Input balance..................................................................................................................78
9.3.9.1 Introduction to Input Balance . . ........................................................................................ 78
9.3.9.2 Adjusting the input balance ............................................................................................ 79
9.4 Aspect ratio ..........................................................................................................................82
9.5 Timings...............................................................................................................................83
9.5.1 Source timings ................................................................................................................83
9.5.2 Advanced settings ............................................................................................................ 84
9.5.3 Advanced settings, film mode detection ..................................................................................... 86
9.5.4 Advanced setting, brilliant color look.........................................................................................87
9.6 Image files services .................................................................................................................88
9.6.1 Files and file manipulations. ..................................................................................................88
9.6.2 Manual Load file ..............................................................................................................89
9.6.3 Delete file......................................................................................................................89
9.6.4 Delete all custom files ........................................................................................................90
9.6.5 Rename a file .................................................................................................................91
9.6.6 Copy a file.....................................................................................................................92
9.6.7 File options....................................................................................................................92
9.7 Save custom settings................................................................................................................93
10. Layout menu .......................................................................................................95
10.1 Overview flow........................................................................................................................95
10.2 Main window .........................................................................................................................95
10.2.1 Source selection .............................................................................................................. 96
10.2.2 Size adjustment...............................................................................................................96
10.2.3 Position adjustment...........................................................................................................99
10.3 PIP window . ........................................................................................................................100
10.3.1 Introduction to PIP . . .........................................................................................................100
10.3.2 Picturein Picture activation..................................................................................................101
10.3.3 Picturein Picture source selection ..........................................................................................101
10.3.4 Picture in Picture size of the window . .......................................................................................102
10.3.5 Picture in Picture, position window .. ........................................................................................105
10.4 Layout file services.................................................................................................................106
10.4.1 Load layout . .. ................................................................................................................106
10.4.2 Rename a layout .............................................................................................................107
10.4.3 Delete a layout...............................................................................................................107
10.4.4 Copy / Save as a layout .....................................................................................................108
11. Lamp menu........................................................................................................111
11.1 Overview flow.......................................................................................................................111
11.2 Lamp power mode.................................................................................................................. 111
11.3 Lamp power.........................................................................................................................112
11.4 Lamp Identification .................................................................................................................113
11.5 Status and run time overview lamps...............................................................................................114
11.6 Lamp mode .........................................................................................................................114
12. Alignment menu ................................................................................................. 115
12.1 Overview flow.......................................................................................................................115
12.2 Orientation ..........................................................................................................................116
12.3 Lens adjustment ....................................................................................................................117
12.4 Sidekeystone.......................................................................................................................118
12.5 Blanking.............................................................................................................................119
12.6 Intensity.............................................................................................................................120
12.7 Gamma .............................................................................................................................120
2
R59770057 CLM HD8 15/03/2010
Table of contents
12.8 Internalpattern......................................................................................................................121
12.9 Color space.........................................................................................................................122
12.10 White peaking ......................................................................................................................123
12.11 ScenergiX...........................................................................................................................124
12.11.1 Introduction. . .................................................................................................................124
12.11.2 Preparations. . ................................................................................................................125
12.11.3 ScenergiX activation .........................................................................................................125
12.11.4 ScenergiX pattern ............................................................................................................125
12.11.5 ScenergiX overlap zone (horizontal ScenergiX) .. ..........................................................................126
12.11.6 ScenergiX overlap zone (vertical ScenergiX) ...............................................................................128
12.11.7 ScenergiX size adjustment (White level) . . ..................................................................................129
12.11.8 Adjusting the black level of the images . .. ..................................................................................131
13. Projector control ................................................................................................ 135
13.1 Overview flow.......................................................................................................................135
13.2 Projector address . . .................................................................................................................136
13.2.1 Individual projector address .................................................................................................136
13.2.2 Common address ............................................................................................................137
13.3 Serialcommunication...............................................................................................................137
13.3.1 Baud ratesetup .............................................................................................................. 138
13.3.2 Interface standard............................................................................................................138
13.3.3 RS422 termination ........................................................................................................... 139
13.4 Network .............................................................................................................................139
13.4.1 Introduction to a Network connection .......................................................................................140
13.4.2 DHCP setup . . ................................................................................................................140
13.4.3 IP-address set up ............................................................................................................141
13.4.4 Subnet-maskset up..........................................................................................................141
13.4.5 Default Gatewayset up......................................................................................................142
13.5 IRcontrol switching.................................................................................................................143
13.6 DMX.................................................................................................................................144
13.6.1 DMX address. ................................................................................................................144
13.6.2 DMX universe ............................................................................................................... . 145
13.6.3 DMX monitor .................................................................................................................145
13.6.4 DMX mode . . . ................................................................................................................147
13.6.5 Art-NetActivation ............................................................................................................147
13.7 Buttons..............................................................................................................................148
13.7.1 APA button ...................................................................................................................148
13.7.2 Shortcut keys.................................................................................................................148
13.8 Menuposition.......................................................................................................................149
13.9 Local LCD contrast .................................................................................................................150
13.10 Language selection. ................................................................................................................150
14. Service menu..................................................................................................... 153
14.1 Overview flow.......................................................................................................................153
14.2 Identification ........................................................................................................................153
14.3 Diagnosis ...........................................................................................................................155
14.3.1 How to start up the diagnosis? ..............................................................................................155
14.3.2 Versions ......................................................................................................................155
14.3.3 Voltages ......................................................................................................................156
14.3.4 I²C diagnosis . ................................................................................................................157
14.3.5 Temperatures ................................................................................................................157
14.3.6 Fan speeds overview ........................................................................................................158
14.3.7 SPI............................................................................................................................159
14.3.8 Errorlogging overview.......................................................................................................159
14.4 Internalservice patterns............................................................................................................160
14.5 Restore factory defaults ............................................................................................................160
14.6 Savecustom settings...............................................................................................................161
14.7 Refill mode.. . .......................................................................................................................162
14.8 USB memory .......................................................................................................................163
14.9 Over temperature DMD safety .....................................................................................................164
15. Maintenance...................................................................................................... 167
15.1 Cleaning the lens ... ................................................................................................................167
15.2 Cleaning the exterior of the projector ..............................................................................................167
15.3 Level check of cooling liquid .......................................................................................................167
16. Servicing.......................................................................................................... 169
16.1 Replacement of the dust filter onthe top side.....................................................................................169
16.2 Replacement of the dust filters on the front side ..................................................................................170
16.3 Lens installation ....................................................................................................................171
16.4 Lens removal .......................................................................................................................172
16.5 Removal of a lampunit.............................................................................................................173
16.6 Mounting a new lamp unit .. ........................................................................................................175
16.7 Removal of an input module .......................................................................................................176
16.8 Inserting an input module . .........................................................................................................177
16.9 Top-up the reservoir with cooling liquid............................................................................................177
R59770057 CLM HD8 15/03/2010
3
Table of contents
17. Projector covers, removal and installation ................................................................. 181
17.1 Removal of the front cover .........................................................................................................181
17.2 Removal of the lamp door . . ........................................................................................................182
17.3 Removal of the back cover.........................................................................................................183
17.4 Removal of the top cover...........................................................................................................184
17.5 Removal of the side cover..........................................................................................................184
17.6 Installation ofthe sidecover .......................................................................................................185
17.7 Installation ofthe top cover.........................................................................................................186
17.8 Installation ofthe backcover.......................................................................................................186
17.9 Installation ofthe front cover.......................................................................................................187
17.10 Installation of the lamp door........................................................................................................188
A. Dimensions ........................................................................................................ 191
A.1 Dimensions of the CLM HD8.......................................................................................................191
B. Standard Source Files ........................................................................................... 193
B.1 Table overview......................................................................................................................193
C. DMX Chart.......................................................................................................... 195
C.1 CLM control channel mapping (Full mode) ........................................................................................195
C.2 CLM control channel mapping (Basic mode) ......................................................................................196
D. Specifications ..................................................................................................... 199
D.1 Specifications CLM HD8 ...........................................................................................................199
D.2 Specifications CLM 5 cable input (multi purpose).................................................................................201
D.3 Specifications CLM HDSDI – SDI input. . .. . .......................................................................................202
D.4 Specifications CLM DVI input ......................................................................................................203
D.5 Specifications CLM DVI HDCP input ..............................................................................................203
E. Troubleshooting. . ... . ... . ... . ... . .. . . .. . . .. . . .. . . .. . . .. . ... . ... . ... . ... . ... . .. . ... . ... . ... . ... . ... . .. . . .. . . .. . . .. . 205
E.1 Error codes . . .......................................................................................................................205
F. Mounting optional Carry handle.. . ... . ... . .. . . .. . . .. . . .. . ... . ... . .. . ... . ... . .. . . .. . . .. . . .. . ... . ... . .. . ... . ... . . 211
F.1 Mounting stacking points on top cover.............................................................................................211
F.2 Preparing the new carry handle . . ..................................................................................................212
F.3 Preparing the projector .............................................................................................................213
F.4 Mounting the carry handle..........................................................................................................214
G. Order info .......................................................................................................... 217
G.1 Spare partorder info ...............................................................................................................217
Glossary ............................................................................................................... 219
Index.................................................................................................................... 221
4 R59770057 CLM HD8 15/03/2010
1. SAFETY
About this chapter
Read this chapter attentively. It contains important information to prevent personal injury while installing and using an CLM HD8 projector. Furthermore, it includes several cautions to prevent damage to the CLM HD8. Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing your CLM projector. After this chapter, additional “warnings” and “cautions” are given depending on the installation procedure. Read and follow these “warnings” and “cautions” as well.
Overview
• General
• Important safety instructions
• Recycling guidelines
• Important warnings concerning CLM flight cases
1.1 General
Notice on safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, EN60950-1, UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology equipment including electrical business equipment. These safety standards impose important requirements on the use of safety critical components, materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard, and having access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of fire. Simulated single fault condition testing ensures the safety of the equipment to the user even when the equipment’s normal operation fails.
1. Safety
Installation instructions
• Before operating this equipment please read this manual thoroughly, and retain it for future reference.
• Installation and preliminary adjustments should be performed by qualified Barco personnel or by authorized Barco service deal­ers.
• All warnings on the projector and in the documentation manuals should be adhered to.
• All instructions for operating and use of this equipment must be followed precisely.
Definition of “qualified service technicians” or ”qualified technicians”: Persons having appropriate technical training and experience necessary to be aware of hazards to which they are exposed in performing a task and of measures to minimize the danger to themselves or other persons.
Owners record
The part number and serial number are located at the right side of the projector. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Barco dealer regarding this product.
Product article number
Product serial number
Dealer
R59770057 CLM HD8 15/03/2010 5
1. Safety
1.2 Important safety instructions
To prevent the risk of electrical shock
• Warn ing : This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power cables are the correct one, consult your dealer. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug. The wires of the power cord are colored in accordance with the following code:
International plug:
Green/Yellow: ground.
Blue: neutral.
Brown: line (live)
• Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself.
• If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugg extension cord does not exceed the extension cord ampere rating.
• Use only the power cord supplied with your projector. While appearing to be similar, other power cords have not been safety tested at the factory and may not be used to power the projector. For a replacement power cord, contact your dealer.
• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock.
• Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before resuming operations.
• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to th surges.
North American plug:
Green/Yellow or Green: ground.
Blue or White: neutral.
Brown or Black: line (live)
ed into the
e projector due to lightning and AC power-line
To prevent personal injury
• Caution: High pressure lamp may explode if improperly handled. Refer servicing to qualified service personnel. The customer should never attempt to disassemble the lamp casing or to dispose of the lamp casing other than by returning it to Barco.
• To prevent injury and physical damage, always read this manual and all labels on the system before inserting the lamp casing, connecting to the wall outlet or adjusting the projector.
• To prevent injury, take note of the weight of the projector. Minimum 2 persons are needed to carry the projector.
• To prevent injury, ensure that the lens and all cover plates are correctly installed. See installation procedures.
• Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.
• Before attempting to remove any of the projector’s covers, you must turn off the projector and disconnect from the wall outlet.
• When performing setup work to a ceiling mounted projector, to prevent injury caused by falling objects or the system, set out a keep out area.
• Consult a professional structural engineer prior to suspending the projector from a structure not intended for that use. Always ensure that the working load limit of the structure can handle the load of the projector.
• Never stack more than two (2) CLM projectors in a hanging configuration (truss) and never stack more than three (3) CLM projectors in a base stand configuration (table mount).
• The power input at the projector side is considered as the disconnect device. When required to switch off the projector, to access parts inside, always disconnect the power cord at the projector side. In case the power input at the projector side is not accessible (e.g. ceiling mount), the socket outlet supplying the projector shall be installed nearby the projector and be easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring.
• Do not place this equipment on an unstable cart, stand, or table. T possible injury to the user.
• When mounting the projector to the ceiling or to a rigging system, always mount security chains.
• Warning: Protection from ultraviolet radiation: Do not look directly in the light beam. The lamp contained in this product is an intense source of light and heat. One component of the light emitted from this lamp is ultraviolet light. Potential eye and skin hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unnecessary exposure. Protect yourself and your employees by making them aware of the hazards and how to protect themselves. Protecting the skin can be accomplished by wearing tightly woven garments and gloves. Protecting the eyes from UV can be accomplished by wearing safety glasses that are designed to provide UV protection. In addition to the UV, the visible light from the lamp is intense and should also be considered when choosing protective eye wear.
• Exposure to UV radiation: Some medications are known to make individuals extra sensitive to UV radiation. The American Conference of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure for an-8hour day to be less than 0.1 microwatts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to assure employees are not exposed to cumulative radiation levels exceeding these government guidelines.
he product may fall, causing serious damage to it and
6
R59770057 CLM HD8 15/03/2010
1. Safety
• Mercury Vapor Warnings: Keep the following warnings in mind when using the projector. The lamp used in the projector contains mercury. In case of a lamp rupture, explosion there will be a mercury vapor emission. In order to minimize the potential risk of inhaling mercury vapors:
- Ensure the projector is installed only in ventilated rooms.
- Replace the lamp module before the end of its operational life.
- Promptly ventilate the room after a lamp rupture, explosion has occurred, evacuate the room (particularly in case of a preg-
nant woman).
- Seek medical attention if unusual health conditions occur after a lamp rupture, explosion, such as headache, fatigue, short-
ness of breath, chest-tightening coughing or nausea.
• Cooling liquid circuit. The projector contains a cooling circuit filled with Blue antifreeze diluted 1,2 ethanediol (1/3 ethanediol – 2/3 Demi water). When the cooling circuit leaks, switch off the projector and contact a service technician. The liquid is not for household use. Keep out of reach of children. Harmful by oral intake. Avoid exposure to pregnant women. Avoid contact with eyes, skin and clothing. Avoid inhale of the noxious fumes.
• Never use the projector with its backside downwards. Forbidden area is +70° and -70° compared with the vertical axis.
To prevent projector damage
• If the Air Filters are not regularly replaced, the air flow inside the projector could be disrupted, causing overheating. Overheating may lead to the projector shutting down during operation.
• In order to ensure that correct airflow is maintained, and that the projector complies with electromagnetic compatibility (EMC) requirements, and for safety requirements, it should always be operated with all of it’s covers in place.
• Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
• Do not block the projector cooling fans or free air movement under and around the projector. Loose papers or other objects may not be nearer to the projector than 40 cm (16") on any side.
• The projector must always be mounted in a manner which ensures free flow of air into its air inlets and unimpeded evacuation of the hot air exhausted from its cooling system. Heat sensitive materials should not be placed in the path of the exhausted air. Leave at least a free safety area of 1 meter (40”) at the rear of the projector.
• Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the mains supply immediately. Do not operate the projector again until it has been checked by qualified service technicians.
• Consult a professional structural engineer prior to suspending the ceiling mount from a structure not intended for that use. Always ensure the working load limit of the structure supporting the projector.
• Do not use this equipment near water.
• Special care should be used when DLP projectors are used in the same room as high power laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices
• Save the original shipping carton and packing material; they will come in handy if you ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory.
• Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution.
• To ensure the highest optical performance and resolution, t coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.
• Never use the projector with its backside downwards. Forbidden area is +70° and -70° compared with the vertical axis.
• Never use the projector when not all four lamps are installed.
he projection lenses are specially treated with an anti-reflective
TM
in which case there is a loss of warranty.
To prevent battery explosion
• Danger of explosion if battery is incorrectly installed.
• Replace only with the same or equivalent type recommended by the manufacturer.
• Dispose of used batteries according to the manufacturer’s instruction.
To prevent fire hazard
• Warning “Risk of fire”. Do not place flammable or combustible materials near the projector ! This projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe. Exposing flammable or combustible mate ignition of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of the projector whereby no flammable or combustible materials are present. The exclusion zone must be not less than 40 cm (16”) for all Barco DLP projecto
• Do not cover the projector or the lens with any material while the projector is in operation.
• To reduce the lamp heat of the projector, switch the projector first to standby and let the projector lamp cool down for at least 5 minutes. Then the projector may be switched off with the power switch.
• Mount the projector in a well ventilated area away from sources of ignition and out of direct sun light.
• Never expose the projector to rain or moisture.
R59770057 CLM HD8 15/03/2010
rials into close proximity of this projector could result in the spontaneous
rs. The exclusion zone on the lens side must be at least 2 meter (80”).
7
1. Safety
• In the event of fire, use sand, CO2, or dry powder fire extinguishers; never use water on an electrical fire.
• This product should never be placed near or over a radiator or heat register.
• This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
• Projection rooms must be well ventilated or cooled in order to avoid build up of heat.
On servicing
• Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials and risk of electric shock.
• Refer all servicing to qualified service personnel.
• Fence off a restricted area of at least 3 meters around the projector using an eye-catching fence and “KEEP OUT” sig to prevent unauthorized persons coming near the projector during servicing.
• Unplug this product from the wall outlet and refer servicing to qualified service technicians under the following conditions:
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.
• Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replacement parts or authorized replacement parts which have the same characteristics as the Barco ori tions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty.
• Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
ginal part. Unauthorized substitu-
ns. This
1.3 Recycling guidelines
WARNING: Do not break or crush lamps because this may pose health and environmental risks when mercury
vapors are released.
CAUTION: To avoid breaking the lamps, repack carefully when storing and transporting them.
CAUTION: Lamps may not be disposed as normal household trash.
Contact your local waste disposal facility for information on the recycling program for HID (High Intensity Discharge ) lamps in your area.
Image 1-1
Disposal options for mercury-containing lamps
• Recycle through a municipal or solid waste district household hazardous waste collection program in accordance with local regulations.
• Direct shipment to lamp recycler
• Shipment through a hazardous waste transporter
8
R59770057 CLM HD8 15/03/2010
1.4 Important warnings concerning CLM flight cases
Important warnings concerning stacking/transporting CLM rental flight cases
• Stack maximum two (2) CLM rental flight cases high. Never higher.
• Surface on which flight case is standing must be level to ensure that the total load is evenly spread out among the four wheels. The surface must also be able to support the load safely.
• Before stacking or transporting flight cases, check the wheels and their fixation screws for wear or defects.
• Before stacking or transporting flight cases, check that the four lock handles on each flight case are in good working order and locked securely.
• When stacked, make sure the wheels of the upper flight case are precisely positioned in the stacking dishes of the flight case below.
•Stackedflight cases may not be moved. Before stacking, the lower flight case must already be in its final resting position before placing the second upon it.
• Never stack loaded flight cases in a truck or other transport medium, unless each flight case is rigidly strapped tight.
• In the event of a wheel breaking, flight cases must be rigidly strapped tight to prevent a stack collapsing.
• Use an appropriate forklift to raise flight cases and take the necessary precautions to avoid personnel injury.
1. Safety
R59770057 CLM HD8 15/03/2010
9
1. Safety
10 R59770057 CLM HD8 15/03/2010
2. GENERAL
About this chapter
Read this chapter before installing your CLM HD8. It contains important information concerning installation requirements for the CLM HD8, such as minimum and maximum allowed ambient temperature, humidity conditions, required safety area around the installed projector, required power net, compatible signal sources, etc.
Furthermore, careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system.
Overview
• Installation requirements
• Unpacking the projector
• Box content
• Projector configurations
• Projector air inlets and outlets
• Free download of Projector Toolset
2.1 Installation requirements
Ambient temperature conditions
The maximum allowed ambient temperature for an operating Barco CLM HD8 may not exceed +40 ºC (+104 ºF).
The minimum allowed ambient temperature for an operating Barco CLM HD8 may not drop below +10 ºC (+50 ºF).
The projector will not operate if the ambient air temperature falls outside this range (+10 ºC → +40 ºC or +50 ºF → +104 ºF). Be aware that room heat rises to the ceiling. Check if the temperature near the installation site is not excessive.
The minimum storage temperature is -35 ºC (-31 ºF) and the maximum storage tem
perature is +65 ºC (+149 ºF).
2. General
Humidity conditions
Storage: 0 to 98% relative humidity, non-condensing.
Operation: 0 to 95% relative humidity, non-condensing.
High Altitude
For an optimal performance of the CLM at high altitude, make sure that sufficient air flow is available (maximum ambient temperature 30°C).
Projector weight
Do not underestimate the weight of one Barco CLM HD8, which is on which the projector(s) has to be installed is capable of handling five (5) times the complete load of the complete system.
about ±31 kg (±68 lb.). Be sure that the table or truss installation
Power requirements
One Barco CLM HD8 (order number R9050130 and R90501301) requires 100-120/200-240V 12/8A 50/60Hz.
One Barco CLM HD8 (order number R90501305) requires 100-120/200-240V 16/8A 50/60Hz.
Clean air environment
A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors ventilation inlets. For installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines or similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading performance), then it is highly advisable and desirable to have this contamination removed prior to it reaching the projectors clean air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not a feasible solution then measures to relocate the projector to a clean air environment should be considered.
Only ever use the manufacturer’s recommended cleaning kit which has been specifically designed for cleaning optical parts, never use industrial strength cleaners on the pro components. Failure to take suitable precautions to protect the projector from the effects of persistent and prolonged air contam­inants will culminate in extensive and irreversible ingrained optical damage. At this stage cleaning of the internal optical units will be noneffective and impracticable. Dam and may deem the warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any repair. It is the clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne particles in the environment of the p knowingly neglect, abandon or improper use.
jector’s optics as these will degrade optical coatings and damage sensitive optoelectronics
age of this nature is under no circumstances covered under the manufacturer’s warranty
rojector. The manufacturer reserves the right to refuse repair if a projector has been subject to
R59770057 CLM HD8 15/03/2010
11
2. General
Which screen type ?
There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection applications.
Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a determined amount of light projected toward them. The ‘GAIN’ of a screen is the term used. Front and rear screens are both rated in terms of gain. The gain of screens range from a white matte screen with a gain of 1 (x 1) to a brushed aluminized screen with a gain of 10 (x 10) or more. The choice between higher and lower gain screens is largely a matter of personal preference and another consideration called the viewing angle. In considering the type of screen to choose, determine where the viewers will be located and go for the highest gain screen possible. A high gain screen will provide a brighter picture but reduce the viewing angle. For more information about screens, contact your local screen supplier.
What image size? How big should the image be?
The projector is designed for projecting an image size : minimum 2.2 meter (7.2 ft.) to maximum 10 .8 meter (35.4 ft.) (depending on the ambient light conditions), with an aspect ratio of 16 to 9 .
2.2 Unpacking the projector
What has to be done ?
At delivery the projector is packed in a cardboard box upon a wooden pallet and secured with banding and fastening clips. Futher­more, to provide protection during transport, the projector is surrounded with foam. Once the projector has arrived at the installation site, it has to be removed from the cardboard box and wooden pallet in a safe manner without damaging the projector.
Necessary tools
Side cutter
How to unpack the projector
1. Remove the banding around the carton box, by releasing the fastening clips.
2. Cut open the box but do not insert the cutter too deep, otherwise the projector could be damaged.
Image 2-1
3. Take out the cardboard box with the accessories such as manuals, remote control and power cord.
4. Take the projector out of the cardboard box and place it on a stable table.
12
R59770057 CLM HD8 15/03/2010
Image 2-2
5. Remove the foam rubber.
Save the original shipping carton and packing material, they will be necessary if you ever have to ship your projector. For maximum protection, repack your projector as it was originally packed at the factory.
2. General
A rubber foam inside a plastic bag is placed into the lens opening of the projector. It’s recommended to reuse this foam and plastic back each time you transport the projector. This to prevent intrusion of dust and foreign particles.
CAUTION: Always remove the lens before transporting the projector !
2.3 Box content
Content
• One Barco CLM HD8, weight ±31 kg (±68 lb.).
• One Remote Control Unit (RCU).
• Two AA size batteries for the RCU.
• Two power cord of 2.5 meter, one CEEC19 and one NEM6C19.
• One user manual.
• One safety manual.
Initial inspection
Before shipment, the projector was inspected and found to be free of mechanical and electrical defects. As soon as the projector is unpacked, inspect for any damage that may have occurred in transit. Save all packing material until the inspection is completed. If damaged is found, file claim with carrier immediately. The Barco sales and service office should be notified as soon as possible.
The packaging of the CLM HD8 is provided with a shock-watch label. If this shock-watch label was triggered (red colored at arrival) during transport, that indicates the package was possibly roughly handled by the trans­port company. In this case, the instructions mentioned on the label, should be followed, which are: adding a note on the transportation document and informing the transport company and the Barco sales and service office as soon as possible.
Mechanical check
This check should confirm that there are no broken knobs or connectors, that the cabinet and panel surfaces are free of dents and scratches, and that the operating panel are not scratched of cracked. The Barco sales and service office should be notified as soon as possible.
R59770057 CLM HD8 15/03/2010
13
2. General
2.4 Projector configurations
The different configurations
Depending on the installation the projector can be mounted in different ways, the 4 different configurations are:
1. Front / Table (F/T)
2. Front / Ceiling (F/C)
3. Rear / Table (R/T)
4. Rear / Ceiling (R/C)
For a ceiling mounted configuration, the optional carry handle kit is required.
Front projection
AUDIENCE
F/C
F/T
Image 2-3 Front projection
Rear projection
Image 2-4 Rear projection
SCREEN
FLOOR
AUDIENCE BACKSTAGE
SCREEN
FLOOR
R/C
R/T
14 R59770057 CLM HD8 15/03/2010
Positioning the projector
2. General
SW
PD
ACD
SCREENSCREEN
SHB
SCREEN
SHB
CD
FLOOR
SW
Image 2-5
On-Axis / Off-Axis projection
The position of the projector with reference to the screen may also be different depending on the installation. Basically the projector can be positioned in On-Axis or Off-Axis configuration. On-Axis configuration means that the projector is positioned so as to have the centre of the lens coincidi right. Several parameters can be calculated determining the position in any installation.
Formula to calculate the distance CD for On-Axis projection: CD=SH/2+B-A
ng with the centre of the screen. Off-Axis projection is obtained by shifting the lens up, down, left or
Shift range
The lens can be shifted with respect to the DMD (P) which result in a shifted image on the screen (Off-Axis). A 100% shift means that the centre point of the projected image is shifted by half the screen size. In other words, the centre point of the projected image falls together with the outline of the image in an On-Axis projection. Due to mechanical and optical limitations it’s recommended to keep the shift values within the field of view (F) as illustrated below. Within these shift ranges the projector and lens perform excellently. Configuring the projector outside these shift ranges will result in a slight decline of image quality.
R59770057 CLM HD8 15/03/2010
15
2. General
+130%
U
-90% +13.5%
L R
D
Image 2-6 Shift range
PDMD F Field of view
-24%
It’s mechanical possible to shift outside the recommended field of view, but this will result in a slightly decline of image quality depending on the used lens and the zoom posit too much in both directions will result in a blurred image corner.
P
F
Horizontal and vertical projector tilt ranges
The projector is designed to work in a table or ceiling mounte inside the forbidden area A.
F
P
U
SIDE VIEW
D
F
P
L
TOP VIEW
+130%
-24%
-90%
R
+13.5%
ion of the used lens. Furthermore, shifting
d position, but tilting is allowed. Never tilt the backside of the projector
360°
A
140°
Image 2-7 Tilt area
16 R59770057 CLM HD8 15/03/2010
2.5 Projector air inlets and outlets
Air inlets and outlets
Image 2-8
The CLM HD8 has 2 inlet channels and one air outlet. The air outlet is located at the rear of the projector. The air inlets are located at the front and top of the projector.
2. General
2.6 Free download of Projector Toolset
About Projector Toolset
Projector Toolset is a software tool to set up, configure, manage and control Barco projectors.
The concept of this Projector Toolset software is modular. The basic package can be extended with several optional device plug-in modules, now and in the future available.
The Projector Toolset software works with configurations that can be loaded. Within a confi guration, different snapshots can be taken. A snapshot represents a current state of a configuration and can be reloaded to return to this typical state. These terms will be used through the complete software.
Projector Toolset is a stand-alone application that runs on a Java Virtual Machine and that does not require extra services to run.
Several configurations can be controlled simultaneously. Even when the configurations are connected via different ways.
Projector Toolset is only available in a download version, no CD can be ordered.
Where to find the download file(s)
The program and all necessary plug-ins, as well as the Reference manual can be downloaded for free from Barco’s Partnerzone, URLh
ttps:\\my.barco.com. Registration is necessary.
If you are not yet registered, click on Partnerzone registration and follow the instructions. With the created login and password, it is possible to enter the partnerzone where you can download the Projector Toolset software and the device plug-in updates as well as the corresponding reference manual.
When downloading the complete Projector Toolset, this software contains already the latest device plug-ins. When you already have the latest core version of Projector Toolset, it is possible to download only device plug-in updates from the same web site location.
As Projector Toolset is a stand alone application, it is not necessary to install any other software. A Java virtual machine is included with this download.
Installation
Download first the reference manual (Part number: R59770052) and follow the installation instructions as written in this manual.
R59770057 CLM HD8 15/03/2010
17
2. General
18 R59770057 CLM HD8 15/03/2010
3. Physical installation
3. PHYSICAL INSTALLATION
About this chapter
This chapter explains how to install and set up your CLM projector. If you are familiar with the projector and want to quickly set it up for temporary use, follow the “Quick setup” instructions below. For a more complete setup, follow the instructions and guides covered in the remaining subsections.
Quick setup
The following steps describe briefly how to setup your CLM projector in a table mount front projection. Note that each step refers to a corresponding procedure, which is more detailed and illustrated.
1. Install the batteries of the remote control, see "RCU battery installation", page 20.
2. Place the projector on a solid table in front of the screen at the expected throw distance. Ensure that the projector is installed at right angles (horizontally and vertically) with the screen.
3. Select and install an appropriate lens, which covers the throw ratio ( = screen size / projector screen distance). For more details see "Lens selection", page 23.
4. Connect the projector with the local power net, see "Power connection", page 35.
5. Connect your source to the appropriate input module, see "Input source connections", page 37.
6. Switch ON the projector, see procedure "Switching on", page 45.
7. Select the input slot at which your source is connected with. Do this by pressing the numeric key “1” or “2” on the remote control unit or on the local keypad, see "Source selection", page 53.
8. Zoom and shift the lens until the image is properly projected on the screen, Do this by using the “ZOOM” and “FOCUS” key on the remote control unit or on the local keypad, see"Quick Lens Adjustment via LENS key", page 48 or "Direct Lens Adjustment (RCU)", page 49. If necessary, level the projector from side to side by turning the adjustable feet in or out, see "Alignment of a table mounted CLM projector", page 24.
Overview
• Remote control unit (RCU)
• Lenses
• Alignment of a table mounted CLM projector
• Suspension of the CLM projector with rigging clamps
• Alignment of a ceiling mounted CLM projector
3.1 Remote control unit (RCU)
Introduction
The standard remote control unit (A) can be equipped with the
The remote control unit can be used wired via mini-jack or via optional rugged XLR. Note that the backlight of the remote control unit illuminate continuously when used with a wire.
A
optional rugged case (B) and an XLR adapter (C).
B
C
Image 3-1
R59770057 CLM HD8 15/03/2010 19
3. Physical installation
Overview
• RCU battery installation
• RCU rugged case installation
• RCU XLR adaptor installation
• Using the XLR adaptor of the RCU
• RCU usage possibilities
3.1.1 RCU battery installation
Where to find the batteries for the remote control ?
The batteries are not placed in the remote control unit to avoid control operation in its package, resulting in a shorter battery life time. At delivery the batteries can be found in a separated bag attached to the remote control unit. Before using your remote control, install the batteries first.
How to install the batteries in the remote control ?
1. Push the battery cover tab with the fingernail a little backwards (1) and pull, at the same time, the cover upwards (2).
1
Image 3-2
2. Insert the two AA size batteries, making sure the polarities match the + and - marks inside the battery compartment.
+
-
Image 3-3
3. Insert (1) the lower tab of the battery cover in the g
in place.
+
-
ap at the bottom of the remote control, and press (2) the cover until it clicks
2
2
1
-
Image 3-4
+
­+
To prevent battery explosion
• Danger of explosion if battery is incorrectly installed.
• Replace only with the same or equivalent type recommended by the manufacturer.
• Disposal of used batteries must be done according to the manufacturer’s instruction.
20
R59770057 CLM HD8 15/03/2010
3. Physical installation
3.1.2 RCU rugged case installation
Only with optional rugged case kit which is part of the touring kit (R9861000).
Necessary tools
No tools.
Necessary parts
Touring kit
How to install the rugged case of the remote control ?
1. Slide the bottom of the RCU into the rugged case and then pull the top of the rugged case over the top of the RCU as illustrated.
Image 3-5
3.1.3 RCU XLR adaptor installation
Install the rugged case before installing the X the rugged case from the RCU.
LR adaptor. Vice-versa, remove the XLR adaptor before removing
Necessary tools
5mmflat screw driver.
Necessary parts
XLR adapter (part of the touring kit)
How to install the XLR adaptor of the remote control unit ?
1. Push the XLR adaptor (C) upon the rugged case of the remote control unit as illustrated.
Note: Ensure that the text of the XLR adaptor is on top.
R59770057 CLM HD8 15/03/2010
21
3. Physical installation
C
S
Image 3-6 Mounting the XLR adapter
2. Fasten the two screws (S) of the XLR adaptor. Turn each screw repeatedly one or two turns until both screws are tight.
3.1.4 Using the XLR adaptor of the RCU
How to use the XLR adaptor of the remote control unit ?
1. Connect a cable with XLR plug into the XLR adaptor.
2. Connect the other end of the cable with your CLM HD8.
3. Push the XLR adaptor completely against the rugged case of the remote control unit, as illustrated in the left image below, for wired communication. Pull out the XLR adaptor (about 8 mm) to switch over to wireless communication.
S
Image 3-7
3.1.5 RCU usage possibilities
Summarized possibilities
Possibility description
Ref.
a.
RCU not wired
b.
RCU wired (mini-jack) Backlight illuminates continuously whe
c.
RCU with rugged case not wired
d. RCU with rugged case wired (mini-jack) Backlight illuminates continuously when wire is connected. Infra red
e.
RCU with rugged case and XLR adaptor pulled out “REMOTE” and not wired
f. RCU with rugged case and XLR adapto
pulled out “REMOTE” and wired
g.
RCU with rugged case and XLR adaptor pushed in “WIRED” and wired
22
Comment
disabled.
disabled.
The XLR adaptor must be in the pulled out position “REMOTE”, otherwise the RCU will not function.
r
The RCU will send the commands via i
The RCU will send the commands via the cable connected with the XLR adaptor to the projector. Backlight illuminates continuously when wire is connected. Infra red disable
n wire is connected. Infra red
nfra red to the projector.
d.
R59770057 CLM HD8 15/03/2010
abcd fge
Image 3-8
3.2 Lenses
3. Physical installation
Overview
• Available lenses
• Lens selection
• Lens formulas
3.2.1 Available lenses
Overview
Lens
CLD 1.2 - 1.5
CLD 1.5 - 2.2
CLD 2.2 - 4.4
CLD 4.4 - 7.0
Order number
R9861060
R9861070
R9861080
R9861090
3.2.2 Lens selection
How to select the right lens for your application
1. Determine the required screen width (SW).
2. Determine the position of the projector in the projection room with regard to the screen and measure the projector-screen distance (PD).
3. Use the lens formulas to find the best corresponding PD with regard to the measured projector-screen distance for the required screen width SW.
Tip: Divide PD by SW to determine the approximate throw ratio. Choose a Lens, which captures the calculated throw ratio.
Use the lens formula of the chosen Lens to recalculate exactly.
R59770057 CLM HD8 15/03/2010
23
3. Physical installation
SCREEN
Image 3-9 PD for lens selection
3.2.3 Lens formulas
Formulas
Lens
CLD (1.2 - 1.5 : 1)
CLD (1.5 - 2.2 : 1)
CLD (2.2 - 4.4 : 1)
CLD (4.4 - 7.0 : 1)
CAUTION: Never transport the projector with a Lens mounted in the Lens Holder. Always remove the Lens
before transporting the projector. Neglecting this can damage the Lens Holder and Prism.
PD
Throw ratio for CLM HD8
1.15 - 1.46
1.45 - 2.18
2.07 - 4.12
4.07 - 6.39
SW
Metric formulas (meter) Inch formulas (inch)
PD
=1.15 x SW - 0.13
min
=1.46 x SW - 0.05
PD
max
PD
=1.45 x SW - 0.01
min
=2.18 x SW - 0.53
PD
max
PD
=2.07 x SW - 0.07
min
=4.12 x SW - 0.13
PD
max
PD
=4.07 x SW - 0.25
min
=6.39 x SW - 0.04
PD
max
PD
=1.15 x SW - 5.12
min
=1.46 x SW - 1.97
PD
max
PD
=1.45 x SW - 0.39
min
=2.18 x SW - 20.87
PD
max
PD
=2.07 x SW - 2.76
min
=4.12 x SW - 5.12
PD
max
PD
=4.07 x SW - 9.84
min
=6.39 x SW - 1.58
PD
max
3.3 Alignment of a table mounted CLM projector
How to align a table mounted CLM projector
1. Place the projector in the desired location. Take into account the zoom range of the used lens and the size of the screen.
2. Project one of the internal hatch patterns on the screen.
3. Turn the adjustable feet in or out until the projected hatch pattern is perfectly rectangle shaped and leveled.
Image 3-10 Level adjustment
24 R59770057 CLM HD8 15/03/2010
When this is achieved, the projector is set horizontal and vertical at right angles to the screen.
3. Physical installation
SCREEN
Image 3-11
3.4 Suspension of the CLM projector with rigging clamps
Before the projector can be suspended, the optional carry handle must be mounted on the projector. For more information about the optional carry handle, see "Mounting optional Carry handle", page 211.
CAUTION: Consult a professional structural engineer to ensure that the suspension system is suitable for
this task.
Rigging points and rigging clamps
The carry handle is provided with six slots. Four slots are longitudinally oriented (A) and two slots are transversely oriented (B). In each slot, a rigging point can be inserted (this rigging point is m depending of the size of the truss installation. The rigging clamps turn in these rigging points and these clamps allow an easy and fast physical setup of the projector in a hanging configuration.
ounted on the clamps) and the position in the slot can be adjusted
SCREEN
A
B
A
Image 3-12 Riggingslotsandclamps
Necessary tools
Open end spanner 17 mm
Necessary parts
• Four rigging clamps (R855943)
• Safety cable (B361213)
• Two snap hook locks (B361212)
Mounting the rigging points into the handle
1. Push the cup square neck bolt through the slot input and slide the bolt into the slot.
Note: Take the bolt by its thread so that it does not fall inside the carry handle.
C
R59770057 CLM HD8 15/03/2010
25
3. Physical installation
Image 3-13 Mount rigging points
The cover plate will move down while pushing with the head but comes back to its position once the bolt is in the slot.
2. Slide a washer on the bolt and turn on a nut.
3. Measure the distance, center tube as reference, between the two used support bars of the truss.
X mm
Image 3-14
4. Slide the rigging points on there place in the slots, according the measured distance and secure this position by fastening the nut completely. Ensure that the rigging points are symmetrically lined up, so that the projector will hang in balance. If necessary move point B from a transversal position to a longitudinal position.
Warning: Always secure the rigging points after adjustment.
x mm
Image 3-15 Set up truss width
5. Turn the rigging clamps
26
on the bolts.
A
B
R59770057 CLM HD8 15/03/2010
Loading...
+ 201 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use