IWR-220XR
Operation Manual
Cautions:
Functions of Receiver IWR-220XR
l
l
l
l
l
l
Do not cover the infrared emitter area of the wireless microphone or the
surface of the infrared sensor, which may disturb the unit and cause
abnormal operation.
Since the unit uses infrared reflectance. Do not expose receive to the black
ceiling or wall which may cause abnormal operation.
Do not near the speaker which may cause howling.
Do not drop and wet microphone.
Do not replace the battery when power is on.
Do not install the unit a location near heat source or in a place subject to
direct sunlight, excessive dust, mechanical vibration or shock.
Front Panel Rear Panel
1.
2.
Green LED will light up accordingly when receives the infrared signal
from microphone.
3.
Microphone output jacks that connect the mixed microphone output with
cable provided to the amplifier.
4.
It changes the output level of the microphone. Set it to LINE when
connecting the output jack to the AUX input of the amplifier or set it to MIC
when connecting the MIC jack of the amplifier.
5.
Connect to infrared external sensor.
6.
Press it down to turn on the receiver, the power indicator will light up.
Press it again to turn off, the power indicator will go off accordingly.
7.
Supplies power to the unit.
Power indicator
Channel indicator
Mic outputs (A+B Mix)
Mic/Line output level switch
Infrared sensor inputs
Power switch
AC cord
l
l
l
l
l
l
Flat 04,2/F., Yuen Fat Industrial Building,
25 Wang Chiu Road, Kowloon Bay,
Kowloon, HongKong
Tel:(852)2571 8289 Fax: (852)2571 0289
Web site: www.bap.com.hk
Email: info@bap.com.hk
Battery Charger (HC-10)
OPERATION:
1. Connect the DC plug of the adapter to the DC
socket of the charger.
2. The indication lamp is red when charging.
3. Press charge/discharge button once for
discharge (yellow) and press one more time
that will be back to charging status (red).
4. When full charge, (green) and sounded.
5. When connect the charging plug to the ring
output socket of the charger, the right
charger's trough could be an external charge.
6. The full charge capacity is 700mAH.
OPERATION:
1. Connect the Adaptor to wall outlet.
2. Insert the infrared wireless mic to the
charger.
3. The red LED of charger will light up
during charging. Charging time will be
approx. 3.5 hours.
4. When charging is completed, the
green LED indicator will turn on and
red LED turn off.
Note: Be sure to use specified battery
only. You can not charge other
type of battery. Do not use any
battery and battery charger other
than specified.
Handheld Mic Charger Holder (HC-20)
Connection Diagram
u
v
w
x
u
v
w
x
y
u
vw
y
x
Functions of Handheld Microphone
IWH-201XP
1.
2.
Two-color power ON/Low battery LED changes color to indicate low
batteries.
3.
Slide to turn microphone on.
4.
Transmitting the infrared ray which carrying voice.
5.
This switch changes transmitting power of infrared ray.
If transmission system may pick up some noise at Lo position. It means
the transmitting distance may be insufficient. Set the switch to Hi
position.
Factory setting is Hi position.
Grille cover
Low battery indicator
Power switch
Infrared emission source
Power selector switch (Lo/Hi)
l
l
l
l
l
l
u
Functions of Tie-Clip Microphone
IWM-202XP
1.
2.
Two-color power ON/Low battery LED
changes color to indicate low batteries.
3.
Slide to turn microphone on.
4.
Transmitting the infrared ray which carrying
voice.
5.
Input audio level control serves as remote
volume control.
Lavalier or Headworn Microphone
Low battery indicator
Power switch
Infrared emission source
Volume Control
l
l
l
l
1.
Microphone with infrared emission source
that transmits infrared ray which carrying
voice.
2.
Two-color power ON/Low battery LED
changes color to indicate low batteries.
3.
Slide to turn microphone on.
4.
Input audio level control serves as remote
volume control.
Microphone with built-in infrared emission
Low battery indicator
Power switch
Volume Control
l
l
l
l
Mounting the Infrared External Sensor
IR-20X
Functions of Neckworn Microphone
IWM-303
Example of ideal position for sensor
Covering range of infrared rays.
1. Mount the FIXING HOLDER (wall or ceiling) by using a screw or two pieces
of double coated tape.
2. Find the best position with wide view of the room. Mount the sensor along
with the FIXING HOLDER on the wall or ceiling.
Note: When power up, the LED of infrared sensor will light up to red if not
please consult with your nearest dealer.
Loading...