Barbie BAR710 User Manual 2

BAR710

Barbie and associated trademarks and trade dress are owned by, and used under
license from, Mattel, Inc. ©2007 Mattel, Inc. All Rights Reserved.

OWNER'S MANUAL

Petal Sound System for iPod

TM

®

See page 20

for your hidden

GEMSTONE FUN

button surprise!

SAFETY

INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

DANGEROUS VOLTAGE:

The lightning flash with arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of
uninsulated dangerous voltage within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.

ATTENTION:

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

CAUTION–ELECTRICALLY OPERATED PRODUCT:

Not recommended for children under 5 years of age. As with all electric
products, precautions should be observed during handling and use to
prevent electric shock.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.

The Caution Marking is located at the bottom enclosure
of the apparatus.

iPod is a trademark of Apple Computer, Inc., registered in the U.S. and
other countries.

1

SAFETY INSTRUCTIONS

Before using the unit, be sure to read all
operating instructions carefully. Please note
that these are general precautions and may
not pertain to your unit. For example, this unit
may not have the capability to be connected
to an outdoor antenna.

1. READ INSTRUCTIONS

All the safety and operating instructions
should be read before the product
is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be
retained for future reference.

3. HEED WARNINGS

All warnings on the product and in the oper­ating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should
be followed.

5. CLEANING

Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a dry cloth for cleaning.

6. ATTACHMENTS

Do not use attachments not recommended
by the product's manufacturer as they may
cause hazards.

7. WATER AND MOISTURE

Do not use this product near water–for
example: near a bathtub, washbowl, kitchen
sink or laundry tub; in a wet basement; or
near a swimming pool.

8. ACCESSORIES

Do not place this product on an unstable cart,
stand, tripod, bracket or table. The product
may fall, causing serious injury and serious
damage to the product. Use only with a cart,
stand, tripod, bracket or table recommended
by the manufacturer or sold with the product.
Any mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by
the manufacturer.

8A. An appliance and cart

combination should be
moved with care. Quick
stops, excessive force and
uneven surfaces may cause
the appliance and cart
combination to overturn.

9. VENTILATION

Slots and openings in the cabinet and in the

back or bottom are provided for ventilation, to
ensure reliable operation of the product and
to protect it from overheating. These
openings must not be blocked or covered.
The openings should never be blocked by
placing the product on a bed, sofa, rug or
other similar surface. This product should
never be placed near or over a radiator or
heat source. This product should not be
placed in a built-in installation such as a
bookcase or rack unless proper ventilation is
provided or the manufacturer's instructions
have been adhered to.

10. POWER SOURCES

This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type
of power supply to your home, consult your
appliance dealer or local power company. For
products intended to operate from battery
power, or other sources, refer to the
operating instructions.

11. GROUNDING OR POLARIZATION

This product is equipped with a polarized
alternating-current line plug (a plug having
one blade wider than the other). This plug will
fit into the power outlet only one way. This is
a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
polarized plug.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that
they are not likely to be walked on or pinched
by items placed upon or against them, paying
particular attention to cords at plugs,
convenience receptacles, and the point
where they exit from the appliance.

13. LIGHTNING

To protect your product from a lightning
storm, or when it is left unattended and
unused for long periods of time, unplug it
from the wall outlet and disconnect the
antenna or cable system. This will prevent
damage to the product due to lightning and
power-line surges.

14. POWER LINES

An outside antenna system should not be
located in the vicinity of overhead power lines
or other electric light or power circuits, or

2

SAFETY INSTRUCTIONS

where it can fall into such power lines or
circuits. When installing an outside antenna
system, extreme care should be taken to
keep from touching such power lines or
circuits as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension
cords as this can result in a risk of fire or
electric shock.

16. OBJECT AND LIQUID ENTRY

Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short out parts that could result
in fire or electric shock. Never spill or spray any
type of liquid on the product.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna is connected to the
product, be sure the antenna system is
grounded so as to provide some protection
against voltage surges and built-up static
charges. Section 810 of the National Electric
Code, ANSI/NFPA 70, provides information
with respect to proper grounding of the mast
and supporting structure, grounding of the
lead-in wire to an antenna discharge product,
size of grounding conductors, location of
antenna discharge product, connection to
grounding electrodes and requirements for
grounding electrodes.

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

18. SERVICING

Do not attempt to service this product
yourself as opening or removing covers may
expose you to dangerous voltage or other
hazards. Refer all servicing to qualified
service personnel.

19. REPLACEMENT PARTS

When replacement parts are required, be

sure the service technician uses replacement
parts specified by the manufacturer or those
that have the same characteristics as the
original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to
this product, ask the service technician to
perform safety checks to determine that the
product is in proper operating condition.

21. WALL OR CEILING MOUNTING

The product should be mounted to a wall or
ceiling only as recommended by
the manufacturer.

22. DAMAGE REQUIRING SERVICE

Unplug the product from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
a. When the power-supply cord or plug is

damaged.

b. If liquid has been spilled or objects have

fallen into the product.

c. If the product has been exposed to rain or

water.

d. If the product does not operate normally

by following the operating instructions.
Adjust only those controls that are
covered by the operating instructions, as
an adjustment of other controls may result
in damage and will often require
extensive work by a qualified technician
to restore the product to its normal
operation.

e. If the product has been dropped or the

cabinet has been damaged.

f. When the product exhibits a distinct

change in performance–this indicates a
need for service.

23. HEAT

The product should be situated away from
heat sources such as radiators, heat
registers, stoves or other products (including
amplifiers) that produce heat.

24. NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV
system installer's attention to Article 820-40
of the NEC that provides guidelines for
proper grounding and, in particular, specifies
that the cable ground shall be connected to
the grounding system of the building, as
close to the point of cable entry as practical.

3

SAFETY INSTRUCTIONS

FCC WARNING:

This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user
could lose the authority to operate this equipment if an unauthorized
change or modification is made.

FCC INFORMATION:

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

4

Dear Customer:

A

S

S

O

C

I

A

T

I

O

N

EST. 1924

E

L

E

C

T

R

O

N

I

C

I

N

D

U

S

T

R

I

E

S

EIA

We

LISTENING

For A Lifetime

Want You

Selecting fine audio equipment such as the unit you’ve just purchased is only the start of
your musical enjoyment. Now it’s time to consider how you can maximize the fun and
excitement your equipment offers. This manufacturer and the Electronic Industries
Association’s Consumer Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through loud and clear without
annoying blaring or distortion and, most importantly, without affecting your sensitive
hearing. Sound can be deceiving. Over time your hearing “comfort level” adapts to higher
volumes of sound. So what sounds “normal” can actually be loud and harmful to your
hearing. Guard against this by setting your equipment at a safe level BEFORE your
hearing adapts.

To establish a safe level:

• Start your volume control at a low setting.

• Slowly increase the sound until you can hear it comfortably and clearly, and
without distortion.

Once you have established a comfortable sound level:

• Set the dial and leave it there.

Taking a minute to do this now will help to prevent hearing damage or loss in the future.
After all, we want you listening for a lifetime.

We Want You Listening For A Lifetime

Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s Consumer Electronics Group recommend you
avoid prolonged exposure to excessive noise. This list of sound levels is included for
your protection.

Decibel

Level

30 Quiet library, soft whispers

Example

40 Living room, refrigerator, bedroom away from traffic
50 Light traffic, normal conversation, quiet office
60 Air conditioner at 20 feet, sewing machine
70 Vacuum cleaner, hair dryer, noisy restaurant
80 Average city traffic, garbage disposals, alarm clock at two feet

THE FOLLOWING NOISES CAN BE DANGEROUS UNDER
CONSTANT EXPOSURE:

90 Subway, motorcycle, truck traffic, lawn mower
100 Garbage truck, chain saw, pneumatic drill
120 Rock band concert in front of speakers, thunderclap
140 Gunshot blast, jet engine
180 Rocket launching pad

Information courtesy of the Deafness Research Foundation.

5

Emerson Radio Corp. has produced this audio product under

0-5

license from Mattel. We have taken great care to make sure your
unit was in perfect working order when it left our factory.

It has been designed to give you many years of enjoyment and
trouble-free operation. Read this manual before operating this unit
to become familiar with its features. In the event you require
technical assistance, please contact the Emerson Radio Customer
Service hotline at 1-800-898-9020. Retain this manual for
future reference.

WARNING

Choking Hazard–Small Parts and Packaging Materials. Not for children
under 5 years.

• All materials for fastening or packing purposes are not part of the unit and
should be discarded for children’s safety.

• Please keep all information for future reference.

• This is not a toy.

NOTES:

• Please avoid using this unit in places of high temperature or humidity

over prolonged periods of time as damage may occur.

• Exposure to direct sunlight in places such as car interiors may cause the

unit to become warped and/or lead to malfunctioning.

• Avoid using or storing this unit in dusty or sandy locations.

PROTECT YOUR FURNITURE

This model is equipped with non-skid rubber “feet” to prevent the product from
moving when you operate the controls. These “feet” are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives
or cleaning sprays may cause the rubber “feet” to soften and leave marks or a rubber
residue on your furniture. To prevent any damage to your furniture, we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber “feet” before you place the product on fine wooden furniture.

6

LOCATION OF CONTROLS

1

2
3
4
5

6
7

8
9

10

11
12

13
14

15
16
17

18
19

20
21

1. Left Speaker

2. ALARM SET Button

3. ALARM ON/OFF Button

4. AC Cord (Rear of Unit)

5. SLEEP Button

6. VOLUME Control (Side of Unit)

7. STANDBY ON Button

8. SNOOZE Button

9. Display

10. GEMSTONE FUN Button

11. Right Speaker

12. iPod Compartment with

Connector & Interchangeable
Universal Docks

13. Battery Compartment

(Bottom of Unit)

14. TIME SET Button

15. HOUR/Skip/Search

16. TUNING Control (Side of Unit)

o Button

17. MINUTE/Skip/Search

18. PHONE (Headphones), AUX IN
and VIDEO OUT Jacks
(Rear of Unit)

19. PLAY/PAUSE Button

20. iPod/AUX/AM/FM Button

21. Light Ring

n Button

7

LOCATION OF CONTROLS (CONTINUED)

1

2

3

4

5

6

LCD Display

1. PM Indicator

2. AM/FM Band Indicators

3. Time Display

4. Frequency Display

5. Alarm Indicator

6. SLEEP/STEREO/AUX/iPod/Radio/Buzz Indicators

8

POWER SOURCE

AC Plug

AC Outlet

AC CONNECTION

Use the AC polarized line cord for operation on
AC power. Insert the AC plug into any
convenient 120V 60Hz household outlet.
NOTE: The AC plug supplied with the unit is
polarized to help minimize the possibility of
electric shock. If the AC plug does not fit into a
nonpolarized AC outlet, do not file or cut the
wide blade. It is the user’s responsibility to
have an electrician replace the obsolete outlet.

BATTERY INSTALLATION

Two (2) “AAA” size batteries can also be used to
power and/or to provide a backup for the clock and
alarm time for this unit as follows:

1. Open the battery door by removing the screw
and then sliding the battery door off in the
direction of the “OPEN” arrow.

2. Insert two (2) “AAA” batteries as shown. Alkaline
batteries are recommended for the longest
playing time.

3. Replace the battery door and screw back on
the compartment.

NOTE:

• The batteries are used to back-up the clock and

alarm times when the AC adapter is disconnected
or there is a power failure.

9

OPTIONAL CONNECTIONS

PHONE (Headphones) JACK

For private listening, plug headphones into this jack. The speakers will be
disconnected when a plug is inserted into this jack.

AUX IN JACK

Insert one end of the audio cable (included) into the LINE OUT jack on your
external audio unit and the other end into the AUX IN jack on the rear of
this unit.
To listen to the external audio unit, turn this unit on using the STANDBY ON
button. Turn on the external unit as well. Then, select “AUX” by repeatedly
pressing the iPod/AUX/AM/FM button; “AUX” will appear in the display. The
external audio unit’s output sound will be heard through this unit’s
speakers. If you wish to listen to the iPod in the iPod compartment, select
“iPod” by repeatedly pressing the iPod/AUX/AM/FM button; “iPod” will
appear in the display.

VIDEO OUT JACK

If you are using an iPod with video (5th generation) or iPod photo, you can
connect this unit to an external TV with the video cable (included). You will
then be able to view the photos (in Slideshow mode)/videos from the iPod
on your external TV.

NOTES:

• Set the TV’s TV/VIDEO button or switch to the VIDEO setting.

• When connecting this unit, refer to the owner’s manual of the TV, as well
as this manual.

• When connecting this unit to the TV, make sure the power is off and both
units are unplugged before making any connections.

• Make sure to go into the Settings menu of your iPod and set the TV Out
setting to ON and set the TV signal to NTSC; otherwise, you may not be
able to view the photos (in Slideshow mode)/videos on your external TV.

10

INSERTING AN iPod

(A)

(B)

(A)

(B)

(B)

(A)

(B)

1

Locate the correct Universal Dock
to use as shown on page 21.
Insert the Universal Dock (A) into
the iPod compartment (B) (as
shown), making sure the tabs are
facing front, and slip the tabs into
place. Press the rear side of the
Universal Dock until it is
positioned inside the iPod
compartment.

3

Slide the iPod (A) into the
Universal Dock (B) (as shown).
Gently push down so the
connector on the iPod slides onto
the connector on this unit.

NOTES:

• For better AM radio reception, the iPod will not charge while in AM radio mode.

• To remove the Universal Dock, insert your finger (or other object) into the gap

in the Universal Dock, then gently pull the Universal Dock out to remove it.

2

Insert the iPod Support Bracket
(A) into the two holes behind the
iPod Compartment (B) (as shown).

4

The iPod will charge as long as
this unit is connected via the
AC cord.
Please see the next page for
instructions on using an iPod with
this unit.

11

OPERATION

1

2

1

2

USING AN iPod WITH THIS UNIT

1

With an iPod connected (see previous
page), if this unit is not already on, turn
this unit on by pressing the STANDBY
ON button
iPod mode, select “iPod” by repeatedly
pressing the iPod/AUX/AM/FM button

2; “iPod” will appear in the display.

1. If you are not already in

3

To play/pause the iPod:

Press the PLAY/PAUSE button to
start playback on your iPod. Press
again to pause playback and
press yet again to resume
playback.

NOTES:

• If an iPod is inserted while this unit is already on and in iPod mode, iPod
playback mode will begin automatically.

• See the next page for how to adjust the volume.

• To turn this unit off, press the STANDBY ON button.

2

You can operate the iPod using
its own controls, as per its
owner’s manual, or you can use
the controls on the main unit to
operate the iPod.

4

To skip forward or backward on
the iPod:

Skip/Search
Skip/Search
beginning of the current track/
previous or next track.

To search forward or backward on
the iPod:

HOUR/Skip/Search
MINUTE/Skip/Search
search within the currently­playing track.

Press the HOUR/

o 1 or MINUTE/

n 2 button to skip to the

Press and hold the

o 1 or

n 2 button to

12

OPERATION (CONTINUED)

ADJUSTING THE VOLUME

1

To adjust the volume:

Rotate the VOLUME control as
desired to increase and/or
decrease the volume.

13

OPERATION (CONTINUED)

USING THE RADIO

1

Turn this unit on by pressing the
STANDBY ON button.

2

If you are not already in AM or FM mode,
select “AM” or “FM” by repeatedly
pressing the iPod/AUX/AM/FM button;
“AM” or “FM” and the frequency will
appear in the display.

3

Rotate the TUNING control to
manually advance the frequency in
the display up or down until the
desired frequency appears.
NOTE: When a station is tuned, after
approx. five seconds, the radio
frequency will disappear and the
actual time will reappear in the
display. If you rotate the TUNING
control, the radio frequency will
appear in the display again.

NOTES:

• See the previous page for how to adjust the volume.

• To turn this unit off, press the STANDBY ON button.

ANTENNAS
FM:

The FM antenna is built into the AC cord. You may have to extend and vary the direction
of the AC cord until you find the position that provides the best reception.
AM: The AM bar antenna is located inside the cabinet of the main unit. You may need to
change the position of the main unit until you find the position that provides the best
reception of your favorite AM stations.

14

OPERATION (CONTINUED)

2

1

TO SET OR RESET THE ACTUAL TIME

1

With the power off, press the
TIME SET button; the time
will blink.

3

Press the TIME SET button (or
wait approx. 10 seconds) and the
time will be set.

2

Within 10 seconds, press the
MINUTE/Skip/Search
to set the present minute and the
HOUR/Skip/Search
set the present hour. Make sure to
set the correct AM/PM setting.

n button 1

o button 2 to

15

OPERATION (CONTINUED)

2

1

3

2

1

4

3

2

1

3

TO SET OR RESET THE ALARM TIME

1

With the power off, press the
ALARM SET button; the Alarm
time will blink in the display.

3

Within 10 seconds, press the
MINUTE/Skip/Search
and/or HOUR/Skip/Search o
button 2 to set the alarm mode
(iPod, Buzz[er] or Radio). Press
the ALARM SET button

n button 1

3 again.

2

Within 10 seconds, press the
MINUTE/Skip/Search
to set the alarm minute and the
HOUR/Skip/Search
set the alarm hour. Make sure to
set the correct AM/PM setting.
Press the ALARM SET button

3 again.

n button 1

o button 2 to

4

If set to Radio, within 10 seconds, set

the band (AM or FM) using the
MINUTE/Skip/Search
and/or HOUR/Skip/Search o button 2,
followed by pressing the ALARM
SET button
5 seconds). (When the alarm time is
reached, the unit will turn on the band
(AM or FM) that you selected and the
frequency that you had selected before
turning the unit off.)

Repeatedly press the ALARM ON/OFF
button

3 again (or waiting approx.

4 to turn the alarm on or off.

n button 1

CONTINUED ON THE NEXT PAGE

16

OPERATION (CONTINUED)

5

If set to iPod, insert the iPod as shown

on page 11. Select your desired track and
then make sure both your iPod and this
unit are turned off. When the alarm time
is reached, this unit will start playback on
the track that you selected.

NOTES:

• If set to iPod but an iPod is not connected, the unit will automatically switch

to wake to Buzzer.

• Make sure to set the desired volume as shown on page 13.

TO SHUT OFF THE ALARM, see TO SHUT THE ALARM OFF section on

•

the next page.

17

OPERATION (CONTINUED)

1

2

TO SHUT THE ALARM OFF

1

To leave the alarm set for the next
day, press the STANDBY ON button
1 or ALARM ON/OFF button 2 and
the alarm will turn off but be set for
the next day.

SNOOZE

1

While the alarm is sounding, press the
SNOOZE button. The alarm will turn
back on automatically nine minutes later
until the SNOOZE function is cancelled.

NOTES:

• You can repeat the SNOOZE
function for up to 60 minutes.

• To cancel the SNOOZE function (the

alarm will not turn back on), press the
ALARM ON/OFF button.

2

To NOT set the alarm for the next
day, press the ALARM ON/OFF
button again to select alarm off (no
indicator in the display).

18

OPERATION (CONTINUED)

SLEEP

1

While the unit is on, press the SLEEP
button; “SLEEP” will appear and "120"
will blink in the display which indicates
the SLEEP feature is on and set for 120
minutes (the unit will turn off
automatically after 120 minutes).
To set a shorter SLEEP time, press the
SLEEP button again within five seconds
to select 90 minutes; "90" will blink in the
display. Repeat to select 60, 30, 20, 10
or 5 minutes. (If you press the SLEEP
button again while “05” is blinking in the
display, the unit will turn off immediately.)
To view the remaining SLEEP time,
press the SLEEP button once.

19

OPERATION (CONTINUED)

See what you

c

an do with

y

our GEMSTONE

FUN button!

Step 1

Step 1

Step 2

BarbieTMhas a surprise just for you!
Just follow the instructions below and
see what you can do with your
GEMSTONE FUN button!

Press the GEMSTONE FUN button
on your iPod sound system.

SURPRISE! The pink light ring
around your iPod sound system will
light up!

NOTE:
Press the GEMSTONE FUN button
again to turn the light ring off.

20

OPERATION (CONTINUED)

iPod Type Memory Univ. Dock No.

20GB/
U2
Special
Edition
20GB

40GB

Fourth
Generation
iPod

20GB,
30GB,
U2
Special
Edition

40 to
60GB

3, “3G iPod (10/15GB)
4G iPod (20GB)
iPod photo (20/30GB)”

2, “3G iPod (30/40GB)
4G iPod (40GB)”

iPod
photo/
iPod with
color
display

3, “3G iPod (10/15GB)
4G iPod (20GB)
iPod photo (20/30GB)”

4, “iPod photo (40GB)
iPod photo (60GB)”

4to
6GB

iPod
mini

5, “iPod mini”

iPod UNIVERSAL DOCKS

Locate your iPod in the chart below and select the respective Universal Dock
(the Universal Dock No. is engraved at the front of the Universal Docks as
shown on the next page) to match with your iPod. Insert the corresponding
Universal Dock and your iPod into the unit as described on page 11.

PLEASE SEE THE NEXT PAGE FOR IMPORTANT NOTES

AND THE LOCATION OF THE UNIV. DOCK NO.

21

OPERATION (CONTINUED)

2

NOTES:

• The Third Generation iPod 10-15GB uses the same dock as the Fourth
Generation iPod 20GB. Also, the Third Generation iPod 30-40GB uses
the same dock as the Fourth Generation iPod 40GB.

• For the iPod nano and for the iPod video (Fifth Generation), please use
the universal docks included with your iPod.

• Also included with this unit is a dock for use with the Barbie
MP3 player
also a “dust cover” (a dock with no opening for an iPod) included with
this unit; it is marked on the bottom as “1” and on the front as “iPod
cover”. Please insert the “dust cover” into the iPod compartment if you
will not be using an iPod with this unit for an extended amount of time.

TM

; it is marked on the bottom as “MP3 Player, 6”. There is

IMPORTANT! The Universal Dock No. is engraved at the front of the
docks. Please refer to the illustration below for the location of the
Universal Dock No.

TM

Petal

22

TROUBLESHOOTING GUIDE

If you experience a problem with this unit, check the chart below
before calling for service.

SYMPTOM CAUSE SOLUTION

No sound. Volume is Increase volume.

set to minimum.

AM or FM, no sound. Power is not on.

Volume is Increase volume.

set to minimum.

AM/FM, poor sound. Station is not tuned Retune the AM or FM

properly. broadcast station.

FM: Extend AC cord.

AC cord is not

extended.

AM: Unit is not pos- Rotate unit until best

itioned correctly. reception is obtained.

iPod mode, no sound. Incorrectly connected. Check the connection.

Not in iPod mode.

Time reset to “12:00”. Batteries connected Check the batteries.

improperly, not con-

nected or dead.

Clock not set.

Alarm does not Alarm is not activated Set and activate alarm as

turn on. or set properly. described on page 16.

Clock is not set.

23

Press the STANDBY ON

button, then iPod/AUX/AM/FM

button to select AM or FM.

Press iPod/AUX/AM/FM button.

Set the clock, see page 15.

Set the clock, see page 15.

LIMITED WARRANTY (Valid in the United States)

Emerson Radio Corp. warrants manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions, for a period of ninety
(90) days from the date of original purchase in the U.S. With your dated proof of purchase,
we will provide repair service at no charge for labor and parts at an authorized Depot
Repair Facility, or replace the product in our discretion. For repair or replacement, pack
your unit in a padded box, enclose your check or money order payable to Emerson Radio
Corp. in the amount of $9.00 (not required by California residents) to cover shipping and
handling costs, and enclose a copy of your proof of purchase. Send your unit to:

This warranty does not cover damage from negligence, misuse, abuse, accident, failure to
follow operating instructions, commercial use, rental, repairs by an unauthorized facility, or
products purchased, used, serviced or damaged outside of the United States.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

The serial number of your system is located on a label on the bottom cabinet. Please take
a moment now to locate the serial number and write the number in the space provided
below. You may be asked to provide this number when calling for product service.

Model Number: BAR710
Serial Number:

EMERSON RADIO CORP.

Emerson Radio Corp.

5101 Statesman Drive

Irving, TX 75063

AU898M

__________________________________________

24

EMERSON®WARRANTY (Valid in Canada)

Consumer Electronics, Home Appliances and Home Office Products

Thank you for choosing EMERSON

®

!

SYNNEX Canada Limited gives the following express warranty to the original consumer purchaser or gift recipient for this
EMERSON product, when shipped in its original container and sold or distributed in Canada by SYNNEX Canada Limited
or by an Authorized EMERSON Dealer:

SYNNEX Canada Limited warrants that this product is free, under normal use and maintenance, from any defects in
material and workmanship. If any such defects should be found in this product within the applicable warranty period,
SYNNEX Canada Limited shall, at its option, repair or replace the product as specified herein. Replacement parts
furnished in connection with this warranty shall be warranted for a period equal to the unexpired portion of the original
equipment warranty.

This warranty shall not apply to:

a. Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper

installation or inappropriate use as outlined in the owner’s manual.

b. Any EMERSON product tampered with, modified, adjusted or repaired by any party other than SYNNEX Canada

Limited or EMERSON’s Authorized Service Centres.

c. Damage caused or repairs required as a result of the use with items not specified or approved by SYNNEX

Canada Limited, including but not limited to head cleaning tapes and chemical cleaning agents.

d. Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the

product including but not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus,
trays, filters, cables, paper, cabinet, cabinet parts, knobs, buttons, baskets, stands, shelves, cookware and

cooking utensils.
e. Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear.
f. Any damage caused by external or environmental conditions, including but not limited to transmission line/power

line voltage or liquid spillage.
g. Any product received without appropriate model, serial number and CSA /cUL /cULus /cETL /cETLus markings.
h. Any products used for rental or commercial purposes.
i. Any installation, setup and/or programming charges.

Should this EMERSON product fail to operate during the warranty period, warranty service may be obtained upon delivery
of the EMERSON product together with proof of purchase and a copy of this LIMITED WARRANTY statement to an
Authorized EMERSON Service Centre. This warranty constitutes the entire express warranty granted by SYNNEX
Canada Limited and no other dealer, service centre or their agent or employee is authorized to extend, enlarge or transfer
this warranty on behalf of SYNNEX Canada Limited. To the extent the law permits, SYNNEX Canada Limited disclaims
any and all liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss
of profits resulting from a defect in material or workmanship relating to the product, including damages for the loss of time
or use of this EMERSON product or the loss of information. The purchaser will be responsible for any removal,
reinstallation, transportation and insurance costs incurred. Correction of defects, in the manner and period of time
described herein, constitute complete fulfillment of all obligations and responsibilities of SYNNEX Canada Limited to the
purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on contract,
negligence, strict liability or otherwise.

CARRY-IN PARTS & LABOUR WARRANTY PERIODS:

• Audio Products: 1 Year (Remote Control, if applicable – 90 Days)

• Home Appliances: 1 Year

o Microwave Magnetron parts only additional 3 Years
o Refrigerator / Freezer Compressor parts only, additional 4 years

• Home Office Products: 1 Year

To obtain the name and address of the nearest Authorized EMERSON Service Centre or for more information on this warranty

- visit www.emersonelectronics.ca

- mail your inquiry to: SYNNEX Canada Limited, EMERSON Customer Service
200 Ronson Drive, Toronto, ON M9W 5Z9; or

- call toll free 1-800-663-5954, Monday to Friday 9:00am – 5:00pm Eastern Standard Time.

08.2007

25

BAR710-081207-02 Printed in China

®