Baran Advanced Technologies ASHKB Users Manual

Prox card. The unit will read the content and send it over the Data wires to the Controller. Enter PIN code. The unit will

The Keypad and the Prox reader are interlocked so that when one is functioning the other is

5 cm distance maximum. The unit will activate the Buzzer once and the illuminated LED will blink.

NOTE: Thi

installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur

a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

i

CLASS™

EVERSWITCH

Model: ASHKB
Output formats- iCLASS Card - Wiegand 26

- Keypad: - 8 Bit
Power Supply : 10 - 16 VDC reverse voltage
protected

Power Consumption: Ave. 70mA Peak 250 mA
Transmitter/Receiver frequency: 13.56 Mhz
Mounting: Universal USA and EUROPE
Environment: IP68 ; 100% relative humidity
Operating Temperature: - 20 to + 70ºC
Dimensions: 120 x 90 x 25 ( 4,72 / 3.54 /1.00 )
Antitamper Optical protection

Certifications:

Operation Modes:

The iCLASS reader is equipped with 2 electronically interlocked devices. The iCLASS Proximity Reader and the Piezoelectric Keypad.
The iCLASS reader supports the following operation modes:

1. Prox – Pin. Present iCLASS
send the PIN code over the same Data wires to the host.
inhibited until the data is transmitted.

2. Prox Only. The prox electronics is independently communicating via Data wires.

3. Keypad only. The keypad electronics is independently communicating via Data wires.
Verification

Power up the unit. The buzzer will beep once . In the same time the RED or the Green LED will come ON depending on the Central Controller setup.
Present a valid HID encrypted iCLASS card at 2.
Enter a key . The unit will activate the Buzzer once.

PROXIMTY READ PLUS KEYPAD

Wiring Recommended cable is ALPHA 1295 ( 22AWG) 5-conductor stranded with overall shield or equivalent.

COLOR FUNCTION ELECTRICAL FUNCTION

RED Input Voltage 10 VDC - 16 VDC
BLACK Ground
GREEN Data 0 Open collector 1Kohm pull-up to internal +5V
WHITE Data 1 Open collector 1Kohm pull-up to internal +5V
BROWN LED Input
BLUE CCTV output Open collector 0,150 mA activated with each key for 30 sec
VIOLET Housing Ground
ORANGE Buffered Input

GREY Tamper Output Open collector 0,100 A “Low” when light sensed

1. Blue Wire - PRESSING any key on the keypad will generate a 30 seconds 0.25 amp permanent duty grounding output.

2. Orange Wire - When the Hold Line, Orange wire, is pulled “low”, the iClass data communication is inhibited.

3. Grey Wire - When the photodiode senses ambient light the wire is pulled “LOW”

provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

s equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

in
user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this equipment not expressly approved by the party responsible for compliance Baran Advanced Technologies (86) Ltd. could void the user’s
authority to operate the equipment.

ct satisfies the requirements of :